The stress-strain curve of structural steel with a yield point can generally be divided into three stages: elastic deformation, yielding, and plastic deformation.
In the first stage, known as elastic deformation, the steel material exhibits a linear relationship between stress and strain. This means that when stress is applied, the steel deforms elastically and returns to its original shape once the stress is removed. The steel behaves like a spring during this stage, with the deformation being directly proportional to the applied stress.
The second stage is the yielding stage. At this point, the stress-strain curve deviates from linearity, and plastic deformation begins to occur. The steel reaches its yield point, which is the stress level at which a significant amount of plastic deformation starts to take place. The material undergoes permanent deformation during this stage, even when the stress is reduced or removed.
The third stage is the plastic deformation stage. In this stage, the steel continues to deform plastically under increasing stress. The stress-strain curve shows a gradual increase in strain with increasing stress. The material may exhibit strain hardening, where its resistance to deformation increases as it continues to stretch. Ultimately, the steel may reach its ultimate strength, after which it may experience necking and eventual failure.
Overall, the stress-strain curve of structural steel with a yield point is characterized by the initial linear elastic deformation, followed by yielding and plastic deformation. These stages represent the steel's ability to withstand and accommodate varying levels of stress before reaching its breaking point.
To learn more about stress-strain curve refer:
https://brainly.com/question/13110518
#SPJ11
You are given three dairy products to incorporate into a dairy plant. You need to understand how each fluid will flow, so you measure their rheological properties, I determine the relationship between shear stress and shear rate for each fluid. Based on the relationships shown below, identify each fluid as a Newtonian fluid, Bingham plastic, or Power-Law fluid. If you identify any as Power-Law fluids, also identify whether they are shear-thinning or shear-thickening fluids. Type of fluid a. t = 1.13 dy0.26 b. t = 4.97 + 0.15 du dy C. T = 1000 du dy
To identify each fluid as a Newtonian fluid, Bingham plastic, or Power-Law fluid, we need to analyze the relationships between shear stress (τ) and shear rate (du/dy) for each fluid.
a. For the first fluid, the relationship is given as t = 1.13 dy^0.26.
Since the exponent (0.26) is less than 1, this indicates that the fluid follows a Power-Law behavior. To determine if it is shear-thinning or shear-thickening, we can look at the value of the exponent.
If the exponent is less than 1, it indicates shear-thinning behavior. In this case, the exponent is 0.26, which is less than 1. Therefore, the first fluid is a Power-Law fluid and it is shear-thinning.
b. For the second fluid, the relationship is given as t = 4.97 + 0.15 du/dy.
This relationship is not in the form of a Power-Law or Bingham plastic. It is a linear equation with a constant term (4.97) and a coefficient (0.15) multiplying the shear rate (du/dy). Therefore, the second fluid is a Newtonian fluid.
c. For the third fluid, the relationship is given as T = 1000 du/dy.
This relationship is also not in the form of a Power-Law or Bingham plastic. It is a linear equation with a coefficient of 1000 multiplying the shear rate (du/dy). Therefore, the third fluid is also a Newtonian fluid.
To summarize:
- The first fluid is a Power-Law fluid and it is shear-thinning.
- The second and third fluids are Newtonian fluids.
To know more about Newtonian fluid :
https://brainly.com/question/13348313
#SPJ11
Mrs. Jones buys two toys for her son. The probability that the first toy is defective is 1/3
, and the probability that the second toy is defective given that the first toy is defective is 1/5
. What is the probability that both toys are defective?
Answer:
[tex]\frac{1}{15\\}[/tex]
Step-by-step explanation:
The probability that the first toy is defective is [tex]\frac{1}{3}[/tex].
The probability that the second toy is defective given that the first toy is defective is [tex]\frac{1}{5}[/tex].
To find the probability that both toys are defective, we multiply the probability of the first toy being defective by the probability of the second toy being defective given that the first toy is defective.
Therefore, the probability that both toys are defective is [tex]\frac{1}{3}[/tex] x [tex]\frac{1}{5}[/tex] = [tex]\frac{1}{15\\}[/tex].
So the answer is [tex]\frac{1}{15\\}[/tex].
Which statement is always CORRECT?
A. If A is an 100×100 and AX=0 has a nonzero solution, then the rank of A is 100 . B. If b=[1,2,3,4]^T, then for any 4×2 matrix A the system AX=b has no solution. C. Each 3×3 nonzero shew-symmetric matrix is nonsingular. D. If for a square matrix A, a homogeneous system AX=0 has only one solution X=0, then A is nonsingular.
The correct statement is D. If for a square matrix A, a homogeneous system AX=0 has only one solution X=0, then A is nonsingular.
To understand why this statement is always correct, let's break it down step-by-step:
1. We have a square matrix A, which means the number of rows is equal to the number of columns.
2. The homogeneous system AX=0 represents a system of linear equations, where A is the coefficient matrix and X is the variable matrix.
3. When we say that AX=0 has only one solution X=0, it means that the only way to satisfy the system of equations is by setting all variables to zero.
4. This implies that the columns of A are linearly independent. In other words, no column can be expressed as a linear combination of the other columns.
5. When the columns of a matrix are linearly independent, it means that the matrix has full rank. The rank of a matrix is the maximum number of linearly independent columns or rows it contains.
6. A square matrix A is nonsingular if and only if its rank is equal to the number of columns (or rows). So, if the rank of A is equal to the number of columns, then A is nonsingular.
Therefore, if for a square matrix A, a homogeneous system AX=0 has only one solution X=0, then A is nonsingular.
Learn more about a Square matrix: https://brainly.com/question/31484624
#SPJ11
Cross section below is under a Moment as shown in the a. Normal stress at B b. Normal stress at D B = 15° A B M=16 kN.m C D T 60 mm 20 mm ↓ 15 mm
The normal stress at points B and D in the given cross-section under the applied moment are 0.0015N/m[tex]m^{2}[/tex] and 2N/m[tex]m^{2}[/tex]
Given:
Applied moment (M) = 16 kN.m
Distance from the centroid to point B (B) = 15 mm
Distance from the centroid to point D (D) = 20 mm
Thickness of the cross-section (T) = 60 mm
Height of the cross-section (C) = 20 mm
↓ indicates the direction of the applied moment
a. Normal stress at point B:
To calculate the normal stress at point B, we need to consider the bending stress due to the applied moment.
The bending stress (σ) can be calculated using the formula:
σ = (M * y) / I
where M is the applied moment, y is the distance from the centroid to the point where we want to calculate the stress, and I is the moment of inertia of the cross-section.
The moment of inertia (I) for a rectangular cross-section is given by:
I = (T * C^3) / 12
Substituting the given values:
I = (60 mm * (20 mm)^3) / 12
I = 160,000 mm^4
Now, let's calculate the normal stress at point B:
σ_B = (16 kN.m * 15 mm) / 160,000 mm^4= 0.0015
Note: It's important to convert the moment from kN.m to N.mm to ensure consistent units.
b. Normal stress at point D:
To calculate the normal stress at point D, we follow the same procedure as for point B:
σ_D = (M * y) / I
= (16 kN.m * 20 mm) / 160,000 mm^4= 2N/mm^2
The normal stress at point D is 2 N/mm².
Now, you can calculate the values for σ_B and σ_D using the given formulas and the provided values.
Learn more about Axis:
https://brainly.com/question/31350785
#SPJ11
If P is the midpoint of QR find the length of QR
A.
37
B. 38
C. 40
D. 43
Please select the best answer from the choices provided
OA
OB
О с
D
Given that P is the midpoint of QR, the length of QR is twice the length of PQ (or PR). Among the options provided, the correct answer is D, which is 43.
Let's assume that P is the midpoint of QR. In a line segment with a midpoint, the distance from one endpoint to the midpoint is equal to the distance from the midpoint to the other endpoint.
So, if P is the midpoint of QR, we can say that PQ is equal to PR. Therefore, the length of QR would be twice the length of PQ (or PR).
Given the answer choices, we need to find the length of QR among the options provided (A, B, C, D). We can eliminate options A and C because they are not even numbers, and it's unlikely for a midpoint to result in a decimal value.
Now, let's check options B and D. If we divide them by 2, we get 19 and 21.5, respectively. Since we're dealing with a line segment, it is more reasonable for the length to be a whole number. Therefore, we can conclude that the correct answer is option D, which is 43.
Hence, the length of QR is 43.
For more questions on the midpoint, click on:
https://brainly.com/question/896396
#SPJ8
Solve the initial value problem
dy/dt-y = 8e^t + 12e^5t, y(0) = 10 y(t) Water leaks from a vertical cylindrical tank through a small hole in its base at a rate proportional to the square root of the volume of water remaining. The tank initially contains 100 liters and 23 liters leak out during the first day. A. When will the tank be half empty? t = days B. How much water will remain in the tank after 5 days? volume = Liters
(t_{\text{half-empty}} = \frac{{50 - 2\sqrt{77}}}{{20 - 2\sqrt{77}}}) (days)
B. The remaining volume after 5 days:
(V(5) = \frac{{(4(20 - 2\sqrt{77}) + 2\sqrt{77})^2}}{4}) (liters)
To solve the initial value problem, we have the differential equation dy/dt - y = 8e^t + 12e^5t with the initial condition y(0) = 10.[\frac{{dy}}{{dt}} - y = 8e^t + 12e^{5t}, \quad y(0) = 10]
To solve this, we use the method of integrating factors.
First, we rewrite the equation in the standard form:
[\frac{{dy}}{{dt}} - y = 8e^t + 12e^{5t}]
Next, we identify the integrating factor, which is the exponential of the integral of the coefficient of y.
In this case, the coefficient of y is −1, so the integrating factor is (e^{-t}).
Now, we multiply the entire equation by the integrating factor:
[e^{-t} \cdot \frac{{dy}}{{dt}} - e^{-t} \cdot y = 8e^t \cdot e^{-t} + 12e^{5t} \cdot e^{-t}]
Simplifying this equation gives:
[\frac{{d}}{{dt}} (e^{-t} \cdot y) = 8 + 12e^{4t}]
Integrating both sides with respect to t gives:
[\int \frac{{d}}{{dt}} (e^{-t} \cdot y) , dt = \int (8 + 12e^{4t}) , dt]
Integrating the left side gives:
[e^{-t} \cdot y = 8t + 3e^{4t} + C]
To find the constant of integration C, we use the initial condition y(0)=10:
[e^{-0} \cdot 10 = 8(0) + 3e^{4(0)} + C]
Solving this equation gives:
[10 = 3 + C]
So, C=7.
Substituting the value of C back into the equation gives:
[e^{-t} \cdot y = 8t + 3e^{4t} + 7]
Finally, solving for y gives:
[y = (8t + 3e^{4t} + 7) \cdot e^t]
Therefore, the solution to the initial value problem is:
[y = (8t + 3e^{4t} + 7) \cdot e^t]
To solve this problem, let's denote the volume of water in the tank at any time (t) as (V(t)) (in liters). We know that the rate of leakage is proportional to the square root of the remaining volume. Mathematically, we can express this relationship as:(\frac{{dV}}{{dt}} = k \sqrt{V})
where (k) is the proportionality constant.
Given that 23 liters leak out during the first day, we can write the initial condition as:
(V(1) = 100 - 23 = 77) liters
To find the value of (k), we can substitute the initial condition into the differential equation:
(\frac{{dV}}{{dt}} = k \sqrt{V})
(\frac{{dV}}{{\sqrt{V}}} = k dt)
Integrating both sides:
(2\sqrt{V} = kt + C)
where (C) is the constant of integration.
Using the initial condition (V(1) = 77), we can find the value of (C) as follows:
(2\sqrt{77} = k(1) + C)
(C = 2\sqrt{77} - k)
Substituting back into the equation:
(2\sqrt{V} = kt + 2\sqrt{77} - k)
Now, let's answer the specific questions:
A. When will the tank be half empty? We want to find the time (t) when the volume (V(t)) is equal to half the initial volume.
(\frac{1}{2} \cdot 100 = 2\sqrt{77} + k \cdot t_{\text{half-empty}})
Simplifying:
(50 - 2\sqrt{77} = k \cdot t_{\text{half-empty}})
Solving for (t_{\text{half-empty}}):
(t_{\text{half-empty}} = \frac{{50 - 2\sqrt{77}}}{{k}})
When will the tank be half empty?
(t_{\text{half-empty}} = \frac{{50 - 2\sqrt{77}}}{{20 - 2\sqrt{77}}}) (days)
B. The remaining volume in the tank after 5 days can be found by substituting (t = 5) into the equation we derived:
(2\sqrt{V} = k \cdot 5 + 2\sqrt{77} - k)
Simplifying:
(2\sqrt{V} = 5k + 2\sqrt{77} - k)
(2\sqrt{V} = 4k + 2\sqrt{77})
Squaring both sides:
(4V = (4k + 2\sqrt{77})^2)
Simplifying:
(V = \frac{{(4k + 2\sqrt{77})^2}}{4})
The value of (k) can be determined from the initial condition:
(2\sqrt{100} = k \cdot 1 + 2\sqrt{77})
(20 = k + 2\sqrt{77})
(k = 20 - 2\sqrt{77})
The remaining volume after 5 days:
(V(5) = \frac{{(4(20 - 2\sqrt{77}) + 2\sqrt{77})^2}}{4}) (liters)
Learn more about initial value problem:
https://brainly.com/question/30883066
#SPJ11
U Question 2 The ballerina rose to prominence in the nineteenth-century European professional dance scene. a) True b) False
The statement is true. The ballerina did indeed rise to prominence in the nineteenth-century European professional dance scene, leaving a lasting impact on the art of ballet.
The statement "The ballerina rose to prominence in the nineteenth-century European professional dance scene" is true. The nineteenth century was a significant period for the development and establishment of ballet as a recognized art form in Europe. During this time, ballet underwent significant changes and transformations, and the role of the ballerina became increasingly prominent.
In the nineteenth century, ballet companies and schools were established across Europe, particularly in France, Russia, and Italy, which became the centers of ballet excellence. The Romantic era in the early to mid-nineteenth century brought about a shift in ballet aesthetics, with a focus on ethereal, otherworldly themes and delicate, graceful movements. This era saw the emergence of iconic ballerinas such as Marie Taglioni and Fanny Elssler, who captured the imagination of audiences with their technical skill and artistic expression.
Ballerinas became revered figures in the ballet world, commanding the stage with their virtuosity and captivating performances. Their achievements and contributions to the art form elevated the status of ballet as a serious and respected profession. The success and influence of ballerinas during this period laid the foundation for the continued prominence of the ballerina in the professional dance scene throughout the twentieth and twenty-first centuries.
In conclusion, the statement is true. The ballerina did indeed rise to prominence in the nineteenth-century European professional dance scene, leaving a lasting impact on the art of ballet.
Learn more about ballerina
https://brainly.com/question/31683545
#SPJ11
Consumers in a certain area can choose between three package delivery services: APS, GX, and WWP. Each week, APS loses 10% of its customers to GX and 20% to WWP, GX loses 15% of its customers to APS and 10% to WWP, and WWP loses 5% of its customers to APS and 5% to GX. Assuming that these percentages remain valid over a long period of time, what is each com- pany's expected market share in the long run?
Using the given information, in the long run, APS is expected to have a market share of approximately 35.6%, GX is expected to have a market share of approximately 39.0%, and WWP is expected to have a market share of approximately 25.4%.
Determining the market share of each companyLet represent each package delivery service with their first letter which is A, G, and W for APS, GX, and WWP, respectively. Then, set up a system of linear equations based on the information given
A(n+1) = 0.7A(n) + 0.05G(n) + 0.05W(n)
G(n+1) = 0.15A(n) + 0.9G(n) + 0.1W(n)
W(n+1) = 0.05A(n) + 0.05G(n) + 0.95W(n)
where n is the week number (starting from 0).
The coefficients of the equations represent the percentage of customers retained by each company and the percentage gained from each of the other companies in a given week.
To find the long-term market shares
Setting A(n+1) = A(n) = A, G(n+1) = G(n) = G, and W(n+1) = W(n) = W
A = 0.7A + 0.05G + 0.05W
G = 0.15A + 0.9G + 0.1W
W = 0.05A + 0.05G + 0.95W
Solve for the equations to get;
A = 21/59 ≈ 0.356
G = 23/59 ≈ 0.390
W = 15/59 ≈ 0.254
Thus, in the long run, APS, GX and WWP are expected to have a market share of approximately 35.6%, 39.0%, and 25.4%, respectively.
Learn more on market share on https://brainly.com/question/4017104
#SPJ4
Which type of the following hydraulic motor that has limited rotation angle: А Gear motor B Rotary actuator Piston motor D) Vane motor
The type of hydraulic motor that has a limited rotation angle is the Rotary actuator.
A rotary actuator is a type of hydraulic motor that is designed to convert hydraulic pressure into rotational motion. Unlike other hydraulic motors such as gear motors, piston motors, and vane motors, a rotary actuator is specifically designed to provide limited rotation.
Rotary actuators are commonly used in applications where precise control of rotation is required, such as in robotics, automation systems, and machinery. They can be used to control valves, gates, or other mechanisms that require limited rotation angles.
In contrast, gear motors, piston motors, and vane motors can provide continuous rotation without any limitation on the angle. Gear motors use gears to transmit power and provide rotational motion. Piston motors use pistons to convert hydraulic pressure into rotational motion. Vane motors use vanes that slide in and out of a rotor to generate rotation.
To know more about Rotary actuator :
https://brainly.com/question/33586156
#SPJ11
Let the "Tribonacci sequence" be defined by T_1=T_2=T-3=1 and T_n=T_n−1+T_n−2+T_n−3 for n≥4. Prove that Tn<2^n for all n∈N
The Tribonacci sequence is defined as follows:
T_1 = T_2 = T_3 = 1
T_n = T_{n-1} + T_{n-2} + T_{n-3} for n ≥ 4.
To prove that T_n < 2^n for all n ∈ N, we will use mathematical induction.
Step 1: Base case
Let's first verify the inequality for the base cases n = 1, 2, and 3:
T_1 = T_2 = T_3 = 1, and 2^1 = 2, which satisfies T_n < 2^n.
Step 2: Inductive hypothesis
Assume that the inequality holds true for some arbitrary positive integer k, i.e., T_k < 2^k.
Step 3: Inductive step
We need to prove that the inequality holds for k+1, i.e., T_{k+1} < 2^{k+1}.
Using the definition of the Tribonacci sequence, we have:
T_{k+1} = T_k + T_{k-1} + T_{k-2}
Now, let's express each term in terms of T_n:
T_k = T_{k-1} + T_{k-2} + T_{k-3}
T_{k-1} = T_{k-2} + T_{k-3} + T_{k-4}
T_{k-2} = T_{k-3} + T_{k-4} + T_{k-5}
Substituting these expressions into T_{k+1}, we get:
T_{k+1} = (T_{k-1} + T_{k-2} + T_{k-3}) + (T_{k-2} + T_{k-3} + T_{k-4}) + (T_{k-3} + T_{k-4} + T_{k-5})
= 2(T_{k-1} + T_{k-2} + T_{k-3}) + (T_{k-4} + T_{k-5})
Now, using the inductive hypothesis, we can replace T_k, T_{k-1}, and T_{k-2} with 2^{k-1}, 2^{k-2}, and 2^{k-3} respectively:
T_{k+1} < 2(2^{k-1} + 2^{k-2} + 2^{k-3}) + (T_{k-4} + T_{k-5})
= 2^k + 2^{k-1} + 2^{k-2} + T_{k-4} + T_{k-5}
< 2^k + 2^k + 2^k + 2^k + 2^k (by the inductive hypothesis)
= 5(2^k)
Since 5 < 2^k for all positive integers k, we have:
T_{k+1} < 5(2^k)
Step 4: Conclusion
We have shown that if the inequality holds for k, then it also holds for k+1. Since it holds for the base cases (n = 1, 2, 3), it holds for all positive integers n by the principle of mathematical induction.
Therefore, we can conclude that T_n < 2^n for all n ∈ N.
Learn more about Tribonacci sequence on the given link:
https://brainly.com/question/32200098
#SPJ11
Given the functions f(x)=sinx and g(x)=3, determine the range of the combined function y=f(x)+g(x). a) {y∈R,−3≤y≤3} b) {y∈R,2≤y≤4} c) {y∈R} d) {y∈R,−1≤y≤1}
The functions f(x) = sin x and g(x) = 3 are given. We need to find the range of the combined function y = f(x) + g(x).The range of the combined function can be determined using the following formula: Range(y) = Range(f(x)) + Range(g(x))
Now, the range of f(x) is [-1,1]. This is because the maximum value of sin x is 1 and the minimum value is -1. The range of g(x) is simply {3}.Using the formula,
Range(y) = Range(f(x)) + Range(g(x))= [-1,1] + {3}= {y ∈ R, -1 ≤ y ≤ 4}
Therefore, the correct option is d) {y ∈ R, -1 ≤ y ≤ 1}. We are given the functions f(x) = sin x and g(x) = 3. We need to find the range of the combined function y = f(x) + g(x).To find the range of the combined function, we first need to find the ranges of the individual functions f(x) and g(x).The range of f(x) is [-1,1]. This is because the maximum value of sin x is 1 and the minimum value is -1. Therefore, the range of f(x) is [-1,1].The range of g(x) is simply {3}. This is because g(x) is a constant function and it takes the value 3 for all values of x. Now, we can use the formula:
Range(y) = Range(f(x)) + Range(g(x))
to find the range of the combined function. Range(y) = [-1,1] + {3}= {y ∈ R, -1 ≤ y ≤ 4}Therefore, the range of the combined function y = f(x) + g(x) is {y ∈ R, -1 ≤ y ≤ 4}.
The range of the combined function y = f(x) + g(x) is {y ∈ R, -1 ≤ y ≤ 4}.
To learn more about range visit:
brainly.com/question/28135761
#SPJ11
what is applications of
1- combination pH sensor
2- laboratory pH sensor
3- process pH sensor
4- differential pH sensor
1. Combination pH sensor: A combination pH sensor is an electrode that measures the acidity or alkalinity of a solution using a glass electrode and a reference electrode, both of which are immersed in the solution.
The most frequent application of the combination pH sensor is in chemical analysis and laboratory settings, where it is employed to monitor the acidity or alkalinity of chemical solutions, soil, and water.
2. Laboratory pH sensor: In laboratory settings, pH sensors are utilized to determine the acidity or alkalinity of chemical solutions and other compounds. The sensor may be a handheld or bench-top device that is frequently used in laboratories to evaluate chemicals and compounds.
3. Process pH sensor: In process control industries, such as pharmaceuticals, petrochemicals, and other manufacturing facilities, process pH sensors are employed to control chemical reactions and ensure that they occur at the correct acidity or alkalinity. These sensors are integrated into pipelines or tanks to constantly monitor the acidity or alkalinity of the substance being manufactured.
4. Differential pH sensor: Differential pH sensors are used to measure the difference in pH between two different solutions or environments. They are frequently utilized to determine the acidity or alkalinity of two distinct solutions and to monitor chemical reactions in the two solutions.
Combination, laboratory, process, and differential pH sensors all have numerous applications in the fields of chemical analysis, industrial production, and laboratory settings. Combination pH sensors are used most often in laboratory and chemical analysis settings to monitor the acidity or alkalinity of chemical solutions, soil, and water. In laboratory settings, pH sensors are used to determine the acidity or alkalinity of chemical solutions and other compounds.
Process pH sensors are employed to control chemical reactions and ensure that they occur at the correct acidity or alkalinity in process control industries, such as pharmaceuticals, petrochemicals, and other manufacturing facilities.
Differential pH sensors are utilized to determine the acidity or alkalinity of two distinct solutions and to monitor chemical reactions in the two solutions.
Differential pH sensors may also be utilized in environmental applications to monitor the acidity or alkalinity of soil or water. Combination, laboratory, process, and differential pH sensors all have numerous applications in industrial and laboratory settings, and their use is critical to ensuring that chemical reactions occur correctly and that the appropriate acidity or alkalinity levels are maintained.
The combination, laboratory, process, and differential pH sensors all have numerous applications in chemical analysis, industrial production, and laboratory settings. In laboratory settings, pH sensors are utilized to determine the acidity or alkalinity of chemical solutions and other compounds. Combination pH sensors are used most often in laboratory and chemical analysis settings to monitor the acidity or alkalinity of chemical solutions, soil, and water. Process pH sensors are employed to control chemical reactions and ensure that they occur at the correct acidity or alkalinity in process control industries. Differential pH sensors are utilized to determine the acidity or alkalinity of two distinct solutions and to monitor chemical reactions in the two solutions.
To know more about petrochemicals :
brainly.com/question/28540307
#SPJ11
Complete as a indirect proof
1. X ⊃Z
2. Y ⊃W
3. (Zv W)⊃~A
4. (A v B)⊃ (XvY) /~A
We have derived ~A from the assumption A, which leads to a contradiction. Therefore, the original statement ~A is proven indirectly.
To prove the statement ~A, we can assume A and derive a contradiction.
X ⊃ Z
Y ⊃ W
(Z v W) ⊃ ~A
(A v B) ⊃ (X v Y) (Premise)
Assume A:
5. A (Assumption)
A v B (Disjunction Introduction, from 5)
X v Y (Modus Ponens, from 4 and 6)
Now, we will derive a contradiction from the assumption A.
~Z (Modus Tollens, from 1 and 7)
~Z v ~W (Disjunction Introduction, from 8)
~A (Modus Ponens, from 3 and 9)
We have derived ~A from the assumption A, which leads to a contradiction. Therefore, the original statement ~A is proven indirectly.
To learn more about contradiction visit: https://brainly.com/question/1991016
#SPJ11
160.0 mL of 0.12M C_2H_5NH_2 with 285.0 mL of 0.21M C_2H_5NH_5Cl.. For HF,C_2H_5NH_2,K_b=4.5x10^-4.Express your answer using two decimal places.
The pH of the solution is 11.15.
Given parameters:
Volume of 0.12 M C2H5NH2: 160 mL
Volume of 0.21 M C2H5NH4Cl: 285 mL
Kb for C2H5NH2: 4.5 x [tex]10^{-4}[/tex]
Molar mass of C2H5NH2: 59.11 g/mol
Balanced equation:
C2H5NH2 (aq) + H2O (l) ↔ C2H5NH3+ (aq) + OH- (aq)
Equation for Kb:
Kb = [C2H5NH3+][OH-] / [C2H5NH2]
Assuming [C2H5NH3+] = [OH-] because it is a weak base:
[C2H5NH3+] = [OH-] = x
[C2H5NH2] = 0.12 M - x
Equilibrium expression:
Kb = (x)^2 / (0.12 - x)
Using the quadratic formula to solve for x:
x = [OH-] = 1.41 x [tex]10^{-3}[/tex] M
This concentration is also the concentration of [C2H5NH3+] produced.
Therefore, [C2H5NH2] remaining = 0.12 M - 1.41 x [tex]10^{-3}[/tex] M = 0.1186 M
Number of moles of C2H5NH2:
0.1186 M x (160/1000) L = 0.01898 mol
Number of moles of C2H5NH4Cl:
0.21 M x (285/1000) L = 0.05985 mol
Determining the limiting reactant:
0.01898 mol < 0.05985 mol
C2H5NH2 is the limiting reactant.
Number of moles of C2H5NH3+ produced = number of moles of C2H5NH2 consumed = 0.01898 mol
Concentration of the weak base after the reaction:
0.1186 M - 0.01898 M = 0.09962 M
Calculating pOH:
pOH = -log[OH-]
pOH = -log(1.41 x 10^-3)
pOH = 2.85
Calculating pH:
pH + pOH = 14
pH = 14 - pOH
pH = 11.15
Learn more about pH from the given link:
https://brainly.com/question/12609985
#SPJ11
Show the complete solution and the necessary graphs/diagrams.
Use 2 decimal places in the final answer.
A particle moves that is defined by the parametric equations
given below (where x and y are in m
Now we have a relationship between x and y. We can plot the graph by assigning different values to x and calculating corresponding y values. Using a graphing calculator or software, we can visualize the motion of the particle.
The given parametric equations define the motion of a particle in terms of its x and y coordinates. To find the complete solution and necessary graphs/diagrams, we need to eliminate the parameter and express the relationship between x and y.
Let's consider the given parametric equations:
x = 4t^2 - 6t
y = 3t^2 + 2t
To eliminate the parameter t, we can solve the first equation for t in terms of x and substitute it into the second equation:
4t^2 - 6t = x
t(4t - 6) = x
t = (x)/(4t - 6)
Substituting this value of t into the second equation, we have:
y = 3[(x)/(4t - 6)]^2 + 2[(x)/(4t - 6)]
Simplifying further, we get:
y = (3x^2)/(16t^2 - 48t + 36) + (2x)/(4t - 6)
Learn more about coordinates:
https://brainly.com/question/32836021
#SPJ11
what is the solution to the system of equations given below is x=2y+3 x-5y=-56
The solution to the system of equations x = 2y + 3 and x - 5y = -56 is (127/3, 59/3).
The system of equations can be solved by graphing, substitution method, or elimination method. we can choose the substitution method as it is more feasible for this question.
The first equation is:
x = 2y + 3 -------- (1)
The second equation is:
x - 5y = -56
Add 5y on both sides:
x = 5y - 56 ---------- (2)
Substitute (1) into (2):
2y + 3 = 5y - 56
Subtract 5y on both sides:
-3y + 3 = -56
Subtract 3 on both sides:
-3y = -59
Divide by -3 on both sides:
y = 59/3
x = 2y + 3
Substitute the value of y into (1) to find x:
x = 2(59/3) + 3
Calculate:
x = 127/3
Thus, the solution to the system of equations is ( 127/3, 59/3 ).
Learn more about substitution method:
brainly.com/question/25869125
Define (+√−3. Is ¢ a unit in Z[C]?
Definition of (+√−3): The square root of -3 is represented by √-3, which is an imaginary number. If we add √-3 to any real number, we obtain a complex number.
If a complex number is represented in the form a + b√-3, where a and b are real numbers, it is referred to as an element of Z[√-3]. Here, it is unclear what Z[C] represents. So, it is tough to provide a straight answer to this question. But, if we presume that Z[C] refers to the ring of complex numbers C, then:
When we multiply two complex numbers, the resulting complex number has a magnitude that is the product of the magnitudes of the factors. Also, when we divide two complex numbers, the magnitude of the result is the quotient of the magnitudes of the numbers that are being divided.
To know more about break visit;
https://brainly.com/question/30162440
#SPJ11
by the COVID 19 pandemic. Most construction companies had to reduce their operations until the necessary guidelines were determined to ensure the well-being of the workers thus affecting different aspects in the construction sites. Q3. Discuss four major COVID-related health and safety measures introduced in construction sites.
The COVID-19 pandemic has led to the implementation of various health and safety measures in construction sites. Social distancing, the use of personal protective equipment, enhanced hygiene practices, and regular sanitization and cleaning are among the major measures introduced.
These measures aim to protect the health and well-being of construction workers and minimize the spread of the virus within construction sites. By implementing these measures, construction companies can create a safer work environment and mitigate the impact of the pandemic on construction operations.
Four major COVID-related health and safety measures introduced in construction sites are:
1. Social distancing: Construction sites have implemented measures to maintain social distancing among workers. This includes reducing the number of workers on-site, staggering work schedules, and creating physical barriers or marked zones to ensure workers maintain a safe distance from each other.
2. Personal protective equipment (PPE): The use of personal protective equipment has been emphasized to minimize the spread of COVID-19. Construction workers are required to wear appropriate PPE, such as face masks, gloves, and safety goggles, depending on the tasks they perform.
3. Enhanced hygiene practices: Construction sites have implemented rigorous hygiene practices to prevent the spread of the virus. This includes providing handwashing stations or hand sanitizers at multiple locations on-site, promoting frequent handwashing, and encouraging respiratory etiquette, such as coughing or sneezing into elbows.
4. Regular sanitization and cleaning: Construction sites have increased the frequency of cleaning and disinfection activities. High-touch surfaces, shared tools, and equipment are regularly sanitized to minimize the potential transmission of the virus. Common areas, such as breakrooms and portable toilets, are also cleaned and disinfected regularly.
1. Social distancing: Social distancing measures have been introduced to minimize close contact and reduce the risk of virus transmission among construction workers. By reducing the number of workers on-site and implementing physical distancing protocols, the likelihood of COVID-19 spread can be minimized.
2. Personal protective equipment (PPE): PPE is essential to protect workers from exposure to the virus. Construction workers are required to wear appropriate PPE, such as masks, gloves, and goggles, depending on their tasks and the level of risk involved. PPE helps to prevent the inhalation or contact transmission of the virus.
3. Enhanced hygiene practices: Promoting good hygiene practices is crucial in preventing the spread of COVID-19 on construction sites. Handwashing stations or hand sanitizers are made readily available, and workers are encouraged to wash their hands frequently with soap and water for at least 20 seconds. Respiratory etiquette, such as covering coughs and sneezes, is also emphasized.
4. Regular sanitization and cleaning: Construction sites have increased the frequency of cleaning and disinfection activities. High-touch surfaces, shared tools, and equipment are regularly sanitized to reduce the risk of virus transmission. Common areas, such as breakrooms and portable toilets, are cleaned and disinfected regularly to maintain a hygienic environment.
Learn more about COVID-19 pandemic visit:
https://brainly.com/question/29643338
#SPJ11
i need help pleaseee!!
Step-by-step explanation:
A= πr^2
A = 8^2×π=64π= 201.06 ft^2
5.) What color are copper. (II) ions when in solution? 5.) a.) blue b.) yellow C.) red-brown d.) colorless
a). blue. is the correct option. When in a solution, copper (II) ions are blue in color. Copper (II) ions, also known as cupric ions, are a type of cation.
They are frequently encountered in chemical reactions and solutions and are derived from copper (II) compounds.
Copper (II) ions are frequently found in solution with water molecules, forming an aquo complex. Copper (II) sulfate, CuSO4, for example, has Cu2+ ions surrounded by four water molecules in its hydrated form. Copper (II) ions, like other transition metal cations, have several electron configurations, and their electron configuration can vary depending on their oxidation state.
The chemical symbol for the copper (II) ion is Cu2+.Cu2+ ions are light blue when in a solution. For example, copper sulfate solutions appear to be bright blue in color due to the presence of copper (II) ions. Copper (II) chloride, another copper (II) compound, produces a similar blue solution.
To know more about copper visit:
brainly.com/question/31035006
#SPJ11
Let u = (1,2,-1) and (0,2,-4) be vectors in R3.
Part(a) [3 points] If P(3, 4, 5) is the terminal point of the vector 3u, then what is its initial point? Show your work.
Part(b) [4 points] Find ||u||2v - (v. u)u.
Part (c) [4 points] Find vectors x and y in R³ such that u = x + y where x is parallel to v and y is orthogonal to V.
Hint: Consider orthogonal projection
a). The initial point of the vector 3u is (0, -2, 8).
b). ||u||²v - (v · u)u = (-10, -8, -14).
c). x = (0, 0.8, -1.6) and y = (1, 1.2, 0.6) are the vectors in R³ such that u = x + y, where x is parallel to v and y is orthogonal to v.
Part (a):
To find the initial point of the vector 3u, we need to subtract 3u from the terminal point P(3, 4, 5).
Initial point = P - 3u
Initial point = (3, 4, 5) - 3(1, 2, -1)
Initial point = (3, 4, 5) - (3, 6, -3)
Initial point = (3 - 3, 4 - 6, 5 - (-3))
Initial point = (0, -2, 8)
Therefore, the initial point of the vector 3u is (0, -2, 8).
Part (b):
To find ||u||²v - (v · u)u, we need to perform the following calculations:
||u||² = (1² + 2² + (-1)²) = 6
(v · u) = (0 * 1) + (2 * 2) + (-4 * (-1)) = 10
Substituting the values into the equation:
||u||²v - (v · u)u = 6v - 10u
Since v and u are given as (0, 2, -4) and (1, 2, -1) respectively, we can substitute these values:
6v - 10u = 6(0, 2, -4) - 10(1, 2, -1)
= (0, 12, -24) - (10, 20, -10)
= (0 - 10, 12 - 20, -24 + 10)
= (-10, -8, -14)
Therefore, ||u||²v - (v · u)u = (-10, -8, -14).
Part (c):
To find vectors x and y in R³ such that u = x + y, where x is parallel to v and y is orthogonal to v, we can use the concept of orthogonal projection.
We can express u as the sum of two vectors: x and y.
u = x + y
Where x is the projection of u onto v and y is the orthogonal component of u to v.
The projection of u onto v can be calculated as:
x = ((u · v) / ||v||²) * v
Substituting the given values:
x = ((1 * 0) + (2 * 2) + (-1 * (-4))) / ((0² + 2² + (-4)²)) * (0, 2, -4)
= (8 / 20) * (0, 2, -4)
= (0, 0.8, -1.6)
To find y, we subtract x from u:
y = u - x
= (1, 2, -1) - (0, 0.8, -1.6)
= (1 - 0, 2 - 0.8, -1 - (-1.6))
= (1, 1.2, 0.6)
Therefore, x = (0, 0.8, -1.6) and y = (1, 1.2, 0.6) are the vectors in R³ such that u = x + y, where x is parallel to v and y is orthogonal to v.
To know more about vector click-
https://brainly.com/question/31265178
#SPJ11
(3xy)²xty
дод
Зуз
0 3xy3
0
9xy3
о 9х5 3
Step-by-step explanation:
To simplify this expression, we need to apply the power rule of exponentiation, which states that (a^n)^m = a^(n*m).
In this case, we can start by squaring the expression within the parentheses:
(3xy)^2 = (3xy)*(3xy) = 9x^2y^2
Then, we can substitute this into the original expression:
(3xy)^2xty = 9x^2y^2xty = 9x^(2+1)y^(2+1)t = 9x^3y^3t
Therefore, the simplified form of the expression (3xy)^2xty is 9x^3y^3t.
Determine the solution of the given differential equation. y" + 8y' + 7y = 0 = Show all calculations in support of your answers.
The solution of the given differential equation is y = c1e^(-t) + c2e^(-7t).To determine the solution of the given differential equation, we can follow the steps below.
The auxiliary equation (characteristic equation) is given by r² + 8r + 7 = 0.Using the quadratic formula, we can find the roots as follows:
r = (-b ± √(b² - 4ac))/2a
where a = 1,
b = 8 and
c = 7.
r = (-8 ± √(8² - 4(1)(7)))/2(1)
r = (-8 ± √(64 - 28))/2
r = (-8 ± √36)/2
r = (-8 ± 6)/2
r1 = -1,
r2 = -7
The general solution is given by y = c1e^(-t) + c2e^(-7t)
where c1 and c2 are constants of integration. Show all calculations in support of your answers.Hence, the solution of the given differential equation is
y = c1e^(-t) + c2e^(-7t).
To know more about differential equation visit:
https://brainly.com/question/32645495
#SPJ11
Answer the following questions in regards to the following molecule: a) How many sigma bonding molecular orbitals are there in the MO of this molecule ? (total number of sigma bonding Mo) b) How many sigma bonding sp-sp molecular orbitals are there in the MO of this molecule ? c) How many artibonding MO are there in MO of this molecule ? (total number of antibonding Mo, sigma and pl) d) Nome the HOMO (Highest Occupied Molecular Ortital) of this molecule ?
1) There are six sigma bonding molecular orbitals
2) There is one sigma bonding sp-sp molecular orbital.
3) There are twelve antibonding molecular orbitals
4) The highest occupied molecular orbital is π*
What is a molecular orbital?A molecular orbital is an area of space where there is a high chance of encountering electrons. Atomic orbitals from the many constituent atoms of the molecule overlap to form it. In other words, rather than concentrating on specific atoms, molecular orbitals explain the distribution of electrons in a molecule as a whole.
When two atomic orbitals join, the same number of molecular orbitals is created. According to the Aufbau principle and Pauli exclusion principle, these molecular orbitals can be filled with electrons in a manner similar to how electrons fill atomic orbitals.
Learn more about molecular orbital:https://brainly.com/question/29642622
#SPJ4
Calculate and compare COP values for Rankine refrigeration cycle and Vapor compression refrigeration cycle. TH=20C and TC=-40C. From HCF-134A CHART
The Rankine refrigeration cycle has a higher COP value than the vapor compression refrigeration cycle. In order to calculate and compare the COP values for the Rankine refrigeration cycle and the Vapor compression refrigeration cycle, we must first define both of these terms.
Rankine refrigeration cycle:
A Rankine refrigeration cycle is a vapor compression refrigeration cycle that utilizes an evaporator, compressor, condenser, and expansion valve to provide cooling. The cycle operates on the Rankine cycle, which is a thermodynamic cycle that describes the behavior of steam as it passes through a steam turbine.
Vapor compression refrigeration cycle:
The vapor compression refrigeration cycle is a common method of refrigeration that utilizes a refrigerant to extract heat from a space or object and transfer it to the environment. The cycle is based on the relationship between pressure, temperature, and energy. As the refrigerant is compressed, its temperature increases. When the refrigerant is expanded, its temperature decreases, resulting in the extraction of heat.
The coefficient of performance (COP) is a measure of the efficiency of a refrigeration system. It is defined as the amount of heat removed from the system per unit of energy input.
The COP of a Rankine refrigeration cycle is given by:
COP Rankine = QL / W = (TH - TC) / (TH - TCL)
Where QL is the heat removed from the refrigeration system, W is the work input into the system, TH is the temperature of the high-pressure side of the system, TC is the temperature of the low-pressure side of the system, and TCL is the temperature of the cooling medium.
Using the HCF-134A chart, we find that the boiling point of HCF-134A at -40°C is approximately 0.27 bar. Therefore, the saturation temperature at the evaporator is -42°C. Similarly, at a condenser temperature of 20°C, the HCF-134A chart gives a saturation pressure of approximately 8.5 bar. Therefore, the saturation temperature at the condenser is approximately 36°C.
Using these values, we can calculate the COP of a Rankine refrigeration cycle:
COP Rankine = (20 - (-40)) / (20 - (-42)) = 60 / 62 = 0.97
The COP of the Rankine refrigeration cycle is 0.97.
The COP of a vapor compression refrigeration cycle is given by:
COP VCR = QL / W = (TH - TC) / (Hin - Hout)
Where Hin is the enthalpy of the refrigerant at the inlet to the compressor and Hout is the enthalpy of the refrigerant at the outlet of the evaporator.
Using the HCF-134A chart, we find that the enthalpy at the inlet to the compressor is approximately 417 kJ/kg, and the enthalpy at the outlet of the evaporator is approximately 133 kJ/kg.
Using these values, we can calculate the COP of a vapor compression refrigeration cycle:
COP VCR = (20 - (-40)) / (417 - 133) = 60 / 284 = 0.21
The COP of the vapor compression refrigeration cycle is 0.21.
Therefore, the Rankine refrigeration cycle has a higher COP value than the vapor compression refrigeration cycle.
Learn more about COP
https://brainly.com/question/28175149
#SPJ11
The quadratic equation x^2−2x+1=0 has discriminant and solutions as follows: Δ=0 and x=−1 Δ=0 and x=1 Δ=0 and x=±1 Δ=4 and x=±1
The solutions to the quadratic equation x^2 - 2x + 1 = 0 are x = -1 and x = 1.
The discriminant (Δ) of a quadratic equation is a value that can be calculated using the formula Δ = b^2 - 4ac, where a, b, and c are the coefficients of the quadratic equation ax^2 + bx + c = 0.
In the given quadratic equation x^2 - 2x + 1 = 0, we can compare it to the general form ax^2 + bx + c = 0 and identify that a = 1, b = -2, and c = 1.
Now, let's calculate the discriminant:
Δ = (-2)^2 - 4(1)(1) = 4 - 4 = 0
The discriminant is zero (Δ = 0).
When the discriminant is zero, it indicates that the quadratic equation has only one real solution. In this case, since Δ = 0, the equation x^2 - 2x + 1 = 0 has two equal solutions.
We can find the solutions by applying the quadratic formula:
x = (-b ± √Δ) / (2a)
Plugging in the values, we have:
x = (-(-2) ± √0) / (2(1)) = (2 ± 0) / 2 = 2 / 2 = 1
So, the solutions to the equation x^2 - 2x + 1 = 0 are x = -1 and x = 1.
Hence, the correct statement is: Δ = 0 and x = ±1.
Learn more about quadratic equation from the given link
https://brainly.com/question/1214333
#SPJ11
A survey of all medium- and large-sized corporations showed that 66% of them offer retirement plans to their employees. Let p be the proportion in a random sample of 40 such corporations that offer retirement plans to their employees. Find the probability that the value of p will be between 0.58 and 0.59. Round your answer to four decimal places. P(0.58 < p < 0.59)
Approximately 0.1138 is the probability that the value of p will be between 0.58 and 0.59.
In a random sample of 40 medium- and large-sized corporations, the proportion of them offering retirement plans to their employees, denoted as p, has a probability of approximately 0.1138 of falling between 0.58 and 0.59. This probability is calculated using the normal approximation to the binomial distribution, assuming that the sample size is large enough and the sampling is done randomly.
To find this probability, we need to convert the proportion p to a standardized score using the formula z = (p - μ) / σ, where μ is the mean and σ is the standard deviation of the distribution.
In this case, the mean μ is equal to 0.66 (given in the survey), and the standard deviation σ is calculated as sqrt([tex](μ * (1 - μ))[/tex] / n), where n is the sample size (40 in this case). By calculating the z-scores for 0.58 and 0.59 and looking up the corresponding probabilities in the standard normal distribution table, we find that the probability of p falling between 0.58 and 0.59 is approximately 0.1138.
Learn more about binomial distribution
brainly.com/question/28031631
#SPJ11
A cone-shaped paperweight is 5 inches tall, and the base has a circumference of about 12.56 inches. What is the area of the vertical cross section through the center of the base of the paperweight?
Answer:
12.57 square inches
Step-by-step explanation:
Given: Height of paperweight (h) = 5 inches, Circumference of base (C) = 12.56 inches.
The formula for circumference of a circle is: C = 2πr, where r is the radius.
Equate the circumference to 12.56 inches: 12.56 = 2πr.
Solve for the radius (r): r = 12.56 / (2π).
Calculate the radius: r ≈ 2 inches.
The formula for the area of a circle is: A = πr^2.
Substitute the radius (r ≈ 2 inches) into the formula: A = π(2^2) = π(4).
Calculate the area: A ≈ 12.57 square inches.
Design a solar power system to your house based on your average monthly consumption. [Number of panels required for your home. Take the peak sun hour as hours and use 350 Watts solar power panels 3. In a city, there are 50,000 residential houses and each house consumes 30 kWh per day. What is the required capacity of the power plant in GWh.
The required capacity of the power plant is 1.5 GWh per day to supply power to 50,000 residential houses, with each house consuming 30 kWh per day.
Solar power system design for a house based on average monthly consumption:The first step is to determine the average monthly power consumption of a home. In this example, we will assume that the monthly power consumption is 900 kWh. The solar power system should produce at least 900 kWh each month to meet this demand. The solar power system will consist of solar panels, an inverter, a battery, and other components.
The number of solar panels required for a home is determined by the solar panel's wattage, the average sun hours per day, and the monthly power consumption. Assume that the peak sun hour is 5 hours and that 350 Watt solar power panels are used.The solar power system's energy production per day can be calculated using the following formula:
Daily energy production (kWh) = Peak sun hours per day x Total system capacity x Solar panel efficiencyTotal system capacity (kW)
= Monthly power consumption (kWh) / 30 days x System efficiencySystem efficiency is assumed to be 0.75 in this example, which is the combined efficiency of the solar panels, inverter, and battery.
Daily energy production (kWh) = 5 x (900 / 30 x 0.75) / (0.35 x 1000)
= 5.86 kWh/day
To produce 5.86 kWh of energy per day using 350 Watt solar panels, the following number of panels is required:
Number of panels = Daily energy production (kWh) / Panel capacity (kW)Number of panels
= 5.86 / (0.35)
= 16.7
≈ 17 panels
Therefore, 17 solar panels are required to power a home that consumes 900 kWh of electricity per month.In a city, there are 50,000 residential houses, and each house consumes 30 kWh per day. The daily energy consumption of 50,000 residential houses is:
Daily energy consumption = 50,000 x 30 kWh/day
= 1,500,000 kWh/day
The required capacity of the power plant can be calculated using the following formula:Required capacity (GWh) = Daily energy consumption (kWh) / 1,000,000 GWh/dayRequired capacity (GWh)
= 1,500,000 / 1,000,000
= 1.5 GWh/day
Therefore, the required capacity of the power plant is 1.5 GWh per day to supply power to 50,000 residential houses, with each house consuming 30 kWh per day.
For more information on solar panels visit:
brainly.com/question/28458069
#SPJ11
Solve the following by False Position Method Question 3 X³ + 2x² + x-1
The approximate solution to the equation x³ + 2x² + x - 1 = 0 using the False Position Method is x ≈ -0.710.
The False Position Method, also known as the Regula Falsi method, is an iterative numerical technique used to find the approximate root of an equation. It is based on the idea of linear interpolation between two points on the curve.
To start, we need to choose an interval [a, b] such that f(a) and f(b) have opposite signs. In this case, let's take [0, 1] as our initial interval. Evaluating the equation at the endpoints, we have f(0) = -1 and f(1) = 3, which indicates a sign change.
The False Position formula calculates the x-coordinate of the next point on the curve by using the line segment connecting the endpoints (a, f(a)) and (b, f(b)). The x-coordinate of this point is given by:
x = (a * f(b) - b * f(a)) / (f(b) - f(a))
Applying this formula, we find x ≈ -0.710.
Learn more about Method
brainly.com/question/14560322
#SPJ11