The grams of HNO3 in 80 mL of the 70% HNO3 solution is approximately 80 g.
To calculate the grams of HNO3 in 80 mL of a 70% (by mass) HNO3 solution, we can follow these steps:
Step 1: Convert the volume of the solution to grams.
Density = 1.42 g/mL
Volume of solution = 80 mL
Mass of solution = Volume of solution × Density = 80 mL × 1.42 g/mL
= 113.6 g
Step 2: Calculate the mass of HNO3 in the solution.
Percentage concentration of HNO3 = 70%
Mass of HNO3 = Mass of solution × Percentage concentration
= 113.6 g × 70%
= 79.52 g
Step 3: Round the answer to the nearest whole number.
Rounding 79.52 g to the nearest whole number, we get 80 g.
Therefore: The grams of HNO3 in 80 mL of the 70% HNO3 solution is approximately 80 g.
To know more about mass in a chemical solution, visit:
https://brainly.com/question/32232951
#SPJ11
Which of the following linear hydrocarbons may have a double bond? A) C_6 H_14 B) C_10 H_20 C) C_5 H_8 D) C_12H_22
The linear hydrocarbon that may have a double bond is option C) C5H8.
To determine which of the given linear hydrocarbons may have a double bond, we need to consider the molecular formula and the number of hydrogen atoms in each molecule.
A) C6H14: This hydrocarbon has 6 carbon atoms and 14 hydrogen atoms. The general formula for an alkane (saturated hydrocarbon) with n carbon atoms is CnH2n+2. By applying this formula, we find that C6H14 corresponds to an alkane.
Since alkanes only have single bonds between carbon atoms, there is no double bond present. Therefore, option A is not the correct answer.
B) C10H20: This hydrocarbon has 10 carbon atoms and 20 hydrogen atoms. Again, applying the general formula for alkanes, we see that C10H20 corresponds to an alkane. Therefore, option B is not the correct answer.
C) C5H8: This hydrocarbon has 5 carbon atoms and 8 hydrogen atoms. The general formula for an alkene (unsaturated hydrocarbon with one double bond) with n carbon atoms is CnH2n. By comparing the molecular formula C5H8 to the formula for alkenes, we see that the ratio matches.
Therefore, option C is a possible linear hydrocarbon that may have a double bond.
D) C12H22: This hydrocarbon has 12 carbon atoms and 22 hydrogen atoms. Applying the general formula for alkanes, we see that C12H22 corresponds to an alkane. Therefore, option D is not the correct answer.
Based on the analysis, the linear hydrocarbon that may have a double bond is C) C5H8.
Learn more about hydrocarbon from the given link
https://brainly.com/question/7509853
#SPJ11
Calculate the number of grams of NaCN that must be added to 1.0 L of a 0.5M HCN solution to give a pH of 7.0. (Ka for HCN is 6.2 x 10-10)
A. 0.0034g
B. 11g
C. 24g
D. 160g
E. 0.15g
The number of grams of NaCN that must be added to the solution is approximately 1.52 x 10^(-8) g.
To calculate the number of grams of NaCN that must be added to 1.0 L of a 0.5M HCN solution to give a pH of 7.0, we need to consider the dissociation of HCN and the resulting concentration of CN- ions.
The dissociation of HCN can be represented by the equation: HCN ⇌ H+ + CN-
Since we want to achieve a pH of 7.0, we know that the concentration of H+ ions should be equal to 10^(-7) M. Using the equation for the dissociation constant (Ka) of HCN (6.2 x 10^(-10)), we can determine the concentration of CN- ions.
Ka = [H+][CN-]/[HCN]
By substituting the known values into the equation, we can solve for [CN-]. Rearranging the equation, we have:
[Cn-] = (Ka * [HCN])/[H+]
[Cn-] = (6.2 x 10^(-10) * 0.5) / 10^(-7)
[Cn-] = 3.1 x 10^(-10) M
Now, we can calculate the number of moles of CN- ions present in the 1.0 L solution:
moles = concentration * volume
moles = 3.1 x 10^(-10) * 1.0
moles = 3.1 x 10^(-10) mol
Finally, we can calculate the mass of NaCN required using the molar mass of NaCN (49.01 g/mol):
mass = moles * molar mass
mass = 3.1 x 10^(-10) * 49.01
mass ≈ 1.52 x 10^(-8) g
Therefore, the number of grams of NaCN that must be added to the solution is approximately 1.52 x 10^(-8) g.
Know more about dissociation here:
https://brainly.com/question/32501023
#SPJ11
If the BOD5 of a waste is 210 mg/L and BOD (Lo) is 363 mg/L. The BOD rate constant, k for this waste is nearly: 1) k = 0.188 2) k = 0.211 3) k = 0.218 4) k = 0.173
The correct option from the given choices is:
3) k = 0.218
The BOD rate constant, k, is a measure of the rate at which the biochemical oxygen demand (BOD) of a waste is consumed. It can be calculated using the BOD5 (BOD after 5 days) and BOD (Lo) (initial BOD) values.
To find the BOD rate constant, we can use the formula:
[tex]k = (ln(BOD (Lo) / BOD5)) / t[/tex]
Where:
- ln refers to the natural logarithm function
- BOD (Lo) is the initial BOD value (363 mg/L)
- BOD5 is the BOD after 5 days value (210 mg/L)
- t is the time in days (which is 5 days in this case)
Now, let's substitute the values into the formula:
k = (ln(363 / 210)) / 5
Calculating the natural logarithm of (363 / 210):
k = (ln(1.7286)) / 5
k ≈ 0.218
Therefore, the BOD rate constant, k, for this waste is approximately 0.218.
So, the correct option from the given choices is:
3) k = 0.218
the BOD rate constant (k) is a measure of the rate at which the biochemical oxygen demand (BOD) of a waste is consumed. In this case, the BOD5 of the waste is 210 mg/L and the initial BOD (BOD (Lo)) is 363 mg/L. To calculate the BOD rate constant, we use the formula k = (ln(BOD (Lo) / BOD5)) / t, where ln refers to the natural logarithm function, BOD (Lo) is the initial BOD value, BOD5 is the BOD after 5 days value, and t is the time in days. Substituting the given values into the formula, we find that k ≈ 0.218. Therefore, the correct option is 3) k = 0.218. The BOD rate constant gives us insight into how quickly the waste's BOD is being consumed, which is important in environmental and wastewater treatment applications.
Learn more about logarithm function from the link:
https://brainly.com/question/13473114
#SPJ11
What should be the quantity of chlorine required to treat a flow of 3MLD if the chlorine demand is 12mg/L and a chlorine residual of 2mg/L is desired?
The total amount of chlorine required per day would be 17,820 kg/day.
Therefore, the quantity of chlorine required to treat a flow of 3 MLD if the chlorine demand is 12mg/L and a chlorine residual of 2mg/L is desired is 30kg/day.
To treat a flow of 3 MLD, the quantity of chlorine required, given a chlorine demand of 12mg/L and a chlorine residual of 2mg/L is 30kg/day.Chlorination is a water treatment process that employs chlorine or chlorine-containing compounds to purify water. The most widely used disinfectant for drinking water, chlorine is relatively inexpensive and capable of killing most pathogens that might be present in the water.
How much chlorine is needed to treat water?
The amount of chlorine needed to treat water is determined by the amount of organic and inorganic matter, ammonia, nitrogen, and other substances present in the water that can react with the chlorine and the volume of water to be treated.
The quantity of chlorine that is required is usually measured in mg/L (milligrams per litre) or ppm (parts per million). For example, a chlorine demand of 12mg/L indicates that 12 milligrams of chlorine are required to disinfect 1 litre of water.
So, to calculate the quantity of chlorine needed to treat a flow of 3 MLD, we need to multiply the flow rate (3 MLD) by the chlorine demand (12mg/L) and then by the number of days in the year (365). This will give us the total amount of chlorine needed per year. Then, we divide this amount by 365 to get the amount of chlorine needed per day.Mathematically,Quantity of chlorine required
= Flow rate x Chlorine demand x 365 / 1000 kg/day
= 3 MLD x 12 mg/L x 365 / 1000 kg/day
= 13,140 kg/day
However, this only gives us the amount of chlorine needed to meet the chlorine demand. If we also want to achieve a chlorine residual of 2 mg/L, we need to add the amount of chlorine required to achieve this residual. The amount of chlorine required to achieve a residual can be determined by conducting a jar test or by using empirical data.For instance, let us say that based on empirical data, we need to add 4 mg/L of chlorine to achieve a residual of 2 mg/L. The total amount of chlorine required per day would be 17,820 kg/day.
Therefore, the quantity of chlorine required to treat a flow of 3 MLD if the chlorine demand is 12mg/L and a chlorine residual of 2mg/L is desired is 30kg/day.
To know more about chlorine visit:
https://brainly.com/question/19460448
#SPJ11
Consider the curve x=t+e^t,y=t−e^t. (a) Find all points (if any) on the curve where the tangent line is horizontal and where it is vertical. (b) Determine where the curve is concave upward and where it is concave downward.
The answer is: (a) The tangent line is horizontal at [tex]$(0,0)$[/tex]. There is no point where the tangent line is vertical.(b) The curve is concave upwards and downwards on the interval [tex]$(-\infty,0)$[/tex].
Consider the curve [tex]$x=t+e^t, y=t−e^t$.[/tex]
We are to find the following:
(a) Find all points (if any) on the curve where the tangent line is horizontal and where it is vertical.
(b) Determine where the curve is concave upward and where it is concave downward.
a) Horizontal tangent line occurs at points where
[tex]$\frac{dy}{dx} =0$.i.e. $\frac{dy}{dx} = \frac{d(t-e^t)}{d(t+e^t)}$ $= \frac{1-e^t}{1+e^t} = 0$.[/tex]
This occurs when [tex]$t=\ln(1) = 0$[/tex]
Thus $(0,0)$ is the only point where the tangent line is horizontal.
Vertical tangent line occurs at points where
[tex]$\frac{dx}{dy} =0$.i.e. $\frac{dx}{dy} = \frac{d(t+e^t)}{d(t-e^t)}$ $= \frac{1+e^t}{1-e^t} = 0$[/tex]
This occurs when [tex]$t=\ln(-1)$.[/tex]
But [tex]$\ln(-1)$[/tex] is undefined in the real number system.
So there is no point where the tangent line is vertical.
b) For the curve to be concave upwards,
[tex]$\frac{d^2y}{dx^2} = \frac{d}{dx}(\frac{dy}{dx}) > 0$.i.e. $\frac{d}{dx}(\frac{1-e^t}{1+e^t}) > 0$ $\frac{-2e^t}{(1+e^t)^2} > 0$ $-2e^t > 0$ $e^t < 0$[/tex]
This occurs when [tex]$t<0$[/tex]
For the curve to be concave downwards,
[tex]$\frac{d^2y}{dx^2} = \frac{d}{dx}(\frac{dy}{dx}) < 0$.i.e. $\frac{d}{dx}(\frac{1-e^t}{1+e^t}) < 0$ $\frac{2e^t}{(1+e^t)^2} < 0$ $2e^t < 0$ $e^t < 0$[/tex]
This also occurs when [tex]$t<0$[/tex]
Thus the curve is concave upwards and downwards on the interval [tex]$(-\infty,0)$[/tex]
Answer: (a) The tangent line is horizontal at [tex]$(0,0)$[/tex]. There is no point where the tangent line is vertical.
(b) The curve is concave upwards and downwards on the interval [tex]$(-\infty,0)$[/tex].
To know more about tangent line visit:
https://brainly.com/question/28994498
#SPJ11
Help please , 20 points
If the measure of angle A is 23 degrees, the approximate measure of angle B is 67°.
If CA = 6.5 and BD = 5, then AD = 4.15 units.
What is a supplementary angle?In Mathematics and Geometry, a supplementary angle simply refers to two (2) angles or arc whose sum is equal to 180 degrees.
Additionally, the sum of all of the angles on a straight line is always equal to 180 degrees. In this scenario, we can logically deduce that the sum of the given angles are supplementary angles:
m∠ACB + m∠A + m∠B = 180°
m∠B = 180° - (90 + 23)
m∠B = 67°
Since AB is a diameter (angle D is a right angle), we would apply Pythagorean's theorem to find AD as follows;
AB² = AD² + DB²
AD² = AB² - DB²
AD² = 6.5² - 5²
AD = √17.25
AD = 4.15 units.
Read more on supplementary angle here: brainly.com/question/13250148
#SPJ1
a) State the differences between normally consolidated and over consolidated clay. A soil in the field at some depth has been subjected to a certain maximum effective past pressure in its geologic history. This maximum effective past pressure may be equal to or less than the existing effective overburden pressure at the time of sampling. The reduction of effective pressure in the field may be caused by natural geologic processes or human processes.
b) Choose ONE (1) suitable foundation type with TWO (2) valid reasons to support. your judgement based on the situation stated. Teguh Jaya Holding is proposing to develop a 20-storey apartment in Cyberjaya, Selangor. This proposed area is underlaid with 15m depth of clayey silts of very high-water table.
The differences between clay that has been too consolidated and clay that has been usually consolidated are listed below.
What are they?
Normally consolidated clay
Over-consolidated clay
The rate of consolidation is rapid.
The rate of consolidation is slow.
Highest value of void ratio.
Lowest value of void ratio.
More compressible.
Less compressible.
Higher water content and swelling potential.
Lower water content and swelling potential.
Higher permeability.
Lower permeability.
The OCR is equal to 1.
The OCR is greater than 1.
b) A pile foundation would be the most suitable foundation type for the construction of a 20-storey apartment in Cyberjaya, Selangor, underlaid with 15m depth of clayey silts of a very high-water table.
The following are the reasons for this selection of a pile foundation:
Reason 1: Pile foundations are suitable for use in soft soil conditions such as clayey silts. Pile foundations are suitable for soil types with low bearing capacity and high settlement rate.
A pile foundation transfers the load of the structure to a stronger layer beneath the soil, preventing excessive settlement and maintaining stability.
Reason 2: Pile foundations may be installed to reach the required soil depth. Pile foundations are used to transfer load through poor soil to stronger strata beneath the soil.
They are installed by drilling or driving into the ground until they reach a layer of soil or rock with adequate strength.
Since the proposed area has a high-water table, pile foundations are also ideal for use in such conditions because they can be extended through water to the underlying stronger strata.
To know more on soil visit:
https://brainly.com/question/31227835
#SPJ11
Normally consolidated clay has experienced a maximum effective past pressure equal to or less than the existing overburden pressure, while over consolidated clay has experienced a greater past pressure. For an apartment in Cyberjaya with clayey silts and a high water table, a suitable foundation type would be pile foundations due to their ability to handle poor load-bearing capacity and resist the upward pressure from groundwater.
a) Normally consolidated clay and over consolidated clay are two types of clay soils with different characteristics.
Normally consolidated clay refers to clay that has experienced a maximum effective past pressure that is equal to or less than the existing effective overburden pressure at the time of sampling. This means that the clay has undergone natural or human-induced processes that have caused a reduction in effective pressure in the field. As a result, normally consolidated clay tends to have relatively predictable and consistent behavior under loading. When subjected to additional loading, the normally consolidated clay will continue to consolidate and settle gradually over time.
On the other hand, over consolidated clay refers to clay that has experienced a maximum effective past pressure that is greater than the existing effective overburden pressure at the time of sampling. This means that the clay has undergone natural or human-induced processes that have caused the clay to be subjected to higher pressures in the past. As a result, over consolidated clay tends to be more compact and dense compared to normally consolidated clay. It also exhibits higher strength and stiffness due to the previous higher pressures it has experienced.
b) Based on the given situation of developing a 20-storey apartment in Cyberjaya, Selangor, with a 15m depth of clayey silts of very high-water table, a suitable foundation type would be a pile foundation.
Two valid reasons to support this judgment are:
1. Load-bearing capacity: Pile foundations are commonly used in areas with weak or compressible soils, such as clayey silts. By driving piles deep into the ground, the foundation can transfer the load of the structure to a more stable layer of soil or rock below. In this case, the 15m depth of clayey silts suggests the need for a deep foundation to ensure adequate load-bearing capacity.
2. Water table considerations: The presence of a very high-water table indicates the potential for saturated soil conditions. Pile foundations can be designed to withstand the effects of groundwater and minimize settlement caused by water infiltration. By utilizing piles, the foundation can be elevated above the water table, reducing the risk of instability and potential damage to the structure.
Overall, a pile foundation would be a suitable choice for the proposed apartment building in Cyberjaya, Selangor, due to its ability to provide adequate load-bearing capacity and address the challenges posed by the high-water table and clayey silts.
Learn more about consolidated
https://brainly.com/question/28583417
#SPJ11
1-Name two factors that affect the resilience of wood joints. 2-Name two factors that affect the embedding strength of a timber member. 3-Explain the meaning of the coefficient kmod 4-What is the difference between homogeneous and combined glued laminated timber? With combined glued laminated timber, should the outer or inner lamellas have greater strength? Justify your answer. 5-Describe the relationship between the tensile strength and the angle between the force and grain direction in timber construction using a graph.
Resilience in wood joints depends on wood type, joint design, and embedding strength of timber members. The coefficient k mod adjusts design values based on moisture content. Homogeneous glued laminated timber has identical strength and stiffness layers, while combined glued laminated timber has different properties. Tensile strength decreases with increasing force and grain direction, as shown in a graph.
1. Two factors that affect the resilience of wood joints are: the type of wood used for the joint the joint design
2. Two factors that affect the embedding strength of a timber member are: the density and moisture content of the timber member the dimensions of the member and the size and number of fasteners used
3. The coefficient k mod is used to adjust the design value of a timber member based on its moisture content. It is the ratio of the strength of a wet timber member to that of a dry timber member.
4. Homogeneous glued laminated timber is made from layers of timber that are identical in strength and stiffness, whereas combined glued laminated timber is made from layers of timber with different properties. In combined glued laminated timber, the outer lamellas have greater strength because they are subject to higher stresses than the inner lamellas.
5. The tensile strength of timber decreases as the angle between the force and grain direction increases. This relationship can be represented by a graph that shows the tensile strength as a function of the angle between the force and grain direction. The graph is a curve that starts at a maximum value when the force is applied parallel to the grain direction, and decreases as the angle increases until it reaches a minimum value when the force is applied perpendicular to the grain direction.
To know more about Resilience Visit:
https://brainly.com/question/31947998
#SPJ11
HELP ME PLS IM BEGGING
Given c = 10.5, m∠A = 30, and m∠B = 52, we can use the Law of Sines to find b. Rounded to the nearest tenth, b ≈ 8.0.
Given b = 20, a = 26, and m∠A = 65, we can use the Law of Sines to find m∠B. Rounded to the nearest tenth, m∠B ≈ 47.5.
Given a = 125, m∠A = 42, and m∠B = 65, we can use the Law of Sines to find c. Rounded to the nearest tenth, c ≈ 154.3.
Given c = 18.4, m∠B = 35, and m∠C = 52, we can use the Law of Sines to find a. Rounded to the nearest tenth, a ≈ 10.5.
Given a = 12.5, m∠A = 50, and m∠B = 65, we can use the Law of Sines to find b. Rounded to the nearest tenth, b ≈ 15.2.
1)To find the length of side b, we can use the Law of Sines. The formula is:
b/sin(B) = c/sin(C)
Plugging in the given values:
b/sin(52) = 10.5/sin(180 - 30 - 52)
Using the sine addition formula:
b/sin(52) = 10.5/sin(98)
Cross-multiplying:
b * sin(98) = 10.5 * sin(52)
Dividing both sides by sin(98):
b = (10.5 * sin(52)) / sin(98)
Calculating the value:
b ≈ 7.96
Rounded to the nearest tenth:
b ≈ 8.0
2)To find the measure of angle B, we can use the Law of Sines. The formula is:
sin(B)/b = sin(A)/a
Plugging in the given values:
sin(B)/20 = sin(65)/26
Cross-multiplying:
sin(B) = (20 * sin(65)) / 26
Taking the inverse sine:
B ≈ [tex]sin^{(-1)[/tex]((20 * sin(65)) / 26)
Calculating the value:
B ≈ 47.5
Rounded to the nearest tenth:
B ≈ 47.5
3)To find the length of side c, we can use the Law of Sines. The formula is:
c/sin(C) = a/sin(A)
Plugging in the given values:
c/sin(65) = 125/sin(42)
Cross-multiplying:
c * sin(42) = 125 * sin(65)
Dividing both sides by sin(42):
c = (125 * sin(65)) / sin(42)
Calculating the value:
c ≈ 154.3
Rounded to the nearest tenth:
c ≈ 154.3
4)To find the length of side a, we can use the Law of Sines. The formula is:
a/sin(A) = c/sin(C)
Plugging in the given values:
a/sin(35) = 18.4/sin(52)
Cross-multiplying:
a * sin(52) = 18.4 * sin(35)
Dividing both sides by sin(52):
a = (18.4 * sin(35)) / sin(52)
Calculating the value:
a ≈ 10.5
Rounded to the nearest tenth:
a ≈ 10.5
5)To find the length of side b, we can use the Law of Sines. The formula is:
b/sin(B) = a/sin(A)
Plugging in the given values:
b/sin(65) = 12.5/sin(50)
Cross-multiplying:
b * sin(50) = 12.5 * sin(65)
Dividing both sides by sin(50):
b = (12.5 * sin(65)) / sin(50)
Calculating the value:
b ≈ 15.2
Rounded to the nearest tenth:
b ≈ 15.2
Know more about Law of Sines here:
https://brainly.com/question/30401249
#SPJ8
The complete question is :
Given the measures of AABC. answer the following question. Then round off answers to the nearest tenths.
1. If c = 10.5, m∠A = 30, m∠ B=52, find b.
2. If b=20, a = 26, m∠ A= 65, find m ∠ B.
3. If a = 125, m∠A=42, m ∠ B=65, find c.
4. If c= 18.4, m∠ B = 35, m ∠ C= 52, find a.
5. If a = 12.5, m∠A = 50, m∠ B = 65, find b
34% of f is equal to 85% of g.
What number should go in the box below?
g =
% of f
Answer:
g = 40% of f---------------------------
34% of f is equal to 0.34f and 85% of g is equal to 0.85g.
These two are same:
0.34f = 0.85gThen g is:
g = 0.34f/0.85g = 0.4fHence g = 40% of f.
A 10-kg mass is attached to a spring, stretching it 0.7 m from its natural length. The mass is started in motion from the equilibrium position with an initial velocity of 1 m/sec in the upward direction. Find the non negative arbitrary constant if the force due to air resistance is -90v N. The initial conditions are x(0) = 0 (the mass starts at the equilibrium position) and i(0) = -1 (the initial velocity is in the negative direction). Use 1 decimal palce.
The mass is set in motion from the equilibrium position with an initial velocity of 1 m/s in the upward direction. The force due to air resistance is given by -90v N. The initial conditions are [tex]x(0) = 0 and v(0) = -1[/tex].
Let's solve this problem:
Now, let's calculate the force exerted by the spring.
[tex]F = -kx₀F = kx₀ [as the mass is moving upward][/tex]
The force exerted by the spring is:
[tex]90v = kx₀ ---------------(1)[/tex]
The force acting on the mass is:
[tex]ma = F - kx[/tex]
[tex]-mg = -kx - 90v ---------------(2)[/tex]
Here, m = 10 kg. Putting the values in equation (2)
[tex]10(-1) = -k(0.7) - 90(1)10 = 0.7k + 90k = 125.71 N/m[/tex]
From equation (1),
[tex]90v = kx₀ = 125.71 × 0.7v = 1.239 m/s[/tex]
The non-negative arbitrary constant is 1.2.
To know more about arbitrary visit:
https://brainly.com/question/2500029
#SPJ11
Dry saturated steam at 14 bar is expanded in a turbine nozzle to 10 bar, expansion following the law pV" = constant, where the value of n is 1.135. Calculate: i. The dryness fraction of the steam at exit; ii. The enthalpy drop through the nozzle per kg of steam; iii. The velocity of discharge; iv. The area of nozzle exit in mm² per kg of steam discharged per second.
(i) Dryness fraction at the exit: Approximately 14.7%
(ii) Enthalpy drop through the nozzle per kg of steam: Approximately 147.4 kJ/kg
(iii) Velocity of discharge: Approximately 17.16 m/s
(iv) Area of nozzle exit per kg of steam discharged per second: Approximately 6700 mm²
Given that,
Initial pressure (P₁) = 14 bar
Final pressure (P₂) = 10 bar
Expansion law: pV" = constant, where n = 1.135
Dryness fraction at the inlet (x₁) = 1 (since it's dry saturated steam)
i) To find the dryness fraction at the nozzle exit,
Use the expansion process equation.
Since the initial pressure (P₁) is 14 bar and the final pressure (P₂) is 10 bar, Use the equation:
[tex]P_1/P_2 = (x_2/x_1)^n[/tex],
Where x₁ and x₂ are the dryness fractions at the inlet and the exit, respectively.
Plugging in the values, we have
[tex]14/10 = (x_2/1)^{1.135.[/tex]
Solving for x₂, the dryness fraction at the exit is approximately 1.47 or 14.7%%.
ii) The enthalpy drop through the nozzle can be calculated using the equation:
Δh = h₁ - h₂,
Where h₁ and h₂ are the specific enthalpies at the inlet and the exit, respectively.
To find h₁, Use the saturated steam table at 14 bar to get the specific enthalpy, which is approximately 2812.9 kJ/kg.
For h², Use the saturated steam table at 10 bar to get the specific enthalpy, which is approximately 2665.5 kJ/kg.
Therefore, the enthalpy drop is approximately,
2812.9 - 2665.5 = 147.4 kJ/kg.
iii) To calculate the velocity of discharge,
Use the equation,
[tex]v_2 = (2(h_1-h_2))^{0.5}[/tex]
where v₂ is the velocity at the exit.
Plugging in the values, we have
[tex]v_2 \approx (2(2812.9-2665.5))^{0.5}[/tex]
≈ 17.16 m/s.
iv) To find the area of the nozzle exit,
Use the equation [tex]A = m_0 / ( \rho _2 v_2)[/tex],
where A is the area,
[tex]m_0[/tex] is the mass flow rate per second,
ρ₂ is the density at the exit, and
v₂ is the velocity at the exit.
Since we are considering 1 kg of steam discharged per second, the mass flow rate is 1 kg/s.
The density at the exit can be found using the saturated steam table at 10 bar, which is approximately 4.913 kg/m³.
Plugging in the values, we have
A ≈ 1 / (4.913 x 30.43)
≈ 0.0067 m² or 6700 mm².
Hence the required area is 6700 mm².
To learn more about Enthalpy visit:
https://brainly.com/question/32882904
#SPJ4
Solve the exponential equation using the method of relating the bases by first rewriting the equation in the form e^u=e^v. ex^2=(e^−x)⋅e^20
X=
(Simplify your answer.)
The solutions to the exponential equation are x = -5 and x = 4.
To solve the exponential equation using the method of relating the bases, we can rewrite the equation in the form
[tex]e^u = e^v,[/tex] where u and v are expressions involving x.
Given equation: [tex]ex^2 = (e^−x)⋅e^20[/tex]
First, let's rewrite the right side of the equation using the properties of exponents:
[tex]ex^2 = e^(20 - x)[/tex]
Now we can relate the bases by setting the exponents equal to each other:
[tex]x^2 = 20 - x[/tex]
To simplify further, let's bring all the terms to one side of the equation:
[tex]x^2 + x - 20 = 0[/tex]
This is now a quadratic equation. We can solve it by factoring or using the quadratic formula. Let's factor it:
(x + 5)(x - 4) = 0
Setting each factor equal to zero gives us two possible solutions:
x + 5 = 0 or x - 4 = 0
Solving each equation:
x = -5 or x = 4
Learn more about exponential equation:
https://brainly.com/question/11832081
#SPJ11
One variable that is measured by online homework systems is the amount of time a student spends on homework for each section of the text. The following is a summary of the number of minutes a student spends for each section of the text for the fall 2018 semester in a college algebra class at joliet junior college.
Q1 = 42 Q2 = 51. 5 Q3 = 72
a) provide an interpretation of these results.
b) determind and interpret the interquartile range
c) suppose a student spent 2 hours doing homework for a section. Is this an outlier?
d) do you believe that the distribution of time spent doing homework is skewed or symmetric? Why?
a) The results provided are the quartiles of the amount of time students spent on homework for each section of the college algebra class. The quartiles divide the data into four equal parts.
Q1 represents the first quartile, which indicates that 25% of the students spent 42 minutes or less on homework for each section. This implies that a quarter of the students completed their homework relatively quickly.
Q2 represents the second quartile, also known as the median. In this case, it is 51.5 minutes. This means that 50% of the students spent 51.5 minutes or less on homework, indicating the middle value of the distribution.
Q3 represents the third quartile, indicating that 75% of the students spent 72 minutes or less on homework for each section. This implies that the majority of the students completed their homework within this time frame.
b) The interquartile range (IQR) can be calculated by subtracting the first quartile (Q1) from the third quartile (Q3). In this case, the IQR is Q3 - Q1 = 72 - 42 = 30 minutes.
Interpreting the IQR, it represents the range within which the middle 50% of the data lies. In other words, it quantifies the spread of the data around the median. Here, the IQR suggests that the majority of students spent between 42 minutes and 72 minutes on homework for each section.
c) If a student spent 2 hours (120 minutes) doing homework for a section, it would be considered an outlier since it falls outside the range of Q1 - 1.5 * IQR to Q3 + 1.5 * IQR. In this case, Q1 - 1.5 * IQR = 42 - 1.5 * 30 = -3, and Q3 + 1.5 * IQR = 72 + 1.5 * 30 = 117. Therefore, 120 minutes is greater than the upper limit of 117 minutes, indicating that it is an outlier.
d) Based on the provided information, it is difficult to determine whether the distribution of time spent doing homework is skewed or symmetric. Additional information, such as a histogram or the mean and standard deviation, would be required to make a more accurate assessment.
Learn more about algebra here
https://brainly.com/question/4344214
#SPJ11
Find the eigenvalues λn and eigenfunctions yn(x) for the equation y′′+λy=0 in each of the following cases: (a) y(0)=0,y(π/2)=0; (b) y(0)=0,y(2π)=0; (c) y(0)=0,y(1)=0; (d) y(0)=0,y(L)=0 when L>0; (e) y(−L)=0,y(L)=0 when L>0; (f) y(a)=0,y(b)=0 when a
we have y[tex]n= n2π24L2n = 1,3,5,...[/tex]0.
his gives us the following solutions: λ[tex]n= n2π24L2n = 1,3,5,...[/tex]
yn([tex]x) = sin(nπxL), n = 1,3,5,...(f) y(a)=0,y(b)=0[/tex]
For the boundary conditions, we have y(0)=0 and y(π/2)=0. This gives us the following solutions:
λn= n2π2n = 1,2,3,... yn(x)
= sin(nπx2), n = 1,2,3,...(b)
y(0)=0,y(2π)=0
For the boundary conditions, we have y(0)=0 and y(2π)=0.
This gives us the following solutions:λn= n2π2n = 1,2,3,... y[tex]n(x) = sin(nπxπ), n = 1,2,3,...(c) y(0)=0,y(1)=0[/tex]
For the boundary conditions, we have y(0)=0 and y(1)=0.
This gives us the following solutions:λn= n2π2n = 1,2,3,...
yn(x) = sin(nπx), n = 1,3,5,... and
yn(x) = cos(nπx) − cos(nπ),
n = 2,4,6,...(d)
y(0)=0,y(L)=0 when L>0
For the boundary conditions, we have [tex]y(0)=0 and y(L)=0[/tex].
To know more about gives visit:
https://brainly.com/question/29424969
#SPJ11
What is the maximum tractive effort that can be developed for this rear-wheel drive car: • Weight: 2,750 lb. Wheelbase: 113 inches. Center of gravity: 23.5 inch above the road and 51 inch behind the front axle Use maximum coefficient of adhesion on poor, wet pavement.
The maximum tractive effort that can be developed for this rear-wheel drive car is 4719.98 lbf (pound force). Tractive effort is the force applied to the wheels of a vehicle to make them move. It is a measure of how much force is needed to move the vehicle.
The formula for tractive effort is given by:T = W × f where T is the tractive effort, W is the weight of the vehicle, and f is the coefficient of adhesion. For a rear-wheel-drive car, the tractive effort is given by:T = (W × g × µr) / rwhere g is the acceleration due to gravity (32.2 ft/s²), µr is the coefficient of rolling resistance, and r is the effective radius of the drive wheel.The coefficient of adhesion on poor, wet pavement is 0.1. The weight of the car is 2,750 lb. The center of gravity is 23.5 inches above the road and 51 inches behind the front axle.
The wheelbase is 113 inches. The effective radius of the drive wheel is given by:r = sqrt((w² / 4) + h²)where w is the wheelbase (113 inches) and h is the height of the center of gravity above the rear axle (23.5 - 51 = -27.5 inches, since it is behind the front axle).Therefore,r = sqrt((113² / 4) + (-27.5)²)
≈ 61.2 inches
The tractive effort is given by:T = (W × g × µr) / r
T = (2750 × 32.2 × 0.1) / 61.2T
≈ 4719.98 lbf
Therefore, the maximum tractive effort that can be developed for this rear-wheel drive car is 4719.98 lbf.
To know more about tractive effort visit:
https://brainly.com/question/30163187
#SPJ11
Solve for mzA. Enter your answer in the box. Round your final answer to the nearest degree.
The measure of angle A to the nearest degree is 50°
What is trigonometric ratio?The trigonometric functions are real functions which relate an angle of a right-angled triangle to ratios of two side lengths.
sinθ = opp/hyp
cosθ = adj/ hyp
tanθ = opp/adj
Taking reference form angle A,
10cm = AC = adjacent
12cm = BC = opposite
Therefore we are going to use the tan function.
Tan A = 12/10
Tan A = 1.2
A = 50° ( to the nearest degree)
Therefore the measure of A to the nearest degree is 50°
learn more about trigonometric ratio from
https://brainly.com/question/24349828
#SPJ1
There are 6 white kittens, 1 orange kitten, and 1 striped kitten at the pet shop. If you were to pick one kitten without looking, what is the probability that it would be white? Select one: a. 1/6 b. Not Here c. 3/4 d. 1/4 e. 1/8
The total number of kittens at the pet shop is 6 + 1 + 1 = 8.The number of white kittens at the pet shop is 6.The probability of picking a white kitten is 6/8, which simplifies to 3/4.The correct answer is c. 3/4.
Therefore, the probability of picking a white kitten without looking is 6/8 or 3/4.
The probability of picking a white kitten out of 8 kittens (which includes 6 white kittens) is 3/4.
This is because the total number of kittens at the pet shop is 8, and the number of white kittens is 6.
The formula for probability is P = number of desired outcomes/number of possible outcomes.
Here, the desired outcome is picking a white kitten, and the possible outcomes are all 8 kittens at the pet shop.
Since there are 6 white kittens and 8 total kittens, the probability of picking a white kitten is 6/8, which simplifies to 3/4.The correct answer is c. 3/4.
To know more about probability visit:
https://brainly.com/question/31828911
#SPJ11
Problem 3 (16 points). Consider the following phase plot for an autonomous ODE: a) Find the equilibrium solutions of the equation. b) Draw the Phase Line for this equation. c) Classify the equilibria as asymptotically stable, semi-stable, or unstable. d) Sketch several solutions for this ODE; make sure the concavity of the solutions is correct.
The equilibrium solutions of the given equation are x = -1 and x = 1. The phase line for the given equation is stable at x = -1 and unstable at x = 1. The equilibrium point at x = -1 is asymptotically stable, and the equilibrium point at x = 1 is unstable.
Equilibrium solutions are defined as the solution of the differential equation where the rate of change is zero. From the given phase plot, we can see that there are two equilibrium points. One is at x = -1 and the other is at x = 1. Therefore, the equilibrium solutions of the given equation are x = -1 and x = 1.
A phase line is a horizontal line that represents all possible equilibrium solutions for the given differential equation. The phase line is drawn with a dashed line to represent unstable equilibrium and a solid line to represent stable equilibrium. The phase line for the given equation is as follows:We can see that there is a stable equilibrium at x = -1 and an unstable equilibrium at x = 1.
To classify the equilibria as asymptotically stable, semi-stable, or unstable, we need to analyze the stability of the equilibrium points. As the equilibrium point at x = -1 is a stable equilibrium, it is asymptotically stable. As the equilibrium point at x = 1 is an unstable equilibrium, it is unstable.
From the given phase plot, we can see that the concavity of the solutions for x < -1 and -1 < x < 1 is downward, and for x > 1 is upward.
In this problem, we found the equilibrium solutions of the equation, drew the phase line for the equation, classified the equilibria as asymptotically stable, semi-stable, or unstable, and sketched several solutions for this ODE. The equilibrium solutions of the given equation are x = -1 and x = 1. The phase line for the given equation is stable at x = -1 and unstable at x = 1.
The equilibrium point at x = -1 is asymptotically stable, and the equilibrium point at x = 1 is unstable. The sketch of the solution for the given ODE is shown above.
To know more about differential equation visit:
brainly.com/question/33433874
#SPJ11
The type of transport that allows amino acids to move across cell membranes with the use of a protein channel without using chemical energy is called: A) facilitated transport. B) diffusion.
C) active transport. D) train transport E) air transport A- B - C -
D -
E-
The correct answer is A) facilitated transport. Facilitated transport, also known as facilitated diffusion, is the type of transport that allows amino acids to move across cell membranes with the use of protein channels.
In facilitated transport, specific protein channels or carriers embedded in the cell membrane aid in the movement of molecules or ions across the membrane.
In the case of amino acids, these molecules are polar and cannot easily pass through the nonpolar lipid bilayer of the cell membrane. Therefore, protein channels provide a pathway for amino acids to cross the membrane. These protein channels are selective and allow only specific molecules, such as amino acids, to pass through.
Facilitated transport does not require the expenditure of chemical energy, such as ATP. Instead, it relies on the concentration gradient of the molecules being transported. The movement occurs from an area of higher concentration to an area of lower concentration, following the concentration gradient.
The protein channels used in facilitated transport exhibit specificity and selectivity for certain molecules, including amino acids. These channels have binding sites that recognize and bind to specific amino acids, facilitating their transport across the membrane.
Therefore, the correct answer is A) facilitated transport, which describes the transport of amino acids across cell membranes with the use of protein channels.
Learn more about amino acids:
https://brainly.com/question/14351754
#SPJ11
6-10 Let m, n E Z. Prove by contraposition: If m+ n ≥ 19, then m≥ 10 or n ≥ 10.
By contraposition, we have proven that if m + n ≥ 19, then m ≥ 10 or n ≥ 10.
To prove the statement "If m + n ≥ 19, then m ≥ 10 or n ≥ 10" by contraposition, we assume the negation of the conclusion and show that it implies the negation of the original statement. The negation of the conclusion "m ≥ 10 or n ≥ 10" is "m < 10 and n < 10." The negation of the original statement "If m + n ≥ 19, then m ≥ 10 or n ≥ 10" is "It is not the case that if m + n ≥ 19, then m ≥ 10 or n ≥ 10."
Let's proceed with the proof:
Assume m < 10 and n < 10. We want to show that if m + n ≥ 19, then m ≥ 10 or n ≥ 10 is false.
Since m < 10, we know that the maximum value m can take is 9. Similarly, since n < 10, the maximum value n can take is 9 as well.
If both m and n are at their maximum value of 9, the sum m + n would be 9 + 9 = 18, which is less than 19. Therefore, if m and n are both less than 10, their sum can never be greater than or equal to 19.
Hence, the negation of the conclusion "m < 10 and n < 10" implies the negation of the original statement "If m + n ≥ 19, then m ≥ 10 or n ≥ 10."
Therefore, by contraposition, we have proven that if m + n ≥ 19, then m ≥ 10 or n ≥ 10.
To know more value click-
http://brainly.com/question/843074
#SPJ11
"
What is the coefficient of x²wa³b in the expansion of (x+y+w+a+b)^7?
The coefficient of x²wa³b in the expansion of (x+y+w+a+b)⁷ is 420.
To find the coefficient of x²wa³b in the expansion of (x+y+w+a+b)^7, we can use the multinomial theorem.
According to the multinomial theorem, the coefficient of a term in the expansion of (x+y+w+a+b)ⁿ is given by:
Coefficient = n! / (r₁! * r₂! * r₃! * r₄! * r₅!)
Where n is the power to which the binomial is raised (in this case, 7), and r₁, r₂, r₃, r₄, and r₅ are the exponents of x, y, w, a, and b, respectively, in the term we are interested in.
In this case, we want to find the coefficient of the term with x²wa³b.
The exponents of x, y, w, a, and b in this term are 2, 0, 1, 3, and 1, respectively.
Plugging these values into the formula, we have:
Coefficient = 7! / (2! * 0! * 1! * 3! * 1!)
= 5040 / (2 * 1 * 6 * 1)
= 5040 / 12
= 420
Therefore, the coefficient of x²wa³b in the expansion of (x+y+w+a+b)⁷ is 420.
To know more about coefficient, click
https://brainly.com/question/1594145
#SPJ11
The coefficient of [tex]\(x^2wa^3b\)[/tex] in the expansion of [tex]\((x+y+w+a+b)^7\)[/tex] is the numerical value that multiplies the term [tex]\(x^2wa^3b\)[/tex] when the expression is fully expanded. In this case, we need to find the coefficient of this specific term in the binomial expansion.
To calculate the coefficient, we can use the Binomial Theorem. According to the Binomial Theorem, the coefficient of a term in the expansion of [tex]\((x+y+w+a+b)^n\)[/tex] can be found by using the formula:
[tex]\[\binom{n}{r_1, r_2, r_3, r_4, r_5} \cdot x^{r_1} \cdot y^{r_2} \cdot w^{r_3} \cdot a^{r_4} \cdot b^{r_5}\][/tex]
Where [tex]\(\binom{n}{r_1, r_2, r_3, r_4, r_5}\)[/tex] represents the binomial coefficient, which is the number of ways to choose the exponents [tex]\(r_1, r_2, r_3, r_4, r_5\)[/tex] from the powers of [tex]\(x, y, w, a, b\)[/tex] respectively, and n is the exponent of the binomial.
In this case, we want to find the coefficient of [tex]\(x^2wa^3b\)[/tex] in the expansion of [tex]\((x+y+w+a+b)^7\)[/tex]. We can determine the exponents [tex]\(r_1, r_2, r_3, r_4, r_5\)[/tex] that correspond to this term and calculate the binomial coefficient using the formula above.
To learn more about coefficient refer:
https://brainly.com/question/24068089
#SPJ11
The power of a red laser (A = 630 nm) is 2.75 watts (abbreviated W, where 1 W = 1 J/s). How many photons per second does the laser emit?
The red laser emits approximately 8.73 x 10^18 photons per second
To calculate the number of photons emitted per second by the red laser, we can use the formula:
Number of photons per second = Power of the laser (W) / Energy of one photon (J)
The energy of one photon can be calculated using the formula:
Energy of one photon (J) = Planck's constant (h) * Speed of light (c) / Wavelength (λ)
First, let's calculate the energy of one photon:
Wavelength (λ) = 630 nm = 630 x 10^(-9) m (convert nanometers to meters)
Planck's constant (h) = 6.626 x 10^(-34) J·s
Speed of light (c) = 3.00 x 10^8 m/s
Energy of one photon (J) = (6.626 x 10^(-34) J·s * 3.00 x 10^8 m/s) / (630 x 10^(-9) m)
Energy of one photon ≈ 3.15 x 10^(-19) J
Now, let's calculate the number of photons emitted per second:
Power of the laser (W) = 2.75 W
Number of photons per second = 2.75 W / (3.15 x 10^(-19) J)
Number of photons per second ≈ 8.73 x 10^18 photons/s
So, the red laser emits approximately 8.73 x 10^18 photons per second.
Learn more about photons:brainly.com/question/9359397
#SPJ11
If g(x)=(x−5)^3 (2x−7m)^4 and x=5 is a root with multiplicity n, what is the value of n?
If [tex]\displaystyle g( x) =( x-5)^{3}( 2x-7m)^{4}[/tex] and [tex]\displaystyle x=5[/tex] is a root with multiplicity [tex]\displaystyle n[/tex], we can determine the value of [tex]\displaystyle n[/tex] by evaluating [tex]\displaystyle g( x) [/tex] at [tex]\displaystyle x=5[/tex].
Substituting [tex]\displaystyle x=5[/tex] into [tex]\displaystyle g( x) [/tex], we have:
[tex]\displaystyle g( 5) =( 5-5)^{3}( 2( 5)-7m)^{4}[/tex]
Simplifying this expression, we get:
[tex]\displaystyle g( 5) =( 0)^{3}( 10-7m)^{4}[/tex]
[tex]\displaystyle g( 5) =0\cdot ( 10-7m)^{4}[/tex]
[tex]\displaystyle g( 5) =0[/tex]
Since [tex]\displaystyle g( 5) =0[/tex], it means that [tex]\displaystyle x=5[/tex] is a root of [tex]\displaystyle g( x) [/tex]. However, we need to determine the multiplicity of this root, which refers to the number of times it appears.
In this case, the root [tex]\displaystyle x=5[/tex] has a multiplicity of [tex]\displaystyle n[/tex]. Since the function [tex]\displaystyle g( x) [/tex] evaluates to [tex]\displaystyle 0[/tex] at [tex]\displaystyle x=5[/tex], it implies that the root [tex]\displaystyle x=5[/tex] appears [tex]\displaystyle n[/tex] times in the factored form of [tex]\displaystyle g( x) [/tex].
Therefore, the value of [tex]\displaystyle n[/tex] is [tex]\displaystyle 3[/tex] (the multiplicity of the root [tex]\displaystyle x=5[/tex]).
[tex]\huge{\mathfrak{\colorbox{black}{\textcolor{lime}{I\:hope\:this\:helps\:!\:\:}}}}[/tex]
♥️ [tex]\large{\underline{\textcolor{red}{\mathcal{SUMIT\:\:ROY\:\:(:\:\:}}}}[/tex]
Find the volume and surface area of the figure.
Round to the nearest hundredths when
necessary.
Answer:
Volume: 395.84 Surface Area: 929.86
Step-by-step explanation:
Volume: pie*radius*hieght
pie*(14/2)*18
pie*7*18
pie*126
395.84
Surface Area: 2πrh+2πr2
2*pie*7*18+2*pie*7*2
791.6813+87.96459
929.8558
Find measure angle of x
Answer:
Angle X = 67.38
Step-by-step explanation:
Cosine Law for Angles (SSS)
cosA = (b^2 + c^2 - a^2) / 2bc
Substitute that into the equation
cosA = (5^2 + 13^2 - 12^2) / 2(5)(13)
A = cos-1 [(5^2 + 13^2 - 12^2) / 2(5)(13)]
A = 67.38°
If the lengths AB=4cm, BC=5cm, and CD=9cm, calculate the length AC. Write your answer to 3 significant figures.
To find the length AC, use the Pythagorean Theorem, which states that for a right triangle, the sum of the squares of the legs (the shorter sides) equals the square of the hypotenuse (the longest side). So, the length of AC is 6.40 cm
The legs are AB and BC, while the hypotenuse is AC. Therefore, you can use the Pythagorean Theorem to calculate the length of AC. Then, add CD to the length of AC to obtain the length of AD. To summarize, we have the following steps:
Step 1: Use the Pythagorean Theorem to calculate the length of AC²AB² + BC² = AC²4² + 5² = AC²16 + 25 = AC²41AC² = 41AC = √41 = 6.403124237 (rounded to 3 significant figures)
Step 2: Add CD to the length of AC to find the length of ADAD = AC + CDAD = 6.403124237 + 9 = 15.40312424 (rounded to 3 significant figures). Therefore, the length of AC is 6.40 cm (rounded to 3 significant figures).
For more questions on: Pythagorean Theorem
https://brainly.com/question/343682
#SPJ8
Consider the following reaction where Kc=0.0120 at 500K. PCl5 (g)⇌PCl3(g)+Cl2(g) A reaction mixture was found to contain 0.106 moles of PCl5(g),0.0403 moles of PCl3(g), and 0.0382 moles of Cl2(g), in a 1.00 liter container. Calculate Qc. Qc= Is the reaction at equilibrium? If not, what direction must it run in order to reach equilibrium? a) The reaction must run in the forward direction to reach equilibrium. b) The reaction must run in the reverse direction to reach equilibrium. c) The reaction is at equilibrium.
a). The reaction must run in the forward direction to reach equilibrium. is the correct option. If Qc is less than Kc, the reaction will shift in the forward direction to reach equilibrium.
Given reaction is : PCl5 (g) ⇌ PCl3(g) + Cl2(g)We need to calculate Qc, which is the reaction quotient.
Qc is calculated in the same way as Kc, except that the concentrations used are not necessarily those when the system is at equilibrium. In general, if Qc=Kc, the system is at equilibrium.
Qc is calculated as follows: Q_c = \frac{[PCl_3][Cl_2]}{[PCl_5]}
Given, at 500K, Kc=0.0120, [PCl5]= 0.106 mol, [PCl3] = 0.0403 mol, [Cl2] = 0.0382 mol, in a 1.00 L container.
Q_c = \frac{[PCl_3][Cl_2]}{[PCl_5]} = \frac{(0.0403)(0.0382)}{(0.106)} Q_c = 0.0144
Since Qc is not equal to Kc, it is not at equilibrium. If Qc is greater than Kc, the reaction will shift in the reverse direction to reach equilibrium.
If Qc is less than Kc, the reaction will shift in the forward direction to reach equilibrium.
Therefore, the reaction must run in the forward direction to reach equilibrium.
To know more about equilibrium visit:
brainly.com/question/16857279
#SPJ11
7.00 moles of N2 molecule contains how many N atoms?
a) 8.44 X 10_26 atom
b)4.00 X 10_24 atom
c) 8.44 X 10_24 atom d) 2.44 X 10_24 atom
One mole of nitrogen gas (N2) contains 2 moles of nitrogen atoms. Therefore, if we have 7 moles of N2 molecules, we have 7 x 2 = 14 moles of nitrogen atoms.
Since one mole of any element contains 6.022 x 10^23 atoms, 14 moles will contain:
14 x 6.022 x 10^23=8.44 x 10^24N atoms.
Therefore, the appropriate is option C) 8.44 x 10^24 atom.
For this question, we use the mole concept of Avogadro's number. One mole of any substance contains 6.022 x 10^23 atoms, molecules or particles. Hence, if we want to find the number of atoms of nitrogen in 7 moles of nitrogen gas, we must first calculate the number of moles of nitrogen atoms present in it.
To find the number of moles of nitrogen atoms present in 7 moles of N2 molecules, we will use the stoichiometric coefficient.
The stoichiometric coefficient of nitrogen in N2 is 2. Therefore, one mole of nitrogen gas contains 2 moles of nitrogen atoms. As such, we can determine that 7 moles of N2 molecules contain 7 x 2 = 14 moles of nitrogen atoms.
Now that we know the number of moles of nitrogen atoms present, we can calculate the number of atoms present in 14 moles of nitrogen atoms.
By using Avogadro's number, we know that 1 mole of nitrogen atoms contains 6.022 x 10^23 atoms of nitrogen.
Therefore, 14 moles of nitrogen atoms will contain:
[tex]14 x 6.022 x 10^23 = 8.44 x 10^24 N atoms.[/tex]
So option C) [tex]8.44 x 10^24 atom.[/tex]
Thus, 7.00 moles of N2 molecule contains 8.44 X 10^24 N atoms.
To know more about stoichiometric coefficient :
brainly.com/question/32088573
#SPJ11
......Accrediting academic qualifications is one of the functions of 10 A)MQA B) IEM C) BEM D) IPTA
The correct option for accrediting academic qualifications is A) MQA.
function of accrediting academic qualifications is primarily carried out by the Malaysian Qualifications Agency (MQA), which is option A. MQA is responsible for ensuring the quality and standards of higher education in Malaysia. As an external quality assurance agency, MQA evaluates and accredits programs and institutions to ensure that they meet the required criteria and standards.
The Institution of Engineers Malaysia (IEM), option B, is a professional body that represents engineers in Malaysia. While IEM plays a crucial role in the engineering profession, including setting professional standards and promoting continuous professional development, it does not have the authority to accredit academic qualifications.
Similarly, the Board of Engineers Malaysia (BEM), option C, is responsible for regulating the engineering profession in Malaysia. BEM ensures that engineers meet the necessary qualifications and competencies to practice engineering. However, accrediting academic qualifications is not within its purview.
IPTA, option D, stands for Institut Pengajian Tinggi Awam or public universities in Malaysia. While these institutions play a significant role in offering academic programs and conferring degrees, the actual accreditation of qualifications is carried out by MQA.
In conclusion, the correct option for accrediting academic qualifications is A) MQA.
Learn more about academic qualifications
https://brainly.com/question/919597
#SPJ11