The mode of operation refers to the operation of MOSFET transistors that changes as the gate-to-source voltage (Vgs) is varied.
They operate in one of three modes: cutoff, triode, and saturation modes. A particular n-channel MOSFET has the following specifications: kn' = 5x10^-³ A/V² and V₁=1V. The width, W, is 12 um and the length, L, is 2.5 μm.a) If VGs = 0.1V and VDs = 0.1V, what is the mode of operation? Find Ip.
Calculate Ròs.The transistor is in the cut-off mode of operation if the gate voltage is less than the threshold voltage. In this instance, Vgs < Vth, the MOSFET is in the cut-off mode.
Vgs = 0.1V < Vth, and VDs = 0.1V is less than Vgs - Vth, making the transistor in the triode region.Id = (5 x 10^-3 A/V^2) /2 (0.012) (0.1 - 0) ^2 = 2.25 x 10^-6 A.Ros = ΔVds/ ΔId= 0.1V / 2.25x10^-6A = 4.4x10^4 Ωb) If VGS = 3.3V and VDs = 0.1V, what is the mode of operation? Find Ip. Calculate RDs.
In the saturation mode, if Vgs is sufficiently high, the MOSFET is in the saturation region. In this instance, Vgs > Vth, and Vds < Vgs - Vth, and the MOSFET is in saturation mode.Id = (5 x 10^-3 A/V^2)/2(0.012) (3.3 - 1)^2= 5.76 x 10^-4A.RDs = ΔVds / ΔId= 0.1V / 5.76x10^-4A = 173.6 Ωc) If VGS = 3.3V and VDs = 3.0V, what is the mode of operation? Find Ip. Calculate Rps.
In this instance, the MOSFET is in the saturation region because Vgs > Vth, and Vds > Vgs - Vth.Id = 0.5(5 x 10^-3 A/V^2) (12/2.5)^2 (3.3 - 1)^2= 3.856 mA.Rps = ΔVds / ΔId= 3.0V / 3.856mA = 778.14 Ω.
To learn more about mode :
https://brainly.com/question/28566521
#SPJ11
Determine the dryness fraction of a steam in an enclosed cylinder if the mass of dry steam is 10kg and the mass of liquid in suspension is 2kg? a 0.85 b. 0.83 C. 0.81 d. 0.79 27.
To determine the dryness fraction of the steam, we need to calculate the ratio of the mass of dry steam to the total mass of the mixture, which includes both the dry steam and the liquid in suspension.
Given:
Mass of dry steam = 10 kg
Mass of liquid in suspension = 2 kg
Total mass of the mixture = Mass of dry steam + Mass of liquid in suspension
Total mass of the mixture = 10 kg + 2 kg
Total mass of the mixture = 12 kg
Dryness fraction = Mass of dry steam / Total mass of the mixture
Dryness fraction = 10 kg / 12 kg
Dryness fraction ≈ 0.8333
Rounded to two decimal places, the dryness fraction is approximately 0.83.
Therefore, the answer is option b) 0.83.
To know more about dryness fraction, visit;
https://brainly.com/question/30457474
#SPJ11
a) Denise Output Reostance Date: D) Denve Gain
The development of remote work has been a significant change in the workforce over the past few years, with the Covid-19 pandemic accelerating this trend.
Before the Covid-19 pandemic, remote work was already becoming more popular, especially among tech companies and startups. Many companies allowed employees to work from home a few days a week, and some even had fully remote teams.
This was made possible by the development of technology such as video conferencing, online collaboration tools, and cloud-based software. However, remote work was still not the norm, and many companies and industries were hesitant to adopt it.
During the Covid-19 pandemic, remote work became a necessity for many companies as offices were closed and social distancing measures were put in place. This forced companies to quickly adapt to remote work and find ways to make it work for their employees.
To know more about significant visit:
https://brainly.com/question/31037173
#SPJ11
1) Besides WireShark, what other tools are available to enable packet sniffing?
a. Describe at least two that are freely available on your favorite OS. (include URL)
b. What features do they offer over WireShark and vice versa?
The other tools available for packet sniffing,
a. Freely available packet sniffing tools are tcpdump & TShark
b. Wireshark provides a comprehensive GUI-based packet analysis experience, tcpdump and TShark offer command-line alternatives with lightweight and scriptable capabilities.
Besides Wireshark, there are several other tools available for packet sniffing.
a. Here are two freely available tools on popular operating systems:
tcpdump:
URL: https://www.tcpdump.org/
Operating System: Linux, macOS, Windows (through WinDump)
Features:
Tcpdump is a command-line packet analyzer that captures network packets and displays detailed packet information.
It provides a wide range of filtering options to capture specific packets based on protocols, source/destination IP addresses, port numbers, etc.
Tcpdump offers advanced capabilities for packet analysis, including the ability to decode and display packet contents in various formats.
It is highly customizable and can be integrated with other tools for further analysis or automation.
TShark (part of Wireshark):
URL: https://www.wireshark.org/docs/man-pages/tshark.html
Operating System: Linux, macOS, Windows
Features:
TShark is a command-line tool that is part of the Wireshark suite. It offers similar functionality to Wireshark but without the GUI.
It can capture, analyze, and display network packets in real-time or from saved capture files.
TShark supports various display and filter options to extract specific information from packet captures.
It is scriptable and can be used for automated packet analysis and processing.
b. Comparing these tools with Wireshark:
Wireshark: Wireshark provides a comprehensive and user-friendly graphical interface for packet analysis. It offers advanced features like real-time traffic monitoring, in-depth packet inspection, protocol decodes, and powerful filtering capabilities. Wireshark is widely used by network professionals for in-depth analysis and troubleshooting.
tcpdump: Tcpdump is a command-line tool that offers similar functionality to Wireshark but without the GUI. It is lightweight and efficient, making it suitable for capturing packets on servers or systems with limited resources. Tcpdump is commonly used in combination with other command-line tools for scripting or automation purposes.
TShark: TShark is a command-line tool from the Wireshark suite that provides similar functionality to Wireshark but without the GUI. It is useful for scenarios where a graphical interface is not available or necessary. TShark offers scriptability and can be integrated into automated workflows or used in remote environments.
In summary, while Wireshark provides a comprehensive GUI-based packet analysis experience, tcpdump and TShark offer command-line alternatives with lightweight and scriptable capabilities. The choice between these tools depends on the specific requirements, resources, and preferences of the user.
To learn more about packet sniffing visit:
https://brainly.com/question/29872178
#SPJ11
You have a very large file named music_types and the first five lines on this file are: country rock music:4000210 light rock music:1001380 classic rock music:1002252 alternative rock music:2303122 fusion rock music:10074432 Write a sequence of UNIX/Linux commands (joined by pipes) that will: (a) replace the word "music" with the word "song"; (b) make all letters uppercase and (c) store the results in a new file called modified_music_types
To accomplish the task, you can use the following sequence of UNIX/Linux commands joined by pipes:
(a) sed 's/music/song/g' music_types |
(b) tr '[:lower:]' '[:upper:]' |
(c) tee modified_music_types
In summary, the commands use "sed" to replace the word "music" with "song" in the file "music_types". Then, "tr" is used to convert all letters to uppercase. Finally, "tee" is used to store the modified content in a new file called "modified_music_types".
(a) The command "sed 's/music/song/g' music_types" uses sed (stream editor) to substitute all occurrences of "music" with "song" in the file "music_types".
(b) The command "tr '[:lower:]' '[:upper:]'" utilizes the "tr" command to translate all lowercase letters to uppercase.
(c) The command "tee modified_music_types" redirects the output to both the terminal and the file "modified_music_types" using the "tee" command. This creates a new file with the modified content.
Learn more about Linux commands here
https://brainly.com/question/30389482
#SPJ11
Suppose we are given the following information about a signal x[n]: 1. x[n] is real and even. 2. x[n] has period N= 15 and has Fourier coefficients ak 3. a16 = 2. 4. 1o|x[n]|² = 8. 15 Identify the signal x[n]. (10 marks) [CLO 3]
The signal x[n] is a real and even periodic signal with a period of 15, but its specific form or shape cannot be determined.
To identify the signal x[n], we can use the given information and properties of the signal.
1. The signal x[n] is real and even. This means that x[n] is symmetric around the y-axis, and its Fourier coefficients will have conjugate symmetry.
2. x[n] has a period N = 15. This implies that x[n] repeats itself every 15 samples.
3. We are given a specific Fourier coefficient: a16 = 2. Since x[n] is even, we know that a[n] = a[-n]. Therefore, a[-16] = a16 = 2.
4. We are also given that the average power of the signal, 1/N * |x[n]|², is equal to 8. Since x[n] is even, the power is the same for positive and negative values. So, the sum of the squared magnitudes of the Fourier coefficients should be 8 * N.
Based on the given information, we can conclude that the signal x[n] is a periodic real and even signal with a period of 15. The specific Fourier coefficient a16 = 2 confirms the conjugate symmetry of the coefficients. However, without additional information or the actual Fourier coefficients, we cannot determine the exact form or shape of the signal x[n].
Learn more about signal:
https://brainly.com/question/30130156
#SPJ11
12.23 In a certain medium, the phase velocity is 2 λ, ир = с -- λ where c = 3 X 108 m/s. Obtain the expression for the group velocity.
The expression for the group velocity can be obtained by differentiating the dispersion relation with respect to the wave number k.
The given dispersion relation is:
v_phase = 2λ/τ - λ (where c = 3 × 10^8 m/s)
Let's rewrite the dispersion relation as:
τ = λ(2/τ - 1)
Now, we differentiate both sides of the equation with respect to the wave number k:
dτ/dk = d(λ(2/τ - 1))/dk
Using the chain rule, we can expand the derivative as:
dτ/dk = λ(d(2/τ - 1)/dτ) * (dτ/dk)
Simplifying, we get:
dτ/dk = λ(-2/τ^2) * (dτ/dk)
Since dτ/dk is the group velocity v_group, we can rewrite the equation as:
v_group = -2λ/τ^2
Substituting the expression for τ from the dispersion relation, we have:
v_group = -2λ/(λ(2/τ - 1))^2
Simplifying further, we get:
v_group = -2c^2/((2/τ - 1)^2)
Conclusion:
The expression for the group velocity in the given medium is -2c^2/((2/τ - 1)^2), where c = 3 × 10^8 m/s and τ represents the wavelength λ.
To know more about velocity, visit
https://brainly.com/question/80295
#SPJ11
Consider the following text: retrieve remove data retrieved reduce povemove o a. How many character trigram dictionary entries are generated by indexing the trigrams in the terms in the text above? Use the special character $ to denote the beginning and end of terms. b. How would the wild-card query re*ve be most efficiently expressed as an AND query using the trigram index over the text above? c. Explain the necessary steps involved in processing the wild-card query red using the trigram index over the text above? [3+2+3=8M]
a. The text generates 37 character trigram dictionary entries by indexing the trigrams in the terms.
b. The wild-card query "re*ve" can be efficiently expressed as an AND query using the trigram index by searching for terms that match the trigrams "re$" and "$ve".
c. Processing the wild-card query "red" using the trigram index involves searching for terms that match the trigrams "re$" and "$ed", followed by post-processing to filter out terms that do not match the desired pattern.
a. To generate character trigram dictionary entries, we index the trigrams in the terms of the text. Considering the text "retrieve remove data retrieved reduce povemove o", the trigrams would be: "$re", "ret", "etr", "tri", "rie", "iev", "eve", "ver", "rem", "emo", "mov", "ove", "rem", "emo", "mov", "ove", "dat", "ata", "ret", "etr", "tri", "rie", "iev", "eve", "ver", "edu", "duc", "uce", "ced", "edu", "duc", "uce", "pov", "ove", "vem", "emo", "mov", "ove", "o$". So, there are 37 character trigram dictionary entries.
b. To express the wild-card query "re*ve" efficiently as an AND query using the trigram index, we can search for terms that match the trigrams "re$" and "$ve". By performing an AND operation between the matching terms, we can retrieve the terms that have both trigrams in their character trigram representation, effectively matching the wild-card query.
c. Processing the wild-card query "red" using the trigram index involves searching for terms that match the trigrams "re$" and "$ed". After retrieving the matching terms, a post-processing step is required to filter out terms that do not match the desired pattern. In this case, we would need to check if the retrieved terms have the desired pattern of "red" by examining the actual character sequence. This step ensures that only terms containing "red" in the desired position are returned as query results, while excluding any false positives that may match the trigrams but not the desired pattern.
Learn more about query here
https://brainly.com/question/31946510
#SPJ11
The weak acid HX has a pka - 5.74. If 20.00 mL of 0.100 MHX are titrated with 0.100 M sodium hydroxide solution, what is the pH at the equivalence point?
Acid-base titration is a laboratory procedure for determining the quantity or concentration of an acid or base in a given solution. The equivalence point in an acid-base titration is the point at which the number of moles of acid is equal to the number of moles of base used in the titration.
The pH of a weak acid solution changes as more base is added during the titration, but the change is not as rapid as in the case of strong acid titrations. Before the equivalence point, the pH of the solution is determined by the concentration of the weak acid. After the equivalence point, the pH is determined by the excess sodium hydroxide solution present in the solution. At the equivalence point, the amount of base added is equal to the amount of acid present, and the pH of the solution is that of the salt formed. The pH of the salt formed depends on the cation and anion present in the solution.The volume of HX used in the experiment can be calculated as follows:20.00 mL of 0.100 MHX = (20.00/1000) x 0.100 mol/L = 0.002 molNaOH is a strong base, thus its concentration can be used to calculate the number of moles present in the solution as follows:0.002 mol HX = 0.002 mol .NaOHThe volume of NaOH used to reach the equivalence point can be determined as follows:0.100 M NaOH x VNaOH = 0.002 mol NaOHVNaOH = 0.002 mol/0.100 mol/L = 0.02 L = 20 mLThe pH of the weak acid solution at the equivalence point can be calculated by taking into account the salt formed.To know more about titration click the link below:
brainly.com/question/22264846
#SPJ11
Identify the expression from the list below that can be used to derive the integral control signal u □ a. u = kjè b. None of the answers given O c.uk, e dt O d.ů = k₁e
The expression from the given list that can be used to derive the integral control signal u is option c: u = k∫e dt.
In a control system, the integral control component is responsible for reducing steady-state errors by integrating the error signal over time. The integral control signal u is proportional to the integral of the error signal e with respect to time.
The integral control signal can be mathematically represented as:
u = k∫e dt
Here, k is the gain of the integral controller, and the integral of the error signal e with respect to time is denoted by ∫e dt. The integration represents the accumulation of the error over time, which allows the integral control to take corrective actions and eliminate steady-state errors.
Therefore, the expression u = k∫e dt is the correct b for deriving the integral control signal u in a control system.
The integral control signal u in a control system can be derived using the expression u = k∫e dt, where k is the gain of the integral controller and ∫e dt represents the integral of the error signal e with respect to time. This expression captures the accumulation of error over time and enables the integral control component to eliminate steady-state errors.
To know more about the integral, visit;
https://brainly.com/question/30094386
#SPJ11
a) Explain three ways you can save energy by reducing the power consumption of your computer? b) How do you know when a cell is selected?
a) There are three ways to save energy by reducing the power consumption of a computer:
i) Adjusting power settings and optimizing energy-saving features, ii) Properly managing computer peripherals.
iii) Adopting efficient hardware and software practices.
b) The selection of a cell is typically indicated by visual cues such as highlighting or a change in appearance, allowing users to identify which cell is currently selected.
a) To save energy and reduce power consumption, one can adjust power settings and optimize energy-saving features on the computer. This includes enabling power-saving modes such as sleep or hibernate when the computer is idle for a specified period. Additionally, reducing screen brightness, setting shorter sleep and screen timeout periods, and managing power-hungry applications can also contribute to energy efficiency.
Properly managing computer peripherals such as printers, scanners, and external storage devices by turning them off when not in use further reduces power consumption. Lastly, adopting efficient hardware and software practices such as using energy-efficient components, updating software and drivers, and minimizing background processes can optimize power usage.
b) The indication of a selected cell in a computer application or software, such as a spreadsheet or table, varies depending on the user interface design. Typically, when a cell is selected, it is visually highlighted or surrounded by a border. This visual cue helps users identify the active or focused cell.
The highlight may be in the form of a different background color, a bold border, or any other visual representation that distinguishes the selected cell from others. Additionally, when a cell is selected, the software may provide other feedback, such as displaying the cell's coordinates or activating specific functions or tools associated with cell manipulation. The selection indication serves as a visual aid, enabling users to perform actions on the desired cell and navigate within the application effectively.
Learn more about power consumption here:
https://brainly.com/question/32435602
#SPJ11
Design an operational amplifier circuit satisfying out = 1.5v.
To design an operational amplifier circuit satisfying out = 1.5V, Choose an operational amplifier with appropriate specifications and gain configuration. Determine the required gain of the circuit based on the input and desired output voltage. Select appropriate resistors and feedback configuration to achieve the desired gain.
To design an operational amplifier (op-amp) circuit that produces an output voltage of 1.5V, we need to carefully choose the op-amp and configure its gain.
In step 1, selecting the right op-amp involves considering factors such as input and output voltage range, bandwidth, slew rate, and noise characteristics. Based on the specific requirements of the application, an op-amp with suitable specifications can be chosen.
In step 2, we determine the required gain of the circuit. If we assume an ideal op-amp with infinite gain, we can use a non-inverting amplifier configuration. The gain (A) of a non-inverting amplifier is given by the formula: A = 1 + (Rf/Rin), where Rf is the feedback resistor and Rin is the input resistor. By rearranging this formula, we can calculate the necessary values for Rf and Rin to achieve the desired gain.
In step 3, we select appropriate resistor values based on the calculated gain. The feedback resistor (Rf) and input resistor (Rin) can be chosen from standard resistor values available in the market. By carefully selecting these resistors and connecting them in the non-inverting amplifier configuration, we can achieve the desired output voltage of 1.5V.
Learn more about operational amplifier
brainly.com/question/31043235
#SPJ11
Complete the following program to make it output a list of student IDs with each student's last grade as shown in the expected output.
students = {
'6422771001': ['A', 'B', 'B', 'C', 'A'],
6422771002: ['B', 'B+', 'B', 'C'],
'6422771003': ['C', 'C', 'D', 'A', 'D'],
'6422771004': ['D', 'A', 'B', 'C']
2
#Expected output
#6422771001 A
10 # 6422771002 C
# 6422771003 D
12#6422771004 C
To output a list of student IDs with each student's last grade, we can iterate through the dictionary 'students' and print the student ID along with the last grade from their respective value lists. Below is the completed program:
students = {
'6422771001': ['A', 'B', 'B', 'C', 'A'],
6422771002: ['B', 'B+', 'B', 'C'],
'6422771003': ['C', 'C', 'D', 'A', 'D'],
'6422771004': ['D', 'A', 'B', 'C']
}
for student_id, grades in students.items():
last_grade = grades[-1] # Get the last grade from the list of grades
print(student_id, last_grade)
# Expected output:
# 6422771001 A
# 6422771002 C
# 6422771003 D
# 6422771004 C
In this program, we iterate through the 'students' dictionary using the `.items()` method, which returns each key-value pair. For each student, we access their list of grades using the 'grades' variable. By using the index `-1`, we retrieve the last grade from the list. Finally, we print the student ID along with their last grade.
Learn more about list indexing in Python here:
https://brainly.com/question/30396386
#SPJ11
One kg-moles of an equimolar ideal gas mixture contains H2 and Ny at 300°C is contained in a 5 mºtank. The partial pressure of H2 in bar is O 2 175 O 1.967 O 1.191 0 2383
The partial pressure of H2 in the equimolar ideal gas mixture containing H2 and Ny at 300°C, contained in a 5 mº tank, is 1.967 bar.
To find the partial pressure of H2 in the gas mixture, we need to consider Dalton's law of partial pressures. According to Dalton's law, the total pressure exerted by a mixture of ideal gases is equal to the sum of the partial pressures of each gas component.
Given that the equimolar ideal gas mixture contains H2 and Ny (which is presumably nitrogen, but the symbol provided is unclear) and the total pressure is not provided, we'll assume the total pressure is unknown and denote it as P_total.
Since the mixture is equimolar, we can assume that the mole fraction of H2 and Ny is equal. Let's denote this mole fraction as x. Therefore, the mole fraction of H2 (denoted as X_H2) and Ny (denoted as X_Ny) will both be x.
Using the ideal gas equation, we can relate the partial pressure, mole fraction, and total pressure as follows:
P_H2 = X_H2 * P_total
P_Ny = X_Ny * P_total
Since X_H2 = X_Ny = x, we can rewrite the equations as:
P_H2 = x * P_total
P_Ny = x * P_total
Given that the partial pressure of H2 (P_H2) is 1.967 bar, we can substitute the values:
1.967 bar = x * P_total
However, we do not have enough information to determine the value of x or P_total. Therefore, without additional data, we cannot calculate the partial pressure of H2 accurately.
learn more about ideal gas mixture here:
https://brainly.com/question/13039929
#SPJ11
Question 4
An art professor takes slide photographs of a number of paintings reproduced in a book and used them in her class lectures. Is this considered as copyright law violation? Explain.
Question 9
In your opinion, why plagiarism is considered as unethical action? Give convincing answer and justify it using one of the ethical theories
Question 11
You are managing a department and one of the employees Ahmed, for some emergency reasons, will be away for some days. One employee Faisal has been assigned a task to finish Ahmed work. Faisal requested from you to have all Ahmed files to be copied to his computer. What will be your decision? Justify your answer,
Question 12
How do we differentiate between hacktivists and cyberterrorists?
Using slide photographs of paintings in lectures may be a copyright violation, and plagiarism is unethical while differentiating hacktivists and cyber terrorists depends on motives and consequences.
1. Use of Slide Photographs: Using slide photographs of paintings reproduced in a book in a classroom lecture may potentially be considered a copyright law violation. However, it depends on factors such as the purpose of use, whether it qualifies as fair use, and if appropriate permissions or licenses have been obtained.
2. Plagiarism as Unethical: Plagiarism is considered unethical because it involves presenting someone else's work or ideas as one's own, which undermines the principles of honesty, integrity, and intellectual property rights. From the perspective of ethical theories, plagiarism can be seen as a violation of Kantian ethics, which emphasizes the importance of treating others with respect and not using them solely as a means to an end.
3. Decision on File Copying: The decision to copy Ahmed's files to Faisal's computer would depend on several factors. It is essential to consider the nature of the files, the sensitivity of the information they contain, and the organizational policies regarding data access and security. Justification for the decision should be based on principles such as privacy, data protection, and ensuring that Faisal has the necessary resources and support to complete Ahmed's work effectively.
4. Differentiating Hacktivists and Cyberterrorists: Hacktivists and cyberterrorists can be differentiated based on their motives and objectives. Hacktivists are individuals or groups who engage in hacking activities to promote a social or political cause, often aiming to expose wrongdoing or advocate for change. Cyberterrorists, on the other hand, use hacking and cyber-attacks to create fear, disrupt critical infrastructure, or advance ideological or political agendas. The distinction lies in the intent and the consequences of their actions, with cyberterrorists seeking to cause harm and instill fear, while hacktivists focus on activism and raising awareness through technology.
Learn more about violations here
https://brainly.com/question/31558707
#SPJ11
9. What is the time complexity of the rotations used with red-black trees? What is the reason for this complexity? (10 pts)
The time complexity of the rotations used with red-black trees is O(1), which means they have a constant time complexity. The reason for this constant time complexity is that rotations in red-black trees involve a fixed number of pointer updates and do not depend on the size or height of the tree.
Red-black trees maintain balance by performing left and right rotations to preserve the red-black properties. These rotations rearrange the tree's structure while maintaining the relative ordering of the elements.
Both left and right rotations involve adjusting a constant number of pointers without traversing the entire tree. In a left rotation, a constant number of pointers are updated to rotate the tree to the left, and in a right rotation, a constant number of pointers are updated to rotate the tree to the right. These pointer updates can be performed in a constant amount of time, regardless of the size or height of the tree.
As a result, the time complexity of rotations in red-black trees is considered O(1), providing efficient balancing operations for maintaining the tree's properties.
Learn more about time complexity here:
https://brainly.com/question/31359012
#SPJ11
Given the fractional composition of our atmosphere (20.95% Oxygen, 78.1% Nitrogen, and 0.03% Carbon Dioxide), create a table that provides the partial pressure and fractional composition of each one of these gases at the following atmospheric pressures. 101 kPa, 95 kPa, 85 kPa, 76 kPa, 61 kPa, 50 kPa, 35 kPa b. 760 mm Hg, 850 mm Hg, 970 mm Hg, 1050 mm Hg
The table below provides the partial pressure and fractional composition of Oxygen, Nitrogen, and Carbon Dioxide at various atmospheric pressures, including 101 kPa, 95 kPa, 85 kPa, 76 kPa, 61 kPa, 50 kPa, 35 kPa, 760 mm Hg, 850 mm Hg, 970 mm Hg, and 1050 mm Hg.
To calculate the partial pressure of a gas, we multiply the atmospheric pressure by the fractional composition of the gas. The fractional composition is given as a percentage, so we convert it to a decimal by dividing by 100. Here's the table:
As the atmospheric pressure decreases, the partial pressure of each gas also decreases proportionally. However, the fractional composition remains constant regardless of the atmospheric pressure. The partial pressure and fractional composition of carbon dioxide remain constant at 0.03 kPa and 0.0003, respectively, as its concentration is relatively stable in the atmosphere.
Learn more about partial pressure here:
https://brainly.com/question/30114830
#SPJ11
The following test harness has been developed for the LazyArray class from the lectures.
method LazyArray TestHarness() {
var arr := new LazyArray(3, 4); assert arr.Get(0) == arr.Get(1) == 4; }
arr.Update(0, 9);
arr.Update(2, 1);
assert arr.Get(0) == 9 && arr.Get(1) == 4 && arr.Get(2) == 1;
The first assertion is true.
a. True
b. False
The first assertion in the given test harness is false.
The first assertion in the test harness states that arr.Get(0) == arr.Get(1) == 4. This means that the values returned by arr.Get(0) and arr.Get(1) should both be equal to 4. However, according to the code snippet provided, the LazyArray object arr is initialized with dimensions 3x4. Therefore, arr.Get(0) and arr.Get(1) would actually return the values at different positions in the array.
Since the LazyArray object is initialized with dimensions 3x4, the positions in the array would be as follows:
arr.Get(0) would correspond to the value at position (0, 0) in the array.
arr.Get(1) would correspond to the value at position (0, 1) in the array.
Since the values at these positions are not set explicitly in the given code snippet, their default value would be 0. Therefore, the first assertion arr.Get(0) == arr.Get(1) == 4 would evaluate to 0 == 0 == 4, which is false. Thus, the correct answer is b. False.
Learn more about array here:
https://brainly.com/question/13261246
#SPJ11
The parts of this problem are based on Chapter 5. (a) (10 pts.) Consider a linear time-invariant system whose input has Fourier transform X(jw) and whose output is y(t) = e−(a+2)tu(t). Use Fourier techniques to determine the impulse response h(t). Express answer in the form A8(t) + Be¬Ctu(t). a+5+jw (a+2+jw)² (b) (10 pts.) Consider a linear time-invariant system with H(ejw) = tude response |H(ejw)|. = = 1+e-jw (1—ª‡½e-jw)2· Determine the magni- 1000(10+jw) (100+jw)² (jw)² (400+jw) (800+jw)* Determine the (c) (10 pts.) Consider a linear time-invariant system with H(jw) VALUE of the Bode magnitude approximation in dB at w = 100(2) and the SLOPE of the Bode magnitude approximation in dB/decade at w = = 100(a + 1) - 50.
The value of Bode magnitude approximation at ω = 200 is -67.4 dB and the slope of the Bode magnitude approximation in dB/decade at ω = 150 is -60 dB/decade.
Given linear time-invariant system:
[tex]y(t) = e^(-(a+2)t)u(t)[/tex]and
Fourier transform:
X(jω)The impulse response h(t) can be calculated using the Fourier techniques as follows:
[tex]y(t) = h(t) * u(t) -->[/tex]
Taking Fourier Transform on both sides
[tex]Y(jω) = H(jω) X(jω)H(jω) = Y(jω) / X(jω)Here, Y(jω) = L{y(t)} = ∫ y(t) e^(-jωt) dt = ∫ e^(-(a+2)t) e^(-jωt) dt = 1/(a+2+jω)Similarly, X(jω) = L{x(t)}H(jω) = Y(jω) / X(jω) = (1/(a+2+jω)) / ((a+5+jω) * (a+2+jω)^2) = A/(a+2+jω) + B/(a+5+jω) + C/(a+2+jω)^2[/tex]
Hence, the magnitude of the system is [tex]|H(e^jω)| = |[1+e^(-jω)] / [1-e^(-jω)]^2[/tex]|Using the formula of magnitude of a complex number[tex]z = |z| = √(real(z)^2 + imag(z)^2)Now, let H(e^jω) = |H(e^jω)| * e^(jθ)[/tex]where, [tex]|H(e^jω)| = √(real(H(e^jω))^2 + imag(H(e^jω))^2)θ = tan^-1(imag(H(e^jω))/real(H(e^jω)))[/tex]
To know more about magnitude visit:
https://brainly.com/question/31022175
#SPJ11
: At room temperature the static relative permittivity of water is 80. A plot of tan(8) against frequency shows a maximum of 3.3 at a frequency of 30 GHz. Deduce the refractive index of water and the relaxation time for water dipoles in the visible spectral region. What is the frequency difference in the photons emitted in a normal Zeeman effect corresponding to transitions from adjacent magnetic sub-levels to the same final state in a magnetic field, B, of 1.2 Tesla?
1. The refractive index of water can be deduced as the square root of the static relative permittivity, which gives a value of approximately 8.94.
The relaxation time for water dipoles in the visible spectral region can be determined using the maximum value of the tangent function, which occurs at a frequency of 30 GHz. However, the given information does not provide a direct relation between the tangent function and the relaxation time, so it is not possible to calculate the relaxation time based on the given data.
2. To calculate the refractive index of water, we use the formula n = √(ε_r), where ε_r is the static relative permittivity of water. Substituting the given value, we find n = √80 ≈ 8.94. However, the given information about the tangent function and frequency does not directly provide the relaxation time for water dipoles in the visible spectral region. Therefore, we cannot calculate the relaxation time based on the given data.
3. In conclusion, the refractive index of water is approximately 8.94 based on the given static relative permittivity. However, we cannot determine the relaxation time for water dipoles in the visible spectral region from the information provided about the tangent function and frequency.
To know more about Refractive index , visit:- brainly.com/question/30761100
#SPJ11
Let the alphabet be A = {a, 1)
1. {ε} U {b} = 2) {a, b} U {ab} 3) {a, b, ab}{b} 4) {a, b, ab}{ & } 5) L= {b, ab}, L²= 6) {a}* = 7) {a, ab}* = 8) {a}* U {b} = 9) {a}* {b} = 10) {b}{a}* = 11) Ø* = 12) {ε}* =
Answer:
Based on the given alphabet A = {a, 1), the possible solutions are:
{ε, b} Explanation: The given set {ε} U {b} contains an empty string and the symbol 'b' only.
{a, b, ab} Explanation: The given set {a, b} U {ab} contains all possible combinations of the symbols 'a' and 'b', including 'ab'.
{a, b, ab, bb} Explanation: The given set {a, b, ab} contains all possible combinations of the symbols 'a' and 'b', including 'ab'. Adding the symbol 'b' separately results in {a, b, ab, bb}.
{ } Explanation: The given set {a, b, ab} does not contain the empty string, so { } is the only possibility for a set containing no strings.
L² = {bb, babb} Explanation: The given language L = {b, ab} contains the strings 'b' and 'ab'. The language L² is formed by concatenating two strings from L, giving {bb, babb}.
{aⁿ: n ≥ 0} Explanation: The given set {a}* represents all possible combinations of the symbol 'a', including the empty string.
{w: w contains at least one 'a' or 'ab'} Explanation: The given set {a, ab}* represents all possible combinations of the symbols 'a' and 'ab'. Therefore, {w: w contains at least one 'a' or 'ab'} is also a valid solution.
{aⁿ: n ≥ 0} U {b} Explanation: The given set {a}* represents all possible combinations of the symbol 'a', including the empty string. Adding the symbol 'b' separately results in {aⁿ: n ≥ 0} U {b}.
{aⁿbⁿ: n ≥ 0} Explanation: The given set {a}* {b} represents all possible combinations of the symbol 'a', followed by a single 'b'. Therefore, {aⁿbⁿ: n ≥ 0} is a valid solution.
{b, baⁿ: n ≥ 0} Explanation: The given set {b} {a}* represents all possible combinations of the symbol 'a' preceded by a single 'b'. Adding the symbol
Explanation:
Transform the following grammar into an equivalent grammar that has no A-productions. S→ SaB Cb B → Bb | A C → cSd | A. Transform the following grammar into an equivalent grammar in Chomsky normal form. S →gAbs | Ab A → gaba | b.
To transform the given grammar into an equivalent grammar without A-productions and Chomsky normal form, we need to eliminate the A-productions and convert the remaining productions into the desired form.
Removing A-productions:
To eliminate the A-productions (productions of the form A → α), we can substitute each A-production with the corresponding production rules that involve A on the right-hand side. In the given grammar, we have two A-productions:
S → SaB
C → A
By substituting the first A-production, we get:
S → SaB → (SaB)b → SabBb
Substituting the second A-production, we get:
C → A → gaba
Now, the grammar has no A-productions.
Conversion to Chomsky Normal Form (CNF):
In Chomsky normal form, all productions must be of the form:
A → BC
A → a
To convert the grammar into CNF, we need to modify the existing productions. In the given grammar, we have the following productions:
S → SabBb
B → Bb
C → gaba
To convert these productions into CNF, we can introduce new non-terminal symbols and rewrite the productions as follows:
S → X1Y1
X1 → Sa
Y1 → Z1b
Z1 → aB
B → X2b
X2 → b
C → gaba
Now, the grammar is in Chomsky normal form.
In summary, we have transformed the given grammar into an equivalent grammar without A-productions and in Chomsky normal form. The resulting grammar has the following productions:
S → X1Y1
X1 → Sa
Y1 → Z1b
Z1 → aB
B → X2b
X2 → b
C → gaba
Learn more about Chomsky normal form here
https://brainly.com/question/31771673
#SPJ11
Java Homework
(a)Use random numbers to simulate rolling 4 dice 1000 times. Please attach the code.
(b) How to control the random numbers to appear in the same order every time?
How to ensure that the random numbers appear in a different order every time?
Please attach the code.
(Controlling the random numbers to appear in the same order every time means that each
time the program is executed, the generated random number sequence is the same. On the
contrary, each time the program is executed, the generated random number sequence is
different.)
(c) For the 1000 controlled results, please use Array to count the number of occurrences of
each point (4~24), and attach the code and statistical results.
(d) For the 1000 controlled results, please use the Map Interface of Collection API to count
the number of occurrences of each point (4~24), and attach the code and statistical results.
The code that simulates rolling 4 dice 1000 times and counts the number of occurrences of each point using both an array and the Map interface of the Collection API:
import java.util.*;
public class DiceRollSimulation {
public static void main(String[] args) {
// Simulate rolling 4 dice 1000 times
int rolls = 1000;
int[] results = new int[rolls];
// Generate random numbers to simulate dice rolls
Random random = new Random(123); // Using a seed for controlled results
for (int i = 0; i < rolls; i++) {
int sum = 0;
for (int j = 0; j < 4; j++) {
int roll = random.nextInt(6) + 1; // Generate random number between 1 and 6 (inclusive)
sum += roll;
}
results[i] = sum;
}
// Count occurrences using an array
int[] countsArray = new int[21]; // Index 0 represents 4, index 20 represents 24
for (int result : results) {
countsArray[result - 4]++; // Increment count at the corresponding index
}
// Print statistical results using array
System.out.println("Results using array:");
for (int i = 0; i < countsArray.length; i++) {
int point = i + 4;
int count = countsArray[i];
System.out.println("Point " + point + ": " + count + " occurrences");
}
// Count occurrences using Map interface
Map<Integer, Integer> countsMap = new HashMap<>();
for (int result : results) {
countsMap.put(result, countsMap.getOrDefault(result, 0) + 1); // Increment count for the result
}
// Print statistical results using Map
System.out.println("\nResults using Map:");
for (Map.Entry<Integer, Integer> entry : countsMap.entrySet()) {
int point = entry.getKey();
int count = entry.getValue();
System.out.println("Point " + point + ": " + count + " occurrences");
}
}
}
(a) To control the random numbers to appear in the same order every time, we can use a seed value for the Random object. In the code above, Random random = new Random(123); sets the seed value to 123. Using the same seed value ensures that each time the program is executed, the generated random number sequence will be the same.
(b) To ensure that the random numbers appear in a different order every time, we can use the current time as the seed value for the Random object. In the code above, Random random = new Random(); uses the default constructor, which automatically uses the current time as the seed. This ensures that each time the program is executed, the generated random number sequence will be different.
(c) The code provided includes the counting of occurrences using an array (countsArray) to store the counts for each point (4 to 24). The results are printed out in the "Results using array" section.
(d) The code also includes the counting of occurrences using the Map interface (countsMap). The Map stores the point as the key and the count as the value. The results are printed out in the "Results using Map" section.
Learn more about Java:
https://brainly.com/question/19271625
#SPJ11
Discuss the importance of computer applications in Agricultural
and Biosystems Engineering.
In Agricultural and Biosystems Engineering, computer applications play an essential role in improving productivity, efficiency, and sustainability in food production and environmental protection. Here are some of the significant ways computer applications are important in Agricultural and Biosystems Engineering:
1. Precision Agriculture: Precision agriculture is a farming management concept that uses information technology to optimize production by minimizing waste and maximizing yield. It involves using various technologies such as GPS, remote sensing, soil analysis, and computer modeling to gather and analyze data about crop yields, soil characteristics, and weather patterns. This information is used to develop precise and efficient methods for planting, harvesting, fertilizing, and irrigating crops. Computer applications such as geographic information systems (GIS), computer modeling, and data analysis software are crucial to the success of precision agriculture.
2. Farm Automation and Robotics: Farm automation and robotics have become increasingly popular in modern farming practices. Computer applications such as artificial intelligence, machine learning, and computer vision are being used to develop autonomous machines that can perform tasks such as planting, harvesting, and weeding with minimal human intervention. These machines use sensors and cameras to identify crops and weeds and make decisions based on predetermined algorithms. Automation and robotics help reduce labor costs, increase efficiency, and minimize environmental impacts.
3. Environmental Protection: Computer applications are essential in developing sustainable farming systems that minimize environmental impacts. Biosystems engineers use computer models to simulate various scenarios and predict the effects of different farming practices on the environment. For example, computer models can be used to simulate the effects of different irrigation methods on water usage and soil erosion. These simulations help engineers develop sustainable farming practices that protect the environment while maximizing productivity.
4. Data Management and Analysis: In Agricultural and Biosystems Engineering, computer applications are used to manage and analyze vast amounts of data. This data is used to monitor crop growth, soil health, weather patterns, and other factors that affect agricultural productivity. Data management and analysis software are essential for interpreting this data and making informed decisions about farming practices. Computer applications such as databases, data mining software, and statistical analysis software are crucial for effective data management and analysis.
To learn more about biosystems engineering visit :
https://brainly.com/question/32677793
#SPJ11
(b) (10 pts.) Consider a linear time-invariant system with H(e) = tude response |H(ejw)|. 1+e-jw (1-ae-jw)2 Determine the magni- 1000/101100² 5b. a = 6
The magnitude of the frequency response for the given linear time-invariant system can be calculated by substituting the value of an (a=6) into the expression. The magnitude of the frequency response will be 1000/101100².
To calculate the magnitude of the frequency response |H(e^jω)|, we substitute the given expression H([tex]e^jω[/tex]) = (1+[tex]e^(-jω)[/tex])[tex](1-a*e^(-jω))^2[/tex] into the equation and then evaluate the magnitude.
Given a=6, we substitute a=6 into the expression:
H([tex]e^jω[/tex]) = (1+[tex]e^(-jω)[/tex])[tex](1-6*e^(-jω))^2[/tex]
Next, we calculate the magnitude by evaluating the absolute value of the expression:
|H([tex]e^jω[/tex])| = |(1+[tex]e^(-jω)[/tex])[tex](1-6*e^(-jω))^2[/tex]
By substituting the value of a=6 into the expression and simplifying the calculations, we find that the magnitude of the frequency response is 1000/101100².
In summary, by substituting the value of a=6 into the given expression for the frequency response, we determine the magnitude of the frequency response to be 1000/101100².
Learn more about time-invariant system here:
https://brainly.com/question/31041284
#SPJ11
Consider the liquid-phase elementary reaction (k = 2.5 L/mol min): 2A - B A feed of pure A is available at 7 L/min and 0.7 mol/dmº. You have been asked to maximise the conversion that can be achieved for this reaction, using two reactors available on site. The two reactors are a 10 L PFR and a 5 L CSTR. (a) Determine the conversion that can be achieved if the reactors are positioned in parallel, with the feed flow being split 50:50. (b) Determine the conversion that can be achieved if the reactors are positioned in series, with the CSTR following the PFR. (c) Use appropriate sketches to demonstrate how you would expect the conversion to compare to your answer in part (b) if the CSTR were placed first. You are not expected to do any calculations.
When the reactors are positioned in parallel and the feed flow is split 50:50, the total reactor volume is the sum of the volumes of the PFR and CSTR (10 L + 5 L = 15 L).
The conversion achieved in each reactor will be the same, and we can calculate it using the given rate constant and feed conditions. When the reactors are positioned in series, with the CSTR following the PFR, the conversion achieved will depend on the operating conditions and the volumes of the reactors. The PFR will achieve a higher conversion compared to the CSTR due to its plug-flow behavior and longer residence time. If the CSTR were placed first in the series configuration, the conversion achieved in the overall system would be lower compared to the case where the PFR is placed first.
To know more about flow click the link below:
brainly.com/question/30505507
#SPJ11
Discuss the voltage discharge in bit line and methods to limit the bit line voltage discharge?
Voltage discharge in bit lines is a common issue in digital memory systems that can lead to data loss and reliability problems. To mitigate this problem, several methods can be employed to limit the bit line voltage discharge.
Voltage discharge in bit lines refers to the gradual decrease in voltage levels that occurs over time. This phenomenon can be caused by various factors such as leakage currents, parasitic capacitances, and resistive effects in the memory cell and interconnects. If not properly addressed, voltage discharge can result in unreliable data loss and retrieval.
To limit the bit line voltage discharge, several techniques can be implemented. One approach is to use sense amplifiers, which are specialized circuits that amplify small voltage differences between the bit line and a reference voltage. By boosting the voltage levels, sense amplifiers can compensate for the discharge and restore the signal integrity.
Another method is to employ precharging techniques. Precharging involves setting the bit line to a predefined voltage level before accessing or reading the memory cell. This helps restore the initial voltage levels and minimize discharge effects.
Additionally, power supply techniques can be utilized to minimize voltage discharge. Power gating, for example, involves selectively shutting down power to idle memory cells or peripheral circuitry, reducing leakage currents and mitigating discharge.
By combining these approaches and optimizing circuit design, it is possible to limit the bit line voltage discharge, ensuring reliable operation and data integrity in digital memory systems.
Learn more about data loss here:
https://brainly.com/question/31595444
#SPJ11
EMC Facilities is important to determine the EMI/EMC level of a particular electronic device in order to ensure that it will be able to operate in its intended environment without having EMC problem. a. An OATS is alternative EMC facilities as compare with TEM and GTEM cell. Discuss the disadvantages of the OATS as compare with Semi-Anechoic Chamber and Reverberation Chamber. (6 marks) b. Absorber is designed specifically for use in Full/Semi-Anechoic chamber. Describe the different type of absorbers.
An Open Area Test Site (OATS) is an alternative EMC facility to TEM and GTEM cells. However, OATS has several disadvantages compared to Semi-Anechoic Chambers and Reverberation Chambers.
OATS is an outdoor facility that relies on open space for testing. The main disadvantages include the susceptibility to environmental conditions such as weather, ambient noise, and unwanted reflections from surrounding objects. These factors can introduce variability in the test results and make it difficult to achieve accurate and repeatable measurements. Additionally, OATS requires extensive setup and calibration to create a controlled test environment, which can be time-consuming and costly compared to the controlled indoor environments provided by Semi-Anechoic Chambers and Reverberation Chambers. Absorbers are essential components designed specifically for use in Full or Semi-Anechoic Chambers to control the reflections of electromagnetic waves. Different types of absorbers include pyramidal absorbers, ferrite tile absorbers, and hybrid absorbers. Pyramidal absorbers are made of carbon-loaded foam or rubber and are effective in absorbing electromagnetic energy across a wide frequency range. Ferrite tile absorbers, on the other hand, are used at lower frequencies and are composed of ferrite material.
Learn more about Open Area Test Site (OATS) here:
https://brainly.com/question/32716127
#SPJ11
Question Three Using the Ellingham diagram provided in the lecture notes, estimate the PO₂ eq. for the following reaction at 1000, 1200, 1400 and 1600 °C 4/3Cr + O₂ = 2/3Cr2O3
Using the Ellingham diagram, the estimated equilibrium partial pressure of oxygen (PO₂ eq.) for the reaction 4/3Cr + O₂ = 2/3Cr2O3 at temperatures of 1000, 1200, 1400, and 1600 °C are determined.
The Ellingham diagram is a graphical representation that provides information about the thermodynamic stability of metal oxides at different temperatures. By analyzing the diagram, we can estimate the equilibrium partial pressure of oxygen (PO₂ eq.) for a given reaction.
For the reaction 4/3Cr + O₂ = 2/3Cr2O3, we start by locating the relevant species on the Ellingham diagram. Chromium (Cr) and chromium(III) oxide (Cr2O3) are the compounds involved.
At each temperature (1000, 1200, 1400, and 1600 °C), we draw a line representing the standard Gibbs free energy change (ΔG°) for the reaction. The point at which this line intersects with the Cr-Cr2O3 equilibrium line gives us the equilibrium PO₂ eq. for the reaction at that temperature.
By following this procedure, we can estimate the PO₂ eq. for the reaction at 1000, 1200, 1400, and 1600 °C. The values obtained will depend on the specific Ellingham diagram used and the accuracy of the diagram itself.
Learn more about thermodynamic stability here:
https://brainly.com/question/27810737
#SPJ11
E. Refer to Figure 5. The single-phase "exact"-equivalent circuit of a practical transformer has the following equivalent circuit parameters: N p
/N s
=2400 V/240 V,R p
=14.1Ω,X p
= 31.2Ω,R s
=78.5 mΩ,X s
=120.5 mΩ,R C
=156kΩ,X M
=172kΩ. The load is a resistor with a value of R L
=1.95Ω. The source voltage is 2400∠30 ∘
V. 26. Determine the Thevenin impedance "seen" by the source. 27. Determine the source current I I
. 28. Determine the voltage E P
. 29. Determine the voltage V L
. 30. Determine the complex power delivered by the source. 31. Determine the RMS value of the transformer's magnetizing current. 32. Determine the core loss of the transformer. 33. Determine the copper losses of the transformer. 34. Determine the transformer's efficiency. 35 . Determine the transformer's voltage regulation using R L
as the full load condition.
The given problem involves determining various parameters of a practical transformer based on its equivalent circuit parameters and load conditions. The parameters to be calculated include the Thevenin impedance seen by the source.
To calculate the Thevenin impedance seen by the source, we need to consider the parallel combination of the primary winding impedance (Rp + jXp) and the magnetizing reactance (jXm).
The source current can be determined by dividing the source voltage (2400∠30° V) by the Thevenin impedance.
The voltage across the primary winding (Ep) can be found by subtracting the voltage drop across the series combination of Rp and Xp from the source voltage.
The voltage across the load (VL) can be determined using the voltage division principle by considering the impedance of the load resistor (RL) in parallel with the secondary winding impedance (Rs + jXs).
Learn more about equivalent circuit parameters here:
https://brainly.com/question/31965798
#SPJ11
For the FM signal given by, y(t) = 1000 cos (2π10²t + H cos(2710¹t)), where the value of H is 2.9 find the peak frequency deviation. Express your answer as a number in kHz. Do not add the units!
FM signal is given by [tex]y(t) = 1000 cos (2π10²t + H cos(2710¹t))[/tex], where the value of H is 2.9. The FM signal modulates the carrier wave and H is called the modulation index.
Frequency Modulation (FM) is a type of modulation in which the frequency of the carrier wave is varied in accordance with the modulating signal's amplitude and frequency. The peak frequency deviation can be determined by the expression :Peak frequency deviation = modulation index × frequency deviation According to the given values, [tex]f = 10^2 Hz and H = 2.9[/tex]
Therefore, we need to compute the frequency deviation or Δf. For that we can make use of Bessel's formula which is as follows:Bessel’s formula:
[tex]J0(H) = 1 + [(2/π)∑(m=1 to infinity)(-1)^m (H^2m) / (m!(2m)!)].Here, H = 2.9So, J0(2.9) = 1 + [(2/π) ∑(m=1 to infinity)(-1)^m (2.9^2m) / (m!(2m)!)].[/tex]
By computing the first five terms, we get:
[tex]J0(2.9) = 1 + 0.0546 - 0.000353 + 0.00000133 - 0.00000000349 +...J0(2.9) = 1.05524.[/tex]
The frequency deviation is [tex]Δf = (Hfmax)/J0(2.9)[/tex], where fmax is the maximum frequency deviation that is equal to the frequency of the carrier signal.
To know more about signal visit:
https://brainly.com/question/31473452
#SPJ11