2. An ideal gas is compressed isothermally and reversibly at 400K from 1 m³ to 0.5 m³. 9200 J heat is evolved during compression. What is the work done and how many moles of (2.5 marks) gas were compressed during this process?

Using Adams's method with d = 16 to apportion the new officers among the precincts as Precinct A: 39 officers, Precinct C: 47 officers, Precinct D: 20 officers, Precinct E: 29 officers, Precinct F: 39 officers.

To apportion the 175 new officers among the six precincts using Adams's method with d = 16, we need to follow these steps:

1. Calculate the crime ratios for each precinct by dividing the number of crimes by the square root of the number of officers already assigned to that precinct.
  - Precinct A: Crime ratio = 436 / √(16) = 109
  - Precinct C: Crime ratio = 522 / √(16) = 131
  - Precinct D: Crime ratio = 218 / √(16) = 55
  - Precinct E: Crime ratio = 324 / √(16) = 81
  - Precinct F: Crime ratio = 433 / √(16) = 108

2. Calculate the total crime ratio by summing up the crime ratios of all precincts.
  Total crime ratio = 109 + 131 + 55 + 81 + 108 = 484

3. Calculate the apportionment for each precinct by multiplying the total number of officers (175) by the crime ratio for each precinct, and then dividing it by the total crime ratio.
  - Precinct A: Apportionment = (175 * 109) / 484 = 39 officers
  - Precinct C: Apportionment = (175 * 131) / 484 = 47 officers
  - Precinct D: Apportionment = (175 * 55) / 484 = 20 officers
  - Precinct E: Apportionment = (175 * 81) / 484 = 29 officers
  - Precinct F: Apportionment = (175 * 108) / 484 = 39 officers

So, according to Adams's method with d = 16, the new officers should be apportioned as follows:
- Precinct A: 39 officers
- Precinct C: 47 officers
- Precinct D: 20 officers
- Precinct E: 29 officers
- Precinct F: 39 officers

This apportionment aims to allocate the officers in a way that takes into account the crime rates of each precinct relative to their existing officer counts.

Learn more about the Adams's method from the given link-

https://brainly.com/question/32735598

#SPJ11

There is no external force or moment acting at G. Therefore, the force acting on GD should pass through G.

The force in member GD is equal to the sum of the forces acting at joint D and G.

Given: P1​=2000lb and P2​=500lbThe free-body diagram of the truss is shown in the figure below: Free body diagram of the truss As the truss is in equilibrium, therefore, the algebraic sum of the horizontal and vertical forces on each joint is zero.

By resolving forces horizontally, we get; F_C_E = P_1/2 = 1000lbF_C_D = F_E_F = P_2 = 500lbAs both the forces are acting away from the joints, therefore, members CE and EF are in tension and member CD is in compression. Why the force acting at the pin G is directed along member GD.

The force acting at the pin G is directed along member GD as it is collinear to member GD.

Moreover, By resolving the forces at joint D, we get; F_C_D = F_D_G × cos 45°F_D_G = F_C_D / cos 45° = 500/0.707 = 706.14lb.

Now, resolving the forces at joint G;F_G_D = 706.14 lb Hence, the force in member GD is 706.14 lb.

To know more about diagram visit:

https://brainly.com/question/13480242

#SPJ11

As the upper bound of the 97.5% confidence interval is greater than 45, there is not enough evidence to conclude that the mean time is less than 45 minutes.

The sample mean, the sample standard deviation and the sample size are given as follows:

[tex]\overline{x} = 43.75, s = 4, n = 36[/tex]

The critical value, using a t-distribution calculator, for a two-tailed 97.5% confidence interval, with 36 - 1 = 35 df, is t = 2.342.

Then the upper bound of the interval is given as follows:

43.75 + 2.342 x 4/6 = 45.3 months.

More can be learned about the t-distribution at https://brainly.com/question/17469144

#SPJ4

Among the given options, alkynes I and II will be deprotonated with NaNH2.The given statement can be explained as follows Deprotonation is a type of chemical reaction that occurs when a proton (a hydrogen ion) is removed from a molecule, ion, or other compound.

Strong bases, such as NaNH2, are commonly used to deprotonate alkynes.The following alkynes are given Deprotonation of the first alkyne, CH3C≡CH can occur using NaNH2.The following is the balanced chemical equation for the reaction ..

The second alkyne, C6H5C≡CH, will also undergo deprotonation using NaNH2.The following is the balanced chemical equation for the reaction:C6H5C≡CH + NaNH2 → C6H5C=N-Na+ + NH3 + H2Thus, among the given options, alkynes I and II will be deprotonated with NaNH2. Hence, the correct answer is "I and II".

To know more about deprotonated visit :

https://brainly.com/question/30706409

#SPJ11

The 71st percentile of the data set (27, 34, 15, 20, 25, 30, 28, 25) is 30.

To find the 71st percentile in the given data set (27, 34, 15, 20, 25, 30, 28, 25), we first need to arrange the data in ascending order: 15, 20, 25, 25, 27, 28, 30, 34.

Next, we calculate the rank of the 71st percentile using the formula:

Rank = (P/100) * (N + 1)

where P is the desired percentile (71) and N is the total number of data points (8).

Substituting the values, we have:

Rank = (71/100) * (8 + 1)

= 0.71 * 9

= 6.39

Since the rank is not an integer, we round it up to the nearest whole number. The 71st percentile corresponds to the value at the 7th position in the ordered data set.

The 7th value in the ordered data set (15, 20, 25, 25, 27, 28, 30, 34) is 30.

Therefore, the 71st percentile of the given data set is 30.

To learn more about ordered data sets visit : https://brainly.com/question/30154121

#SPJ11

23) The correct answer is "d) All the above."

24) The correct answer is "c) A, b, and other."

25) The correct answer is "c) A, b, and other."

26) The correct answer is "c) All of the above."

27) The correct answer is "c) A, b, and other."

28) The correct answer is "c) A, b, and other."

23: The different "lives" of construction equipment refer to various ways of looking at the lifespan and value of the equipment. The actual life of construction equipment refers to the physical lifespan of the equipment, considering factors such as wear and tear, maintenance, and repairs. The depreciable life of construction equipment is the period over which the equipment's value decreases, typically for accounting and tax purposes. The economic life of construction equipment refers to the period during which the equipment remains economically useful and cost-effective to operate. So, the correct answer is "d) All the above."

24: Decisions in various situations can be made using different factors. Tons of data can be analyzed to make informed decisions. People's input, expertise, and opinions are also valuable when making decisions. Additionally, other factors such as market trends, regulations, and financial considerations can influence decision-making. So, the correct answer is "c) A, b, and other."

25: Personal management skills are essential for effectively managing oneself and interacting with others. Communication skills are necessary for effectively expressing ideas, listening, and understanding others. Negotiation skills are important for resolving conflicts, reaching agreements, and achieving mutually beneficial outcomes. Other personal management skills may include time management, problem-solving, decision-making, and leadership skills. So, the correct answer is "c) A, b, and other."

26: Time management is crucial for managers, and they need to allocate their time effectively to various tasks and responsibilities. Family time refers to managing personal and family commitments within a manager's schedule. Boss-imposed time refers to tasks and activities assigned by the manager's superior or boss. Both family time and boss-imposed time are examples of time management considerations for managers. So, the correct answer is "c) All of the above."

27: Project managers have various functions related to managing project resources. Leading involves guiding and directing the project team towards the project's goals and objectives. Motivating involves inspiring and encouraging the project team to perform at their best. Other PM functions related to project resources may include resource allocation, training and development, performance management, and conflict resolution. So, the correct answer is "c) A, b, and other."

28: Stakeholder management is an important process in project management. Ignoring stakeholders can lead to negative consequences for the project. Communicating with stakeholders is essential for keeping them informed, addressing their concerns, and obtaining their support. Other actions in stakeholder management may include identifying stakeholders, assessing their needs and expectations, engaging them in decision-making, and managing relationships with them throughout the project. So, the correct answer is "c) A, b, and other."

To learn more about management

https://brainly.com/question/15144960

#SPJ11

The maximum length of the mesiodistal crown of mandibular first molars during weeks 30 through 60 is mm (rounded to three decimal places).

The given function represents the relationship between the mesiodistal crown length (L) of deciduous mandibular first molars and the post-conception age of the tooth (t) in weeks. To find the maximum length within the specified range of 30 to 60 weeks, we need to determine the vertex of the quadratic function L(t) = -0.015t² + 1.44t - 7.7.

The vertex of a quadratic function is given by the formula t = -b / (2a), where a, b, and c are the coefficients of the quadratic equation in standard form (ax² + bx + c).

In this case, the coefficients are:

a = -0.015

b = 1.44

Using the formula, we can find the vertex:

t = -1.44 / (2 * -0.015) = 48

Therefore, the maximum length occurs at t = 48 weeks. To find the maximum length, we substitute this value into the function:

L(48) = -0.015(48)² + 1.44(48) - 7.7

Calculating the value, we find the maximum length in millimeters.

Therefore, the correct choice is: The maximum length is mm (rounded to three decimal places).

Learn more about functions: brainly.com/question/11624077

#SPJ11

The maximum length of the mesiodistal crown of mandibular first molars during weeks 30 through 60 is mm (rounded to three decimal places).

The given function represents the relationship between the mesiodistal crown length (L) of deciduous mandibular first molars and the post-conception age of the tooth (t) in weeks. To find the maximum length within the specified range of 30 to 60 weeks, we need to determine the vertex of the quadratic function L(t) = -0.015t² + 1.44t - 7.7.

The vertex of a quadratic function is given by the formula t = -b / (2a), where a, b, and c are the coefficients of the quadratic equation in standard form (ax² + bx + c).

In this case, the coefficients are:

a = -0.015

b = 1.44

Using the formula, we can find the vertex:

t = -1.44 / (2 * -0.015) = 48

Therefore, the maximum length occurs at t = 48 weeks. To find the maximum length, we substitute this value into the function:

L(48) = -0.015(48)² + 1.44(48) - 7.7

Calculating the value, we find the maximum length in millimeters.

Therefore, the correct choice is: The maximum length is mm (rounded to three decimal places).

Learn more about functions: brainly.com/question/11624077

#SPJ11

The abbreviation SS stands for Suspended Solids. In the context of water and the mixed liquor of the activated sludge aeration tank, SS has significant importance.

In water, suspended solids refer to particles that are present but are not dissolved. These can include organic matter, inorganic matter, and microorganisms. The presence of suspended solids in water can have several implications. Firstly, high levels of suspended solids can cause water to appear cloudy or turbid, reducing its aesthetic quality. Secondly, suspended solids can interfere with various processes such as filtration, disinfection, and chemical treatment. For example, suspended solids can clog filters and reduce their efficiency.

In the mixed liquor of the activated sludge aeration tank, suspended solids play a crucial role in wastewater treatment. The mixed liquor is a combination of wastewater and microorganisms that actively consume organic matter. Suspended solids in the mixed liquor provide a surface area for microorganisms to attach and grow. These microorganisms, often referred to as activated sludge, play a key role in breaking down organic matter in the wastewater. The microorganisms consume the organic matter, converting it into carbon dioxide, water, and more microorganisms. The suspended solids in the mixed liquor help to create a large population of microorganisms, ensuring effective treatment of the wastewater.

Overall, the significance of SS in water and in the mixed liquor of the activated sludge aeration tank lies in their impact on water quality and the treatment of wastewater. Suspended solids can affect water clarity, interfere with treatment processes, and facilitate the breakdown of organic matter in wastewater.

Know more about Suspended Solids here:

https://brainly.com/question/32376032

#SPJ11

The probability that Tamika draws a strawberry-flavored candy is 1/4.

The probability that Tamika draws a strawberry-flavored candy can be calculated by dividing the number of strawberry-flavored candies by the total number of candies in the pack.

Since each pack contains 4 flavors and there are even numbers of all flavors, we can assume that each flavor appears the same number of times.

Therefore, there are 20/4 = 5 candies of each flavor in the pack.

So, the number of strawberry-flavored candies is 5.

The total number of candies in the pack is given as 20.

To calculate the probability, we divide the number of strawberry-flavored candies by the total number of candies:

Probability = Number of strawberry-flavored candies / Total number of candies

Probability = 5 / 20

Simplifying the fraction, we get:

Probability = 1 / 4

Therefore, the probability that Tamika draws a strawberry-flavored candy is 1/4.

Learn more about probability from this link:

https://brainly.com/question/13604758

#SPJ11

The direction vector of the line is given by:![d= 3i + 2j + 4k \label{d}\]Thus, d = <3, 2, 4>Step 2: Find the normal vector of the plane by taking the cross product of the direction vector and another vector on the plane.

To find the equation of the plane that passes through the point (1, 2, 3) and perpendicular to the line x + 2y + 3z - 2 = 0 and 3x + 2y + 4z = 0,

we use the following steps:Step 1: Find the direction vector of the line using the coefficients of the line equation.

To find another vector on the plane, we pick two points on the line, which lie on the plane, say P(1, 2, 3) and Q(0, -1, -2). Then, we take the vector PQ, which is given by:[tex]![PQ = <1 - 0, 2 - (-1), 3 - (-2)> = <1, 3, 5>[/tex]\]Then, the normal vector of the plane is given by:![n = d \times PQ = \begin{vmatrix}\hat{i} & \hat{j} & \hat{k} \\3 & 2 & 4\\ 1 & 3 & 5\end{vmatrix} = 2\hat{i} - 14\hat{j} + 8\hat{k}\]

Thus, n = <2, -14, 8>Step 3: Use the point-normal form to find the equation of the plane.The point-normal form of the equation of the plane is given by:![n \cdot (r - P) = 0 \label{eq:point-normal}\]where n is the normal vector of the plane, P is the given point on the plane (1, 2, 3), and r is a point on the plane.

Substituting the values into the equation gives:![<2, -14, 8> \cdot ( - <1, 2, 3>) = 0 \label{eq:plane}\]Simplifying the equation gives:[tex]![2(x-1) - 14(y-2) + 8(z-3) = 0\][/tex]

Therefore, the equation of the plane is given by 2(x-1) - 14(y-2) + 8(z-3) = 0.

To know more about equation visit:

https://brainly.com/question/33433874

#SPJ11

The enthalpy change for the reaction 2M(s) + 3Cl₂(g) -> 2MCl₃(s) is -2740.2 kJ.

The enthalpy change for the reaction can be determined by considering the enthalpy changes of the individual steps involved.

First, we can use the given enthalpy change for the reaction 2M(s) + 6HCl(aq) -> 2MCl₃(aq) + 3H₂(g) (-ΔH₁ = -720.0 kJ) to write the overall reaction as 2M(s) + 6HCl(aq) -> 2MCl₃(s) + 3H₂(g) (-ΔH₁ = -720.0 kJ).

Next, we can use the given enthalpy change for the reaction HCl(g) -> HCl(aq) (-ΔH₂ = -74.8 kJ) to write the overall reaction as 2M(s) + 6HCl(aq) -> 2MCl₃(s) + 3H₂(g) + 3HCl(aq) (-ΔH₁ + ΔH₂ = -794.8 kJ).

Finally, we can use the given enthalpy change for the reaction 3HCl(aq) -> 3HCl(g) (-ΔH₃ = -310.0 kJ) to write the overall reaction as 2M(s) + 6HCl(aq) -> 2MCl₃(s) + 3H₂(g) + 3HCl(g) (-ΔH₁ + ΔH₂ - ΔH₃ = -1104.8 kJ).

Since the reaction is balanced as written, the enthalpy change for the reaction 2M(s) + 3Cl₂(g) -> 2MCl₃(s) is equal to the sum of the enthalpy changes of the individual steps, which gives us -ΔH₁ + ΔH₂ - ΔH₃ = -1104.8 kJ.

Learn more about enthalpy change

brainly.com/question/1477087

#SPJ11

1.84.20 grams of silver chloride will be produced.

CaCl₂ is the limiting reactant.

2. This is a double displacement reaction or metathesis reaction.

1. To determine how many grams of silver chloride will be produced, we need to first calculate the moles of each reactant. The molar mass of silver nitrate (AgNO₃) is 169.87 g/mol, and the molar mass of calcium chloride (CaCl₂) is 110.98 g/mol. Using the given masses, we can calculate the moles of each reactant:

- Moles of AgNO₃ = 100.0 g / 169.87 g/mol = 0.588 mol

- Moles of CaCl₂ = 100.0 g / 110.98 g/mol = 0.901 mol

From the balanced equation, we see that the ratio of moles of AgNO₃ to AgCl is 2:2, meaning that 1 mol of AgNO₃ produces 1 mol of AgCl. Therefore, the moles of AgCl produced will be equal to the moles of AgNO₃. To find the mass of AgCl produced, we multiply the moles of AgCl by its molar mass (143.32 g/mol):

- Mass of AgCl = 0.588 mol * 143.32 g/mol = 84.20 g

Therefore, 84.20 grams of silver chloride will be produced.

To determine the limiting reactant, we compare the moles of each reactant to their stoichiometric ratio in the balanced equation. The ratio of AgNO₃ to CaCl₂ is 2:1. Since we have 0.588 moles of AgNO₃ and 0.901 moles of CaCl₂, we can see that there is an excess of CaCl₂. Therefore, CaCl₂ is the limiting reactant.

2. This reaction is classified as a double displacement or precipitation reaction. In a double displacement reaction, the cations and anions of two compounds switch places, forming two new compounds. In this case, the silver ion (Ag⁺) from silver nitrate (AgNO₃) combines with the chloride ion (Cl⁻) from calcium chloride (CaCl₂) to form silver chloride (AgCl), and the calcium ion (Ca²⁺) from calcium chloride combines with the nitrate ion (NO₃⁻) from silver nitrate to form calcium nitrate (Ca(NO₃)₂). The formation of a solid precipitate (AgCl) indicates a precipitation reaction.

Know more about  double displacement reaction

https://brainly.com/question/29740109

#SPJ11

1. 84.20 grams of silver chloride will be produced.

CaCl₂ is the limiting reactant.

2. This is a double displacement reaction or metathesis reaction.

1. To determine how many grams of silver chloride will be produced, we need to first calculate the moles of each reactant.

The molar mass of silver nitrate (AgNO₃) is 169.87 g/mol, and the molar mass of calcium chloride (CaCl₂) is 110.98 g/mol.

Using the given masses, we can calculate the moles of each reactant:

- Moles of AgNO₃ = 100.0 g / 169.87 g/mol = 0.588 mol

- Moles of CaCl₂ = 100.0 g / 110.98 g/mol = 0.901 mol

From the balanced equation, we see that the ratio of moles of AgNO₃ to AgCl is 2:2, meaning that 1 mol of AgNO₃ produces 1 mol of AgCl. Therefore, the moles of AgCl produced will be equal to the moles of AgNO₃.

To find the mass of AgCl produced, we multiply the moles of AgCl by its molar mass (143.32 g/mol):

- Mass of AgCl = 0.588 mol * 143.32 g/mol = 84.20 g

Therefore, 84.20 grams of silver chloride will be produced.

To determine the limiting reactant, we compare the moles of each reactant to their stoichiometric ratio in the balanced equation.

The ratio of AgNO₃ to CaCl₂ is 2:1. Since we have 0.588 moles of AgNO₃ and 0.901 moles of CaCl₂, we can see that there is an excess of CaCl₂. Therefore, CaCl₂ is the limiting reactant.

2. This reaction is classified as a double displacement or precipitation reaction. In a double displacement reaction, the cations and anions of two compounds switch places, forming two new compounds.

In this case, the silver ion (Ag⁺) from silver nitrate (AgNO₃) combines with the chloride ion (Cl⁻) from calcium chloride (CaCl₂) to form silver chloride (AgCl), and the calcium ion (Ca²⁺) from calcium chloride combines with the nitrate ion (NO₃⁻) from silver nitrate to form calcium nitrate (Ca(NO₃)₂).

The formation of a solid precipitate (AgCl) indicates a precipitation reaction.

Know more about double displacement reaction

brainly.com/question/29740109

#SPJ11

Principle of mathematical induction, the statement holds for all integers n ≥ 1 .we have proved that bn = 2n + 1 for each integer n ≥ 1.

Base case

Let's first check if the statement holds for the base case n = 1.

When n = 1, we have b1 = 3. And indeed, 2^1 + 1 = 3. So, the statement holds for the base case.

Inductive step

Assume that the statement holds for some integer k, i.e., assume that bk = 2k + 1.

Now, let's prove that the statement holds for k + 1, i.e., we need to show that b(k+1) = 2(k+1) + 1.

Using the given recursive definition of the sequence, we have:

b(k+1) = 3b(k) - 3b(k-1) - 25(k+1-2)

= 3(2k + 1) - 3(2(k-1) + 1) - 25k

= 6k + 3 - 6k + 3 - 25k

= -19k + 6

= 2(k+1) + 1

So, the statement holds for k + 1.

By the principle of mathematical induction, the statement holds for all integers n ≥ 1.

Therefore, we have proved that bn = 2n + 1 for each integer n ≥ 1.

To know more about integer

https://brainly.com/question/490943

#SPJ11

The mass of Ag₂CO3(s) produced by mixing 130.3 mL of 0.365 M Na₂CO3(aq) and 71.1 mL of 0.216 M AgNO3(aq) is 0.337 g.

To calculate the mass of Ag₂CO3(s) produced, we need to determine the limiting reagent between Na₂CO3 and AgNO3. The limiting reagent is the reactant that is completely consumed and determines the maximum amount of product that can be formed.

First, we need to calculate the number of moles of Na₂CO3 and AgNO3 using their molarity and volume.
For Na₂CO3:
Moles = concentration (M) × volume (L)
Moles = 0.365 mol/L × 0.1303 L = 0.0475 mol

For AgNO3:
Moles = concentration (M) × volume (L)
Moles = 0.216 mol/L × 0.0711 L = 0.0154 mol

Next, we need to determine the stoichiometric ratio between Na₂CO3 and Ag₂CO3. According to the balanced equation, 2 moles of AgNO3 react with 1 mole of Na₂CO3 to produce 1 mole of Ag₂CO3.

Comparing the moles of Na₂CO3 and AgNO3, we can see that there is an excess of Na₂CO3, as 0.0475 mol > 0.0154 mol. Therefore, AgNO3 is the limiting reagent.

Now, we can calculate the moles of Ag₂CO3 produced from the moles of AgNO3:
Moles of Ag₂CO3 = moles of AgNO3 × (1 mole of Ag₂CO3 / 2 moles of AgNO3)
Moles of Ag₂CO3 = 0.0154 mol × (1 mol / 2 mol) = 0.0077 mol

Finally, we can calculate the mass of Ag₂CO3 using its molar mass:
Mass of Ag₂CO3 = moles of Ag₂CO3 × molar mass of Ag₂CO3
Mass of Ag₂CO3 = 0.0077 mol × 275.8 g/mol = 0.337 g.

Therefore, the mass of Ag₂CO3 produced is 0.337 g.

Know more about limiting reagent here:

https://brainly.com/question/31472915

#SPJ11

The activation diameter at 0.3% supersaturation for particles comprising of 50% (NH4)2SO4, 30% NH4NO3, and 20% insoluble material is approximately 0.078 µm.

Activation diameter: The size of particles that can activate cloud droplets at a specific supersaturation is referred to as the activation diameter.

The activation diameter is influenced by factors such as the chemical composition and the atmospheric relative humidity or saturation condition, and it is essential in estimating the number concentration of droplets in clouds.

(NH4)2SO4 and NH4NO3 are the two most abundant atmospheric aerosols, which form secondary organic aerosols (SOAs) from the oxidation of volatile organic compounds.

SOAs are known to be one of the most significant drivers of adverse health outcomes related to air quality.

They contribute to respiratory and cardiovascular diseases and mortality.

Know more about diameter  here:

https://brainly.com/question/30460318

#SPJ11

To calculate the menu price of the item, we need to reverse calculate the amount before sales tax. We know that the total amount paid, including tax, is $21.79.

Subtract the sales tax amount from the total

$21.79 - (5.6% of $21.79) = $20.67

To determine the menu price of the item, we start with the total amount paid, which includes the sales tax. In this case, the total amount paid is $21.79.

To find the menu price, we need to remove the sales tax amount from the total. Since the sales tax is calculated as a percentage of the total, we need to subtract the tax amount from the total.

To calculate the sales tax amount, we multiply the total by the tax rate expressed as a decimal. In this case, the tax rate is 5.6%, which is equivalent to 0.056 as a decimal.

So, the sales tax amount is $21.79 multiplied by 0.056, which equals $1.22 (rounded to two decimal places).

Subtracting the sales tax amount from the total gives us the menu price of the item, which is $20.67.

Learn more about sales tax

brainly.com/question/29442509

#SPJ11

The sizes of the angles a and b are a = 120 and b = 60

From the question, we have the following parameters that can be used in our computation:

The figure

The sum of angle on a line is 180

So we have

a + 60 = 180

Evaluate

a = 120

Next, we have

a + b + 90 + 90 = 360

So, we have

120 + b + 90 + 90 = 360

Evaluate

b = 60

Hence, the sizes of angle a and b are a = 120 and b = 60

Read more about angles at

https://brainly.com/question/31898235

#SPJ1

The pump discharge pressure (pump exit pressure)for pumping methanol from Tank A to Tank B, is 60.44 psi.

To determine the pump discharge pressure in psi (pounds per square inch)

the following information is given:

Pipeline schedule: Schedule 40

Nominal diameter: 3 inches

Flow rate: 250 gpm

Properties of methanol:p = 49.09 lbm/ft³μ

= 0.544 CP

Distance between Tank A and Tank B: 3000 ft

To determine the pump discharge pressure, we will use the Darcy-Weisbach equation.The Darcy-Weisbach equation is used to calculate the pressure drop in a pipe given the pipe diameter, fluid density, fluid viscosity, flow rate, and pipe roughness.

The equation is as follows:

ΔP = (f L ρ V²) / (2 D) + ρ g h

Where:

ΔP = pressure drop in psi (pounds per square inch)f = Darcy friction factor

L = length of the pipe in ftρ = density of the fluid in lbm/ft³

V = velocity of the fluid in ft/s

D = diameter of the pipe in inches

g = acceleration due to gravity in ft/s²

h = height difference between the inlet and outlet of the pipe in ft

The Darcy friction factor can be determined using the Colebrook equation as follows:

1 / √f = -2 log10 ((ε / D) / 3.7 + 2.51 / (Re √f))

Where:ε = roughness height of the pipe in ft

D = diameter of the pipe in ft

Re = Reynolds number of the fluid

Re = (ρ V D) / μFirst, we will calculate the Reynolds number of the fluid:

Re = (ρ V D) / μ

Re = (49.09 lbm/ft³) x (250 gpm x 0.1337 ft³/gal) x (3 in. / 12) / (0.544 CP x 1 lbm/32.174 ft-s)

Re = 3,783.8The pipe is Schedule 40, which has a roughness height of 0.00015 ft.

Therefore,ε / D = 0.00015 ft / (3 in. / 12 / ft) = 0.0005

Substituting into the Colebrook equation and solving for f using an iterative process, we get:f = 0.0245Using this value for f and substituting the other values into the Darcy-Weisbach equation, we get:

ΔP = (f L ρ V²) / (2 D) + ρ g h

ΔP = ((0.0245) x (3000 ft) x (49.09 lbm/ft³) x (250 gpm x 0.1337 ft³/gal)²) / (2 x (3 in. / 12)) + (49.09 lbm/ft³) x (32.174 ft/s²) x (0 ft)ΔP = 60.44 psi

Therefore, the pump discharge pressure is 60.44 psi.

To know more about Weisbach visit :

brainly.com/question/30640818

#SPJ11

In summary, the solution to the heat equation problem is given by the Fourier expansions: u(x,t) = ∑[B_n sin(nπx√5)e^(-n^2π^2t/5)],where B_n can be determined using the initial condition u(x,0) = x - x^3.

To solve the heat equation problem, we will use the method of separation of variables.

Let's assume the solution can be written as u(x,t) = X(x)T(t). Plugging this into the heat equation, we get:

T'(t)X(x) = 5X''(x)T(t)

Dividing both sides by u(x,t), we have:

T'(t)/T(t) = 5X''(x)/X(x)

Now, since both sides depend on different variables, they must be equal to a constant. Let's denote this constant as -λ^2.

So we have two separate ordinary differential equations: T'(t)/T(t) = -λ^2 and 5X''(x)/X(x) = -λ^2.

The first equation gives us T(t) = Ae^(-λ^2t), where A is a constant.

The second equation gives us X''(x) + (λ^2/5)X(x) = 0. Solving this equation, we find that X(x) = Bsin(λx√5) + Ccos(λx√5), where B and C are constants.

To satisfy the boundary conditions, we have X(0) = 0 and X(1) = 0. Plugging these into the equation, we find that C = 0 and λ = nπ/√5, where n is an integer.

Finally, using the Fourier expansion, we can express the solution u(x,t) as an infinite sum:

u(x,t) = ∑[B_n sin(nπx√5)e^(-n^2π^2t/5)]

Using the initial condition, u(x,0) = x - x^3, we can find the coefficients B_n through the Fourier sine series expansion.

Learn more about Fourier expansions from the given link!

https://brainly.com/question/32618698

#SPJ11

The element with the greatest metallic character among oxygen, vanadium, selenium, and strontium is strontium.

Metallic character refers to the tendency of an element to exhibit metallic properties, such as the ability to conduct electricity and heat, malleability, and ductility. Strontium is an alkaline earth metal that is located in Group 2 of the periodic table. Elements in Group 2 are known for their high metallic character. Strontium has a low ionization energy and a low electronegativity, which means that it easily loses electrons to form positive ions.

This characteristic is typical of metals. On the other hand, oxygen is a nonmetal located in Group 16 of the periodic table. Nonmetals tend to have higher ionization energies and electronegativities, making them less likely to exhibit metallic properties. Vanadium is a transition metal located in Group 5 of the periodic table

Learn more about ionization energy at

https://brainly.com/question/21745574

#SPJ11

Absolute maximum: 2304
Absolute minimum: 288

To find the absolute maximum and absolute minimum of the function z = f(x, y) = 14x²-56x + 14y² - 56y on the domain D: x² + y² ≤81, we need to find the critical points and evaluate the function at those points.

First, let's find the critical points by taking the partial derivatives of the function with respect to x and y and setting them equal to zero:

∂f/∂x = 28x - 56 = 0
∂f/∂y = 28y - 56 = 0

Solving these equations, we find that x = 2 and y = 2 are the critical points.

Next, we need to check the boundary of the domain D: x² + y² = 81.

This is a circle with radius 9 centered at the origin.

To do this, we can parameterize the boundary by letting x = 9cos(t) and y = 9sin(t), where t is the parameter ranging from 0 to 2π.

Substituting these values into the function, we get:
z = f(9cos(t), 9sin(t)) = 14(81cos²(t))-56(9cos(t)) + 14(81sin²(t))-56(9sin(t))

Simplifying further, we have:
z = 1296cos²(t) + 1296sin²(t) - 504cos(t) - 504sin(t)

Now, we can find the absolute maximum and absolute minimum of z by evaluating the function at the critical points and on the boundary.

At the critical point (2, 2), we have:
z = f(2, 2) = 14(2)²-56(2) + 14(2)² - 56(2) = 150

Now, we need to evaluate the function on the boundary of the domain.

Substituting x = 9cos(t) and y = 9sin(t) into the function, we have:
z = 1296cos²(t) + 1296sin²(t) - 504cos(t) - 504sin(t)

Since cos²(t) + sin²(t) = 1, we can simplify the function to:
z = 1296 - 504cos(t) - 504sin(t)

To find the maximum and minimum values of z on the boundary, we can use the fact that -1 ≤ cos(t) ≤ 1 and -1 ≤ sin(t) ≤ 1.

Substituting the maximum values, we have:
z ≤ 1296 + 504 + 504 = 2304

Substituting the minimum values, we have:
z ≥ 1296 - 504 - 504 = 288

Therefore, the absolute maximum of the function is 2304 and the absolute minimum is 288.

To summarize:
Absolute maximum: 2304
Absolute minimum: 288

Learn more about critical points from this link:

https://brainly.com/question/30459381

#SPJ11

If the original length of the bar was 1 meter (100 cm), it would deform by 0.0267 mm under the force of 'F'.

The unit shape of a bar refers to the change in dimensions of the bar when subjected to a force. In this case, we have a steel bar with a length of 60 cm that has been deformed by 160 μm under the force of 'F'.

To determine the unit shape of this bar, we need to calculate the strain. Strain is a measure of how much an object deforms when subjected to an external force. It is calculated as the change in length divided by the original length.

In this case, the change in length is 160 μm (or 0.16 mm) and the original length is 60 cm (or 600 mm).

Strain = Change in length / Original length

Strain = 0.16 mm / 600 mm

Strain = 0.000267

The unit shape of the bar is given by the strain. It represents the change in length per unit length. In this case, the unit shape of the bar is 0.000267, which means that for every unit length of the bar, it deforms by 0.000267 units.

To clarify, if the original length of the bar was 1 meter (100 cm), it would deform by 0.0267 mm under the force of 'F'.

It's important to note that the Elastic Modulus of Steel is 200 GPa. This is a measure of the stiffness of a material. The higher the modulus, the stiffer the material. The Elastic Modulus is used to calculate stress, which is a measure of the internal resistance of a material to deformation.

In summary, the unit shape of the steel bar, which is the change in length per unit length, is 0.000267. This means that for every unit length of the bar, it deforms by 0.000267 units.

Know more about Elastic Modulus

https://brainly.com/question/30756002

#SPJ11

The correct answer is Option B.10 . The constant of variation for this relation is k=10.

When two variables are directly proportional, they are related by the equation y=kx, where k is the constant of variation.

This means that as x increases, y increases proportionally.

On the other hand, if x decreases, then y decreases proportionally.

Hence, we are to determine the constant of variation for the given relation: If y varies directly as x, and y is 12 when x is 1.2,

We are given that y varies directly as x, which means we can write this as:y=kx, where k is the constant of variation.

We are also given that y is 12 when x is 1.2.

Thus:12=k(1.2)

Dividing both sides by 1.2, we get:k=10

Hence, the constant of variation for this relation is k=10.

The correct answer is Option B. 10

For more questions on constant of variation

https://brainly.com/question/25215474

#SPJ8

Answer:

B

Step-by-step explanation:

The critical point of f(x, y) = x² - xy + 2y² - 5x + 6y - 9 is a local minimum.

To express "+ in terms of x and y" for the given expression u = J(u ди + ax ду x-y), we need to solve for +. Let's break down the steps:

Start with the equation: u = J(u ди + ax ду x-y)

Square both sides of the equation to eliminate the square root: u² = (u ди + ax ду x-y)²

Expand the squared expression on the right side: u² = (u ди)² + 2(u ди)(ax ду x-y) + (ax ду x-y)²

Simplify the terms: u² = u² + 2(u ди)(ax ду x-y) + (ax ду x-y)²

Subtract u² from both sides of the equation: 0 = 2(u ди)(ax ду x-y) + (ax ду x-y)²

Factor out (ax ду x-y): 0 = (ax ду x-y)[2(u ди) + (ax ду x-y)]

Solve for +: (ax ду x-y) = 0 or

2(u ди) + (ax ду x-y) = 0

So, the expression "+ in terms of x and y" is given by:

(ax ду x-y) = 0 or

(ax ду x-y) = -2(u ди)

Question 1 (b):

In the formula D = h is given as 0.1 + 0.002 and v as 0.3 ± 0.02, we need to express the approximate maximum error of D in terms of E.

The formula for D is: D = h

The given values are: h = 0.1 + 0.002 and

v = 0.3 ± 0.02

To find the approximate maximum error of D, we can use the formula:

Approximate maximum error of D = (absolute value of the coefficient of E) * (maximum value of E)

From the given values, we can see that E corresponds to the error in v. Therefore, the approximate maximum error of D in terms of E can be expressed as:

Approximate maximum error of D = (absolute value of 1) * (maximum value of E)

Approximate maximum error of D = 1 * 0.02

Approximate maximum error of D = 0.02

So, the approximate maximum error of D in terms of E is 0.02.

Question 1 (c):

To find and classify the critical point of f(x, y) = x² - xy + 2y² - 5x + 6y - 9, we need to find the partial derivatives and solve the system of equations.

Given function: f(x, y) = x² - xy + 2y² - 5x + 6y - 9

Partial derivative with respect to x (df/dx):

df/dx = 2x - y - 5

Partial derivative with respect to y (df/dy):

df/dy = -x + 4y + 6

To find the critical point, we need to solve the system of equations:

2x - y - 5 = 0

-x + 4y + 6 = 0

Solving these equations simultaneously, we get:

2x - y = 5 ...(Equation 1)

-x + 4y = -6 ...(Equation 2)

Multiplying Equation 1 by 4 and adding it to Equation 2:

8x - 4y - x + 4y = 20 - 6

7x = 14

x = 2

Substituting the value of x into Equation 1:

2(2) - y = 5

4 - y = 5

y = -1

Therefore, the critical point is (x, y) = (2, -1).

To classify the critical point, we need to evaluate the second partial derivatives:

Partial derivative with respect to x twice (d²f/dx²):

d²f/dx² = 2

Partial derivative with respect to y twice (d²f/dy²):

d²f/dy² = 4

Partial derivative with respect to x and then y (d²f/dxdy):

d²f/dxdy = -1

Partial derivative with respect to y and then x (d²f/dydx):

d²f/dydx = -1

To classify the critical point, we can use the discriminant:

Discriminant (D) = (d²f/dx²)(d²f/dy²) - (d²f/dxdy)(d²f/dydx)

D = (2)(4) - (-1)(-1)

D = 8 - 1

D = 7

Since the discriminant (D) is positive, and both d²f/dx² and d²f/dy² are positive, we can classify the critical point (2, -1) as a local minimum.

Therefore, the critical point of f(x, y) = x² - xy + 2y² - 5x + 6y - 9 is a local minimum.

To know more about minimum visit

https://brainly.com/question/21426575

#SPJ11

The surface area of the prism is 776 ft²

A prism is a solid shape that is bound on all its sides by plane faces.

The surface area of a prism is expressed as;

SA = 2B + pH

where p is the perimeter of the base , B is the base area and h is the height of the prism.

Base area = 1/2( a+b) h

= 1/2 × ( 20+8) 12

= 28 × 6

= 168 ft²

Perimeter of the base = 20+8 +15 + 12

= 55 ft

height = 8 ft

Therefore;

SA = 2 × 168 + 55× 8

SA = 336 + 440

SA = 776 ft²

The surface area of the prism is 776 ft²

learn more about surface area of prism from

https://brainly.com/question/1297098

#SPJ1

Answer:= x - 6 + 4 , - x - 6 + 4 is the inverse of f(x)=(x−4)2+

Step-by-step explanation:

Step-by-step explanation:

[tex]y = (x - 4) {}^{2} + 6[/tex]

[tex]y - 6 = (x - 4) {}^{2} [/tex]

[tex] \sqrt{y - 6} = (x - 4)[/tex]

[tex] \sqrt{y -6} + 4 = x[/tex]

Swap x and y.

[tex] \sqrt{x - 6} + 4 = y[/tex]

Let

[tex]y = f {}^{ - 1} (x)[/tex]

[tex]f {}^{ - 1} (x) = \sqrt{x - 6} + 4[/tex]

Using a numerical method such as the Newton-Raphson method, the first root of J₁(x)/x is found to be approximately 3.83.

Therefore, α = 3.83/3.

For a sphere of radius r, volume V, and surface area A (which is given by 4πr²), the Biot number can be defined as:

Bi=khV/A

where k is the thermal conductivity of the sphere material, h is the heat transfer coefficient and rho is the density of the material and cp is the specific heat of the material.

(a) For Copper, k = 212 BTU/(h-ft-F), rho = 555 lb/ft³, cp = 0.092 BTU/(lb-F)

The Biot number for copper can be calculated as:Bi = 3k/hR= (3 × 212)/(10 × 3 × 1) = 6.36

Therefore, a lumped analysis applies since Bi < 0.1.

Since a lumped analysis applies, the temperature of the sphere can be determined using the following equation:

T(t) - Ta = (Ti - Ta) × exp(-hAt/mc p

)where T(t) is the temperature of the sphere at time t, Ta is the ambient temperature of the surroundings (1000°F), Ti is the initial temperature of the sphere (70°F), m is the mass of the sphere, and t is the time.

The mass of the sphere can be calculated as:

m = rhoV= 555 × (4/3) × π × (3³) = 113097.24 lb

The specific heat capacity of copper is cp = 0.092 BTU/(lb-F).

Therefore, the product mc p is given by:

mc p = 113097.24 × 0.092 = 10403.0768

The temperature at the center of the sphere reaches 907°F after 53.06 seconds, which is calculated using:

T(t) = Ta + (Ti - Ta) × exp(-hAt/mc p)

= 1000 + (70 - 1000) × exp(-10 × 4π × (3)² × t/10403.0768)  

= 907

(b) For Asbestos, k = 0.08 BTU/(h-ft-F), rho = 36 lb/ft³, cp = 0.25 BTU/(lb-F)

The Biot number for asbestos can be calculated as:

Bi = 3k/hR= (3 × 0.08)/(10 × 3 × 1) = 0.072

Therefore, a distributed analysis applies since Bi > 0.1.

Thus, the temperature distribution within the sphere needs to be considered.

The temperature distribution is given by:

T(r,t) - Ta = (Ti - Ta) [I₀(αr) exp(-α²ht/ρcp)] / [I₀(αR)]

where I₀ is the modified Bessel function of the first kind of order zero, α is the first root of I₁(x)/x and R is the radius of the sphere.

The temperature at the center of the sphere can be determined by setting r = 0:

T(0,t) - Ta = (Ti - Ta) [I₀(0) exp(-α²ht/ρcp)] / [I₀(αR)]T(0,t) - Ta

= (Ti - Ta) exp(-α²ht/ρcp)T(0,t)

= Ta + (Ti - Ta) exp(-α²ht/ρcp)

The mass of the sphere can be calculated as:

m = rhoV= 36 × (4/3) × π × (3³) = 7322.4 lb

The specific heat capacity of asbestos is cp = 0.25 BTU/(lb-F).

Therefore, the product mc p is given by:

mc p = 7322.4 × 0.25 = 1830.6The temperature at the center of the sphere reaches 907°F after 72.6 seconds, which is calculated using:

T(0,t) = Ta + (Ti - Ta) exp(-α²ht/ρcp)

= 1000 + (70 - 1000) exp(-α² × 10 × 72.6/1830.6)

= 907

The value of α can be determined by solving the following equation:

J₁(x) = 0where J₁ is the Bessel function of the first kind of order one.

Using a numerical method such as the Newton-Raphson method, the first root of J₁(x)/x is found to be approximately 3.83.

Therefore, α = 3.83/3.

Know more about surface area here:

https://brainly.com/question/16519513

#SPJ11

None of the sides are congruent, as they have different side lengths.

When we have two points of the coordinate plane, the ordered pairs have coordinates [tex](x_1,y_1)[/tex] and [tex](x_2,y_2)[/tex].

The distance between them is given by the equation presented as follows, derived from the Pythagorean Theorem, as the distance is the hypotenuse:

[tex]D = \sqrt{(x_2-x_1)^2+(y_2-y_1)^2}[/tex]

The vertices of the quadrilateral in this problem are given as follows:

D(-2,-1), E(3, 13), F(15, 5), G(13, -11).

Hence the side lengths are given as follows:

Hence none of the sides are congruent, as they have different side lengths.

More can be learned about the distance between two points at https://brainly.com/question/7243416

#SPJ1

The exact value of cscA in simplest radical form using a rational denominator is -13/5.

To find the exact value of cscA in simplest radical form using a rational denominator, given tanA=-(12)/(5) and that angle A is in Quadrant IV, use the following steps:

Since A is in quadrant IV and tanA=-(12)/(5), let's draw a right triangle with its base being 12 and its height being -5. The opposite side of the triangle is negative because A is in Quadrant IV, which means sine is negative in this quadrant.

Find the hypotenuse using the Pythagorean Theorem:

c² = a² + b²c² = 12² + (-5)²c² = 144 + 25c² = 169c = √169c = 13

The values of the sides of the right triangle are now known:

a = 12b = -5c = 13

Using the definition of csc, cscA = 1/sinA, we can find the value of sinA: sinA = -5/13

Therefore, cscA = 1/(-5/13)cscA = -13/5

Therefore, the exact value of cscA in simplest radical form using a rational denominator is -13/5.

For more such questions on simplest radical form, click on:

https://brainly.com/question/565192

#SPJ8

The pH at the equivalence point is 12.

At the equivalence point, moles of acid = moles of base.

Therefore, moles of NaOH

= 0.1 L × 0.01 M = 0.001 moles

Moles of HOAc = 0.001

moles[HOAc] = moles of HOAc / volume of HOAc in litres[HOAc]

= 0.001 moles / 0.100 L = 0.01 M

Initially, [HOAc] = 0.01 M

Therefore, [OH⁻] = [H⁺]Kw = [H⁺] × [OH⁻][H⁺] = [OH⁻]

At equivalence point, [OH⁻] = 0.01 M

Applying the equation pOH + pH = 14pOH

= - log [OH⁻]pOH

= - log 0.01pOH

= 2pH = 14 - pOH

= 14 - 2pH

= 12

The pH at the equivalence point is 12.

: The pH at the equivalence point is 12.

To know more about moles visit:

brainly.com/question/15209553

#SPJ11