The formula for the impulse exerted on the ball from the instant it is dropped to an arbitrary time later is:
Impulse = (Final momentum - Initial momentum)
What is impulse?Impulse is a vector quantity having both magnitude and direction, whereas momentum is a vector quantity, but the impulse is not equal to momentum. The impulse is the change in momentum.
If a ball of mass m is dropped from rest, then its initial momentum is zero.
The final momentum of the ball after falling for time t is:
Final momentum = mv
Where v is the velocity of the ball after falling for time t.
Therefore, the impulse exerted on the ball from the instant it is dropped to an arbitrary time later is:
Impulse = (mv - 0) = mv
To know more about impulse:
https://brainly.com/question/14073258
#SPJ11
determine the amount of heat transfer required when this is done during a constant-volume process. (you must provide an answer before moving on to the next part.)
The amount of heat transfer that is required when the process is done during a constant - volume process is 64, 921. 00 Joules
How to find the amount of heat transfer ?To find the amount of heat transfer during a constant-volume process, for a diatomic gas, the formula is :
= 5 / 2 x R
Expanded, this is:
Heat transfer = n Cv Δ T
The amount of heat transfer is therefore :
= ( 1, 000 / 32 ) x ( 5 / 2 R ) x ( 120 - 20 )
= ( 1, 000 / 32) x ( 5 / 2 x 0. 31) x 100
= 64, 921. 00 Joules
Find out more on the constant-volume process at https://brainly.com/question/30891992
#SPJ1
The full question is:
1 kg of oxygen is heated from 20 to 120°C. Determine the amount of heat transfer required when this is done during a constant-volume process.
determine the magnitude and direction of the magnetic field produced by this electric power line at earth's surface directly under the wire.
The magnitude and direction of the magnetic field produced by the electric power line at earth's surface directly under the wire is dependent upon the current running through the wire. The direction of the magnetic field can be determined by using the right hand rule. Place your right hand with the thumb pointing in the direction of the current flow, the fingers will curl in the direction of the magnetic field.
The electric field produced by an electric power line is determined by the voltage of the power line, with the electric field intensity being proportional to the voltage of the power line.
The direction of the electric field can be determined using the left hand rule; place your left hand with the thumb pointing in the direction of the current flow, the fingers will curl in the direction of the electric field.
Know more about magnetic field here:
https://brainly.com/question/23096032
#SPJ11
which stereo microphone technique works only from level differences produced by off-axis attenuation and not from difference in time delay
The stereo microphone technique that works only from level differences produced by off-axis attenuation is called Mid-Side (M-S) stereo recording.
Mid-Side (M-S) stereo recording technique utilizes two microphones, one of which is pointed directly at the sound source and the other pointing 90 degrees to the left or right. The result is two channels of audio which are then combined in the mixing process to create a full stereo image. The two signals have a 3 dB difference in level between them, with the off-axis microphone being the lower of the two. This level difference produces the stereo image and is the only factor used in M-S stereo recording. Time delays are not used in this technique, as the level differences are sufficient to create the stereo image.
M-S stereo recording has a number of benefits, such as being able to adjust the width of the stereo image in the mixing process, and allowing for mono compatibility. It is therefore a great choice for stereo recordings that need to be heard in both mono and stereo, such as live broadcasts or online streams.
For more such questions on Microphone.
https://brainly.com/question/29421910#
#SPJ11
a cardiac pacemaker can be affected by a static magnetic field as small as 1.7 mt. how close can a pacemaker wearer come to a long, straight wire carrying 16 a?
A cardiac pacemaker wearer can come up to 0.1 meters (10 cm) away from a long, straight wire carrying 16 amperes (A).
It is important to note that the exposure limits were set for the general population and not for pacemaker wearers specifically. However, pacemaker wearers should take extra precautions to avoid electromagnetic fields that could potentially affect their device. There are certain areas and equipment that can generate strong magnetic fields such as MRI machines, metal detectors, and some industrial machinery that pacemaker wearers should avoid.
There are certain materials that can shield pacemakers from electromagnetic fields such as aluminum and copper mesh clothing. Pacemaker wearers should also consult with their healthcare provider to determine any additional precautions they should take.
The field strength of a long, straight wire carrying 16 A is calculated by using the equation,
B = (μ₀ * I) / (2 * π * r)
Where, B = magnetic field strength , μ₀ = magnetic constant
(4π x 10^-7 Tm/A)I = current (16 A)r = distance from the wire (unknown)
Rearranging the formula,
r = (μ₀ * I) / (2 * π * B)
Substituting the values, r = (4π × 10^-7 Tm/A × 16 A) / (2 × π × 1.7 × 10^-3 T) r = 0.1 m or 10 cm.
for such more question on cardiac pacemaker
https://brainly.com/question/14980296
#SPJ11
a 70.0-g arrow, fired at a speed of 115 m/s to the left, impacts a tree, which it penetrates to a depth of 12.2 cm before coming to a stop. assuming the force of friction exerted by the tree is constant, what are the magnitude and direction of the friction force acting on the arrow?
The magnitude of the friction force is 0.788 N and it is directed to the right.
The friction force acting on the arrow is equal to the force required to stop the arrow and is directed opposite the direction of motion.
The magnitude of the friction force is equal to the product of the mass of the arrow (70.0 g) and the deceleration of the arrow (11.2 cm/s^2).
When the arrow hits the tree, the friction force of the tree will slow down the arrow's motion. The magnitude of this friction force is equal to the product of the mass of the arrow (70.0 g) and the deceleration of the arrow (11.2 cm/s^2).
The direction of the friction force will be opposite to the direction of the arrow's motion.
Therefore, the magnitude of the friction force is 0.788 N and it is directed to the right. This is because the arrow was fired to the left and the friction force must be equal and opposite in order to bring the arrow to a stop.
To know more about friction force click on below link:
https://brainly.com/question/30280752#
#SPJ11
true or false: electrically neutral objects have no positive or negative charges, that is why they are neutral
True, electrically neutral objects have no positive or negative charges, that is why they are neutral.
Electrically neutral objects have an equal number of protons and electrons, so the total charge on the object is zero. This is why we refer to the object as being ‘neutral’. It has no charge.
In a chemical reaction, protons are transferred between particles, such as atoms or ions. When an atom loses or gains protons, its charge changes, either becoming more negative or more positive.
An atom which has the same number of protons and electrons has a net charge of zero and is neutral.
In an electric field, a neutral object experiences no force due to the absence of electric charge on its surface. When placed in a magnetic field, however, a neutral object still experiences a force due to its electrons.
Electrons have a magnetic moment, so they are affected by the magnetic field, causing the neutral object to move.
Electrically neutral objects have no positive or negative charges, that is why they are neutral.
Their charge is zero, so they are not affected by electric fields, but still experience a force in a magnetic field due to the magnetic moment of their electrons.
to know more about neutral refer here:
https://brainly.com/question/15395418#
#SPJ11
Can anyone help please
The total energy of the block when it is 5 cm away from the mean position is 0.25 J.
How to calculate the energyThe potential energy of the spring is given by the equation:
U = (1/2)kx²
where k is the spring constant and x is the displacement from the equilibrium position.
In this problem, the block is pulled to a distance x = 10 cm from its equilibrium position, so the potential energy stored in the spring is:
U = (1/2)(50 N/m)(0.1 m)² = 0.25 J
When the block is 5 cm away from the mean position, its displacement from the equilibrium position is x = 0.05 m. Therefore, the potential energy stored in the spring is:
U = (1/2)(50 N/m)(0.05 m)² = 0.0625 J
(a) At t = 0, the block is at rest, so its kinetic energy is zero. When the block is 5 cm away from the mean position, it has a certain velocity, which we can find using conservation of energy. The total energy of the system is conserved, so the sum of the kinetic and potential energies is constant. The kinetic energy at this point is:
K = E - U = 0.25 J - 0.0625 J = 0.1875 J
(b) We have already calculated the potential energy at this point, which is U = 0.0625 J.
(c) The total energy of the system at this point is the sum of the kinetic and potential energies, which we have calculated in parts (a) and (b):
E = K + U = 0.1875 J + 0.0625 J = 0.25 J
Therefore, the total energy of the block when it is 5 cm away from the mean position is 0.25 J.
Learn more about energy on
https://brainly.com/question/13881533
#SPJ1
Question about my assignment
Answer: A - Gold Foil Experiment
Explanation:
Answer:
A
Explanation: Rutherford's gold foil experiment.
what do you think the forces are on the fan cart are on the frictionless surface vs. on the wooden surface?
When the fan cart is on a frictionless surface and a wooden surface, the forces acting on it are different. When the fan cart is placed on a frictionless surface, the force acting on it is the thrust force created by the fan, and there is no friction.
On the other hand, when the fan cart is placed on a wooden surface, the force acting on it is the thrust force created by the fan, and there is friction between the cart and the surface. Due to the presence of friction, the fan cart may take longer to come to a stop when placed on a wooden surface. The amount of friction acting on the fan cart on the wooden surface depends on the type of surface and the force of the thrust created by the fan.
When there is no friction on the surface, the cart will move without being interrupted, whereas when the cart is placed on a wooden surface, friction will act against it. The frictional force will vary based on the type of surface and the force exerted by the thrust generated by the fan.
Therefore, the forces acting on the fan cart will be different based on the surface it is placed on. When it is on a frictionless surface, there is no friction acting on it, and when it is on a wooden surface, there is a force of friction acting against it.
Read more about friction:
https://brainly.com/question/24338873
#SPJ11
The grades received by 10 college sophomores in a test are A, B, D, A, A, A, C, B, C, and A. From this data, it can be inferred that the mode is _____.
It can be inferred that the mode is A from the data about grades.
In statistics, the mode in a given data set is the value or set of values that occur most frequently in the data set. The grades received by ten college sophomores in a test are A, B, D, A, A, A, C, B, C, and A. From this data, it can be inferred that the mode is A, which occurs five times.
It can also be noticed that the frequency of sophomores receiving grades B, C, and D is 2, 2, and 1, respectively. Since grade A occurs most frequently (5 times) in the given data set, therefore, it can be inferred that the mode of the data set is A.
Learn more about data: https://brainly.com/question/27358262
#SPJ11
over what locations on earth can a satellite be placed in a geostationary orbit? please give your reasoning, including an illustrative diagram.
Locations on earth can a satellite be placed in a geostationary orbit over the equator of the earth
The geostationary orbit is a circular orbit located above the earth's equator at a height of around 36,000 km or 22,000 miles. The satellite is always positioned in a fixed point in the sky from the earth. The satellite remains fixed in the sky above a particular location on the earth's surface.In other words, it has an orbital period equal to the rotation of the Earth on its axis. This type of orbit is used for communication, weather forecasting, and remote sensing because it allows the satellite to remain fixed in the same position above the earth.
As a result, they offer a stable platform for communication with the earth.The geostationary orbit has numerous benefits. For instance, it reduces the required power of communication equipment, ensuring that a small antenna can receive or transmit signals to a satellite with less power. It also allows for a full view of the earth's surface, thereby providing comprehensive coverage for communication, broadcasting, and other satellite applications. The diagram below shows a satellite placed in a geostationary orbit. Therefore, to place a satellite in a geostationary orbit, it must be placed over the equator of the earth.
Learn more about geostationary orbit at:
https://brainly.com/question/29091189
#SPJ11
Which are true about Halogens? (please choose all that apply)
a) Reactive
b) Group 7A
c) Non-metals
d) Metals
e) Non-reactive
Answer:
the answer is a number
Explanation:
support me
2. car 1 has 2 times the mass of car 2, but only 0.3 as much kinetic energy. what is the ratio between the speeds of the two cars (vi/v2)? you must type your answer as a numerical value.
The ratio of the speeds of the two cars is approximately 0.387.
The kinetic energy of an object is given by the formula:
KE = 0.5 * m * v²
where KE is the kinetic energy, m is the mass, and v is the velocity of the object.
Let's denote the mass of car 2 as m, and the mass of car 1 as 2m (since car 1 has 2 times the mass of car 2).
We are told that the kinetic energy of car 1 is only 0.3 times that of car 2:
0.5 * (2m) * v1 = 0.3 * 0.5 * m * v2^2
Simplifying this equation, we get:
2 * v1² = 0.3 * v2²
Dividing both sides by v2², we get:
2 * (v1/v2)² = 0.3
Solving for the ratio of velocities, we get:
v1/v2 = [tex]\sqrt{(0.3/2) }[/tex]= 0.387
Learn more about The kinetic energy: https://brainly.com/question/26472013
#SPJ11
A baseball collides with a baseball glove. Which equation is used to calculate the force the glove exerts on the ball during the collision?force = mass × velocity
force = weight × acceleration
force = weight × velocityforce = mass × acceleration
The equation used to calculate the force the glove exerts on the ball during the collision is force = mass × acceleration. This equation relates the force exerted on an object to its mass and the acceleration it experiences.
During the collision, the ball experiences a change in velocity, which corresponds to an acceleration. The force exerted by the glove on the ball is equal in magnitude but opposite in direction to the force exerted by the ball on the glove, as described by Newton's third law of motion.
The force exerted on the ball is what causes it to change direction and slow down, ultimately leading to it coming to a stop in the glove. It's important to note that while the velocity of the ball is involved in the collision, it is not directly used to calculate the force.
Instead, the mass and acceleration of the ball are used in conjunction with the force equation to determine the force exerted by the glove on the ball. This equation can also be used in other scenarios where an object experiences a force due to acceleration, such as a car accelerating or a person jumping.
For more details about acceleration click here:
https://brainly.com/question/12550364#
#SPJ11
which of the following increase the centripetal force? 1. increasing the radius 2. decreasing the acceleration 3. decreasing the mass 4. increasing the velocity
The correct option is 4, increasing the velocity (v) will result in an increased centripetal force (F).
What is centripetal force?
Centripetal force is the force that acts on a body traveling in a circular path, holding it back toward the center of the circle. It's worth noting that the centripetal force is not distinct. Instead, it's the net force acting on the body, which is always perpendicular to the body's motion direction in a circular path.
Effect of velocity on centripetal force:
Increasing the velocity increases the centripetal force. The centripetal force is proportional to the square of the velocity (Fc = mv²/r). Therefore, if the velocity is increased, the centripetal force will be increased as well. On the other hand, if the radius is increased, the centripetal force will be decreased (Fc = mv²/r). As a result, increasing the radius is the opposite of increasing the velocity in terms of the effect on the centripetal force.
Decreasing the mass will also increase the centripetal force (Fc = mv²/r). Therefore, option 3 is incorrect. Similarly, decreasing the acceleration (option 2) will decrease the centripetal force because the force required to sustain a circular path is proportional to the square of the acceleration (Fc = ma). As a result, decreasing the acceleration would decrease the centripetal force, and thus option 2 is incorrect. In conclusion, among the given options, increasing the velocity is the only one that increases the centripetal force.
To know more about centripetal force, visit:
https://brainly.com/question/11324711
#SPJ11
an unspecified force causes a 0.10-kg object to accelerate at 0.30 m/s2. if 0.40 kg is added to the 0.10-kg object and the force remains the same, what is the acceleration (in m/s2) of the heavier object? (never include units with the answer to a numerical question.)
The acceleration of the heavier object can be calculated by rearranging the equation for Force (F) = Mass (m) x Acceleration (a). The force in the original problem was 0.10 kg, with an acceleration of 0.30 m/s2. When the mass of the object is increased to 0.50 kg, the acceleration of the heavier object becomes 0.20 m/s2.
To calculate this, we can divide both sides of the equation by the mass, producing: a = F / m. We can then substitute in the values from the original problem, 0.10 kg for the mass and 0.30 m/s2 for the acceleration, giving us 0.30 m/s2 = F / 0.10 kg. When we increase the mass to 0.50 kg, we can rearrange this equation to give us the acceleration of the heavier object, a = F / 0.50 kg, resulting in 0.20 m/s2.
Know more about Force here
https://brainly.com/question/13191643#
#SPJ11
The bob of a pendulum is released from a horizontal position. If the length of the pendulum is 1.5m, what is the speed with which the bob arrives at the lowermost point, given that it dissipated 5% of its initial energy against air resistance ?
The speed at which the bob reaches the lowest point is 3.54 m/s
When the bob is released from the horizontal position, its potential energy is maximum, and kinetic energy is zero. So, the initial energy of the pendulum is the potential energy it has when it is released. The formula to calculate the potential energy of the pendulum is given by: PE = mgh
Where m is the mass of the bob, g is the acceleration due to gravity, and h is the height of the bob above the lowermost point. At the lowermost point, the potential energy is zero, and the kinetic energy is maximum.
Therefore, the kinetic energy at the lowermost point is equal to the initial potential energy of the pendulum. The formula for kinetic energy is given by:
KE = (1/2)mv² Where m is the mass of the bob, and v is the velocity of the bob at the lowermost point. Since energy is conserved, the initial potential energy of the pendulum is equal to the final kinetic energy of the bob. However, some of the initial energy is dissipated against air resistance. So, we can write the equation as:
PE - 5% PE = KE,
mgh - 0.05mgh = (1/2)mv²,
v² = 2gh(1 - 0.05),
v² = 2 × 9.8 × 1.5 × 0.95,
v = 3.54 m/s
Therefore, the speed with which the bob arrives at the lowermost point is 3.54 m/s.
To know more about pendulum click on below link :
https://brainly.com/question/30528375
#SPJ11
Listed in the Item Bank are key terms and expressions, each of which is associated with one of the columns. Drag and drop each item into
the correct column. Order does not matter.
Conductor or Insulator
:: aluminum foil
:: plastic :: ocean water
:: air
:: wood
:: soil
:: foam
glass
Conductor:
Aluminum foil
Insulator:
Plastic
Air
Wood
Soil
Foam
Glass
What is Conductor?
A conductor is a material or substance that allows electric charge to flow freely through it, offering little or no resistance to the flow of an electric current. Common conductors include metals such as copper, silver, and gold.
A conductor is a material or substance that allows electrical current to flow freely through it. This is due to the presence of free electrons that can move easily through the material when an electric field is applied. Common conductors include metals such as copper, silver, and aluminum.
In contrast, an insulator is a material or substance that does not allow electrical current to flow through it easily. Insulators have very few free electrons and resist the flow of electric current. Common insulators include rubber, plastic, glass, and air.
Learn more about Conductor from given link
https://brainly.com/question/24154868
#SPJ1
ay telescope mirrors are arranged in a way very similar to optical telescope mirrors. group of answer choices true false
Telescope mirrors are arranged in a way very similar to optical telescope mirrors is a True statement.
The Telescopes and optical telescope can also be used as
Telescopes: Telescopes, including optical telescopes, use mirrors or lenses to collect and focus light. Optical telescope: Optical telescope mirrors are usually curved in shape to reflect light from distant objects and form an image at the focal point.Similarly, other types of telescopes such as radio telescopes, infrared telescopes, and ultraviolet telescopes also use mirrors to collect and focus the corresponding wavelengths of light they are designed to detect.
To learn more about the 'optical telescope':
https://brainly.com/question/18300677
#SPJ11
a tiny neutrally buoyant electronic pressure probe is released into the inlet pipe of a water pump and transmits 2000 pressure readings per second as it passes through the pump. is this a lagrangian or an eulerian measurement?
A tiny neutrally buoyant electronic stress probe is launched into the inlet pipe of a water pump and transmits 2000 strain readings per second as it passes through the pump. This is a lagrangian measurement.
Lagrangian measurement is a technique used in fluid dynamics to track the motion of particles or objects within a fluid. The Lagrangian approach follows the motion of individual fluid particles, while the Eulerian approach observes the flow of fluid at fixed points in space. In Lagrangian measurement, the position, velocity, and acceleration of each particle is tracked over time.
Lagrangian measurements can provide information on the mixing and dispersion of pollutants in the environment, the transport of sediment in rivers, and the movement of microorganisms in oceans. Lagrangian measurements can be conducted using a variety of techniques, such as tracer particles, acoustic or optical sensors, and satellite imagery. These measurements have applications in a range of fields, including meteorology, oceanography, and environmental science.
To learn more about Lagrangian visit here:
brainly.com/question/28357993
#SPJ4
a portable cd player uses a current of 7.5 ma at a potential diference of 3.5 v. how much energy does the player use in 35 s?
A portable CD player uses 7.5mA of current at a potential difference of 3.5V. Since it is running for 35 seconds, the total energy consumed in that time is calculated by the product of potential difference, current and time consumed and it is solved as 918.75mJ.
The amount of energy used by the portable CD player can be calculated using the formula:
E = VIt
where E is the energy, V is the potential difference, I is the current and t is the time.
The portable CD player uses a current of 7.5 mA at a potential difference of 3.5 V.
Thus, the energy used by the player in 35 seconds can be calculated as follows:
[tex]E = VIt\\ = 3.5 V \times 7.5 mA \times35 s \\= 918.75 mJ[/tex]
Therefore, the portable CD player uses 918.75 mJ of energy in 35 seconds.
For further details on potential difference, click on the below link:
https://brainly.com/question/12918923
#SPJ11
2. how would an atmosphere of helium effect the pitch of an organ pipe? how would it effect the pitch of a turning fork? explain. g
An atmosphere of helium would have a large effect on the pitch of instruments. For an organ pipe, helium would cause the pitch of the instrument's sound to be higher than normal.
This is because helium is a lighter gas than air, and therefore has a higher speed of sound through it. This increases the frequency of the sound waves, resulting in a higher pitch. For a tuning fork, helium would also cause the pitch of the sound to be higher than normal, however, the effect would be less significant.
This is because the frequency of the sound waves produced by a tuning fork is determined more by the size and shape of the fork, rather than the gas that it is in. Therefore, while the pitch of a tuning fork would be higher in a helium atmosphere, the effect would not be as great as with an organ pipe.
Know more about helium here
https://brainly.com/question/4945478#
#SPJ11
how are thew avelength, freequency, and speed of a wave realted? how do they depend on the medium through which the wave is passing and the type of wave
Wavelength, frequency, and speed of wave are related by the following formula:v = fλ
where v is the speed of the wave, f is the frequency of the wave, and λ is the wavelength of the wave.
In terms of the medium through which the wave is passing, the speed of the wave depends on the properties of the medium. The speed of a wave traveling through a medium depends on the medium's elasticity and density. The type of wave, such as sound or light, will also determine the speed of the wave.In terms of wavelength and frequency, they are inversely proportional. This means that if the wavelength increases, the frequency decreases, and if the wavelength decreases, the frequency increases. This is expressed by the formula:f = v/λSo, as the speed of the wave increases, the wavelength increases, and the frequency decreases. Conversely, as the speed of the wave decreases, the wavelength decreases, and the frequency increases.
To learn more about wavelength of wave https://brainly.com/question/21986654
#SPJ11
what is the maximum speed with which a 1500 kg car can make a turn around a curve of a radius 20 m. on a level. road without sliding.
The maximum speed with which a 1500 kg car can make a turn around a curve of a radius 20 m. on a level road without sliding is approximately 0.823 m/s.
The maximum speed with which a 1500 kg car can make a turn around a curve of a radius 20 m. on a level road without sliding is determined by the maximum static friction force, Fsmax, that can be created between the car tires and the road surface. The formula for the static friction force is Fsmax = μsFn, where μs is the coefficient of static friction and Fn is the normal force acting on the car. The normal force can be calculated using Newton's Second Law, Fn = mv2/r, where m is the mass of the car, v is the speed, and r is the radius of the curve.
Therefore, the maximum speed with which the car can make the turn without sliding can be calculated as follows:
v2 = (μsm2)/(rFn) = (μs15002)/(20 * 1500 * 9.8) = 0.68 m/s2
v = √(0.68 m/s2) = 0.823 m/s
For more such questions on speed
https://brainly.com/question/13943409
#SPJ11
a sports car crosses the bottom of a valley with a radius of curvature equal to 95 m. at the very bottom, the normal force on the driver is twice his weight. at what speed was the car traveling?
The car was traveling at a speed of 54.6 m/s (approximately 196.6 km/h) at the bottom of the valley.
The normal force on the driver is equal to the weight of the driver plus the weight of the car, which is twice the weight of the driver. This means that the total weight on the car is three times the weight of the driver.
Therefore, the centripetal force acting on the car is equal to three times the weight of the driver, which is equal to mv^2/r, where m is the mass of the car, v is the velocity of the car, and r is the radius of curvature.
Solving for v, we get v = √(3gr), where g is the acceleration due to gravity. Substituting the given values, we get v = √(3 x 9.81 x 95) = 54.6 m/s.
Therefore, the car was traveling at a speed of 54.6 m/s (approximately 196.6 km/h) at the bottom of the valley.
For more questions like Speed click the link below:
https://brainly.com/question/28224010
#SPJ11
suppose you have an atwood machine with two different masses m and m. what are the external forces acting on this system?
The external forces acting on this system are: gravity and the tension in the string.
An Atwood machine is a system consisting of two masses, m, and m, connected by a string that passes over a pulley. In this system, the external forces are gravity and the tension in the string. Gravity pulls both masses downward, while the tension in the string acts in opposite directions on the two masses, pulling the heavier one down and the lighter one up.
The tension in the string is determined by the masses m and m and the acceleration of the system. If m is the heavier mass and m is the lighter mass, the tension in the string will be greater than if both masses had the same weight. This is because the tension must balance the gravitational forces on the two masses. The greater the mass, the greater the gravitational force, and the greater the tension in the string must be to balance it.
The acceleration of the system is determined by the masses, the tension in the string, and the amount of friction in the system. The greater the tension, the greater the acceleration, and the smaller the mass, the greater the acceleration. Friction acts against the acceleration, reducing the net acceleration of the system.
In summary, the external forces acting on an Atwood machine with two different masses m and m are gravity and the tension in the string. The tension in the string is determined by the masses and the acceleration of the system, while the acceleration is determined by the masses, the tension in the string, and the amount of friction in the system.
To know more about gravity refer here:
https://brainly.com/question/14874038#
#SPJ11
a skydiver is descending towards the earth with her parachute open. the work done by the drag force from the air is
When a skydiver descends towards the earth with her parachute open, the work done by the drag force from the air is negative.
When a skydiver descends towards the earth with her parachute open, the drag force works in the opposite direction of the skydiver's motion, slowing her descent. The skydiver's motion is downward, whereas the drag force is upward. As a result, the angle between the drag force and the skydiver's motion is 180 degrees.
Because of the dot product, the work done by the drag force is negative.Work, which is a scalar quantity, is given by the following equation:
Work done = Force * Displacement * cos(θ)
where: θ is the angle between the applied force and the displacement vector. The work done is negative in this case because the angle between the applied force and the displacement is 180 degrees.
As a result, cos(180) is -1. This negative value results in the work done by the drag force from the air being negative.
To know more about drag force refer here:
https://brainly.com/question/12774964#
#SPJ11
g what is the expected acceleration of the cart if its mass is 220 g and two masses of 250 g each are added to it. a mass of 60 g is placed in the mass hanger of 5 g.
The expected acceleration of the cart when two masses of 250 g are added to it, and a mass of 60 g is placed in the mass hanger of 5 g, given that its mass is 220 g is 1.55 m/s².
What is acceleration?
Acceleration is the change in velocity with respect to time. It can be defined as the rate at which the velocity of a body changes with respect to time. It is denoted by "a".
Mass is the amount of matter in a body or object. It is a scalar quantity, which is denoted by "m".
acceleration: a = (v - u) / t
Where; a = acceleration
v = final velocity
u = initial velocity
t = time taken
The expected acceleration of the cart:
Mass = Mass of cart + Mass of 2 masses
Mass = 220 g + (2 × 250 g)
Mass = 720 g
The total mass hanging on the mass hanger:
Mass on hanger = Mass of hanger + Mass on a hanger
Mass on hanger = 5 g + 60 g
Mass on hanger = 65 g
The net force acting on the system.
Net force = (Mass on hanger + Mass) × gNet force
= (65 g + 720 g) × 9.8 m/s²
Net force = 7.06 N
The expected acceleration of the cart;
a = F / ma
= (7.06 N) / (720 g)
a = (7.06 N) / (0.72 kg)a
= 9.81 m/s² × (7.06 / 0.72)a
= 1.55 m/s²
Therefore, the expected acceleration of the cart when two masses of 250 g are added to it, and a mass of 60 g is placed in the mass hanger of 5 g, given that its mass is 220 g is 1.55 m/s².
To know more about velocity:
https://brainly.com/question/29519833
#SPJ11
what is the direction of the magnetic force acting on the wire in part b due to the applied magnetic field?
The direction of the magnetic force acting on the wire in part b due to the applied magnetic field is: downward, or towards the ground.
This is because the magnetic field, which is produced by the current flowing through the wire, is always oriented in a circle around the wire. Therefore, the magnetic force is also oriented in a circle, with the downward direction pointing towards the ground.
To understand this further, consider the right-hand rule, which states that if you wrap your right hand around the wire, then your thumb will point in the direction of the magnetic force.
To sum up, the direction of the magnetic force acting on the wire in part b due to the applied magnetic field is downward, or towards the ground. This can be understood by considering the right-hand rule, which states that if you wrap your right hand around the wire, then your thumb will point in the direction of the magnetic force.
To know more about magnetic fields refer here:
https://brainly.com/question/23096032#
#SPJ11
How is the blue color of a reflection nebula related to the blue color of the daytime sky?
Reflection nebulae look blue for the same reason the sky looks blue. Short wavelengths scatter more easily than long wavelengths.
The blue color of a reflection nebula is related to the blue color of the daytime sky because both phenomena are caused by the scattering of light.
In the case of the daytime sky, the blue color is due to the scattering of sunlight by the Earth's atmosphere, which causes blue light to be scattered more than other colors, making it the dominant color in the sky. In a reflection nebula, the blue color is also caused by the scattering of light, but this time it is by dust grains in the nebula reflecting light from nearby stars.
The dust grains scatter blue light more effectively than other colors, which gives the nebula its characteristic blue color. Therefore, both the blue color of the sky and the blue color of a reflection nebula are a result of the scattering of light by particles in their respective environments.
To know more about nebula, here
brainly.com/question/9497068
#SPJ4
--The complete question is, How is the blue color of a reflection nebula related to the blue color of the daytime sky?--