The potential difference between the plates of a parallel-plate capacitor with an area of [tex]2 m^2[/tex], separation of 0.0002 m, and a charge of 0.0001 C is 1130 volts.
The potential difference (V) between the plates of a capacitor can be determined using the formula
V = q / C
where q is the charge and C is the capacitance.
The capacitance of a parallel-plate capacitor is given by the formula:
[tex]C = \epsilon_0 * (A / d)[/tex]
where [tex]\epsilon_0[/tex] is the permittivity of free space, A is the area of the plates, and d is the separation between the plates.
Plugging in the values, the capacitance can be calculated as:
[tex]C = (8.85 * 10^{-12} F/m) * (2 m^2 / 0.0002 m) = 88.5 * 10^{-12} F[/tex].
Now, substituting the capacitance and charge values into the potential difference formula,
[tex]V = (0.0001 C) / (88.5 * 10^{-12} F) = 1130 volts[/tex].
Therefore, the potential difference between the plates of the parallel-plate capacitor is 1130 volts.
Learn more about capacitor here:
https://brainly.com/question/31627158
#SPJ11
The resistance of a wire, made of a homogenous material with a uniform diameter, is proportional to its length. Select one: True False
False. The resistance of a wire made of a homogeneous material with a uniform diameter is not proportional to its length.
According to Ohm's law, the resistance (R) of a wire is determined by its resistivity (ρ), length (L), and cross-sectional area (A). The relationship is given by the equation R = ρ * (L/A). From this equation, we can see that the resistance depends on both the length and the cross-sectional area of the wire.
When the length of the wire increases, the resistance also increases. This is because the longer wire provides more obstacles for the flow of electric current, resulting in higher resistance. However, the relationship between resistance and length is not directly proportional but rather linear.
In a wire with a uniform diameter, the cross-sectional area remains constant throughout its length. Therefore, the resistance is directly proportional to the length of the wire, assuming the resistivity of the material remains constant.
Learn more about resistance here:
https://brainly.com/question/29427458
#SPJ11
1. You have a grindstone (a disk) that is 94.0 kg, has a 0.400-m radius, and is turning at 85.0 rpm, and you press a steel axe against it with a radial force of 16.0 N.
(a) Assuming the kinetic coefficient of friction between steel and stone is 0.40, calculate the angular acceleration (in rad/s2) of the grindstone. (Indicate the direction with the sign of your answer.)
____rad/s2
(b)How many turns (in rev) will the stone make before coming to rest?
2.A gyroscope slows from an initial rate of 52.3 rad/s at a rate of 0.766 rad/s2.
(a)How long does it take (in s) to come to rest? ANSWER: (68.3s)
(b)How many revolutions does it make before stopping?
3.Calculate the moment of inertia (in kg·m2) of a skater given the following information.
(a)The 68.0 kg skater is approximated as a cylinder that has a 0.150 m radius.
0.765 kg·m2
(b)The skater with arms extended is approximately a cylinder that is 62.0 kg, has a 0.150 m radius, and has two 0.850 m long arms which are 3.00 kg each and extend straight out from the cylinder like rods rotated about their ends.
______kg·m2
Answer: 1a) The angular acceleration of the grindstone is -0.847 rad/s².1b) The grindstone makes 10.4 turns before coming to rest.
Answer:2a) The gyroscope takes 68.3 seconds to come to rest.2b) The gyroscope makes 352.6 revolutions before stopping.
Answer:3a) The moment of inertia of the skater is 0.765 kg·m².3b) The moment of inertia of the skater with arms extended is 2.475 kg·m².
1a) The angular acceleration of the grindstone is given by the formula τ = I α, where τ is the torque, I is the moment of inertia, and α is the angular acceleration. The torque τ is given by τ = Fr, where F is the force and r is the radius. Hence, we have:F = 16.0 N and r = 0.400 m.
The moment of inertia of a solid disk is given by I = (1/2) MR², where M is the mass and R is the radius. Hence, we have:M = 94.0 kg and R = 0.400 m.Substituting these values into the formula τ = I α, we get:τ = Fr = (16.0 N) (0.400 m) = 6.40 N.mI = (1/2) MR² = (1/2) (94.0 kg) (0.400 m)² = 7.552 kg.m²α = τ / I = (6.40 N.m) / (7.552 kg.m²) = 0.847 rad/s²The angular acceleration of the grindstone is 0.847 rad/s², in the direction opposite to its rotation.
1b) The final angular velocity of the grindstone is zero. Hence, we can use the formula ω² = ω₀² + 2αθ, where ω₀ is the initial angular velocity, θ is the angular displacement, and ω is the final angular velocity. Since the grindstone comes to a stop, we have ω = 0. Also, the angular displacement is given by θ = (2π)n, where n is the number of turns.
Substituting these values into the formula, we get:ω² = ω₀² + 2αθ0 = (85.0 rpm) (2π / 60 s/min) = 8.90 rad/sSubstituting these values into the formula, we get:0 = (8.90 rad/s)² + 2(-0.847 rad/s²)(2π)nSolving for n, we get:n = 10.4 revThe grindstone makes 10.4 turns before coming to rest.
Answer: 1a) The angular acceleration of the grindstone is -0.847 rad/s².1b) The grindstone makes 10.4 turns before coming to rest.
2a) The initial rate of the gyroscope is ω₀ = 52.3 rad/s, and the angular deceleration is α = -0.766 rad/s². We can use the formula ω = ω₀ + αt, where t is the time. Solving for t, we get:t = (ω - ω₀) / αSubstituting the values, we get:t = (0 - 52.3 rad/s) / (-0.766 rad/s²) = 68.3 sThe gyroscope takes 68.3 seconds to come to rest.
2b) The number of revolutions is given by the formula θ = ω₀t + (1/2) αt², where θ is the angular displacement. Since the final angular displacement is zero, we have:0 = ω₀t + (1/2) αt²Substituting the values, we get:0 = (52.3 rad/s) t + (1/2) (-0.766 rad/s²) t²Solving for t using the quadratic formula, we get:t = 68.3 s (same as part a)The number of revolutions is given by the formula θ = ω₀t + (1/2) αt². Substituting the values, we get:θ = (52.3 rad/s) (68.3 s) + (1/2) (-0.766 rad/s²) (68.3 s)² = 2217 radThe gyroscope makes 2217 / (2π) = 352.6 revolutions before stopping.Answer:2a) The gyroscope takes 68.3 seconds to come to rest.2b) The gyroscope makes 352.6 revolutions before stopping.
3a) The moment of inertia of a solid cylinder is given by the formula I = (1/2) MR², where M is the mass and R is the radius. Hence, we have:M = 68.0 kg and R = 0.150 m.Substituting these values into the formula, we get:I = (1/2) (68.0 kg) (0.150 m)² = 0.765 kg.m²The moment of inertia of the skater is 0.765 kg·m².
3b) The moment of inertia of a thin rod rotated about one end is given by the formula I = (1/3) ML², where M is the mass and L is the length. Hence, we have:M = 3.00 kg and L = 0.850 m.Substituting these values into the formula, we get:I = (1/3) (3.00 kg) (0.850 m)² = 0.683 kg.m²The moment of inertia of each arm is 0.683 kg·m².The moment of inertia of the skater with arms extended is the sum of the moment of inertia of the cylinder and the moment of inertia of the two arms, assuming they are rotated about the center of mass of the skater. The moment of inertia of a cylinder rotated about its center of mass is given by the formula I = (1/2) MR².
The center of mass of the skater with arms extended is at the center of the cylinder. Hence, we have:M = 62.0 kg and R = 0.150 m.Substituting these values into the formula, we get:Icyl = (1/2) (62.0 kg) (0.150 m)² = 1.109 kg.m²The moment of inertia of the cylinder is 1.109 kg·m².The moment of inertia of the skater with arms extended is given by the formula I = Icyl + 2Iarm = 1.109 kg·m² + 2(0.683 kg·m²) = 2.475 kg·m²The moment of inertia of the skater with arms extended is 2.475 kg·m².
Answer:3a) The moment of inertia of the skater is 0.765 kg·m².3b) The moment of inertia of the skater with arms extended is 2.475 kg·m².
Learn more about Velocity here,
https://brainly.com/question/80295
#SPJ11
An electron is at the origin.
(a) Calculate the electric potential VA at point A, x = 0.315 cm.
V
(b) Calculate the electric potential VB at point B, x = 0.605 cm.
V
What is the potential difference VB - VA?
V
(c) Would a negatively charged particle placed at point A necessarily go through this same potential difference upon reaching point B? Explain
In the given scenario, the electric potential at point A (x = 0.315 cm) is calculated, resulting in VA. Similarly, the electric potential at point B (x = 0.605 cm) is calculated, resulting in VB. The potential difference VB - VA is then determined.
To calculate the electric potential at point A (VA), we need to determine the potential due to the electron's charge. The electric potential at a point due to a point charge can be calculated using the equation V = k * q / r, where V is the electric potential, k is the electrostatic constant, q is the charge, and r is the distance from the charge. Plugging in the values, we can calculate VA.
Similarly, to calculate the electric potential at point B (VB), we use the same formula with the given distance.
The potential difference VB - VA can be obtained by subtracting the value of VA from VB. This yields the difference in electric potential between the two points.
When a negatively charged particle is placed at point A and moves towards point B, it will experience a change in electric potential. However, whether it goes through the same potential difference depends on the path taken. If the path from A to B is along equipotential surfaces (lines of constant electric potential), the potential difference will be the same. However, if the path deviates and crosses different equipotential surfaces, the potential difference experienced by the particle may be different. The potential difference is only the same when the path is along equipotential surfaces.
Learn more about potential difference here:
https://brainly.com/question/23716417
#SPJ11
Consider standing waves in the column of air contained in a pipe of length L = 1.5 m. The speed of sound in the column is vs = 346 m/s.
Each of the standing wave images provided may represent a case for which one or both ends are open. Larger dots indicate higher air pressure in a given area of the column.
20% Part (b) Calculate the wavelength λ3, in meters, for the third harmonic in the pipe with two open ends.
20% Part (c) Calculate the frequency f1, in hertz, for the fundamental harmonic in the pipe with two open ends.
20% Part (d) Select the image from the options provided showing the gas pressure in the fourth mode of a pipe with one open end and one closed end. (The fourth mode is the third excitation above the fundamental.)
20% Part (e) Calculate the frequency f1, in hertz, for the fundamental harmonic in the pipe with one open and one closed end.
(b)The wavelength.λ3 = 2.0 m.(c)The frequency f1= 115.33 Hz.(d)The image that shows the gas pressure in the fourth mode of a pipe with one open end and one closed end is Image Y. (e)the frequency f1= 57.67 Hz.
Standing waves in the column of air contained in a pipe of length L = 1.5 m, where the speed of sound in the column is vs = 346 m/s. Each of the standing wave images provided may represent a case for which one or both ends are open. Larger dots indicate higher air pressure in a given area of the column.
Part (b) Calculation of λ3:For the third harmonic, there are three antinodes and two nodes, so there are four regions of the pipe that are a quarter of the wavelength.λ3 = 4L/3 = (4 × 1.5)/3 = 2.0 m.
Part (c) Calculation of f1:For the first harmonic, the wavelength is equal to the length of the pipe since there is one antinode and two nodes.f1 = vs/λ1 = vs/2L = 346/(2 × 1.5) = 115.33 Hz.
Part (d) Identification of image:A closed end implies an antinode of pressure, while an open end implies a node of pressure. The image that shows the gas pressure in the fourth mode of a pipe with one open end and one closed end is Image Y.
Part (e) Calculation of f1:For the first harmonic in a pipe with one open and one closed end, the wavelength is four times the length of the pipe, since there is an antinode at the open end, a node at the closed end, and two nodes in between.f1 = vs/λ1 = vs/4L = 346/(4 × 1.5) = 57.67 Hz.
Learn more about antinodes here,
https://brainly.com/question/11735759
#SPJ11
A plain carbon steel wire 3 mm in diameter is
to offer a resistance of no more than 20 . (0.6x10^7) electrical conductivity , compute the maximum
wire length.
To achieve a resistance of no more than 20 Ω with a plain carbon steel wire of 3 mm diameter and an electrical conductivity of 0.6x10^7, the maximum wire length can be computed.
The resistance (R) of a wire can be calculated using the formula R = (ρ * L) / A, where ρ is the electrical resistivity of the material, L is the length of the wire, and A is the cross-sectional area of the wire.
In this case, the desired resistance is 20 Ω, and the electrical conductivity (σ) is the reciprocal of the resistivity (ρ), so ρ = 1/σ. The cross-sectional area (A) can be calculated using the formula A = π * r^2, where r is the radius of the wire (half of the diameter).
To find the maximum wire length, we rearrange the resistance formula as L = (R * A) / ρ. Substituting the given values, we have L = (20 * π * (1.5x10^-3)^2) / (1 / (0.6x10^7)).
By evaluating this expression, we can determine the maximum wire length required to achieve the desired resistance of no more than 20 Ω.
To know more about electrical conductivity click here:
https://brainly.com/question/862085
#SPJ11
A 110g mass on a spring oscillates on a frictionless horizontal surface with a period of 0.60s and an amplitude of 18.0cm. Determine the:
a) Spring constant
b) Maximum spring potential energy of the system
c) Maximum speed of the mass
a)The spring constant of the system is 12.16 N/m. b).The maximum potential energy stored in the spring is 0.198 J. c)The maximum speed of the mass is 1.89 m/s.
a) Spring Constant k is given by the formula;k= 4π²m/T²where;T is the time periodm is the massk is the spring constantSubstitute the given values;m = 110g = 0.110kgT = 0.60 sTherefore;k = (4 x 3.14² x 0.110)/(0.60)² = 12.16 N/mTherefore, the spring constant of the system is 12.16 N/m.
b) Maximum spring potential energy of the systemThe maximum potential energy stored in the spring during its oscillations is given by the formula;U = (1/2) kx²where; x is the amplitude of the oscillationSubstitute the given values;k = 12.16 N/mx = 18.0 cm = 0.18 mTherefore;U = (1/2) x k x² = 0.5 x 12.16 x (0.18)² = 0.198 JTherefore, the maximum potential energy stored in the spring is 0.198 J.
c) Maximum speed of the massThe maximum speed of the mass can be obtained using the formula;vmax= Aωwhere;A is the amplitude ω is the angular velocity.Substitute the given values;A = 18.0 cm = 0.18 mω = 2π/T = 2 x 3.14/0.60Therefore;vmax = Aω = 0.18 x 2 x 3.14/0.60vmax = 1.89 m/sTherefore, the maximum speed of the mass is 1.89 m/s.
Learn more about amplitude here,
https://brainly.com/question/3613222
#SPJ11
A parallel plate capacitor, in which the space between the plates is filled with a dielectric material with dielectric constant k = 10.1, has a capacitor of C= 6.2μF and it is connected to a battery whose voltage is V = 5.9V and fully charged. Once it is fully charged, it is disconnected from the battery and without affecting the charge on the plates, dielectric material is removed from the capacitor. How much change occurs in the energy of the capacitor (final energy minus initial energy)? Express your answer in units of mJ (mili joules) using two decimal places
The change in energy of the capacitor (final energy minus initial energy) is 2.11 mJ.
When the dielectric material is removed from the capacitor, the capacitance decreases, and the voltage across the plates increases to keep the charge constant. Let's calculate the initial energy stored in the capacitor as well as the final energy stored in the capacitor.Energy stored by a capacitor is given by:U = 1/2 CV²Initial energy,U1 = 1/2 × 6.2 × (5.9)² U1 = 102.43 mJWhen the dielectric material is removed from the capacitor, the capacitance changes.
Capacitance without the dielectric material,C2 = C / k C2 = 6.2 μF / 10.1 C2 = 0.613 μFThe voltage across the plates increases.V2 = V × k V2 = 5.9 V × 10.1 V2 = 59.59 VFinal energy,U2 = 1/2 × 0.613 × (59.59)² U2 = 104.54 mJChange in energy,ΔU = U2 - U1 ΔU = 104.54 - 102.43 ΔU = 2.11 mJTherefore, the change in energy of the capacitor (final energy minus initial energy) is 2.11 mJ.
Learn more about Energy here,
https://brainly.com/question/2003548
#SPJ11
Find solutions for your homework
science
earth sciences
earth sciences questions and answers
no need explanation, just give me the answer pls 12. what is the origin of the moon? a. the moon was once a part of earth and was ejected from earth in the early solar system. b. the moon formed from debris following a major impact between earth and another astronomical body. c. the moon was captured by
Question: No Need Explanation, Just Give Me The Answer Pls 12. What Is The Origin Of The Moon? A. The Moon Was Once A Part Of Earth And Was Ejected From Earth In The Early Solar System. B. The Moon Formed From Debris Following A Major Impact Between Earth And Another Astronomical Body. C. The Moon Was Captured By
No need explanation, just give me the answer pls
12. What is the origin of the moon?
A.The moon was once a part of Earth and was ejected from Earth in the early solar system.B.The moon formed from debris following a major impact between Earth and another astronomical body.C.The moon was captured by Earth's gravity but formed elsewhere.D.The moon formed with Earth near where it is today.E.The correct answer is not given.
The answer to the question, "What is the origin of the moon?" is B. The moon formed from debris following a major impact between Earth and another astronomical body.
This theory, known as the giant impact hypothesis or the impactor theory, proposes that early in the history of the solar system, a Mars-sized object, often referred to as "Theia," collided with a young Earth. The impact was so powerful that it ejected a significant amount of debris into space. Over time, this debris coalesced to form the moon.
According to this hypothesis, the collision occurred approximately 4.5 billion years ago. The ejected material eventually formed a disk of debris around Earth, which then accreted to form the moon. The moon's composition is similar to Earth's outer layers, supporting the idea that it originated from Earth's own materials.
The giant impact hypothesis provides an explanation for various characteristics of the moon, such as its size, composition, and its orbit around Earth. It is currently the most widely accepted theory for the moon's origin, although further research and analysis continue to refine our understanding of this fascinating event in our solar system's history.
Learn more about astronomical
https://brainly.com/question/1764951
#SPJ11
A tree projecting its image covers the height of a plane mirror of 5 cm when the mirror is 50 cm in front of an observer and in a vertical position. What is the height of the tree in meters?
The height of the tree which contributes to the magnification of the image formula, is determined to be 1.25 meters.
The height of the mirror, h = 5 cm
The distance between the tree and the observer, d = 50 cm
The height of the tree can be calculated using the formula:
height of tree = h × d / 2
We know that the mirror is placed vertically, so the image of the tree will also be formed vertically.
Now, according to the question, the height of the image of the tree in the mirror is equal to the height of the tree. Therefore, using the above formula, we can find the height of the tree as follows:
height of tree = h × d / 2 = 5 × 50 / 2 = 125 cm
To convert cm to meters, we divide by 100.
Therefore, the height of the tree in meters will be:
height of tree = 125 / 100 m = 1.25 m
Hence, the height of the tree is 1.25 meters.
Learn more about magnification at: https://brainly.com/question/29314559
#SPJ11
The acceleration of a block attached to a spring is given by - (0.346m/s²) cos ([2.29rad/s]t). Part A What is the frequency of the block's motion? f = ________ Hz
Part B What is the maximum speed of the block? vmax = _____________ m/s
Answer: Therefore, the frequency of the block's motion is f = 0.834 Hz and the maximum speed of the block is vmax = 0.793 m/s.
The acceleration of a block attached to a spring is given by - (0.346m/s²) cos ([2.29rad/s]t)
Part A: The frequency of the block's motion:
Frequency is defined as the number of cycles per second. The equation of motion of an oscillating block attached to a spring is given as:
a = -ω²x
where, ω = 2πf ;a = acceleration of the oscillating block attached to a spring, ω = angular frequency, f = frequency, x = displacement.
Thus,ω² = (2.29 rad/s)²
= 5.2441 rad²/s²
ω = 2πf
= 5.2441f
= 0.834 Hz
Part B: The maximum speed of the block vmax =
vmax = (1/ω) * maximum value of a(1/ω) = 1/ (2.29 rad/s) = 0.4365 s.
Thus, vmax = (0.346 m/s²)/ 0.4365 s
= 0.793 m/s
Therefore, the frequency of the block's motion is f = 0.834 Hz and the maximum speed of the block is vmax = 0.793 m/s.
Learn more about frequency: https://brainly.com/question/254161
#SPJ11
A soap film with a refractive index of 1.5 has a thickness of 300 nm. If the
wall of the bubble is illuminated by white light, what is the color of the
reflected light that we can see?
The soap film with a refractive index of 1.5 and a thickness of 300 nm will reflect light with interference patterns. The reflected light will appear as a combination of colors due to the interference of different wavelengths.
When white light illuminates the soap film, it consists of a range of wavelengths corresponding to different colors. As the light passes through the film, some of it reflects off the outer surface, while some passes through and reflects off the inner surface. The reflected light waves interfere with each other, resulting in constructive and destructive interference.
The interference patterns depend on the thickness of the film and the wavelength of light. The thickness of the soap film (300 nm) is comparable to the wavelength of visible light, causing significant interference. The colors we perceive are the result of constructive interference for certain wavelengths and destructive interference for others.
Since the refractive index of the soap film is 1.5, the interference patterns will be more pronounced. The specific colors observed will depend on the exact thickness of the film and the wavelengths of light that experience constructive interference. Generally, soap films produce a series of colors known as "Newton's rings" due to the interference effects, resulting in a pattern of concentric circles with changing colors.
Learn more about refractive index here:
https://brainly.com/question/30761100
#SPJ11
K=2,C=1) Describe, in your own words, how you would determine the acceleration of an object from a Velocity-time graph.
The acceleration of an object can be determined from a Velocity-time graph by analyzing the slope of the graph, either by calculating the average acceleration between two points or by determining the instantaneous acceleration at a specific point on the graph.
To determine the acceleration of an object from a Velocity-time graph, you would need to look at the slope or the steepness of the graph at a particular point.
Acceleration is defined as the rate of change of velocity over time. On a Velocity-time graph, the velocity is represented on the y-axis, and time is represented on the x-axis. The slope of the graph represents the change in velocity divided by the change in time, which is essentially the definition of acceleration.
If the slope of the graph is a straight line, the acceleration is constant. In this case, you can calculate the acceleration by dividing the change in velocity by the change in time between two points on the graph.
If the graph is curved, the acceleration is not constant but changing. In this case, you would need to calculate the instantaneous acceleration at a specific point. To do this, you can draw a tangent line to the curve at that point and determine the slope of that tangent line. The slope of the tangent line represents the instantaneous acceleration at that particular moment.
Learn more about Velocity-time graph here:
https://brainly.com/question/32254104
#SPJ11
A thin plastic lens with index of refraction - 1.73 hastal of curvature given by --106cmand Ry - 500m (a) Determine the focal length in cm of the lens -12 x cm (b) Determine whether the lens la converging or averging converging diverging Determine the image distances in om forbject stances of innom, and to (5) Infinity -12 x cm (d) 4,00 cm cm (e) 40.0 cm
The thin plastic lens with an index of refraction of 1.73 has a radius of curvature of -106 cm and a refractive index of 500 m. The focal length of the lens is determined to be -12 cm, indicating it is a diverging lens. The image distances for object distances of infinity, -12 cm, 4.00 cm, and 40.0 cm are determined to be -0.08 cm, -12 cm, -5.13 cm, and -47.06 cm, respectively.
(a) To determine the focal length of the lens, we can use the lens formula:
1/f = (n - 1) * (1/R1 - 1/R2),
where f is the focal length, n is the refractive index, and R1 and R2 are the radii of curvature of the lens surfaces. Substituting the given values, we have:
1/f = (1.73 - 1) * (1/-106 - 1/500).
Simplifying the equation, we find f ≈ -12 cm.
(b) The sign of the focal length indicates whether the lens is converging or diverging. A positive focal length indicates a converging lens, while a negative focal length indicates a diverging lens. Since the calculated focal length is negative (-12 cm), the lens is diverging.
(c) To determine the image distance for an object distance of infinity, we can use the lens formula with the object distance (u) equal to infinity:
1/f = 1/v - 1/u.
Since 1/u is zero, the equation simplifies to 1/f = 1/v. Substituting the focal length (-12 cm), we find:
1/-12 = 1/v.
Simplifying the equation, we get v ≈ -0.08 cm, indicating a virtual image formed on the same side as the object.
(d) For an object distance of -12 cm, we can use the lens formula:
1/f = 1/v - 1/u.
Substituting the values, we have:
1/-12 = 1/v - 1/-12.
Simplifying the equation, we find v ≈ -12 cm, indicating a real image formed on the opposite side of the lens.
(e) Similarly, for object distances of 4.00 cm and 40.0 cm, we can use the lens formula to find the image distances. Substituting the values into the formula, we find the image distances to be approximately -5.13 cm and -47.06 cm, respectively. Both distances indicate real images formed on the opposite side of the lens.
Learn more about refractive index here:
https://brainly.com/question/30761100
#SPJ11
A capacitor is connected to an AC source. If the maximum current in the circuit is 0.520 A and the voltage from the AC source is given by Av = (96.6 V) sin((701)s1], determine the following. (a) the rms voltage (in V) of the source V (b) the frequency (in Hz) of the source Hz (c) the capacitance (in uF) of the capacitor PF
A capacitor is connected to an AC source. the RMS voltage of the source is approximately 0.367 V. the frequency of the source is 701 Hz. the capacitance of the capacitor is approximately 125.76 μF.
Given:
Maximum current, I_max = 0.520 A
Voltage from AC source, V = (96.6 V) sin((701)t)
To determine the required values, we can use the properties of AC circuits and the relationship between current, voltage, and capacitance.
(a) The RMS voltage (V_rms) can be calculated using the formula:
V_rms = I_max / √2
Substituting the given values:the capacitance of the capacitor is approximately 125.76 μF.
V_rms = 0.520 A / √2 ≈ 0.367 A
Therefore, the RMS voltage of the source is approximately 0.367 V.
(b) The frequency (f) of the source can be determined from the given expression:
V = (96.6 V) sin((701)t)
The general equation for a sinusoidal waveform is V = V_max sin(2πft), where f represents the frequency.
Comparing the given expression to the general equation, we can see that the frequency is 701 Hz.
Therefore, the frequency of the source is 701 Hz.
(c) The capacitance (C) of the capacitor can be calculated using the formula:
I_max = 2πfCV_max
Rearranging the equation, we get:
C = I_max / (2πfV_max)
Substituting the given values:
C = 0.520 A / (2π * 701 Hz * 96.6 V)
Converting the units, we find:
C ≈ 125.76 μF
Learn more about capacitance. here:
https://brainly.com/question/31871398
#SPJ11
A marble with a mass of 0.04 kg and a volume of 1.00×10⁻⁵ m³ is dropped in a glass of dimethyl sulfoxide, which sinks to the bottom of the glass. If dimethyl sulfoxide has a density of 1100 kg/m³, what is the magnitude of the buoyant force in newtons? Round to the nearest hundredth (0.01)
The magnitude of the buoyant force is approximately 0.11 N.
To find the magnitude of the buoyant force, we will use the following formula:
B = ρ × g × V
where
B is the magnitude of the buoyant force,
ρ is the density of the liquid,
g is the acceleration due to gravity and
V is the volume of the object displaced.
We are given the following:
mass of the marble, m = 0.04 kg
volume of the marble, V = 1.00 × 10⁻⁵ m³
density of the liquid, ρ = 1100 kg/m³
acceleration due to gravity, g = 9.81 m/s²
To find the volume of liquid displaced, we use the following formula:
V_displaced = V_object = 1.00 × 10⁻⁵ m³
The magnitude of the buoyant force is given by:
B = ρ × g × V_displaced
B = 1100 kg/m³ × 9.81 m/s² × 1.00 × 10⁻⁵ m³
B = 0.10779 N ≈ 0.11 N
Therefore, the magnitude of the buoyant force is approximately 0.11 N.
Learn more about the buoyant force:
brainly.com/question/11884584
#SPJ11
Problem/Question: Megan and Jade are two of Saturn's satellites. The distance from Megan to the center of Saturn is approximately 4.0 times farther than the distance from Jade to the center of Saturn. How does Megan's orbital period, TM, compare to that of Jade, TJ?
Potential Answer: *Would this just be "4TJ"?*
Megan's orbital period (TM) is four times longer than that of Jade (TJ).
The orbital period of a satellite is the time it takes for the satellite to complete one full orbit around its primary body. In this scenario, Megan and Jade are two of Saturn's satellites, and the distance from Megan to the center of Saturn is approximately 4.0 times greater than the distance from Jade to the center of Saturn.
According to Kepler's Third Law of Planetary Motion, the orbital period of a satellite is directly proportional to the cube root of its average distance from the center of the primary body. Since Megan's distance from Saturn is 4.0 times greater than Jade's distance, the cube root of the distances ratio would be 4.0^(1/3) = 1.587.
Therefore, Megan's orbital period (TM) would be approximately 4 times longer than that of Jade (TJ), or TM = 4TJ. This implies that Megan takes four times as long as Jade to complete one orbit around Saturn.
Learn more about orbital period here:
https://brainly.com/question/3077562
#SPJ11
A sled with mass m experiences a total force of strength F, resulting in an acceleration a. Find F (in N), if m = 6.3 kg and a = 18.0 m/s.
When a sled with a mass of 6.3 kg experiences an acceleration of 18.0 m/s, the total force exerted on it is calculated to be 113.4 N using Newton's second law of motion.
According to Newton's second law of motion, the force F exerted on an object is equal to the product of its mass and acceleration. Mathematically, this can be represented as F = m * a, where F is the force, m is the mass, and a is the acceleration.
Given that the mass of the sled is 6.3 kg and the acceleration is 18.0 m/s, we can substitute these values into the equation. Multiplying the mass and acceleration together, we have F = 6.3 kg * 18.0 m/s.
Calculating the product, we find that F = 113.4 N. Therefore, the force exerted on the sled is 113.4 Newtons.
Learn more about acceleration here:
https://brainly.com/question/2303856
#SPJ11
A separately excited DC shunt motor is driving a fan load whose torque is proportional to the square of the speed. When 100 V are applied to the motor, the current taken by the motor is 8 A, with the speed being 500 rpm. At what applied voltage does the speed reach 750 rpm and then what is the current drawn by the armature? Assume the armature circuit resistance to be 102. Neglect brush drop and mechanical losses. 2. A 4 pole lap wound DC shunt generator has a useful flux/pole of 0.07Wb. The armature winding consists of 220 turns, each of 0.042 resistance. Calculate the terminal voltage when running at 900rpm, if armature current is 50A
1. At a voltage of 155.56 V, the armature draws around 0.48 A of current; 2. At 900 revolutions per minute and 50 amps of armature current, the generator's terminal voltage is around 308 V.
1. To find the applied voltage at which the speed reaches 750 rpm, we can use the speed equation for a separately excited DC shunt motor:
N = (V - Ia * Ra) / k
Where:
N is the speed in rpm,
V is the applied voltage in volts,
Ia is the armature current in amperes,
Ra is the armature resistance in ohms,
k is a constant related to the motor's characteristics.
We are given the initial conditions:
V₁ = 100 V,
Ia₁ = 8 A,
N₁ = 500 rpm.
Solving the equation for the initial conditions, we can find the value of the constant k,
500 = (100 - 8 * 102) / k
k ≈ 0.198
Now, we can use the same equation to find the applied voltage when the speed reaches 750 rpm,
750 = (V₂ - Ia₂ * 102) / 0.198
Solving for V₂, we get,
V₂ ≈ 155.56 V
Therefore, the applied voltage at which the speed reaches 750 rpm is approximately 155.56 V. To find the current drawn by the armature at this voltage, we can rearrange the equation,
Ia₂ = (V₂ - N₂ * k) / Ra
Substituting the known values,
Ia₂ = (155.56 - 750 * 0.198) / 102
Ia₂ ≈ 0.48 A
Therefore, the current drawn by the armature at the voltage of 155.56 V is approximately 0.48 A.
2. To calculate the terminal voltage of the 4-pole lap wound DC shunt generator, we can use the following formula,
E = Φ * Z * P * N / (60 * A)
Where:
E is the terminal voltage in volts,
Φ is the useful flux per pole in Weber,
Z is the total number of armature conductors,
P is the number of poles,
N is the speed in rpm,
A is the number of parallel paths in the armature winding.
Given:
Φ = 0.07 Wb,
Z = 220,
P = 4,
N = 900 rpm,
A = 2 (assuming a two-pole armature winding). Substituting the values into the formula,
E = (0.07 * 220 * 4 * 900) / (60 * 2)
E ≈ 308 V
Therefore, the terminal voltage of the generator when running at 900 rpm and with an armature current of 50 A is approximately 308 V.
To know more about armature current, visit,
https://brainly.com/question/31886760
#SPJ4
why does the wavelength of light hydrogen emits when heated up is equal to the wavelength of light that hydrogen absorbs when you shine white light towards it.
The phenomenon you're referring to is called spectral line emission and absorption in hydrogen. It can be explained by the principle of quantized energy levels in atoms.
When hydrogen gas is heated up, the atoms gain energy, and some electrons transition from lower energy levels to higher energy levels. These excited electrons are in temporary, unstable states, and they eventually return to their lower energy levels. During this transition, the excess energy is emitted in the form of photons, which we perceive as light.
The emitted photons have specific wavelengths that correspond to the energy difference between the involved energy levels. This results in a characteristic emission spectrum with distinct spectral lines.
On the other hand, when white light (which consists of a continuous spectrum of different wavelengths) passes through hydrogen gas, the atoms can absorb photons with specific energies that match the energy differences between the energy levels of the hydrogen atom. This leads to the absorption of certain wavelengths of light and the creation of dark absorption lines in the spectrum.
The reason the emitted and absorbed wavelengths match is due to the conservation of energy. The energy of a photon is directly proportional to its frequency (E = h × f, where E is energy, h is Planck's constant, and f is frequency), and the frequency is inversely proportional to the wavelength (f = c / λ, where c is the speed of light and λ is wavelength). Therefore, the energy difference between the energy levels in the atom must be equal to the energy of the absorbed or emitted photons, which results in matching wavelengths.
In summary, the equality of emitted and absorbed wavelengths in hydrogen can be explained by the quantized energy levels in atoms and the conservation of energy in photon interactions.
To learn more about absorption visit: https://brainly.com/question/30935871
#SPJ11
A pulley has an IMA of 13 and an AMA of 6. If the input of the pulley is pulled 13.9 m, how far will the output move?
______ m If the input of the pulley is pulled with a force of 2300 N, how much force will act at the output end of the pulley? ______N Calculate the % efficiency of the pulley.
If the input of the pulley is pulled with a force of 2300 N, the force will act at the output end of the pulley is 180.7 m .
The force acting at the output end of the pulley is 13800 N.
The % efficiency of the pulley is approximately 46.15%.
To solve this problem, we can use the formulas for the Ideal Mechanical Advantage (IMA), Actual Mechanical Advantage (AMA), and efficiency of a pulley system.
Given:
IMA = 13
AMA = 6
Input distance = 13.9 m
Input force = 2300 N
(a) To find the output distance, we can use the formula:
IMA = Output distance / Input distance
Rearranging the formula, we get:
Output distance = IMA * Input distance
Substituting the given values, we have:
Output distance = 13 * 13.9 = 180.7 m
Therefore, the output will move 180.7 m.
(b) To find the force at the output end, we can use the formula:
AMA = Output force / Input force
Rearranging the formula, we get:
Output force = AMA * Input force
Substituting the given values, we have:
Output force = 6 * 2300 = 13800 N
Therefore, the force acting at the output end of the pulley is 13800 N.
(c) To calculate the efficiency of the pulley, we can use the formula:
Efficiency = (AMA / IMA) * 100%
Substituting the given values, we have:
Efficiency = (6 / 13) * 100% ≈ 46.15%
Therefore, the % efficiency of the pulley is approximately 46.15%.
TO know more about Ideal Mechanical Advantage (IMA)
https://brainly.com/question/17457168
#SPJ11
A solenoid is 36.5 cm long, a radius of 6.26 cm, and has a total of 12,509 loops. a The inductance is H. (give answer to 3 sig figs) T
The inductance (H) of a solenoid with a length of 36.5 cm, radius of 6.26 cm, and 12,509 loops is to be calculated. The inductance of the solenoid is approximately 0.013 H.
To calculate the inductance of a solenoid, we can use the formula:
L = (μ₀ * n² * A) / l
Where L is the inductance, μ₀ is the permeability of free space (4π × 10^(-7) H/m), n is the number of turns per unit length (n = N/l, where N is the total number of loops and l is the length of the solenoid), A is the cross-sectional area of the solenoid (A = π * r², where r is the radius of the solenoid), and l is the length of the solenoid.
First, we calculate the number of turns per unit length:
n = N / l = 12,509 / 0.365 = 34,253.42 turns/m
Next, we calculate the cross-sectional area of the solenoid:
A = π * r² = 3.14159 * (0.0626)^2 = 0.01235 m²
Now, we can plug these values into the formula:
L = (4π × 10^(-7) H/m) * (34,253.42 turns/m)² * 0.01235 m² / 0.365 m ≈ 0.013 H (rounded to three significant figures)
Therefore, the inductance of the solenoid is approximately 0.013 H.
Learn more about solenoids here:
https://brainly.com/question/21842920
#SPJ11
Enhanced - with Hints and A vertical spring-block system with a period of 2.9 s and a mass of 0.39 kg is released 50 mm below its equilibrium position with an initial upward velocity of 0.13 m/s. Part A Determine the amplitude for this system. Express your answer with the appropriate units.
Determine the angular frequency w for this system. Express your answer in inverse second
Determine the energy for this system. Express your answer with the appropriate units
Determine the spring constant. Express your answer with the appropriate units.
Determine the initial phase of the sine function. Express your answer in radians.
Select the correct equation of motion.
Available Hint(s) x(t) = A sin(wt+pi), where the parameters A,w, di were determined in the previous parts. O (t) = A sin(kt + Pi), where the parameters A, k, di were determined in the previous parts. Ox(t) = A sin(fi – wt), where the parameters A, w, di were determined in the previous parts. o «(t) = A sin(di – kt), where the parameters A, k, di were determined in the previous parts.
(a) The amplitude for this system is 0.05 meters.(b) The angular frequency (w) for this system is approximately 4.32 radians per second. (c) The energy for this system is 0.0237 joules.(d) The spring constant for this system is approximately 6.09 N/m.(e) The initial phase of the sine function is 0 radians.
(a) The amplitude of a harmonic motion is the maximum displacement from the equilibrium position. Given that the system is released 50 mm below its equilibrium position, the amplitude is 0.05 meters.
(b) The angular frequency (w) of a harmonic motion can be calculated using the formula w = 2π / T, where T is the period. Substituting the given period of 2.9 seconds, we get w = 2π / 2.9 ≈ 4.32 radians per second.
(c) The energy of a harmonic motion is given by the formula E = (1/2)k[tex]A^2[/tex], where k is the spring constant and A is the amplitude. Substituting the given amplitude of 0.05 meters and the mass of 0.39 kg, we can use the relationship between the period and the spring constant to find k.
(d) The formula for the period of a mass-spring system is T = 2π√(m/k), where m is the mass and k is the spring constant. Rearranging the formula, we get k = (4π²m) / T². Substituting the given values, we find k ≈ (4π² * 0.39 kg) / (2.9 s)² ≈ 6.09 N/m.
(e) The initial phase of the sine function represents the initial displacement of the system. Since the system is released from below the equilibrium position, the initial displacement is zero, and thus the initial phase is 0 radians
Learn more about amplitude here :
https://brainly.com/question/9525052
#SPJ11
vires B and C. Find the force per unit length exerted on the following. (Express your answers in vector form.) (a) wire A f
A
= 1/m (b) wire B f
B
= N/m
The required force per unit length exerted on the wires are as follows: fA = (0 N/m, 5.03 × 10^-5 N/m, 0 N/m). fB = (0 N/m, 3.02 × 10^-4 N/m, 0 N/m)
Given, Charge per unit length on wire A = λA
Current in wire B = IB
Charge per unit length on wire C = λC
Finding the force per unit length exerted on the wires, A. Force per unit length on wire ABy using the formula for the force per unit length between two parallel wires, Force per unit length on wire A is given as, fA = μ₀/4π * (λA * IB) / dB.
Force per unit length on wire BBy using the formula for the force per unit length between two parallel wires, Force per unit length on wire B is given as,fB = μ₀/4π * (IB * λC) / dB.
Thus, the force per unit length exerted on wire A and wire B is given by the following expression.
fA = μ₀/4π * (λA * IB) / dB
fA = 4π × 10^-7 * (1 A/m * 2 A/m) / 0.05 m
fA = 5.03 × 10^-5 N/m
fA = (0 N/m, 5.03 × 10^-5 N/m, 0 N/m)
fB = μ₀/4π * (IB * λC) / d B
fB = 4π × 10^-7 * (2 A/m * 3 A/m) / 0.05 m
fB = 3.02 × 10^-4 N/m
fB = (0 N/m, 3.02 × 10^-4 N/m, 0 N/m)
Hence, the required force per unit length exerted on the wires are as follows: fA = (0 N/m, 5.03 × 10^-5 N/m, 0 N/m). fB = (0 N/m, 3.02 × 10^-4 N/m, 0 N/m)
Question: Wires B and C. Find the force per unit length exerted on the following. (Express your answers in vector form.)
(a) wire A [tex]f_{A}[/tex] = 1/m
(b) wire B [tex]f_{B}[/tex] = N/m
To learn about force here:
https://brainly.com/question/12785175
#SPJ11
Specify the coordinate system (Cartesian, cylindrical, spherical) you would use, along with any relevant assumptions, when modeling transport processes in each of the following scenarios: a. Energy loss through a flat double-pane window b. Produced fluid motion when coffee is stirred in a typical mug c. evaporation of beads of water from waterproof surfaces d. The transfer of dissolved oxygen from a culture medium into sphere-shaped cells e. Energy dissipation from the skin of a tall and skinny human f. Water evaporation of beads of water from waterproof surfaces g. heating of a cold bottle of alcoholic cider by a warm hand
a. Cartesian coordinate system would be appropriate to model energy loss through a flat double-pane window.
b. Cartesian coordinate system can be used to model the produced fluid motion when coffee is stirred in a typical mug.
c. Cartesian coordinate system would be suitable to model the evaporation of beads of water from waterproof surfaces.
d. Spherical coordinate system is appropriate to model the transfer of dissolved oxygen from a culture medium into sphere-shaped cells.
e. Cylindrical coordinate system would be suitable to model energy dissipation from the skin of a tall and skinny human.
f. Cartesian coordinate system can be used to model water evaporation of beads of water from waterproof surfaces.
g. Cartesian coordinate system would be appropriate to model the heating of a cold bottle of alcoholic cider by a warm hand.
a. For energy loss through a flat double-pane window, the Cartesian coordinate system is appropriate as it allows modeling in a 2D plane, where the window can be represented by a rectangular shape with x and y coordinates.
b. The produced fluid motion when coffee is stirred in a typical mug can also be modeled using the Cartesian coordinate system, as it allows capturing the 2D motion of the fluid within the mug.
c. The evaporation of beads of water from waterproof surfaces can be modeled using the Cartesian coordinate system, where the surface can be represented by a 2D plane, and the evaporation process can be analyzed in that plane.
d. The transfer of dissolved oxygen from a culture medium into sphere-shaped cells can be modeled using the spherical coordinate system, as it allows capturing the radial distance and angles associated with the transfer process.
e. Energy dissipation from the skin of a tall and skinny human can be modeled using the cylindrical coordinate system, as it allows analyzing the heat transfer in a cylindrical-shaped body, considering radial and height coordinates.
f. Water evaporation of beads of water from waterproof surfaces can be modeled using the Cartesian coordinate system, similar to scenario c, where the evaporation process is analyzed on a 2D plane.
g. The heating of a cold bottle of alcoholic cider by a warm hand can be modeled using the Cartesian coordinate system, as it allows analyzing the heat transfer in a 3D space, considering x, y, and z coordinates.
To know more about the Cartesian coordinate system click here:
https://brainly.com/question/4726772
#SPJ11
A soccer player kicks the ball toward a goal that is 30.0 m in front of him. The ball leaves his foot at a speed of 18.5 m/s and an angle of 31.0 ° above the ground. Find the speed of the ball when the goalie catches it in front of the net.
The speed of the ball when the goalie catches it would be equal to the horizontal component of the velocity, which is 15.93 m/s.
To find the speed of the ball when the goalie catches it, we first need to separate the initial velocity into its horizontal and vertical components. The horizontal component can be calculated using the equation [tex]V_x = V * cos(\theta)[/tex], where V is the initial velocity of 18.5 m/s and θ is the angle of 31.0°. Thus, [tex]V_x = 18.5 m/s * cos(31.0^0) = 15.93 m/s.[/tex]
The vertical component can be determined using the equation Vy = V * sin(θ), where Vy represents the vertical velocity. Hence, [tex]V_y = 18.5 m/s * sin(31.0^0) = 9.53 m/s.[/tex]
Since the ball is caught by the goalie in front of the net, its vertical velocity at that point would be zero. Therefore, we only need to consider the horizontal component of the velocity.
The speed of the ball when the goalie catches it would be equal to the horizontal component of the velocity, which is 15.93 m/s.
Learn more about projectile motion here.
https://brainly.com/question/12860905
#SPJ11
An old fashioned computer monitor accelerates electrons and directs them to the screen in order to create an image.
If the accelerating plates are 0.958 cmcm apart, and have a potential difference of 2.60×104 VV , what is the magnitude of the uniform electric field between them?
The magnitude of the uniform electric field between the accelerating plates is approximately 2.71 × [tex]10^6[/tex] V/m.
The magnitude of the uniform electric field between the accelerating plates can be determined using the formula E = V/d, where E is the electric field, V is the potential difference, and d is the distance between the plates.
In this case, the electric field magnitude is obtained by dividing the potential difference of 2.60×104 V by the plate separation distance of 0.958 cm.
The magnitude of the electric field (E) between the accelerating plates can be found using the formula E = V/d, where V is the potential difference between the plates and d is the distance between the plates.
In this case, the given potential difference is 2.60×104 V and the plate separation distance is 0.958 cm.
However, it is important to note that the distance should be converted to meters to ensure consistency with the SI units used for electric field.
Converting 0.958 cm to meters, we have:
d = 0.958 cm = 0.958 × 10^(-2) m
Now, we can substitute the values into the formula:
E = V/d = (2.60×104 V) / (0.958 × 10^(-2) m)
Simplifying the expression, we divide the numerator by the denominator:
E ≈ 2.71 × [tex]10^6[/tex] V/m
Therefore, the magnitude of the uniform electric field between the accelerating plates is approximately 2.71 × [tex]10^6[/tex] V/m.
Learn more about electric field here:
https://brainly.com/question/30544719
#SPJ11
What is the wavelength of a wave traveling with a speed of 3.0 m/s and the period of 6.0 s?
The wavelength of a wave with a 3.0 m/s speed and a 6.0 s period is 18.0 m.
To calculate the wavelength of a wave, we can use the wave equation:
v = λ / T
where v is the speed of the wave,
λ is the wavelength, and
T is the period.
Speed of the wave (v) = 3.0 m/s
Period (T) = 6.0 s
Substituting the given values into the wave equation:
3.0 m/s = λ / 6.0 s
To find the wavelength (λ), we can rearrange the equation:
λ = v * T
Substituting the given values:
λ = 3.0 m/s * 6.0 s
λ = 18.0 m
Therefore, the wavelength of the wave is 18.0 meters.
Learn more about wavelength here
https://brainly.com/question/16051869
#SPJ11
A 230 V DC shunt motor has an armature current of 3 33 A at the rated voltage and at a no-load speed of 1000 rpm The field and armature resistance are 160 and 0 3 0 respectively The supply current at full load and rated voltage is 40 A Draw the equivalent circuit of the motor with the power supply Calculate the full load speed if armature reaction weakens the no load flux by 6% 31 Equivalent circuit with variables and values (4) 32 No load emf (4) 33 Full load emf (2) 34 Full load speed (3)
The No load is given as 220V
The full load is 218V
The full-load speed of the motor is therefore approximately 1060rpm.
How to solve for the loads32) No load emf:
The armature current at no-load is 33A. Therefore, we can calculate the no-load emf using the formula provided above:
= 230V - 33A * 0.30Ω
= 220V
33) Full load emf:
The supply current at full load is 40A.:
= 230V - 40A * 0.30Ω
= 218V
34) Full load speed:
The speed ratio is increased by 6%.
Speed ratio = 220V / 218V * 1.06
= 1.06
Full load speed = 1000rpm * 1.06
= 1060rpm
The full-load speed of the motor is therefore approximately 1060rpm.
Read more on full load here https://brainly.com/question/26064065
#SPJ4
for a serial RLC circuit, let C = 50.0 pF, L = 25 mH and R = 8.0k Calculate the angular frequency of the circuit once the capacitor has been charged and connected to the other two elements of the circuit.
The angular frequency of the circuit, once the capacitor has been charged and connected to the other two elements, is approximately 892.47 rad/s.
The angular frequency (ω) of the serial RLC circuit, once the capacitor has been charged and connected to the other two elements of the circuit, can be calculated using the values of capacitance (C), inductance (L), and resistance (R).
The angular frequency (ω) of a serial RLC circuit is given by the formula:
ω = [tex]\frac{1}{\sqrt{LC} }[/tex]
In this case, the given values are:
C = 50.0 pF (picoFarads) = 50.0 × [tex]10^{-12}[/tex] F (Farads)
L = 25 mH (milliHenries) = 25 × [tex]10^{-3}[/tex] H (Henries)
Plugging these values into the formula, we can calculate the angular frequency as follows:
ω = 1 / √(50.0 × [tex]10^{-12}[/tex] F × 25 × [tex]10^{-3}[/tex] H)
= 1 / √(1250 × [tex]10^{-15}[/tex] F × H)
= 1 / √(1250 × [tex]10^{-15}[/tex] F × H)
= 1 / √(1.25 × [tex]10^{-12}[/tex] F × H)
= 1 / (1.118 × [tex]10^{-6}[/tex] F × H)
≈ 892.47 rad/s
Therefore, the angular frequency of the circuit, once the capacitor has been charged and connected to the other two elements, is approximately 892.47 rad/s.
Learn more about frequency here:
https://brainly.com/question/2140860
#SPJ11
A speedboat moves on a lake with initial velocity vector 1,x=9.15 m/s and 1,y=−2.09 m/s , then accelerates for 5.67 s at an average acceleration of av,x=−0.103 m/s2 and av,y=0.102 m/s2 . What are the components of the speedboat's final velocity, 2,x and 2,y ?
Find the speedboat's final speed.
The speedboat moves on a lake with an initial velocity vector of
1,x=9.15 m/s
and 1,y=−2.09 m/s
and accelerates for 5.67 s at an average acceleration of
av,x=−0.103 m/s2 and
av,y=0.102 m/s2. Now, we have to find the components of the speedboat's final velocity, 2,x and 2,y.
Let's determine the final velocity of the boat using the following formula:
Vf = Vi + a*t
where
Vf = final velocity
Vi = initial velocity
a = acceleration
t = time
To find 2x, we can use the formula:
2x = Vix + axtand to find 2y, we can use the formula:
2y = Viy + ayt
Substituting the given values into the above formula, we have;
For 2x, 2x = 9.15 + (-0.103 x 5.67) = 8.55 m/s (approximately)
For 2y, 2y = -2.09 + (0.102 x 5.67) = -1.47 m/s (approximately)
To find the final speed of the speedboat, we will use the formula:
Final velocity (v) = √(v_x² + v_y²)
Substituting the given values in the formula, we have;
Final velocity (v) = √(8.55² + (-1.47)²) = 8.64 m/s (approximately)
Therefore, the components of the speedboat's final velocity are 2,x = 8.55 m/s and 2,y = -1.47 m/s, and the
final speed of the boat is 8.64 m/s (approximately).
learn more about final velocity here
https://brainly.com/question/32863169
#SPJ11