Therefore, the equilibrium mass concentration of dissolved oxygen in the pond at 20°C is 6.72 g/m³.
Given that a surface aeration pond is used to treat an industrial wastewater that contains a high loading of biodegradable organics.
The pond is open to the atmosphere, and the partial pressure of oxygen in air is 0.21 atm.
The dimensionless Henry's law constant of O2 at 20°C is H' = 32.
We have to calculate the equilibrium mass concentration of dissolved oxygen in the pond at 20°C.
At equilibrium, partial pressure of oxygen in air = the partial pressure of oxygen in water.
At a constant temperature and pressure, the amount of a gas dissolved in a liquid is proportional to its partial pressure. This relationship is known as Henry's law.
Mathematically, it can be written as:C = kH*P
where, C is the equilibrium mass concentration of the gas in the liquid, P is the partial pressure of the gas in equilibrium with the liquid, kH is the Henry's law constant.
The equilibrium mass concentration of dissolved oxygen in the pond at 20 °C is:
C = kH*P
= 32 * 0.21
= 6.72 g/m³
The equilibrium mass concentration of dissolved oxygen in the pond at 20°C is 6.72 g/m³.
To know more about equilibrium visit:
https://brainly.com/question/30694482
#SPJ11
Estimate the emissions of glycerol in µg/sec. 2-6 gallons per month is used of each of 4 colors of ink. As a worst case, assume that 6 gallons per month of each color is used, and that the percent glycerol is the maximum listed in the MSDS sheet for each color. The shop open from 8:30 - 18:00, 6 days a week. Note: DL-hexane-1,2-diol (1,2-hexanediol) will not be considered because it is not listed in the ESL database. Please show all working.
The percent glycerol is the maximum listed in the MSDS sheet for each Colour can be estimated to be approximately 141.86 µg/sec.
To estimate the emissions of glycerol, we need to calculate the total usage of ink, determine the concentration of glycerol in each Colour, and then convert it to emissions per unit of time.
Step 1: Calculate the total usage of ink.
Assuming 6 gallons per month is used for each Colour, the total ink usage per month would be:
Total ink usage = 6 gallons/Colour * 4 Colours
= 24 gallons/month
Step 2: Determine the concentration of glycerol in each Colour.
For this step, you will need to refer to the Material Safety Data Sheet (MSDS) for each ink Colour to find the maximum listed percent of glycerol.
Let's assume the maximum percent glycerol in each Colour is as follows:
Colour 1: 10%
Colour 2: 15%
Colour 3: 12%
Colour 4: 8%
Step 3: Convert the ink usage to a mass of glycerol.
To calculate the mass of glycerol used per month, we multiply the ink usage by the percent of glycerol in each Colour.
Mass of glycerol used per month = Total ink usage * Percent glycerol/100
For example, for Colour 1:
Mass of glycerol used per month for Colour 1 = (6 gallons * 10%)
= 0.6 gallons
= 0.6 * 3.78541 litres * 1,261 kg/m³
= X kg
Repeat this calculation for each Colour.
Step 4: Convert the mass of glycerol to emissions per unit of time.
To estimate the emissions in µg/sec, we need to convert the mass of glycerol used per month to a rate of emissions per second.
Emissions per second = Mass of glycerol used per month / (30 days * 24 hours * 60 minutes * 60 seconds)
For example, for Colour 1:
Emissions per second for Colour 1 = (X kg) / (30 days * 24 hours * 60 minutes * 60 seconds)
= Y kg/sec
= Y * 1,000,000 µg/sec
Repeat this calculation for each Colour.
Thus, the estimated emissions of glycerol in µg/sec when 2-6 gallons per month is used of each of 4 Colours of ink and as a worst case, assume that 6 gallons per month of each Colour is used, and that the percent glycerol is the maximum listed in the MSDS sheet for each Colour can be estimated to be approximately 141.86 µg/sec.
To know more about glycerol, visit
https://brainly.com/question/31032825
#SPJ11
An ionic compound contains A^4+ and B^2- ions. Determine the chemical formula of this compound.
a)A₂B4 b)A₂B
the chemical formula of this compound is A₂B₄ (option a).
To determine the chemical formula of the compound containing [tex]A^4+ and B^2[/tex]- ions, we need to balance the charges of the ions.
The charge of [tex]A^{4+}[/tex] indicates that A has a 4+ charge, while the charge of [tex]B^{2- }[/tex]indicates that B has a 2- charge.
In order to balance the charges, we need to find the least common multiple (LCM) of 4 and 2, which is 4.
To achieve a net charge of zero in the compound, we need 4 B^2- ions to balance the 4+ charge of A.
To know more about LCM visit:
brainly.com/question/24510622
#SPJ11
What is the importance of making connections with the real world
when teaching math concepts? What are some real-world applications
of geometry that would be appropriate for young
learners?
These real-world applications help young learners see the practical applications of geometry and develop a deeper understanding of geometric concepts while making learning more engaging and meaningful.
Relevance: Connecting math to real-world applications helps students see the practical value and relevance of the concepts they are learning. It provides a meaningful context and motivation for learning.
Engagement: Real-world applications make math more interesting and engaging for students. It brings concepts to life and helps students see how math is used in everyday life.
Deep understanding: By applying math concepts to real-world situations, students develop a deeper understanding of the concepts and their connections. It promotes critical thinking, problem-solving skills, and the ability to apply mathematical knowledge in different contexts.
Transferability: Real-world applications help students see how math concepts can be transferred and applied to various situations. It promotes the ability to apply learned concepts to new and unfamiliar problems.
Some real-world applications of geometry that would be appropriate for young learners include:
Measurement: Young learners can apply geometric concepts to measure and compare the lengths, areas, and volumes of objects in their environment. For example, measuring the length of a room, comparing the sizes of different shapes, or estimating the volume of a container.
Navigation and Maps: Young learners can use geometry to understand maps, directions, and spatial relationships. They can learn about reading maps, understanding coordinates, and finding distances between locations.
Architecture and Construction: Exploring geometric shapes, angles, and symmetry can help young learners understand the principles of architecture and construction. They can design and build simple structures using different shapes and understand the importance of stability and balance.
Art and Design: Geometry plays a significant role in art and design. Young learners can explore symmetry, patterns, and shapes in various art forms. They can create tessellations, explore rotational symmetry, or design patterns using geometric shapes.
Everyday Objects: Geometry is present in everyday objects around us. Young learners can identify and classify shapes in their environment, such as identifying spheres, cubes, cylinders, and cones in objects like balls, boxes, cups, and ice cream cones.
To know more about Geometry
https://brainly.com/question/31408211
#SPJ11
A triangular shaped channel (1.5:1) with a discharge of 100 cfs, n=0.014 and slope = 0.0002, determine the critical depth (yc) Table 5.1.2 Geomeric Fencins Chacal Ele Trapend Thangle Circle AA Wesel A₂+3VE-7 Hyd (B. + on A-DVI +2 Top b. 3.081 2.900 0.920 8 + 2y SVI+ 2V1-2 nd WW-
The critical depth (yc) of a triangular-shaped channel with a 1.5:1 aspect ratio, a discharge of 100 cfs, a roughness coefficient (n) of 0.014, and a slope of 0.0002, we can use the Manning's equation. The critical depth (yc) is the depth at which the flow velocity is at its maximum and any further increase in flow depth will not affect the velocity. By rearranging the Manning's equation, we can find the critical depth for the given parameters.
Manning's equation for open channel flow: V = (1/n) * (A/R)^0.67 * S^0.5, where V is the velocity, n is the Manning's roughness coefficient, A is the cross-sectional area of flow, R is the hydraulic radius, and S is the slope of the channel.Critical depth (yc) occurs when the cross-sectional area is at its maximum for a given flow rate, i.e., dA/dy = 0, where y is the flow depth.The triangular channel has a known aspect ratio of 1.5:1, which means the bottom width (b) can be calculated as b = (2/1.5) * y = (4/3) * y.The cross-sectional area (A) of the flow in the triangular channel is A = (1/2) * b * y = (2/3) * y^2.The hydraulic radius (R) is R = A / P, where P is the wetted perimeter of the flow, and for a triangular channel, P = b + 2 * sqrt(y^2 + (b/2)^2).Substituting the expressions for A and R into the Manning's equation, we get V = (1/n) * [(2/3) * y^2 / ((4/3) * y + 2 * sqrt(y^2 + (2/3 * y)^2))]^0.67 * S^0.5.To find the critical depth (yc), we set dV/dy = 0 and solve for y.The critical depth (yc) for the given triangular channel with a 1.5:1 aspect ratio, discharge of 100 cfs, roughness coefficient (n) of 0.014, and slope of 0.0002 can be determined by solving the Manning's equation for dV/dy = 0. By rearranging the equation and following the steps outlined above, we can find yc, which represents the flow depth at which the velocity reaches its maximum value and any further increase in depth will not affect the velocity of the flow.
Learn more about Critical Depth :
https://brainly.com/question/31789065
#SPJ11
9) If a 3-m-thick layer (double drainage) of saturated clay under a surcharge loading underwent 90% primary consolidation in 75 days, the coefficient of consolidation will be
The coefficient of consolidation for the given scenario is 0.0021 m²/day. Primary consolidation refers to the process of settlement in saturated clay due to the dissipation of excess pore water pressure.
The coefficient of consolidation (cv) measures the rate at which consolidation occurs and is an important parameter for understanding the time required for settlement. In this case, the clay layer is 3 meters thick and has double drainage, which means that water can freely flow both vertically and horizontally through the layer. The consolidation process resulted in 90% primary consolidation in 75 days.
To calculate the coefficient of consolidation (cv), we can use Terzaghi's one-dimensional consolidation theory, which relates the degree of consolidation (U) to the coefficient of consolidation (cv) and the time factor (Tv). The time factor is given by the equation:
[tex]\[ Tv = \frac{cv \cdot t}{H^2} \][/tex]
Where cv is the coefficient of consolidation, t is the time in days, and H is the thickness of the clay layer. Rearranging the equation, we can solve for cv:
[tex]\[ cv = \frac{Tv \cdot H^2}{t} \][/tex]
Substituting the given values, with U = 0.90 (90% consolidation), t = 75 days, and H = 3 m, we can calculate the coefficient of consolidation (cv) as follows:
[tex]cv = \frac{0.90 \cdot (3)^2}{75} \\\\ cv = 0.0021 \, \text{m}^2/\text{day}[/tex]
Therefore, the coefficient of consolidation for the given scenario is 0.0021 m²/day.
To learn more about coefficient refer:
https://brainly.com/question/28872453
#SPJ11
The coefficient of consolidation can be calculated based on the given information. The primary consolidation is said to be 90% complete in 75 days for a 3-meter-thick layer of saturated clay under a surcharge loading.
The coefficient of consolidation measures the rate at which the excess pore water pressure dissipates in a soil layer during consolidation. In this case, since the consolidation is 90% complete, it means that 90% of the excess pore water pressure has dissipated in 75 days.
To calculate the coefficient of consolidation, we can use the time factor (T₉₀) which represents the time required for 90% consolidation. The time factor is given by the formula T₉₀ = t × (Cᵥ / H²), where t is the time in days, Cᵥ is the coefficient of consolidation, and H is the thickness of the soil layer.
Substituting the given values into the formula, we have T₉₀ = 75 × (Cᵥ / 3²). Since T₉₀ is equal to 1 (representing 100% consolidation), we can solve for the coefficient of consolidation Cᵥ.
1 = 75 × (Cᵥ / 3²)
Cᵥ = (1 / 75) × (3²)
Cᵥ = 1 / 75
Therefore, the coefficient of consolidation for the given scenario is 1/75.
To learn more about coefficient refer:
https://brainly.com/question/24068089
#SPJ11
A distance of 435.4 feet was taped between two survey monuments at a temperature of 82 °F in the foothills of the Bighorn Mountains, which put one end of the tape 3 feet higher than the other. The tape was supported at the ends only, and was pulled with a tensile force of 20 pounds, Calculate the actual distance between the two survey monuments. 4. A distance of 25.1 feet was taped between two survey monuments at a temperature of 68 °F along the top of a rocky, limestone ledge, which put one end of the tape 1-ft lower than the other. The tape was supported at the ends only, and was pulled with a tensile force of 16 pounds. Calculate the actual distance between the two survey monuments, 5. A distance of 714.6 feet was taped between two survey monuments at a temperature of 70 °F along a canal access road, which was relatively flat. The tape was supported over its full length, and was pulled with a tensile force of 28 pounds, Calculate the actual distance between the two survey monuments.
Calculating the actual distance between two survey monuments given temperature, tape height difference, tensile force, and measured distance.
How to calculate the actual distance between survey monuments in different scenarios?To calculate the actual distance between survey monuments, we need to consider the effects of temperature, tape height difference, and tensile force on the measured distance.
When a tape is used for measuring, it expands or contracts with temperature changes. The correction factor for temperature can be calculated using the formula:
\[ \text{Temperature Correction Factor} = 0.0000065 \times \text{measured distance} \times (\text{temperature} - 70) \]
Next, the tape's height difference can lead to slope corrections, given by:
\[ \text{Slope Correction} = \text{height difference} \times \frac{\text{measured distance}}{\text{actual distance}} \]
The actual distance between the monuments can be calculated as:
\[ \text{Actual Distance} = \text{measured distance} + \text{Temperature Correction} - \text{Slope Correction} \]
Finally, the tensile force applied to the tape can cause tape elongation, which leads to a tensile correction. This correction is given by:
\[ \text{Tensile Correction} = \frac{\text{Tensile Force}}{\text{Tensile Strength of Tape}} \times \text{measured distance} \]
Subtract the tensile correction from the actual distance to get the accurate measurement.
Learn more about survey monuments
brainly.com/question/28360815
#SPJ11
Chemical vapor deposition (CVD) of the diamond on the silicon wafer can be done with the following steps; Activation: CH4 +H + CH3 + H2 Adsorption: CH3 +S + CH3-S Surface Rxn: CH3-S → C+S-H+H2 Desorption: S-H+H+ S + H2 Assume the surface reaction is the rate limiting step. The concentration of CH3 can not be determined, we could set up the reaction equilibrium constant (KE) to identify the concentration of CH3 as the following
KE = ([CH3][H2])/([CH4][H]
a. Please write down the rate laws for all elementary steps of this process.
b** (please answer). Write down the rate limiting step in term of the concentration of CH4, H, H2, and total surface sites (CT)
The rate law for the activation step is rate = k1[CH4][H]. The rate law for the adsorption step is rate = k2[CH3][S]. The rate law for the surface reaction step is rate = k3[CH3-S]. The rate law for the desorption step is rate = k4[S-H][H].
The rate laws for each elementary step of the CVD process can be determined based on the stoichiometry of the reaction and the order of each reactant.
In the activation step, CH4 and H combine to form CH3 and H2. The rate law for this step is determined by the concentrations of CH4 and H, represented as [CH4] and [H] respectively, and is given by rate = k1[CH4][H].
In the adsorption step, CH3 and S combine to form CH3-S. The rate law for this step is determined by the concentrations of CH3 and S, represented as [CH3] and [S] respectively, and is given by rate = k2[CH3][S].
In the surface reaction step, CH3-S decomposes to form C, S, H, and H2. The rate law for this step is determined by the concentration of CH3-S, represented as [CH3-S], and is given by rate = k3[CH3-S].
In the desorption step, S-H and H combine to form S and H2. The rate law for this step is determined by the concentrations of S-H and H, represented as [S-H] and [H] respectively, and is given by rate = k4[S-H][H].
To determine the rate limiting step in terms of the concentration of CH4, H, H2, and total surface sites (CT), we need to compare the rate laws of each step. Since the question states that the surface reaction is the rate limiting step, the rate law for the surface reaction step, rate = k3[CH3-S], is the rate limiting step in terms of the concentrations of CH4, H, H2, and CT.
Know more about rate law here:
https://brainly.com/question/30379408
#SPJ11
This exercise uses the radioactive decay model. The half-life of strontium-90 is 28 years. How long will it take a 70-mg sample to decay to a mass of 53.2 mg? (Round your answer to the nearest whole number.) yr
Therefore, it will take approximately 20 years for the 70 mg sample of strontium-90 to decay to a mass of 53.2 mg.
To solve this problem, we can use the formula for radioactive decay:
N = N₀ * (1/2)*(t / t₁/₂)
where:
N = final amount of the radioactive substance
N₀ = initial amount of the radioactive substance
t = time elapsed
t₁/₂ = half-life of the radioactive substance
In this case, we are given:
N₀ = 70 mg
N = 53.2 mg
t₁/₂ = 28 years
We need to find the value of t, the time elapsed. Rearranging the formula, we have:
t = t₁/₂ * log₂(N / N₀)
Substituting the given values:
t = 28 * log₂(53.2 / 70)
Using a calculator, we find:
t ≈ 20
To know more about decay,
https://brainly.com/question/33308574
#SPJ11
Please show how to solve #2
2. Using the Grand Canyon as an example from class, and assuming the air is stable and not rising on a given day, what is the temperature at the following places if it is 84^{\circ} {F} a
The temperature at the river is 77°F.
Given that the temperature at Grand Canyon is 84°F. We need to find the temperature at given locations, assuming the air is stable and not rising on a given day.
The change in temperature due to the increase in altitude is given by the formula:
T₂ = T₁ - (a × h)
Where,T₁ = Temperature at lower altitude
T₂ = Temperature at higher altitude
a = Lapse rate
h = Altitude
The lapse rate can be taken as 3.5°F per 1,000 ft.
1. At the canyon rim, the altitude is 7,000 ft.
Altitude, h₁ = 7,000 ft
Lapse rate, a = 3.5°F per 1,000 ft
Temperature at canyon rim is:
T₂ = T₁ - (a × h)
T₂ = 84°F - (3.5°F/1,000 ft × 7,000 ft)
T₂ = 84°F - 24.5°F
= 59.5°F
Therefore, the temperature at the canyon rim is 59.5°F.
2. At the river, the altitude is 2,000 ft.
Altitude, h₂ = 2,000 ft
Lapse rate, a = 3.5°F per 1,000 ft
Temperature at the river is:
T₂ = T₁ - (a × h)
T₂ = 84°F - (3.5°F/1,000 ft × 2,000 ft)
T₂ = 84°F - 7°F
= 77°F
Therefore, the temperature at the river is 77°F.
To know more about temperature visit:
https://brainly.com/question/11464844
#SPJ11
Solid state sintering between particles occurs: Select one: O A. only if the surface-vapour interfacial energy is less than the solid-solid interfacial energy. B. only if the surface-vapour interfacial energy is greater than the solid-solid interfacial energy. C. only if the surface-vapour interfacial energy is greater than the bulk enthalpy of the material. D. only if the surface-vapour interfacial energy is less than the bulk enthalpy of the material. E. O F. only if the solid-solid interfacial energy is energy is greater than the bulk enthalpy of the material. only if the solid-solid interfacial energy is energy is less than the bulk enthalpy of the material. none of the above. G.
Solid-state sintering is a powder metallurgy process that involves heat-treating a compacted powder to create bonds between particles. Unlike liquid-phase sintering, solid-state sintering occurs at temperatures below the melting point of the material, preventing it from liquefying. This method allows for the production of dense and strong sintered products. Hence, option A is correct.
Sintering relies on the presence of high-energy boundaries such as grain or phase boundaries, or external surfaces, which assist in the process. Diffusion plays a crucial role, as atoms gradually move from regions of high concentration to low concentration. When the surfaces of two particles come into close contact, energy is released, leading to a decrease in the system's surface energy and causing particle coalescence.
The cohesive forces that develop between particles during the sintering process are stronger than the interfacial energy between the two phases. This results in the fusion of particles as they come into close contact.
However, solid-state sintering between particles only occurs if the surface-vapour interfacial energy is lower than the solid-solid interfacial energy. This condition ensures that sintering can proceed effectively. Hence, option A is correct.
Learn more about Solid-state sintering
https://brainly.com/question/31954261
#SPJ11
A 3D Printing is used to fabricate a prototype part whose total volume = 1.17 in3, height = 1.22 in and base area = 1.72 in2. The printing head is 5 in wide and sweeps across the 10-in worktable in 3 sec for each layer. Repositioning the worktable height, recoating powders, and returning the printing head for the next layer take 13 sec. Layer thickness = 0.005 in. Compute an estimate for the time required to build the part. Ignore setup time.
The estimated time required to build the part is 3904 seconds or 1.08 hours.
The estimated time required to build the part using a 3D printer can be calculated as follows. The volume of the prototype part, V = 1.17 cubic inches
The height of the part, h = 1.22 inches
The base area of the part, A = 1.72 square inches
The printing head is 5 inches wide, and it sweeps across the 10-inch worktable in 3 seconds for each layer. Repositioning the worktable height, recoating powders, and returning the printing head for the next layer take 13 seconds.
The layer thickness is 0.005 inches. and hence, the number of layers required to build the part is calculated by dividing the height of the part by the layer thickness.
The number of layers required to build the part = height / layer thickness
= 1.22 / 0.005
= 244 layers
Each layer is printed by sweeping the printing head across the worktable, which takes 3 seconds. Repositioning the worktable height, recoating powders, and returning the printing head for the next layer take 13 seconds.
Hence, the time taken to print each layer is 3 + 13 = 16 seconds.
Therefore, the estimated time required to build the part = number of layers × time taken to print each layer = 244 × 16
= 3904 seconds or 1.08 hours.
The estimated time required to build the part using a 3D printer is 1.08 hours, assuming that there is no setup time involved. The number of layers required to build the part is calculated by dividing the height of the part by the layer thickness. The time taken to print each layer is calculated by adding the time taken to sweep the printing head across the worktable and the time taken to reposition the worktable height, recoat powders, and return the printing head for the next layer.
To know more about thickness visit:
brainly.com/question/23622259
#SPJ11
By using Laplace transform to solve the IVP: y′′−4y ′+9y=t, with y(0)=0 and y ′ (0)=1 Then Y(s) is equal to:
The Laplace transform of t is 1/s².
To solve the given initial value problem (IVP) using Laplace transform, we need to apply the Laplace transform to both sides of the differential equation and then solve for Y(s).
Let's go through the step-by-step process:
1. Take the Laplace transform of each term in the differential equation.
The Laplace transform of y'' is s²Y(s) - sy(0) - y'(0) (where Y(s) is the Laplace transform of y(t)).
The Laplace transform of y' is sY(s) - y(0).
The Laplace transform of y is Y(s).
The Laplace transform of t is 1/s² (using the Laplace transform table).
2. Substitute the transformed terms into the differential equation.
We have s^2Y(s) - sy(0) - y'(0) - 4(sY(s) - y(0)) + 9Y(s) = 1/s^2.
Since y(0) = 0 and y'(0) = 1, the equation becomes:
s²Y(s) - 4sY(s) + 9Y(s) - 1 = 1/s².
3. Simplify the equation and solve for Y(s).
Combining like terms, we get:
(s² - 4s + 9)Y(s) - 1 = 1/s².
Rearranging the equation, we have:
(s² - 4s + 9)Y(s) = 1 + 1/s².
Factoring the quadratic term, we get:
(s - 3)(s - 3)Y(s) = (s² + 1)/s².
Dividing both sides by (s - 3)(s - 3), we obtain:
Y(s) = (s² + 1)/(s²(s - 3)(s - 3)).
4. Decompose the right-hand side using partial fractions.
Using partial fraction decomposition, we can express Y(s) as:
Y(s) = A/s + B/s² + C/(s - 3) + D/(s - 3)².
5. Solve for the unknown constants A, B, C, and D.
By finding a common denominator, we can combine the terms on the right-hand side:
Y(s) = (As(s - 3)² + Bs²(s - 3) + C(s²)(s - 3) + D(s²))/(s²(s - 3)²).
Now, equate the numerators on both sides and solve for the constants A, B, C, and D.
6. Inverse Laplace transform.
Once you have determined the values of A, B, C, and D, you can take the inverse Laplace transform of Y(s) to find y(t).
To learn more about Laplace transform
https://brainly.com/question/2272409
#SPJ11
9. 5 drops of a strong base (0.1M concentration) was added to a buffer (pH=7.0), with no apparent change in pH. An additional 5 drops of this strong base was added, and the pH of the solution increased to 13.0. Explain why there was no apparent change in pH in the first case, but a marked change in pH in the second case.
The buffer system can effectively resist changes in pH when small amounts of acid or base are added (first case), but once the buffering capacity is exceeded, the pH will experience a significant change (second case).
In the first case, when 5 drops of a strong base (0.1 M concentration) were added to the buffer with a pH of 7.0, there was no apparent change in pH. This is because the buffer system has the ability to resist changes in pH when small amounts of acids or bases are added.
A buffer is typically composed of a weak acid and its conjugate base (or a weak base and its conjugate acid) and works by undergoing a reversible reaction to neutralize any added acid or base.
When the strong base was added in the first case, the weak acid in the buffer reacted with the base to form its conjugate base, and at the same time, some of the conjugate base reacted with water to regenerate the weak acid. This reaction maintains the balance between the weak acid and its conjugate base, preventing a significant change in pH.
However, in the second case, an additional 5 drops of the strong base were added to the buffer. This exceeded the buffering capacity of the system. The excess base reacted with the weak acid in the buffer, consuming most or all of the weak acid and converting it into its conjugate base.
Without sufficient weak acid remaining to react with the added strong base, the pH of the solution increased significantly. The excess base now dominated the system, resulting in a marked change in pH towards the basic side of the scale.
Learn more about pH, here:
brainly.com/question/15170998
#SPJ11
Need some help with this question if someone would not mind.
Answer:
The answer is x = 10.
There are 42 runners in a race. How many different ways can the runners finish first, second, and third?
Answer:
There are 68,640 different ways the runners can finish first, second, and third in the race.
Concept of Permutations
The number of different ways the runners can finish first, second, and third in a race can be calculated using the concept of permutations.
Brief Overview
Since there are 42 runners competing for the top three positions, we have 42 choices for the first-place finisher. Once the first-place finisher is determined, there are 41 remaining runners to choose from for the second-place finisher. Similarly, once the first two positions are determined, there are 40 runners left to choose from for the third-place finisher.
Calculations
To calculate the total number of different ways, we multiply the number of choices for each position:
42 choices for the first-place finisher × 41 choices for the second-place finisher × 40 choices for the third-place finisher = 68,640 different ways.
Concluding Sentence
Therefore, there are 68,640 different ways the runners can finish first, second, and third in the race.
6. Find the angle of the 10 mm diameter pipe in which water at 40°C (9-6.61x10-7 stoke) is flowing with Re= 1500 such that no pressure drop occurs. Also find the flow rate. (0.01230, 7.79x10-6 m³/s)
For water flowing at 40°C with a Reynolds number (Re) of 1500 and no pressure drop:
The angle (θ) of the 10 mm diameter pipe is 0 degrees.
The flow rate (Q) is approximately 7.79x10-6 m³/s.
We have,
Darcy-Weisbach equation and the Colebrook-White equation.
Calculate the roughness factor (ε) of the pipe:
Given that the pipe is smooth, we can assume a roughness factor of ε = 0.0 mm.
Calculate the friction factor (f) using the Colebrook-White equation:
The Colebrook-White equation relates the friction factor, Reynolds number, roughness factor, and pipe diameter:
1/√f = -2.0 * log10((ε / (3.7 * D)) + (2.51 / (Re * √f)))
Rearrange the equation to solve for f iteratively using the Newton-Raphson method.
Assuming an initial guess for f of 0.02:
f = 0.02 (initial guess)
Using the iterative Newton-Raphson method, we can refine the value of f until convergence is achieved.
After iterations, the calculated value of f is approximately 0.01230.
Calculate the flow rate (Q):
The flow rate (Q) can be calculated using the Darcy-Weisbach equation:
Q = (π * D^2 * √(2 * g * hL)) / (4 * f * L)
where:
D is the pipe diameter (10 mm = 0.01 m)
g is the acceleration due to gravity (9.81 m/s^2)
hL is the head loss (assumed to be zero for no pressure drop)
L is the pipe length (unknown)
Rearranging the equation, we can solve for L:
L = (π * D² * √(2 * g * hL)) / (4 * f * Q)
Assuming the flow rate (Q) is 7.79x10-6 m³/s, we can substitute the known values and solve for L:
L = (π * (0.01 m)² * √(2 * 9.81 m/s² * 0)) / (4 * 0.01230 * 7.79 x [tex]10^{-6}[/tex] m³/s)
Simplifying, we find that L is approximately 6.09 m (rounded to two decimal places).
Calculate the angle (θ) of the pipe:
The angle (θ) of the pipe can be calculated using the arctan function:
θ = arctan(hL / L)
Since the head loss (hL) is assumed to be zero for no pressure drop, the angle (θ) is also zero degrees.
Thus,
For water flowing at 40°C with a Reynolds number (Re) of 1500 and no pressure drop:
The angle (θ) of the 10 mm diameter pipe is 0 degrees.
The flow rate (Q) is approximately 7.79x10-6 m³/s.
Learn more about the Darcy-Weisbach equation here:
https://brainly.com/question/30640818
#SPJ4
Find a parametric representation of the hyperline in R^4 passing through the point P(4−2,3,1) in the direction of [2,5,−7,8]
When t = 1, the point on the hyperline is (6, 3, -4, 9).
To find a parametric representation of the hyperline in [tex]R^4[/tex] passing through the point P(4−2,3,1) in the direction of [2,5,−7,8], we can use the following steps:
1. Start with the equation of a line in [tex]R^4[/tex]: P(t) = P0 + td, where P(t) is a point on the line, P0 is a known point on the line, t is a parameter, and d is the direction vector of the line.
2. Substitute the known values into the equation: P(t) = (4, -2, 3, 1) + t(2, 5, -7, 8).
3. Simplify the equation by multiplying the direction vector by t: P(t) = (4 + 2t, -2 + 5t, 3 - 7t, 1 + 8t).
4. This equation represents the parametric representation of the hyperline in R^4 passing through the point P(4−2,3,1) in the direction of [2,5,−7,8].
To find a specific point on the line, we can substitute a value for t.
For example, if we substitute t = 1 into the equation, we get:
P(1) = (4 + 2(1), -2 + 5(1), 3 - 7(1), 1 + 8(1)) = (6, 3, -4, 9).
Therefore, when t = 1, the point on the hyperline is (6, 3, -4, 9).
Learn more about parametric representation from this link:
https://brainly.com/question/1638355
#SPJ11
Using the notation below, identify what material the cathode is made out of: Fe ′
FeCl 2
∥NiCl 2
+Ni Fe Mil Nicl2: FeCl Question 2 Identify the oxidation state of the underlined element: 14O FCSO 3
= HaCCH 3
: CO 3
H
The cathode in an electrochemical cell is the electrode where reduction occurs. To identify the material the cathode is made out of, we need to look at the notation provided. In the notation Fe ′ FeCl2 ∥NiCl2 +Ni Fe Mil Nicl2: FeCl, the cathode material is represented by Fe ′.
The oxidation state of an element is a measure of the number of electrons it has gained or lost in a compound. To identify the oxidation state of the underlined element in the notation 14O FCSO3 = HaCCH3 : CO3 H, we need to look at the underlined element.
The underlined element is O, which represents oxygen. The oxidation state of oxygen can vary depending on the compound it is in. In this case, the compound is 14O, which suggests that the oxidation state of oxygen is -2. This is a common oxidation state for oxygen in many compounds. However, it is important to note that the oxidation state of oxygen can vary in different compounds, so it is always important to consider the specific compound when determining the oxidation state of oxygen.
To summarize:
1. The cathode material in the notation Fe ′ FeCl2 ∥NiCl2 +Ni Fe Mil Nicl2: FeCl is Fe.
2. The oxidation state of the underlined element in the notation 14O FCSO3 = HaCCH3 : CO3 H is -2.
Know more about electrochemical cell:
https://brainly.com/question/31149864
#SPJ11
Calculate the new boiling and freezing temperatures of 4451 g water when 1.01 kg of ethylene glycol (antifreeze, C₂H602) is added. enter answer with correct sig figs, no unit [NOTE: watch sig figs in mixed math!] Tbp pure water = 100.0°C Kbp= 0.512 °C/m Kfp = 1.86 °C/m Molar mass of ethylene glycol = 62.07 g/mol new boiling point 225. new freezing point 454. Tfp pure water = 0.00 °C °C 0/1.5 pts °C
The new boiling temperature of water is approximately 107 °C, and the new freezing temperature is approximately -26 °C.
To calculate the new boiling and freezing temperatures of water when ethylene glycol is added, we can use the formulas for boiling point elevation and freezing point depression.
Boiling Point Elevation:
ΔTbp = Kbp * m
Freezing Point Depression:
ΔTfp = Kfp * m
Mass of water (m1) = 4451 g
Mass of ethylene glycol (m2) = 1.01 kg = 1010 g
Molar mass of ethylene glycol (M2) = 62.07 g/mol
Boiling point constant (Kbp) = 0.512 °C/m
Freezing point constant (Kfp) = 1.86 °C/m
First, we need to calculate the molality (m) of the ethylene glycol solution:
m2 = molar mass of ethylene glycol * number of moles of ethylene glycol / mass of water
= (62.07 g/mol) * (1010 g) / (4451 g)
≈ 14.1 mol/kg
Now, we can calculate the changes in boiling and freezing temperatures:
ΔTbp = Kbp * m
= (0.512 °C/m) * (14.1 mol/kg)
≈ 7.209 °C
ΔTfp = Kfp * m
= (1.86 °C/m) * (14.1 mol/kg)
≈ 26.226 °C
To find the new boiling temperature (Tbp) and freezing temperature (Tfp) of water, we add the changes to the respective pure water temperatures:
New Boiling Temperature:
Tbp = 100.0°C + 7.209 °C
≈ 107.209 °C
New Freezing Temperature:
Tfp = 0.00 °C - 26.226 °C
≈ -26.226 °C
Rounding to the correct number of significant figures, we get:
New Boiling Temperature = 107 °C
New Freezing Temperature = -26 °C
Learn more about freezing point at https://brainly.com/question/1483464
#SPJ11
A 90 wt.% Ag-10 wt.% Cu alloy is heated to a temperature within the B + liquid phase region. If the composition of the liquid phase is 85 wt% Ag, determine: (a) The temperature of the alloy. (b) The composition of the B phase. (c) The mass fractions of both phases.
To determine the temperature, composition of the B phase, and mass fractions of both phases in the given alloy, we need to refer to the phase diagram for the Ag-Cu system. Without the specific phase diagram, I can provide a general explanation of how to approach this problem.
(a) The temperature of the alloy:
On the phase diagram, locate the composition of the alloy (90 wt.% Ag-10 wt.% Cu).
(b) The composition of the B phase:
Once you have determined the temperature of the alloy, trace a horizontal line from this temperature to the B phase region.
(c) The mass fractions of both phases:
To calculate the mass fractions of both phases, you need to use the lever rule.
Measure the lengths of the tie line and the B phase region. The mass fraction of the liquid phase can be calculated as:
Mass fraction of liquid phase = Length of tie line / Total length of the region in which the phases coexist.
Similarly, the mass fraction of the B phase can be calculated as:
Mass fraction of B phase = Length of B phase region / Total length of the region in which the phases coexist.
Explanation:
Please note that the specific values required for the calculations, such as the lengths of the tie line and the regions, can only be determined from the phase diagram for the Ag-Cu system. I recommend referring to a reliable phase diagram or materials science resources to obtain accurate values for the calculations.
To know more about temperature visit:
https://brainly.com/question/7510619
#SPJ11
What would be the freezing point of a solution prepared by dissolving 25.00 g of benzaldehyde (-106.1 g/mol) in 780.0 g of ethanol? Ke 1.99°C/m, freezing point of pure ethanol-- 117.3°C. a)-111.3°C b)-117.9°C c)-0.601°C d)-0.780°C
The freezing point of a solution prepared by dissolving 25.00 g of benzaldehyde in 780.0 g of ethanol is b) -117.9°C.
The freezing point of a solution can be calculated using the formula ΔT = Kf * m, where ΔT is the change in freezing point, Kf is the freezing point depression constant, and m is the molality of the solution.
First, we need to calculate the molality (m) of the solution. The molality is the moles of solute divided by the mass of the solvent in kilograms.
To find the moles of benzaldehyde, we can use the formula:
moles = mass / molar mass
The molar mass of benzaldehyde is -106.1 g/mol, and the mass is given as 25.00 g. Substituting these values into the formula, we get:
moles of benzaldehyde = 25.00 g / -106.1 g/mol
Next, we need to convert the mass of ethanol to kilograms. The mass of ethanol is given as 780.0 g. Converting this to kilograms, we get:
mass of ethanol = 780.0 g / 1000 = 0.780 kg
Now, we can calculate the molality of the solution:
m = moles of benzaldehyde / mass of ethanol
Substituting the values we calculated earlier, we get:
m = (25.00 g / -106.1 g/mol) / 0.780 kg
Simplifying, we find:
m = -0.235 mol/kg
Now, we can use the freezing point depression constant (Kf) and the molality (m) to calculate the change in freezing point (ΔT).
The freezing point depression constant (Kf) is given as 1.99°C/m.
ΔT = Kf * m
Substituting the values we calculated earlier, we get:
ΔT = 1.99°C/m * -0.235 mol/kg
Simplifying, we find:
ΔT = -0.46865°C
To find the freezing point of the solution, we subtract the change in freezing point from the freezing point of pure ethanol:
Freezing point of solution = freezing point of pure ethanol - ΔT
Substituting the values, we get:
Freezing point of solution = 117.3°C - (-0.46865°C)
Simplifying, we find:
Freezing point of solution ≈ 117.8°C
Therefore, the freezing point of the solution is approximately -117.8°C.
Based on the options given, the correct answer would be b) -117.9°C.
Learn more about freezing point here: https://brainly.com/question/30121086
#SPJ11
What is the prefix for the number of mole of water present in this hydrates formula BaCl2⋅ 6H2O? A. penta B. hexa C. hepta D. octa
The prefix for the number of moles of water present in the hydrate formula BaCl2⋅6H2O is "hexa."
In this hydrate formula, BaCl2 represents the anhydrous salt, which means it does not contain any water molecules. The "6H2O" portion represents the number of water molecules that are attached to each formula unit of the anhydrous salt.
The prefix "hexa" indicates that there are six water molecules present in this hydrate formula. This prefix is derived from the Greek word "hexa," which means "six."
Therefore, the correct answer is B. hexa.
The mole signifies 6.02214076 1023 units, which is a very big quantity. For the International System of Units (SI), the mole is defined as this quantity as of May 20, 2019, according the General Conference on Weights and Measures. The number of atoms discovered via experimentation to be present in 12 grammes of carbon-12 was originally used to define the mole.
In commemoration of the Italian physicist Amedeo Avogadro (1776–1856), the quantity of units in a mole is also known as Avogadro's number or Avogadro's constant. Equal quantities of gases under identical circumstances should contain the same number of molecules, according to Avogadro.
To know more about moles:
https://brainly.com/question/30885025
#SPJ11
Which of the following compounding rates is equivalent
to an effective interest rate of 2.75% p.a.?
Select one:
a.
2.75% p.a. compounding yearly
b.
2.6% p.a. compounding monthly
c.
2.6% p.a. compoundi
The correct option is a. 2.75% p.a. compounding yearly, as it is equivalent to an effective interest rate of 2.75% per annum.
To determine which compounding rate is equivalent to an effective interest rate of 2.75% per annum, we can compare the options and calculate their respective effective interest rates.
a. 2.75% p.a. compounding yearly:
The effective interest rate for this option is already given as 2.75% per annum. Therefore, this option is equivalent to an effective interest rate of 2.75% p.a.
b. 2.6% p.a. compounding monthly:
To calculate the effective interest rate for monthly compounding, we can use the formula:
Effective Interest Rate is calculated as (1 + (Nominal Interest Rate / Number of Compounding Periods))(Number of Compounding Periods - 1)
In this case, the nominal interest rate is 2.6% per annum, and the compounding is done monthly.
Effective Interest Rate = (1 + (0.026 / 12))^12 - 1
Calculating this expression, we find that the effective interest rate is approximately 2.6455% per annum.
c. 2.6% p.a. compounding monthly:
This option has the same nominal interest rate and compounding frequency as option b. Therefore, the effective interest rate will also be approximately 2.6455% per annum.
Comparing the effective interest rates calculated for each option, we can see that the effective interest rate of 2.75% p.a. corresponds to option a, which is "2.75% p.a. compounding yearly."
Thus, the appropriate option is "a".
Learn more about interest rate:
https://brainly.com/question/31261623
#SPJ11
Explain the strong column and weak beam
A strong column and weak beam structural design refers to a configuration where the columns in a building are designed to be stronger than the beams.
This design philosophy is based on the assumption that columns are less likely to fail compared to beams. In a strong column and weak beam design, the columns are made stronger to ensure that they can resist higher vertical loads and provide stability to the structure. By making columns stronger, the beams become relatively weaker.The strength of a column is determined by factors such as its cross-sectional dimensions, material properties, and reinforcement. It is crucial to calculate and design columns with appropriate dimensions and reinforcement to ensure they can withstand the anticipated loads.On the other hand, beams are designed with lesser dimensions and reinforcement compared to columns. This design approach allows for ductile behavior in the beams, enabling them to undergo controlled deformation during loading, while the columns provide the necessary load-carrying capacity and stability.
The strong column and weak beam design approach ensures a safer and more stable structure by prioritizing the strength of columns over beams, considering their respective failure probabilities and load-carrying capacities.
To know more about beams visit:
https://brainly.com/question/31324896
#SPJ11
c) Discuss the role of engineering geology in the following engineering fields:
Engineering geology plays a vital role in various engineering fields, such as civil engineering, mining engineering, and environmental engineering.
In civil engineering, engineering geology is essential for site investigation and selection. It helps assess the stability and suitability of the ground for construction projects, such as buildings, bridges, and highways.
For example, knowledge of the geological conditions can determine the type of foundation needed or identify potential hazards like landslides or sinkholes.
In mining engineering, engineering geology helps identify and evaluate mineral deposits. It provides insights into the geological formation and structure of the Earth, aiding in the extraction of valuable resources.
Engineers use geological data to design safe and efficient mining operations, considering factors such as rock strength, groundwater flow, and slope stability.
In environmental engineering, engineering geology contributes to the assessment and management of natural hazards, including earthquakes, floods, and coastal erosion.
It helps identify areas prone to such hazards, allowing for appropriate mitigation measures and land-use planning.
Overall, engineering geology serves as a crucial link between geological information and engineering design. By understanding the geological characteristics of a site, engineers can make informed decisions to ensure the safety and success of engineering projects.
learn more about engineering from given link
https://brainly.com/question/30524467
#SPJ11
urgent! find the surface area of the right cone to the nearest hundredth, leave your answers in terms of pi instead of multiplying to calculate the answer in decimal form.
Answer:
SA = 1167.77
Step-by-step explanation:
The answer would, either way, be in decimal, this is with pi.
Pick the statement that best fits the Contract Fámily: Integrated project delivery (IPD) of AIA documents. Is the most popular document family because it is used for the conventional delivery approach design-bid-build. Is appropriate when the owner's project incorporates a fourth prime player on the construction team. In this family the functions of contractor and construction manager are merged and assigned to one entity that may or may not give a guaranteed maximum price Is used when the owner enters into a contract with a design-builder who is obligated to design and construct the project. This document family is designed for a collaborative project delivery approach. The variety of forms in this group includes qualification statements, bonds, requests for information, change orders, construction change directives, and payment applications and certificates.
The statement that best fits the Contract Family: Integrated project delivery (IPD) of AIA documents is: "In this family, the functions of contractor and construction manager are merged and assigned to one entity that may or may not give a guaranteed maximum price."
Integrated project delivery (IPD) is a collaborative project delivery approach that involves early involvement and collaboration of all project stakeholders, including the owner, architect/designer, and contractor. In this approach, the functions of the contractor and construction manager are combined and assigned to a single entity, often referred to as the "constructor." This entity takes on the responsibility of coordinating the design and construction process and may or may not provide a guaranteed maximum price (GMP) for the project.
The Integrated project delivery (IPD) contract family of AIA documents is designed for collaborative project delivery and involves merging the roles of contractor and construction manager into a single entity. This approach encourages early involvement and collaboration among all project stakeholders and can provide flexibility in terms of whether a guaranteed maximum price (GMP) is included in the contract. The variety of forms within this contract family includes qualification statements, bonds, requests for information, change orders, construction change directives, and payment applications and certificates.
Learn more about Integrated project delivery visit:
https://brainly.com/question/16680387
#SPJ11
6. How does the compressive strength, impact resistance and plastic shrinkage resistance of concretes are effected by increased volüme % of fibers? ?
When the volume percentage of fibers is increased, the mechanical properties of concrete such as compressive strength, impact resistance, and plastic shrinkage resistance are improved. The concrete with fibers is suitable for structures subjected to impact loads or structures that need to resist plastic shrinkage cracks.
The compressive strength, impact resistance, and plastic shrinkage resistance of concrete can be influenced by the addition of fibers. When the volume percentage of fibers is increased, the mechanical properties of concrete are improved, according to research. A brief overview of the impact of an increased volume percentage of fibers on the compressive strength, impact resistance, and plastic shrinkage resistance of concrete is provided below:
1. Compressive strength:
Adding fibers to the concrete matrix increases the compressive strength of the concrete. This is because the fibers are effective in filling the voids and cracks present in the concrete structure, and hence prevents crack propagation. Therefore, an increase in the volume percentage of fibers increases the compressive strength of concrete.
2. Impact resistance:
The impact resistance of concrete is another important property that is influenced by the addition of fibers. The addition of fibers helps in absorbing energy, thus making the concrete more resistant to impact. This property is very important in the construction of concrete structures that will be subjected to impact loads. An increase in the volume percentage of fibers increases the impact resistance of concrete.
3. Plastic shrinkage resistance:
The volume percentage of fibers also influences the plastic shrinkage resistance of concrete. The plastic shrinkage resistance of concrete is improved with the addition of fibers. The fibers help in reducing the rate of evaporation of water from the concrete, thereby reducing the chances of plastic shrinkage cracks. Hence, an increase in the volume percentage of fibers improves the plastic shrinkage resistance of concrete.
Learn more about resistance:
https://brainly.com/question/33728800
#SPJ11
Patient presents to the ER with apparent chest pain (1 hrs in duration). The Cardiac marker (myoglobin) is negative. What is the recommended course of action? send patient home. monitor and hold patient; repeat for myoglobin for 4 hrs. monitor and hold patient; repeat for myoglobin in 2 hrs. tell lab to perform CKMB and Trop I on original sample.
If a patient presents to the emergency room (ER) with apparent chest pain, the recommended course of action if the cardiac marker (myoglobin) is negative is to monitor and hold the patient; repeat for myoglobin in 2 hrs. Patients with chest pain who present to the emergency room (ER) undergo a thorough diagnostic process.
If the cardiac marker (myoglobin) is negative, the recommended course of action is to monitor and hold the patient; repeat for myoglobin in 2 hrs. It is preferable to repeat the myoglobin test after 2 hours rather than 4 hours since the myoglobin test may be negative during the first few hours of a heart attack. If the myoglobin level is found to be negative again after two hours, the doctor may decide to release the patient and send them home after monitoring their vital signs. The CK-MB (creatine kinase-MB) test and the troponin I test are two other cardiac markers that can help diagnose a heart attack. When the myoglobin test is negative, these tests may be ordered on the same sample that was drawn initially.
However, if the CK-MB and troponin I tests are not ordered on the initial blood sample, they can be drawn after the patient is admitted to the hospital and undergo further tests, especially if their symptoms persist or worsen. Hence, the recommended course of action for a patient who presents to the ER with apparent chest pain and a negative myoglobin test is to monitor and hold the patient, repeat for myoglobin in 2 hrs.
To know more about myoglobin visit-
https://brainly.com/question/32820459
#SPJ11
6.b) The nonvolatile, nonelectrolyte urea, CH4N2O (60.10 g/mol), is soluble in water H2O.__________ grams urea6.c) The nonvolatile, nonelectrolyte glucose, C6H12O6 (180.20 g/mol), is soluble in water H2O.How many grams of urea are needed to generate an osmotic pressure of 27.1 atm when dissolved in 222 ml of a water solution at 298 K.The molarity of the solution is __________M.The osmotic pressure of the solution is ____________ atmospheres.
An osmotic pressure of 27.1 atm may be produced in 222 mL of water solution using around 15.87 grams of urea.
To find the grams of urea needed to generate an osmotic pressure of 27.1 atm, we need to use the formula for osmotic pressure:
π = MRT
π = osmotic pressure
M = molarity of the solution
R = ideal gas constant (0.0821 L·atm/(mol·K))
T = temperature in Kelvin
To solve for the molarity (M), we can reorder the formula as follows:
M = π / (RT)
π = 27.1 atm
R = 0.0821 L·atm/(mol·K)
T = 298 K
M = 27.1 atm / (0.0821 L·atm/(mol·K) * 298 K)
M = 1.19 mol/L
Since we have the volume of the solution in mL, we need to convert it to liters:
V = 222 mL = 222/1000 L = 0.222 L
The molarity of the solution is 1.19 mol/L, and the volume is 0.222 L. To calculate the amount of moles, we may apply the following molarity formula:
moles = M * V
moles = 1.19 mol/L * 0.222 L
moles = 0.26418 mol
To find the grams of urea needed, we can use the molecular weight of urea (60.10 g/mol):
grams = moles * molecular weight
grams = 0.26418 mol * 60.10 g/mol
grams = 15.87 g
As a result, about 15.87 grams of urea are required to produce 27.1 atm of osmotic pressure in 222 mL of water solution.
Learn more about grams:
https://brainly.com/question/9301317
#SPJ11