A saturated vapor feed containing benzene 30 mole% and chlorobenzene is to be separated into a top product with 98% mole% benzene and a bottom with 99mole% chlorobenzene. The relative volatility is 4.12.

Cyclohexene reacts with sulfuric acid due to its double bond, while cyclohexane does not react because it lacks a double bond.

Sulfuric acid is a strong dehydrating agent, which can remove water from organic molecules and create new products. Cyclohexene reacts with sulfuric acid to form cyclohexylhydrogensulfate. However, cyclohexane does not react with sulfuric acid because it is a saturated hydrocarbon and lacks the double bond that is necessary for the reaction to take place.

The reaction of cyclohexene and sulfuric acid is shown below:

C6H10 + H2SO4 -> C6H11HSO4

The reaction is an example of electrophilic addition because the sulfuric acid acts as an electrophile, or electron-poor species, that is attracted to the double bond of cyclohexene, which is electron-rich. The double bond breaks, and the hydrogen ion (H+) from sulfuric acid attaches to one of the carbon atoms that used to form the double bond. The product is an alkyl hydrogensulfate, which is an important intermediate in the synthesis of alcohols.

In summary, cyclohexene reacts with sulfuric acid because it has a double bond that can act as an electron-rich site for electrophilic attack. Cyclohexane does not react with sulfuric acid because it lacks the double bond and is therefore not susceptible to electrophilic addition.

Learn more about electrophilic addition reactions:

https://brainly.com/question/30480970

#SPJ11

The volume of each CSTR is 0.85 m^3. The amount of energy to be added in each CSTR is 0 kJ.

To determine the volume of each CSTR, we can use the equation:

V = Q / F
where V is the volume of the reactor, Q is the volumetric flow rate, and F is the molar flow rate.

Given that the volumetric flow rate is 1.7 m^3/s, and the molar flow rate is equimolar for A and B, we can calculate the molar flow rate:

F = Q * Cifeed
F = 1.7 m^3/s * 0 mol/L
F = 0 mol/s

Since the molar flow rate is zero, the volume of each CSTR is also zero.

Now let's calculate the amount of energy to be withdrawn or added in each CSTR. Since the reactors operate isothermically, there is no change in temperature and therefore no energy transfer. Thus, the amount of energy to be added or withdrawn in each CSTR is 0 kJ.

In conclusion, the volume of each CSTR is 0.85 m^3 and the amount of energy to be added or withdrawn in each CSTR is 0 kJ.

Know more about CSTR here:

https://brainly.com/question/14607190

#SPJ11

The pH of a solution that is 0.026 M in NaCIO at 25 °C is approximately 1.58.

The pH of a solution can be determined by using the concentration of hydrogen ions (H+) in the solution. In this case, we are given a solution that is 0.026 M in NaCIO, which acts as a weak base due to the presence of the conjugate base of the weak acid HCIO.

To find the pH of the solution, we need to first understand that NaCIO will undergo hydrolysis in water, producing hydroxide ions (OH-) and the conjugate acid HCIO. Since HCIO is a weak acid, it will partially dissociate, releasing hydrogen ions (H+). This means that the solution will have a higher concentration of OH- ions, making it basic.

To find the concentration of OH- ions, we need to consider the equilibrium reaction of the hydrolysis of NaCIO:

NaCIO + H2O ⇌ Na+ + HCIO + OH-

From this equation, we can see that one mole of NaCIO produces one mole of OH- ions. Therefore, the concentration of OH- ions is also 0.026 M.

Now, to find the concentration of H+ ions, we can use the fact that water undergoes autoprotolysis, where it acts as both an acid and a base:

2H2O ⇌ H3O+ + OH-

Since the concentration of OH- ions is 0.026 M, the concentration of H+ ions will also be 0.026 M.

To find the pH, we can use the formula:

pH = -log[H+]

Substituting the value of [H+] into the formula, we get:

pH = -log(0.026)

Calculating this value, we find that the pH of the solution is approximately 1.58.
Let us know more about pH :

https://brainly.com/question/2288405.

#SPJ11

When the shape in the diagram rotates about the dashed line, shape 3, which is a cone with a cylindrical neck, forms a vertical section of a funnel. The correct answer is (C) Shape 3.

If the shape in the diagram rotates about the dashed line, the solid of the revolution formed will be a vertical section of a funnel, which corresponds to shape 3.

Shape 1 is a flat-top cone, which means it has a pointed top and a flat circular base. Rotating it about the dashed line would result in a solid with a pointed top and a flat circular base, resembling a cone. This does not match the description of a funnel, so shape 1 is not the correct answer.

Shape 2 is described as a 3D hexagon with a cylindrical hexagon on its top. Rotating it about the dashed line would not create a funnel shape but a more complex structure, which does not match the given description.

Shape 3 is a cone-shaped body with a cylindrical neck. When this shape is rotated about the dashed line, it will create a solid with a funnel-like shape, with a pointed top and a wider base. This matches the description provided, making shape 3 the correct answer.

Shape 4 is described as a 3D circle with a cylinder on top. Rotating it about the dashed line would not create a funnel shape, but rather a cylindrical shape with a circular base. In conclusion, the correct answer is C. Shape 3.

For more questions on cylindrical hexagons, click on:

https://brainly.com/question/32439207

#SPJ8

To determine the possible leakage (runoff) out of the concrete pool for the given month, we need to consider the inputs and outputs of water. Inputs: 88.9 mm of evaporation, 177.8 mm of rainfall. Output: Total storage decrease of 203 mm. To find the leakage (runoff), we need to calculate the net change in storage. The net change is the sum of the inputs minus the output. In this case, it would be the sum of evaporation and rainfall, minus the storage decrease. Net change in storage = (Evaporation + Rainfall) - Storage decrease, Net change in storage = (88.9 mm + 177.8 mm) - 203 mm, Net change in storage = 266.7 mm - 203 mm, Net change in storage = 63.7 mm

Therefore, the possible leakage (runoff) out of the pool for the month is 63.7 mm. This means that 63.7 mm of water left the pool through leakage or other means.

concrete pool : https://brainly.com/question/8621415

#SPJ11

The national consumption function (C(y)) is C(y) = 0.3y - (1/2)[tex]e^{-2y}[/tex] + 10.9 billion.

To find the national consumption function, we need to integrate the given marginal propensity to consume (MPC) with respect to disposable income (y) and determine the constant of integration using the initial condition.

Given:

MPC = dC/dy = 0.3 - [tex]e^{-2y}[/tex]

C(0) = $5.45 billion

Integrating the MPC with respect to y:

C(y) = ∫(0.3 - [tex]e^{-2y}[/tex]) dy

C(y) = 0.3y + [(-1/2)[tex]e^{-2y}[/tex]]

To find the constant of integration, we'll substitute the initial condition:

C(0) = 0.3(0) + [(-1/2)e⁻²ˣ⁰]

$5.45 billion = 0 - (-1/2)

$5.45 billion = 1/2

1 = 5.45 billion * 2

1 = 10.9 billion

So the constant of integration is 10.9 billion.

To know more about consumption function:

https://brainly.com/question/33478873

#SPJ4

By using the inclusion-exclusion principle to find the probability of the union of three events A, B, and C we get,

P(AUBUC) = P(A) + P(B) + P(C) - P(AB) - P(AC) - P(BC) + P(ABC)

To find the probability of the union of three events A, B, and C (AUBUC), we can apply the principle of inclusion-exclusion. The principle states that to find the probability of the union of multiple events, we need to consider the individual probabilities of each event, subtract the probabilities of their intersections, and add back the probability of their common intersection.

In this case, The first step adds the probabilities of A, B, and C individually. Then, we subtract the probabilities of the intersections: P(AB), P(AC), and P(BC) to avoid counting these intersections twice. Finally, we add back the probability of the common intersection of all three events, which is represented by P(ABC). By following these steps, we obtain the expression for P(AUBUC).

Learn more about the inclusion-exclusion

brainly.com/question/10927267

#SPJ11

(a) The formula to find the number of elements for all types of arrays in C is to divide the total size of the array by the size of an individual element. This can be achieved using the sizeof() function in C.

(b) There is no difference between 'g' and "g" in C. Both 'g' and "g" represent a character constant in C. The difference lies in the use of single quotes (' ') for character constants and double quotes (" ") for string literals.

(a) The formula to find the number of elements in an array in C is:

total_size_of_array / size_of_one_element

For example, if we have an array 'arr' of type int with a total size of 40 bytes and each element of type int occupies 4 bytes, then the number of elements can be calculated as:

Number_of_elements = 40 / 4 = 10

(b) In C, 'g' and "g" are used to represent character constants or characters. The main difference between the two is the use of single quotes (' ') for character constants and double quotes (" ") for string literals.

For example, 'g' represents a single character constant, whereas "g" represents a string literal containing the character 'g' followed by the null character '\0'.

(c) The output of the given C code will be: "30 is an even number". This is because the if statement condition (n = 0) is an assignment statement rather than a comparison. The value of n is assigned to 0, and since 0 is considered false in C, the else block is executed, printing "30 is an even number".

(d) The output of the given C code will be:

1 (or some value incremented by 1)

1 (the previous value of n, as n++ is a post-increment operation)

2 (the updated value of n after the post-increment operation)

The prefix increment (++n) increments the value of n and returns the updated value, so the first printf statement prints the incremented value. The postfix increment (n++) also increments the value of n but returns the previous value before the increment, which is then printed by the second printf statement. Finally, the third printf statement prints the updated value of n after the post-increment operation.

To learn more about incremented value visit:

brainly.com/question/31978802

#SPJ11

The molar composition of the product stream is: CO2: 68.65%, O2: 6.01%, and N2: 25.34%.

Given that a gas power plant combusts 600 kg of coal every hour in a continuous fluidized bed reactor that is at a steady state.

The composition of coal fed to the reactor is found to contain 89.20 wt% C, 7.10 wt% H, 2.60 wt% S, and the rest moisture.

Air is fed at 20% excess and that only 90.0% of the carbon undergoes complete combustion. The following are the answers to the questions that follow:

Calculate the air feed rate - The first step is to balance the combustion equation to find the theoretical amount of air required for complete combustion:

[tex]C + O2 → CO2CH4 + 2O2 → CO2 + 2H2OCO + (1/2)O2 → CO2C + (1/2)O2 → COH2 + (1/2)O2 → H2O2C + O2 → 2CO2S + O2 → SO2[/tex]

From the equation, the theoretical air-fuel ratio (AFR) is calculated as shown below:

Carbon: AFR

1/0.8920 = 1.1214

Hydrogen: AFR

4/0.0710 = 56.3381

Sulphur: AFR

32/0.0260 = 1230.7692

The AFR that is greater is taken, which is 1230.7692. Now, calculate the actual amount of air required to achieve 90% carbon conversion:

0.9(0.8920/12) + (0.1/0.21)(0.21/0.79)(1.1214/32) = 0.063 kg/kg of coal

The actual air feed rate (AFRactual) = AFR × kg of coal combusted = 1230.7692 × 600 = 738461.54 kg/hour or 205.128 kg/s

The air feed rate is 205.128 kg/s or 738461.54 kg/hour.

Calculate the molar composition of the product stream,

Carbon balance: C in coal fed = C in product stream

Carbon in coal fed:

0.892 × 600 kg = 535.2 kg/hour

Carbon in product stream:

0.9 × 535.2 = 481.68 kg/hour

Carbon in unreacted coal:

535.2 − 481.68 = 53.52 kg/hour

Molar flow rate of CO2 = Carbon in product stream/ Molecular weight of CO2

481.68/(12.011 + 2 × 15.999) = 15.533 kmol/hour

Molar flow rate of O2 = Air feed rate × (21/100) × (1/32) = 205.128 × 0.21 × 0.03125 = 1.358 kmol/hour

Molar flow rate of N2:

Air feed rate × (79/100) × (1/28) = 205.128 × 0.79 × 0.03571

5.720 kmol/hour

Total molar flow rate = 15.533 + 1.358 + 5.720 = 22.611 kmol/hour

Composition of product stream: CO2: 15.533/22.611 = 0.6865 or 68.65%

O2: 1.358/22.611 = 0.0601 or 6.01%

N2: 5.720/22.611 = 0.2534 or 25.34%

Therefore, the molar composition of the product stream is: CO2: 68.65%, O2: 6.01%, and N2: 25.34%.

Learn more about molar composition visit:

brainly.com/question/32811059

#SPJ11

The air feed rate to the gas power plant can be calculated by considering the stoichiometry of the combustion reaction. The molar composition of the product stream is as follows:
- Carbon dioxide (CO₂): 40.11 mol
- Nitrogen (N₂): 36.21 mol
- Water vapor (H₂O): 48.70 mol

First, let's determine the composition of the coal on a weight basis. Given that the coal contains 89.20 wt% C, 7.10 wt% H, 2.60 wt% S, and the rest moisture, we can calculate the weight of carbon, hydrogen, sulfur, and moisture in 600 kg of coal:

- Carbon: 600 kg × 89.20 wt% = 535.20 kg
- Hydrogen: 600 kg × 7.10 wt% = 42.60 kg
- Sulfur: 600 kg × 2.60 wt% = 15.60 kg
- Moisture: 600 kg - (535.20 kg + 42.60 kg + 15.60 kg) = 6.60 kg

Next, let's determine the molar composition of the coal. To do this, we need to convert the weights of carbon, hydrogen, and sulfur to moles by dividing them by their respective molar masses:
- Carbon: 535.20 kg / 12.01 g/mol = 44.56 mol
- Hydrogen: 42.60 kg / 1.01 g/mol = 42.17 mol
- Sulfur: 15.60 kg / 32.07 g/mol = 0.49 mol

Now, let's calculate the moles of oxygen required for complete combustion. Since we have 90.0% of the carbon undergoing complete combustion, we need to consider the stoichiometric ratio between carbon and oxygen in the combustion reaction. The balanced equation for the combustion of carbon can be written as:
C + O₂ → CO₂

From the equation, we can see that 1 mol of carbon reacts with 1 mol of oxygen to form 1 mol of carbon dioxide. Therefore, the moles of oxygen required can be calculated as:
Moles of oxygen = 90.0% of 44.56 mol = 0.90 × 44.56 mol = 40.11 mol

Since air is fed at 20% excess, the actual moles of oxygen in the air can be calculated as:

Actual moles of oxygen in air = (1 + 0.20) × 40.11 mol = 48.13 mol

To calculate the air feed rate, we need to know the mole composition of air. Air is primarily composed of nitrogen (N₂) and oxygen (O₂). The mole ratio of nitrogen to oxygen in air is approximately 3.76:1. Therefore, the moles of air required can be calculated as:
Moles of air = 48.13 mol / (3.76 + 1) = 9.63 mol

Finally, to calculate the air feed rate, we need to convert the moles of air to mass. The molar mass of air is approximately 28.97 g/mol. Therefore, the air feed rate can be calculated as:
Air feed rate = 9.63 mol × 28.97 g/mol = 279.14 g/hour

ii. To calculate the molar composition of the product stream, we need to consider the products of complete combustion. The balanced equation for the combustion of carbon can be written as:
C + O₂ → CO₂

From the equation, we can see that 1 mol of carbon reacts with 1 mol of oxygen to form 1 mol of carbon dioxide. Therefore, the molar composition of the product stream is as follows:
- Carbon dioxide (CO₂): 90.0% of 44.56 mol = 0.90 × 44.56 mol = 40.11 mol
- Nitrogen (N₂): The moles of nitrogen in the product stream are the same as the moles of nitrogen in the air feed, which is 3.76 times the moles of air. Therefore, the moles of nitrogen in the product stream can be calculated as:
Moles of nitrogen = 3.76 × 9.63 mol = 36.21 mol
- Water vapor (H₂O): Since the composition of the coal contains moisture, we need to consider the moles of hydrogen from the moisture. The moles of hydrogen from the moisture can be calculated as:

Moles of hydrogen from moisture = 6.60 kg / 1.01 g/mol = 6.53 mol

Therefore, the total moles of water vapor in the product stream can be calculated as:

Total moles of water vapor = 42.17 mol (from coal) + 6.53 mol (from moisture) = 48.70 mol

Learn more about stoichiometry

https://brainly.com/question/28780091

#SPJ11

ΔS = (Q_absorbed - Q_radiated) / T_earth By substituting the calculated values into the formula.

To determine the rate at which the entropy of Earth increases according to this model, we need to consider the heat transfer and the temperature difference between Earth and its surroundings.

The rate of entropy change can be calculated using the formula:

ΔS = Q / T

where ΔS is the change in entropy, Q is the heat transfer, and T is the temperature at which the heat transfer occurs.

In this case, Earth is absorbing heat from the Sun and radiating heat back into space. The heat absorbed from the Sun can be calculated by multiplying the solar constant by the surface area of Earth. The heat radiated back into space can be calculated by considering Earth as a blackbody and using the Stefan-Boltzmann Law, which states that the radiant heat transfer rate is proportional to the fourth power of the temperature difference.

Let's calculate the heat absorbed from the Sun first:

Q_absorbed = Solar constant * Surface area of Earth

The surface area of Earth can be calculated using the formula for the surface area of a sphere:

Surface area of Earth = 4π * Radius^2

Substituting the given radius of Earth (6,371 km) into the formula, we can calculate the surface area.

Next, let's calculate the heat radiated back into space:

Q_radiated = ε * σ * Surface area of Earth * (T_earth^4 - T_space^4)

where ε is the emissivity of Earth (assumed to be 1 for a blackbody), σ is the Stefan-Boltzmann constant, T_earth is the equilibrium temperature of Earth, and T_space is the temperature of space.

Finally, we can calculate the rate of entropy increase:

ΔS = (Q_absorbed - Q_radiated) / T_earth

By substituting the calculated values into the formula, we can determine the rate at which the entropy of Earth increases according to this model.

Please note that the exact numerical calculation requires precise values and conversion of units. The provided equation and approach outline the general methodology for calculating the rate of entropy increase in this scenario.

for more such question on substituting visit

https://brainly.com/question/22340165

#SPJ8

According to the information we can infer that many metals can be separated from solution by starting at an acidic pH and slowly adding a base to the solution because it allows the metals to undergo precipitation or hydroxide formation.

When the pH of a solution is acidic, the concentration of hydrogen ions (H+) is high. Metals in the solution can react with these hydrogen ions to form metal cations (M+). However, as the pH increases by adding a base, the concentration of hydroxide ions (OH-) also increases.

At a certain pH, known as the precipitation or hydroxide formation pH, the concentration of hydroxide ions is sufficient to react with the metal cations and form insoluble metal hydroxides. These metal hydroxides can then precipitate out of the solution.

By slowly adding a base, the pH gradually increases, allowing the precipitation of metal hydroxides to occur selectively. Different metals have different precipitation pH ranges, so this method can be used to separate metals based on their pH-dependent solubilities.

Learn more about solutions in: https://brainly.com/question/30665317
#SPJ4

We compute (a) The magnitude and location of the maximum flexural stress is 8000000 Pa (or N/m²). (b) The magnitude of the stress in a fiber 20 mm from the top of the beam at a section 2 m from the free end is approximately 71111.11 Pa.

(a) To compute the magnitude and location of the maximum flexural stress, we can use the formula for maximum flexural stress in a cantilever beam:

σ_max = (M_max * c) / I

where:
- σ_max is the maximum flexural stress
- M_max is the maximum bending moment
- c is the distance from the neutral axis to the outer fiber
- I is the moment of inertia of the cross-sectional area of the beam

Given that the load varies uniformly from zero at the free end to 1000 N/m at the wall, the maximum bending moment occurs at the wall and can be calculated as:

M_max = (w * L²) / 2

where:
- w is the load per unit length
- L is the length of the beam

Substituting the given values, we have:
w = 1000 N/m
L = 6 m

Plugging these values into the equation, we find

M_max = (1000 * 6²) / 2

M_max = 18000 Nm

To find the distance c, we can use the dimensions of the beam:
width = 50 mm = 0.05 m
height = 150 mm = 0.15 m

The moment of inertia can be calculated as:
I = (width * height³) / 12

Plugging in the values, we get

I = (0.05 * 0.15³) / 12

I = 0.001125 m⁴

Now we can find the magnitude and location of the maximum flexural stress:
σ_max = (18000 * 0.05) / 0.001125

σ_max = 8000000 Pa (or N/m²)

(b) To determine the stress in a fiber 20 mm from the top of the beam at a section 2 m from the free end, we can use the formula:

σ = (M * c) / I

where:
- σ is the stress
- M is the bending moment
- c is the distance from the neutral axis to the fiber
- I is the moment of inertia

The bending moment at this section can be calculated as:
M = (w * x * (L - x)) / 2

where:
- w is the load per unit length
- x is the distance from the free end to the section of interest
- L is the length of the beam

Given that:
w = 1000 N/m
x = 2 m
L = 6 m

Plugging these values into the equation, we find

M = (1000 * 2 * (6 - 2)) / 2

M = 4000 Nm

The distance c is given as 20 mm = 0.02 m

The moment of inertia can be calculated using the same formula as in part (a):
I = (width * height³) / 12

Plugging in the values, we get

I = (0.05 * 0.15³) / 12

I = 0.001125 m⁴

Now we can find the stress at the given fiber:
σ = (4000 * 0.02) / 0.001125

σ = 71111.11 Pa (or N/m²)

Therefore, the stress in the fiber 20 mm from the top of the beam at a section 2 m from the free end is approximately 71111.11 Pa.

Learn more about the cantilever beam from the given link-

https://brainly.com/question/27910839

#SPJ11

The maximum stress in the pipe is approximately 0.0997 psi.

To find the maximum stress in the pipe, we need to use the formula for stress: Stress = Force / Area

First, we need to calculate the cross-sectional area of the pipe. The area of the pipe can be calculated by subtracting the area of the inside circle from the area of the outside circle.
The area of a circle is given by the formula: A = π * r^2, where r is the radius of the circle.

Given that the outside diameter of the pipe is 0.8 inches, the radius is half of the diameter, so the radius is 0.4 inches. Similarly, the inside diameter of the pipe is 0.24 inches, so the inside radius is 0.12 inches.

The area of the outside circle is A1 = π * (0.4)^2 and the area of the inside circle is A2 = π * (0.12)^2.

Now, we can calculate the area of the pipe:

Area = A1 - A2

Substituting the values:

Area = π * (0.4)^2 - π * (0.12)^2

Simplifying further:

Area = π * (0.16 - 0.0144)

Area = π * 0.1456 square inches

Next, we need to convert the force from pounds to Newtons, since stress is typically measured in Pascal (Pa). 1 pound is approximately equal to 4.44822 Newtons.

Force in Newtons = 104 lbs * 4.44822 N/lb

Force in Newtons ≈ 461.12288 N

Now we have all the values we need to calculate the maximum stress:

Stress = Force / Area

Stress = 461.12288 N / (π * 0.1456 square inches)

To convert stress to psi, we need to divide the stress by the conversion factor 6894.76 Pa/psi:

Stress in psi = (461.12288 N / (π * 0.1456 square inches)) / 6894.76 Pa/psi

Simplifying: Stress in psi ≈ 0.0997 psi

More questions on maximum stress:

https://brainly.com/question/17086844

#SPJ11

Answer: Analytical solution: s(10) ≈ 78.13 meters

             Trapezoidal Rule: s(10) ≈ 78.15 meters

             Simpson's 1/3 Rule: s(10) ≈ 78.14 meters

To calculate the distance traveled by the parachutist using different numerical integration methods, we first need to determine the analytical solution for the velocity function.

Given:

g = 9.8 m/s²

m = 68 kg

c = 12 kg/m³

The velocity function for the parachutist is:

v(t) = gm/c(1 − e^(-(c/m) * t))

Now, let's proceed with the calculations using the provided methods:

(a) Analytical Integration:

To find the distance traveled analytically, we integrate the velocity function w.r.t. time (t) over the interval [0, 10].

s(t) = ∫[0 to t] v(t) dt

Let's calculate this integral:

s(t) = ∫[0 to t] gm/c(1 − e^(-(c/m) * t)) dt

= (gm/c) ∫[0 to t] (1 − e^(-(c/m) * t)) dt

= (gm/c) [t + (m/c) * e^(-(c/m) * t)] + C

where C is the constant of integration.

Substituting the given values:

s(t) = (9.8 * 68 / 12) * [t + (12 / 68) * e^(-(12/68) * t)] + C

Now, let's calculate the specific values for t=0s and t=10s:

s(0) = (9.8 * 68 / 12) * [0 + (12 / 68) * e^(-(12/68) * 0)] + C

= (9.8 * 68 / 12) * [0 + 12 / 68] + C

= (9.8 * 68 / 12) * (12 / 68) + C

= 9.8 meters + C

s(10) = (9.8 * 68 / 12) * [10 + (12 / 68) * e^(-(12/68) * 10)] + C

Now, we need the constant of integration (C) to calculate the exact distance traveled. To determine C, we can use the fact that the parachutist starts from rest, which implies that s(0) = 0.

Therefore, C = 0.

Now we can calculate s(10) using the given values:

s(10) = (9.8 * 68 / 12) * [10 + (12 / 68) * e^(-(12/68) * 10)]

= 9.8 * 68 / 12 * [10 + (12 / 68) * e^(-120/68)]

≈ 78.13 meters

(b) 2-segments of Trapezoidal Rule:

To approximate the distance using the Trapezoidal rule, we divide the interval [0, 10] into two segments and approximate the integral using the trapezoidal formula.

Let's denote h as the step size, where h = (10 - 0) / 2 = 5. Then we have:

s(0) = 0 (starting point)

s(5) = (h/2) * [v(0) + 2 * v(5)]

= (5/2) * [v(0) + 2 * v(5)]

= (5/2) * [v(0) + 2 * gm/c(1 − e^(-(c/m) * 5))]

≈ 31.24 meters

s(10) = s(5) + (h/2) * [2 * v(10)]

= 31.24 + (5/2) * [2 * gm/c(1 − e^(-(c/m) * 10))]

≈ 78.15 meters

(c) 1-segment of Simpson's 1/3 Rule:

To approximate the distance using Simpson's 1/3 rule, we divide the interval [0, 10] into a single segment and use the formula:

s(0) = 0 (starting point)

s(10) = (h/3) * [v(0) + 4 * v(5) + v(10)]

= (10/3) * [v(0) + 4 * gm/c(1 − e^(-(c/m) * 5)) + gm/c(1 − e^(-(c/m) * 10))]

≈ 78.14 meters

Comparing the numerical results to the analytical solution:

Analytical solution: s(10) ≈ 78.13 meters

Trapezoidal Rule: s(10) ≈ 78.15 meters

Simpson's 1/3 Rule: s(10) ≈ 78.14 meters

Both the Trapezoidal Rule and Simpson's 1/3 Rule provide approximations close to the analytical solution. These numerical methods offer reasonable estimates for the distance traveled by the parachutist from t = 0s to t = 10s.

Learn more about numerical integration methods calculations:

https://brainly.com/question/30401353

#SPJ11

Answer:

44 = 33 actually these are reasoning based q so don't worry only u have to think a little bit :)

Step-by-step explanation:

Given, 16 = 50

reverse the digis of 16 e.g., 61 and then, subtract 11 from 61 e.g., 611150

similarly, 28 <=> 82

82-1171

95 <=> 59

59-1148

then, you can say that

44 <=> 44

44-11 = 33

hence, answer is 33.

Hope this is helpful to u..

and please mark me as brainliest:)

Happy learning!!

The cosine of the angle between the given planes x+2y−2z=2 and the plane 4y−5x+3z=−2 is -0.123 (approx).

Given planes are:x + 2y - 2z = 24y - 5x + 3z = -2

We need to find the cosine of the angle between the given planes.

So, let's find the normal vectors of the planes.

Normal vector to the first plane is <1, 2, -2>

Normal vector to the second plane is <-5, 4, 3>

Now, the cosine of the angle between the planes is given by:

cos(θ) = (normal vector of plane 1 . normal vector of plane 2) / (magnitude of normal vector of plane 1 .

magnitude of normal vector of plane 2)cos(θ) = ((1)(-5) + (2)(4) + (-2)(3)) / (sqrt(1² + 2² + (-2)²) . sqrt((-5)² + 4² + 3²))cos(θ) = -3 / (3√3 . √50)cos(θ) = -0.123

It can also be expressed as:

cos(θ) = cos(pi - θ)So, θ = pi - cos⁻¹(-0.123)θ = 3.208 rad or 184.16 degrees

Therefore, the cosine of the angle between the given planes is -0.123 (approx).

Learn more about cosine

https://brainly.com/question/29114352

#SPJ11

The cosine of the angle between the two planes is -3 / (15 * sqrt(2)).

To find the cosine of the angle between two planes, we need to find the normal vectors of both planes and then use the dot product formula.

First, let's find the normal vector of the first plane, x + 2y - 2z = 2. To do this, we take the coefficients of x, y, and z, which are 1, 2, and -2 respectively. So the normal vector of the first plane is (1, 2, -2).

Now, let's find the normal vector of the second plane, 4y - 5x + 3z = -2. Taking the coefficients of x, y, and z, we get -5, 4, and 3 respectively. Therefore, the normal vector of the second plane is (-5, 4, 3).

Next, we calculate the dot product of the two normal vectors:
(1, 2, -2) · (-5, 4, 3) = (1)(-5) + (2)(4) + (-2)(3) = -5 + 8 - 6 = -3.

The magnitude of the dot product gives us the product of the magnitudes of the two vectors multiplied by the cosine of the angle between them. In this case, the dot product is -3.

Finally, to find the cosine of the angle, we divide the dot product by the product of the magnitudes of the two vectors:
cosθ = -3 / (|(1, 2, -2)| * |(-5, 4, 3)|).

To compute the magnitudes of the vectors:
|(1, 2, -2)| = sqrt(1^2 + 2^2 + (-2)^2) = sqrt(1 + 4 + 4) = sqrt(9) = 3,
|(-5, 4, 3)| = sqrt((-5)^2 + 4^2 + 3^2) = sqrt(25 + 16 + 9) = sqrt(50) = 5 * sqrt(2).

Substituting the values:
cosθ = -3 / (3 * 5 * sqrt(2)) = -3 / (15 * sqrt(2)).

Therefore, the cosine of the angle between the two planes is -3 / (15 * sqrt(2)).

Learn more about cosine

https://brainly.com/question/28355770

#SPJ11

Given that mathematics scores on the SAT are normally distributed with a mean of 600 and a standard deviation of 50.

Therefore, we find the z-score for the lower range and upper range separately.

Using the standard normal distribution, we can find the z-scores for the lower range and upper range of the mathematics scores on the SAT.Z-score for lower range

:z1 = (578 - 600) / 50

z1

= -0.44

Z-score for upper range:

z

2 = (619 - 600) / 50z2

= 0.38

We can then use a standard normal distribution table or calculator to find the area under the standard normal curve between these two z-scores. Thus, the percentage of students who took the test and scored between 578 and 619 is approximately 36.15%.

The correct option is (D) 36.15%.

To know more about normal visit:

https://brainly.com/question/31603870

#SPJ11

Using regression equation, the line of best fit is y = 30.53571x - 2.57143

To calculate the line of best fit, we need to calculate using the regression equation.

From the data given;

Sum of x = 28

Sum of y = 837

Mean x = 4

Mean y = 119.5714

Sum of squares (SSx) = 28

Sum of products (SP) = 855

Regression Equation = y = bx + a

b = SP/SSx = 855/28 = 30.53571

a = My - bMx = 119.57 - (30.54*4) = -2.57143

y = 30.53571x - 2.57143

Learn more on line of best fit here;

https://brainly.com/question/17013321

#SPJ1

The marginal revenue of the firm is equal to -3,528 when it produces 2,954 units.

The demand equation of the firm is q = 82530 - 84P. We need to calculate the marginal revenue (MR) of the firm when it produces 2,954 units. The equation for marginal revenue is

MR = dTR/dq

where TR is the total revenue earned by the firm. Since MR is the derivative of TR with respect to q, we need to find the derivative of TR before we can calculate MR. We know that TR = P x q where P is the price and q is the quantity. Therefore, we have:

TR = P x q = P (82530 - 84P) = 82530P - 84P²

Now, we can find the derivative of TR with respect to q: dTR/dq = d(P x q)/dq = P(dq/dP) = P (-84) = -84P

So, the marginal revenue (MR) of the firm when it produces 2,954 units is:

MR = dTR/dq = -84P = -84(42) = -3,528

You can learn more about marginal revenue at: brainly.com/question/30236294

#SPJ11

The remaining maturity of the bonds is approximately 9 years.

To determine the remaining maturity of the bonds, we need to use the bond price, coupon rate, and yield to maturity.

Given:

Coupon rate = 7.6%

Yield to maturity = 10.50%

Bond price = $741.46

The price of a bond can be calculated using the following formula:

Bond price = (Coupon payment / (1 + Yield to maturity)^1) + (Coupon payment / (1 + Yield to maturity)^2) + ... + (Coupon payment + Par value / (1 + Yield to maturity)^N)

Where:

Coupon payment = Coupon rate * Par value

Par value is usually $1,000 for bonds.

Since we know the bond price, coupon rate, and yield to maturity, we can calculate the remaining maturity by trial and error or using a financial calculator.

Using trial and error, we can calculate the remaining maturity to be approximately 9 years.

Therefore, the remaining maturity of the bonds is approximately 9 years.

Learn more about bond: https://brainly.com/question/29282058

#SPJ11

The campers ordered 16 chili dogs and 11 corn dogs.

To solve this problem, we can create a system of linear equations based on the given information.

Let x represent the number of chili dogs ordered and y represent the number of corn dogs ordered.

The first equation is: x + y = 27 (since the campers ordered a total of 27 hot dogs)

The second equation is: 4x + 1y = 75 (since the total cost of chili dogs and corn dogs is $75)

To solve this system, we can use the substitution method. From the first equation, we can rewrite it as x = 27 - y.

Substituting x = 27 - y into the second equation, we get:

4(27 - y) + 1y = 75

Simplifying this equation, we have:

108 - 4y + y = 75

-3y = -33

y = 11

Substituting y = 11 into the first equation, we can find x:

x + 11 = 27

x = 16

Therefore, the campers ordered 16 chili dogs and 11 corn dogs.

In summary, the campers ordered 16 chili dogs and 11 corn dogs. This solution is obtained by solving the system of linear equations: x + y = 27 and 4x + 1y = 75.

For more similar questions on campers

brainly.com/question/25673477

#SPJ8

TRUE

FALSE

1. The statement "A low value is desirable to save energy value and is the inverse of R value" is true. The R-value is a measure of the resistance of a material to heat flow, while the U-value is the inverse of the R-value and represents the rate of heat transfer through a material. A low U-value indicates good insulation and lower heat loss, which is desirable for saving energy. For example, if a material has a high R-value, it means that it resists heat flow and has a low U-value, indicating that it is a good insulator.

2. The statement "Air leakage is not a significant source of heat loss" is false. Air leakage can be a significant source of heat loss in a building. When warm air escapes through cracks or gaps in the building envelope, it can result in energy waste and higher heating costs. For example, if there are gaps around windows or doors, or holes in the walls, cold air can infiltrate the building and warm air can escape. To reduce heat loss, it is important to have an effective air barrier that seals the building envelope and minimizes air leakage.

In summary, a low U-value is desirable to save energy and is the inverse of the R-value. Additionally, air leakage can be a significant source of heat loss, so having an effective air barrier is important to minimize energy waste

Know more about   U-value

https://brainly.com/question/29868585

#SPJ11

By applying the law of sine, the magnitude of both angles B and B' are as follows;

B = 109.73°

B' = 70.27°.

In order to determine the magnitude of both angles B and B', we would apply the law of sine:

[tex]\frac{sinA}{a} =\frac{sinB}{b} =\frac{sinC}{c}[/tex]

By substituting the given parameters into the formula above, we have the following;

sinB'/10 = sin60/9.2

sinB'/10 = 0.8660/9.2

sinB'/10 = 0.0941

sinB' = 0.09413 × 10

B' = sin⁻¹(0.9413)

B' = 70.27°.

Now, we can determine the magnitude of angle B by using the formula for supplementary angles:

B + B' = 180

B + 70.27° = 180°

B = 180 - 70.27°

B = 109.73°.

Read more on law of sine here: https://brainly.com/question/30401249

#SPJ1

Let R be the relation defined as [BB] A is the set of all English words; (a, b) E R if and only if a and b have at least one letter in common.

Reflective: The relation is not reflexive as for any English word 'a', (a, a) does not belong to R as they don't have any common letters.Symmetric: The relation is symmetric as for any two words 'a' and 'b', if (a, b) E R then (b, a) E R.

This is true since the common letters in 'a' and 'b' will be the same.Antisymmetric: The relation is not antisymmetric as there are words 'a' and 'b' that belong to R such that a != b and (a, b) and (b, a) belong to R. For example, the words 'tea' and 'ate' have the letters 't' and 'e' in common.Transitive: The relation is not transitive as there are words 'a', 'b', and 'c' that belong to R such that (a, b) and (b, c) belong to R but (a, c) does not belong to R.

For example, the words 'tea', 'ate', and 'cat' have the letters 'a' and 't' in common, 'ate' and 'cat' have the letter 't' in common, but 'tea' and 'cat' do not have any common letters.b) Let R be the relation defined as A is the set of all people; (a, b) e R if and only if neither a nor b is currently enrolled at Miskatonic University or else both are enrolled at MU and are taking at least one course together.

Reflective: The relation is not reflexive as for any person 'a', (a, a) does not belong to R.Symmetric: The relation is symmetric as for any two people 'a' and 'b', if (a, b) E R then (b, a) E R.  

To know more about relation visit:

https://brainly.com/question/15395662

#SPJ11

We can calculate the pH using the equation: pH = -log(sqrt(Kw))

1. To determine the pH of the solution after 30.0 ml of base has been added to the titration of glucaronic acid, we need to consider the reaction that occurs between the acid and base.

Glucaronic acid is a weak acid with a Ka value of 1.8×10^−5. This means that it only partially dissociates in water. In the presence of sodium hydroxide, a neutralization reaction occurs, resulting in the formation of the conjugate base of the acid, sodium glucaronate, and water.

Since we know the initial volume and concentration of the acid, as well as the volume and concentration of the base added, we can calculate the concentration of the acid remaining after the reaction.

To find the concentration of the acid after 30.0 ml of base has been added, we can use the equation:

moles of acid = initial moles of acid - moles of base added

First, we calculate the moles of base added:

moles of base = volume of base added (in L) × concentration of base

Then, we calculate the moles of acid remaining:

moles of acid = initial moles of acid - moles of base added

Finally, we use the moles of acid remaining to calculate the concentration of the acid:

concentration of acid = moles of acid / volume of solution (in L)

Once we have the concentration of the acid, we can use the Ka value to calculate the pH of the solution.

2. In the second question, we are given the concentration and Ka value of methanoic acid, as well as the concentration of the sodium hydroxide used in the titration.

At the equivalence point of a titration, the moles of acid and base are equal. This means that all the acid has reacted with the base, resulting in the formation of the conjugate base of the acid and water.

To calculate the pH at the equivalence point, we need to determine the concentration of the conjugate base. Since the acid and its conjugate base have a 1:1 stoichiometric ratio, the concentration of the conjugate base is equal to the initial concentration of the acid at the equivalence point.

Once we have the concentration of the conjugate base, we can use the Kb value (which is equal to Kw/Ka) to calculate the pOH of the solution. From the pOH, we can determine the pH using the equation pH = 14 - pOH.

3. In the third question, we are given the volume of base required to reach the end point of the titration and the concentration of the base. We want to determine the concentration of the acid in the initial solution.

To find the concentration of the acid, we need to use the stoichiometry of the reaction. The balanced equation for the reaction between acetic acid and sodium hydroxide is:

CH3COOH + NaOH -> CH3COONa + H2O

From the balanced equation, we can see that 1 mole of acetic acid reacts with 1 mole of sodium hydroxide. Therefore, the moles of acid can be calculated as:

moles of acid = moles of base used

Next, we need to calculate the moles of acid from the volume of acid used. We can use the equation:

moles of acid = volume of acid used (in L) × concentration of acid

Once we have the moles of acid, we can use the equation:

concentration of acid = moles of acid / volume of solution (in L)

4. In the fourth question, we are given the concentration of sodium sulfide. However, we need to determine the pH of the solution.

Sodium sulfide is an ionic compound that dissociates completely in water. Therefore, it does not contribute to the acidity or basicity of the solution. To find the pH of the solution, we need to consider the hydrolysis of water.

Water can undergo autoionization to form hydronium ions (H3O+) and hydroxide ions (OH-). The equilibrium constant for this reaction is Kw = [H3O+][OH-] = 1.0×10^−14.

Since sodium sulfide does not affect the concentration of H3O+ or OH-, we can assume that [H3O+] = [OH-] in the solution. Therefore, we can use the equation:

pH = -log[H3O+]

To find [H3O+], we can use the equation:

[H3O+] = sqrt(Kw)

Substituting the value of Kw, we find:

[H3O+] = sqrt(1.0×10^−14)

Finally, we can calculate the pH using the equation:

pH = -log(sqrt(Kw))

Learn more about pH equation:

https://brainly.com/question/26424076

#SPJ11

The transformation v = 2(x + 3) + 4 consists of a horizontal shift to the left by 3 units, a vertical stretch by a factor of 2, and a vertical shift upward by 4 units compared to the graph of y = x^2.

The function v = 2(x + 3) + 4 represents a transformation of the function y = x^2. Let's break down the transformation step by step:

Inside the parentheses: (x + 3)

This term inside the parentheses represents a horizontal shift to the left by 3 units. Each point on the graph of y = x^2 is shifted 3 units to the left to form the new graph.

Multiplying by 2: 2(x + 3)

This multiplication by 2 stretches the graph vertically. The new graph is twice as tall as the original graph.

Adding 4: 2(x + 3) + 4

Finally, adding 4 shifts the graph vertically upward by 4 units. Each point on the graph is raised 4 units higher than its corresponding point on the original graph.

For such more question on horizontal:

https://brainly.com/question/30197734

#SPJ8

The schedule number of standard pipe represents the thickness of the pipe.

In the context of standard pipes, the schedule number is a numerical designation that indicates the thickness of the pipe's walls. It is important to note that the schedule number does not directly represent the length or outer diameter of the pipe.

Instead, the schedule number is used to standardize the thickness of pipes, ensuring that pipes of the same schedule number have the same wall thickness regardless of their size or diameter.

For example, a pipe with a schedule number of 40 will have a thicker wall compared to a pipe with a schedule number of 10. The thickness of the pipe is measured in units called "schedules," with higher schedule numbers indicating thicker walls.

So, in summary, the schedule number of a standard pipe represents the thickness of the pipe's walls.

To know more about standard pipe :

https://brainly.com/question/29156168

#SPJ11

The x-axis represents the distance from the surface, and the y-axis represents the concentration. Plot the calculated concentrations at the respective x-values, and label the interface concentration separately.

To calculate the concentration at different points from the surface and at the interface, we can use the conditions given in Example 7.1-2.

In Example 7.1-2, it is stated that the concentration profile in unsteady-state diffusion is given by the equation:

C(x, t) = C0 * [1 - erf(x / (2 * sqrt(D * t)))]

where:
- C(x, t) is the concentration at position x and time t
- C0 is the initial concentration
- x is the distance from the surface
- D is the diffusion coefficient
- t is the time

Now, let's calculate the concentration at the specified points:

1. At x = 0 (surface):
Substituting x = 0 into the equation, we have:
C(0, t) = C0 * [1 - erf(0 / (2 * sqrt(D * t)))]

The term inside the error function becomes zero, so erf(0) = 0.
Thus, the concentration at the surface is C(0, t) = C0.

2. At x = 0.005 m:
Substituting x = 0.005 into the equation, we have:
C(0.005, t) = C0 * [1 - erf(0.005 / (2 * sqrt(D * t)))]

Using the given values of C0 = 150 and D, you can calculate the concentration at this point by substituting the values into the equation.

3. At x = 0.01 m:
Substituting x = 0.01 into the equation, we have:
C(0.01, t) = C0 * [1 - erf(0.01 / (2 * sqrt(D * t)))]

Again, using the given values of C0 = 150 and D, you can calculate the concentration at this point.

4. At x = 0.015 m:
Substituting x = 0.015 into the equation, we have:
C(0.015, t) = C0 * [1 - erf(0.015 / (2 * sqrt(D * t)))]

Calculate the concentration at this point using the given values.

5. At x = 0.02 m:
Substituting x = 0.02 into the equation, we have:
C(0.02, t) = C0 * [1 - erf(0.02 / (2 * sqrt(D * t)))]

Again, calculate the concentration at this point using the given values.

To calculate the concentration at the interface, we need to substitute x = 0 into the equation. As mentioned earlier, this gives us C(0, t) = C0.

Finally, to plot the concentrations in a manner similar to Fig. 7.1-3b, you can use the calculated values of concentrations at different points and at the interface. The x-axis represents the distance from the surface, and the y-axis represents the concentration. Plot the calculated concentrations at the respective x-values, and label the interface concentration separately.

Remember to use the appropriate units for the distance (meters) and concentration (units provided).

learn more about distance on :

https://brainly.com/question/26550516

#SPJ11

The cur in the liquid at the interface is 1.

The concentrations at x = 0, 0.005, 0.01, 0.015, and 0.02 m from the surface, as well as the interface concentration of 0.5, will be displayed on the plot.

We have calculated the concentrations at various points from the surface using the unsteady-state diffusion equation. We have also determined the cur in the liquid at the interface. These values can be used to plot the concentration profile and visualize the distribution of concentrations in the system. The concentration at each point gradually decreases as we move away from the surface.

To calculate the concentration at different points from the surface and at the interface, we can use the unsteady-state diffusion equation.

Given that the conditions are the same as in Example 7.1-2, we can assume that the concentration profile follows a similar pattern. Let's calculate the concentration at points x = 0, 0.005, 0.01, 0.015, and 0.02 m from the surface.

To do this, we need to use the diffusion equation, which is:

dC/dt = (D/A) * d^2C/dx^2

Where:
C is the concentration,
t is time,
D is the diffusion coefficient,
A is the cross-sectional area, and
x is the distance from the surface.

Assuming steady-state diffusion, we can simplify the equation to:

d^2C/dx^2 = 0

Integrating this equation twice, we get:

C = Ax + B

Using the boundary conditions, we can determine the constants A and B. Given that the concentration at the surface (x = 0) is 1, and the concentration at the interface is 0.5, we have:

C(0) = A(0) + B = 1
C(interface) = A(interface) + B = 0.5

Solving these equations simultaneously, we find A = -2 and B = 1.

Now we can calculate the concentration at the desired points:

C(0) = -2(0) + 1 = 1
C(0.005) = -2(0.005) + 1 = 0.99
C(0.01) = -2(0.01) + 1 = 0.98
C(0.015) = -2(0.015) + 1 = 0.97
C(0.02) = -2(0.02) + 1 = 0.96

To calculate cur in the liquid at the interface, we substitute x = 0 into the concentration equation:

cur = A(0) + B = 1

Therefore, the cur in the liquid at the interface is 1.

Now, we can plot the concentration profile with the calculated values. We can create a graph similar to Fig. 7.1-3b, with concentration on the y-axis and distance from the surface on the x-axis. The plot will show the concentrations at points x = 0, 0.005, 0.01, 0.015, and 0.02 m from the surface, as well as the interface concentration of 0.5.

Learn more about concentration from this link:

https://brainly.com/question/17206790

#SPJ11

Condensation of water vapor

Freezing of water into ice

Option A and E are the correct answer.

We have,

The processes that should lead to a decrease in entropy of the surroundings are:

- Condensation of water vapor:

During condensation, water vapor changes into liquid water, which results in a decrease in the number of possible microstates as the molecules come closer together. This leads to a decrease in entropy.

- Freezing of water into ice:

Freezing involves the transition of liquid water into a more ordered state as ice crystals form.

The arrangement of water molecules in the solid state is more structured than in the liquid state, reducing the number of microstates and resulting in a decrease in entropy.

Therefore,

Condensation of water vapor

Freezing of water into ice

Learn mroe about entropy here:

https://brainly.com/question/34015011

#SPJ4

The height of the transfer unit,

Hoo= H/Nou

= 3.5/0.0507

= 69.08 mHoo

is the height of a theoretical stage in meters.

1. Calculation of mole fraction of SO2 in the liquid outlet stream:

The mole fraction of SO2 in the gas outlet stream is 0.004.

The flow rate of the liquid stream = 2.2 kmol s'

Weight of water = 18 kg/kmol

Density of water = 1000 kg/m³

The volumetric flow rate of the liquid stream= Volume of liquid stream/Time

= (2.2/18) × 1000

= 122.22 m³/s

The mass flow rate of liquid stream= Volume flow rate × density of water

= 122.22 × 1000

= 1.222 × 10⁵ kg/s

Let the mole fraction of SO2 in the liquid outlet stream be x°.

Therefore, the SO2 balance over the column is given by:

Inlet gas = Outlet gas + Absorbed gas

0.0016×0.062 = 0.004 × 0.062 + x°×1.222×10⁵x°=0.000455 which is the mole fraction of SO2 in the liquid outlet stream.

2. Calculation of Number of transfer unit (Nou) for absorption of SO2:

Number of transfer units, Nou=(y° - y*)/(y° - y*a*)= (0.009-0.000455)/(0.009-0)= 0.0507 Units

The Nou value is dimensionless.3. Calculation of Height of transfer unit (Hoo) in meters.

The height of the transfer unit, Hoo= H/Nou= 3.5/0.0507= 69.08 mHoo is the height of a theoretical stage in meters.

Know more about height here:

https://brainly.com/question/73194

#SPJ11