A 35 kg student bounces up from a trampoline with a speed of 7.4 m/s.
(a) Determine the work done on the student by the force of gravity when she is 1.3 m above the trampoline.
(b) Determine her speed at 1.3 m above the trampoline.

Answers

Answer 1

(a) Therefore, Wg = -(1/2)mv^2where Wg is the work done by gravity on the student. Wg = - (1/2)mv^2 = - (1/2)(35 kg)(7.4 m/s)^2 = -1368.5 J. (b) Therefore, Work done by gravity on the student = -1368.5 J, Speed of the student at 1.3 m above the trampoline = 0 m/s.

Mass of student, m = 35 kg, Speed of the student when he leaves the trampoline, v = 7.4 m/s

Distance between the student and the trampoline, h = 1.3 m

(a) Work done on the student by the force of gravity

when she is 1.3 m above the trampoline. Work done by gravity on the student will be equal to the decrease in the student's kinetic energy. Initial kinetic energy of the student, K1 = (1/2)mv1^2Where v1 is the initial velocity of the student

Final kinetic energy of the student, K2 = 0 (At the highest point, velocity becomes zero)

The work done by gravity, Wg = K1 - K2 = (1/2)mv1^2 – 0 = (1/2)mv1^2The gravitational potential energy of the student at a height h above the trampoline, U1 = mgh

The gravitational potential energy of the student at the highest point, U2 = 0

Therefore, the decrease in gravitational potential energy of the student, U1 - U2 = mgh

Joule’s Law of Work and Energy states that the total work done on an object is equal to the change in its kinetic energy.

The work done by gravity on the student must be equal to the decrease in his kinetic energy.

Wg = -ΔKWhere ΔK is the change in kinetic energy of the student.This equation can be written as follows: Wg = - (Kf - Ki)Where Ki is the initial kinetic energy of the student, and Kf is the final kinetic energy of the student.

The final kinetic energy of the student is zero since he stops at the highest point.

The initial kinetic energy of the student is (1/2)mv^2, where m is the mass of the student and v is his speed just before leaving the trampoline. Therefore, Wg = -(1/2)mv^2where Wg is the work done by gravity on the student. Wg = - (1/2)mv^2 = - (1/2)(35 kg)(7.4 m/s)^2 = -1368.5 J (Negative sign indicates the work done by gravity is in opposite direction to the motion of the student)

(b) Determine her speed at 1.3 m above the trampoline. The speed of the student just before he leaves the trampoline is 7.4 m/s.

When he reaches a height of 1.3 m above the trampoline, his speed will be zero.

This is because at the highest point, the velocity of the student is zero. So, the speed of the student when he is 1.3 m above the trampoline is zero.

Therefore, Work done by gravity on the student = -1368.5 JSpeed of the student at 1.3 m above the trampoline = 0 m/s.

Learn more about work done here:

https://brainly.com/question/32236321

#SPJ11


Related Questions

A rectangular current loop with magnetic moment m=2(x+4y) is present in a uniform Magnetic field with = 4x + 16 y. The Torque acting on the loop is O A. None of the given answers OB.T=136 2 OCT=-136 2 O D, Zero OE T= 8 + 128 y OF T -8- 128 y

Answers

The torque acting on the loop is Option (E) T = 8 + 128y is the correct answer

Given, Magnetic moment m = 2(x + 4y)

Magnetic field B = 4x + 16y

The torque acting on a current loop is given by

T = m × BB = (4x + 16y) = 4xi + 16yj

∴ T = m × B = 2(x + 4y) × (4xi + 16yj) =[tex]8xyi + 32y^2j + 8xyj + 32y(x + 4y)i= 8xyi + 8xyj + 32y^2i + 128y^2j[/tex]

Given, magnetic moment m = 2(x + 4y), so

Torque T = [tex]8xyi + 8xyj + 32y^2i + 128y^2j[/tex]

Therefore, the required torque acting on the loop is

T = [tex]8xyi + 8xyj + 32y^2i + 128y^2j[/tex], which can be written in the form

T = [tex](8x + 32y^2)i + (8x + 128y^2)j[/tex].

Thus, option (F) T = -8 - 128y is incorrect.

In conclusion, the answer is :

The torque acting on the loop is

T = [tex](8x + 32y2)i + (8x + 128y2)j.[/tex]

Hence, option (E) T = 8 + 128y is the correct answer.

learn more about torque here:

https://brainly.com/question/28220969

#SPJ11

The resistivity of a silver wire with a radius of 2.6 mm is 1.59 × 10⁻⁸ m. If the length of the wire is 7 m, what is the resistance of the wire? Give your answer to 4 decimal places in scientific notation.

Answers

The resistance of the silver wire with a radius of 2.6 mm is 5.2395 x 10^-3 Ω.

The radius of the wire (r) = 2.6 mm = 2.6 x 10^-3m

Resistivity of silver wire (ρ) = 1.59 x 10^-8 m

Length of the wire (l) = 7 m

Resistance of a wire (R) = ρ l / A, Where

ρ = Resistivity of the wire

l = Length of the wire

A = Area of cross-section of the wire

A = π r^2 = π (2.6 x 10^-3 m)^2= π (6.76 x 10^-6 m^2) = 2.1257 x 10^-5 m^2

Let's substitute the given values in the above formula and calculate the resistance of the wire.

Resistance of the wire (R) = (1.59 x 10^-8 m x 7 m) / (2.1257 x 10^-5 m^2) = 5.2395 x 10^-3 Ω

Hence, the resistance of the silver wire with a radius of 2.6 mm is 5.2395 x 10^-3 Ω.

Learn more about Resistance https://brainly.com/question/17563681

#SPJ11

show the positioning of an objective lens and eye piece of the following devices with respect to their focal length . example d=fo-fe and number of lens in the device
1. simple microscopic (magnifying glass)
2. compound microscope
3. astronomical telescope
4. galilean telescope
5. prismatic binoculars ​

Answers

1. Simple Microscope (Magnifying Glass): Objective lens = N/A, Eyepiece = N/A (Single Lens)

2. Compound Microscope: Objective lens = Closer, Eyepiece = Farther

3. Astronomical Telescope: Objective lens = Closer, Eyepiece = Farther

4. Galilean Telescope: Objective lens = Closer, Eyepiece = Farther

5. Prismatic Binoculars: Objective lens = Closer, Eyepiece = Farther

Simple Microscope (Magnifying Glass):

In a simple microscope or magnifying glass, there is only one lens, which serves as both the objective lens and the eyepiece. The lens is convex and typically has a short focal length. The object being observed is placed closer to the lens than its focal length (d < fo). So, in this case, the distance between the lens and the object is smaller than the focal length.

Compound Microscope:

A compound microscope consists of two lenses: the objective lens and the eyepiece. The objective lens, with a shorter focal length, is positioned closer to the object being observed. The eyepiece lens, with a longer focal length, is located closer to the observer's eye. The object being observed is placed closer to the objective lens than its focal length (d < fo). The distance between the objective and eyepiece lenses is typically greater than the sum of their focal lengths (d > fo + fe).

Astronomical Telescope:

In an astronomical telescope, the objective lens is positioned closer to the object being observed, such as celestial bodies. The objective lens has a longer focal length compared to the eyepiece lens. The eyepiece lens, with a shorter focal length, is located closer to the observer's eye. The object being observed is placed farther away from the objective lens than its focal length (d > fo). The distance between the objective and eyepiece lenses is typically greater than the sum of their focal lengths (d > fo + fe).

Galilean Telescope:

A Galilean telescope has a convex objective lens and a concave eyepiece lens. The objective lens, with a longer focal length, is positioned closer to the object being observed. The eyepiece lens, with a shorter focal length, is located closer to the observer's eye. The object being observed is placed farther away from the objective lens than its focal length (d > fo). The distance between the objective and eyepiece lenses is typically shorter than the sum of their focal lengths (d < fo + fe).

Prismatic Binoculars:

Prismatic binoculars use multiple lenses and prisms to provide a magnified view. The objective lenses are positioned closer to the observed objects and form real images. These images are then directed through prisms to the eyepiece lenses, which magnify the virtual images seen by the observer's eyes. The distance between the objective and eyepiece lenses is greater than the sum of their focal lengths (d > fo + fe). Prismatic binoculars consist of multiple lenses and prisms for a more complex optical system.

Know more about magnifying glass here:

https://brainly.com/question/20876425

#SPJ8

In the first (simulated) hours and days after striking Earth with Phobos near the Yucatan peninsula, roughly to what temperature does Earth's average air atmosphere rise at maximum before starting to cool back down?

Answers

An asteroid impact on Earth can lead to devastating consequences such as wildfires, tsunamis, and earthquakes. The size of the asteroid determines the extent of the impact, ranging from local destruction to worldwide devastation. The temperature of the Earth's atmosphere can rise to thousands of degrees, causing secondary impacts like firestorms and wildfires.

The initial hours and days after the asteroid impact, Earth's average air atmosphere's temperature rises to thousands of degrees, which can cause the wildfires and secondary impacts that follow.

What happens when an asteroid crashes on Earth?

In general, an asteroid impact can cause fires, a heat wave, or a strong shock wave. The size of the asteroid that crashes determines the impact's aftermath on Earth. Suppose the asteroid is relatively small, say around 40 meters in diameter. In that case, it will likely explode in the atmosphere, causing a meteor airburst that is incredibly destructive but not as catastrophic as the Tunguska airburst.

Astroids impact

When an asteroid of a significant size hits Earth, it can cause worldwide devastation. For instance, the asteroid that caused the extinction of dinosaurs 65 million years ago was about 10-15 kilometers in diameter. It led to a chain of events that wiped out three-quarters of all plant and animal species on the planet.

An asteroid impact can cause massive destruction, including wildfires, tsunamis, and earthquakes. It can also raise the Earth's average air atmosphere's temperature to thousands of degrees, causing secondary impacts like firestorms and wildfires.

Learn more about asteroid impact

https://brainly.com/question/8123911

#SPJ11

An electric iron is Marg 20 words 500 w the units consumed by it in using it for 24 hours will be

Answers

The electric iron with a power rating of 500 watts will consume 12 kilowatt-hours (kWh) of electricity when used continuously for 24 hours.

To calculate the units consumed, we need to consider the power rating and the duration of usage. The power rating of the electric iron is given as 500 watts, which is equivalent to 0.5 kilowatts (kW). By multiplying the power rating by the time used (24 hours), we obtain the total energy consumed, which is 12 kilowatt-hours (kWh). This value represents the units of electricity consumed by the electric iron during the 24-hour period.

Therefore, the electric iron will consume 12 kilowatt-hours (kWh) of electricity when used for 24 hours continuously with a power rating of 500 watts.

Know more about kilowatt here:

brainly.com/question/24057012

#SPJ11

The field-weakening with permanent magnet DC machines would: (a) Increase the speed beyond rated at full armature voltage (b) Decrease the speed (c) Increase mechanical power developed (d) Decrease the torque (e) Neither of the above C24. The rotor of a conventional 3-phase induction motor rotates: (a) Faster than the stator magnetic field (b) Slower than the stator magnetic field (c) At the same speed as the stator magnetic field. (d) At about 80% speed of the stator magnetic field (e) Both (b) and (d) are true C25. Capacitors are often connected in parallel with a 3-phase cage induction generator for fixed-speed wind turbines in order to: (a) Consume reactive power (b) Improve power factor (c) Increase transmission efficiency (d) Improve power quality (e) Both (b) and (c) are correct answers C26. A cage induction machine itself: (a) Always absorbs reactive power (b) Supplies reactive power if over-excited (c) Neither consumes nor supplies reactive power (d) May provide reactive power under certain conditions le) Neither of the above

Answers

C23. In permanent magnet DC machines, the field-weakening operation would increase the speed beyond rated at full armature voltage, and increase the mechanical power developed. Therefore, the correct option is (a) and (c).

C24. In a conventional 3-phase induction motor, the rotor rotates at a slower speed than the stator magnetic field. Therefore, the correct option is (b).

C25. Capacitors are often connected in parallel with a 3-phase cage induction generator for fixed-speed wind turbines to improve power factor and increase transmission efficiency. Therefore, the correct option is (b).

C26. A cage induction machine consumes reactive power when operating under the rated load. Therefore, the correct option is (a).

C23. In permanent magnet DC machines, the field-weakening operation would increase the speed beyond rated at full armature voltage, and increase the mechanical power developed. Therefore, the correct option is (a) and (c).

The field-weakening operation reduces the magnetic field generated by the permanent magnet in DC machines. It is usually applied in electric vehicle applications to reduce the torque and current drawn from the battery, which would extend the operating range of the electric vehicle.

C24. In a conventional 3-phase induction motor, the rotor rotates at a slower speed than the stator magnetic field. Therefore, the correct option is (b).

The relative speed between the rotating magnetic field in the stator and the rotor conductors would generate a rotating torque, which would rotate the rotor.

C25. Capacitors are often connected in parallel with a 3-phase cage induction generator for fixed-speed wind turbines to improve power factor and increase transmission efficiency. Therefore, the correct option is (b).

The capacitor provides a reactive power compensation to balance the reactive power generated by the induction generator. The improved power factor would reduce the power losses and increase the transmission efficiency.

C26. A cage induction machine consumes reactive power when operating under the rated load. Therefore, the correct option is (a).

The reactive power consumption would increase with the increase of the load and reduce with the reduction of the load. The reactive power absorbed by the induction machine would reduce the power factor and reduce the efficiency.

learn more about permanent magnet here:

https://brainly.com/question/14139838

#SPJ11

When the frequency of the AC voltage is doubled, the capacitive reactance whille the inductive reactance halves; doubles doubles; halves halves; halves doubles; doubles

Answers

When the frequency of the AC voltage is doubled, the capacitive reactance halves while the inductive reactance doubles.

When the frequency of the AC voltage is doubled, the capacitive reactance halves while the inductive reactance doubles. This is because the reactance of a capacitor is inversely proportional to the frequency of the AC voltage, while the reactance of an inductor is directly proportional to the frequency of the AC voltage.Capacitive reactance, denoted by XC, is given by the formula:XC = 1 / (2πfC)Where f is the frequency of the AC voltage, and C is the capacitance of the capacitor.

Since the reactance of the capacitor is inversely proportional to the frequency of the AC voltage, when the frequency of the AC voltage is doubled, the capacitive reactance will be halved.On the other hand, inductive reactance, denoted by XL, is given by the formula:XL = 2πfLWhere f is the frequency of the AC voltage, and L is the inductance of the inductor. Since the reactance of the inductor is directly proportional to the frequency of the AC voltage, when the frequency of the AC voltage is doubled, the inductive reactance will be doubled.

In conclusion, when the frequency of the AC voltage is doubled, the capacitive reactance halves while the inductive reactance doubles.

Learn more about frequency here,

https://brainly.com/question/254161

#SPJ11

A physics student notices that the current in a coil of conducting wire goes from 11 = 0.200 A to iz = 1.50 A in a time interval of At = 0.350 s. Assuming the coil's inductance is L = 2.00 ml, what is the magnitude of the average induced emf (in mV) in the coil for this time interval? mV

Answers

The magnitude of the average induced emf in the coil for this time interval is 7.14 mV. The negative sign indicates that the direction of the induced emf opposes the change in current.

The average induced emf (electromotive force) in the coil can be determined using Faraday's law of electromagnetic induction, which states that the induced emf in a coil is equal to the rate of change of magnetic flux through the coil.

The equation for the average induced emf is given by:

ε_avg = -L * (ΔI / Δt)

where ε_avg is the average induced emf, L is the inductance of the coil, ΔI is the change in current, and Δt is the time interval.

Given:

ΔI = 1.50 A - 0.200 A = 1.30 A (change in current)

Δt = 0.350 s (time interval)

L = 2.00 mH = 2.00 × 10^(-3) H (inductance)

Plugging in the values into the formula:

ε_avg = -2.00 × 10^(-3) H * (1.30 A / 0.350 s)

ε_avg = -0.00714 V

To convert the average induced emf to millivolts (mV), we multiply by 1000:

ε_avg = -7.14 mV

Learn more about electromotive force here:

https://brainly.com/question/24182555

#SPJ11

Which of the following could be used to create an electric field inside a solenoid? Attach the solenoid to an AC power supply. Isolate the solenoid. Attach the solenoid to a DC power supply. Attach the solenoid to an ACDC album.

Answers

To create an electric field inside a solenoid, you would need to attach the solenoid to a power supply. However, the type of power supply required depends on the desired type of electric field.

A solenoid is typically used to generate a magnetic field when a current flows through it. If you want to create an electric field inside the solenoid, you would need to change the configuration or introduce additional elements to the solenoid.

The options provided are as follows:

Attach the solenoid to an AC power supply: This option would create an alternating current (AC) flowing through the solenoid, which generates a magnetic field. However, it would not directly create an electric field inside the solenoid.

Isolate the solenoid: Isolating the solenoid, meaning disconnecting it from any power supply, would not generate any electric or magnetic fields.

Attach the solenoid to a DC power supply: This option would create a direct current (DC) flowing through the solenoid, which generates a steady magnetic field. It would not directly create an electric field inside the solenoid.

Attach the solenoid to an ACDC album: This option is not relevant to creating an electric field inside a solenoid. An ACDC album is a music album by a rock band and has no connection to the generation of electric or magnetic fields.

In summary, attaching the solenoid to either an AC or DC power supply can create a magnetic field, but to create an electric field inside the solenoid, you would need to modify the configuration or introduce additional elements to the solenoid setup. The options provided do not directly enable the creation of an electric field inside the solenoid.

Learn more about solenoid here:

https://brainly.com/question/15504705

#SPJ11

Alternating current have voltages and currents through
the circuit elements that vary as a function of time. Is it valid
to apply Kirchhoff’s rules to AC circuits when using rms values for
I and V?

Answers

Kirchhoff's rules can be applied to AC circuits using rms values for current and voltage. RMS values represent the effective values, allowing analysis of current distribution and voltage drops in AC circuits.

It is valid to apply Kirchhoff's rules to AC circuits when using rms (root mean square) values for current (I) and voltage (V). Kirchhoff's rules, which include Kirchhoff's voltage law (KVL) and Kirchhoff's current law (KCL), are fundamental principles that govern the behavior of electrical circuits.

The rms values of current and voltage represent the effective values of the alternating current or voltage. They are calculated as the square root of the average of the squares of the instantaneous values over a complete cycle. By using rms values, we can treat AC circuits in a similar manner to DC circuits.

Kirchhoff's rules state that the algebraic sum of currents at any node in a circuit is zero (KCL), and the algebraic sum of voltages in any closed loop of a circuit is zero (KVL). These rules hold true for AC circuits because they are based on the conservation of charge and energy.

By using rms values, we can effectively analyze and solve AC circuits using Kirchhoff's rules, allowing us to determine current distribution, voltage drops, and power calculations in AC circuits.

To know more about Kirchhoff's rules,

https://brainly.com/question/31824235

#SPJ11

A tiny sphere of mass 7. 70mg and charge −2. 80nC is initially at a distance of 1. 64μm from a fixed charge of +7. 65nC. (a) If the 7. 70-mg sphere is released from rest, find its kinetic energy when it is 0. 500μm from the fixed charge. × J (b) If the 7. 70-mg sphere is released from rest, find its speed when it is 0. 500μm from the fixed charge. M/s

Answers

The kinetic energy of the sphere and its speed can be calculated using the principle of conservation of mechanical energy and the principle of conservation of energy, respectively.

The kinetic energy of the tiny sphere can be found using the principle of conservation of mechanical energy. Initially, the sphere has gravitational potential energy only, given by PE = mgh, where m is the mass (7.70mg), g is the acceleration due to gravity (9.8 m/s²), and h is the initial height (1.64μm).

The final kinetic energy can be calculated by subtracting the final gravitational potential energy (mgh) from the initial potential energy.

At a distance of 0.500μm from the fixed charge, the height can be calculated as h' = (1.64μm - 0.500μm) = 1.14μm.

The final kinetic energy (KE) can be calculated using KE = PE - mgh' where h' is the final height (1.14μm).

To find the speed of the sphere when it is 0.500μm from the fixed charge, we can use the principle of conservation of energy. The initial mechanical energy is equal to the final mechanical energy.

The initial mechanical energy is given by the sum of the initial gravitational potential energy (mgh) and the initial electric potential energy (kQq/r), where k is the Coulomb constant (8.99 x 10⁹ Nm²/C²), Q is the charge of the fixed charge (+7.65nC), q is the charge of the sphere (-2.80nC), and r is the initial distance (1.64μm).

The final mechanical energy is given by the final kinetic energy (KE) and the final electric potential energy (kQq/r'), where r' is the final distance (0.500μm).

Setting the initial mechanical energy equal to the final mechanical energy, we can solve for the speed of the sphere when it is 0.500μm from the fixed charge.

To summarize:
(a) The kinetic energy of the sphere when it is 0.500μm from the fixed charge can be found by subtracting the final gravitational potential energy from the initial potential energy.
(b) The speed of the sphere when it is 0.500μm from the fixed charge can be calculated using the principle of conservation of energy, setting the initial mechanical energy equal to the final mechanical energy.

Conclusion, The kinetic energy of the sphere and its speed can be calculated using the principle of conservation of mechanical energy and the principle of conservation of energy, respectively.

To know more about mechanical energy visit:

https://brainly.com/question/29509191

#SPJ11

An 81 kg person puts on a life jacket, jumps into the water, and floats. The jacket has a volume of 3.1 x 10⁻²m³ and is completely submerged under the water. The volume of the person's body that is under the water is 6.2 x 10⁻² m³. a) What is the buoyant force on the combined man and the life jacket? b) Draw a free body diagram of the forces acting on the person / life jacket. c) What is the density of the life jacket?

Answers

An 81 kg person puts on a life jacket, jumps into the water, and floats. The jacket has a volume of 3.1 x 10⁻²m³ and is completely submerged under the water. The volume of the person's body that is under the water is 6.2 x 10⁻² m³. (a) The buoyant force on the combined person and life jacket is approximately 914.4 N.(c)The density of the life jacket is approximately 2.58 x 10^4 kg/m³.

a) The buoyant force on an object submerged in a fluid is equal to the weight of the fluid displaced by the object. In this case, the buoyant force on the combined person and life jacket is equal to the weight of the water displaced by them.

The volume of the life jacket is 3.1 x 10^(-2) m³, and the volume of the person's body submerged under water is 6.2 x 10^(-2) m³. The total volume of water displaced is the sum of these volumes:

Total volume of water displaced = Volume of life jacket + Volume of submerged body

= 3.1 x 10^(-2) m³ + 6.2 x 10^(-2) m³

= 9.3 x 10^(-2) m³

The density of water is approximately 1000 kg/m³. The weight of the water displaced is equal to the buoyant force:

Buoyant force = Weight of water displaced

= density of water ×volume of water displaced ×acceleration due to gravity

= 1000 kg/m³ × 9.3 x 10^(-2) m³ × 9.8 m/s²

Calculating this, we find:

Buoyant force ≈ 914.4 N

Therefore, the buoyant force on the combined person and life jacket is approximately 914.4 N.

b) The free body diagram of the forces acting on the person and life jacket would include:

   The weight of the person acting downwards (mg).

   The buoyant force acting upwards.

   The normal force exerted by the water surface acting upwards.

   The person's weight acting downwards.

c) To find the density of the life jacket, we can use the formula:

Density = Mass / Volume

The mass of the life jacket is not given directly, but we can calculate it using the weight of the person. The weight of the person is equal to the gravitational force acting on them:

Weight = mass × acceleration due to gravity

Rearranging the formula, we have:

Mass = Weight / acceleration due to gravity

= 81 kg ×9.8 m/s²

Substituting this mass and the given volume of the life jacket into the density formula:

Density = Mass / Volume

= (81 kg × 9.8 m/s²) / (3.1 x 10^(-2) m³)

Calculating this, we find:

Density ≈ 2.58 x 10^4 kg/m³

Therefore, the density of the life jacket is approximately 2.58 x 10^4 kg/m³.

To learn more about buoyant force visit: https://brainly.com/question/11884584

#SPJ11

Look at the names below.
What is the mode?
Millie
Joshua
Lena
Millie
Joshua
Holly
Millie
Oscar
Joshua
Finn
Millie

Answers

Answer:

Mode = Millie

Explanation:

In statistics, the mode is the most frequently occurring value in a set, or, in this case, the most frequent name.

We see Millie 4 times

Joshua 3 times

Lena 1 time

Holly 1 time

Oscar 1 time

And Finn 1 time

Since the name, "Millie", is the most frequent name in the set, that is the mode.

An emf is induced in a conducting loop of wire 1.03 Part A m long as its shape is changed from square to circular. Find the average magnitude of the induced emf if the change in shape occurs in 0.165 s and the local 0.438 - T magnetic field is perpendicular to the plane of the loop.

Answers

The average magnitude of the induced electromotive force (emf) in the conducting loop is approximately 0.497 V when it changes from a square shape to a circular shape in 0.165 s.

The induced emf in a conducting loop is determined by Faraday's law of electromagnetic induction, which states that the emf is equal to the rate of change of magnetic flux through the loop. In this case, the loop changes its shape from a square to a circular shape, and we need to calculate the average magnitude of the induced emf.

The magnetic field is perpendicular to the plane of the loop, which means that the magnetic flux through the loop will be the product of the magnetic field strength and the area of the loop. As the loop changes its shape, the area of the loop also changes.

Initially, when the loop is square, the area is given by A = [tex](1.03m)^{2}[/tex]. When the loop changes to a circle, the area is given by A = π[tex]r^{2}[/tex], where r is the radius of the circle. The average rate of change of the area can be calculated by taking the difference in areas and dividing it by the time taken: ΔA/Δt = [tex]\pi r^{2} - (1.03m)^{2}[/tex] / 0.165 s.

The induced emf is then given by emf = -N dΦ/dt, where N is the number of turns in the loop and dΦ/dt is the rate of change of magnetic flux. In this case, N is assumed to be 1. Substituting the values, the average magnitude of the induced emf is approximately 0.497 V.

Learn more about emf here:

https://brainly.com/question/30893775

#SPJ11

a) A student wants to project the image of an object onto a screen using a curved mirror. The requirement is that the image is magnified. State the type of mirror that would achieve this and carefully describe where the object should be placed with respect to the mirror to achieve the desired image. Proper definitions and terms should be used in your answer. State also, the other characteristics that the image would possess. [2] b) A 1.5 cm high object is placed in front of a convex lens, producing an upright image that is located 8.0 cm from the optical centre of the lens. The focus is located 3.0 cm from the optical centre. Calculate the height of the image.

Answers

a) To achieve a magnified image, a concave mirror should be used. The object should be placed beyond the center of curvature of the mirror.

b) The height of the image formed by the convex lens is 2.5 cm.

a) To achieve a magnified image, a concave mirror should be used. The object should be placed beyond the center of curvature of the mirror. This is because in a concave mirror, the focal point is located between the center of curvature and the mirror's surface. Placing the object beyond the center of curvature ensures that the image formed is larger than the object. The image formed by a concave mirror will be virtual, upright, and magnified.

b) To calculate the height of the image formed by a convex lens, we can use the lens formula:

1/f = 1/v - 1/u

where f is the focal length of the lens, v is the distance of the image from the lens, and u is the distance of the object from the lens.

Given that the focal length (f) is 3.0 cm and the distance of the image (v) is 8.0 cm, we can rearrange the lens formula to solve for u:

1/u = 1/f - 1/v

1/u = 1/3 - 1/8

1/u = (8 - 3)/24

1/u = 5/24

Simplifying, we find that u = 24/5 cm.

Now, we can use the magnification formula:

magnification (m) = height of image (h_i) / height of object (h_o)

Given that the height of the object (h_o) is 1.5 cm, and the height of the image (h_i) is unknown, we can rearrange the formula to solve for h_i:

m = h_i / h_o

m = v / u

Substituting the given values, we have:

m = 8 / (24/5)

m = 8 * (5/24)

m = 5/3

Finally, we can calculate the height of the image:

h_i = m * h_o

h_i = (5/3) * 1.5

h_i = 2.5 cm

Therefore, the height of the image formed by the convex lens is 2.5 cm.

Learn more about magnified image here:

https://brainly.com/question/28791362

#SPJ11

The specific heat capacity of water is 4200 How much heat energy is required to change the temperature of 2.0 Kg of water from 25 degrees * C to 85

Answers

To calculate the amount of heat energy required to change the temperature of 2.0 kg of water from 25°C to 85°C, we can use the equation Q = mcΔT, where Q is the heat energy, m is the mass of the water, c is the specific heat capacity of water, and ΔT is the change in temperature.

To determine the amount of heat energy required, we need to substitute the given values into the equation Q = mcΔT. The mass of the water is given as 2.0 kg, and the specific heat capacity of water is 4200 J/kg°C. The change in temperature, ΔT, can be calculated as the final temperature (85°C) minus the initial temperature (25°C).

Using the equation, we can calculate the heat energy Q by multiplying the mass, specific heat capacity, and change in temperature. The resulting value will be in joules (J) and represents the amount of heat energy required to change the temperature of the water.

Learn more about heat capacity here:

https://brainly.com/question/28302909

#SPJ11

Consider an element (or bubble) of gas rising within a star. Assuming that the element behaves adiabatically as it rises (no heat in or out) and that the surrounding gas is an ideal gas, show that the condition for convection to occur, i.e. for the element to keep rising, can be expressed as:
(d ln T) / (d ln P) = (γ−1) / γ. Hint: consider the appropriate equation of state for the element and the surrounding gas, then compare the expected fractional change of density (drho/rho) of each.

Answers

For convection to occur, the fractional change in density of the rising element must be greater than the fractional change in density of the surrounding gas. This condition is determined by comparing the values of (dlnT/dlnP) for the element and the surrounding gas. If (dlnT/dlnP) is less than (γ-1)/γ, the element will continue to rise, indicating the occurrence of convection.

Consider an element of gas rising inside a star, assuming adiabatic behavior and no heat exchange. In order to demonstrate the occurrence of convection, we must show that the element will continue to rise.

As the element rises through the star, its pressure and temperature decrease. By comparing the fractional changes in density (drho/rho) of the element and the surrounding gas, we can determine the necessary condition for convection.

To begin, let's consider the equation of state for the element and the surrounding gas. The equation of state for an ideal gas is given by PV = nRT, where P represents pressure, V is volume, n is the number of moles, R is the ideal gas constant, and T is temperature. Since the volume of the rising gas bubble is changing, we need to express this equation in terms of density, ρ, where ρ = m/V and m denotes the mass of the gas. Thus, we have: P = ρkT, with k being the Boltzmann constant.

The pressure scale height, Hp, is defined as the distance over which the pressure decreases by a factor of e. This can be expressed as: Hp = P / (dP/dR), where R represents the distance from the center of the star and dP/dR denotes the pressure gradient.

To evaluate the necessary condition for convection, we need to compare the fractional change in density (drho/rho) of the element with that of the surrounding gas. We can express this as: (drho/rho) = (dP/P) / (dR/R) x (1/γ), where γ represents the specific heat ratio. If the fractional change in density is greater for the element compared to the surrounding gas, the element will continue to rise, leading to convection.

Assuming adiabatic rise, we have dP/P = -γdρ/ρ, where the negative sign signifies that pressure decreases as density increases. Combining this with the expression for (drho/rho), we obtain: (drho/rho) = γ / (γ-1) x (dlnT/dlnP).

The element will continue to rise if (drho/rho) is greater for the element compared to the surrounding gas. Therefore, we need to compare the value of (dlnT/dlnP) for the element and the surrounding gas. The element will continue to rise if: (dlnT/dlnP) < (γ-1)/γ.

Learn more about occurrence of convection

https://brainly.com/question/16635311

#SPJ11

An electrical conductor wire designed to carry large currents has a circular cross section with 3.8 mm in diameter and is 28 m long. The resistivity of the material is given to be 1.07×10 −7
Ωm. (a) What is the resistance (in Ω ) of the wire? (b) If the electric field magnitude E in the conductor is 0.26 V/m, what is the total current (in Amps)? (c) If the material has 8.5×10 28
free electrons per cubic meter, find the average drift speed (in m/s ) under the conditions that the electric field magnitude E in the conductor is 2.4 V/m

Answers

(a) The resistance of the wire is approximately 0.200 Ω.

(b) The total current flowing through the wire is approximately 1.300 A.

(c) The average drift speed of the free electrons in the wire, under the given conditions, is approximately 5.647 × 10^(-5) m/s.

(a) To calculate the resistance (R) of the wire, we can use the formula:

R = (ρ * L) / A

where ρ is the resistivity, L is the length of the wire, and A is the cross-sectional area of the wire.

Given that the diameter of the wire is 3.8 mm, we can calculate the radius (r) and the cross-sectional area (A):

r = (3.8 mm) / 2 = 1.9 mm = 1.9 × 10^(-3) m

A = π *[tex]r^2[/tex] = π * (1.9 × [tex]10^{(-3)} m)^2[/tex]

Using the resistivity value (1.07 × 10^(-7) Ωm) and the length of the wire (28 m), we can calculate the resistance:

R = (1.07 ×[tex]10^{(-7)[/tex]Ωm * 28 m) / (π * (1.9 × [tex]10^{(-3)[/tex] [tex]m)^2)[/tex]

R ≈ 0.200 Ω

Therefore, the resistance of the wire is approximately 0.200 Ω.

(b) The total current (I) can be determined using Ohm's law:

I = E / R

where E is the electric field magnitude and R is the resistance.

Given that the electric field magnitude (E) is 0.26 V/m, and the resistance (R) is 0.200 Ω, we can calculate the total current:

I = 0.26 V/m / 0.200 Ω

I ≈ 1.300 A

Hence, the total current flowing through the wire is approximately 1.300 A.

(c) The average drift speed (v) of the free electrons in the wire can be calculated using the formula:

v = (I / (n * A * e))

where I is the current, n is the number density of free electrons, A is the cross-sectional area of the wire, and e is the elementary charge.

Given that the electric field magnitude (E) is 2.4 V/m, and the number density of free electrons (n) is 8.5 × 10^28 electrons/m^3, we can calculate the average drift speed:

v = (2.4 V/m) / (8.5 ×[tex]10^{28} m^{(-3)[/tex] * A * e)

Substituting the known values for the cross-sectional area (A) and the elementary charge (e), we can calculate the average drift speed:

v ≈ 5.647 × [tex]10^{(-5)[/tex] m/s

Therefore, the average drift speed of the free electrons in the wire, under the given conditions, is approximately 5.647 × [tex]10^{(-5)[/tex] m/s.

Learn about resistance  here:

https://brainly.com/question/14547003

#SPJ11

An experiment is performed in deep space with two uniform spheres, one with mass 24.0 kg and the other with mass 110.0 kg. They have equal radii, r = 0.25 m. The spheres are released from rest with their centers a distance 44.0 m apart. They accelerate toward each other because of their mutual gravitational attraction. You can ignore all gravitational forces other than that between the two spheres. Part A When their centers are a distance 29.0 m apart, find the speed of the 24.0 kg sphere. Express your answer in meters per second.
Find the speed of the sphere with mass 110.0 kg kg. Express your answer in meters per second.
Find the magnitude of the relative velocity with which one sphere is approaching to the other. Express your answer in meters per second. How far from the initial position of the center of the 24.0 kg sphere do the surfaces of the two spheres collide? Express your answer in meters

Answers

a) The speed of the 24.0 kg sphere when their centers are 29.0 m apart is approximately 13.03 m/s.b) The speed of the 110.0 kg sphere is approximately 2.83 m/s.c) The magnitude of the relative velocity with which one sphere is approaching the other is approximately 10.20 m/s.d) The surfaces of the two spheres collide at a distance of approximately 3.00 m from the initial position of the center of the 24.0 kg sphere.

a) To find the speed of the 24.0 kg sphere when their centers are 29.0 m apart, we can use the principle of conservation of mechanical energy. The initial potential energy is converted to kinetic energy when they reach this distance. By equating the initial potential energy to the final kinetic energy, we can solve for the speed. The speed is approximately 13.03 m/s.

b) Similarly, for the 110.0 kg sphere, we can use the principle of conservation of mechanical energy to find its speed when their centers are 29.0 m apart. The speed is approximately 2.83 m/s.

c) The magnitude of the relative velocity can be calculated by subtracting the speed of the 110.0 kg sphere from the speed of the 24.0 kg sphere. The magnitude is approximately 10.20 m/s.

d) When the surfaces of the two spheres collide, the distance from the initial position of the center of the 24.0 kg sphere can be calculated by subtracting the radius of the sphere (0.25 m) from the distance between their centers when they collide (29.0 m). The distance is approximately 3.00 m.

Learn more about magnitude here:

https://brainly.com/question/31022175

#SPJ11

An old refrigerator is rated at 500 W. The refrigerator is running 12 hours per day how many kilowatt hours of electric energy would this refrigerator use in 30 days

Answers

The refrigerator would use 180 kilowatt-hours of electric energy in 30 days.

To calculate the kilowatt-hours (kWh) of electric energy used by the refrigerator in 30 days, we need to multiply the power rating of the refrigerator (500 W) by the number of hours it runs per day (12 hours), and then divide by 1000 to convert from watts to kilowatts. Finally, we multiply this value by the number of days (30 days) to get the total energy consumption.

Step 1: Convert the power rating to kilowatts:

500 W ÷ 1000 = 0.5 kW

Step 2: Calculate the daily energy consumption:

0.5 kW × 12 hours = 6 kWh/day

Step 3: Calculate the energy consumption in 30 days:

6 kWh/day × 30 days = 180 kWh

Therefore, the refrigerator would use 180 kilowatt-hours of electric energy in 30 days.

It's worth noting that this calculation assumes that the refrigerator operates at a constant power of 500 W throughout the 12-hour running period. In reality, the power consumption of the refrigerator may vary depending on its operating conditions and efficiency.

For more questions on electric energy, click on:

https://brainly.com/question/60890

#SPJ8

Bear takes his skateboard on a track. He begins from rest at point A. The track he travels on is frictionless, except for a rough patch between points B and C, where the coefficient of kinetic friction is 0.3. If he runs into a spring (Spring constant 300 N/m) at the end of the track, how fare does the string compress? Bear and his skateboard have a combined mass of 2 kg. When bear is on the horizontal part of the track, the normal force from the track on him in 20N.

Answers

Bear and skateboard (2 kg) travel on a frictionless track except for a rough patch. Given normal force (20 N) and spring constant (300 N/m), spring compression distance is not determinable without more information.

To determine how far the spring compresses, we need to consider the conservation of mechanical energy.

First, let's calculate the initial kinetic energy (KE) of Bear and his skateboard. Since he starts from rest, the initial velocity (v) is 0. The initial KE is therefore 0.

Next, let's calculate the final potential energy (PE) stored in the compressed spring. Since the track is frictionless, there is no work done by friction. Thus, all the initial kinetic energy is converted into potential energy in the spring. We can use the equation PE = (1/2)kx^2, where k is the spring constant and x is the compression distance.

Equating the initial kinetic energy to the final potential energy, we have:

0 = (1/2)kx^2

Solving for x, we get:

x = √(0 / (1/2)k)

x = 0

Therefore, the spring does not compress since the initial kinetic energy is completely dissipated due to the friction on the rough patch.

It's important to note that the normal force of 20N on the horizontal part of the track is not directly relevant to the calculation of the spring compression in this scenario.

know more about kinetic energy here: brainly.com/question/999862

#SPJ11

Ignore atmospheric friction, the effects of other planets, and the rutation of the Farth. (Consider the mass of the sun in your ralaulations.) same radial line from the Sunn) X m/s

Answers

Ignoring atmospheric friction, planetary effects, and Earth's rotation, an object moving along the same radial line from the Sun will maintain a constant velocity of X m/s.

When an object moves along the same radial line from the Sun, it experiences a gravitational force directed towards the Sun. According to Newton's second law of motion, this force causes the object to accelerate.

However, in this scenario, we are disregarding atmospheric friction and the effects of other planets, which means there are no external forces acting on the object apart from the gravitational force from the Sun.

Considering the mass of the Sun, the gravitational force experienced by the object can be calculated using Newton's law of universal gravitation. The force of gravity is given by F = (G * M * m) / [tex]r^2[/tex], where G is the gravitational constant, M is the mass of the Sun, m is the mass of the object, and r is the distance between the object and the Sun.

Since there are no other forces involved, the object will continue to accelerate towards the Sun. However, since we are ignoring atmospheric friction and the effects of other planets, the acceleration will not change over time.

Therefore, the object will maintain a constant velocity, determined by its initial conditions, along the radial line from the Sun. The magnitude of this velocity will be X m/s, as specified in the question.

Learn more about velocity here ;

https://brainly.com/question/28738284

#SPJ11

Find the current density of a copper wire with a diameter of 6.4 m and carries a constant current of 9.6 A to a 150-W lamp.

Answers

Therefore, the current density of the copper wire is 3.23 × 104 A/m2.How did you find this solution helpful? Let us know by leaving a comment below!

Current density of a copper wire with a diameter of 6.4 mm and carries a constant current of 9.6 A to a 150-W lamp:Current density is a measure of the quantity of electric charge passing through an area unit per unit time. When a wire of cross-sectional area A carries an electric current I,

the current density J is given by J = I/A. Here, the current density J = ?I/A, where I = 9.6 A is the current flowing in the copper wire and A = 3.22 × 10-8 m2 is the cross-sectional area of the wire. Since the wire is made of copper, which has a density of 8.96 g/cm3, the mass of 1 m of wire can be calculated from the density and cross-sectional area.Mass per metre of wire = Density x Cross-sectional area = 8.96 g/cm3 x 3.22 × 10-8 m2 = 2.89 × 10-6 g/m

The number of moles of copper in 1 m of wire is calculated as follows:Amount of copper = Mass of copper/Molar mass of copper = 2.89 × 10-6 g/63.55 g/mol = 4.55 × 10-8 molThe number of free electrons in 1 mol of copper atoms is known as Avogadro's number, which is roughly 6.02 × 1023. As a result,

the total number of free electrons in 1 m of copper wire can be calculated by multiplying Avogadro's number by the number of moles of copper in 1 m of wire, which is given as:Number of free electrons per metre of wire = Avogadro's number x Amount of copper = 6.02 × 1023 × 4.55 × 10-8 = 2.74 × 1016

The amount of electric charge, q, that passes through the wire per unit time is given by q = It, where t is the time for which the current flows. The power consumed by the 150 W lamp can be calculated using the formula P = VI, where V is the potential difference across the lamp. If we assume that the potential difference across the lamp is 120 V, we haveP = VI = 120 V × 1.25 A = 150 Wwhere I is the current flowing through the wire, which is equal to the current flowing through the lamp, and the factor of 1.25 takes into account the power losses in the circuit.

If the lamp is operated for a period of 10 hours, the amount of electric charge that passes through the wire during this time is given by:q = It = 9.6 A x 10 h x 3600 s/h = 3.46 × 105 CThe current density in the wire can now be calculated using the formula J = q/A.t. Therefore,Current density of copper wire = J = q/A.t = (3.46 × 105 C)/(3.22 × 10-8 m2 x 10 x 3600 s) = 3.23 × 104 A/m2

Therefore, the current density of the copper wire is 3.23 × 104 A/m2.How did you find this solution helpful? Let us know by leaving a comment below!

to know more about density

https://brainly.com/question/1354972

#SPJ11

A 9.5 m long uniform plank has a mass of 13.8 kg and is supported by the floor at one end and by a vertical rope at the other so that the plank is at an angle of 35°. A 73.0-kg mass person stands on the plank a distance three-fourths (3/4) of the length plank from the end on the floor. Include force diagram and equations.

Answers

A 9.5 m long uniform plank has a mass of 13.8 kg and is supported by the floor at one end and by a vertical rope at the other so that the plank is at an angle of 35°. Therefore, the force Fpx required to keep the uniform plank at an angle of 35° is approximately 135.6 N.

The plank is supported by the floor at one end and by a vertical rope at the other so that it is at an angle of 35°.

A person who weighs 73.0 kg stands on the plank at a distance of 3/4 of the length of the plank from the end on the floor.

A 9.5 m long uniform plank has a mass of 13.8 kg. Force diagram: FBD of the plank:

1. Fgx, weight of the plank acts downwards through the centre of gravity of the plank.

2. Fg, weight of the person acts downwards through the center of gravity of the person.

3. Fg, weight of the rope and tension acting upwards

4. Fny, the normal force acting upwards.

5. Fpx, force of plank towards the right.

6. Fpr, force of person towards the right.

7. Fpy, force of person perpendicular to the plank.

Apply the force equation along the vertical axis:

ΣF = 0 = Fny - Fg - Fgx + FgyFny = Fg + Fgx - Fgy ......(i)

Apply the force equation along the horizontal axis:

ΣF = 0 = Fpx + Fpr - FpyFpy = Fpr + Fpx .........(ii)

Finally, apply torque equation about the pivot point which is at the floor end:

Στ = 0 = Fgx×L + Fpy×L/4 - Fg×L/2 - Fpr×L/4Fgx×L + Fpy×L/4 = Fg×L/2 + Fpr×L/4

Substitute the value of Fpy from equation (ii) and simplify:

Fgx×L + (Fpr + Fpx)×L/4 = Fg×L/2 + Fpr×L/4Fgx = (Fg/2) - (Fpx/2) - (Fpr/4)

Substitute Fg = m(g) and rearrange: Fgx = (mg/2) - (Fpx/2) - (Fpr/4) = (13.8 kg × 9.8 m/s²/2) - (Fpx/2) - (73.0 kg × 9.8 m/s² × 3.6 m / 4) = 67.8 N - Fpx/2 - 639.27 N

Therefore, the force Fpx required to keep the uniform plank at an angle of 35° is approximately 135.6 N.

Learn more about gravity  here:

https://brainly.com/question/31321801

#SPJ11

In a RC circuit, C = 4.15microC and the emf of the battery is E= 59V. R is unknown and the time constant is Tau(s). Capacitor is uncharged at t=0s. What is the capacitor charge at t=2T. Answer in microC in the hundredth place.

Answers

The capacitor charge at t = 2T is 3.481 × 10^-6 μC (approx) in the hundredth place.

In an RC circuit,

C = 4.15 microC,

E = 59V

The time constant of the RC circuit is given as τ = RC.

R = unknown Capacitor is uncharged at t = 0 sTo

Charge on a capacitor: Q = Ce^(-t/τ)

Time constant of the RC circuit is given as τ = RC

Therefore, Capacitance C = 4.15 μC, τ = RC = R x 4.15 × 10^-6

And, emf of the battery E = 59V.

Capacitor is uncharged at t = 0 s.

So, the initial charge Qo = 0.

Rearranging Q = Ce^(-t/τ), we get:

e^(-t/τ) = Q / C

To find Q at t = 2T, we need to find Q at t = 2τ

Substituting t = 2τ, we get:

e^(-2τ/τ) = e^(-2) = 0.135Q = Ce^(-t/τ) = Ce^(-2τ/τ)Q = 4.15 × 10^-6 × 59 × 0.135Q ≈ 3.481 × 10^-6 μC

The capacitor charge at t = 2T is 3.481 × 10^-6 μC (approx) in the hundredth place.

Learn more about  Capacitor https://brainly.com/question/21851402

#SPJ11

When your instructor came to your house, she was approaching straight at you on a very fast-moving car and was frantically making a monotone sound with a pipe with one open end and one closed end, whose length was 0.67 m. According to her text message, she was making the 7th harmonic. But to you, it sounded like the sound was in its 9th harmonic. How fast was she moving? Use 343 m/s for the speed of sound. O 76 m/s 0 440 m/s 270 m/s 098 m/s

Answers

The instructor was moving at a speed of approximately 76 m/s.

The frequency of a harmonic in a pipe with one open end and one closed end can be calculated using the formula f = (2n - 1) v / 4L, where f is the frequency, n is the harmonic number, v is the speed of sound, and L is the length of the pipe. In this case, the instructor reported the sound as the 7th harmonic, while the listener perceived it as the 9th harmonic.

Let's set up two equations based on the given information. The first equation represents the frequency reported by the instructor, and the second equation represents the frequency perceived by the listener.

For the instructor: f₁ = (2 × 7 - 1) v / 4L

For the listener: f₂ = (2 × 9 - 1) v / 4L

By dividing the second equation by the first equation, we can eliminate the variables v and L:

f₂ / f₁ = [(2 × 9 - 1) / (2 × 7 - 1)]

Simplifying the equation, we find:

f₂ / f₁ = 17 / 13

Since the speed of sound (v) is given as 343 m/s, we can solve for the ratio of frequencies and find:

f₂ / f₁ = v₂ / v₁ = 17 / 13

Therefore, the ratio of the velocities is:

v₂ / v₁ = 17 / 13

Now we can plug in the given value of v₁ = 343 m/s and solve for v₂:

v₂ = (v₁ × 17) / 13

v₂ = (343 × 17) / 13 ≈ 76 m/s

Hence, the instructor was moving at a speed of approximately 76 m/s.

Learn more about speed here:

https://brainly.com/question/32673092

#SPJ11

T"he naturally occurring electrical field on the ground to an open sky point 3.00 m above is 1.13×10 2
N/C. This open point in the sky is at a greater electric potential than the ground. (a) Calculate the electric potential at this height. (b) Sketch electric field and equipotential lines for this scenario. Calculate the electric potential at this height. (c) Sketch electric field and equipotential lines for this scenario.

Answers

(a) Calculation of electric potential at the height The electric potential at a distance r from a point charge is given by the equation, V=k(q/r)Where V is the electric potential, k is Coulomb’s constant, q is the charge and r is the distance. Now, we will find the potential at a height of 3.00 m from the ground, which is at a distance r=3.00 m from the ground. Q = 0 (as no charge is given)∴ V=0.

(b) Sketch electric field and equipotential lines for this scenario. Equipotential lines and electric field lines are always perpendicular to each other. Equipotential lines represent points on a surface that have the same potential. Hence, the equipotential lines are circular concentric circles around the open point in the sky. The electric field lines start at positive charges and end at negative charges. As no charges are given here, there will be no electric field lines(c) Sketch electric field and equipotential lines for this scenario. The figure shows the electric field lines and equipotential lines. Since there is no charge, the electric field lines will be absent. Equipotential lines will be concentric circles around the open point in the sky at a distance of 3.00 m from the ground.

To know more about charge visit:

https://brainly.com/question/21684715

#SPJ11

A 1000μF capacitor has a voltage of 5.50V across its plates. How long after it begins to discharge through a 1000k2 resistor will the voltage across the plates be 5.00V? Express your answer to 3 significant figures. 330 35D

Answers

Approximately 95.31 seconds after the capacitor begins to discharge through the 1000kΩ resistor, the voltage across its plates will be 5.00V.

To determine the time it takes for a capacitor to discharge through a resistor, we can use the formula for the discharge of a capacitor:

t = RC [tex]ln(\frac{V_{0} }{V})[/tex]

Where:

t is the time (in seconds),

R is the resistance (in ohms),

C is the capacitance (in farads),

ln is the natural logarithm,

V₀ is the initial voltage across the capacitor (in volts), and

V is the final voltage across the capacitor (in volts).

In this case, we have:

C = 1000μF = 1000 × [tex]10^{-6}[/tex] F = 0.001 F,

V₀ = 5.50 V, and

V = 5.00 V.

Substituting these values into the formula, we have:

t = (1000kΩ) × (0.001 F) × ln(5.50 V / 5.00 V)

Calculating this expression:

t ≈ 1000kΩ × 0.001 F × ln(1.10)

Using ln(1.10) ≈ 0.09531:

t ≈ 1000kΩ × 0.001 F × 0.09531

t ≈ 95.31 seconds

Therefore, approximately 95.31 seconds after the capacitor begins to discharge through the 1000kΩ resistor, the voltage across its plates will be 5.00V.

Learn more about resistor here:

https://brainly.com/question/30672175

#SPJ11

Identifying Cassiopeia
Which constellation is Cassiopeia?

Answers

Answer:the answer is the third one

Explanation:

Vector A = 26.0 North
Vector B = 35.0 East
Vector C = 23.0 West
Find the direction of the resultant for A - B. (3 significant figures)

Answers

The direction of the resultant vector for A - B is 35.6° West of North.

Vector A = 26.0 North

Vector B = 35.0 East

Vector C = 23.0 West

The direction of the resultant for A - B will be as follows:

Vector A and Vector B are perpendicular to each other, as Vector A is in the North direction and Vector B is in the East direction.

So, we can use the Pythagorean theorem to find the magnitude of the resultant.

Thus, Resultant vector,

R² = A² + B²  

R = √(A² + B²)

R = √(26² + 35²)  

R = 43.55 units (approx)

As we know that Vector A and Vector B are perpendicular to each other, the angle between them will be 90°.

Now, we can use trigonometric ratios to find the direction of the resultant vector,

tan θ = opposite side/adjacent side

tan θ = A/B  

tan θ = 26/35  

θ = 35.61° (approx)

Hence, the direction of the resultant vector for A - B is 35.6° West of North (3 significant figures).

Learn more about the vectors:

brainly.com/question/30914052

#SPJ11

Other Questions
What is the electron pair arrangement (arrangement of areas of high electron density) of Sel4? (Se in middle, surrounded by I's) linear octahedral t-shaped see-saw bent planar square pyramidal trigonal planar trigonal pyramidal trigonal bipyramidal tetrahedral square planar bent Which is the best summary of Emersons view of solitude expressed in Society and Solitude?Spending time in solitude is more beneficial than spending time in society.Solitude is valuable only when it is balanced with use while in society.Solitude can be beneficial in that it allows the mind to contemplate necessary and difficult questions.Only through spending time in solitude and in deep observation of the natural world can one find happiness within society. Use this abstract to answer questions 6 - 10. Combining regulatory focus theory. (Higgins, 1997) and novelty categorization theory (Forster, Margue & Gillebaart, 2010), we predicted that novel stimull would be more positively evaluated when focused on growth as compared to security. This would occur, at least in part, because of changes in category breadth. Using a subliminal mere exposure paradigm, results showed novel stimuli were evaluated more positively in a promotion focus compared to a prevention focus. For familiar stimuli, ail effects were reversed. We suggest, therefore, that although. familiarity glows warmly in security-related contexts, people generally prefer novelty when they are primarily focused on growth. Modified from: Gillebaart, M., Forster, J. Rotteveel, M. (2010). Mere exposure revisited. The influence of growth versus security cues on evaluations of novel and familiar stimull. Journal of Experimental Psychology General, 1414.699-714 Abstract 2/Question 6 What was were the IV/IVs by name in this experiment? regulatory focus theory and novel categorization theory subliminal mere exposure paradigm Ostimulus familiarity and cu focus Ostimulus familiarity only QUESTION 7 How many IVs were there and how many levels did each have in this experiment? O 1 IV with 4 levels 2 IVs with 2 levels each O2 IVs with 4 levels each that cannot be determined from this abstract QUESTION 8 What is the DV by construct name for this experiment? O mere exposure paradigm evaluation of stimulus novelty of stimuls cue focus QUESTION 9 What is a reasonable operational definition of the DV given the information in this abstract? mere exposure paradigm # of familiar stimuli evaluation rating given to stimulus # of familiar cues QUESTION 10 What is the design for this experiment? posttest only O pre-test/posttest factorial expericorr Compare the relationship between load current, inductor current and capacitor current for buck and boost converter. Use relevant equations to support your explanation where appropriate. [8 marks] (b) The following details are known about a converter: Input voltage of 15V, Rated power of 100W, Output current of 4A, Filter inductance of 100H, Switching frequency of 100kH. Assuming there are no power losses in the converter, determine the following: (i) Input current and output voltage. [4 marks] (ii) The duty cycle. [2 marks] (iii) Inductor peak current. [5 marks] (iv) Whether the converter is operating in continuous mode. [6 marks] [Total 25 marks] Code language : JavaScript#1 - Write a code segment that does the followingDeclares an array of boolean values (true and false). The array should have at least 6 values.Then loop over the elements of the array. Whenever a true value is encountered print "heads" to the console. Whenever a false value is encountered print "tails."Test your function by inspecting the output in the browser console.#2 - Write a code segment that does the following:Declares an array of numbers. The array should have at least 5 values.Then loop over the array and calculate the sum of all values in the array.Once the loop has completed, print the sum you calculated.Note: This sum should only be printed once, when the loop ends.Hint: You will need a temporary variable to hold the sum of values in the array#3 - Write a code segment that does the following:Declares an array of numbers. The array should have at least 10 values.Then loop over the array and find the largest element in the array.Once the loop has completed, print the largest element.Note: This largest element should only be printed once, when the loop ends.Hint: You will need a temporary variable to hold the largest element seen in array.#4 - Write a code segment that does the following:Declares an array of strings. The array should contain your 5 favorite names.Sort the array using the sort() function. You can read more about this function here (Links to an external site.).Then, using a loop, print the elements in sorted order to the browser console.#5 - Write a code segment that does the following:Declares an array of strings. The array should contain your top-10 favorite movie titles.Then loop over the array and find the movie title with the lowest number of characters.Note: You can use the String.length property to determine how long each string is. Here is a tutorial (Links to an external site.) on String.length.Once the loop has completed, print the movie title with the lowest number of characters.. A biomass company plans to build a commercial torrefaction plant in British Columbia, Canada, to utilize the beetle-infested pine forest. This waste product contains 35% moisture (M) on "as-received" basis. The composition of the feed on "dry basis" is as below: Proximate analysis (db): Volatiles: 80.71%, fixed carbon: 16.16%, ash: 3.13%. Ultimate analysis (db): C: 47.99%, H: 6.25%, O: 40.73%, N: 1.31%, S: 0.58%, ASH: 3.13%. Pilot plant tests suggested an optimum torrefaction temperature and residence time for the biomass as 280C and 20 min, respectively, such that 20% of the dry biomass is converted into volatiles carrying 5% of the total thermal energy. Calculate 1. The lower and higher heating value (HHV) of the biomass feed on (a) wet basis, (b) dry basis, and (c) dry ash free basis. 2. Mass yield on dry basis and on dry ash free basis. Example 4.2 Using data from Example 4.1, calculate the following: a. Energy yield on "dry" and "dry ash free" basis. b. HHV of torrefied biomass on "dry" and on "dry ash free" basis. Example 4.4 Design a moving bed torrefier to produce 1 ton/h (daf) of torrefied biomass from raw biomass containing 30% moisture but negligible amount of ash. Torrefaction at 280C yields 70% mass (daf). Biomass and air enter the unit at ambient temperature of 20C. Hot gas leaves torrefier at 105C. Select all the correct answers. Which two types of waves can transmit energy through a vacuum? a. radio waves b. seismic waves c. sound waves d. water wavese. x-rays Evaluate and Solve for all solutions of x over the domain 0x2. Use 5ACT valuen IF POSSTBUE. If not possible, round your final answer to 2 decimal placec. Show your work for full marks. [4] merks each total [0] marks a) 2sin^2(x)sin(x)1=0 b) 6sin^2(x)sin(x)1=0 41. What is double depression?a. Two depressive episodes that occur within one month of each other, with an interval of normal mood inbetweenb. A depressive episode that occurs during a dysthymic (persistent depressive disorder) episodec. Depression that occurs in monozygotic twins raised apart, or dizygotic (fraternal) twinsd. The depression that immediately follows a manic episode in bipolar disorder Problem-Solving Session 7: Second-Order Circuits The switch has been in its starting position for a long time before moving at t = 0. Determine i(0+), V(0*), dv 0+) and + Find i(t) and v(t) for t 0+. 20V 37502 www 0.5F t=0 v(t) i(t) 250 80 mH 500 25mA M7L1 - Does Wal-Mart Suppress Competition?Wal-Mart is often the target of angry consumers who feel that the nations largest retailer causes smaller "mom and pop" businesses to close their doors because they cannot compete on price.PART IAnswer the following question: Does Wal-Mart intentionally undermine small retailers to put them out of business, or is the failure of these competitors simply a result of the large economies of scale that Wal-Mart has? Please be clear and RESPECTFUL in your explanation What are some of the techniques of Chopin's piano compositionsthat clearly break away from the musical style of the Classicalperiod? Legal Environment of BusinessRead the Information Technology section on page 80. Then give your opinion, with justification, to the question of Should 1st Amendment rights extend to violent video games? Please be sure to present specific facts of the case to support your argument. Think about this in light of the Court's decision in the Packingham case USA regarding the 1st amendment and your own opinions. Information Technology Free Speech and Video Games And whatever the challenges of applying the Constitution to ever-advancing technology, the basic principles of freedom of speech and the press do not vary when a new and different medium for communication appears." -Scalia, Justice Video games are played by millions of youth and adults. Some of the games contain violent content. The state of California enacted a state statute that prohibits the sale or rental of "violent video games" to minors. The act covers games in which the range of options available to a player includes killing, maiming, dismembering, or sexually assaulting an image of a human being. Violation of the act is punishable by a civil fine of up to $1,000. Members of the video game and software industries challenged the enforcement of the act, alleging that the state law violated their constitutional free speech rights. The U.S. Supreme Court held that the California act violated the Free Speech Clause of the First Amendment to the U.S. Constitution. The Supreme Court stated, Whatever the challenges of applying the Constitution to ever-advancing technology, the basic principles of freedom of speech and the press do not vary when a new and different medium for communication appears. Certainly the books we give children to read-or read to them when they are younger-contain no shortage of gore. As her just deserts for trying to poison Snow White, the wicked queen is made to dance in red hot slippers. Cinderella's evil stepsisters have their eyes pecked out by doves. And Hansel and Gretel (children!) kill their captor by baking her in an oven. The U.S. Supreme Court held that California had singled out the purveyors of video games for disfavored treatment at least when compared to booksellers, cartoonists, and movie producers- and has given no persuasive reason why. Brown, Governor of California v. Entertainment Merchants Association, 564 U.S. 786, 131 S.Ct. 2729, 2011 U.S. Lexis 4802 (Supreme Court of the United States, 2011) From the following Trial Balance of ZeeP Ltd for the year ended 31st March 2014, prepare the Income Statement and Balance Sheet.Particulars Opening StockPlant and MachineryFurniture and fixturesFreehold PremisesPurchasesSalariesSundry DebtorsManufacturing WagesMaintenance ExpensesCarriage InwardsCarriage Outwards Other ExpensesBad DebtsInterest and Bank ChargesRentInsurance Premium PaidCash at BankCash at handCommon Stock 90,000Sundry CreditorsDiscount ReceivedBank overdraftPurchase ReturnsSalesAmt45,00085,0007,500 75,0001,50,00014,00055,00030,00015,0002,0002,10010,0007506257501,50069515043,0003,50020,0001,5003,37,070Adjustments: Closing Stock - Rs 57000; Insurance Prepaid - Rs 500 Salary paid in advance - Rs 600; Outstanding interest on overdraft - Rs 1000 Rent unpaid - Rs 400 Depreciation in plant and machinery - 10% p.a Depreciation on furniture and fixtures - 20% p.a The output of a station with two alternators in parallel is 40MW at 0.75 power factor lagging. One machines is loaded to 20,000KW at 0.8 power factor lagging. Determine the: a. KVA rating and power factor of the load b. KVA rating and power factor of the other alternator For the reaction below, the thermodynamic equilibrium constant is K= 2.3010 at 25 C. NH4CO2NH(s) 2 NH3(g) + CO2(g) Suppose that 0.007 moles of NH4CO2NH2, 0.014 moles of NH3, and 0.007 moles of CO are added to a 9.00 L container at 25 C. (a) What are Q and ArG for the initial reaction mixture? Your answers must be accurate to 3 significant figures. Q = Number ArG = Number kJ mol-1 (b) Is the spontaneous reaction to the left or to the right? Solve the given Differential Equation by Undetermined Coefficient - Annihilator Approach. y"" + 16y" = xsin4x Consider an amino acid sequence: D1-G2-A3-E4-C5-A5-F7-H8-Rg. 10-A11-H12-T13-Y14-G15-P16-F17-E18-A19-A20-M21-C22-K23-W24-E25-A26-Q27- P28 The addition of CNBr will result in (put down a number) peptide fragment(s). The B-turn structure is likely found at (Write down the residue number). A possible disulfide bond is formed between the residue numbers and The total number of basic residues is The addition of trypsin will result in The addition of chymotrypsin will result in (put down a number) peptide fragment(s). (put down a number) peptide fragment(s). The RASCI model is helpful for the account manager when they prepare a(n)... Yantnz: Conference Report PPM (shooting) Meeting Timesheets Status Report Yant temizle Discuss the role of women and how their lives have changed between the years, 1815 to the present (2022).What are the most important developments, and how did they occur? Why did these changes not happen earlier?