consider the following circuit what is the low pass cutoff frequency? group of answer choices 6.28 khz 15.9 khz 100 khz 628 khz

Technician A is correct that the adjusting nut should be rotated clockwise to decrease free travel when adjusting a manual slack adjuster on an S-cam foundation brake. Technician B is not correct in this case.

When adjusting a manual slack adjuster on an S-cam foundation brake, the lock collar should be retracted and the adjusting nut should always be rotated clockwise to decrease free travel.

The S-cam foundation brake is a type of drum brake commonly used in heavy-duty vehicles. It uses an S-shaped camshaft to force the brake shoes against the brake drum, resulting in friction and slowing down the vehicle. The slack adjuster is a critical component of the S-cam brake system that helps to maintain proper clearance between the brake shoes and the drum, known as "slack" or "free travel".

When adjusting the slack adjuster, rotating the adjusting nut clockwise will move the S-cam in the direction that reduces the slack or free travel, thus bringing the brake shoes closer to the brake drum. This will result in improved braking performance. On the other hand, rotating the adjusting nut counterclockwise will increase the slack or free travel, which is not desirable as it may result in reduced braking efficiency and longer stopping distances.

learn more about counterclockwise

brainly.com/question/16057909

#SPJ4

Demonstrating your ability to pay back borrowed money is one way to

develop a good credit history.

Paying bills on time and in full is another way to demonstrate that you can pay back money. Additionally, having a stable income, low debt-to-income ratio, and a low utilization of credit lines can all help demonstrate an ability to pay back borrowed money.

A good credit score is generally considered to be any score above 700. This score is typically determined by a credit reporting agency, such as Equifax, Experian, or TransUnion. Credit scores are calculated using a variety of factors, including the length and type of credit accounts, payment history, credit utilization, and more.

A score of 700 or higher is generally considered to be good because it indicates that a person is a relatively low risk for lenders and creditors. A good credit score can result in lower interest rates on loans and credit cards, as well as improved chances of approval for financing applications. Additionally, a good credit score may also be beneficial when applying for jobs, renting an apartment, or opening a new bank account.

Learn more about credit score here:

https://brainly.com/question/2609368

#SPJ1

To complete this task, you can use the following Python code:

```python
# Prompt the user to input an integer between 32 and 126
integer_input = int(input("Enter an integer between 32 and 126: "))

# Ensure the integer is within the specified range
while integer_input < 32 or integer_input > 126:
   integer_input = int(input("Enter an integer between 32 and 126: "))

# Prompt the user to input a float
float_input = float(input("Enter a float: "))

# Prompt the user to input a character
char_input = input("Enter a character: ")

# Ensure the input is a single character
while len(char_input) != 1:
   char_input = input("Enter a character: ")

# Prompt the user to input a string
string_input = input("Enter a string: ")

# Output the four values on a single line separated by a space
print(integer_input, float_input, char_input, string_input)
```

This code will prompt the user for the required inputs and ensure they are valid. It will then output the four values separated by a space as specified in the student question.

for more such question on python

https://brainly.com/question/28675211

#SPJ11

The total volume of Cubic Yards of Concrete is 4/27 Cubic Yards

Given that

Dimensions = 2 ft by 1 ft by 2 ft

The volume is the product of the dimensions

So, we have

Volume = 2 * 1  2

Evaluate

Volume = 4

Convert to cubic yards

Volume = 4/27

Hece, the volume is 4/27

Read more about volume  at

https://brainly.com/question/463363

#SPJ1

The new discharge may remain roughly the same or could even increase slightly, depending on the exact values of width, depth, and velocity.

The discharge of a river is the volume of water that passes through a given cross-section of the river per unit of time. It is calculated as the product of the cross-sectional area of the river channel (width times depth) and the flow velocity.

Discharge (Q) = Width (W) × Depth (D) × Velocity (V)

Given the following changes:

Channel depth (D) decreased to 1 ft

Width (W) stayed at 10 ft

Flow velocity (V) increased to 9 ft/sec

The new discharge (Q') can be calculated as:

Q' = W × D' × V'

Where D' is the new channel depth of 1 ft, and V' is the new flow velocity of 9 ft/sec.

An incompressible fluid, like the water in a river, has a constant mass flow rate along a streamline according to the fluid mechanics principle of continuity. This means that, in the absence of external forces, the product of the cross-sectional area and the flow velocity is constant. Here, we make the assumption that the river is in a stable state and that no outside factors are changing its flow.

When the channel depth (D) decreases to 1 ft, but the width (W) stays the same at 10 ft, the cross-sectional area (W × D') of the river decreases. However, the flow velocity (V') increases to 9 ft/sec.

As a result, if the continuity principle is valid, the decline in channel depth is balanced by the rise in flow velocity. This indicates that depending on the precise values of breadth, depth, and velocity, the new discharge (Q') may either stay nearly the same or perhaps significantly rise.

Learn more about velocity here:

brainly.com/question/29315574

#SPJ4

The entropy change of the R134a during this process is 0.035 KJ

Entropy change refers to the measure of the degree of disorder or randomness in a thermodynamic system. It is a concept in thermodynamics that describes the amount of energy that is unavailable for doing work in a given process.

The entropy change of a system can be calculated by subtracting the initial entropy of the system from its final entropy.

T = PV/(mR)

T1 = 180 / 10 * 0.08314

T2 = P2V/(mR)

Now T1 = T2

such that

0.08314 ln (100kpa / 180)

= 0.035 KJ

The entropy change of the R134a during this process is 0.035 KJ

Read more on entropy change herehttps://brainly.com/question/6364271

#SPJ1

The average cycle time is 94.85 seconds. The time required to complete the batch is 227,640 seconds, or approximately 63.23 hours

(a) Average Cycle Time:

The cycle time can be calculated as the sum of the setup time, processing time per cycle, and part handling time per cycle, divided by the number of parts produced per cycle.

Cycle Time = (Setup Time + Processing Time + Part Handling Time) / Number of Parts Produced

Setup time = 3.0 hours = 180 minutes

Processing time per cycle = 1.60 minutes x 2 = 3.20 minutes

Part handling time per cycle = 45 seconds x 2 = 1.50 minutes

Irregular work element time = 3.0 minutes

Cycle Time = (180 + 3.20 + 1.50 + 3.0) / 2 = 94.85 seconds

Therefore, the average cycle time is 94.85 seconds.

(b) Time to Complete the Batch:

To calculate the time required to complete the batch, we need to multiply the batch quantity by the cycle time.

Time to Complete Batch = Batch Quantity x Cycle Time

Time to Complete Batch = 2,400 x 94.85 seconds = 227,640 seconds

Therefore, the time required to complete the batch is 227,640 seconds, or approximately 63.23 hours.

(c) Average Production Rate:

The average production rate can be calculated as the batch quantity divided by the time to complete the batch.

Average Production Rate = Batch Quantity / Time to Complete Batch

Average Production Rate = 2,400 / 227,640 seconds = 0.0105 units per second

Therefore, the average production rate is 0.0105 units per second.

Learn more about  average cycle time at https://brainly.com/question/29396821

#SPJ1

The schedule variance is Rs.[tex](-) 9,000/- (SV = EV - PV)[/tex], the cost performance index (CPI) is [tex]1.03 (CPI = EV / AC)[/tex], and the time variance, assuming a linear relationship between time and cost, is Rs.[tex](-) 1,500/- (TV = SV / CPI)[/tex]. The cost variance is Rs[tex]6,000/- (CV = EV - AC)[/tex].

Great methods for assessing the health of a project include schedule and cost variance. You should keep an eye out for any changes in these variations as the project manager. Your endeavour is moving along well if both variances are positive.

Positive cost differences are a good sign that the project was finished on time and within budget.

To know more about cost variance  visit:

https://brainly.com/question/15178583

#SPJ9

When the temperature outside increases from 0°C to 40°C, what happens to the strong steel pins that clamp a 30 m segment of railroad track to the ground at both ends

As the temperature rises from 0°C to 40°C, the steel pins that clamp the 30 m segment of railroad track to the ground at both ends will expand in length. Steel expands when it heats up and contracts when it cools down. As a result, the pins will expand to keep the track in place, avoiding it from moving or becoming unstable at any point.The coefficient of thermal expansion for steel is about 12 x 10^-6 per degree Celsius (°C) or 12 x 10^-6 per Kelvin (K). Therefore, when the temperature rises from 0°C to 40°C, the increase in temperature will result in a lengthening of the steel pins by approximately:12 x 10^-6 x (40°C - 0°C) x 30 m = 0.0144 m or 14.4 mmThe steel pins that clamp the railroad track to the ground will lengthen by 14.4 mm.
When the temperature rises to 40°C, the railroad track will expand due to the increase in temperature. Since it is clamped by strong steel pins at both ends, the pins will experience additional stress and pressure as the track expands.

Learn more about steel pins here;

https://brainly.com/question/27961099

#SPJ4

The maximum stresses of the section near the fixed end are Bending stress, -10.16 ksi and Shear stress, 1.89 ksi.

To determine the maximum stresses at a section near the fixed end of the beam, calculate the bending stress and the shear stress.

First, let's find the reactions at the fixed end of the beam. Since the beam is completely fixed, the reactions will be equal and opposite to the applied force, which means:

Rx = -Fx = -400 lb

Ry = -Fy = 300 lb

Rz = -Fz = 1200 lb

Next, calculate the bending moment caused by the applied force. Since the force passes through the centroid of the beam, we can assume that the moment arm is equal to half the depth of the beam, which is 4.055 inches. Therefore, the bending moment at the section near the fixed end is:

M = Fz × 4.055 in = -4875 lb·in

Using the moment of inertia about the x-axis (centroidal-longitudinal axis), calculate the bending stress:

σx = M × (H/2) / Ix = -10.16 ksi

Next, calculate the shear stress using the shear force caused by the applied force. Since there is no other load on the beam, the shear force at the section near the fixed end is equal to the reaction force in the y-direction, which is 300 lb. Using the area of the web, calculate the shear stress:

τ = V × (W × t) / (2 × Iy) = 1.89 ksi

where V is the shear force, W is the width of the web, t is the thickness of the web, and Iy is the moment of inertia about the y-axis (centroidal-vertical axis). Note that we assume the shear stress distribution is uniform across the thickness of the web.

Therefore, the maximum stresses at the section near the fixed end of the beam are:

Bending stress: σx = -10.16 ksi

Shear stress: τ = 1.89 ksi

The bending stress is compressive and larger in magnitude than the yield stress of the material, which means the beam will fail due to bending. The shear stress is relatively small and does not contribute significantly to the failure of the beam.

Find out more on critical stress here: https://brainly.com/question/29574481

#SPJ1

Image transcribed:

[8] AW 8x15 I-beam is loaded through the centroid with a force that has the following components:

Fx = 400 lb

Fy=-300 lb

Fz=-1200 lb

The x-axis is the centroidal-longitudinal axis of the beam; the Y-axis is the centroidal-vertical axis along the web and the Z-axis is the centroidal axis parallel to the flanges. The beam is completely fixed at the other end, which is at a distance of 15 in from the point of load application in x- direction. Determine the maximum (critical) stresses at a section near the fixed end. (A W 8X15 beam is a wide flange thin-walled I-beam with the following properties: Area = 4.44 in²

Depth = 8.11 in width = 4.015 in flange thickness = 0.315 in

Web thickness = 0.245 in Ix = 48 in

Iy = 3.4 in¹)

Section has the following properties:

Area = 4.44 in² Depth (H) = 8.11 in

Width (W) = 4.015 in Length (L) = 15 in

Flange thickness = 0.315 in

Web thickness = 0.245 in

1-48 in 13.4 in

Fx=400 lb, Fy=-300 lb, F = -1200 lb

Note that  the amount of heat rejected is 1213.2 kJ, the network output is 1146.1 kJ, and the thermal efficiency is 45.9%.

To solve this problem, we need to use the Carnot cycle equations for the given conditions:

a) The amount of heat rejected:

Qout = Qh * (Tc / Th)

where Qh is the heat absorbed from the high-temperature source, Tc is the temperature at which heat is rejected, and Th is the temperature at which heat is absorbed.

We are given that water changes from saturated liquid to saturated vapor, so we can use the enthalpy of vaporization to calculate the heat absorbed:

Qh = m * hfg

where m is the mass of water and hfg is the enthalpy of vaporization of water.

From steam tables, at 250°C and 10 kPa, hfg = 2242.2 kJ/kg.

Assuming a mass of 1 kg, Qh = 2242.2 kJ.

Tc = 10°C + 273.15 = 283.15 K

Th = 250°C + 273.15 = 523.15 K

Qout = Qh * (Tc / Th) = 2242.2 * (283.15/523.15) = 1213.2 kJ

b) The network output:

W = Qh - Qout = Qh * (1 - Tc/Th)

W = 2242.2 * (1 - 283.15/523.15) = 1146.1 kJ

c) Thermal efficiency:

The thermal efficiency of a Carnot cycle is given by:

η = 1 - Tc/Th

η = 1 - 283.15/523.15 = 0.459 or 45.9%

Therefore, the amount of heat rejected is 1213.2 kJ, the network output is 1146.1 kJ, and the thermal efficiency is 45.9%.

Learn more about Thermal efficiency at:

https://brainly.com/question/13039990

#SPJ1

Note that the magnitude of the resultant active thrust on the wall is 876.69 kN.

To calculate the magnitude of the resultant active thrust on the wall, we need to use Rankine's theory of earth pressure.

Let's assume that the wall height is also 5.4 meters, and the angle of wall friction is zero.

Then, the total active thrust (Q) is given by:

Q = Ka * H * gamma * H/2

Where,

Ka = Active earth pressure coefficient

H = height of the wall

gamma = unit weight of soil

The active earth pressure coefficient can be calculated using the following formula:

Ka = (1 - sin(phi)) / (1 + sin(phi))

Where, phi = angle of shearing resistance of soil

Substituting the given values, we get:

phi = 30 degrees

H = 5.4 meters

gamma = 19.8 kN/m^3

Ka = (1 - sin(30)) / (1 + sin(30)) = 1/3

Q = Ka * H * gamma * H/2 = (1/3) * 5.4 * 19.8 * 5.4/2 = 876.69 kN

Therefore, the magnitude of the resultant active thrust on the wall is 876.69 kN.

The line of action of the resultant active thrust on the wall will be at one-third of the height of the wall from the bottom. Therefore, the line of action of the active thrust will be at a height of 1.8 meters from the bottom of the wall.

Learn more about magnitude  at:

https://brainly.com/question/15681399?

#SPJ1

According to the given question, the statement tech b says that the egr valve will not function during tle wide-open throt (wot) is correct.What is the Exhaust Gas Recirculation Valve (EGR)

An EGR (Exhaust Gas Recirculation) valve is utilized to cut nitrogen oxides (NOx) in the exhaust gases by limiting the oxygen supply to the fuel mix. In the internal combustion engine, this is a significant factor in pollution control. This valve mixes recirculated exhaust gas with incoming air to lessen the quantity of NOx created by the engine.Let's understand the statements given by Tech A and Tech B. Tech A says that the exhaust gas recirculation (EGR) valve does not function at idle. This statement is not correct because the EGR valve functions at idle. When the engine is idling, exhaust gases are passed back into the intake manifold through the EGR valve to help prevent detonation.The statement tech b says that the egr valve will not function during wide-open throttle (WOT) is correct. This statement is true because during the WOT condition, the EGR valve does not function because it reduces the airflow entering the engine. This enables the engine to burn more fuel, producing more power and increasing the engine's output. Hence, Tech B is correct.
Both Tech A and Tech B are correct. The EGR valve does not function at idle, and it will not function during wide-open throttle. This is because recirculation of exhaust gases is not needed under these conditions.

Learn more about valve here;

https://brainly.com/question/7457644

#SPJ4

The value stored in 0x10000008 on a big-endian machine can't be determined without knowing the byte values at that address and the following bytes, as well as the data type being used.

On a big-endian machine, the value stored in 0x10000008 would depend on the memory address and data being stored there. Without additional information, it is impossible to determine the specific value stored at this memory address. Please provide the necessary information, and I'll be happy to help you find the value.

If you don't know what a big-endian is, here is a little explanation of it.

What is big-endian?

Big-endian refers to the byte order used in computer memory storage. In a big-endian system, the most significant byte is stored at the lowest address and the least significant byte is stored at the highest address. This is in contrast to little-endian systems, where the least significant byte is stored at the lowest address and the most significant byte is stored at the highest address.

#SPJ11

A set of control signals is a group of inputs to a digital circuit that determine its response. These control signals govern the operation of the circuit and determine its logical functionality.

The ideal set of control signals that are used in a digital circuit depends on the requirement of the circuit. As given, we have only 2-input NAND, NOR, XOR, XNOR gates, and inverters, which means we cannot make all other gates, and we have to select the appropriate set of control signals.Among the given gates, NAND and NOR gates can be used to implement all other logic gates. XOR gate can be obtained by combining NAND gates and inverters, while XNOR gate can be obtained by using NOR gates and inverters. However, when we use only NAND and NOR gates, the size of the circuit increases. Therefore, the preferred set of control signals among the given gates should be the combination of XOR and inverters.The XOR gate requires less logic than the implementation of XOR using NAND and NOR gates. The XOR gate can be used as a universal gate and is also used in various arithmetic and encryption circuits. Therefore, the preferred set of control signals should be XOR and inverters.

For more such question on digital circuit

https://brainly.com/question/30454379

#SPJ11

Aligning the cutting tool when performing a setup on a lathe involves positioning the tool to the same height as the center of the workpiece. This ensures that the tool is correctly aligned to the workpiece, which is crucial in ensuring a proper cut.

Operators should adjust the height of the cutting tool by using the tool post and compound slide. The tool post is used to hold the cutting tool while the compound slide adjusts the height of the tool. The cutting tool tip should be set at the same height as the center of the workpiece. Once the height is adjusted, the operator should make sure that the tool is aligned parallel to the axis of the lathe bed.

You can learn more about operators at: brainly.com/question/30891881

#SPJ11

The expected weight fraction of pearlite in the as-cooled microstructure of a steel containing 1.90 wt% C, when cooled relatively slowly to room temperature, is approximately 100%.

Mass of solute/total mass x 100The percent by weight (wt%) of carbon in steel is often used to characterize the material's composition. Steel is an alloy consisting mainly of iron with a small amount of carbon, which is an alloy of iron and carbon with a carbon content of less than 2%.What is pearlite?Peralite is a two-phase microstructure made up of alternating layers of alpha-ferrite (an iron-rich solid solution of carbon in body-centered cubic iron) and cementite (an iron carbide with the chemical formula Fe3C). Peralite is created by the eutectoid reaction in steel, which occurs when the steel is cooled slowly to a temperature below its eutectoid point.

Learn more about microstructure: https://brainly.com/question/15344532

#SPJ11

The number of teeth on the gear (Ng) is 51 and the theoretical center-to-center distance (CD) is 4.25 inches.

Given:

Number of teeth on the pinion (Np) = 17

Diametral pitch (Pd) = 8 teeth/inch

Pinion speed (Np(speed)) = 1317 rev/min

Gear speed (Ng(speed)) = 439 rev/min

To find the number of teeth on the gear (Ng) and the theoretical center-to-center distance (CD), we can use the following formulas:

Gear speed formula:

Np/Ng = Ng(speed) / Np(speed)

Center-to-center distance formula:

[tex]CD = \frac{(Np + Ng)}{(2 * P_d)}[/tex]

Let's substitute the given values and calculate [tex]N_g[/tex] and CD:

Using formula 1:

[tex]\frac{17}{N_g} =\frac{439}{1317}[/tex]

[tex]17 * 1317 = N_g * 439[/tex]

[tex]N_g = \frac{(17 * 1317)}{439}[/tex]

[tex]N_g = 51[/tex] (rounded to the nearest whole number)

Using formula 2:

[tex]CD = \frac{(17 + 51)}{(2 * 8)}[/tex]

[tex]CD = \frac{68}{16}[/tex]

CD = 4.25 inches (rounded to two decimal places)

learn more about Diametral pitch here:

https://brainly.com/question/18521964

#SPJ4

Here’s a brief explanation of how these three technological advancements have revolutionized the field of Mechanical Engineering.

Computer Assisted Design (CAD): One of the most widely utilized software design tools is CAD. It is used by engineers and designers to model, validate, and convey ideas prior to production. CAD software models are frequently utilized as inputs to various mechanical engineering and design tools1.

ii) 3D printing: Extra tools for producing goods on a CNC machine or 3D printer are available and are occasionally incorporated into the CAD program. This has enabled quick prototyping and the creation of complicated geometries that were previously impossible with typical manufacturing methods1.

iii) Simulation: Computer-Aided Engineering (CAE) encompasses a wide variety of studies. Before building physical prototypes, it conducts complicated tasks like as finite element analysis (FEA) and computational fluid dynamics (CFD).

Learn more about Mechanical Engineering at:

https://brainly.com/question/20434227

#SPJ1

Technician B is correct. A receiver/dryer supplies refrigerant vapor to the expansion valve.

A receiver/dryer is a component in the refrigeration system that receives refrigerant vapor from the compressor and cools it to a liquid state. It also removes any moisture and contaminants from the refrigerant stream. A receiver/dryer is usually placed in the high-pressure side of the system, after the condenser and before the expansion valve.

A receiver/dryer operates in two phases: drying and storage. In the drying phase, the desiccant absorbs any moisture that has accumulated in the system. Then, in the storage phase, the refrigerant is kept in the receiver/dryer to ensure that a steady flow of refrigerant reaches the expansion valve, which is typically the next component in the system after the receiver/dryer.

learn more about expansion valve here:

brainly.com/question/12975508

#SPJ4

Both technicians are partially correct, but neither of them is entirely accurate.

The expansion valve does play a role in preventing the evaporator from freezing, but it is not the only component responsible for this task. The expansion valve regulates the flow of refrigerant into the evaporator, which helps to maintain the proper temperature and pressure in the system. On the other hand, cycling the clutch also plays a role in preventing the evaporator from freezing, but it is not the primary mechanism. The clutch engages and disengages the compressor, which regulates the pressure in the refrigeration system. When the pressure drops too low, the evaporator can freeze. Therefore, both technicians are partially correct. However, a combination of various components such as the expansion valve, cycling clutch, and other controls is needed to prevent the evaporator from freezing.

Learn more about technician here:

https://brainly.com/question/14290207

#SPJ4

In the classful addressing scheme, a Class B network has a range of network addresses from 128.0.0.0 to 191.255.255.255. The first octet of a Class B network address is always in the range of 128 to 191 decimal (or 10000000 to 10111111 in binary), and the first two octets together represent the network portion of the address. The remaining two octets represent the host portion of the address.

Therefore, the correct answer is:

-128.0.x.y to 191.255.x.y

In the classful addressing scheme, the range of network addresses considered a class B is 128.0.0.0 to 191.255.255.255.

An IP address (Internet Protocol address) is a unique identifier assigned to each device connected to a computer network that uses the Internet Protocol for communication. It is a numerical label assigned to each device, such as a computer, router, or smartphone, that allows it to be identified and communicate with other devices on the network.

In the classful addressing scheme, the IP address is divided into three classes: A, B, and C. Class B IP addresses range from 128.0.0.0 to 191.255.255.255. The first octet of a Class B IP address represents the network portion, while the remaining three octets represent the host portion. This allows for up to 65,536 network addresses, each with up to 65,534 host addresses. Class B addresses are typically assigned to mid-sized organizations or ISPs.

To know more about IP address refer:
https://brainly.com/question/3805118

#SPJ11

The forces in all members using the Joint method are 12 kN and 18 kN

Start by identifying the external forces and reactions:

In this case, there are two external forces acting on the structure, and they are:

12 kN at point C and 18 kN at point F.

Applying the equations of equilibrium to each joint and solving for the forces in the members, we have

At joint C

sum of forces in x direction = 0:

sum of forces in y direction: DCUp = 12 kN

sum of moments = 0:

12 * 0 = 0

0 = 0

Solving these equations, we get:

DCUp = 12 kN

At joint F

sum of forces in x direction: EFG = 18 kN:

sum of forces in y direction = 0

sum of moments = 18 * 2 - 18 * 2

sum of moments = 0

Read more about forces at

https://brainly.com/question/12970081

#SPJ1

This permits the home's power to be connected and disconnected from the inverter as needed. It feeds AC voltage into an AC disconnect. Therefore, option e is correct.

A typical residential inverter is a device that converts direct current (DC) electricity into alternating current (AC) electricity for residential use. A typical residential inverter converts the DC voltage produced by the solar panels into AC voltage that is used in a home. A typical residential inverter weighs approximately 90 pounds and is about the size of a small suitcase.

Residential inverters, like all electrical equipment, must be mounted in a NEMA 3R-rated enclosure for outdoor usage. It is necessary to feed AC voltage from the inverter into an AC disconnect.

learn more about direct current (DC)

brainly.com/question/28305485

#SPJ4

The probability that both parts in the sample are defective is 0.0082

The number of ways to choose 2 parts from the 50 parts in the bin is given by the binomial coefficient:

C(50, 2) = 50! / (2! * (50 - 2)!) = 1,225

The number of ways to choose 2 defective parts from the 5 defective parts in the bin is:

C(5, 2) = 5! / (2! * (5 - 2)!) = 10

Therefore, the probability of selecting 2 defective parts from the bin can be calculated as:

P(2 defective parts) = C(5, 2) * C(45, 0) / C(50, 2)

where C(45, 0) = 1 and it is the number of ways to choose 0 non-defective parts from the remaining 45 non-defective parts in the bin.

Plugging in the values, we get:

P(2 defective parts) = 10 * 1 / 1,225

= 0.0082

Therefore, the probability that both parts is 0.0082

Read more about probability at

https://brainly.com/question/251701

#SPJ1

Based on the given information, we can conclude that Valve malfunction should be a possible cause of this condition.

There are several possible causes for a reciprocating compressor to achieve a maximum discharge pressure of 120 psig, even though the low side intake of the compressor was open to the atmosphere and the pressure held when the compressor was off. Some possible causes could include:

learn more about discharge pressure here:

brainly.com/question/29518689

#SPJ4

To improve the given code and fulfill the professor's requirements, you can make the following changes:

1. Add comments at the beginning of the program with your name, program name, and its purpose.
2. Properly indent the code and use meaningful variable names.
3. Add comments for variable declarations and major sections of the program.

Here's an updated version of the code:

```cpp
#include
using namespace std;

// Author: Your Name
// Program: Sum of Numbers
// Purpose: Read an integer from standard input, then read that many values from a file and display their total.

int main() {
   int inputValue, numberOfValues, totalSum = 0;
   
   // Input Section
   cout << "Enter the number of values: ";
   cin >> numberOfValues;
   cout << endl;

   // Looping and Calculation Section
   for (int i = 0; i < numberOfValues; i++) {
       cout << "Enter value " << i+1 << ": ";
       cin >> inputValue;
       totalSum = totalSum + inputValue;
       cout << endl;
   }

   // Output Section
   cout << "The sum of numbers is " << totalSum << endl;

   return 0;
}
```

This version of the code includes comments for each major section (input, looping, calculation, and output), uses more descriptive variable names, and has properly indented statements.

For such more question on variable

https://brainly.com/question/28248724

#SPJ11

All of the following are sources of emissions from current gasoline-fuelled motor vehicles except the HVAC system.

What is a gasoline-fueledb  engines Ab is an internal combustion engine that runs on gasoline fuel. It's called an internal combustion engine because combustion takes place inside the engine itself. This is different from external combustion engines, such as steam engines, which combust fuel outside the engine.The crankcase, the fuel system, and the tailpipe are all sources of emissions from current gasoline-fuelled motor vehicles. The crankcase is an oil reservoir for internal combustion engines, and it is a crucial component in the lubrication system. The crankcase can emit emissions from time to time.The fuel system distributes gasoline to the engine for combustion and is a significant source of emissions. When gasoline is burned, it emits pollutants such as hydrocarbons, nitrogen oxides, and carbon monoxide.The tailpipe is another significant source of emissions from gasoline-fuelled vehicles. Pollutants such as carbon monoxide, nitrogen oxides, and particulate matter are emitted from the tailpipe.HVAC systems are not a source of emissions from gasoline-fueled motor vehicles. Instead, they are responsible for maintaining the cabin's temperature and air quality by heating, ventilating, and cooling the air.
The HVAC system is not a source of emissions from current gasoline-fuelled motor vehicles.

Learn more about motor vehicles here;

https://brainly.com/question/13163444

#SPJ4

The weight of the bob perpendicular to the plane of circular motion is constant, resulting in a straightforward harmonic motion with the same time period regardless of the angle of swing, so the periodic time of a conical pendulum depends only on its depth.

The length of the rope, the semi-vertical angle, and the acceleration brought on by the location's gravity all affect how long a conical pendulum swings. T=2Lcosg is the formula used to calculate the conical pendulum's time interval.

A simple pendulum's time interval T is inversely proportional to the square root of length l of the pendulum i.e., T∝√l or T2∝l

To know more about harmonic motion visit:

https://brainly.com/question/30404816

#SPJ9

The statement "In a low pass filter, the cutoff frequency is affected only by the feedback resistor value, not the input resistor" is false.

What is a low pass filter? A low-pass filter is an electronic circuit that allows signals with frequencies lower than a certain threshold to pass through while filtering out signals with higher frequencies. The cutoff frequency is the frequency point at which the filter starts to attenuate the signal. The cutoff frequency can be changed by varying the value of the input and feedback resistors. In a low-pass filter, the cutoff frequency is determined by both the input resistor and the feedback resistor values. As a result, the given statement is false. The cutoff frequency in a low-pass filter is determined by the input and feedback resistor values. The formula for the cutoff frequency in a simple low-pass filter is given as :fc = 1 / (2 * π * R * C)where fc is the i cutoff frequency, R is the resistor value, and C is the capacitor value. In the given formula, both the resistor and capacitor  the cutoff frequency.

learn more about  frequency here:

https://brainly.com/question/5102661

#SPJ4