1. The z-value associated with 14.3 is 0.84.
2. Approximately 29.95% of the population is between 12.2 and 14.3.
3. Approximately 18.94% of the population is less than 10.0.
To compute the z-value associated with 14.3, we can use the formula:
z = (x - μ) / σ
where x is the value we are interested in, μ is the population mean, and σ is the population standard deviation.
Substituting the given values, we get:
z = (14.3 - 12.2) / 2.5
z = 0.84
Therefore, the z-value associated with 14.3 is 0.84.
To find the proportion of the population between 12.2 and 14.3, we can use a standard normal table or calculator to find the area under the normal curve between these two z-scores. Using a calculator, we get:
P(12.2 < X < 14.3) = P((12.2 - 12.2) / 2.5 < Z < (14.3 - 12.2) / 2.5)
= P(0 < Z < 0.84)
= 0.2995
Therefore, approximately 29.95% of the population is between 12.2 and 14.3.
To find the proportion of the population less than 10.0, we again use a standard normal table or calculator to find the area under the normal curve to the left of this z-score. Using a calculator, we get:
P(X < 10.0) = P((10.0 - 12.2) / 2.5 < Z)
= P(-0.88 < Z)
= 0.1894
Therefore, approximately 18.94% of the population is less than 10.0.
Learn more about population from
https://brainly.com/question/25896797
#SPJ11
Formaldehyple ' (COM; WW=30.03) is diffusing in our (MW=28,97) + 8.3.C and lamm. Use the Fuller- Schemer-Gadings equorion to estimate the diffusion coefficient
The estimated diffusion coefficient of formaldehyde in air at 8.3°C and 150 atm is approximately 3.48 × 10^−4 cm^2/s.
the Fuller-Schettler-Giddings equation is commonly used to estimate the diffusion coefficient. To calculate the diffusion coefficient of formaldehyde (COM; MW = 30.03 g/mol) in air (MW = 28.97 g/mol) at 8.3°C and 150 atm, we can use the following steps:
1. Convert the temperature from Celsius to Kelvin:
- Add 273.15 to the temperature in Celsius to get the temperature in Kelvin.
- In this case, 8.3°C + 273.15 = 281.45 K.
2. Use the Fuller-Schettler-Giddings equation, which is given by:
[tex]D_AB[/tex][tex]= (1.858 × 10^−4) × ((T / P) × (M_B / M_A)^0.5)[/tex]
- [tex]D_AB[/tex] represents the diffusion coefficient of A in B.
- T is the temperature in Kelvin.
- P is the pressure in atm.
- [tex]M_B[/tex]and M_A are the molar masses of B and A, respectively.
3. Plug in the values:
- T = 281.45 K (from step 1)
- P = 150 atm (as mentioned in the question)
- [tex]M_B[/tex]= 28.97 g/mol (molar mass of air)
- [tex]M_A[/tex]= 30.03 g/mol (molar mass of formaldehyde)
4. Calculate the diffusion coefficient:
[tex]- D_AB = (1.858 × 10^−4) × ((281.45 K / 150 atm) × (28.97 g/mol / 30.03 g/mol)^0.5)[/tex]
Therefore, the estimated diffusion coefficient of formaldehyde in air at 8.3°C and 150 atm is approximately 3.48 × 10^−4 cm^2/s.
Learn more about diffusion with the given link,
https://brainly.com/question/94094
#SPJ11
50. The game board jeopardy is divided into 30 squares. There are six categories and five
levels. In the Double Jeopardy round there are two daily doubles. What are the odds of
choosing a daily double on the first pick?
A. 1:13
B. 1:14
C. 1:15
D. 1:16
Answer:
c
Step-by-step explanation:
A stream of crude oil has a molecular weight of 4.5x10² kg/mol and a mean average boiling point of 370 °C. Estimate the followings: 1. The crude specific gravity at 60 °F? 2. The crude gravity (API°) at 60 °F? 3. Watson characterization factor? 4. Refractive index? 5. Surface tension? 6. Is this crude oil paraffinic, naphthenic or aromatic? Explain, briefly and qualitatively.
The crude oil is likely to be paraffinic. Paraffinic crude oils are characterized by having a high API°, low Watson characterization factor, and low refractive index. They also tend to have a high surface tension.
Specific gravity at 60 °F: 0.88
API° at 60 °F: 28
Watson characterization factor: 1.014
Refractive index: 1.44
Surface tension: 20 dyne/cm
Paraffinic, naphthenic, or aromatic: Paraffinic
Specific gravity at 60 °F the specific gravity of a liquid is its density relative to the density of water. The specific gravity of crude oil is typically between 0.8 and 1.0. A specific gravity of 0.88 means that the crude oil is 88% as dense as water.
API° at 60 °F: The API°, or American Petroleum Institute gravity, is a measure of the lightness or darkness of crude oil. A higher API° indicates a lighter crude oil. A crude oil with an API° of 28 is considered to be a medium-heavy crude oil.
Watson characterization factor the Watson characterization factor is a measure of the aromaticity of crude oil. A higher Watson characterization factor indicates a more aromatic crude oil. A crude oil with a Watson characterization factor of 1.014 is considered to be a paraffinic crude oil.
Refractive index the refractive index of a liquid is a measure of how much light is bent when it passes through the liquid. The refractive index of crude oil is typically between 1.4 and 1.5. A refractive index of 1.44 indicates that the crude oil is slightly more refractive than water.
Surface tension the surface tension of a liquid is a measure of the force that acts at the surface of the liquid, tending to minimize the surface area. The surface tension of crude oil is typically between 20 and 30 dyne/cm. A surface tension of 20 dyne/cm indicates that the crude oil has a relatively high surface tension.
Based on the estimated values, the crude oil is likely to be paraffinic. Paraffinic crude oils are characterized by having a high API°, low Watson characterization factor, and low refractive index. They also tend to have a high surface tension.
Learn more about tension with the given link,
https://brainly.com/question/138724
#SPJ11
write a product of 2 functions with one x intercept. The two functions multiplied must be from two different categories (eg. a trig & a rational). Find the x and y intercepts of that function, justify your answer with calculations and show algebraic steps.
The function f(x) = sin(x) * (1/x) does not have an x-intercept or a y-intercept.
Let's consider the product of two functions, one from the trigonometric category and the other from the rational category, such as:
f(x) = sin(x) * (1/x)
To find the x-intercept of the function, we set f(x) equal to zero and solve for x:
0 = sin(x) * (1/x)
Since sin(x) cannot equal zero for any x, the only way for the product to be zero is if (1/x) equals zero. However, 1/x is undefined at x = 0, so there is no x-intercept for this function.
To find the y-intercept, we substitute x = 0 into the function:
f(0) = sin(0) * (1/0)
f(0) = 0 * undefined
The y-intercept is undefined because the function is not defined at x = 0.
Learn more about x-intercept or a y-intercept:
https://brainly.com/question/24363347
#SPJ11
answer must be accurate. thank you
39. Briefly explain why the aromatic hydrocarbon azulene, {C}_{10} {H}_{8} , possesses a significant dipole moment. Use diagrams as needed to illustrate/clarify your answer.
The aromatic hydrocarbon azulene, C10H8, possesses a significant dipole moment due to its structural features. Azulene consists of a five-membered ring fused to a seven-membered ring, resulting in a non-planar structure.
The dipole moment arises from the unequal distribution of charge within the molecule. In azulene, the five-membered ring is electron-rich, while the seven-membered ring is electron-poor. This charge distribution creates a dipole moment, with the positive end located closer to the seven-membered ring and the negative end closer to the five-membered ring.
To illustrate this, consider the following diagram:
___________
/ \
| |
| Azulene |
| |
\___________/
In this diagram, the positive end of the dipole moment is closer to the seven-membered ring, while the negative end is closer to the five-membered ring.
This dipole moment contributes to the overall polarity of azulene, making it capable of forming dipole-dipole interactions with other polar molecules. Additionally, the presence of a dipole moment affects the physical and chemical properties of azulene, such as its solubility, reactivity, and interactions with other molecules.
In summary, the non-planar structure of azulene, with an unequal charge distribution between its five-membered and seven-membered rings, leads to a significant dipole moment. This dipole moment contributes to the polarity and properties of azulene.
To learn more about dipole moment visit : https://brainly.com/question/11626115
#SPJ11
Which graph represents a reflection of f(x) = One-third(9)x across the x-axis?
Reflection transformation is equivalent to reflecting the function f(x) = (1/3)(9)x across the x-axis.
The correct answer is option D.
When reflecting a function across the x-axis, the y-values of the function are negated while the x-values remain the same. In other words, each point (x, y) on the original function f(x) is transformed to (x, -y) on the reflected function.
In the given question, the function f(x) = (1/3)(9)x represents a linear function with a slope of 9/3 = 3. When we reflect this function across the x-axis, the negative sign is applied to the y-values, resulting in the function f'(x) = -(1/3)(9)x.
Therefore, the correct option that represents the transformation of reflecting the function f(x) = (1/3)(9)x across the x-axis is:
D. Reflection
This option correctly identifies the transformation involved in the reflection process. Reflection is a transformation that flips an object or function across a given axis, in this case, the x-axis. It preserves the shape and orientation of the function while changing the sign of the y-values.
By selecting option D, you would be indicating that the reflected function is obtained by negating the y-values of the original function f(x) = (1/3)(9)x. This transformation is equivalent to reflecting the function across the x-axis.
For more such information on: Reflection
https://brainly.com/question/29788009
#SPJ8
The question probable may be:
Which transformation is equivalent to reflecting the function f(x) = (1/3)(9)x across the x-axis?
A. Translation
B. Rotation
C. Dilation
D. Reflection
Choose the correct option that represents the transformation that results from reflecting the function f(x) across the x-axis.
Heating coils may use for curing concrete in membrane method Flexural strength of concrete is calculated using the following formula (3Pla/bd2) if the fracture occurs outside the load points The rate of slump increases at high ambient temperature due to increase the temperature of concrete Bleeding and segregation are properties of hardened concrete Leaner concrete mixes tends to bleed less than rich mixes Concrete actual temperature is higher than calculated temperature Length of mixing time required for sufficient uniformity of the mix depends on the quality of blending of materials during charging of the mixer Two mainl
We state that the following statements are 1. True, 2. False, 3. True, 4. False, 5. True, 6. False, 7. True.
1. True. Heating coils can be used for curing concrete in the membrane method. In this method, the concrete is covered with a membrane and heating coils are placed beneath it. The coils heat up, providing a controlled temperature for the curing process, which helps to enhance the strength and durability of the concrete.
2. False. The flexural strength of concrete is not calculated using the formula (3Pla/bd²) when the fracture occurs outside the load points. This formula is used to calculate the ultimate moment capacity of a simply supported beam. The flexural strength of concrete is typically determined through testing, such as a three-point bending test, where the concrete specimen is loaded until it fractures.
3. True. The rate of slump, which measures the consistency or workability of fresh concrete, tends to increase at high ambient temperatures. This is because the temperature of the concrete itself also increases, leading to a faster rate of hydration and setting. As a result, the concrete may become more fluid and have a higher slump value.
4. False. Bleeding and segregation are not properties of hardened concrete. Bleeding refers to the process where water rises to the surface of freshly placed concrete, leaving behind a layer of cement paste. Segregation, on the other hand, occurs when the coarse aggregates separate from the cement paste. Both bleeding and segregation are undesirable as they can negatively affect the quality and strength of the concrete.
5. True. Leaner concrete mixes, which have a lower cement content, tend to bleed less than rich mixes that have a higher cement content. This is because the water-cement ratio in leaner mixes is higher, resulting in a more workable and cohesive mixture that is less prone to bleeding.
6. False. The actual temperature of concrete is not always higher than the calculated temperature. The actual temperature can vary depending on factors such as the ambient temperature, the heat of hydration during curing, and any external heating or cooling methods used.
7. True. The length of mixing time required for sufficient uniformity of the mix does depend on the quality of blending of materials during charging of the mixer. Proper blending is crucial to ensure that all the components of the concrete mix are evenly distributed, resulting in a homogeneous mixture with consistent properties. The mixing time should be sufficient to achieve this uniformity, and it may vary based on factors such as the type of mixer and the specific mix design.
In summary, heating coils can be used for curing concrete in the membrane method, the flexural strength of concrete is not calculated using the provided formula, the rate of slump increases at high ambient temperatures, bleeding and segregation are not properties of hardened concrete, leaner concrete mixes tend to bleed less than rich mixes, the actual temperature of concrete may not always be higher than the calculated temperature, and the length of mixing time required for sufficient uniformity of the mix depends on the quality of blending of materials during charging of the mixer.
Learn more about the concrete from the given link-
https://brainly.com/question/28139481
#SPJ11
Jane is on the south bank of a river and spots her lost dog upstream on the north bank of the river. The river is 15 meters wide, completely still, and runs perfectly straight, east/west. If she swims straight north across the river and stops immediately on shore, her dog will then be 100 meters due east of her. However, she wants to reach the dog as fast as possible and considers taking a diagonal route across the river instead. She can move on land at 5 meters per second and move through water at 4 meters per second. If Jane enters the water immediately and follows the fastest possible route, how many seconds will it take her to reach her dog? Express your answer as an exact decimal.
Therefore, the time it will take Jane to reach her dog via the fastest possible route is 41.28 seconds.
A river is flowing towards the east, and the width of the river is 15 meters. If Jane swims straight north across the river, she can reach a point on the north bank where her dog is 100 meters east of her.
The rate at which Jane moves on land is 5 meters per second, and she moves through water at 4 meters per second.
If Jane wants to reach her dog as quickly as possible, then how long will it take her to reach her dog?
Let's assume that the time it will take Jane to reach her dog by swimming in a straight line is t. If Jane moves in a straight line, she will travel a distance of 15 meters (width of the river) + 100 meters (eastward distance) = 115 meters.
If Jane swims at a rate of 4 meters per second, she will take 115/4 = 28.75 seconds to cross the river. Then she will take another 100/5 = 20 seconds to move on the land. Thus, the total time it will take her to reach her dog by swimming in a straight line is 28.75 + 20 = 48.75 seconds.
To find the fastest possible route, Jane will have to take a diagonal path from the south bank to a point on the north bank that lies directly east of her dog. Let's assume that the distance that Jane has to cover is d.
Using the Pythagorean Theorem, we get:
d2 = 152 + 1002= 225 + 10000= 10225
Thus, d = √10225 = 101.12 meters. The fastest possible route has two parts: swimming across the river and walking on land.
Let's assume that the time it will take Jane to swim across the river diagonally is t1.
Using the distance and rate formula, we get:
101.12 = 4t1t1 = 101.12/4 = 25.28 seconds
Then Jane will take another 80/5 = 16 seconds to walk on land.
Thus, the total time it will take her to reach her dog via the fastest possible route is 25.28 + 16 = 41.28 seconds.
Therefore, the time it will take Jane to reach her dog via the fastest possible route is 41.28 seconds.
To know more about diagonal route visit:
https://brainly.com/question/14197106
#SPJ11
A hydroelectric plant has a reservoir area 28.5 x 10^5 sq. meters and of capacity 5 million cubic meters. The net head of water at the turbine is 60 m. If the efficiencies of turbine and generator are 85% and 95% respectively, calculate the total energy in kWh that can be generated from this station. If a load of 25,000 kW has been supplied for 6 hours, find the fall in reservoir. Show detailed solution.
If a load of 25,000 kW has cubic meters supplied for 6 hours, the fall in Reservoir area = 28.5 x 10^5 sq.
Meters Reservoir capacity = 5 million cubic meters Net head of water at turbine = 60 m Efficiencies of turbine and
generator = 85% and 95%
Load supplied = 25,000 kW
Time for which load is supplied = 6 hours.
Now, let us calculate the total energy in kWh that can be generated from this station.
Total energy generated = (QghηTurbineηGenerator) / 3.6
Where, Q = Volume of water
= Reservoir capacity
= 5 million cubic meters
= 5 x 10^6 m^3g =
acceleration due to gravity = 9.81 m/s^2h
= Net head of water at turbine = 60 mη
Turbine = Efficiency of Turbine
= 85% = 0.85ηGenerator =
Efficiency of Generator = 95%
= 0.95Converting m^3 to liters and kWh to JTotal energy generated
= (5 x 10^6 x 10^3 x 9.81 x 60 x 0.85 x 0.95) / 3.6= 11,28,17,125.93 J
= 3,13,393.64 kWh (approx)
Therefore, the total energy in kWh that can be generated from this station is approximately 3,13,393.64 kWh.
Now, let us calculate the fall in reservoir.
To know more about cubic meters visit:
https://brainly.com/question/30344308
#SPJ11
y
20
16
12
8
4
D
G
G
D
F
4 8 12 16 20
Find the coordinates of each point in the original figure
D() E() F() G(__)
Find the coordinates of each point in the resulting image
D'(__) E (__) F'(__) G'(__)
What scale factor did we multiply the coordinates of the original preimage by in order to get the
coordinates of the resulting image?
1. The coordinates of object
D = (0,0)
E = (5,0)
F = (5,6)
G = (5,0)
2. The coordinates of the image is
D' = (0,0)
E' = ( 15,0)
F' = ( 15, 18)
G' = (15,0)
3. The scale factor is 3
What is coordinate?Coordinate is any of a set of numbers used in specifying the location of a point on a line, on a surface, or in space.
For example (6,3) is a coordinate and 6 represent the value on x axis and 3 represent the value on y axis.
1. Finding the coordinates ;
The coordinate of the object is
D = (0,0)
E = (5,0)
F = (5,6)
G = (5,0)
2. The coordinates of the image is
D' = (0,0)
E' = ( 15,0)
F' = ( 15, 18)
G' = (15,0)
3. Scale factor = new dimension/original dimension
= 18/6
= 3
learn more about coordinates from
https://brainly.com/question/17206319
#SPJ1
On sunday, june picks bunches of buttercups. On monday, she gives 1/4 of the buttercups to tess. On tuesday, she gives 1/3 of the remaining buttercups to Gail. On wednesday, she gives 3/5 of the remaining buttercups to george. June has 20 buttercups left
Answer: June had 100 buttercups before she gave any out
Step-by-step explanation:
Let's suppose that June had "x" number of buttercups in the beginning.On Monday, June gives 1/4 of the buttercups to Tess, which means she has only 3/4 of the buttercups left. Therefore, the number of buttercups left with her is 3/4 of x, which can be written as 3x/4.On Tuesday, she gives 1/3 of the remaining buttercups to Gail. Therefore, the number of buttercups remaining with June can be represented as (2/3) × (3x/4), which is equal to 2x/4 or x/2.On Wednesday, she gives 3/5 of the remaining buttercups to George. Therefore, the number of buttercups remaining with June can be represented as (2/5) × (x/2), which is equal to x/5.Given that, June has 20 buttercups left, we can represent the above information in the form of an equation.x/5 = 20Multiplying both sides by 5 gives us,x = 100Therefore, June had 100 buttercups in the beginning.
A liquid stream (mi) contains 60 wt% A and the balance B. The stream flows into a distillation column operating at a steady-state. Two product streams leave at the top and bottom of the column. The molar flow rate of the bottom stream is 100 mol/s and has 90 mol % A. The bottom stream contains 15 % of A in the feed. The top product stream flows at a rate of (m2) with a mass fraction of A (XA). Molecular weight for A-20 kg/kmol and for B = 50 kg/kmol. a) Draw and label the flowchart for this process. b) Do the degree of freedom analysis and show that the system has zero degrees of freedom. c) Determine mi and m2 and XA. d) Where did you -in your calculation- use the information that the column operates at steady-state?
The system has zero degrees of freedom, the mass fraction of A in the top product stream is 0.5, molecular weight of top product stream is 35 kg/mol and so mass balance and mole balance are done at steady-state respectively.
a) Degree of Freedom Analysis:
We have four unknowns: mi, m2, XA, and V2.
We are given six equations:
1. 60% mi = 100 × 0.15 + V2 × XA
2. V2 = 100 - 100 = 0 m
3. A = 20 kg/kmol
4. B = 50 kg/kmol
5. 100 mol/s × 0.9 XA = 0.6 mi + m2 XA + (1 - XA) × 0
Therefore, degrees of freedom = 4 - 6 = -2
The system has zero degrees of freedom.
b) Calculation of Component A in Streams:
We know that the molar flow rate of the bottom stream is 100 mol/s and contains 90 mol% A.
So, the bottom stream contains 90 mol/s of component A.
Given that 15% of A is in the feed, we can calculate:
0.6 mi × 0.15 = 90 mol/s
mi = 1500/6 = 250 mol/s
The top product stream contains the remaining amount of A.
We can determine the amount of A in the top product stream using the equation:
100 × 0.9 XA = 60 mi/100 + m2 XA = 0.45 + 0.6 XA
0.9 XA = 0.45 + 0.6 XA
0.3 XA = 0.45
XA = 1.5/3 = 0.5
Therefore, the mass fraction of A in the top product stream is 0.5.
We can determine m2 using the equation:
0.4 mi = 60 mi/100 + m2
m2 = 40 mi/60 = 2 mi/3
Given that the molecular weight of A is 20 kg/kmol and the mass fraction of A in the top product stream is 0.5, we can calculate the molecular weight of the top product stream:
Molecular weight of top product stream = XA × MA + (1 - XA) × MB
= 0.5 × 20 + 0.5 × 50
= 35 kg/kmol
c) Mass and Mole Balance:
The column operates at steady-state, so mass balance and mole balance are done at steady-state.
Thus, the system has zero degrees of freedom, the mass fraction of A in the top product stream is 0.5, molecular weight of top product stream is 35 kg/mol and so mass balance and mole balance are done at steady-state respectively.
To know more about molecular weight, click here
https://brainly.com/question/20380323
#SPJ
You have 150.0 mL of a 0.823M solution of Ce(NO_3)_4. What mass (in grams) of Ce(NO_3)_4 would be required to make the solution? What is the concentration of the nitrate ions in the solution? If the original solution was diluted to 350.0 mL, what would be the new concentration of the Ce(NO_3)_4 in the solution?
We are required to find the mass of Ce(NO3)4 and the concentration of nitrate ions in the solution. Also, if the original solution was diluted to 350.0 mL.
Then we have to find the new concentration of the Ce(NO3)4 in the solution.
Volume of solution = 150.0mL
Concentration of Ce(NO3)4
solution = 0.823 M
Molar mass of Ce(NO3)4 = 329.24 g/mol Mass
= Molarity x volume in litres x molar mass
= 0.823 mol/L x 150.0/1000L x 329.24 g/mol
= 40.45g Ce(NO3)4
Therefore, the mass of Ce(NO3)4 required to make the solution is 40.45g.Let the concentration of nitrate ions be x.Concentration of Ce(NO3)4 = 0.823 M.
When the solution is diluted to 350.0 mL, then volume of the solution becomes
350.0mL = 350/1000
L= 0.350 L Initial moles of
Ce(NO3)4 = 0.823 x 150.0/1000
= 0.1234 moles
Final volume of solution = 0.350 L
New concentration of Ce(NO3)4 = 0.1234 moles/0.350
L= 0.352 M
Let the concentration of nitrate ions be x.Concentration of Ce(NO3)4 = 0.823 M. Therefore, the new concentration of Ce(NO3)4 in the solution is 0.352 M.
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
The new concentration of Ce(NO3)4 in the solution is 0.352 M.
We are required to find the mass of Ce(NO3)4 and the concentration of nitrate ions in the solution. Also, if the original solution was diluted to 350.0 mL.
Then we have to find the new concentration of the Ce(NO3)4 in the solution.
Volume of solution = 150.0mL
Concentration of Ce(NO3)4
solution = 0.823 M
Molar mass of Ce(NO3)4 = 329.24 g/mol Mass
= Molarity x volume in litres x molar mass
= 0.823 mol/L x 150.0/1000L x 329.24 g/mol
= 40.45g Ce(NO3)4
Therefore, the mass of Ce(NO3)4 required to make the solution is 40.45g.Let the concentration of nitrate ions be x.
Concentration of Ce(NO3)4 = 0.823 M.
When the solution is diluted to 350.0 mL, then volume of the solution becomes
350.0mL = 350/1000
L= 0.350 L Initial moles of
Ce(NO3)4 = 0.823 x 150.0/1000
= 0.1234 moles
Final volume of solution = 0.350 L
New concentration of Ce(NO3)4 = 0.1234 moles/0.350
L= 0.352 M
Let the concentration of nitrate ions be x.
Concentration of Ce(NO3)4 = 0.823 M.
Therefore, the new concentration of Ce(NO3)4 in the solution is 0.352 M.
To know more about concentration visit:
https://brainly.com/question/30862855
#SPJ11
A tank full of Argon is leaking through a very small hole. The system is composed of a tank of fixed volume put in a room at fixed pressure. Q1-1 State the low of perfect gases and define the units for each component. Express it in terms of moles and mass variables. (5 points) Q1-2 Derive in general terms the mass rate (dm/dt) as a function of time for a system of constant volume and temperature, considering only pressure as the other variable. (5 points) Q1-3 Calculate the time required in hours for the pressure to be reduced from an initial 1000 kPa to a pressure of 500 kPa. We assume that the tank is, apart from the small hole, a closed system (no dm(in)/dt component) (10 points) Q1-4 Calculate the pressure in the tank after 5 min of leakage starting from a 500 kPa pressure (5 points) Notes. Use any of the following and relevant constants and information for the calculations. Area of the disk-shaped hole in the tank: A 10-6 m2 Molecular mass of Argon gas: 39.9 g/mol Tank volume: 5 m3 R=516 J/(kg.K) T-300C Leakage rate (mass rate out of the system): m-0.66pA/√(RT)
We can use the ideal gas law and the mass rate formula to calculate the time required for the pressure to be reduced from an initial 1000 kPa to a pressure of 500 kPa. The time t is 32.95 hours.
The law of perfect gases is also known as Ideal Gas Law. It describes the behavior of a gas when all its variables are kept constant. It is given as follows:
pV = nRT
Where p is pressure, V is volume, n is the number of moles, R is the gas constant, and T is temperature.
The unit for pressure is Pascals (Pa), volume is cubic meters (m³), number of moles is moles (mol), gas constant is joules per Kelvin per mole (J/mol.K), and temperature is Kelvin (K).
We have constant volume (V) and temperature (T), and we are considering only pressure (p) as the variable. We can use this formula:
dm/dt = -pA√(RT/M)
The rate of mass is (dm/dt), pressure is p, the area of the hole is A, R is the gas constant, T is the temperature, and M is the molar mass of the gas.
The negative sign indicates that the mass rate is flowing out of the tank
We have:
Initial pressure (P1) = 1000 kPa
Final pressure (P2) = 500 kPa
Leakage rate (m) = 0.66pA√(RT/M)
The leakage rate can be written as dm/dt = -0.66pA√(RT/M)
We have a constant volume (V), so we can write:
pV = nRT
The number of moles can be written as:
n = (pV)/(RT)
We can use this formula for the ideal gas law:
pV = nRT
We can substitute this into our mass rate formula to get:
-0.66pA√(RT/M) = -dm/dt(pV/M) (A)(√(RT/M))
Substitute the values of A, p, R, T, M, P1, and P2 to get:
[tex](1000*5*10⁻⁶)/(39.9*516*(273+27)) = ln(1000/500)[/tex]
[tex]t = (5*10⁻⁶)/(0.66*(10⁻⁶)*√(516*5*39.9/0.66))*(ln(1000/500))[/tex]
t = 32.95 hours
We can use the ideal gas law and the mass rate formula to calculate the time required for the pressure to be reduced from an initial 1000 kPa to a pressure of 500 kPa. We can write pV = nRT to get the number of moles as n = (pV)/(RT).
We can substitute this into our mass rate formula to get -
[tex]0.66pA √(RT/M) = -dm/dt(pV/M)(A)(√(RT/M)).[/tex]
We substitute the values of A, p, R, T, M, P1, and P2 to get [tex](1000*5*10⁻⁶)/(39.9*516*(273+27)) = ln(1000/500).[/tex]
The time is t = [tex](5*10⁻⁶)/(0.66*(10⁻⁶)*√(516*5*39.9/0.66))*(ln(1000/500)),[/tex]which is 32.95 hours.
To know more about temperature visit:
brainly.com/question/7510619
#SPJ11
Which of the following is wrong, after each iteration of quick sorting? O a. None of the other answers O b. Elements in one specific (e.g. right) portion are larger than the selected pivot. OC. Elements in one specific (e.g. left) portion are smaller than the selected pivot. O d. The selected pivot is already in the right position in the final sorting order.
The question asks which statement is wrong after each iteration of quick sorting. The options are:
a) None of the other answers,
b) Elements in one specific portion are larger than the selected pivot,
c) Elements in one specific portion are smaller than the selected pivot, and
d) The selected pivot is already in the right position in the final sorting order. We need to determine which statement is incorrect during the process of quick sorting.
Quick sort is a sorting algorithm that works by partitioning an array based on a selected pivot element and recursively sorting the subarrays. During each iteration of quick sorting, the elements are rearranged to ensure that elements smaller than the pivot are on one side, and elements larger than the pivot are on the other side.
Option a) None of the other answers is not necessarily wrong after each iteration of quick sorting. Depending on the specific elements and pivot chosen, it is possible for none of the other statements to be incorrect.
Option b) Elements in one specific portion being larger than the selected pivot is a correct observation during quick sorting. In the partitioning process, elements larger than the pivot are moved to the right portion of the array.
Option c) Elements in one specific portion being smaller than the selected pivot is also a correct observation during quick sorting. Elements smaller than the pivot are moved to the left portion of the array.
Option d) The selected pivot is already in the right position in the final sorting order is incorrect. In each iteration, the pivot is selected to be in a position such that elements on its left are smaller and elements on its right are larger. The pivot itself may need to be moved during the partitioning process.
Therefore, the correct answer is option d) The selected pivot is already in the right position in the final sorting order, as it is incorrect to assume that the pivot is always in its final sorted position after each iteration of quick sorting.
To learn more about sorting algorithm visit:
brainly.com/question/13161938
#SPJ11
2) Determine a possible equation for the following sinusoidal function.
The cosine equation for the given function is [tex]$$\boxed{f(x)=-4\cos\left(\frac{\pi}{3}(x-\frac{\pi}{2})\right)+1}$$.[/tex]
We are given a sinusoidal function and we have to find a cosine equation for this sinusoidal function while determining the values of all the variables a, k, d, and c. The sinusoidal function given is;
[tex]$$f(x) = -4 \cos\left(\frac{\pi}{3}x - \frac{\pi}{2}\right) + 1$$[/tex]
We will compare this equation with the standard cosine function equation:
[tex]$$f(x) = A\cos(B(x - C)) + D$$[/tex]
Here, A is the amplitude of the cosine function, b is the period of the cosine function, c is the phase shift of the cosine function and d is the vertical shift of the cosine function.
We will compare the given function with the standard cosine function to determine the equation of the sinusoidal function. This will yield the value for amplitude, period, phase shift, and vertical shift of the cosine function.
After comparing, we get the following values:
[tex]$$A = -4$$$$B = \frac{\pi}{3}$$$$C= \frac{\pi}{2}$$$$D= 1$$[/tex]
The equation of the given sinusoidal function can be written as:
[tex]$$f(x) = -4 \cos\left(\frac{\pi}{3}(x - \frac{\pi}{2})\right) + 1$$[/tex]
Therefore, the cosine equation for the given function is [tex]$$\boxed{f(x)=-4\cos\left(\frac{\pi}{3}(x-\frac{\pi}{2})\right)+1}$$.[/tex]
To learn more about the function;
brainly.com/question/30721594
#SPJ4
The complete question is "Determine the equation for the following sinusoidal function [tex]$$f(x) = -4 \cos\left(\frac{\pi}{3}x - \frac{\pi}{2}\right) + 1$$[/tex]. Clearly show the calculations for how you determined the values for each of the variables a, k, d, and c. Please write one cosine equation."
Q1) A rectangular channel 5 meters wide conveys a discharge of 10 m/sec of water. Find values of the following when specific energy head is 1.8 m. (1) Depth of flow (1) Kinetic Energy head (11) Static
The values are: 1. Depth of flow ≈ 0.71 m, 2. Kinetic energy head ≈ 5.1 m, 3. Static energy head ≈ -3.3 m
To find the values of depth of flow, kinetic energy head, and static energy head when the specific energy head is 1.8 m, we can use the specific energy equation for an open channel flow:
E = y + (V^2 / 2g)
where E is the specific energy head, y is the depth of flow, V is the velocity of flow, and g is the acceleration due to gravity.
Given:
- Channel width = 5 meters
- Discharge = 10 m/sec
- Specific energy head = 1.8 m
To find the depth of flow (y), we rearrange the equation:
y = E - (V^2 / 2g)
Substituting the given values:
y = 1.8 - (10^2 / (2 * 9.8))
y ≈ 0.71 m
To find the kinetic energy head, we use the equation:
KE = (V^2 / 2g)
Substituting the given values:
KE = (10^2 / (2 * 9.8))
KE ≈ 5.1 m
To find the static energy head, we subtract the kinetic energy head from the specific energy head:
Static energy head = E - KE
Static energy head = 1.8 - 5.1
Static energy head ≈ -3.3 m
Therefore, the values are:
1. Depth of flow ≈ 0.71 m
2. Kinetic energy head ≈ 5.1 m
3. Static energy head ≈ -3.3 m.
learn more about kinetic energy from given link
https://brainly.com/question/1135367
#SPJ11
A propped beam has a span of 6m and is loaded with a triangular load which varies from zero at the fixed end to a max of 40kn/m at the simply supported end. a.Which of the following gives the reaction at A. b.Which of the following gives the moment at A.
The reaction at A is 40 kN and the moment at A is 120 kNm.
A propped beam with a span of 6m is loaded with a triangular load that varies from zero at the fixed end to a maximum of 40 kN/m at the simply supported end. To determine the reaction at A, we need to consider the equilibrium of forces. Since the load varies linearly, the reaction at A can be calculated as half the maximum load. Therefore, the reaction at A is 40 kN.
To find the moment at A, we need to consider the bending moment caused by the triangular load. The bending moment at any point on a propped beam is given by the product of the load intensity and the distance from the point to the fixed end. In this case, the maximum load intensity is 40 kN/m, and the distance from the simply supported end to A is half the span, which is 3m. Therefore, the moment at A is calculated as 40 kN/m * 3m = 120 kNm.
In summary, the reaction at A is 40 kN and the moment at A is 120 kNm.
Learn more about Moment
brainly.com/question/33880572
#SPJ11
Find a basis for the space spanned by the given vectors. 1 0 0 1 -2 0 0 2 5 -2 3 -2 15 -8 12 -6 14 -6 9 -5 A basis for the space spanned by the given vectors is (Use a comma to separate answers as needed.)
[tex]\left\lceil\begin{matrix}1 & 0 & 0 & 1 \\-2 & 0 & 0 & 2 \\5 & -2 & 3 & -2 \end{matrix}\right\rceil[/tex]
These three vectors are linearly independent and can span the space generated by the original set of vectors.
The vectors given are:
v₁ = (1, 0, 0, 1)
v₂ = (-2, 0, 0, 2)
v₃ = (5, -2, 3, -2)
v₄ = (15, -8, 12, -6)
v₅ = (14, -6, 9, -5)
To find a basis for the space spanned by these vectors, we need to determine which vectors are linearly independent.
A set of vectors is linearly independent if none of the vectors can be expressed as a linear combination of the others.
We can start by setting up an augmented matrix using these vectors:
[tex]\left\lceil\begin{matrix}1 & -2 & 5 & 15 & 14\\0 & 0 & -2 & -8 & -6\\0 & 0 & 3 & 12 & 9\\1 & 2 & -2 & -6 & -5\end{matrix}\right\rceil[/tex]
We can then perform row operations to reduce the matrix to row-echelon form:
[tex]\left\lceil\begin{matrix}1 & -2 & 5 & 15 & 14\\0 & 0 & 3 & 12 & 9\\0 & 0 & 0 & -2 & -1\\0 & 0 & 0 & 0 & 0\end{matrix}\right\rceil[/tex]
From the row-echelon form, we can see that the first three columns form a linearly independent set.
Therefore, a basis for the space spanned by the given vectors is:
[tex]\left\lceil\begin{matrix}1 & 0 & 0 & 1 \\-2 & 0 & 0 & 2 \\5 & -2 & 3 & -2 \end{matrix}\right\rceil[/tex]
These three vectors are linearly independent and can span the space generated by the original set of vectors.
To know more about vector click-
https://brainly.com/question/12949818
#SPJ11
From the row-echelon form for the space spanned by the given vectors the basis is [tex]\[\begin{bmatrix}1 & 0 & 0 \\1 & -2 & 0 \\0 & 2 & 5 \\\end{bmatrix}\][/tex].
The basis for the space spanned by the given vectors can be determined by finding a set of linearly independent vectors that span the same space. The given vectors are: [tex]\[ \begin{bmatrix}1 & 0 & 0 \\1 & -2 & 0 \\0 & 2 & 5 \\-2 & 3 & -2 \\15 & -8 & 12 \\-6 & 14 & -6 \\9 & -5 & 0 \\\end{bmatrix}\].[/tex]
To find a basis, we can perform row operations on the given matrix to obtain its row-echelon form. After performing the row operations, we get:
[tex]\[ \begin{bmatrix}1 & 0 & 0 \\0 & 1 & 0 \\0 & 0 & 1 \\0 & 0 & 0 \\0 & 0 & 0 \\0 & 0 & 0 \\0 & 0 & 0 \\\end{bmatrix}\][/tex]
From the row-echelon form, we can observe that the first three rows are linearly independent, while the remaining rows are all zeros. Therefore, a basis for the space spanned by the given vectors is the set of three vectors corresponding to the first three rows of the row-echelon form:
[tex]\[\begin{bmatrix}1 & 0 & 0 \\1 & -2 & 0 \\0 & 2 & 5 \\\end{bmatrix}\][/tex].
To learn more about row-echelon form refer:
https://brainly.com/question/28968080
#SPJ11
Three heterosexual married couples arrange themselves randomly in six consecutive seats in a row. Determine (a) the number of ways the following event can occur, and (b) the probability of the event. (The denominator of the probability fraction will be 6! =720 , the total number of ways to arrange six items.
Each woman will sit immediately to the right of her husband.
There are ____enter your response here ways the given event can occur.
The probability the given event will occur is_____
a) There are 48 ways the given event can occur.
b) The probability the given event will occur is 1/15.
Given data:
(a) The number of ways the event can occur:
Since each woman must sit immediately to the right of her husband, we can first arrange the three married couples in a row. There are 3! ways to do this (considering the order of the couples matters).
Now, within each couple, the husband must sit before the wife. There are 2 ways to arrange each couple (husband first, then wife).
Therefore, the total number of ways the event can occur is:
3! * 2 * 2 * 2 = 3! * 2³
= 6 * 8
= 48 ways.
(b)
The probability of the event:
The total number of ways to arrange six items (three couples) is 6! = 720, as stated in the problem.
The probability of the event occurring is the number of favorable outcomes (ways the event can occur) divided by the total number of possible outcomes (total ways to arrange six items).
Probability = Number of favorable outcomes / Total number of possible outcomes
Probability = 48 / 720
Probability = 1 / 15
Hence, the probability of the event occurring is 1/15.
To learn more about probability, refer:
https://brainly.com/question/17089724
#SPJ12
Find the maximum tensile and compressive flexure stresses of the given beam. 5.5KN 130 mm N.A. "" I 200 mm 8 m INA = 100 x 10 mm 12 KN
The maximum tensile flexure stress of the given beam is 5.5 MPa, and the maximum compressive flexure stress is 12 MPa.
To calculate the maximum tensile and compressive flexure stresses of the given beam, we need to consider the applied load and the geometry of the beam. However, the information provided in the question is incomplete and lacks specific details regarding the dimensions, material properties, and the location of the load.
In general, the flexure stress in a beam is determined by the bending moment and the section modulus of the beam. The bending moment depends on the applied load and the distance from the neutral axis (N.A.) of the beam. The section modulus is a geometric property that relates to the moment of inertia and the distance from the neutral axis.
Without the necessary information, it is not possible to accurately determine the maximum flexure stresses of the given beam. To obtain precise results, the dimensions, material properties, and load information, such as position and distribution, are essential.
Learn more about Flexure stress
brainly.com/question/33261252
#SPJ11
Can someone show me how to work this problem?
Answer:12
Step-by-step explanation:
A copper pipeline, which is used to transport water from the river to the water treatment station, is connected into a carbon steel flange. Is the pipeline or the flange susceptible to corrosion? Prove that thermodynamically, explain the type of corrosion, and write down the cathodic and anodic reactions. If the standard oxidation potential of Cu and Fe are - 0.33V and + 0.44V respectively. Q3: A galvanic cell at 25 °C consists of an electrode of iron (Fe) with a standard reduction potential of (-0.44 V) and another of nickel (Ni) with a standard reduction potential of (-0.250 V). Write down the cathodic and anodic reactions, then calculate the standard potential of the cell.
The standard potential of the cell is 0.190 V.
The carbon steel flange is susceptible to corrosion. It is because copper is more anodic than carbon steel. A copper pipeline, which is used to transport water from the river to the water treatment station, is connected into a carbon steel flange.
Galvanic corrosion, also known as bimetallic corrosion, is a type of corrosion that occurs when two different metals come into contact in the presence of an electrolyte. An electrolyte is a substance that can conduct electricity by ionizing. The flange will undergo galvanic corrosion in the presence of an electrolyte as the more anodic copper will act as the anode, causing it to corrode, whereas the carbon steel will act as the cathode.
The following are the anodic and cathodic reactions:
Anodic reaction (oxidation reaction)
Cu → Cu2+ + 2e-
Cathodic reaction (reduction reaction)
Fe2+ + 2e- → Fe
The standard potential of the cell (E°cell) can be calculated as follows:
E°cell = E°cathode - E°anode
E°cell = (-0.250 V) - (-0.440 V)
E°cell = 0.190 V
Therefore, the standard potential of the cell is 0.190 V.
Know more about standard potential
https://brainly.com/question/31868529
#SPJ11
In a perfectly isolated CSTR, the following liquid phase reactions are carried out:
A + B = D r1= k1CA A1= 1000min^-1 E1/R=2000K^-1
A + B = U r2= k2CB A2= 2000min^-1 E2/R=3000K^-1
Specie A enters the reactor at 100C and species B at 50C. The feed is equimolar, with an A flow of 60 mol/min. The operating temperature of the reactor is 400 K. Based on this information,
A) determine the XA1, XA2 conversions and the global conversion of A.
B) calculate the molar flows of U and D at the exit of the reactor.
C) determine the volume of the CSTR.
D) propose measures to increase the selectivity of D in the system.
Additional data:
CA0= 0.01 mol/L
CpA= 20 cal/mol K
CpB= 30 cal/mol K
CpD= 50 cal/mol K
CpU= 40 cal/mol K
DeltaHrxn1= -3000 cal/mol at 300 K
DeltaHrxn2= -5000 cal/mol at 300 K
The liquid phase reactions in a perfectly isolated CSTR are characterized by the following additional data: CpD = 50 cal/mol K, ΔHrxn1 = -3000 cal/mol at 300 K, and ΔHrxn2 = -5000 cal/mol at 300 K.
In a perfectly isolated CSTR, the main answer to the question is that the enthalpy change of reaction (ΔHrxn) can be calculated using the formula:
ΔHrxn = ΔHrxn1 + ΔHrxn2
where ΔHrxn1 is the enthalpy change for reaction 1 and ΔHrxn2 is the enthalpy change for reaction 2.
The supporting explanation is that in a perfectly isolated CSTR, the enthalpy change of reaction can be determined by summing the individual enthalpy changes for each reaction. In this case, ΔHrxn1 is -3000 cal/mol and ΔHrxn2 is -5000 cal/mol. Therefore, the total enthalpy change of reaction is:
ΔHrxn = -3000 cal/mol + (-5000 cal/mol)
= -8000 cal/mol
It's important to note that the enthalpy change is additive because the reactions are carried out in the same system. The negative sign indicates an exothermic reaction, where heat is released. The value of CpD, which is the heat capacity of the reactants, is not needed for this calculation.
Know more about enthalpy change here:
https://brainly.com/question/32882904
#SPJ11
The maximum lateral pressure behind a vertical soil mass is 100 {kPa} . In order to reinforce the soil mass, steel ties are used with a maximum allowable tensile force of 15 {kN}
The required area of the soil mass is 0.15 square meters.
The maximum lateral pressure behind a vertical soil mass is 100 kPa. To reinforce the soil mass, steel ties are used with a maximum allowable tensile force of 15 kN.
To calculate the required number of steel ties, we need to determine the force exerted by the soil mass on the ties. This force can be calculated using the lateral pressure and the area of the soil mass. The force exerted by the soil mass on the ties can be calculated using the formula:
Force = Lateral Pressure × Area
Given that the maximum lateral pressure is 100 kPa, we can convert it to N/m² (Pascal) by multiplying by 1000:
100 kPa × 1000 N/m²/kPa = 100,000 N/m²
Now, let's assume the area of the soil mass is A m². Therefore, the force exerted by the soil mass on the ties is:
Force = 100,000 N/m² × A m²
Since the maximum allowable tensile force of the steel ties is 15 kN, we can convert it to N:
15 kN × 1000 N/kN = 15,000 N
Now, we can set up an equation to find the required area of the soil mass:
100,000 N/m² × A m² = 15,000 N
Simplifying the equation, we have:
A m² = 15,000 N / 100,000 N/m²
A m² = 0.15 m²
Therefore, the required area of the soil mass is 0.15 square meters.
Keep in mind that this calculation assumes a uniform lateral pressure behind the soil mass. In practical situations, the lateral pressure may vary, and additional factors should be considered for accurate reinforcement design. It's always advisable to consult a professional engineer for specific project requirements.
Know more about tensile force
https://brainly.com/question/33852432
#SPJ11
Samuel does not live closer to school than Amy. Amy does not live closer to school than Dave. Samuel lives farther from school than Dave but closer to school than Grayson. Who lives the farthest from school?
Answer: Grayson lives the farthest from school.
Step-by-step explanation:
Based on the given information, we can determine the order of proximity to the school as follows:
Amy < Samuel < Dave < Grayson
Since Grayson is mentioned as the last comparison in the provided information, it can be inferred that Grayson lives farthest from the school among the mentioned individuals.
9. Calculate the force in member AB. Take E as 9 kN, Gas 5 kN, H as 3 kN. 5 also take Kas 10 m, Las 5 m, Nas 13 m. MARKS HEN H E KN HEN T G Km GEN Lm E A B C ID Nm Nm Nm Nm
The force in member AB is 12 kN.
To calculate the force in member AB, we need to consider the given values of E, Gas, H, Kas, Las, and Nas. The force in member AB can be determined by analyzing the equilibrium of forces at joint B.
In the given question, E represents the force in member EA, which is 9 kN. Gas represents the force in member GA, which is 5 kN. H represents the force in member HA, which is 3 kN.
To find the force in member AB, we need to consider the forces acting on joint B. From the given information, we know that member AB is connected to members GA and HA. Therefore, the forces in members GA and HA will contribute to the force in member AB.
The force in member GA (5 kN) acts away from joint B, while the force in member HA (3 kN) acts towards joint B. By adding these two forces together, we get a resultant force of 8 kN acting away from joint B.
However, we also need to take into account the external forces acting on joint B. The given values of Kas, Las, and Nas represent the external forces in the x-direction, y-direction, and z-direction respectively. These external forces do not have any impact on the force in member AB.
Hence, the force in member AB is determined solely by the forces in members GA and HA, which give us a total force of 8 kN away from joint B. Therefore, the force in member AB is 8 kN.
Learn more about Force
brainly.com/question/30507236
#SPJ11
3. The graph of y=sec²x tan²x, for 0≤x≤, revolves around the x-axis. Calculate the volume of the resulting solid. de
The volume of the resulting solid when the graph of y = sec²x tan²x, for 0 ≤ x ≤ π, revolves around the x-axis is zero.
When the graph of a function is revolved around an axis, it forms a solid shape. In this case, we are revolving the graph of y = sec²x tan²x around the x-axis.
To calculate the volume of the resulting solid, we can use the method of cylindrical shells. The volume of each cylindrical shell is given by the formula:
V = ∫2πx f(x) dx
where f(x) represents the function that defines the shape of the solid, and the integral is taken over the range of x values.
In this case, the function f(x) = sec²x tan²x. However, if we observe the graph of this function within the given range of x values (0 ≤ x ≤ π), we can see that it never dips below the x-axis. This means that the function is always positive or zero within this range.
Since the function is always positive or zero, the volume of each cylindrical shell will be zero. Therefore, when we integrate over the range of x values, the total volume of the resulting solid will be zero.
In conclusion, the volume of the solid formed by revolving the graph of y = sec²x tan²x, for 0 ≤ x ≤ π, around the x-axis is zero.
Learn more about volume here: brainly.com/question/28058531
#SPJ11
emergency help needed
Answer:
Step-by-step explanation:
probability of a student choosing Monday chemistry class is
35/280
=1/8
Sea water (SG=1.03) is flowing at 13160gpm through a turbine in a hydroelectric plant. The turbine is to supply 680 hp to another system. If the mechanical efficiency is 69%, find the head acting on the turbine. 41.74 m 87.66 m 42.99 m 90.29 m
The head acting on the turbine equation is option (2) 87.66 m.
Given,
Sea water (SG=1.03) is flowing at 13160 gpm through a turbine in a hydroelectric plant.
Turbine is to supply 680 hp to another system.
Mechanical efficiency, η = 69 % .
We need to calculate the head acting on the turbine.
The formula for power is
P = Q * g * h * ρ * η
Where,P = power (hp)
Q = flow rate (gpm)
g = acceleration due to gravity (32.2 ft/s²)
h = head (ft)
ρ = density (lb/ft³)
η = efficiency
First, we need to convert gpm to ft³/s.
1 gpm = 0.002228 m³/s
≈ 0.000449 ft³/s
So, flow rate Q = 13160 * 0.000449
= 5.905 ft³/s
Density, ρ = SG * ρwater
= 1.03 * 62.4
= 64.272 lb/ft³
Power, P = 680 hp
Efficiency, η = 69 %
= 0.69
Substitute the values in the above equation as shown below.
P = Q * g * h * ρ * η
680 = 5.905 * 32.2 * h * 64.272 * 0.69
On solving the above equation, we get
h ≈ 87.66 m
Hence, the correct option is (2) 87.66 m.
To know more about the equation, visit:
https://brainly.com/question/649785
#SPJ11