The total charge stored in a parallel plate capacitance with circular faces, a diameter of 7.7 cm, and an air gap of 1.8 mm, charged with a 12.0 V emf, can be calculated.
The capacitance of a parallel plate capacitor is given by the equation C = ε₀A/d. In this case, the circular plates have a diameter of 7.7 cm, so the radius (r) is half of that, which is 3.85 cm or 0.0385 m. The area of each plate can be calculated using A = πr².
Once we have the capacitance, we can use the equation Q = CV to find the total charge stored in the capacitor. Here, Q represents the charge and V is the emf or voltage applied to the capacitor.
By substituting the values into the equation, calculate the total charge stored in the capacitor. Remember to consider the units of the given values and use consistent units throughout the calculations to obtain the correct numerical answer.
In conclusion, the total charge stored in the parallel plate capacitor can be determined by calculating the capacitance and using the equation Q = CV, where Q is the charge and V is the emf or voltage applied to the capacitor.
Learn more about capacitance here;
https://brainly.com/question/30529897
#SPJ11
Alkaline batteries have the advantage of putting out constant voltage until very nearly the end of their life. How long will an alkaline battery rated at 1.04 A⋅h and 1.4 V keep a 0.92 W flashlight bulb burning? _____________ hours
The alkaline battery rated at 1.04 A⋅h and 1.4 V will keep the 0.92 W flashlight bulb burning for about 0.996 hours.
Alkaline battery rated at 1.04 A⋅h and 1.4 V
Power required for flashlight bulb to burn = 0.92 W
Power is given by P = VI, where P is the power, V is the voltage, and I is the current.
Rearranging the above equation, we get I = P/V.
The current required for the flashlight bulb to burn is:
I = 0.92/1.4 = 0.657 A
The total charge in the battery is Q = It.
Charge is given in the unit of Coulombs (C).
1 A flows when 1 C of charge passes a point in 1 second.
Hence, 1 A flows when 3600 C of charge passes a point in 1 hour.
Therefore, 1 Coulomb = 1 A × 1 s
1 Ah = 1 A × 3600 s
So, 1 A⋅h = 3600 C
Charge in the battery Q = It = 0.657 A × (1.04 A ⋅ h) × (3600 s/h) = 2.36 × 10⁶ C
The time for which the battery will last is t = Q/I = (2.36 × 10⁶ C)/(0.657 A) = 3.59 × 10³ s
The time in hours is 3.59 × 10³ s/(3600 s/h) = 0.996 h
Therefore, the alkaline battery rated at 1.04 A⋅h and 1.4 V will keep the 0.92 W flashlight bulb burning for about 0.996 hours.
Learn more about battery: https://brainly.com/question/26466203
#SPJ11
A 2002 lamp and a 30 02 lamp are connected in series with a 10 V battery. Calculate the following: the voltage drop across the 20 2 lamp Question 20 1 pts A 2002 lamp and a 30 02 lamp are connected in series with a 10 V battery. Calculate the following: the voltage drop across the 300 lamp
The voltage drop across the 20 2 lamp is approximately 3.32 V, and the voltage drop across the 300 lamp is approximately 6.68 V.
When two lamps are connected in series, they share the same current. The voltage drop across the two lamps is proportional to their resistance, which can be calculated using Ohm's Law. We can use the equation:V = IR,where V is voltage, I is current, and R is resistance. Given that the two lamps are connected in series with a 10 V battery, we know that the voltage drop across the two lamps will be 10 V. We can use this information to find the resistance of the two lamps combined.
Using Ohm's Law:10 V = I(R1 + R2),where R1 and R2 are the resistances of the two lamps, and I is the current flowing through the circuit. Since the two lamps share the same current, we can say that I is the same for both lamps. Therefore, we can rewrite the equation as:10 V = I(R1 + R2)orI = 10 / (R1 + R2)To find the voltage drop across each lamp, we can use the equation:V = IR. For the 2002 lamp, we know that R1 = 2002 Ω. For the 30 02 lamp, we know that R2 = 3002 Ω. We can substitute these values into the equation:V1 = IR1V1 = (10 / (2002 + 3002)) * 2002V1 ≈ 3.32 VFor the 300 lamp, we can use the same equation:V2 = IR2V2 = (10 / (2002 + 3002)) * 3002V2 ≈ 6.68 VTherefore, the voltage drop across the 20 2 lamp is approximately 3.32 V, and the voltage drop across the 300 lamp is approximately 6.68 V.
Learn more about Equation here,What is equation? Define equation
https://brainly.com/question/29174899
#SPJ11
A diagram of UML Charts for an application that can be used to
estimate the SNR of a typical earth-satellite communication
system?
Use Case Diagram: User: Represents the user interacting with the application.
Here is a possible diagram using UML (Unified Modeling Language) to represent the different components of an application for estimating the Signal-to-Noise Ratio (SNR) of an earth-satellite communication system:
Use Case Diagram:
User: Represents the user interacting with the application.
Estimate SNR: Use case that describes the main functionality of the application.
Class Diagram:
SNREstimationApp: Represents the main application class.
Satellite: Represents the satellite in the communication system.
EarthStation: Represents the earth station in the communication system.
Sequence Diagram:
User →SNREstimationApp: Triggers the SNR estimation process.
SNREstimationApp → Satellite: Requests information from the satellite.
Satellite → SNREstimationApp: Provides satellite-specific data.
SNREstimationApp → EarthStation: Requests information from the earth station.
EarthStation → SNREstimationApp: Provides earth station-specific data.
SNREstimationApp → CalculationEngine: Performs SNR calculation using the provided data.
CalculationEngine → SNREstimationApp: Returns the calculated SNR value.
SNREstimationApp → User: Presents the SNR value to the user.
Component Diagram:
SNREstimation App: Represents the main component of the application.
Satellite API: Represents the interface or API for retrieving satellite information.
EarthStation API: Represents the interface or API for retrieving earth station information.
Calculation Engine: Represents the component responsible for performing the SNR calculation.
To know more about Class Diagram:
https://brainly.com/question/32075946
#SPJ4
A point charge q=-4.3 nC is located at the origin. Find the magnitude of the electric field at the field point x=9 mm, y=3.2 mm.
Solving this equation gives us |E| = 3.89 × 10⁴ N/C. Hence, the magnitude of the electric field at the field point x = 9 mm, y = 3.2 mm is 3.89 × 10⁴ N/C.
We know that the electric field intensity is the force experienced by a unit positive charge placed at a point in an electric field. So, the magnitude of the electric field at a point P at a distance r from a point charge q is given by,|E| = kq/r²
Where,k = Coulomb's constant = 9 × 10⁹ Nm²/C²q = charge of the point chargerr = distance of the field point from the point chargeSo, the distance of the field point from the point charge is given by,r² = x² + y² = (9 mm)² + (3.2 mm)²r² = 81 + 10.24 = 91.24 mm²r = √(91.24) = 9.55 mmNow, substituting the given values in the formula for electric field,|E| = k|q|/r² = (9 × 10⁹) × (4.3 × 10⁻⁹) / (9.55 × 10⁻³)²|E| = 3.89 × 10⁴ N/C
Therefore, the magnitude of the electric field at the field point x = 9 mm, y = 3.2 mm is 3.89 × 10⁴ N/C. This can be written in 150 words as follows:The magnitude of the electric field at the field point x = 9 mm, y = 3.2 mm can be determined by the formula |E| = k|q|/r². Using the values provided in the question,
we can first find the distance of the field point from the point charge which is given by r² = x² + y². Substituting the values of x and y in this equation, we get r = √(91.24) = 9.55 mm. Next, we can substitute the values of k, q and r in the formula for electric field intensity which is given by |E| = kq/r². Substituting the given values, we get |E| = (9 × 10⁹) × (4.3 × 10⁻⁹) / (9.55 × 10⁻³)².
Solving this equation gives us |E| = 3.89 × 10⁴ N/C. Hence, the magnitude of the electric field at the field point x = 9 mm, y = 3.2 mm is 3.89 × 10⁴ N/C.
to know more about magnitude
https://brainly.com/question/31805774
#SPJ11
A ball is thrown at a wall with a velocity of 12 m/s and rebounds with a velocity of 8 m/s. The ball was in contact with the wall for 35 ms. Determine: the mass of the ball, if the change in momentum was 7.2 kgm/s (3) the average force exerted on the ball (
The mass of the ball is 0.36 kg and the average force exerted on the ball is approximately 205.71 Newtons.
To determine the mass of the ball, we can use the formula for change in momentum:
Change in momentum = mass * change in velocity
Given that the change in momentum is 7.2 kgm/s and the change in velocity is from 12 m/s to -8 m/s (taking the negative sign for the opposite direction), we can write the equation as:
7.2 kgm/s = mass * (8 m/s - (-12 m/s))
Simplifying the equation:
7.2 kgm/s = mass * 20 m/s
Dividing both sides by 20 m/s:
mass = 7.2 kgm/s / 20 m/s
mass = 0.36 kg
Therefore, the mass of the ball is 0.36 kg.
To determine the average force exerted on the ball, we can use the formula:
Average force = Change in momentum / Time
Given that the change in momentum is 7.2 kgm/s and the time of contact is 35 ms (converting to seconds: 35 ms = 0.035 s), we can calculate the average force:
Average force = 7.2 kgm/s / 0.035 s
Average force ≈ 205.71 N
Therefore, the average force exerted on the ball is approximately 205.71 Newtons.
Learn more about momentum
https://brainly.com/question/20998223
#SPJ11
A proton moving perpendicular to a magnetic field of 9.80 μT follows a circular path of radius 4.95 cm. What is the proton's speed? in m/s.
(uses above question) If the magnetic field is pointed into the page and the proton is moving to the left when it enters the region of the magnetic field, the proton goes in what direction as viewed from above?
Clockwise
Counterclockwise
Down the page
Up the page
The speed of the proton is approximately 2.29 x 10^6 m/s.
Regarding the direction of motion as viewed from above, the proton will move counterclockwise in the circular path.
To calculate the proton's speed, we can use the formula for the centripetal force acting on a charged particle moving in a magnetic field:
F = qvB
where F is the centripetal force, q is the charge of the proton, v is its velocity, and B is the magnetic field strength.
In this case, the centripetal force is provided by the magnetic force, so we can equate the two:
qvB = mv²/r
where m is the mass of the proton and r is the radius of the circular path.
Solving for v, we get:
v = (qB*r) / m
The values:
q = charge of a proton = 1.6 x 10^-19 C (Coulombs)
B = magnetic field strength = 9.80 μT = 9.80 x 10^-6 T (Tesla)
r = radius of the circular path = 4.95 cm = 4.95 x 10^-2 m
m = mass of a proton = 1.67 x 10^-27 kg
Substituting the values into the formula, we can calculate the speed:
v = (1.6 x 10^-19 C * 9.80 x 10^-6 T * 4.95 x 10^-2 m) / (1.67 x 10^-27 kg) = 2.29 x 10^6 m/s.
To know more about proton
https://brainly.com/question/29248303
#SPJ11
A series RL circuit includes a 2.05 V battery, a resistance of R=0.555Ω, and an inductance of L=2.63H. What is the induced emf1.68 s after the circuit has been closed? induced emf:
The value of induced emf 1.68 seconds after the circuit is closed is approximately equal to 0.522 V.
The voltage, `V` across a series RL circuit, at any given time is given by `V = IR + L (di/dt)
If a 2.05 V battery is connected to a series RL circuit, a resistance of R = 0.555 Ω and an inductance of L = 2.63 H is present. To determine the induced emf 1.68 s after the circuit is closed, the current flowing through the circuit is required.
The current flow is determined by using Ohm's Law:V = IR
Let us determine the current flowing through the circuit by using Ohm's Law: V = IR => I = V/R = 2.05/0.555 = 3.69
A`The voltage drop across the inductor is given by `L (di/dt)`; where `i` is the current flowing through the circuit. The current flowing through the circuit can be represented by the following expression:
i = I (1 - [tex]e^{-Rt/L}[/tex]).
Using the expression for current, we get di/dt = R/L I ( [tex]e^{-Rt/L}[/tex]).
The voltage across the inductor, at any given time t after the circuit is closed, is therefore given by:`
VL = L (di/dt) = L (R/L I ( [tex]e^{-Rt/L}[/tex]).
Substituting the values, we have: VL = 2.63 (0.555/2.63) * 3.69 * [tex]e^{-0.555*1.68/2.63}[/tex]
The value of induced emf 1.68 seconds after the circuit is closed is approximately equal to 0.522 V.
To learn about induced emf here:
https://brainly.com/question/13744192
#SPJ11
What happens to a circuit's resistance (R), voltage (V), and current (1) when
you change the thickness of the wire in the circuit?
A. V and I will also change, but R will remain constant.
B. R and I will also change, but V will remain constant.
O C. R, V, and I will all remain constant.
OD. R and V will also change, but I will remain constant.
When you change the thickness of the wire in a circuit, option B. the resistance (R) and current (I) will also change, but the voltage (V) will remain constant.
The resistance of a wire is directly proportional to its length and inversely proportional to its cross-sectional area (thickness). As the thickness of the wire changes, the cross-sectional area changes, which in turn affects the resistance. Thicker wires have a larger cross-sectional area, resulting in lower resistance, while thinner wires have a smaller cross-sectional area, resulting in higher resistance. Therefore, changing the thickness of the wire will cause a change in resistance.
According to Ohm's Law (V = IR), the voltage (V) in a circuit is equal to the product of the current (I) and the resistance (R). If the voltage is kept constant, and the resistance changes due to the thickness of the wire, the current will also change to maintain the relationship defined by Ohm's Law. When the resistance increases, the current decreases, and vice versa.
However, it's important to note that changing the thickness of the wire will not directly affect the voltage. The voltage in a circuit is determined by the power source or the potential difference applied across the circuit and is independent of the wire thickness. As long as the voltage source remains constant, the voltage across the circuit will remain constant regardless of the wire thickness. Therefore, the correct answer is option B.
know more about current here:
https://brainly.com/question/1100341
#SPJ8
An electron is accelerated from rest by a potential difference of 350 V. It than enters a uniform magnetic field of magnitude 200 mT with its velocity perpendicular to the field. Calculate (a) the speed of the electron and (b) the radius of its path in the magnetic field. * (2 Points) O 7.11 x 10^7 m/s, 3.16 x 10^-4 m 5.11 x 10^7 m/s, 6.16 x 10^-4 m 1.11 x 10^7 m/s, 3.16 x 10^-4 m O 3.11 x 10^7 m/s, 3.16 x 10^-4 m O 1.11 x 10^7 m/s, 6.16 x 10^-4 m
Substituting the values, we getr = [(9.11 × 10⁻³¹ kg)(1.11 × 10⁷ m/s)]/[(1.6 × 10⁻¹⁹ C)(200 mT)]r = 3.16 × 10⁻⁴ mTherefore, the answer is 1.11 x 10^7 m/s, 3.16 x 10^-4 m.
(a) Speed of the electronThe formula for potential energy isPE = qVWhere q is the charge and V is the potential difference. The electron is negatively charged, and its charge is 1.6 × 10⁻¹⁹ C.Therefore, PE = (1.6 × 10⁻¹⁹ C)(350 V)PE = 5.6 × 10⁻¹⁷ JThe formula for kinetic energy isKE = (1/2)mv²where m is the mass and v is the velocity of the electron. The mass of the electron is 9.11 × 10⁻³¹ kg.Using the law of conservation of energy, we can equate the kinetic energy of the electron with the potential energy it gains when accelerated by the potential difference.
Kinetic energy of the electron = Potential energy gainedKE = PEKE = 5.6 × 10⁻¹⁷ Jv² = (2KE)/mv² = (2(5.6 × 10⁻¹⁷ J))/(9.11 × 10⁻³¹ kg)v² = 1.23 × 10¹⁷v = √(1.23 × 10¹⁷)v = 1.11 × 10⁷ m/s(b) Radius of the pathThe formula for the radius of the path of a charged particle moving in a magnetic field isr = (mv)/(qB)where r is the radius, m is the mass of the charged particle, v is its velocity, q is its charge, and B is the magnetic field strength.Substituting the values, we getr = [(9.11 × 10⁻³¹ kg)(1.11 × 10⁷ m/s)]/[(1.6 × 10⁻¹⁹ C)(200 mT)]r = 3.16 × 10⁻⁴ mTherefore, the answer is 1.11 x 10^7 m/s, 3.16 x 10^-4 m.
Learn more about Velocity here,
https://brainly.com/question/80295
#SPJ11
Tell us on what basis we select following for
measuring flow rates
a) Pitot Tube
b) Orifice meter
c) Venturi meter
d) Rotameter
The selection of the following devices for measuring flow rates are based on the following factors: a) Pitot Tube: The Pitot tube is a device used to measure the flow velocity of fluids. It is used to measure the velocity of air or other gases flowing in a pipe.
The selection of a pitot tube is based on the following factors: Pipe size Accuracy of measurement Required flow range Fluid properties b) Orifice meter: An orifice meter is a device used to measure the flow rate of a fluid. The selection of an orifice meter is based on the following factors: Pipe size Accuracy of measurement Fluid properties Cost. c) Venturi meter: A Venturi meter is a device used to measure the flow rate of a fluid. The selection of a Venturi meter is based on the following factors: Pipe size Accuracy of measurement Fluid properties Cost. d) Rotameter: A rotameter is a device used to measure the flow rate of a fluid. The selection of a rotameter is based on the following factors: Pipe size. Accuracy of measurement Fluid properties Cost.
To know more about pressure visit:
https://brainly.com/question/31555867
#SPJ11
An LC circuit is comprised of a capacitor with 10.0 mF and initial charge of 1.5 C, and inductor with L = 6.2 H.
a) What is the angular frequency of oscillation?
b) Assuming a phase of 0, what is the current at t = 3.0 s?
c) Now assume the circuit has resistance 45Ω. What is the angular frequency of the oscillation of charge?
d) What is the current in this circuit after 3.0 s assuming a phase of zero? Compare this to your answer to part b).
e) If this circuit instead had an AC voltage source with a maximum voltage of 40V and a frequency of 120Hz, what would the impedance of the circuit be? What is the RMS voltage?
The angular frequency of oscillation is 5.06 rad/s. the current at t = 3.0 s is 0.71 A. The angular frequency of the oscillation of charge is 5.05 rad/s. the current in this circuit after 3.0 s assuming a phase of zero is 0.68 A. The impedance of the circuit is 45.09Ω and the RMS voltage is 28.28V.
a) The angular frequency (ω) of the LC circuit can be calculated using the formula ω = 1 / sqrt(LC). Plugging in the values,[tex]\omega = 1 / \sqrt((6.2 H)(10.0 mF)) = 5.06 rad/s[/tex].
b) To find the current (I) at t = 3.0 s with a phase of 0, we can use the equation[tex]I = (Q_0 / C) * cos(\omega t)[/tex]. Substituting the given values, [tex]I = (1.5 C / 10.0 mF) * cos(5.06 rad/s * 3.0 s) = 0.71 A[/tex].
c) Considering the circuit has a resistance of 45Ω, the angular frequency (ω') of the oscillation of charge can be determined using the formula [tex]\omega' = \sqrt((1 / LC) - (R^2 / (4L^2)))[/tex]. Substituting the given values, [tex]\pmega' = \sqrt((1 / ((10.0 mF)(6.2 H))) - ((45[/tex]Ω[tex])^2 / (4(6.2 H)^2))) = 5.05 rad/s.[/tex]
d) The current in the circuit after 3.0 s with a phase of zero can be calculated using the same equation as part b. Substituting the values, I' = (1.5 C / 10.0 mF) * cos(5.05 rad/s * 3.0 s) = 0.68 A. This can be compared to the previous answer to assess the impact of resistance.
e) If the circuit had an AC voltage source with a maximum voltage of 40V and a frequency of 120Hz, the impedance (Z) can be determined using the formula [tex]Z = \sqrt(R^2 + (\omega L - 1 / (\omega C))^2)[/tex]. Substituting the given values, [tex]Z = \sqrt((45[/tex]Ω[tex])^2[/tex] [tex]+ ((2\pi(120Hz)(6.2 H)) - 1 / (2\pi(120Hz)(10.0 mF)))^2) = 45.09[/tex]Ω. The RMS voltage can be calculated as [tex]V_{RMS} = (V_{max}) / \sqrt(2) = 40V / \sqrt(2) = 28.28V.[/tex]
Learn more about angular frequency here:
https://brainly.com/question/32670038
#SPJ11
Alex Morgan is going to kick a soccer ball into the goal during the 2019 World Cup. Alex kicks the ball straight at the goal from 50.0 m away. Assume the goalie is busy faking an injury and doesn't try to stop the ball, and ignore air resistance. A. (5 points) Suppose that Alex kicks the ball with an initial speed of 19.7 m/s. What angle would she have to kick the ball so that it just makes it to the goal without touching the ground? B. (4 points) The top of the goal is 2.44 m off of the ground. Suppose instead that she kicked the ball at an initial angle of 40.0°. With what initial speed should she kick the ball in order to hit the top of the goal?
A. Alex Morgan would need to kick the ball at an angle of approximately 29.5 degrees.
B. Alex Morgan should kick the ball with an initial speed of approximately 16.5 m/s to hit the top of the goal when kicked at an angle of 40.0 degrees.
A. To determine the angle at which Alex Morgan needs to kick the ball so that it just reaches the goal without touching the ground, we can use the equations of projectile motion. We'll assume the goal is at the same height as the ground.
To find the angle of projection (θ), we can use the equation for the horizontal range of a projectile:
Range = [tex](v0^2 * sin(2\theta)) / g[/tex]
Since we want the ball to just reach the goal without touching the ground, the range should be equal to the initial distance from the goal:
50.0 m = [tex](19.7^2 * sin(2\theta)) / 9.8[/tex]
Now, we can solve this equation to find the angle θ:
sin(2θ) =[tex](50.0 m * 9.8) / (19.7 m/s)^2[/tex]
sin(2θ) = 0.4987
2θ = arcsin(0.4987)
θ ≈ 29.5 degrees
B. Now, let's determine the initial speed at which Alex Morgan should kick the ball at an angle of 40.0 degrees to hit the top of the goal.
Given:
Initial angle of projection (θ) = 40.0 degrees
Height of the top of the goal (y) = 2.44 m
Acceleration due to gravity (g) = [tex]9.8 m/s^2[/tex]
To find the initial speed (v0), we can use the equation for the maximum height of a projectile:
Maximum height =[tex](v0^2 * sin^2(\theta)) / (2g)[/tex]
Since we want the ball to reach the top of the goal, the maximum height should be equal to the height of the top of the goal:
2.44 m =[tex](v0^2 * sin^2(40.0 degrees)) / (2 * 9.8 m/s^2)[/tex]
Now, we can solve this equation to find the initial speed v0:
[tex]v0^2 = (2 * 9.8 m/s^2 * 2.44 m) / sin^2(40.0 degrees)[/tex]
v0 ≈ 16.5 m/s
To know more about initial speed, here
brainly.com/question/28060745
#SPJ4
Solve numerically for the thermal efficiency, η, assuming that T h
=910 ∘
C and T c
=580 ∘
C. Numeric : A numeric value is expected and not an expression. η= =1− 1183.15K
331.15K
=.72011=7 Problem 5: Suppose you want to operate an ideal refrigerator that has a cold temperature of −10.5 ∘
C, and you would like it to have a coefficient of performance of 5.5. What is the temperature, in degrees Celsius, of the hot reservoir for such a refrigerator? Numeric : A numeric value is expected and not an expression. T h
=
Therefore, the numeric value is 339.1.
Given, the hot and cold temperatures of the refrigerator, respectively are Th = 910 °C and Tc = 580 °C. We are supposed to solve numerically for the thermal efficiency η.
Formula to calculate the efficiency of the heat engine is given by:η=1- (Tc/Th)η = 1 - (580 + 273.15) / (910 + 273.15)η = 0.72011Hence, the thermal efficiency η is 0.72011. The numeric value is given as 0.72011. Therefore, the numeric value is 0.72011.
Now, let's solve the second problem.Problem 5:Suppose you want to operate an ideal refrigerator that has a cold temperature of -10.5°C, and you would like it to have a coefficient of performance of 5.5. What is the temperature, in degrees Celsius,
of the hot reservoir for such a refrigerator?
The formula to calculate the coefficient of performance of a refrigerator is given by:K = Tc / (Th - Tc)The desired coefficient of performance of the refrigerator is given as 5.5. We are supposed to calculate the hot temperature, i.e., Th.
Thus, we can rearrange the above formula and calculate Th as follows:Th = Tc / (K - 1) + TcTh = (-10.5 + 273.15) / (5.5 - 1) + (-10.5 + 273.15)Th = 325.85 / 4.5 + 262.65 = 339.1 °CHence, the temperature of the hot reservoir for such a refrigerator is 339.1 °C.
The numeric value is given as 339.1.
to know more about thermal efficiency
https://brainly.com/question/13982702
#SPJ11
At some instant the velocity components of an electron moving between two charged parallel plates are v x
=1.6×10 5
m/s and v y
=3.5×10 3
m/s. Suppose the electric field between the plates is uniform and given by E
=(120 N/C) j
^
. In unit-vector notation, what are (a) the electron's acceleration in that field and (b) the electron's velocity when its x coordinate has changed by 2.4 cm ?
Therefore, we have vy = vy,0 + ayt = (3.5 x 10^3 m/s) + (7.21 x 10^17 m/s^2)(1.5 x 10^-7 s) = 3.508 m/s. Thus, the electron's velocity when its x-coordinate has changed by 2.4 cm is v = (1.6 x 10^5 m/s)i + 3.508 m/sj. The required answer in unit-vector notation is v = (1.6 x 10^5 m/s)i + 3.508 m/sj. The solution has been presented in more than 150 words.
(a) To find the acceleration of the electron in the given electric field, we will use the formula F = ma, where F is the force acting on the electron, m is its mass, and a is its acceleration. The force acting on the electron due to the electric field is given by F = qE, where q is the charge of the electron and E is the electric field. Therefore,
we have F = (1.6 x 10^-19 C)(120 N/C)j = 1.92 x 10^-17 Nj.Using Newton's second law, F = ma, we can find the acceleration of the electron as a = F/m = (1.92 x 10^-17 Nj)/(9.11 x 10^-31 kg) = 2.1electron's1 x 10^13 m/s^2. Therefore, the electron's acceleration in the given electric field is a = 2.11 x 10^13 j m/s^2.
(b) To find the electron's velocity when its x-coordinate changes by 2.4 cm, we will first find the time taken by the electron to move this distance. The x-component of the electron's velocity is given as vx = 1.6 x 10^5 m/s, so we have x = vxt => t = x/vx = (2.4 x 10^-2 m)/(1.6 x 10^5 m/s) = 1.5 x 10^-7 s.
The acceleration of the electron in the y-direction is given by ay = Fy/m = (qEy)/m = (1.6 x 10^-19 C)(3.5 x 10^3 m/s)(120 N/C)/(9.11 x 10^-31 kg) = 7.21 x 10^17 m/s^2. Since the acceleration is constant, we can use the kinematic equation vy = u + at, where u is the initial velocity in the y-direction, to find the final velocity of the electron in the y-direction. The initial velocity vy,0 in the y-direction is given as vy,0 = 3.5 x 10^3 m/s, and the time t is 1.5 x 10^-7 s.
Therefore, we have vy = vy,0 + ayt = (3.5 x 10^3 m/s) + (7.21 x 10^17 m/s^2)(1.5 x 10^-7 s) = 3.508 m/s. Thus, the electron's velocity when its x-coordinate has changed by 2.4 cm is v = (1.6 x 10^5 m/s)i + 3.508 m/sj. The required answer in unit-vector notation is v = (1.6 x 10^5 m/s)i + 3.508 m/sj. The solution has been presented in more than 150 words.
to know more about electron
https://brainly.com/question/14388606
#SPJ11
Find the range in wavelengths (in vacuum) for visible light in the frequency range between 7.9 × 10¹⁴ Hz (violet light) Express the answers in nanometers. (Express your answer in whole number)
The range in wavelengths (in vacuum) for visible light in the frequency range between 7.9 × 10¹⁴ Hz (violet light) is 380 nm (approx).
The formula is given as:
frequency = (speed of light) / (wavelength)
Where:
frequency = 7.9 x 10¹⁴ Hz
speed of light = 3 x 10⁸ m/s (in vacuum)
Solving for wavelength:
wavelength = (speed of light) / (frequency)
Therefore, wavelength = (3 x 10⁸) / (7.9 x 10¹⁴) = 3.80 x 10⁻⁷ m or 380 nm (approx)
Hence, the range in wavelengths (in vacuum) for visible light in the frequency range between 7.9 × 10¹⁴ Hz (violet light) is 380 nm (approx).
Learn more about frequency: https://brainly.com/question/254161
#SPJ11
Consider the signal r(t) = w(t) sin (27 ft) where f = 100 kHz and t is in units of seconds. (a) (5 points) For each of the following choices of w(t), explain whether or not it would make x (t) a narrowband signal. Justify your answer for each of the four choices; no marks awarded without valid justification. 1. w(t) = cos(2πt) 2. w(t) = cos(2πt) + sin(275t) 3. w(t) = cos(2π(f/2)t) where f is as above (100 kHz) 4. w(t) = cos(2π ft) where f is as above (100 kHz) (b) (5 points) The signal x(t), which henceforth is assumed to be narrowband, passes through an all- pass system with delays as follows: 3 ms group delay and 5 ms phase delay at 1 Hz; 4 ms group delay and 4 ms phase delay at 5 Hz; 5 ms group delay and 3 ms phase delay at 50 kHz; and 1 ms group delay and 2 ms phase delay at 100 kHz. What can we deduce about the output? Write down as best you can what the output y(t) will equal. Justify your answer; no marks awarded without valid justification. (c) (5 points) Assume r(t) is narrowband, and you have an ideal filter (with a single pass region and a single stop region and a sharp transition region) which passes w(t) but blocks sin(27 ft). (Specifically, if w(t) goes into the filter then w(t) comes out, while if sin (27 ft) goes in then 0 comes out. Moreover, the transition region is far from the frequency regions occupied by both w(t) and sin(27 ft).) What would the output of the filter be if x(t) were fed into it? Justify your answer; no marks awarded without valid justification.
(a) The signal r(t) can be written as:
1. r(t) = cos(2πt) sin (2π ft). This signal is narrowband.
2. r(t) = [cos(2πt) + sin(275t)] sin (2π ft). This signal is not narrowband.
3. r(t) = cos(2π(f/2)t) sin (2π ft). This signal is narrowband.
4. r(t) = cos(2π ft) sin (2π ft). This signal is not narrowband.
(b) The all-pass system is a linear system that does not change the amplitude spectrum of the input signal. It only changes the phase spectrum of the signal.
(c) only w(t) will be passed through the filter.
(a) The signal r(t) can be written as:
r(t) = w(t) sin (2π ft)
where f = 100 kHz and t is in seconds.
1. w(t) = cos(2πt)We can write r(t) as:
r(t) = cos(2πt) sin (2π ft)
This signal is narrowband.
2. w(t) = cos(2πt) + sin(275t)
We can write r(t) as:
r(t) = [cos(2πt) + sin(275t)] sin (2π ft)
This signal is not narrowband. It has a frequency component at 275 Hz which is much larger than the bandwidth of the signal which is 200 Hz.
3. w(t) = cos(2π(f/2)t) where f = 100 kHz
We can write r(t) as:
r(t) = cos(2π(f/2)t) sin (2π ft)
This signal is narrowband.
4. w(t) = cos(2π ft) where f = 100 kHz
We can write r(t) as:
r(t) = cos(2π ft) sin (2π ft)
This signal is not narrowband. It has a frequency component at 2f = 200 kHz which is much larger than the bandwidth of the signal which is 200 Hz.
(b) The all-pass system is a linear system that does not change the amplitude spectrum of the input signal. It only changes the phase spectrum of the signal.
Therefore, if the input signal is narrowband, then the output signal will also be narrowband. Moreover, the group delay of the system is the derivative of the phase with respect to frequency.
Therefore, the group delay of the system is smaller at higher frequencies. This means that the high-frequency components of the signal will be delayed less than the low-frequency components.
The phase delay of the system is also smaller at higher frequencies. This means that the high-frequency components of the signal will be shifted less than the low-frequency components.
Therefore, the output signal will be a delayed and phase-shifted version of the input signal. The exact form of the output signal cannot be determined without knowing the form of the input signal.
(c) The filter passes w(t) and blocks sin(2π ft). Therefore, the output of the filter will be w(t) if x(t) = r(t) is fed into it.
This is because r(t) is of the form w(t) sin(2π ft), and the filter blocks sin(2π ft).
Therefore, only w(t) will be passed through the filter.
Learn more about narrowband here:
https://brainly.com/question/29920900
#SPJ11
What is the capacitance of a parallel plate capacitor with plates that have an area of 3.97 m’ and are separated by a distance of 0.066 mm (in vacuum, use K 1)? Remember that co 8.25 x 10 12 c²/Nm² *Provide exponential answers in the format. EU (CE 1.85 x 10-12 8.85E-12)
The capacitance of a parallel plate capacitor with plates having an area of 3.97 m² and separated by a distance of 0.066 mm (in vacuum) is approximately [tex]1.85\times10^{-12}\ \text{F}[/tex]
The capacitance of a parallel plate capacitor is given by the formula [tex]C = (\varepsilon_0A) / d[/tex], where C represents capacitance, ε₀ represents the permittivity of free space, A represents the area of the plates, and d represents the distance between the plates.
Given values:
A = 3.97 m² (plate area)
d = 0.066 mm =[tex]0.066\times10^{-3}\ \text{m}[/tex] (plate separation in meters)
ε₀ =[tex]8.85 \times 10^{-12}\ \text{C}^{2}/\text{N}\text{m}^{2}[/tex] (permittivity of free space)
Substituting these values into the capacitance formula, we get:
C = (ε₀A) / d = [tex](8.85 \times 10^{-12}\times3.97 ) / 0.066 \times 10^{-3}[/tex]
Simplifying this expression, we have:
C = [tex]35.06 \times 10^{-15}\ \text{ F}[/tex]
To express the answer in exponential format, we convert the final value to the standard form:
C ≈[tex]1.85\times10^{-12}\ \text{F}[/tex]
Learn more about capacitance here:
https://brainly.com/question/31871398
#SPJ11
A loop of wire with a diameter of 20 cm is located in a uniform magnetic field. The loop is perpendicular to the field. The field has a strength of 2.0 T. If the loop is removed completely from the field in 1.75 ms, what is the average induced emf? If the loop is connected to a 150 kohm resistor what is the current in the resistor?
Answer: The current in the resistor is 0.00024 A.
The average induced emf can be determined by Faraday's law of electromagnetic induction which states that the emf induced in a loop of wire is proportional to the rate of change of the magnetic flux passing through the loop.
Mathematically: ε = -N(ΔΦ/Δt)
where,ε is the induced emf, N is the number of turns in the loop, ΔΦ is the change in the magnetic flux, Δt is the time interval.
The magnetic flux is given as,Φ = BA
where, B is the magnetic field strength, A is the area of the loop.
Since the loop has been completely removed from the field, the change in magnetic flux (ΔΦ) is given by,ΔΦ = BA final - BA initial. Where,
BA initial = πr²
B = π(0.1m)²(2.0 T)
= 0.0628 Wb.
BA final = 0 Wb (As the loop has been removed completely from the field).
Therefore,ΔΦ = BA final - BA initial
= 0 - 0.0628
= -0.0628 Wb.
Since the time interval is given as Δt = 1.75 ms
= 1.75 × 10⁻³ s, the induced emf can be calculated as,
ε = -N(ΔΦ/Δt)
= -N × (-0.0628/1.75 × 10⁻³)
= 35.94 N.
The average induced emf is 35.94 V (approx).
Now, if the loop is connected to a 150 kΩ resistor, the current in the resistor can be determined using Ohm's law, which states that the current passing through a conductor between two points is directly proportional to the voltage across the two points and inversely proportional to the resistance between them. Mathematically, it can be represented as,
I = V/R Where, I is the current flowing through the resistor V is the voltage across the resistor R is the resistance of the resistor. From the above discussion, we know that the induced emf across the loop of wire is 35.94 V, and the resistor is 150 kΩ = 150 × 10³ Ω
Therefore, I = V/R
= 35.94/150 × 10³
= 0.00024 A.
The current in the resistor is 0.00024 A.
Learn more about Ohm's law : https://brainly.com/question/14296509
#SPJ11
What is the total energy of an electron moving with a speed of 0.74c, (in keV )?
The total energy of an electron moving at a speed of 0.74c is approximately 250 keV. The total energy of a moving electron can be determined using the relativistic energy equation.
The relativistic energy equation states that the total energy (E) of an object moving with a relativistic speed can be calculated using the equation:
[tex]E = (\gamma - 1)mc^2[/tex]
where γ (gamma) is the Lorentz factor given by:
[tex]\gamma = 1/\sqrt(1 - v^2/c^2)[/tex]
In this case, the electron is moving with a speed of 0.74c, where c is the speed of light in a vacuum. Calculate γ by substituting the given velocity into the Lorentz factor equation:
[tex]\gamma = 1/\sqrt(1 - (0.74c)^2/c^2)[/tex]
Simplifying this equation,
[tex]\gamma = 1/\sqrt(1 - 0.74^2) = 1/\sqrt(1 - 0.5484) = 1/\sqrt(0.4516) = 1/0.6715 \approx 1.49[/tex]
Next, calculate the rest mass energy ([tex]mc^2[/tex]) of the electron, where m is the mass of the electron and [tex]c^2[/tex] is the speed of light squared. The rest mass energy of an electron is approximately 0.511 MeV (mega-electron volts) or 511 keV.
Finally, calculate the total energy of the electron:
E = (1.49 - 1)(511 keV) = 0.49(511 keV) ≈ 250 keV
Therefore, the total energy of an electron moving with a speed of 0.74c is approximately 250 keV.
Learn more about total energy here:
https://brainly.com/question/14062237
#SPJ11
A generator connected to an RLC circuit has an rms voltage of 150 V and an rms current of 33 mA .A generator connected to an RLC circuit has an rms voltage of 150 V and an rms current of 33 mA .
If the resistance in the circuit is 3.0 kΩ and the capacitive reactance is 6.7 kΩ , what is the inductive reactance of the circuit?
The required solution is:Inductive reactance of the circuit is 1.38 kΩ.
Given information: The rms voltage (Vrms) of the generator = 150 VThe rms current (Irms) in the circuit = 33 mAThe resistance (R) in the circuit = 3.0 kΩThe capacitive reactance (Xc) = 6.7 kΩThe formula to calculate the inductive reactance (XL) of the circuit is given as,XL = √[R² + (Xl - Xc)²]where,XL is the inductive reactanceXc is the capacitive reactance of the circuit. R is the resistance of the circuit.
Substituting the given values in the formula,XL = √[ (3.0 kΩ)² + (Xl - 6.7 kΩ)²]⇒ XL² = (3.0 kΩ)² + (XL - 6.7 kΩ)²⇒ XL² = 9.0 kΩ² + XL² - 2 * 6.7 kΩ * XL + (6.7 kΩ)²⇒ 0 = 9.0 kΩ² - 2 * 6.7 kΩ * XL + (6.7 kΩ)²⇒ 0 = (3.0 kΩ - XL) (3.0 kΩ + XL) - (6.7 kΩ)²XL = (6.7 kΩ)² / (3.0 kΩ + XL)⇒ (3.0 kΩ + XL) XL = (6.7 kΩ)²⇒ XL² + 3.0 kΩ * XL - (6.7 kΩ)² = 0Solving for XL using the quadratic formula, we get,XL = 1.38 kΩ and XL = -4.38 kΩ.
Since inductive reactance can never be negative, we ignore the negative value.So, the inductive reactance of the circuit is 1.38 kΩ (approximately).Hence, the required solution is:Inductive reactance of the circuit is 1.38 kΩ.
Learn more about Inductive reactance here,
https://brainly.com/question/32092284
#SPJ11
A generator supplies 100 V to a transformer's primary coil, which has 60 turns. If the secondary coil has 640 turns, what is the secondary voltage? Number Units
A generator supplies 100 V to a transformer's primary coil, which has 60 turns. If the secondary coil has 640 turns, the secondary voltage is 1067 V.
The voltage ratio in a transformer is equal to the turns ratio. In this case, the turns ratio is given as:
Turns ratio = (Number of turns in secondary coil) / (Number of turns in primary coil)
Given that the number of turns in the primary coil is 60 and the number of turns in the secondary coil is 640, the turns ratio is:
Turns ratio = 640 / 60 = 10.67
The voltage ratio is the same as the turns ratio. Therefore, the secondary voltage can be calculated by multiplying the primary voltage by the turns ratio:
Secondary voltage = (Primary voltage) x (Turns ratio)
Since the primary voltage is given as 100 V, we can calculate the secondary voltage as:
Secondary voltage = 100 V x 10.67 = 1067 V
Therefore, the secondary voltage is 1067 V.
To learn more about transformer visit: https://brainly.com/question/23563049
#SPJ11
Two metal plates with only air between them are separated by 148 cm One of the plates is at a potential of 327 volts and the other plate is at a potential of 341 volts. What is the magnitude of the electric field between the plates in volts/meter? (Enter answer as a positive integer Do not include unit in answer
The magnitude of the electric field between the plates is approximately 9 V/m.
To calculate the magnitude of the electric field between the plates, we can use the formula:
Electric field (E) = Potential difference (V) / Distance (d).
Given that the potential difference between the plates is 341 V - 327 V = 14 V, and the distance between the plates is 148 cm = 1.48 m, we can substitute these values into the formula:
E = 14 V / 1.48 m.
Calculating the value, we find:
E ≈ 9.459 V/m.
Therefore, the magnitude of the electric field between the plates is approximately 9 V/m.
Learn more about magnitude here:
https://brainly.com/question/30033702
#SPJ11
A 3-phase electrical device connected as a Y circuit with each phase having a resistance of 25 ohms. The line voltage is 230 volts.
a. What is the phase current??
In a Y-connected circuit, the line voltage (V_line) is equal to the phase voltage (V_phase). Therefore, the line voltage is 230 volts. The phase current in the Y-connected circuit is 9.2 Amperes.
To calculate the phase current (I_phase), we need to use Ohm's Law. Ohm's Law states that the current (I) flowing through a resistor is equal to the voltage (V) across the resistor divided by the resistance (R).
In this case, the resistance of each phase is given as 25 ohms. Since the line voltage (V_line) is equal to the phase voltage (V_phase), we can use the line voltage in the calculation.
Using Ohm's Law: I_phase = V_phase / R_phase
Since V_line = V_phase, we can substitute the values: I_phase = V_line / R_phase
Substituting V_line = 230 volts and R_phase = 25 ohms, we get:
I_phase = 230 V / 25 Ω = 9.2 Amperes
Therefore, the phase current in the Y-connected circuit is 9.2 Amperes.
To know more about phase current click here:
https://brainly.com/question/19578744
#SPJ11
The sun is 150,000,000 km from earth; its diameter is 1,400,000 km. A student uses a 5.4-cm-diameter lens with f = 10 cm to cast an image of the sun on a piece of paper.
What is the intensity of sunlight in the projected image? Assume that all of the light captured by the lens is focused into the image
The intensity of the incoming sunlight is 1050 W/m²
The intensity of sunlight in the projected image is calculated to bee 7.271x10¹⁹ W/m².
In this scenario, a student utilizes a lens with a diameter of 5.4 cm and a focal length of 10 cm to project an image of the sun onto a piece of paper. The sun, positioned 150,000,000 km away from Earth, has a diameter of 1,400,000 km. The image formed is obtained using the lens formula. It is given by the relation as:
[tex]$$\frac {1}{f}=\frac {1}{u}+\frac {1}{v}$$[/tex]
Using the relation, the image distance (v) can be calculated as;
[tex]$$\frac {1}{10}=\frac {1}{150000000}-\frac {1}{u}$$[/tex]
The value of u comes out to be 1.4999 x 10⁹ m.
Using the formula for magnification, the magnification can be calculated as,
[tex]$$\frac {v}{u}=\frac {h'}{h}$$[/tex]
Where h' is the height of the imageh is the height of the object.
Height of the object, h = 1.4 x 10⁹ mHeight of the image, h' = 0.054 m
Therefore, the magnification is,
[tex]$$M=\frac {0.054}{1.4 x 10^9}=-3.8571x10^{-8}$$[/tex]
The negative sign in the magnification value indicates that the image is formed upside down or inverted. The intensity of sunlight in the projected image is given by the relation;
[tex]$$I'=\frac {I}{M^2}$$[/tex]
Where, I is the intensity of the incoming sunlight
The value of I is given to be 1050 W/m²
Therefore, substituting the given values in the above relation, we get,
[tex]$$I'=\frac {1050}{(-3.8571x10^{-8})^2}$$[/tex]
The value of I' comes out to be 7.271x10¹⁹ W/m².
Learn more about intensity at: https://brainly.com/question/28145811
#SPJ11
f B⇀ represents a magnetic field and A represents the total area of the surface, what does the equation B→·A→=0 describe?
A magnetic field that is everywhere parallel to the surface.
A magnetic field that is uniform in magnitude and everywhere horizontal.
The equation is false because it describes a magnetic monopole, which does not exist.
The equation describes any magnetic field that can exist in nature.
The equation B→·A→=0 accurately describes a magnetic field that is everywhere parallel to the surface, indicating that the magnetic field lines are not intersecting or penetrating the surface but are instead running parallel to it.
The equation B→·A→=0 describes a magnetic field that is everywhere parallel to the surface. Here, B→ represents the magnetic field vector, and A→ represents the vector normal to the surface with a magnitude equal to the total area of the surface A. When the dot product B→·A→ equals zero, it means that the magnetic field vector B→ is perpendicular to the surface vector A→. In other words, the magnetic field lines are parallel to the surface.This scenario suggests that the magnetic field is not penetrating or intersecting the surface, but rather running parallel to it. This can occur, for example, when a magnetic field is generated by a long straight wire placed parallel to a surface. In such a case, the magnetic field lines would be perpendicular to the surface.
Learn more about magnetic field here:
https://brainly.com/question/30331791
#SPJ11
Find the flux of the Earth's magnetic field of magnitude 5.00 ✕ 10-5 T, through a square loop of area 10.0 cm2 for the following.
(a) when the field is perpendicular to the plane of the loop
T·m2
(b) when the field makes a 60.0° angle with the normal to the plane of the loop
T·m2
(c) when the field makes a 90.0° angle with the normal to the plane
T·m2
To find the flux of the Earth's magnetic field through a square loop of area 10.0 cm^2, we need to consider the angle between the magnetic field and the normal plane of the loop.
The flux is given by the product of the magnetic field magnitude and the component of the field perpendicular to the loop, multiplied by the area of the loop.
(a) When the magnetic field is perpendicular to the plane of the loop, the flux is given by the formula Φ = B * A, where B is the magnetic field magnitude and A is the area of the loop. Substituting the given values, we can calculate the flux.
(b) When the magnetic field makes a 60.0° angle with the normal to the plane of the loop, the flux is given by the formula Φ = B * A * cos(θ), where θ is the angle between the magnetic field and the normal to the plane. By substituting the given values, we can calculate the flux.
(c) When the magnetic field makes a 90.0° angle with the normal to the plane, the flux is zero since the magnetic field is parallel to the plane and does not intersect it.
Learn more about magnetic flux here:
https://brainly.com/question/13851713
#SPJ11
Consider an object of mass 100kg. Ignoring the gravitational effects due to any other celestial bodies, work out the following:
(a) What is the work required to move the object from the surface of the earth to a height where it will not feel the effect of the earth’s gravity?
(b) If the object is stationary on the surface of the earth with the full moon directly above it, find the measured weight of the object.
(c) If the object were to float in space between the earth and the moon, find the distance from the earth where the object would experience zero gravitational force on it.
(a) The work required to move the object from the surface of the earth to a height where it will not feel the effect of the earth's gravity can be calculated using the formula for gravitational potential energy.
(b) If the object is stationary on the surface of the earth with the full moon directly above it, the measured weight of the object can be determined by considering the gravitational force between the object and the earth.
(c) To find the distance from the earth where the object would experience zero gravitational force, we can set the gravitational forces due to the earth and the moon equal to each other and solve for the distance.
(a) The work required to move the object from the surface of the earth to a height where it will not feel the effect of the earth's gravity is equal to the change in gravitational potential energy. This can be calculated using the formula W = ΔPE = mgh, where m is the mass of the object, g is the acceleration due to gravity, and h is the height.
(b) The measured weight of the object on the surface of the earth with the full moon directly above it can be found by considering the gravitational force between the object and the earth. The weight of the object is equal to the force of gravity acting on it, which can be calculated using the formula W = mg, where m is the mass of the object and g is the acceleration due to gravity.
(c) To find the distance from the earth where the object would experience zero gravitational force, we can set the gravitational forces due to the earth and the moon equal to each other. By equating the gravitational forces, we can solve for the distance where the gravitational forces cancel out, resulting in zero net force on the object.
Learn more about gravitational potential energy here:
https://brainly.com/question/29766408
#SPJ11
A baseball bat traveling rightward strikes a ball when both are moving at 30.1 m/s (relative to the ground) toward each other. The bat and ball are in contact for 1.10 ms, after which the ball travels rightward at a speed of 42.5 m/s relative to the ground. The mass of the bat and the ball are 850 g and 145 g, respectively. Define rightward as the positive direction.
Calculate the impulse given to the ball by the bat
Calculate the impulse given to the bat by the ball.
What average force ⃗ avg does the bat exert on the ball?
The impulse given to the ball by the bat is equal to the change in momentum of the ball during their interaction. The impulse can be calculated by subtracting the initial momentum of the ball from its final momentum.
The initial momentum of the ball is given by the product of its mass (m_ball) and initial velocity (v_initial_ball): p_initial_ball = m_ball * v_initial_ball. The final momentum of the ball is given by: p_final_ball = m_ball * v_final_ball.
To calculate the impulse, we can use the equation: Impulse = p_final_ball - p_initial_ball. Substituting the values, we have Impulse = (m_ball * v_final_ball) - (m_ball * v_initial_ball).
Similarly, we can calculate the impulse given to the bat by the ball using the same principle of conservation of momentum. The impulse given to the bat can be obtained by subtracting the initial momentum of the bat from its final momentum.
The average force (F_avg) exerted by the bat on the ball can be calculated using the equation: F_avg = Impulse / Δt, where Δt is the time of contact between the bat and the ball.
Learn more about momentum here;
https://brainly.com/question/18798405
#SPJ11
An elevator is hoisted by its cables at constant speed. Is the total work done on the elevator positive, negative, or zero? Explain your reasoning.
The force applied by the cables to lift the elevator is equal to the weight of the elevator, which is mg. Since the elevator is moving at a constant speed, the net force acting on the elevator is zero.
When an elevator is hoisted by its cables at a constant speed, the total work done on the elevator is zero.
The work done on an object is defined as the product of the force applied on it and the displacement caused by that force.
Work done can be positive or negative depending on the direction of the force and the displacement caused by it.
In this case, the elevator is hoisted by its cables at a constant speed. Since the speed is constant, the net force acting on the elevator is zero. This means that no work is being done on the elevator by the cables, and hence the total work done on the elevator is zero.
Let's take an example to understand this better. Suppose an elevator of mass m is being hoisted by its cables with a constant speed v.
The force applied by the cables to lift the elevator is equal to the weight of the elevator, which is mg.
Since the elevator is moving at a constant speed, the net force acting on the elevator is zero.
Therefore, the work done on the elevator by the cables is zero.
In conclusion, when an elevator is hoisted by its cables at a constant speed, the total work done on the elevator is zero.
Learn more about force here:
https://brainly.com/question/30507236
#SPJ11
To push a 28.0 kg crate up a frictionless incline, angled at 25.0° to the horizontal, a worker exerts a force of 219 N parallel to the incline. As the crate slides 1.5 m, how much work is done on the crate by (a) the worker's applied force. (b) the gravitational force or the crate, and (c) the normal force exerted by the incline on the crate? (d) What is the total work done on the crate? (a) Number ______________ Units ________________
(b) Number ______________ Units ________________
(c) Number ______________ Units ________________
(d) Number ______________ Units ________________
To push a 28.0 kg crate up a frictionless incline, angled at 25.0° to the horizontal, a worker exerts a force of 219 N parallel to the incline.
Mass, m = 28.0 kg, angle of inclination, θ = 25.0°, distance travelled, d = 1.5 m, applied force, F = 219 N.
Work is defined as the product of the applied force and the displacement of the object. It is represented by W.
So, the work done by the worker is calculated as follows
:W = Fdcos∅
W = 219*1.5cos 25.0°
W = 454.8J
So, the work done by the worker is 454.8 J.
The gravitational force acting on the crate can be calculated as follows:
mg = 28.0*9.8 = 274.4N
Now, the work done by the gravitational force can be calculated as follows:
W = mgh
W = 28.0*9.8*1.5sin 25.0°
W = 362.3J
So, the work done by the gravitational force is 362.3 J.
The normal force is equal and opposite to the component of the gravitational force acting perpendicular to the incline, that is,
N = mgcos∅
Now, the work done by the normal force can be calculated as follows:
W = Ndcos (90.0° - ∅ )
W = mgcos∅*dsin∅
W = 28.0*9.8*1.5*sin 25.0°*cos 65.0°
W = 98.1J
So, the work done by the normal force is 98.1 J.
The total work done on the crate is the sum of the work done by the worker, gravitational force and normal force.
W_total = W_worker + W_gravity + W_normaW_total = 454.8+ 362.3+ 98.1
W_total= 915.2
Hence, the total work done on the crate is 915.2 J.
a) The work done by the worker is 454.8 J.
(b) The work done by the gravitational force is 362.3 J.
(c) The work done by the normal force is 98.1 J.
(d) The total work done on the crate is 915.2 J.
Learn more on how incline affects force applied: https://brainly.com/question/11544063
#SPJ11