The resistance of the resistor in the circuit is approximately 21.95 ohms.
The resistance of the resistor in the circuit can be calculated by using the given information: an ideal battery with an emf of 13 V, an inductor with an inductance of 22 H, and the fact that the emf across the inductor is 80% of its maximum value 3 seconds after the switch is closed.
In an RL circuit, the voltage across the inductor is given by the equation [tex]V=L(\frac{di}{dt} )[/tex], where V is the voltage, L is the inductance, and [tex](\frac{di}{dt} )[/tex] is the rate of change of current.
Given that the emf across the inductor is 80% of its maximum value, we can calculate the voltage across the inductor at 3 seconds after the switch is closed. Let's denote this voltage as Vₗ.
Vₗ = 0.8 × (emf of the battery)
Vₗ = 0.8 × 13 V
Vₗ = 10.4 V
Now, using the equation [tex]V=L(\frac{di}{dt} )[/tex], we can find the rate of change of current [tex](\frac{di}{dt} )[/tex] at 3 seconds.
10.4 V = 22 H × (di/dt)
[tex](\frac{di}{dt} )[/tex] = 10.4 V / 22 H
[tex](\frac{di}{dt} )[/tex] = 0.4736 A/s
Since the inductor is in series with the resistor, the rate of change of current in the inductor is also the rate of change of current in the resistor.
Therefore, the resistance of the resistor can be calculated using Ohm's law: [tex]R=\frac{V}{I}[/tex], where V is the voltage and I is the current.
R = 10.4 V / 0.4736 A/s
R ≈ 21.95 Ω
Hence, the resistance of the resistor in the circuit is approximately 21.95 ohms.
Learn more about resistor here:
https://brainly.com/question/30672175
#SPJ11
Two life preservers have identical volumes, but one is filled with styrofoam while the other is filled with small lead pellets. If you fell overboard into deep water, which would provide you the greatest buoyant force? same on each as long as their volumes are the same styrofoam filled life preserver O not enough information given lead filled life preserver
Two life preservers have identical volumes, but one is filled with styrofoam while the other is filled with small lead pellets. the buoyant force provided by both the styrofoam-filled and lead-filled life preservers would be the same,
The buoyant force experienced by an object immersed in a fluid depends on the volume of the object and the density of the fluid. In this case, the two life preservers have identical volumes, which means they displace the same volume of water when submerged.nThe buoyant force experienced by an object is equal to the weight of the fluid displaced by the object. The weight of the fluid is directly proportional to its density. Since the life preservers have the same volume, the buoyant force they experience will be the same as long as the density of the fluid (water, in this case) remains constant.
Therefore, the buoyant force provided by both the styrofoam-filled and lead-filled life preservers would be the same, assuming their volumes are identical. The choice of material (styrofoam or lead pellets) inside the life preserver does not affect the buoyant force as long as the volumes of the preservers are the same. The buoyant force solely depends on the volume of the object and the density of the fluid.
Learn more about buoyant force here:
https://brainly.com/question/21990136
#SPJ11
27. The electric potential \( 1.6 \mathrm{~m} \) from a point charge \( q \) is \( 3.8 \times 10^{4} \mathrm{~V} \). What is the value of \( a \) ?
The value of a is 4.2 cm.
Given information:The electric potential \( 1.6 \mathrm{~m} \) from a point charge \( q \) is \( 3.8 \times 10^{4} \mathrm{~V} \).We need to find the value of a.The potential due to a point charge at a distance r is given by,V= kq/r,where k is the electrostatic constant or Coulomb’s constant which is equal to 1/(4πε0) and its value is k = 9 × 109 Nm2/C2ε0 is the permittivity of free space and its value is ε0 = 8.854 × 10−12 C2/Nm2.
Now substituting the given values we have,3.8 × 104 = (9 × 109 × q)/1.6The value of q is3.8 × 104 × 1.6/9 × 109= 6.747 × 10−7 C.Now we need to find the value of a.We know that the potential at a distance r from a point charge q is given by,V = kq/r (k = 9 × 109 Nm2/C2).Here, V = 3.8 × 104 V and r = 1.6 mSubstituting the given values we have,3.8 × 104 = (9 × 109 × 6.747 × 10−7)/aa = 0.042 m or a = 4.2 cmAnswer:Therefore, the value of a is 4.2 cm.
Learn more about electrostatic here,
https://brainly.com/question/17692887
#SPJ11
A helicopter lifts a 82 kg astronaut 19 m vertically from the ocean by means of a cable. The acceleration of the astronaut is g/10. How much work is done on the astronaut by (a) the force from the helicopter and (b) the gravitational force on her? Just before she reaches the helicopter, what are her (c) kinetic energy and (d) speed? (a) Number ______________ Units _____________
(b) Number ______________ Units _____________
(c) Number ______________ Units _____________
(d) Number ______________ Units _____________
Answer: (a) The work done on the astronaut by the force from the helicopter is 1528.998 J. The units of work are Joules.
(b) The work done on the astronaut by the gravitational force on her is 15284.98 J. The units of work are Joules.
(c) The kinetic energy of the astronaut just before she reaches the helicopter is 15224.22 J. The units of work are Joules.
(d) Therefore, her speed just before she reaches the helicopter is 7.26 m/s. The units of speed are m/s.
Mass of the astronaut, m = 82 kg
Height to which the astronaut is lifted, h = 19 m
Acceleration of the astronaut, a = g/10 = 9.81/10 m/s² = 0.981 m/s²
(a) Work done
W = Fd
Here, d = h = 19 m,
The force applied, F = ma
F = 82 x 0.981
= 80.442 N.
Work done on the astronaut by the force from the helicopter, W₁ = FdW₁ = 80.442 x 19 = 1528.998 J.
The work done on the astronaut by the force from the helicopter is 1528.998 J. The units of work are Joules.
(b) The work done on the astronaut by the gravitational force on her is given by the product of the force of gravity and the displacement of the astronaut.
W = mgd
Here, d = h = 19 m
The gravitational force acting on the astronaut, mg = 82 x 9.81 = 804.42 N.
Work done on the astronaut by the gravitational force on her, W₂ = mgdW₂ = 804.42 x 19 = 15284.98 J.
The work done on the astronaut by the gravitational force on her is 15284.98 J. The units of work are Joules.
(c) Before the astronaut reaches the helicopter, her potential energy is converted into kinetic energy.
Therefore, the kinetic energy of the astronaut just before she reaches the helicopter is equal to the potential energy she has at the height of 19 m.
Kinetic energy of the astronaut, KE = Potential energy at 19 m.
KE = mgh
KE = 82 x 9.81 x 19
KE = 15224.22 J.
The kinetic energy of the astronaut just before she reaches the helicopter is 15224.22 J. The units of work are Joules.
(d) The kinetic energy of the astronaut just before she reaches the helicopter is equal to the work done on her by the force from the helicopter just before she reaches the helicopter. So,
KE = W₁
Therefore, her speed just before she reaches the helicopter can be found by equating the kinetic energy to the work done on her by the force from the helicopter and solving for velocity.
KE = 1/2 mv²
v = √(2KE/m)
v = √(2 x 1528.998/82)
v = 7.26 m/s.
Therefore, her speed just before she reaches the helicopter is 7.26 m/s. The units of speed are m/s.
Learn more about work done : https://brainly.com/question/25573309
#SPJ11
According to relativity theory, if a space trip finds a child biologically older than their parents, then the space trip is taken by the:
A. Child
B. Parents
C. Cannot answer with the information given.
According to relativity theory, if a space trip finds a child biologically older than their parents, then the space trip is taken by the: A. Child
According to the theory of relativity, time dilation occurs when an object is moving at a significant fraction of the speed of light or in the presence of strong gravitational fields. This means that time can appear to pass differently for observers in different reference frames.
In the scenario described, if the space trip involves traveling at speeds close to the speed of light or in the presence of strong gravitational fields, time dilation effects could occur. As a result, the individuals on the space trip would experience time passing slower compared to those on Earth.
Therefore, if the child is on the space trip while the parents remain on Earth, the child would age slower relative to the parents. This means that when the space trip concludes and the child returns to Earth, they may be biologically younger than their parents, even though less time has passed for them.
To know mre about theory of relativity
https://brainly.com/question/32093861
#SPJ11
Coulomb's Law Two point charges Q. and Qz are 1.50 m apart, and their total charge is 15.4 wc. If the force of repulsion between them is 0.221 N, what are magnitudes of the two charges? Enter the smaller charge in the first box Q1 Q2 Submit Answer Tries 0/10 If one charge attracts the other with a force of 0.249N, what are the magnitudes of the two charges if their total charge is also 15.4 C? The charges are at a distance of 1.50 m apart. Note that you may need to solve a quadratic equation to reach your answer. Enter the charge with a smaller magnitude in the first box
Answer:
Since the product of the charges is known, we cannot determine the individual magnitudes of Q1 and Q2 to calculate the specific values of Q1 and Q2 separately.
Distance between the charges (r) = 1.50 m
Total charge (Q) = 15.4 C
Force of repulsion (F) = 0.221 N
According to Coulomb's Law, the force of repulsion between two point charges is given by:
F = k * (|Q1| * |Q2|) / r^2
Where F is the force,
k is the electrostatic constant,
|Q1| and |Q2| are the magnitudes of the charges, and
r is the distance between them.
Rearranging the equation, we can solve for the product of the charges:
|Q1| * |Q2| = (F * r^2) / k
Substituting the given values:
|Q1| * |Q2| = (0.221 N * (1.50 m)^2) / (9 x 10^9 N·m^2/C^2)
Simplifying the expression:
|Q1| * |Q2| ≈ 0.0495 x 10^-9 C^2
Since the product of the charges is known, we cannot determine the individual magnitudes of Q1 and Q2 with the provided information. The information given does not allow us to calculate the specific values of Q1 and Q2 separately.
Learn more about Coulomb's law here
https://brainly.com/question/26892767
#SPJ11
Q6. Explain what the difference is between an
asteroid, a rocky planet, a gas giant, a brown dwarf and a star.
[10 pts]
Asteroids, rocky planets, gas giants, brown dwarfs, and stars are all different celestial objects in the universe. Each of these objects has different characteristics that distinguish them from one another.
The difference between an asteroid, a rocky planet, a gas giant, a brown dwarf, and a star are explained below.
Asteroids: Asteroids are small, rocky objects that orbit the Sun. They are too small to be classified as planets, but too large to be classified as meteoroids. Most asteroids are found in the asteroid belt between Mars and Jupiter.
Some of the largest asteroids in the asteroid belt are Ceres, Vesta, and Pallas.
Rocky Planets: Rocky planets are terrestrial planets that are composed primarily of rock and metal. They have solid surfaces and are relatively small compared to gas giants.
The rocky planets in our solar system are Mercury, Venus, Earth, and Mars.Gas Giants: Gas giants are planets that are composed primarily of hydrogen and helium. They are much larger than rocky planets and have thick atmospheres. The gas giants in our solar system are Jupiter, Saturn, Uranus, and Neptune.
Brown Dwarfs: Brown dwarfs are objects that are too small to be stars, but too large to be gas giants. They are also known as failed stars because they do not have enough mass to sustain nuclear fusion in their cores.
Stars: Stars are massive, luminous objects that are held together by gravity.
They generate energy through nuclear fusion in their cores. There are many different types of stars, ranging from small red dwarfs to massive blue giants. The Sun is a typical yellow dwarf star.
Asteroids, rocky planets, gas giants, brown dwarfs, and stars are all different celestial objects with unique characteristics. Asteroids are small, rocky objects that orbit the Sun.
Rocky planets are terrestrial planets that are composed primarily of rock and metal, while gas giants are planets that are composed primarily of hydrogen and helium.
Brown dwarfs are objects that are too small to be stars, but too large to be gas giants, and stars are massive, luminous objects that generate energy through nuclear fusion in their cores. Understanding the differences between these celestial objects is important for astronomers to study the universe and its history.
To know more about nuclear fusion :
brainly.com/question/14019172
#SPJ11
Alternating current have voltages and currents through
the circuit elements that vary as a function of time. Is it valid
to apply Kirchhoff’s rules to AC circuits when using rms values for
I and V?
Kirchhoff's rules can be applied to AC circuits using rms values for current and voltage. RMS values represent the effective values, allowing analysis of current distribution and voltage drops in AC circuits.
It is valid to apply Kirchhoff's rules to AC circuits when using rms (root mean square) values for current (I) and voltage (V). Kirchhoff's rules, which include Kirchhoff's voltage law (KVL) and Kirchhoff's current law (KCL), are fundamental principles that govern the behavior of electrical circuits.
The rms values of current and voltage represent the effective values of the alternating current or voltage. They are calculated as the square root of the average of the squares of the instantaneous values over a complete cycle. By using rms values, we can treat AC circuits in a similar manner to DC circuits.
Kirchhoff's rules state that the algebraic sum of currents at any node in a circuit is zero (KCL), and the algebraic sum of voltages in any closed loop of a circuit is zero (KVL). These rules hold true for AC circuits because they are based on the conservation of charge and energy.
By using rms values, we can effectively analyze and solve AC circuits using Kirchhoff's rules, allowing us to determine current distribution, voltage drops, and power calculations in AC circuits.
To know more about Kirchhoff's rules,
https://brainly.com/question/31824235
#SPJ11
You have a string with a mass of 0.0121 kg. You stretch the string with a force of 9.97 N, giving it a length of 1.91 m. Then, you vibrate the string transversely at precisely the frequency that corresponds to its fourth normal mode; that is, at its fourth harmonic. What is the wavelength λ4 of the standing wave you create in the string? What is the frequency f4?
The wavelength (λ₄) of the standing wave created in the string at its fourth harmonic is approximately 7.64 m, and the frequency (f₄) is approximately 3.30 Hz.
To find the wavelength (λ₄) and frequency (f₄) of the standing wave in the string at its fourth harmonic, we can follow these steps:
1. Calculate the velocity of the wave on the string.
The velocity (v) of the wave can be determined using the formula:
v = √(Tension / Linear mass density),
where Tension is the applied force and Linear mass density is the mass per unit length of the string.
Force (Tension) = 9.97 N
Mass of the string = 0.0121 kg
Length of the string = 1.91 m
The linear mass density (μ) can be defined as the ratio of mass to length.
μ = 0.0121 kg / 1.91 m = 0.00633 kg/m
Substituting the values into the formula:
v = √(9.97 N / 0.00633 kg/m)
v ≈ 25.24 m/s
2. Determine the wavelength (λ₄) of the standing wave.
At the fourth harmonic, the wavelength is equal to four times the length of the string:
λ₄ = 4 * Length of the string
λ₄ = 4 * 1.91 m
λ₄ ≈ 7.64 m
3. Calculate the frequency (f₄) of the standing wave.
f = v / λ,
where v is the velocity and λ is the wavelength.
Substituting the values:
f₄ = 25.24 m/s / 7.64 m
f₄ ≈ 3.30 Hz
Therefore, the wavelength (λ₄) of the standing wave created in the string at its fourth harmonic is approximately 7.64 m, and the frequency (f₄) is approximately 3.30 Hz.
Learn more about wavelength at: https://brainly.com/question/10750459
#SPJ11
Two wires that have different linear mass densities, Mi = 0.45 kg/m and M2 = 0.27 kg/m , are spliced together. They are then used as a guy line to secure a telephone pole. Part A If the tension is 300 N, what is the difference in the speed of a wave traveling from one wire to the other?
we need to consider the wave speed equation and the relationship between tension, linear mass density, and wave speed.
Therefore, the difference in speed of a wave traveling from one wire to the other is approximately 7.52 m/s
The wave speed (v) on a string is given by the equation:
v = √(T/μ)
where T is the tension in the string and μ is the linear mass density of the string.
For the first wire with linear mass density M₁ = 0.45 kg/m and tension
T = 300 N, the wave speed v₁ is given by:
v₁ = √(T/M₁)
Similarly, for the second wire with linear mass density M₂ = 0.27 kg/m and tension T = 300 N, the wave speed v₂ is given by:
v₂ = √(T/M₂)
To calculate the difference in speed between the two wires, we subtract the smaller wave speed from the larger wave speed:
Δv = |v₁ - v₂| = |√(T/M₁) - √(T/M₂)|
Substituting the given values:
Δv = |√(300/0.45) - √(300/0.27)|
Δv = |√(666.67) - √(1111.11)|
Δv = |25.81 - 33.33|
Δv ≈ 7.52 m/s
Therefore, the difference in speed of a wave traveling from one wire to the other is approximately 7.52 m/s.
Learn more about tension here
https://brainly.com/question/14177858
#SPJ11
A 3 kg wooden block is being pulled across a flat table by a single attached rope. The rope has a tension of 6 N and is angled 18 degrees above the horizontal. The coefficient of kinetic friction between the block and the table is unknown. At t = 0.6 seconds, the speed of the block is 0.08 m/s. Later, at t = 1.3 seconds, the speed of the block is 0.16 m/s. What is the total work done by the surroundings on the wooden block between t = 0.6 seconds and t = 1.3 seconds?
The total work done by the surroundings on the wooden block between t = 0.6 seconds and t = 1.3 seconds is 0.0288 Joules.
To calculate the total work done by the surroundings on the wooden block between t = 0.6 seconds and t = 1.3 seconds, we need to consider the change in kinetic energy of the block during that time interval. The work done can be calculated using the work-energy principle;
Total Work = Change in Kinetic Energy
The change in kinetic energy can be determined by calculating the difference between the final and initial kinetic energies of the block. The initial kinetic energy can be calculated using the initial speed of the block, and the final kinetic energy can be calculated using the final speed of the block.
Initial Kinetic Energy = (1/2) × mass × initial velocity²
Final Kinetic Energy = (1/2) × mass × final velocity²
Given;
Mass of the wooden block (m) = 3 kg
Initial speed of the block (v₁) = 0.08 m/s
Final speed of the block (v₂) = 0.16 m/s
Let's calculate the total work done by the surroundings on the wooden block;
Initial Kinetic Energy = (1/2) × 3 kg × (0.08 m/s)²
Final Kinetic Energy = (1/2) × 3 kg × (0.16 m/s)²
Change in Kinetic Energy = Final Kinetic Energy - Initial Kinetic Energy
Total Work = Change in Kinetic Energy
Now, let's calculate the values;
Initial Kinetic Energy = (1/2) × 3 kg × (0.08 m/s)² = 0.0096 J
Final Kinetic Energy = (1/2) × 3 kg × (0.16 m/s)² = 0.0384 J
Change in Kinetic Energy = 0.0384 J - 0.0096 J = 0.0288 J
Therefore, the total work done by the surroundings on the wooden block between t = 0.6 seconds and t = 1.3 seconds is 0.0288 Joules.
To know more about total work done here
https://brainly.com/question/31430904
#SPJ4
Objective: Go through a few problems involving Newton's Laws and friction! Tasks (10 points) 1. Find the mass of a 745 N person and find the weight of an 8.20 kg mass. Use metric units! What is known? What is unknown? What is the basic equation? What is the working equation? Plug in your values. 2. A 2000 kg car is slowed down uniformly from 20.0 m/s to 5.00 m/s in 4.00 seconds. a. What average force acted on the car during that time? What is known? What is unknown? What is the basic equation? What is the working equation? Plug in your values. What is the answer? b. How far did the car travel during that time? What is known? What is unknown? What is the basic equation? What is the working equation? Plug in your values. What is the answer? 3. A 38.4-pound block sits on a level surface, and a horizontal 21.3-pound force is applied to the block. If the coefficient of static friction between the block and the surface is 0.75, does the block start to move? Hint: it may help to draw a force diagram to visualize where everything is happening. What is known? What is unknown? What is the basic equation? What is the working equation? Plug in your values. What is the answer?
The average force acted on the car during the deceleration is 7500 N.The car traveled a distance of 60 meters during the deceleration.The block does not start to move because the applied force is not sufficient to overcome the static friction.
To find the mass of a person given their weight, we use the equation weight = mass × gravity, where weight is given as 745 N. Solving for mass, we have mass = weight / gravity. Assuming standard gravity of 9.8 m/s², the mass is approximately 75.7 kg. To find the weight of a mass, we use the equation weight = mass × gravity, where mass is given as 8.20 kg. Plugging in the values, we have weight = 8.20 kg × 9.8 m/s², which gives a weight of approximately 80.2 N.
2a. To find the average force acting on the car during deceleration, we use Newton's second law, which states that force = mass × acceleration. The change in velocity is 20.0 m/s - 5.00 m/s = 15.0 m/s, and the time is given as 4.00 seconds. The acceleration is calculated as change in velocity / time, which is 15.0 m/s / 4.00 s = 3.75 m/s². Plugging in the mass of 2000 kg and the acceleration, we have force = 2000 kg × 3.75 m/s² = 7500 N.
2b. To determine the distance the car traveled during deceleration, we can use the equation of motion x = x₀ + v₀t + 0.5at². Since the car is slowing down, the final velocity is 5.00 m/s, the initial velocity is 20.0 m/s, and the time is 4.00 seconds. Plugging in these values and using the equation, we get x = 0 + 20.0 m/s × 4.00 s + 0.5 × (-3.75 m/s²) × (4.00 s)² = 60 meters.
To determine if the block starts to move, we need to compare the applied force to the maximum static friction. The equation for static friction is fs ≤ μs × N, where fs is the force of static friction, μs is the coefficient of static friction, and N is the normal force. The normal force is equal to the weight of the block, which is given as 38.4 pounds. Converting the weight to Newtons, we have N = 38.4 lb × 4.45 N/lb = 171.12 N. Plugging in the values, we have fs ≤ 0.75 × 171.12 N. Since the applied force is 21.3 pounds, which is less than the maximum static friction, the block does not start to move.
Learn more about static friction here:
https://brainly.com/question/17140804
#SPJ11
Question 32 (1 point) Vibrations at an angle of 90° to the direction of propagation are waves. Question 33 (1 point) The intensity of a sound at 200 m is A times less than the intensity of sound at 100 m. Question 34 (1 point) Sounds above the sonic frequency range of humans are known as A and below the sonic frequency range the sound are called A/ Question 35 (1 point) The number of cycles per second a sound wave delivers to the ear is its A to a physicist but musicians or the general public refer to this as Question 36 (1 point) The Doppler effect is associated with the difference in A heard when a source of sound and the ear are moving relative to each other.
Answer: Only statement 32 is false.
32: Vibrations at an angle of 90° to the direction of propagation are waves.
This statement is false. The vibrations which are perpendicular to the direction of propagation of the wave is known as a transverse wave. The vibrations which are in the direction of propagation of the wave are known as longitudinal waves.
33: The intensity of a sound at 200 m is A times less than the intensity of sound at 100 m.
This is true. The intensity of sound is inversely proportional to the square of the distance from the source. Therefore, if the distance is doubled, then the intensity decreases by four times, hence A times less than the intensity of the sound at 100 m.
34: Sounds above the sonic frequency range of humans are known as ultrasonic and below the sonic frequency range the sound are called infrasonic.
This statement is true. Infrasonic waves are the waves with frequencies less than 20 Hz whereas the waves with frequencies greater than 20 kHz are known as ultrasonic waves.
35: The number of cycles per second a sound wave delivers to the ear is its frequency to a physicist but musicians or the general public refer to this as pitch.
This statement is true. The number of cycles per second of a sound wave is its frequency which is measured in hertz. Pitch is how high or low a sound is and it is usually associated with the frequency of the sound wave.
36: The Doppler effect is associated with the difference in frequency heard when a source of sound and the ear are moving relative to each other.
This statement is true. The Doppler effect is the change in frequency or wavelength of a wave in relation to an observer who is moving relative to the wave source. This effect is used in various applications like medical ultrasound, astronomical measurements, and weather radar systems.
Learn more about frequency : https://brainly.com/question/254161
#SPJ11
Three point charges q1=–4.63 µC, q2=5.43 µC and q_3 are position on the vertices of a square whose side length is 7.61 cm at point a, b, and c, respectively as shown in the figure below. The electric potential energy associated to the third charge q3 is 1.38 J. What is the charge carried by q3?
Therefore, the charge carried by q3 is 341 µC or -341 µC (since we don't know its sign).Answer: The charge carried by q3 is 341 µC.
We are given the side length of the square as 7.61 cm. Let's consider the position vector of q3 from q1. Its direction is along the diagonal of the square, and its magnitude can be calculated using Pythagoras theorem.
The distance of q3 from q1 is given by the hypotenuse of an isosceles right-angled triangle with legs of length 7.61 cm. Therefore, the distance from q1 to q3 is:r = √(7.61² + 7.61²) = 10.75 cmNext, let's calculate the electric potential energy between q1 and q3. Using the formula for electric potential energy of a pair of point charges:U = (k * |q1| * |q3|) / r
where k = 9 x 10^9 Nm²/C² is Coulomb's constant. We know U = 1.38 J, |q1| = 4.63 µC, and r = 10.75 cm. Substituting these values and solving for |q3|:|q3| = (U * r) / (k * |q1|) = (1.38 J * 10.75 cm) / (9 x 10^9 Nm²/C² * 4.63 µC)= 0.000341 C = 341 µC
Therefore, the charge carried by q3 is 341 µC or -341 µC (since we don't know its sign).Answer: The charge carried by q3 is 341 µC.
to know more about diagonal
https://brainly.com/question/5426789
#SPJ11
A coil has 150 turns enclosing an area of 12.9 cm2 . In a physics laboratory experiment, the coil is rotated during the time interval 0.040 s from a position in which the plane of each turn is perpendicular to Earth's magnetic field to one in which the plane of each turn is parallel to the field. The magnitude of Earth's magnetic field at the lab location is 5.40×10−5T .
Part A: What is the magnitude of the magnetic flux through one turn of the coil before it is rotated?
Express your answer in webers.
Part B: What is the magnitude of the magnetic flux through one turn of the coil after it is rotated?
Express your answer in webers.
A coil has 150 turns enclosing an area of 12.9 cm2 . the magnitude of the magnetic flux through one turn of the coil before it is rotated is approximately 6.9564 × 10^−9 Weber. the magnitude of the magnetic flux through one turn of the coil after it is rotated is also approximately 6.9564 × 10^−9 Weber.
Part A: To calculate the magnitude of the magnetic flux through one turn of the coil before it is rotated, we can use the formula:
Φ = B * A * cos(θ),
where Φ is the magnetic flux, B is the magnetic field, A is the area, and θ is the angle between the magnetic field and the normal to the coil.
Since the plane of each turn is initially perpendicular to Earth's magnetic field, the angle θ is 90 degrees. Substituting the given values, we have:
Φ = (5.40×10^−5 T) * (12.9 cm^2) * cos(90°).
Note that we need to convert the area to square meters to match the units of the magnetic field:
Φ = (5.40×10^−5 T) * (12.9 × 10^−4 m^2) * cos(90°).
Simplifying the equation, we find:
Φ = 6.9564 × 10^−9 Wb.
Therefore, the magnitude of the magnetic flux through one turn of the coil before it is rotated is approximately 6.9564 × 10^−9 Weber.
Part B: After the coil is rotated, the plane of each turn becomes parallel to the magnetic field. In this case, the angle θ is 0 degrees, and the cosine of 0 degrees is 1. Therefore, the magnetic flux through one turn remains the same as in Part A:
Φ = 6.9564 × 10^−9 Wb.
Hence, the magnitude of the magnetic flux through one turn of the coil after it is rotated is also approximately 6.9564 × 10^−9 Weber.
Learn more about magnetic field here:
https://brainly.com/question/30331791
#SPJ11
A tiny sphere of mass 7. 70mg and charge −2. 80nC is initially at a distance of 1. 64μm from a fixed charge of +7. 65nC. (a) If the 7. 70-mg sphere is released from rest, find its kinetic energy when it is 0. 500μm from the fixed charge. × J (b) If the 7. 70-mg sphere is released from rest, find its speed when it is 0. 500μm from the fixed charge. M/s
The kinetic energy of the sphere and its speed can be calculated using the principle of conservation of mechanical energy and the principle of conservation of energy, respectively.
The kinetic energy of the tiny sphere can be found using the principle of conservation of mechanical energy. Initially, the sphere has gravitational potential energy only, given by PE = mgh, where m is the mass (7.70mg), g is the acceleration due to gravity (9.8 m/s²), and h is the initial height (1.64μm).
The final kinetic energy can be calculated by subtracting the final gravitational potential energy (mgh) from the initial potential energy.
At a distance of 0.500μm from the fixed charge, the height can be calculated as h' = (1.64μm - 0.500μm) = 1.14μm.
The final kinetic energy (KE) can be calculated using KE = PE - mgh' where h' is the final height (1.14μm).
To find the speed of the sphere when it is 0.500μm from the fixed charge, we can use the principle of conservation of energy. The initial mechanical energy is equal to the final mechanical energy.
The initial mechanical energy is given by the sum of the initial gravitational potential energy (mgh) and the initial electric potential energy (kQq/r), where k is the Coulomb constant (8.99 x 10⁹ Nm²/C²), Q is the charge of the fixed charge (+7.65nC), q is the charge of the sphere (-2.80nC), and r is the initial distance (1.64μm).
The final mechanical energy is given by the final kinetic energy (KE) and the final electric potential energy (kQq/r'), where r' is the final distance (0.500μm).
Setting the initial mechanical energy equal to the final mechanical energy, we can solve for the speed of the sphere when it is 0.500μm from the fixed charge.
To summarize:
(a) The kinetic energy of the sphere when it is 0.500μm from the fixed charge can be found by subtracting the final gravitational potential energy from the initial potential energy.
(b) The speed of the sphere when it is 0.500μm from the fixed charge can be calculated using the principle of conservation of energy, setting the initial mechanical energy equal to the final mechanical energy.
Conclusion, The kinetic energy of the sphere and its speed can be calculated using the principle of conservation of mechanical energy and the principle of conservation of energy, respectively.
To know more about mechanical energy visit:
https://brainly.com/question/29509191
#SPJ11
Vector A = 26.0 North
Vector B = 35.0 East
Vector C = 23.0 West
Find the direction of the resultant for A - B. (3 significant figures)
The direction of the resultant vector for A - B is 35.6° West of North.
Vector A = 26.0 North
Vector B = 35.0 East
Vector C = 23.0 West
The direction of the resultant for A - B will be as follows:
Vector A and Vector B are perpendicular to each other, as Vector A is in the North direction and Vector B is in the East direction.
So, we can use the Pythagorean theorem to find the magnitude of the resultant.
Thus, Resultant vector,
R² = A² + B²
R = √(A² + B²)
R = √(26² + 35²)
R = 43.55 units (approx)
As we know that Vector A and Vector B are perpendicular to each other, the angle between them will be 90°.
Now, we can use trigonometric ratios to find the direction of the resultant vector,
tan θ = opposite side/adjacent side
tan θ = A/B
tan θ = 26/35
θ = 35.61° (approx)
Hence, the direction of the resultant vector for A - B is 35.6° West of North (3 significant figures).
Learn more about the vectors:
brainly.com/question/30914052
#SPJ11
When the frequency of the AC voltage is doubled, the capacitive reactance whille the inductive reactance halves; doubles doubles; halves halves; halves doubles; doubles
When the frequency of the AC voltage is doubled, the capacitive reactance halves while the inductive reactance doubles.
When the frequency of the AC voltage is doubled, the capacitive reactance halves while the inductive reactance doubles. This is because the reactance of a capacitor is inversely proportional to the frequency of the AC voltage, while the reactance of an inductor is directly proportional to the frequency of the AC voltage.Capacitive reactance, denoted by XC, is given by the formula:XC = 1 / (2πfC)Where f is the frequency of the AC voltage, and C is the capacitance of the capacitor.
Since the reactance of the capacitor is inversely proportional to the frequency of the AC voltage, when the frequency of the AC voltage is doubled, the capacitive reactance will be halved.On the other hand, inductive reactance, denoted by XL, is given by the formula:XL = 2πfLWhere f is the frequency of the AC voltage, and L is the inductance of the inductor. Since the reactance of the inductor is directly proportional to the frequency of the AC voltage, when the frequency of the AC voltage is doubled, the inductive reactance will be doubled.
In conclusion, when the frequency of the AC voltage is doubled, the capacitive reactance halves while the inductive reactance doubles.
Learn more about frequency here,
https://brainly.com/question/254161
#SPJ11
An electric iron is Marg 20 words 500 w the units consumed by it in using it for 24 hours will be
The electric iron with a power rating of 500 watts will consume 12 kilowatt-hours (kWh) of electricity when used continuously for 24 hours.
To calculate the units consumed, we need to consider the power rating and the duration of usage. The power rating of the electric iron is given as 500 watts, which is equivalent to 0.5 kilowatts (kW). By multiplying the power rating by the time used (24 hours), we obtain the total energy consumed, which is 12 kilowatt-hours (kWh). This value represents the units of electricity consumed by the electric iron during the 24-hour period.
Therefore, the electric iron will consume 12 kilowatt-hours (kWh) of electricity when used for 24 hours continuously with a power rating of 500 watts.
Know more about kilowatt here:
brainly.com/question/24057012
#SPJ11
An insulated beaker with negligible mass contains liquid water with a mass of 0.230 kg and a temperature of 83.7°C. Part A
How much ice at a temperature of −10.2°C must be dropped into the water so that the final temperature of the system will be 29.0°C ? Take the specific heat of liquid water to be 4190 J/kg·K, the specific heat of ice to be 2100 J/kg·K, and the heat of fusion for water to be 3.34×10⁵ J/kg.
0.109 kg of ice at a temperature of −10.2°C must be dropped into the water so that the final temperature of the system will be 29.0°C.
Mass of water = 0.230 kg
Initial temperature of water = 83.7°C
Specific heat of liquid water = 4190 J/kg·K
Specific heat of ice = 2100 J/kg·K
Heat of fusion for water = 3.34×10⁵ J/kg.
Final temperature of the system = 29.0°C.
The heat released by water = heat absorbed by ice
So, m1c1∆T1 = m2c2∆T2 + mL1where, m1 = Mass of water, m2 = Mass of ice, L1 = Heat of fusion of ice, c1 = Specific heat of water, c2 = Specific heat of ice, ∆T1 = (final temperature of system - initial temperature of water) = (29 - 83.7) = -54.7°C ∆T2 = (final temperature of system - initial temperature of ice) = (29 - (-10.2)) = 39.2°C
By substituting the values, we get: 0.230 × 4190 × (-54.7) = m2 × 2100 × 39.2 + m2 × 3.34×10⁵
On solving the above equation, we get: m2 = 0.109 kg
Therefore, 0.109 kg of ice at a temperature of −10.2°C must be dropped into the water so that the final temperature of the system will be 29.0°C.
Learn more about specific heat: https://brainly.com/question/27991746
#SPJ11
You have a circular loop of wire in the plane of the page with initial radius 1.0 m which shrinks to a radius of 1 m. It sits in a constant magnetic field B = 10T pointing into the page. Assume the transformation occurs over 10 seconds and no part of the wire exits the field. Also assume an internal resistance of 30 Ω. What average current is produced within the loop and in which direction?
a. 79 mA, CW
b. 79 mA, CCW
c. 701 mA, CCW
d. Zero
The average current that is produced within the loop is zero.
option D.
What is the emf induced?The emf induced in the circuit is calculated by applying the following formula for electromagnetic induction as follows;
emf = NBA/t
where;
N is the number of turnsB is the constant magnetic fieldA is the area of the loopt is the timeThe area of the circular loop is calculated as;
A = π(r₁ - r₂)²
where;
r₁ is the initial radius
r₂ is the final radius
A = π (1² - 1²)
A = 0 m²
The induced emf is calculated as;
emf = (1 x 10T x 0 m² ) / ( 10 s )
emf = 0 V
The current produced is calculated as follows;
I = emf / R
I = 0 V / 30 Ω.
I = 0 A
Learn more about induced emf here: https://brainly.com/question/13744192
#SPJ4
(a) Show that when the recoil kinetic energy of the atom, p²/2M, is taken into account the frequency of a photon emitted in a transition between two atomic levels of energy difference AE is reduced by a factor which is approximately (1-AE/2Mc²). (Hint: The recoil momentum is p = hv/c.) (b) Compare the wavelength of the light emitted from a hydrogen atom in the 3→ 1 transition when the recoil is taken into account to the wave- length without accounting for recoil.
The frequency of photon emitted in a transition between two atomic energy levels is reduced by factor of approximately (1 - AE/2Mc²). Taking recoil into account affects the wavelength of light emitted from hydrogen atom in the 3 → 1 transition.
(a) We start with the equation for energy conservation: hf = AE + p²/2M,
We can express the recoil momentum as p = hv/c
hf = AE + (hv/c)²/2M.
hf = AE + hv²/(2Mc²).
Now, we can factor out hv²/2Mc² from the right-hand side:
hf = (1 + AE/(2Mc²)) * hv²/2Mc².
Therefore, the frequency of the emitted photon is reduced by a factor of approximately (1 - AE/2Mc²) when the recoil kinetic energy is taken into account.
(b) The wavelength of the emitted light can be related to the frequency by the equation λ = c/f.
Taking into account recoil, the reduced frequency is f₂ = f₁/(1 - AE/2Mc²).
Therefore, the wavelength of the light emitted when the recoil is considered is λ₂ = c/f₂ = c * (1 - AE/2Mc²) / f₁.
λ₂/λ₁ = (c * (1 - AE/2Mc²) / f₁) / (c/f₁) = 1 - AE/2Mc².
Hence, the ratio of the wavelengths with and without accounting for recoil is approximately (1 - AE/2Mc²).
Learn more about frequency here;
https://brainly.com/question/27151918
#SPJ11
Describe the three types of possible Universes we could live in and what will happen to them in the end. In your description, include the value of the cosmological density parameter and the size of the Universe in each case.
There are three types of possible universes based on the value of the cosmological density parameter. In a closed universe (Ω > 1), In an open universe (Ω < 1) & In a flat universe (Ω = 1).
The cosmological density parameter (Ω) represents the ratio of the actual density of matter and energy in the universe to the critical density required for the universe to be flat.
In a closed universe (Ω > 1), the density of matter and energy is high enough for the universe's gravitational pull to eventually overcome the expansion, leading to a collapse.
In an open universe (Ω < 1), the density of matter and energy is below the critical value, resulting in a universe that continues to expand indefinitely.
In a flat universe (Ω = 1), the density of matter and energy precisely balances the critical density, leading to a universe that expands at a gradually slowing rate.
Learn more about cosmological here;
https://brainly.com/question/31965795
#SPJ11
The capacitance of an empty capacitor is 4.70 μF. The capacitor is connected to a 12-V battery and charged up. With the capacitor connected to the battery, a slab of dielectric material is inserted between the plates. As a result, 9.30 × 10-5 C of additional charge flows from one plate, through the battery, and onto the other plate. What is the dielectric constant of the material?
The dielectric constant of the material is approximately 1.98.
To find the dielectric constant of the material, we can use the formula:
C' = κC
where C' is the capacitance with the dielectric material inserted, C is the original capacitance without the dielectric, and κ is the dielectric constant of the material.
Given:
C = 4.70 μF = 4.70 × 10^-6 F
Q = 9.30 × 10^-5 C
V = 12 V
The capacitance can also be expressed as:
C = Q / V
Rearranging the equation to solve for Q:
Q = C × V
Substituting the given values:
Q = (4.70 × 10^-6 F) × (12 V)
= 5.64 × 10^-5 C
The additional charge Q' is given as 9.30 × 10^-5 C.
Now, we can find the dielectric constant:
C' = κC
C' = Q' / V
κC = Q' /
κ = Q' / (CV)
κ = (9.30 × 10^-5 C) / [(4.70 × 10^-6 F) × (12 V)]
κ = 1.98
Therefore, the dielectric constant of the material is approximately 1.98.
Learn more about dielectric constant
https://brainly.com/question/32198642
#SPJ11
The light beam shown in the figure below makes an angle of a =20.2 ∘
with the normal line NN in the linseed oll. Determine the anale θ. (The refractive index for linseed oll is 1.48.)
The angle of refraction of the light beam in the linseed oil is approximately 12.5°.
The light beam shown in the figure below makes an angle of a = 20.2° with the normal line NN in the linseed oil. Determine the angle θ. (The refractive index for linseed oil is 1.48).
The angle of refraction (θ) of the given light beam can be calculated using Snell's law. According to Snell's law of refraction,n₁sinθ₁ = n₂sinθ₂Where, n₁ = refractive index of the first medium, i.e., air (or vacuum), θ₁ = angle of incidence of the light ray, n₂ = refractive index of the second medium, i.e., linseed oil, θ₂ = angle of refraction of the light ray.
In this case, the angle of incidence (θ₁) is 90° since it is perpendicular to the normal line NN. Therefore, sin θ₁ = 1. The refractive index (n₂) for linseed oil is 1.48. The angle of incidence (a) of the light ray with respect to the normal is 20.2°.
Thus, applying Snell's law of refraction,n₁sinθ₁ = n₂sinθ₂⇒ sin θ₂ = (n₁ / n₂) × sin θ₁⇒ sin θ = (1 / 1.48) × sin 20.2°≈ 0.2154⇒ θ ≈ sin⁻¹ 0.2154≈ 12.5°
Therefore, the angle of refraction of the light beam in the linseed oil is approximately 12.5°.
The angle of refraction (θ) is approximately 12.5°. The light beam shown in the figure below makes an angle of a = 20.2° with the normal line NN in the linseed oil. The refractive index for linseed oil is 1.48.
To learn about the refractive index here:
https://brainly.com/question/83184
#SPJ11
show the positioning of an objective lens and eye piece of the following devices with respect to their focal length . example d=fo-fe and number of lens in the device
1. simple microscopic (magnifying glass)
2. compound microscope
3. astronomical telescope
4. galilean telescope
5. prismatic binoculars
1. Simple Microscope (Magnifying Glass): Objective lens = N/A, Eyepiece = N/A (Single Lens)
2. Compound Microscope: Objective lens = Closer, Eyepiece = Farther
3. Astronomical Telescope: Objective lens = Closer, Eyepiece = Farther
4. Galilean Telescope: Objective lens = Closer, Eyepiece = Farther
5. Prismatic Binoculars: Objective lens = Closer, Eyepiece = Farther
Simple Microscope (Magnifying Glass):
In a simple microscope or magnifying glass, there is only one lens, which serves as both the objective lens and the eyepiece. The lens is convex and typically has a short focal length. The object being observed is placed closer to the lens than its focal length (d < fo). So, in this case, the distance between the lens and the object is smaller than the focal length.
Compound Microscope:
A compound microscope consists of two lenses: the objective lens and the eyepiece. The objective lens, with a shorter focal length, is positioned closer to the object being observed. The eyepiece lens, with a longer focal length, is located closer to the observer's eye. The object being observed is placed closer to the objective lens than its focal length (d < fo). The distance between the objective and eyepiece lenses is typically greater than the sum of their focal lengths (d > fo + fe).
Astronomical Telescope:
In an astronomical telescope, the objective lens is positioned closer to the object being observed, such as celestial bodies. The objective lens has a longer focal length compared to the eyepiece lens. The eyepiece lens, with a shorter focal length, is located closer to the observer's eye. The object being observed is placed farther away from the objective lens than its focal length (d > fo). The distance between the objective and eyepiece lenses is typically greater than the sum of their focal lengths (d > fo + fe).
Galilean Telescope:
A Galilean telescope has a convex objective lens and a concave eyepiece lens. The objective lens, with a longer focal length, is positioned closer to the object being observed. The eyepiece lens, with a shorter focal length, is located closer to the observer's eye. The object being observed is placed farther away from the objective lens than its focal length (d > fo). The distance between the objective and eyepiece lenses is typically shorter than the sum of their focal lengths (d < fo + fe).
Prismatic Binoculars:
Prismatic binoculars use multiple lenses and prisms to provide a magnified view. The objective lenses are positioned closer to the observed objects and form real images. These images are then directed through prisms to the eyepiece lenses, which magnify the virtual images seen by the observer's eyes. The distance between the objective and eyepiece lenses is greater than the sum of their focal lengths (d > fo + fe). Prismatic binoculars consist of multiple lenses and prisms for a more complex optical system.
Know more about magnifying glass here:
https://brainly.com/question/20876425
#SPJ8
A particle with a mass two times that of an electron is moving at a speed of 0.880c. (a) Determine the speed (expressed as a multiple of the speed of light) of a neutron that has the same kinetic energy as the particle. When calculating gamma factors, keep values to six places beyond the decimal point and then round your final answer to three significant figures.
_______________ c (b) Determine the speed (expressed as a multiple of the speed of light) of a neutron that has the same momentum as the particle. When calculating gamma factors, keep values to six places beyond the decimal point and then round your final answer to three significant figures.
_______________ c
(a) The speed of a neutron with the same kinetic energy as the particle is 0.03 c.
(b) The speed of the neutron with same momentum is 0.00096 c.
What is the speed of the neutron?(a) The speed of a neutron with the same kinetic energy as the particle is calculated as follows;
Kinetic energy of the particle;
K.E = ¹/₂mv²
where;
m is the mass of the particlev is the speed of the particleK.E = ¹/₂ x (2 x 9.11 x 10⁻³¹) (0.88c)²
K.E = 7.05 x 10⁻³¹c²
The speed of the neutron is calculated as;
v² = 2K.E / m
v = √ (2 x K.E / m )
v = √ ( 2 x 7.05 x 10⁻³¹c² / 1.67 x 10⁻²⁷ )
v = 0.03 c
(b) The speed of the neutron with same momentum is calculated as;
v₂ = (m₁v₁) / m₂
v₂ = ( 2 x 9.11 x 10⁻³¹ x 0.88c) / ( 1.67 x 10⁻²⁷)
v₂ = 0.00096 c
Learn more about momentum here: https://brainly.com/question/7538238
#SPJ4
Lateral magnification by the objective of a simple compound microscope is. m 1
=−10×. Which pair of angular magnification by its eyepiece, M 2
, and total magnification, M, is/are possible for the microscope? 14. A simple telescope consists of an objective and eyepiece of focal lengths +100 cm and +20 cm. Which of the following is/are TRUE about the telescope? A. The telescope length is 1.2 m. B. The power of the objective is +1.0D C. The final image formed by the telescope is virtual. 15. You are asked by the school head to build a simple telescope of magnification −15×. Which pair of lens combinations is/are suitable for the telescope? 16. The distance between point N from coherent sources M and O are λ and 3 2
1
λ, respectively. Points M,N and O lie in a straight line. Point N is located between M and O. Which is/are true statement(s) about the situation. A. Point N is an antinode point. B. The path length between source M and O is 4 2
1
λ. C. The path difference between sources M and O at point N is 2 2
1
λ 17. A bubble seems to be colourful when shone with white light. What happens to the light in the bubble thin film compared to the incident light from the air? A. The light is slower in the thin film. B. The wavelength of the light is shorter in the film. C. The frequency of the light does not change in the film. 18. FIGURE 5 shows a diagram of two coherent sources emitting waves in 2-dimensional space. Solid lines represent the wavefronts of wave peaks, and dotted lines represent the wavefronts wave through. Select the thick line(s) representing the nodal line(s). 19. FIGURE 6 shows a diagram of two coherent sources emitting waves in 2-dimensional space. Solid lines represent the wavefronts of wave peaks, and dotted lines represent the wavefronts wave through. 20. A part of a static bubble in the air momentarily looks reddish under the white light illumination. Given that the refractive index of the bubble is 1.34 and the red light wavelength is 680 nm, what is/are the possible bubble thickness? A. 130 nm B. 180 nm C. 630 nm 21. A thin layer of kerosene (n=1.39) is formed on a wet road (n=1.33). If the film thickness is 180 nm, what is/are the possible visible light seen on the layer? A. 460 nm B. 700 nm C. 1400 nm 22. 400 nm blue light passes through a diffraction grating. The first order bright fringe is located at 10 mm from the central bright. Which of the following is/are true about the situation? A. The width of the bright fringe is 10 cm. B. The distance between consecutive bright fringe is 10 cm. C. The distance between the light source and the screen is 10 cm. 23. In Young's double slits experiment, A. the slits refract light. B. the wavelength of the light source increases and decreases alternatively. C. the width of the central bright is inversely proportional to the distance between slits. 24. A beam of monochromatic light is diffracted by a slit of width 0.45 mm. The diffraction pattern forms on a wall 1.5 m beyond the slit. The width of the central maximum is 2.0 mm. Which of the following is/are TRUE about the experiment? A. The wavelength of the light is 600 nm. B. The width of each bright fringe is 2.0 mm C. The distance between dark fringes is 1.0 mm Devi conducted a light diffraction experiment using a red light. She got the diffraction pattern as shown in FIGURE 7. The distance between indicated dark fringes was measured as 2.5 mm. Which of the following statement is/are TRUE about the experiment? A. She used diffraction grating to get the pattern. B. The width of the central maximum was 2.5 mm. C. The distance between consecutive bright fringes was 2.5 mm.
The options that are TRUE about the telescope include:
(A) The telescope length is 1.2 m.
(C) The final image formed by the telescope is virtual.
How to explain the informationThe telescope length is the sum of the focal lengths of the objective and eyepiece, so it is 1.2 m. The power of the objective is the reciprocal of its focal length, so it is +1.0D. The final image formed by a telescope is always virtual.
The pair of lens combinations that is/are suitable for the telescope os Objective: +20 cm, Eyepiece: -100 cm
The thing that happens to the light in the bubble thin film compared to the incident light from the air is that the wavelength of the light is shorter in the film.
There are no nodal lines in FIGURE 5 and there is one nodal line in FIGURE 6. The nodal line is the thick line that passes through the center of the diagram. At this point, the waves from the two sources are exactly out of phase. So, there is no light at this point.
Learn more about telescope on
https://brainly.com/question/18300677
#SPJ4
Find the current density of a copper wire with a diameter of 6.4 m and carries a constant current of 9.6 A to a 150-W lamp.
Therefore, the current density of the copper wire is 3.23 × 104 A/m2.How did you find this solution helpful? Let us know by leaving a comment below!
Current density of a copper wire with a diameter of 6.4 mm and carries a constant current of 9.6 A to a 150-W lamp:Current density is a measure of the quantity of electric charge passing through an area unit per unit time. When a wire of cross-sectional area A carries an electric current I,
the current density J is given by J = I/A. Here, the current density J = ?I/A, where I = 9.6 A is the current flowing in the copper wire and A = 3.22 × 10-8 m2 is the cross-sectional area of the wire. Since the wire is made of copper, which has a density of 8.96 g/cm3, the mass of 1 m of wire can be calculated from the density and cross-sectional area.Mass per metre of wire = Density x Cross-sectional area = 8.96 g/cm3 x 3.22 × 10-8 m2 = 2.89 × 10-6 g/m
The number of moles of copper in 1 m of wire is calculated as follows:Amount of copper = Mass of copper/Molar mass of copper = 2.89 × 10-6 g/63.55 g/mol = 4.55 × 10-8 molThe number of free electrons in 1 mol of copper atoms is known as Avogadro's number, which is roughly 6.02 × 1023. As a result,
the total number of free electrons in 1 m of copper wire can be calculated by multiplying Avogadro's number by the number of moles of copper in 1 m of wire, which is given as:Number of free electrons per metre of wire = Avogadro's number x Amount of copper = 6.02 × 1023 × 4.55 × 10-8 = 2.74 × 1016
The amount of electric charge, q, that passes through the wire per unit time is given by q = It, where t is the time for which the current flows. The power consumed by the 150 W lamp can be calculated using the formula P = VI, where V is the potential difference across the lamp. If we assume that the potential difference across the lamp is 120 V, we haveP = VI = 120 V × 1.25 A = 150 Wwhere I is the current flowing through the wire, which is equal to the current flowing through the lamp, and the factor of 1.25 takes into account the power losses in the circuit.
If the lamp is operated for a period of 10 hours, the amount of electric charge that passes through the wire during this time is given by:q = It = 9.6 A x 10 h x 3600 s/h = 3.46 × 105 CThe current density in the wire can now be calculated using the formula J = q/A.t. Therefore,Current density of copper wire = J = q/A.t = (3.46 × 105 C)/(3.22 × 10-8 m2 x 10 x 3600 s) = 3.23 × 104 A/m2
Therefore, the current density of the copper wire is 3.23 × 104 A/m2.How did you find this solution helpful? Let us know by leaving a comment below!
to know more about density
https://brainly.com/question/1354972
#SPJ11
1.38 Compute the energy of the following signals. (a) x₁(t) = eat u(t) for a > 0 (b) x2(t) = eat for a > 0 (c) x3(t) = (1 - [t]) rect(1/2)
The energy of signal x₃(t) is 5.
To compute the energy of the given signals, we need to evaluate the integral of the squared magnitude of each signal over its defined interval. Here's how we can calculate the energy for each signal:
(a) x₁(t) = eat u(t) for a > 0
To calculate the energy of x₁(t), we need to integrate |x₁(t)|² over its interval.
∫(|x₁(t)|²) dt = ∫((eat u(t))²) dt
= ∫(e^2at u(t)) dt
Since the signal x₁(t) is defined for t ≥ 0, we can integrate from 0 to infinity:
∫(|x₁(t)|²) dt = ∫(e^2at) dt from 0 to infinity
= [(-1/2a) * e^2at] from 0 to infinity
= (-1/2a) * (e^2a(infinity) - e^2a(0))
= (-1/2a) * (0 - 1)
= 1/(2a)
So, the energy of x₁(t) is 1/(2a).
(b) x₂(t) = eat for a > 0
To calculate the energy of x₂(t), we integrate |x₂(t)|² over its interval.
∫(|x₂(t)|²) dt = ∫((eat)²) dt
= ∫(e^2at) dt
Again, since the signal x₂(t) is defined for t ≥ 0, we integrate from 0 to infinity:
∫(|x₂(t)|²) dt = ∫(e^2at) dt from 0 to infinity
= [(-1/2a) * e^2at] from 0 to infinity
= (-1/2a) * (e^2a(infinity) - e^2a(0))
= (-1/2a) * (0 - 1)
= 1/(2a)
The energy of x₂(t) is also 1/(2a).
(c) x₃(t) = (1 - [t]) rect(1/2)
To calculate the energy of x₃(t), we integrate |x₃(t)|² over its interval.
∫(|x₃(t)|²) dt = ∫((1 - [t])² rect(1/2)²) dt
= ∫((1 - [t])² (1/4)) dt
Since the signal x₃(t) is defined for 0 ≤ t ≤ 1, we integrate from 0 to 1:
∫(|x₃(t)|²) dt = ∫((1 - [t])² (1/4)) dt from 0 to 1
= ∫((1 - t)² (1/4)) dt from 0 to 1
= (1/4) ∫((1 - 2t + t²)) dt from 0 to 1
= (1/4) [t - t²/2 + t³/3] from 0 to 1
= (1/4) [(1 - 1/2 + 1/3) - (0 - 0 + 0)]
= (1/4) [(6/6 - 3/6 + 2/6)]
= (1/4) [5/6]
= 5/24
Therefore, the energy of x₃(t) is 5
To learn more about Signal energy, visit:
https://brainly.com/question/2622778
#SPJ11
A block of a clear, glass-ike material sits on a table surrounded by normal air (you may assume r=1.00 in air). A beam of light is incident on the block at an angle of 40.8 degrees. Within the block, the beam is observed to be at an angle of 22 8 degrees from the normal. What is the speed of light in this material? The answer appropriately rounded, will be in the form (X)x 10 m/s. Enter the number (X) rounded to two decimal places
The speed of light in a material can be determined using the relation:
n1 sin(θ1) = n2 sin(θ2),
where n1 = 1 in air (since it is given that r = 1.00 in air) and θ1 = 40.8 degrees (the angle of incidence).
The angle of refraction, θ2, is given as 22.8 degrees.
To find the refractive index, n2, we use:
n2 = n1 sin(θ1)/ sin(θ2)
n2 = sin(40.8)/sin(22.8)
= 1.6 (rounded to one decimal place)
The speed of light in the material can be found using:
v = c/n2, where c is the speed of light in vacuum
v = c/1.6 = 1.875x10^8 m/s (rounded to two decimal places)
Therefore, the speed of light in the material is 1.88 x 10^8 m/s (rounded to two decimal places).
Answer: 1.88
Learn more about speed of light here
https://brainly.com/question/104425
#SPJ11