1. Distillation of sample mixture of pentane and hexane. Determine which organic compound will distil out first? 2. A student carried out a simple distillation on a compound known to boil at 124°C and reported an observed boiling point of 116-117°C. Gas chromatographic analysis of the product showed that the compound was pure, and a calibration 1 of the thermometer indicated that it was accurate. What procedural error might the student have made in setting up the distillation apparatus? 3. The directions in an experiment specify that the solvent, diethyl ether, be removed from the product by using a simple distillation. Why should the heat source for this distillation be a steam bath, not an electrical heating mantie?

Answers

Answer 1

In the distillation of a pentane and hexane mixture, pentane will distill out first due to its lower boiling point.

Pentane (C5H12) will distill out first in the distillation of a mixture of pentane and hexane. This is because pentane has a lower boiling point (36.1°C) compared to hexane (69°C). During distillation, as the temperature increases, the component with the lower boiling point vaporizes first and is collected as the distillate.

The procedural error that the student might have made in setting up the distillation apparatus is improper temperature measurement. The student's observed boiling point of 116-117°C is lower than the expected boiling point of 124°C. This discrepancy suggests that the temperature measurement during the distillation was inaccurate. The student may have placed the thermometer too high above the boiling flask or failed to properly immerse it in the vapor phase, leading to a lower temperature reading.

The heat source for the distillation of diethyl ether should be a steam bath rather than an electrical heating mantel. Diethyl ether is a highly volatile and flammable solvent with a low boiling point (34.6°C). Using an electrical heating mantel, which directly applies heat to the flask, can create a potential fire hazard due to the flammability of diethyl ether. A steam bath, on the other hand, indirectly heats the distillation flask using hot steam, reducing the risk of ignition and providing better control over the heating process.

In the distillation of a pentane and hexane mixture, pentane will distill out first due to its lower boiling point. The student's error in setting up the distillation apparatus might be inaccurate temperature measurement. When removing diethyl ether by distillation, a steam bath should be used as the heat source to minimize the risk of fire associated with the highly flammable nature of diethyl ether.

To know more about pentane , visit :

https://brainly.com/question/32575022

#SPJ11


Related Questions

The sample has a median grain size of 0.037 cm, and a porosity of 0.30.The test is conducted using pure water at 20°C. Determine the Darcy velocity, average interstitial velocity, and also assess the validity of the Darcy's Law.

Answers

The Darcy velocity of the soil sample is 3.83 * 10^-5 m/s and the average interstitial velocity is 1.28 * 10^-4 m/s. As the calculated value of Darcy velocity is much less than the average interstitial velocity, Darcy's law is not valid.

Darcy’s Law expresses that the velocity of flow of water through a porous medium is proportional to the hydraulic gradient applied. When the fluid's viscosity is constant and inertial forces are negligible, Darcy’s Law may be applied.

Mathematically, the law is represented by the following expression : Q = KAI/L

where,Q = flow of water (m3/s) ; K = hydraulic conductivity (m/s) ; A = cross-sectional area of the soil sample (m2) ;

I = hydraulic gradient (head loss/unit distance) ; L = length of the soil sample (m)

Firstly, let us calculate the hydraulic conductivity of the soil sample using the Hazen’s formula.

Hazen’s formula states that hydraulic conductivity can be calculated using the following formula : K = c * d2

where, K = hydraulic conductivity (m/s) ; c = a constant and d = the median grain size in millimetres

We know, c = 2.86 for pure water at 20°C.d = 0.037 cm = 0.37 mm

Therefore, K = 2.86 * 0.372 = 0.383 * 10^-4 m/s

Calculating Darcy velocity, Vd, we get Vd = (Q * μ) / (A * H)

where, Vd = Darcy velocity (m/s) ; Q = Flow of water (m3/s) ; μ = Viscosity of pure water (m2/s) ; A = Cross-sectional area of the sample (m2) ; H = Hydraulic head (m)

We know, A = 0.01 * 0.01 m2 = 10^-4 m2 ; μ = 0.001 Pa.s = 10^-3 N.s/m2 ;

Q = KA * I/L = 0.383 * 10^-4 * 10^-4 * 10/(100 * 10^-2) = 3.83 * 10^-8 m3/sI = H/L = 0.1/0.1 = 1m/m

Hence, Q = 3.83 * 10^-8 m3/s ; μ = 10^-3 N.s/m2 ; A = 10^-4 m2, H = 0.1 m ; L = 0.1 m.

So, Vd = (3.83 * 10^-8 * 10^-3) / (10^-4 * 0.1) = 3.83 * 10^-5 m/s

Therefore, the Darcy velocity of the soil sample is 3.83 * 10^-5 m/s.

We can calculate the average interstitial velocity using the formula, Vi = Q/φA,

where φ = Porosity = 0.30 ; Q = 3.83 * 10^-8 m3/s ; A = 10^-4 m2

Therefore, Vi = (3.83 * 10^-8) / (0.30 * 10^-4) = 1.28 * 10^-4 m/s.

Thus, the Darcy velocity of the soil sample is 3.83 * 10^-5 m/s and the average interstitial velocity is 1.28 * 10^-4 m/s. As the calculated value of Darcy velocity is much less than the average interstitial velocity, Darcy's law is not valid.

To learn more about Darcy's law :

https://brainly.com/question/27005987

#SPJ11

Using specific heat capacity, calculate the enthalpy (H) if the water at 50 and 150 degrees Celsius.

Answers

The change in enthalpy (H) for 1 gram of water heated from 50°C to 150°C is 418 J.

To calculate the enthalpy (H) of water at two different temperatures, we need to consider the heat transfer and the specific heat capacity of water. The equation to calculate the change in enthalpy (ΔH) is given by: ΔH = m * c * ΔT. Where: ΔH is the change in enthalpy, m is the mass of the substance, c is the specific heat capacity of the substance, and ΔT is the change in temperature.

For water, the specific heat capacity (c) is approximately 4.18 J/g°C. Let's assume we have 1 gram of water. For the temperature change from 50°C to 150°C: ΔT = 150°C - 50°C = 100°C. Substituting the values into the equation: ΔH = 1 g * 4.18 J/g°C * 100°C = 418 J. Therefore, the change in enthalpy (H) for 1 gram of water heated from 50°C to 150°C is 418 J.

To learn more about enthalpy click here: brainly.com/question/29145818

#SPJ11

Benzene is pumped through the system at the rate of 0.434 m³/min. The density of benzene is 865 kg/m³. Calculate the power of the pump if the pump work is 1409.2 J/kg. Your answer must be in (W)

Answers

The power of the pump is calculated to be approximately X watts.,The power of the pump is approximately 8942 watts.

To calculate the power of the pump, we need to multiply the flow rate of benzene by the pump work. The flow rate is given as 0.434 m³/min, and the density of benzene is given as 865 kg/m³.

First, we need to convert the flow rate from minutes to seconds. There are 60 seconds in a minute, so the flow rate becomes 0.434 m³/60 s.

Next, we can calculate the mass flow rate by multiplying the flow rate by the density of benzene. The mass flow rate is given by (0.434 m³/60 s) * (865 kg/m³) = 6.354 kg/s.

Finally, we can calculate the power of the pump by multiplying the mass flow rate by the pump work. The power is given by (6.354 kg/s) * (1409.2 J/kg) = 8941.7968 W, which can be rounded to approximately 8942 W.

Therefore, the power of the pump is approximately 8942 watts.

Learn more about density : brainly.com/question/29775886

#SPJ11

How many liters of a 0. 325 M K2CrO4 stock solution are needed to prepare 4. 00 L of 0. 212 M K2CrO4?

Answers

Therefore, approximately 2.61 liters of the 0.325 M K2CrO4 stock solution are needed to prepare 4.00 L of the 0.212 M K2CrO4 solution.

To determine the volume of the stock solution needed to prepare the desired concentration, we can use the equation:

C1V1 = C2V2

Where:

C1 = concentration of the stock solution

V1 = volume of the stock solution

C2 = desired concentration

V2 = desired volume

Plugging in the given values:

C1 = 0.325 M

V1 = ?

C2 = 0.212 M

V2 = 4.00 L

Solving for V1:

C1V1 = C2V2

0.325 V1 = 0.212 * 4.00

0.325 V1 = 0.848

V1 = 0.848 / 0.325

V1 ≈ 2.61 L

Therefore, approximately 2.61 liters of the 0.325 M K2CrO4 stock solution are needed to prepare 4.00 L of the 0.212 M K2CrO4 solution.

Learn more about solution here

https://brainly.com/question/1616939

#SPJ11

The liquid-level process shown below is operating at a steady state when the following disturbance occurs: At time t = 0, 1 ft3 water is added suddenly (unit impulse) to the tank; at t = 1 min, 2 ft3

Answers

Answer : The level in the tank drops by 1/2 ft at t = 1 min after the addition of 2 ft3 of water.

The given liquid level process is operating at a steady state until a disturbance is introduced. Here, we can calculate the level response to the sudden impulse and then to the addition of 2 ft3 of water at t = 1 min.

The given data can be summarized as follows:

At t = 0, the unit impulse is introduced.

At t = 1 min, 2 ft3 water is added.

Solution: To calculate the level response to the unit impulse, we first need to calculate the transfer function of the given process.

Let H(s) be the transfer function of the process, and L(s) and F(s) be the Laplace transforms of the level in the tank and the flow of the water into the tank, respectively.

From the given process, we have ,F(s) = 1/s (for the unit impulse) and F(s) = 2/s (for the addition of 2 ft3 of water at t = 1 min).

Also, L(s)/F(s) = H(s)

Let's derive H(s) by considering the following relation for the given process.

dL/dt = 1/3 (F - 2L)

Taking Laplace transform of both sides, we get,s

L(s) = 1/3 (F(s) - 2L(s))

On substituting F(s) = 1/s (for the unit impulse),

we have, sL(s) = 1/3 (1/s - 2L(s))

On solving for L(s), we get,L(s) = 1/2s - 3s/2

Now, we can use this expression of L(s) to calculate the level response to the unit impulse.

Let l(t) be the level response to the unit impulse, then, l(t) = L⁻¹ (1/s) = 1/2 - 3t/2

The level response to the addition of 2 ft3 of water at t = 1 min is given by: L(1) = 1/2 - 3(1)/2 = -1/2 ft

Know more about level here:

https://brainly.com/question/24245030

#SPJ11

The concentration of ibuprofen
in the urine of a patient with impaired kidney function is
1.65 mg/mL, and the patient's rate of urine formation is 3.1
mL/min. The patient's plasma concentration of ibu

Answers

The patient's plasma concentration of ibuprofen can be calculated using the given concentration of ibuprofen in urine (1.65 mg/mL) and the rate of urine formation (3.1 mL/min).

To determine the patient's plasma concentration of ibuprofen, we can use the principle of mass balance. The rate of urine formation multiplied by the concentration of ibuprofen in urine represents the total amount of ibuprofen excreted per minute. This is equal to the rate of elimination of ibuprofen from the plasma.

Let's denote the plasma concentration of ibuprofen as Cp (in mg/mL).Rate of elimination = Rate of urine formation * Concentration of ibuprofen in urine.Rate of elimination = 3.1 mL/min * 1.65 mg/mLNow, the rate of elimination is also equal to the rate of clearance of ibuprofen from the plasma, which is given by:

Rate of clearance = Cp * urine flow rate.Rate of clearance = Cp * 3.1 mL/min.Since the rate of elimination and the rate of clearance are equal, we can equate the two equations:.Cp * 3.1 mL/min = 3.1 mL/min * 1.65 mg/mL.Cp = 1.65 mg/mL

The patient's plasma concentration of ibuprofen is 1.65 mg/mL. This calculation is based on the given concentration of ibuprofen in urine (1.65 mg/mL) and the rate of urine formation (3.1 mL/min). It's important to note that this calculation assumes a steady-state condition and does not account for factors such as absorption, distribution, metabolism, or elimination of ibuprofen. For accurate and comprehensive assessment of drug concentration in plasma, medical professionals should consider additional factors and conduct appropriate laboratory tests or analysis.

To know more about plasma visit:

https://brainly.com/question/31510915

#SPJ11

Type of plant/animal cell: Diagram: Where is this cell found? It's found in How is this cell specialised? It has which makes it good for

Answers

The type of cell depicted in the diagram is a plant cell.

Plant cells are the basic structural and functional units of plants. They have several unique features that distinguish them from animal cells. The diagram of the plant cell typically shows various organelles and structures, including the cell wall, cell membrane, nucleus, cytoplasm, mitochondria, chloroplasts, endoplasmic reticulum, Golgi apparatus, and vacuoles.

Plant cells are found in the tissues of plants, which include leaves, stems, roots, flowers, and fruits. They are the building blocks of plant structures and are responsible for various functions, such as photosynthesis, nutrient storage, and support.

This particular plant cell may be specialized for a specific function depending on its location within the plant. For example, plant cells in the leaf tissue may be specialized for photosynthesis, while those in the root tissue may be specialized for nutrient absorption and storage. The specific specialization of the cell would depend on the organelles and structures present in the diagram.

The depicted cell is a plant cell, which is found in various tissues of plants. Its specialization and function would depend on its location within the plant and the specific organelles and structures present. Plant cells are adapted for various functions, including photosynthesis, nutrient storage, and structural support, among others.

To know more about cell , visit

https://brainly.com/question/26122239

#SPJ11

The iodate ion has a number of insoluble 4 compounds. The Ksp for AglO3 is 3.0 x 10- and the Ksp for La(10₂), is 7.5 x 10-¹² a What is the solubility of AglO, in a 0.105 M solution of NalO₂? What is the solubility of La(10), in a 0.105 M b solution of NalO₂? Which compound is more soluble?

Answers

The solubility of La(IO3)3 in a 0.105 M solution of NaIO2 is 3.1 x 10-6 M. AgIO3 has a higher solubility than La(IO3)3 in a 0.105 M solution of NaIO2.

a) The solubility of AgIO3 in a 0.105 M solution of NaIO2 is calculated by using the reaction:

AgIO3(s) ↔ Ag+ (aq) + IO3– (aq)

Let x be the solubility of AgIO3.x2 / (0.105 + x) = 3.0 x 10-8x

= 1.15 x 10-4

The solubility of AgIO3 in a 0.105 M solution of NaIO2 is 1.15 x 10-4 M.

b) The solubility of La(IO3)3 in a 0.105 M solution of NaIO2 is calculated by using the reaction:

La(IO3)3(s) ↔ La3+ (aq) + 3 IO3– (aq)

Let x be the solubility of La(IO3)3.x4 / (0.105 + 4x)3

= 7.5 x 10-13x

= 3.1 x 10-6

The solubility of La(IO3)3 in a 0.105 M solution of NaIO2 is 3.1 x 10-6 M.  

AgIO3 has a higher solubility than La(IO3)3 in a 0.105 M solution of NaIO2.

Solubility is a measure of how much solute can be dissolved in a solvent at a given temperature and pressure.

The iodate ion has several insoluble compounds. Solubility product constant (Ksp) is a term used to define the solubility of a compound in a particular solvent.

It's the product of the ion concentrations of a solid that is in a state of equilibrium with its ions in a solution.

Ksp for AglO3 is 3.0 x 10-8 and the Ksp for La(IO3)3 is 7.5 x 10-13. In a 0.105 M solution of NaIO2, the solubility of AgIO3 and La(IO3)3 are calculated.

AgIO3(s) ↔ Ag+ (aq) + IO3– (aq)

Let x be the solubility of

AgIO3. x2 / (0.105 + x) = 3.0 x 10-8 x

= 1.15 x 10-4M.

The solubility of AgIO3 in a 0.105 M solution of NaIO2 is 1.15 x 10-4 M. La(IO3)3(s) ↔ La3+ (aq) + 3 IO3– (aq)

Let x be the solubility of La(IO3)3. x4 / (0.105 + 4x)3 = 7.5 x 10-13 x

= 3.1 x 10-6 M.

To know more about compounds visit:

https://brainly.com/question/14117795

#SPJ11

1. In this experiment you are attempting to determine the amount of barium in an unknown sample by precipitating all of the barium as its sulfate salt. Would this method work if you were attempting to determine the amount of sodium in an unknown sample? Why or why not? 2. If you skip the 30 min drying step before weighing the crucible, paper, and BaSO 4

will your calculated value for % Barium in sample be too high or too low? 3. The percent by mass of barium calculated should be less than 100%. What accounts for the remaining mass percent of your original sample?

Answers

The method of precipitating barium as its sulfate salt would not work if you were attempting to determine the amount of sodium in an unknown sample.

This is because the principle behind this method relies on the selective precipitation of barium sulfate, which has a very low solubility product constant (Ksp). When a soluble sulfate salt (such as sodium sulfate) is added to a solution containing barium ions, it forms an insoluble precipitate of barium sulfate. However, sodium ions do not form an insoluble precipitate with sulfate ions. Therefore, adding a soluble sulfate salt would not result in the precipitation of sodium as a sulfate salt, making it impossible to determine the amount of sodium using this method.

If the drying step before weighing the crucible, paper, and BaSO4 is skipped, the calculated value for the percent of barium in the sample would be too high. This is because the drying step is essential to remove any residual water or moisture from the sample, including water molecules that might have adsorbed onto the precipitate. Skipping the drying step would result in an artificially higher mass of the precipitate, leading to an overestimation of the percent of barium in the sample.

The remaining mass percent of the original sample, after determining the percent of barium, would be accounted for by other components present in the sample. In most cases, samples are not pure substances but rather mixtures of different compounds or elements. The original sample may contain other elements or compounds that were not targeted or analyzed in the specific procedure used to determine the barium content. These additional components contribute to the total mass of the sample, and their percentage would be calculated separately if desired. For example, if the original sample contained sodium along with barium, the percent of sodium could be determined using a different method suitable for sodium analysis. The sum of the percent of barium and percent of other components should then account for the total mass percent of the original sample.

Learn more about barium sulfate at: brainly.com/question/2782682

#SPJ11

help me answer this.

Answers

a. Balancing the redox reaction in both acidic and basic mediums:

Fe²+ + [tex]MnO_4[/tex]- --> Fe³+ + Mn²+.

b. Balancing the redox reaction in both acidic and basic mediums:

Cu + [tex]NO_3[/tex]- --> Cu+2 +[tex]N_2O_4.[/tex]

a. Fe²+ + [tex]MnO_4[/tex]- --> Fe³+ + Mn²+

Balanced equation in acidic medium:

Fe²+ + [tex]MnO_4[/tex]- --> Fe³+ + Mn²+

To balance the equation, we can follow these steps:

1)Assign oxidation numbers to each element:

Fe²+ (Fe has a +2 oxidation state)

[tex]MnO_4[/tex]- (Mn has a +7 oxidation state)

2)Identify the element being reduced and the element being oxidized:

Fe²+ is being oxidized (from +2 to +3)

[tex]MnO_4[/tex]- is being reduced (from +7 to +2)

3)Balance the atoms and charges for each half-reaction:

Oxidation half-reaction: Fe²+ --> Fe³+ (requires one Fe²+ and one electron)

Reduction half-reaction:[tex]MnO_4[/tex]- --> Mn²+ (requires five electrons and eight H+ ions to balance charges)

4)Balance the number of electrons in both half-reactions:

Multiply the oxidation half-reaction by 5 and the reduction half-reaction by 1 to equalize the number of electrons in both half-reactions.

The balanced equation in acidic medium is:

5Fe²+ + [tex]MnO_4[/tex]- + 8H+ --> 5Fe³+ + Mn²+ + 4H2O

Balanced equation in basic medium:

To balance the equation in a basic medium, we need to add OH- ions to both sides to neutralize the H+ ions.

The balanced equation in basic medium is:

5Fe²+ + [tex]MnO_4[/tex]- + 8OH- --> 5Fe³+ + Mn²+ + 4[tex]H_2O[/tex]

Overall charge balancing:

In both acidic and basic media, the overall charges are balanced, with an equal number of positive and negative charges on both sides of the equations.

b. Cu + [tex]NO_3[/tex]- --> Cu+2 + N₂O4

Balanced equation in acidic medium:

Cu + [tex]NO_3[/tex]- --> Cu+2 + N₂O4

To balance the equation, we can follow these steps:

1)Assign oxidation numbers to each element:

Cu (Cu has a 0 oxidation state)

[tex]NO_3[/tex]- (N has a +5 oxidation state)

2)Identify the element being reduced and the element being oxidized:

Cu is being oxidized (from 0 to +2)

[tex]NO_3[/tex]- is being reduced (from +5 to +4)

3)Balance the atoms and charges for each half-reaction:

Oxidation half-reaction: Cu --> Cu+2 (requires two electrons)

Reduction half-reaction: [tex]NO_3[/tex]- --> N₂O4 (requires three electrons)

4)Balance the number of electrons in both half-reactions:

Multiply the oxidation half-reaction by 3 and the reduction half-reaction by 2 to equalize the number of electrons in both half-reactions.

The balanced equation in acidic medium is:

3Cu + 2[tex]NO_3[/tex]- --> 3Cu+2 + N₂O4

Balanced equation in basic medium:

To balance the equation in a basic medium, we need to add OH- ions to both sides to neutralize the H+ ions.

The balanced equation in basic medium is:

3Cu + 2[tex]NO_3[/tex]- + 6OH- --> 3Cu+2 + N₂O4+ 3[tex]H_2O[/tex]

Overall charge balancing:

In both acidic and basic media, the overall charges are balanced, with an equal number of positive and negative charges on both sides of the equations

The complete question is :

Balance the following redox reactions in both acidic and basic medium using the ion-electron method.

Rubrics:

1pt balanced equation acidic medium.

1pt balanced equation basic medium.

1pt balance overall charges of acid and basic medium.

a. Fe²+ + [tex]MnO_4[/tex]-  --> Fe³+ + Mn²+

b. Cu + [tex]NO_3[/tex] --> Cu +2 + N₂O4

Know more about  acidic medium   here:

https://brainly.com/question/24255408

#SPJ8

Ethanol-Water Separations. We wish to separate ethanol from water in a sieve-plate distillation column with a total condenser and a partial reboiler. There are two feed streams:
Feed
Flowrate (mol/hr)
ZF Thermal State
1
200
0.4 subcooled liquid
2
300
0.3 saturated vapor
"Feed 2 condenses 0.25 moles of vapor for every mole of feed.
The bottoms product should be 2% (mol) ethanol and the distillate should be 72% (mol) ethanol.
Notes:
The reflux ratio is equal to (1.0) and the feeds are to be input at their optimum location(s).
Both feeds are being input into the column, e.g. this is not intended to be solving for two unique columns but just one that has two input feed streams.
⚫ Equilibrium data for Ethanol-Water at 1 bar is shown in the table.
You may also identify / use other experimental data (web sources, library) for this system.
a) What are the flowrates of the distillate and bottoms products?
b) What are the flowrates of liquid and vapor on stages between the two feeds points? c) Determine the number of equilibrium stages required for the separation.
How many of these stages are in the column?
d) Label the two feed stages.
Label the point that represents the liquid stream leaving the 3rd plate above the reboiler and the vapor stream passing this liquid.

Answers

Distillation column for ethanol-water separation calculates flowrates, equilibrium stages, and identifies feed stages to achieve desired compositions and optimize the process.

a) The flowrate of the distillate product can be calculated by considering the reflux ratio and the desired composition. Since the reflux ratio is 1.0 and the distillate should be 72% (mol) ethanol, the flowrate of the distillate can be determined as a fraction of the total flowrate entering the column. Similarly, the flowrate of the bottoms product, which should be 2% (mol) ethanol, can be calculated.

b) The flowrates of liquid and vapor on stages between the two feed points can be determined using material and energy balances. By considering the feed conditions, reflux ratio, and desired compositions, the flowrates of liquid and vapor on each stage can be calculated.

c) The number of equilibrium stages required for the separation depends on the desired separation efficiency. It can be determined by comparing the compositions of liquid and vapor at each stage with the equilibrium data for the ethanol-water system. The separation efficiency can be improved by increasing the number of stages in the column.

d) The feed stages can be identified as the stages where the two feed streams enter the column. The point representing the liquid stream leaving the 3rd plate above the reboiler can be labeled as the point of interest. This point represents the liquid stream that will be further processed in the reboiler and contributes to the vapor stream leaving the column.

Learn more about equilibrium  : brainly.com/question/30694482

#SPJ11

Discuss reverse osmosis water treatment process? 1.5 After discovering bird droppings/poop around campus, you decide to build a water treatment plant for the campus. You need to advice our university principal regarding the feasibility of your project, why is it important for you to build the plant, how will it help in alleviating the droppings, if the process is feasible you need to draw water treatment that you will use.

Answers

Reverse osmosis is a feasible water treatment process that can effectively alleviate the issue of bird droppings on campus.

It is important to build a water treatment plant because it will ensure the availability of clean and safe drinking water for the university community.

Reverse osmosis is a water purification process that uses a semipermeable membrane to remove contaminants from water. It works by applying pressure to the water, forcing it to pass through the membrane while leaving behind impurities.

In the case of bird droppings, reverse osmosis can effectively remove any potential contaminants present in the water. Bird droppings may contain harmful microorganisms, bacteria, and other pollutants, which can pose health risks if consumed. By implementing a reverse osmosis water treatment plant, the water can be purified, ensuring it is safe for drinking and other uses.

The feasibility of the project depends on factors such as the availability of a water source, the size of the campus, and the budget allocated for the construction and maintenance of the water treatment plant. An engineering and financial assessment should be conducted to determine the specific requirements and costs associated with the project.

Building a water treatment plant using reverse osmosis is crucial for addressing the issue of bird droppings on campus. It will provide a reliable source of clean and safe drinking water for the university community. Additionally, it will help alleviate concerns about potential health risks associated with consuming water contaminated by bird droppings. However, a thorough feasibility study should be conducted to assess the project's viability and determine the appropriate design and budget for the water treatment plant.

To know more about Osmosis, visit

brainly.com/question/14752507

#SPJ11

Which of the following are among chemicals connected with increased acute and chronic disease in humans? Select all that apply.
Question 1 options:
A) Oxygen
B) Pb (Lead)
C) Pyrethroids
D) NaCl
E) BPA
F) PCBs&PBBS
G) Dioxins
H) Organophosphate Pesticides

Answers

Chronic diseases are a leading cause of death worldwide, and exposure to certain chemicals has been linked to an increased risk of these diseases.

The following are among the chemicals associated with increased acute and chronic illness in humans:

Pyrethroids

PCBs&PBBS

Dioxins

Organophosphate Pesticides

Pyrethroids are a group of insecticides that are frequently used to control insects in domestic and industrial settings. They can cause neurotoxic effects and are connected to acute and chronic health problems in humans, including respiratory problems, skin irritation, and asthma. Long-term pyrethroid exposure has been linked to the development of Parkinson's disease.

PCBs (polychlorinated biphenyls) and PBBS (polychlorinated biphenyls) are a group of chemicals that were widely used in industrial settings before being phased out in the 1970s. They have been linked to a variety of acute and chronic health problems in humans, including skin disorders, liver disease, and cancer.

Dioxins are a group of chemicals that are formed as by-products during the incineration of waste. They can cause a wide range of acute and chronic health problems in humans, including immune system disorders, cancer, and reproductive problems.

Organophosphate pesticides are a type of insecticide that is commonly used in agriculture. They can cause acute and chronic health problems in humans, including headaches, dizziness, and respiratory problems. Long-term exposure to organophosphate pesticides has been linked to the development of Parkinson's disease.

To know more about chronic disease visit:

https://brainly.com/question/30368140

#SPJ11

Evaporation exercise – Double effect
20,000 kg/h of an aqueous solution of NaOH at 5% by weight is to be
concentrated in a
double effect of direct currents up to 40% by weight. Saturated
steam at 3.

Answers

To concentrate 20,000 kg/h of an aqueous solution of NaOH from 5% to 40% by weight using a double-effect evaporation system with direct currents, saturated steam at 3.0 bar is required.

To calculate the amount of steam required for evaporation, we need to consider the water evaporation rate and the concentration change.

Given:

Inlet solution flow rate (Qin) = 20,000 kg/h

Inlet concentration (Cin) = 5% by weight

Outlet concentration (Cout) = 40% by weight

First, calculate the water evaporation rate:

Water evaporation rate = Qin * (1 - Cout/100)

                     = 20,000 kg/h * (1 - 40/100)

                     = 20,000 kg/h * 0.6

                     = 12,000 kg/h

Next, determine the steam required for evaporation:

Steam required = Water evaporation rate / Steam quality

              = 12,000 kg/h / Steam quality

The steam quality depends on the operating pressure of the evaporation system. Since saturated steam at 3.0 bar is mentioned, the steam quality can be estimated using steam tables or steam properties charts.

To concentrate 20,000 kg/h of an aqueous solution of NaOH from 5% to 40% by weight using a double-effect evaporation system with direct currents, the exact amount of steam required depends on the steam quality at the operating pressure of 3.0 bar. Additional calculations using steam tables or steam properties charts are necessary to determine the specific steam quantity needed.

To know more about NaOH , visit

https://brainly.com/question/29636119

#SPJ11

4. A fluidized-bed, immobilized-cell bioreactor is used for the conversion of glucose to ethanol by Z.mobilis cells immobilized in K-carrageenan gel beads. The dimensions of the bed are 10cm (diameter) by 200 cm. Since the reactor is fed from the bottom of the column and because of CO₂ gas evolution, cell concentrations decrease with the height of the column. The average cell concentration at the bottom of the column is [X]. = 45g/L and the average cell concentration decreases with the column height according to the following equation: X=X, (1-0.005Z) where Z is the column height (cm). The specific rate of substrate consumption is q=2 g substrate /g cells h. The feed flow rate and glucose concentration in the feed are 5L/h and 160 g glucose/L, respectively. a) determine the substrate concentration in the effluent b) Determine the ethanol concentration in the effluent if Yp/s =0.48 g eth/g glu.

Answers

a) The substrate concentration in the effluent is not meaningful or possible under the given conditions.

b) The ethanol concentration in the effluent is 216 g/L.

a) To determine the substrate concentration in the effluent, we need to consider the substrate consumption by the cells along the column height.

Given:

Feed flow rate (Q) = 5 L/h

Glucose concentration in the feed (Cglu) = 160 g/L

Specific rate of substrate consumption (q) = 2 g substrate/g cells h

Column height (Z) = 200 cm

Initial cell concentration at the bottom of the column ([X]₀) = 45 g/L

The substrate consumption can be calculated using the specific rate of substrate consumption and the cell concentration at each height:

Substrate consumption rate (Rglu) = q * X

The substrate concentration in the effluent can be determined by subtracting the substrate consumption rate from the feed concentration:

Substrate concentration in the effluent (Cglu_effluent) = Cglu - (Rglu * Q)

Now, let's calculate the substrate concentration in the effluent:

At the bottom of the column (Z = 0 cm):

Rglu₀ = q * [X]₀ = 2 g substrate/g cells h * 45 g/L = 90 g substrate/L h

Cglu_effluent = Cglu - (Rglu₀ * Q)

              = 160 g/L - (90 g substrate/L h * 5 L/h)

              = 160 g/L - 450 g substrate/L

              = -290 g substrate/L

Since the calculated value is negative, it suggests that the substrate concentration in the effluent is not meaningful or possible under the given conditions.

b) To determine the ethanol concentration in the effluent, we need to use the yield coefficient (Yp/s).

Given:

Yield coefficient (Yp/s) = 0.48 g eth/g glu

Ethanol production rate (Reth) = Yp/s * Rglu

The ethanol concentration in the effluent can be calculated as:

Ethanol concentration in the effluent (Ceth_effluent) = Reth * Q

Let's calculate the ethanol concentration in the effluent:

Reth = Yp/s * Rglu₀ = 0.48 g eth/g glu * 90 g substrate/L h = 43.2 g eth/L h

Ceth_effluent = Reth * Q = 43.2 g eth/L h * 5 L/h = 216 g eth/L

Therefore, the ethanol concentration in the effluent is 216 g/L.

Read more on  consumption rate here: https://brainly.com/question/29588843

#SPJ11

8. (30 points) Find the fugacity (kPa) of compressed water at 25 °C and 1 bar. For H₂O: Te = 647 K, P = 22.12 MPa, w = 0.344

Answers

The fugacity of compressed water at 25 °C and 1 bar is approximately 97.58 kPa.

To find the fugacity of compressed water at 25 °C and 1 bar using the Peng-Robinson equation of state.

Given:

Te = 647 K (critical temperature of water)

P = 1 bar (pressure)

w = 0.344 (acentric factor)

We need to calculate the Peng-Robinson parameters A and B:

A = 0.45724 × (R × Te)² / Pc

B = 0.07780 × (R × Te) / Pc

Where:

R = 8.314 J/(mol·K) (gas constant)

Pc = 22.12 MPa = 22120 kPa (critical pressure of water)

Substituting the values:

A = 0.45724 × (8.314 × 647)² / 22120 ≈ 0.1251 kPa·m³/mol²

B = 0.07780 × (8.314 × 647) / 22120 ≈ 0.02366 m³/mol

Now, we can solve the Peng-Robinson equation of state to find the compressibility factor Z. This equation is a cubic equation and requires an iterative method such as the Newton-Raphson method to solve it. However, since we know that the system is pure water at low pressure, we can approximate Z as 1.

Using the approximation Z ≈ 1, the fugacity coefficient (φ) is given by:

ln(φ) = Z - 1 - ln(Z - B) - A/(2√2B) * ln[(Z + (1 + √2)B)/(Z + (1 - √2)B)]

Substituting Z = 1:

ln(φ) = 1 - 1 - ln(1 - 0.02366) - 0.1251 / (2√2 * 0.02366) × ln[(1 + (1 + √2) * 0.02366)/(1 + (1 - √2) × 0.02366)]

Simplifying the equation:

ln(φ) = - ln(0.97634) - 0.1251 / (2√2 × 0.02366) × ln[(1 + 1.4142 × 0.02366)/(1 - 1.4142 × 0.02366)]

ln(φ) = -0.02437

Taking the exponential of both sides to find φ:

φ ≈ e^(-0.02437) ≈ 0.9758

The fugacity (f) can be calculated by multiplying the fugacity coefficient (φ) with the pressure (P):

f = φ × P ≈ 0.9758 × 1 bar ≈ 0.9758 bar ≈ 97.58 kPa

Therefore, the fugacity of compressed water at 25 °C and 1 bar is approximately 97.58 kPa.

Read more on compressibility factor here: https://brainly.com/question/17463662

#SPJ11

cance do not calculate
QUESTION 2 [15 MARKS] Water in the bottom of a narrow metal tube is held at constant temperature of 233 K. The total pressure of air (Assumed dry) I 1.21325*105 Pa and the temperature is 233 K. Water

Answers

The pressure of water vapor in the narrow metal tube is 1.21325 * 10^5 Pa at a temperature of 233 K.

To determine the pressure of water vapor in the narrow metal tube, we can use the concept of vapor pressure. Vapor pressure is the pressure exerted by a vapor in equilibrium with its liquid or solid phase at a specific temperature.

In this case, the water in the bottom of the narrow metal tube is at a constant temperature of 233 K. At this temperature, we can refer to a vapor pressure table or use the Antoine equation to find the vapor pressure of water.

Using the Antoine equation for water vapor pressure, which is given by:

log(P) = A - (B / (T + C))

where P is the vapor pressure in Pascal (Pa), T is the temperature in Kelvin (K), and A, B, and C are constants specific to the substance.

For water, the Antoine constants are:

A = 8.07131

B = 1730.63

C = 233.426

Plugging in the values, we can calculate the vapor pressure of water at 233 K:

log(P) = 8.07131 - (1730.63 / (233 + 233.426))

log(P) = 8.07131 - (1730.63 / 466.426)

log(P) = 8.07131 - 3.71259

log(P) = 4.35872

Taking the antilog (exponentiating) both sides to solve for P, we get:

P = 10^(4.35872)

P ≈ 2.405 * 10^4 Pa

Therefore, the vapor pressure of water at a temperature of 233 K is approximately 2.405 * 10^4 Pa.

The pressure of water vapor in the narrow metal tube, when the water is at a constant temperature of 233 K, is approximately 2.405 * 10^4 Pa.

Water in the bottom of a narrow metal tube is held at constant temperature of 233 K. The total pressure of air (Assumed dry) I 1.21325*105 Pa and the temperature is 233 K. Water evaporates and diffuses through the air in the tube and the diffusion path z2 - Z₁ is 0.25 m long. Calculate the rate of vaporisation at steady state in kg mol/s.m². The diffusivity of the water vapor at 233 K 0.250*10-4 m²/s. Assume the system is isothermal. Where the vapor pressure of water at 330K is 5.35*10³ Pa. [15] QUESTION 2 [15 MARKS] Water in the bottom of a narrow metal tube is held at constant temperature of 233 K. The total pressure of air (Assumed dry) I 1.21325*105 Pa and the temperature is 233 K. Water evaporates and diffuses through the air in the tube and the diffusion path z2 - Z₁ is 0.25 m long. Calculate the rate of vaporisation at steady state in kg mol/s.m². The diffusivity of the water vapor at 233 K 0.250*10-4 m²/s. Assume the system is isothermal. Where the vapor pressure of water at 330K is 5.35*10³ Pa. [15]

To learn more about pressure, visit    

https://brainly.com/question/30638771

#SPJ11

QUESTION 8 The three parameters of the first order systems K, T, and to are functions of the parameters of the process

Answers

The three parameters of first-order systems of K,T,τ, namely K (gain), T (time constant), and τ (time delay), can indeed be functions of the parameters of the process. The specific values of these parameters are determined by the characteristics and dynamics of the process under consideration.

K (gain):

The gain, K, represents the amplification or attenuation of the input signal by the system. It is influenced by various process parameters, such as reaction rates, concentration gradients, flow rates, or other relevant factors. The process-specific equations or models define the relationship between these parameters and the gain of the first-order system.

T (time constant):

The time constant, T, quantifies the system's response time and indicates how quickly the system output reaches approximately 63.2% of its final value following a step change in the input. The time constant is influenced by the dynamics of the process, including reaction rates, heat transfer rates, fluid flow characteristics, and other time-dependent factors. The process-specific equations or models describe the relationship between these parameters and the time constant of the first-order system.

τ (time delay):

The time delay, τ, accounts for any delay or lag in the system's response to changes in the input. It is determined by factors such as transportation times, material residence times, communication delays, or other time-related phenomena inherent in the process. The process-specific equations or models define the relationship between these parameters and the time delay of the first-order system.

The parameters K, T, and τ of first-order systems are functions of the parameters of the process. The specific values of these parameters depend on the characteristics and dynamics of the process under consideration. By understanding the process parameters and their impact on the system's behavior, it is possible to analyze and control first-order systems effectively.

To know more about K,T,τ, visit,

https://brainly.com/question/33168680

#SPJ11

10.33 ft3/min of a liquid with density (SG=1.84) is pumped 45 feet uphill. At the inlet, the pipe inner diameter is 3 in and the liquid pressure is 18 psia. At the outlet, the pipe inner diameter is 2 in and the liquid pressure is 40 psia. The friction loss in the pipe is 11.0 ft lbf/lbm.
Determine the work required (hp) to pump the liquid.

Answers

The work required to pump the liquid is approximately 1.31 horsepower (hp).

The work required to pump the liquid, we need to consider several factors. First, we calculate the volume flow rate by converting 10.33 ft³/min to ft³/s, which is approximately 0.1722 ft³/s. Since the liquid has a specific gravity (SG) of 1.84, its density can be calculated as 1.84 times the density of water (62.4 lb/ft³), resulting in a density of approximately 114.34 lb/ft³.

Next, we calculate the head loss due to friction in the pipe. The friction loss can be calculated using the Darcy-Weisbach equation. Given the pipe length of 45 feet, the pipe diameter at the inlet of 3 inches (0.25 ft), the pipe diameter at the outlet of 2 inches (0.167 ft), and the friction loss of 11.0 ft lbf/lbm, we can determine the head loss to be approximately 3.39 ft.

Using the head loss and the density of the liquid, we calculate the total dynamic head (TDH) by adding the head loss to the elevation difference of 45 feet. The TDH is approximately 48.39 ft.

Finally, we calculate the work required to pump the liquid using the equation:

Work (hp) = (Flow rate × TDH) / (3960 × Efficiency)

Assuming an efficiency of 70%, the work required is approximately 1.31 horsepower (hp).

Learn more about density  : brainly.com/question/29775886

#SPJ11

Q1i
i) Explain the concept of inherent safety and provide two examples of process changes which demonstrate how this concept is applied.

Answers

Inherent safety is a concept that focuses on designing processes and systems to inherently minimize or eliminate hazards. Eg: process simplification and substitution of hazardous materials.

The concept of inherent safety involves making modifications to process design to eliminate or minimize hazards. One way to achieve inherent safety is through process simplification. This entails reducing the complexity of the process by eliminating unnecessary process steps, equipment, or materials that can introduce potential hazards. For example, replacing a multi-step chemical reaction with a direct synthesis method can simplify the process, reducing the number of process units and potential sources of accidents.

Another approach is the substitution of hazardous materials with less hazardous alternatives. This can involve replacing toxic or reactive substances with safer alternatives that perform the same function. For instance, replacing a corrosive chemical with a non-corrosive one or replacing a flammable solvent with a less flammable or non-flammable solvent can significantly reduce the risks associated with handling and storage.

By implementing these process changes, inherent safety seeks to eliminate or reduce the potential for accidents, fires, explosions, or releases of hazardous substances. It shifts the focus from reliance on safeguards and mitigation measures to designing processes that inherently minimize or eliminate risks, making them inherently safer and more robust.

To learn more about chemical reaction  click here, brainly.com/question/22817140

#SPJ11

A solution of a substance of unknown molecular weight is prepared by dissolving 0.2 g of the substance in 1 kg of water. This liquid solution is then placed into an apparatus with a rigid, stationary, semipermeable membrane (permeable only to water). On the other side of the membrane is pure water. At equilibrium, the pressure difference between the two compartments is equivalent to a column of 3.2 cm of water. Estimate the molecular weight of the unknown substance. The density of the solution is ~1 g/cm³ and the temperature is 300 K.

Answers

The estimated molecular weight of the unknown substance is 8001.63 g/mol.

Estimating molecular weights

To estimate the molecular weight of the unknown substance, we can use the concept of osmotic pressure.

Osmotic pressure (π) :

π = MRT

where:

π = osmotic pressureM = molarity of the solution (in mol/L)R = ideal gas constant (0.0821 L·atm/(mol·K))T = temperature in Kelvin

In this case, the osmotic pressure is equivalent to the pressure difference across the semipermeable membrane, which is 3.2 cm of water.

First, let's convert the pressure difference to atm:

1 atm = 760 mmHg = 101325 Pa

1 cm of water = 0.098 kPa

Pressure difference = 3.2 cm of water * 0.098 kPa/cm

≈ 0.3136 kPa

0.3136 kPa * (1 atm / 101.325 kPa) ≈ 0.003086 atm

Given that the density of the solution is approximately 1 g/cm³, we can assume that the solution is effectively 1 kg/L. Therefore, the molarity of the solution (M) is equal to the number of moles of the solute (unknown substance) divided by the volume of the solution (1 L):

M = (mass of substance in grams / molecular weight of substance) / (volume of solution in liters)

M = (0.2 g / molecular weight) / 1 L

M = 0.2 / molecular weight

Now we can substitute the values into the osmotic pressure equation:

0.003086 atm = (0.2 / molecular weight) * 0.0821 L·atm/(mol·K) * 300 K

0.003086 = (0.0821 * 300) / molecular weight

0.003086 * molecular weight = 0.0821 * 300

molecular weight ≈ (0.0821 * 300) / 0.003086

molecular weight ≈ 8001.63 g/mol

Therefore, the estimated molecular weight of the unknown substance is approximately 8001.63 g/mol.

More on molecular weight calculation can be found here: https://brainly.com/question/23392127

#SPJ4

3. Calculate the pH of a 0.10 M solution of the salt, NaA, the pk, for HA = 4.14

Answers

The pH of a 0.10 M solution of the salt NaA can be calculated using the pKa value of HA. If the pKa value for HA is 4.14, the pH of the solution can be determined to be less than 7, indicating an acidic solution.

The pH of the solution, we need to consider the dissociation of the salt NaA, which can be represented as Na+ + A-. The A- ion comes from the dissociation of the acid HA, where A- is the conjugate base and HA is the acid.

Since we are given the pKa value of HA as 4.14, we know that the acid is weak. A weak acid only partially dissociates in water, so we can assume that the concentration of A- in the solution is equal to the concentration of HA. Therefore, the concentration of A- is 0.10 M.

To calculate the pH, we need to determine the concentration of H+ ions. Since A- is the conjugate base of HA, it can accept H+ ions in solution. At equilibrium, the concentration of H+ ions is determined by the dissociation of water and the equilibrium constant, Kw.

As the pKa value is less than 7, indicating a weak acid, the concentration of H+ ions will be higher than the concentration of OH- ions in the solution. Therefore, the pH of the 0.10 M solution of NaA will be less than 7, indicating an acidic solution. The exact pH value can be calculated by taking the negative logarithm (base 10) of the H+ ion concentration.

Learn more about equilibrium  : brainly.com/question/30694482

#SPJ11

Tasks In your report, you must include all necessary transfer functions, plots, working out, diagrams and code for each of the tasks shown below. You should always provide evidence to support your res

Answers

The question asks for the tasks that should be included in a report and the evidence that supports the responses. Therefore, the answer should focus on listing the tasks and outlining the evidence that supports the responses. The response should include the following tasks that should be included in a report:

1. Task 1: Laplace Transforms and Transfer Functions
For this task, the report should include all the necessary transfer functions, diagrams, and code to support the working out. The evidence should include the plots showing the transfer functions and how the codes have been used to arrive at the results.

2. Task 2: Steady-State Analysis
The report should include all the necessary diagrams and code to support the working out. The evidence should include the plots showing how the codes have been used to arrive at the results.

3. Task 3: Frequency Response Analysis
For this task, the report should include all the necessary diagrams and code to support the working out. The evidence should include the plots showing how the codes have been used to arrive at the results.

4. Task 4: Time Response Analysis
For this task, the report should include all the necessary diagrams and code to support the working out. The evidence should include the plots showing how the codes have been used to arrive at the results.

In conclusion, a report should include all necessary transfer functions, plots, working out, diagrams, and code for each of the tasks as outlined above. The evidence to support the responses should include the plots showing how the codes have been used to arrive at the results.

Know more about tasks here:

https://brainly.com/question/30137065

#SPJ11

distanced travelled by the solvent front = 8cm

and

distance travelled by BLUE is 6cm

distance travelled by PINK is 5cm

distance travelled by orange is 4cm

Answers

The chromatography experiment, the solvent front traveled a distance of 8cm, while the blue, pink, and orange substances traveled distances of 6cm, 5cm, and 4cm.

In a chromatography experiment, the distance traveled by the solvent front refers to the distance the solvent traveled from the starting point on the chromatography paper. In this particular case, the solvent front traveled a distance of 8cm.

During the experiment, different components or substances were separated based on their affinity for the stationary phase and the mobile phase. The substances of interest in this scenario are represented by blue, pink, and orange.

The blue substance traveled a distance of 6cm from the starting point, indicating that it had a moderate affinity for the mobile phase. The pink substance traveled a distance of 5cm, suggesting that it had a slightly lower affinity for the mobile phase compared to the blue substance. Lastly, the orange substance traveled a distance of 4cm, indicating that it had the lowest affinity for the mobile phase among the three substances.

These distances traveled by the substances provide valuable information about their relative polarities or molecular interactions with the mobile and stationary phases. By analyzing the relative distances traveled by the substances compared to the solvent front, researchers can gain insights into the chemical properties of the separated components.

In conclusion, in this chromatography experiment, the solvent front traveled a distance of 8cm, while the blue, pink, and orange substances traveled distances of 6cm, 5cm, and 4cm, respectively, indicating their varying affinities for the mobile phase.

For more questions on molecular, click on:

https://brainly.com/question/24191825

#SPJ8

What is the vapour pressure of acetone at 58.2 deg. C? Report
your answer with units of kPa (for example: "25.2
kPa")

Answers

The vapor pressure of acetone at 58.2°C is approximately 9.48 x 10^(-71) kPa. To determine the vapor pressure of acetone at 58.2°C, we can utilize Antoine's equation.

Antoine's equation relates the temperature of a substance to its vapor pressure. The equation is typically represented as:

log(P) = A - (B / (T + C)),

For acetone, the Antoine equation constants are:

A = 14.314

B = 2756.22

C = -25.23

To convert the vapor pressure from mmHg to kPa, we'll use the conversion factor: 1 mmHg = 0.133322368 kPa.

Now, let's calculate the vapor pressure of acetone at 58.2°C.

T = 58.2°C

Substituting the values into Antoine's equation:

log(P) = 14.314 - (2756.22 / (58.2 - 25.23))

log(P) = 14.314 - (2756.22 / 32.97)

Calculating the value inside the logarithm:

log(P) = 14.314 - 83.6

log(P) = -69.286

Taking the antilogarithm:

P = 10^(-69.286)

P ≈ 7.11 x 10^(-70) mmHg

Converting from mmHg to kPa:

P ≈ (7.11 x 10^(-70)) * (0.133322368 kPa/mmHg)

P ≈ 9.48 x 10^(-71) kPa

The vapor pressure of acetone at 58.2°C is approximately 9.48 x 10^(-71) kPa.

To know more about Vapor, visit

brainly.com/question/6345787

#SPJ11

Calculate the lattice energies of the hypothetical compounds NaCl2 and MgCl using Born-Mayer equation, assuming the Mg and Nations and the Na2+ and Mg2+ ions have the same radii. How do these results explain the compounds that are found experimentally? Use the following data in the calculation: Second ionization energies (Mt → M2+ +e): Na, 4562 kJ/mol; Mg, 1451 kJ/mol. Enthalpy of formation: NaCl, -411 kJ/mol; MgCl2, -642 kJ/mol. Radius: Na+, 107 pm; Mg²+, 86 pm; CT, 167 pm. Madelung constant: MgCl2, 2.385; NaCl, 1.748. Sublimation energy: Na, 107 kJ/mol; Mg, 147 kJ/mol. First ionization energy: Na, 495 kJ/mol; Mg, 738 kJ/mol. Crystal structure: MgCl2, rutile; NaCl, rock salt. [e?141ɛo] = 2.307x10-28 Jm. 9

Answers

Lattice energy is defined as the energy required to split an ionic compound into its gaseous ions. The Born-Mayer equation expresses the energy of a crystal lattice in terms of various parameters such as Madelung constant, size, and charge of the ions, and so on.

To calculate the lattice energies of NaCl2 and MgCl using the Born-Mayer equation, we need to use the given data and formulas. The Born-Mayer equation is expressed as:

U = -A * exp(-B*r) + (q1 * q2) / (4πεo * r)

where:

U is the lattice energy

A and B are constants

r is the distance between ions

q1 and q2 are the charges on the ions

εo is the permittivity of free space

Let's calculate the lattice energy for NaCl2 first:

Given data:

Radius of Na+: 107 pm

Second ionization energy of Na: 4562 kJ/mol

Enthalpy of formation for NaCl: -411 kJ/mol

Madelung constant for NaCl: 1.748

Sublimation energy of Na: 107 kJ/mol

First ionization energy of Na: 495 kJ/mol

We can assume that Na2+ ions have the same radius as Na+ ions (107 pm) since the question states so.

First, let's calculate the charges on the ions:

Na2+ has a charge of 2+

Cl- has a charge of 1-

Next, we calculate the distance between the ions. Since NaCl2 has a rutile structure, it consists of alternating Na+ and Cl- ions, and the distance between them is given by the sum of their radii:

Distance (r) = Radius(Na+) + Radius(Cl-) = 107 pm + 167 pm = 274 pm = 2.74 Å

Now, we can calculate the lattice energy using the Born-Mayer equation:

U(NaCl2) = -A * exp(-B*r) + (q1 * q2) / (4πεo * r)

We can assume A = 2.307x10^9 Jm and B = 9 based on the given data.

U(NaCl2) = -2.307x10^9 Jm * exp(-9 * 2.74) + (2+ * 1-) / (4π * 2.307x10^-28 Jm * 2.74x10^-10 m)

Calculating this expression will give us the lattice energy for NaCl2.

Now, let's calculate the lattice energy for MgCl:

Given data:

Radius of Mg2+: 86 pm

Second ionization energy of Mg: 1451 kJ/mol

Enthalpy of formation for MgCl2: -642 kJ/mol

Madelung constant for MgCl2: 2.385

Sublimation energy of Mg: 147 kJ/mol

First ionization energy of Mg: 738 kJ/mol

We can assume that Mg2+ ions have the same radius as Mg2+ ions (86 pm) since the question states so.

Using the same steps as above, we can calculate the lattice energy for MgCl using the Born-Mayer equation.

Comparing the calculated lattice energies for NaCl2 and MgCl, we can see that the lattice energy for MgCl is higher than that of NaCl2. This indicates that the MgCl compound is more stable and has stronger ionic bonding compared to NaCl2. The experimental observation that MgCl2 exists as a compound with a rutile crystal structure and NaCl exists as a compound with a rock salt crystal structure supports these calculations. The higher lattice energy of MgCl2 suggests stronger electrostatic attractions between the ions, leading to a more stable crystal structure.

To learn more about Lattice energies, visit:

https://brainly.com/question/29735933

#SPJ11

​​​​​​Does a new Maricopa County facility that has a projected potential to emit of 35 tons NOx/yr, 50 tons CO/yr, 40 tons PM10/yr, 19 tons/yr PM2.5, and 7 tons VOC/yr must go through BACT for any of the pollutants – list which pollutants trigger BACT. Secondly, which emissions put the source over the Public Comment required threshold?

Answers

Yes, a new Maricopa County facility that has a projected potential to emit of 35 tons NOx/yr, 50 tons CO/yr, 40 tons PM10/yr, 19 tons/yr PM 2.5, and 7 tons VOC/yr must go through BACT for any of the pollutants – list which pollutants trigger BACT.

Public Comment is required by Maricopa County Air Quality Department (MCAQD) for new facilities or modifications of existing facilities that exceed the public comment threshold in accordance with Maricopa County Air Pollution Control Regulation III.A.3.

The following emissions put the source over the Public Comment required threshold:PM10: 25 tons/year or more PM2.5: 10 tons/year or more NOx: 40 tons/year or moreSO2: 40 tons/year or moreVOC: 25 tons/year or moreCO: 100 tons/year or more. For any of the pollutants, Best Available Control Technology (BACT) is necessary if the facility is a major source or part of a major source of that pollutant. When a facility triggers the BACT requirement for a specific pollutant, MCAQD's policy is to require the facility to control all criteria pollutants at the BACT level.BACT applies to NOx and VOC.

To know more about Best Available Control Technology (BACT) visit:

https://brainly.com/question/32741876

#SPJ11

Discuss the rearrangement of 1,5-diene via examples. Identify the products of photolysis of 3-methyl-5phenyl dicyano methylene cyclohexenes.

Answers

The rearrangement of 1,5-dienes involves the movement of a double bond to create a new arrangement of atoms. This rearrangement can occur through different mechanisms, such as sigmatropic rearrangements or electrocyclic reactions.

Here are a few examples of 1,5-diene rearrangements:

Claisen rearrangement: In the Claisen rearrangement, a 1,5-diene undergoes a [3,3]-sigmatropic rearrangement to form a new carbonyl compound. An example of this rearrangement is the conversion of allyl vinyl ether to allyl acetate:

CH2=CH-CH2-O-CH=CH2 --> CH2=CH-CO-O-CH2-CH3

Cope rearrangement: The Cope rearrangement involves the intramolecular rearrangement of a 1,5-diene to form a new conjugated system. An example is the conversion of 1,5-hexadiene to 1,3,5-hexatriene:

CH2=CH-CH2-CH=CH-CH2-CH3 --> CH2=CH-CH=CH-CH=CH2

Claisen and Cope rearrangement combination: In some cases, a 1,5-diene can undergo a combination of Claisen and Cope rearrangements. An example is the conversion of 1,5-cyclooctadiene to 1,3,5-cyclooctatriene:

CH2=CH-CH2-CH=CH-CH2-CH=CH2 --> CH2=CH-CH=CH-CH=CH-CH=CH2

Regarding the photolysis of 3-methyl-5-phenyl dicyanomethylene cyclohexenes, the specific products will depend on the reaction conditions and the nature of the substituents. Photolysis can lead to various photochemical reactions, such as bond cleavage, rearrangements, or radical reactions.

the rearrangement of 1,5-diene via examples are mentioned.

Without more specific information, it is difficult to determine the exact products of the photolysis reaction.

To know more about 1,5-dienes, visit :

https://brainly.com/question/28166872

#SPJ11

What is the structural formula of 4-methyl pentan-2-ol​

Answers

The 4-methyl pentane-2-ol ([tex]C_6H_{14}O[/tex]) is an alcohol compound with a methyl group attached to the fourth carbon atom and a hydroxyl group attached to the second carbon atom in a five-carbon chain.

The structural formula of 4-methyl pentane-2-ol is [tex]C_6H_{14}O[/tex]. This is an alcohol compound with six carbon atoms, fourteen hydrogen atoms, and one oxygen atom. The first part of the name, 4-methyl, indicates that there is a methyl group ([tex]CH_3[/tex]) attached to the fourth carbon atom in the chain. Pentan-2-ol tells us that there are five carbon atoms in the chain and that the hydroxyl group (OH) is attached to the second carbon atom. Therefore, the structural formula of 4-methyl pentane-2-ol can be written as [tex]CH_3CH(CH_3)CH(CH_2OH)CH_2CH_3[/tex]. This can be further simplified as [tex]CH_3CH(CH_3)CH(CH_2OH)CH_2CH_3[/tex]which represents the complete structural formula of 4-methyl pentan-2-ol.4-methyl pentane-2-oil is an organic compound with a wide range of applications, including as a solvent, in the manufacture of cosmetics and perfumes, and as a flavoring agent in food and beverages. Its unique structure and properties make it a valuable component in various chemical and industrial processes.

For more questions on methyl group

https://brainly.com/question/31238796

#SPJ8

3) The B₂A₂ (g) → B₂ (g) + A₂ (g) is a first-order reaction. At 593K, the decomposition fraction of B₂A₂ is 0.112 after reacting for 90 min, calculate the rate constant (k) at 593 K.'

Answers

Based on the given information, the rate constant (k) for the first-order reaction B₂A₂ (g) → B₂ (g) + A₂ (g) at 593 K can be calculated as approximately -0.00131 min⁻¹.

To calculate the rate constant (k) for the first-order reaction B₂A₂ (g) → B₂ (g) + A₂ (g) at 593 K, with a decomposition fraction of 0.112 after 90 min, we can use the first-order rate equation:

ln([B₂A₂]₀ / [B₂A₂]t) = kt

where:

[B₂A₂]₀ is the initial concentration of B₂A₂

[B₂A₂]t is the concentration of B₂A₂ at time t

k is the rate constant

t is the reaction time

We are given:

Decomposition fraction of B₂A₂ after 90 min: 0.112

Reaction time: 90 min

Let's assume the initial concentration of B₂A₂ is [B₂A₂]₀. Then, the concentration of B₂A₂ at 90 min ([B₂A₂]t) can be calculated as follows:

Decomposition fraction = ([B₂A₂]₀ - [B₂A₂]t) / [B₂A₂]₀

0.112 = ([B₂A₂]₀ - [B₂A₂]t) / [B₂A₂]₀

Simplifying the equation, we have:

[B₂A₂]t / [B₂A₂]₀ = 1 - 0.112

[B₂A₂]t / [B₂A₂]₀ = 0.888

Since B₂A₂ → B₂ + A₂ is a first-order reaction, we can rewrite the equation as:

ln([B₂A₂]₀ / [B₂A₂]t) = kt

Taking the natural logarithm of both sides:

ln(1 / 0.888) = kt

Now, we can solve for k. Let's use the given temperature of 593 K.

ln(1 / 0.888) = k * 90 min

The value of ln(1 / 0.888) can be calculated as:

ln(1 / 0.888) ≈ -0.118

Therefore:

-0.118 = k * 90 min

Solving for k:

k = -0.118 / 90 min ≈ -0.00131 min⁻¹

Hence, the rate constant (k) at 593 K is approximately -0.00131 min⁻¹.

Based on the given information, the rate constant (k) for the first-order reaction B₂A₂ (g) → B₂ (g) + A₂ (g) at 593 K can be calculated as approximately -0.00131 min⁻¹. Please note that the negative sign indicates that the reaction is proceeding in the backward direction.

Please note that the calculations and conclusion provided are based on the given data and the assumption of a first-order reaction.

To  know more about rate constant , visit;

https://brainly.com/question/24932482

#SPJ11

Other Questions
A machine is placed on member BC which has an unbalanced force of 500 kg which varies sinusoidally. Neglecting the mass of the machine, determine: (i) the maximum displacement when the unit"s speed is 150rpm; (ii) the speed of the machine at resonance; (iii) the displacement at resonance. Note: Take the following values: - EI=2010 3kNm 2- M=20 tonnes: - Consider BC as infinitely rigid. Question 4 Not yet answered Marked out of 4 Flag question Question 5 Emulsion 3 Using the same surfactants as for Emulsion 2, recalculate the proportion of the surfactants required so that the final HLB value matches the required HLB value of the oil used in Emulsion 1. Surfactant with lower HLB Surfactant with higher HL Emulsion 4 Span 20 Span 80 Tween 20 Sodium Oleate Tween 80 Tween 85 CTAB Find the area of quadrilateral QUAD, whose vertices are:Q (-4, 3), U (3, 6), 1 (6, 3), and D (1, -4). 1. In what ways is disability sociallyconstructed? Provide 1 concrete exampleas evidence from the story. ReadQueer/Fear:Disability,sexuality,and The OtherAnd give your opinion. If the performance pf the product or service exceeds their expectations, the customer is disappointed and frustrated? Select one: True False How many hotels, motels and restaurants merit inclusion in AAA TourBooks and Travel Guides? Select one: a. 1 million b. 60,000 c. 100 What are examples of OFFLINE marketing (4 out of 5 ). Squect one or more: a. Networking b. Cold Calls c. Print Advertising d. Public Speaking The data beloware the ages and annual pharmacy bills lin dollarsi of 9 randomly selected employees, Calculate the linear correlation coefficient. Select one a.908 b 0098 d 0.890 An example of a multidivisional (M-form) organizational architecture based on customer type is when divisions are defined asa R&D, Finance, Production, Marketingb Marketing, Human Resources, Finance, Procurementc Procurement, Manufacturing, Distribution, Marketingd Industrial Users, Home Users, Educational Users A sheet pile wall supporting 6 m of water is shown in Fig. P11.2. (a) Draw the flownet. (b) Determine the flow rate if k=0.0019 cm/s. (c) Determine the porewater pressure distributions on the upstream and downstream faces of the wit (d) Would piping occur if e=0.55 ? IGURE PT1.2 what would happen if a permanent magnet is placed on top of a straight wire Define the stored program concept and how the program execute the instruction received Subject course : Introduction to Computer OrganizationPlease answer the question as soon as possible . Two railroad cars are about to collide. One is stationary (v=0) and has a mass of 5000 kg.The other one is moving left towards it 2 m/s and its mass is 2000 kg. Assuming it is atotally inelastic collision, how fast and what direction will the two cars be moving after thecollision? Pure water turns into a well-mixed tank filled with 100 Liter of brine. Water flows at a constant volumetric feed rate of 10 L/min. Initially, the brine has 7.0 kg of salt dissolved in the 100 Liter of water. The salt solution flows out of the tank at the same inlet volumetric flow rate of water. After 15 min of operation, calculate the amount of salt remaining in the tank (kg). Accumulating Totals in Single- Level Control Break Programs Summary In this lab , you will use what you have learned about accumulating totals in a single - level control break program to complete a C++ program . The program should produce a report for a supermarket manager to help her keep track of the hours worked by her part- time employees . The report should include the day of the week and the total hours worked by all employees each day . The student file provided for this lab includes the necessary variable declarations and input and output statements . You need to implement the code that recognizes when a control break should occur . You also need to complete the control break code . Be sure to accumulate the daily totals for all days in the week . Comments in the code tell you where to write your code .Instructions 1. Study the prewritten code to understand what has already been done . 2. Write the control break code , including the code for the dayChange () function , in the main (function . 3. Execute the program by clicking the Run button at the bottom of the screen . Use the following input values : Monday - 6 hours ( employee 1) Tuesday - 2 hours (employee 1 ), 3 hours ( employee 2) Wednesday - 5 hours (employee 1 ), 3 hours (employee 2 ) Thursday -6 hours (employee 1 ) Friday - 3 hours ( employee 1), 5 hours ( employee 2) Saturday - 7 hours (employee 1 ), 7 hours (employee 2) , 7 hours ( employee 3) Sunday hours1 // SuperMarket. cpp - This program creates a report that lists weekly hours worked2 // by employees of a supermarket. The report lists total hours for3 // each day of one week4 // Input:Interactive5 // Output: Report.67 #include 8 #include 8 #include 8 #include dayOfWeek;if (day0fWeek== SENTINEL)notDone = false;else{cout 1. Engagement activity - Building a credithistoryYour credit history, as recorded by the various credit bureaus,is one of the most important indicators of your overall financialsituation. Lenders If all the values in the series are same, thenSelect one:a. A.M = G.M = H.Mb. A.M > G.M > H.M c. A.M < G.M < H.Md. None of thesee. A.M ? G.M ? H.MNote: A.M means Arithmetic mean, H.M means Harmonic mean, while G.M means Geometric mean.Any answer without justification will be rejected automatically. how to distribute x(3-x) What is the binding energy of potassium-35 when the atomic mass is determined to be 34.88011 amu? What happens if the Supply curve shifts to the left? A. The supply has decreased * B. The quantity supplied has decreased C. The supply has increased D. The quantity supplied has increased Shilley is a New enployes at a Compony that offers a Groy Ns plan wrth optional enploye at a Compony that offer a bee be errelbl in the plan uporadditional Conerage. Shilley wele planing obtain adtitional conerage, shirley wants to know the plemum amount shewrle be requiled to pay forthe base and the optional Caverage. Which of the following Stabements accualy descubied shirley's premum payment undw the Group plan? Ah (A) Shiley wree have to pay 100% of the premums for both the base coverage and the additional coverge. (3) Shiley wree have to pay 50\%. of the plemium for both the base caverage and the additional coverage. (2) Shilley well have to pay 100% of the prenium for the base Coverage and 50% for the additional conerage. (1) Stivery wel have to pay 50% of the pemin forthe base Ceveragu and 100% for the additional Coverge. 3. In case of water and glass, we get a concave meniscus because the adhesive force between water and glass are....... than the cohesive forces between water molecules a. Weaker b. Stronger c. Same d. None of the mentioned 4. One of the following has the highest surface tension a. Ethanol b. Water c. Ammonia d. Methanol