The initial consumption is 3,272.103 m³/h.
Given: The capacity of an evaporator is 2,650 m³/h,
the initial concentration is 50 g/L and the
final concentration is 295 g/L.
Due to management deficiencies, there is a loss of capacity.
To find: The initial consumption.
Solution : Loss of capacity = Final capacity - Initial capacity
Let's find the final capacity: Final capacity = 2,650 m³/h
Final concentration = 295 g/L
Initial concentration = 50 g/L
So, the loss of capacity = (Final concentration - Initial concentration) x Final capacity
(295 - 50) g/L x 2,650 m³/h= 64,675 g/h = 64.675 kg/h
Now, let's find the initial capacity :
Initial capacity = Final capacity + Loss of capacity= 2,650 m³/h + (64.675 kg/h × 3600 s/h) ÷ (1000 g/kg) ÷ (295 g/L) = 2,650 m³/h + 622.103 m³/h= 3,272.103 m³/h
Know more about consumption here:
https://brainly.com/question/16301948
#SPJ11
6.38 A steam turbine, operating isentropically, takes in superheated steam at 1,800 kPa and discharges at 30 kPa. What is the minimum superheat required so that the exhaust contains no moisture? What is the power output of the turbine if it operates under these conditions and the steam rate is 5 kg s Can w 2.4 Pass
To ensure that the exhaust of a steam turbine contains no moisture, a minimum superheat is required. The power output of the turbine can be calculated using the given conditions, assuming an isentropic process and a steam rate of 5 kg/s.
The minimum superheat required for the exhaust to contain no moisture, we need to consider the pressure conditions at the turbine's inlet and outlet. The turbine takes in superheated steam at 1,800 kPa and discharges it at 30 kPa.
To avoid any moisture in the exhaust, the steam must remain in a superheated state throughout the expansion process. The minimum superheat required can be determined by referring to steam tables or charts that provide information on the saturation curve and properties of steam at various pressures.
The power output of the turbine can be calculated using the given conditions. Assuming an isentropic process and a steam rate of 5 kg/s, the power output can be determined using the equation:
Power output = Mass flow rate * Specific enthalpy change
By referring to steam tables or charts, the specific enthalpy change can be calculated by subtracting the initial specific enthalpy at the turbine inlet from the final specific enthalpy at the turbine outlet. This will give the specific enthalpy drop across the turbine.
Using the specific enthalpy change and the given mass flow rate, the power output of the turbine can be determined. It is important to note that additional considerations, such as mechanical efficiency and any losses in the turbine, may affect the actual power output achieved.
Learn more about pressure : brainly.com/question/30673967
#SPJ11
16. Expression: The presence of substance X is preferred to the presence of substance Y in water-based mud. Select X and Y from the list below for the expression provided above. Calcium Lime Carbonate Hard water HS CO2 17. Explain in one sentence what the term "hard water" means. 18. When calcium enters the mud, what kind of change occurs in the clay structure of the mud.
X: Calcium Y: Hard water "Hard water" refers to water that contains high levels of dissolved minerals. Calcium entering the mud leads to the formation of calcium-clay complexes, causing a change in the claystructure.
X: Calcium
Y: Carbonate
"Hard water" refers to water that contains high levels of dissolved minerals, specifically calcium and magnesium ions, which can create scale and reduce the effectiveness of soaps and detergents.
When calcium enters the mud, it can cause a change in the clay structure by replacing sodium or potassium ions within the clay lattice, leading to the formation of calcium-clay complexes. This change can affect the rheological properties of the mud, such as its viscosity, fluid loss control, and filtration characteristics, which can impact drilling operations and overall mud performance.
To learn more about detergents click here, brainly.com/question/861449
#SPJ11
Natural gas (methane, assumed ideal) flows isothermally at 55°F in horizontal pipeline that is 20 miles long, with fr 0.0035, It was observed that the maximum flow rate could be obtained from the inlet pressure and exit pressure of 60.8 and 2.40 psia respectively. a) Calculate the mass flux of the gas (lbm/ft's). b) Derive expression of the mass velocity (G) in the pipeline from governing equation. c) Calculate the diameter of pipeline (ft).
The mass flux of the natural gas can be calculated by dividing the mass flow rate by the cross-sectional area of the pipeline. The mass velocity (G) in the pipeline can be derived from the governing equation by dividing the mass flux by the gas density.
a) To calculate the mass flux of the gas, we need to determine the mass flow rate and the cross-sectional area of the pipeline. The mass flow rate can be calculated using the given inlet and exit pressures, along with the known flow rate conditions. The cross-sectional area can be determined using the diameter of the pipeline.
b) The mass velocity (G) in the pipeline can be derived from the governing equation by dividing the mass flux by the gas density. The governing equation for steady-state, isothermal flow in a pipeline is given as G = ρV, where G is the mass velocity, ρ is the gas density, and V is the velocity of gas flow.
c) The diameter of the pipeline can be calculated using the cross-sectional area formula, A = π*(d/2)^2, where A is the cross-sectional area and d is the diameter of the pipeline. By rearranging the formula, we can solve for the diameter: d = √(4*A/π).
The mass flux, divide the mass flow rate by the cross-sectional area. The mass velocity (G) can be derived from the mass flux divided by the gas density. The diameter of the pipeline can be calculated using the cross-sectional area formula and rearranging it to solve for the diameter.
Learn more about velocity : brainly.com/question/18084516
#SPJ11
An 18 mL sample of hydrochloric acid, HCl(aq), in a flask was titrated with a primary standard solution of sodium carbonate, Na2CO3(aq). Methyl red was used as an indicator. The primary standard solution was prepared by dissolving 0. 53 g of sodium carbonate in enough water to make 100 mL of solution. In a single trial of the titration, the initial volume reading on the burette was 0. 21 mL and the final volume reading was 26. 23 mL.
(a) What volume of primary standard solution was used in this trial?
(b) What amount of sodium carbonate reacted with the acid, during this trial?
(c) What was the concentration of the hydrochloric acid solution?
(a) To determine the volume of the primary standard solution used in the trial, we subtract the initial volume reading from the final volume reading on the burette:
Volume used = Final volume - Initial volume
= 26.23 mL - 0.21 mL
= 26.02 mL
Therefore, 26.02 mL of the primary standard solution was used in this trial.
(b) The balanced chemical equation for the reaction between hydrochloric acid and sodium carbonate is:
[tex]2HCL(aq)[/tex][tex]+ Na_{2} Co_{3} (aq)[/tex]→[tex]2NaCL(aq) + H_{2} 0(1) + C0_{2} (g)[/tex]
From the balanced equation, we can see that the stoichiometric ratio between HCl and [tex]Na_{2} CO_{3}[/tex] is 2:1. This means that for every 2 moles of HCl, 1 mole of [tex]Na_{2} CO_{3}[/tex] reacts. Since we know the volume of HCl used in the trial (18 mL) and the volume of [tex]Na_{2} CO_{3}[/tex] used (26.02 mL), we can calculate the moles reacted:
Moles of [tex]Na_{2} CO_{3}[/tex] = (26.02 mL / 1000 mL) * (0.53 g / 100 g/mol) * (1 mol / 1 L)
= 0.013808 mol
Since the stoichiometric ratio is 2:1, the moles of HCl reacted will be half of the moles of [tex]Na_{2} CO_{3}[/tex] :
Moles of HCl reacted = 0.013808 mol / 2
= 0.006904 mol
(c) To calculate the concentration of the hydrochloric acid solution, we need to know the moles of HCl and the volume of the acid used. We already have the moles of HCl (0.006904 mol) and the volume of HCl used (18 mL). However, we need to convert the volume to liters:
Volume of HCl used = 18 mL / 1000 mL/L
= 0.018 L
Concentration of HCl = Moles of HCl / Volume of HCl used
= 0.006904 mol / 0.018 L
= 0.3836 mol/L or 0.3836 M
Therefore, the concentration of the hydrochloric acid solution is 0.3836 mol/L or 0.3836 M.
For more questions on stoichiometric ratio, click on:
https://brainly.com/question/31861063
#SPJ8
In a directly proportional relationship, the line graph plotted is a __________ line which passes through the origin. What one word completes the sentence?
In a direct proportional relationship, the line graph is a straight line which passes through the origin.
Direct proportion is a relationship in which we plot a straight line of the type
y = mx.This is the equation in which y is directly proportional to x and this line passes through origin.
there are many examples of direct proportion in which one quantity varies directly with other i.e. it either decreases or increases in proportion with other quantity.in such cases one variable is called dependent variable while the other is called independent variable.
For eg. if in a certain job the greater the number of workers will be more will be the amount of work done in a given time.
To know more about direct proportion check:
https://brainly.com/question/13800336
In a directly proportional relationship, the line graph plotted is a straight line which passes through the origin.
When two variables exhibit a directly proportional relationship, it means that as one variable increases, the other variable also increases by a consistent ratio or factor. In other words, the ratio of the two variables remains constant throughout. This constant ratio is often referred to as the proportionality constant.
When representing this relationship graphically, a straight line passing through the origin is observed. This indicates that for every increase or decrease in one variable, the other variable changes in direct proportion. This means that as one variable doubles, the other variable also doubles, and as one variable triples, the other variable also triples, and so on.
The line passing through the origin signifies that when both variables are zero, there is no quantity of either variable. As the values increase, they do so proportionally. Any point on the line represents a direct proportional relationship between the variables.
This type of graph is characterized by a linear relationship, where the slope of the line represents the constant rate of change or the proportionality constant. The steeper the slope, the greater the rate of change, indicating a stronger direct proportionality.
Overall, a straight line passing through the origin is a distinctive characteristic of a directly proportional relationship, representing the consistent ratio between the variables.
Know more about straight line here:
https://brainly.com/question/28526173
#SPJ8
Q1b
b) State what the acronym REACH stands for? Explain what chemical manufacturers, importers and users are required to do under the REACH legislation
REACH- Registration, Evaluation, Authorization, and Restriction of Chemicals. Under REACH, chemical manufacturers, importers, and users are required to fulfill certain obligations to ensure the safe use of chemicals EU.
Chemical manufacturers or importers are required to register substances they produce or import in quantities of one tonne or more per year. This involves providing information on the properties, uses, and potential hazards of the chemicals. Additionally, they need to perform safety assessments and, if necessary, propose risk management measures to ensure the safe handling and use of the substances.
Users of chemicals, such as industrial companies, are also obligated to communicate information on the safe use of substances down the supply chain. They need to provide relevant safety data sheets and ensure proper risk management measures are implemented during their activities involving chemicals.
The REACH legislation aims to improve the protection of human health and the environment by ensuring the safe management and use of chemicals. It encourages the substitution of hazardous substances with safer alternatives and promotes the responsible handling and communication of chemical-related information throughout the supply chain.
To learn more about chemical manufacturers click here, brainly.com/question/32266107
#SPJ11
please help!2008下
1. (20) The thermal decomposition of ethane is believed to follow the sequence below: initiation C₂H6> 2CH3. E₁ = 60 kcal/mol initiation CH3 + C₂H62 CH4 + C₂H5 • E2 = 10 kcal/mol propagation
The thermal decomposition of ethane is believed to follow the sequence: initiation: C₂H₆ → 2CH₃ (with an activation energy (E₁) of 60 kcal/mol), initiation: CH₃ + C₂H₆ → CH₄ + C₂H₅• (with an activation energy (E₂) of 10 kcal/mol), propagation: C₂H₅• → products.
The thermal decomposition of ethane (C₂H₆) involves two initiation steps and a propagation step. Here's a breakdown of the reaction sequence:
1. Initiation Step 1: C₂H₆ → 2CH₃
In this step, ethane decomposes to form two methyl radicals (CH₃). The activation energy (E₁) for this step is given as 60 kcal/mol.
2. Initiation Step 2: CH₃ + C₂H₆ → CH₄ + C₂H₅•
In this step, a methyl radical (CH₃) reacts with ethane to produce methane (CH₄) and an ethyl radical (C₂H₅•). The activation energy (E₂) for this step is given as 10 kcal/mol.
3. Propagation Step: C₂H₅• → products
The ethyl radical (C₂H₅•) generated in the initiation step undergoes further reactions to form products.
The thermal decomposition of ethane proceeds through a series of reactions involving initiation and propagation steps. The first initiation step converts ethane into two methyl radicals, while the second initiation step involves the reaction of a methyl radical with ethane to form methane and an ethyl radical. The propagation step involves the reactions of the ethyl radical to form the final products. The activation energies (E₁ and E₂) provided indicate the energy required for these steps to occur.
To know more about ethane , visit
https://brainly.com/question/28168286
#SPJ11
How many grams in 5.8 moles NaCI? with work please
[tex]n=\dfrac{m}{M}[/tex] where n is moles, m is mass and M is molar mass.
To solve for mass, isolate m:
[tex]m=nM[/tex]
Input given information:
[tex]m=5.8*58.44\\m=338.952\\m=340[/tex]
There are 340 g in 5.8 mol of NaCl.
Q1(A) (5) A binary liquid mixture is in equilibrium with its vapor at 300K. The liquid mole fraction of species 1 is 0.4 and the molar excess Gibbs free energy is 2001/mol If 7, -1.09, calculate the value of 7, denotes liquid-phase activity coefficient of species i in the binary mixture.
The liquid-phase activity coefficient (γ₁) of species 1 in the binary mixture at 300K, with a molar excess Gibbs free energy of 2001 J/mol, is approximately 2.226.
To calculate the value of the liquid-phase activity coefficient (γ₁) of species i in the binary mixture, we can use the equation:
ΔG_ex = RT * ln(γ₁)
where:
ΔG_ex is the molar excess Gibbs free energy (2001 J/mol in this case),
R is the gas constant (8.314 J/(mol·K)),
T is the temperature (300 K in this case),
ln denotes the natural logarithm,
γ₁ is the liquid-phase activity coefficient of species 1.
Rearranging the equation, we can solve for γ₁:
γ₁ = exp(ΔG_ex / (RT))
Substituting the given values, we get:
γ₁ = exp(2001 J/mol / (8.314 J/(mol·K) * 300 K))
γ₁ = exp(2001 / (8.314 * 300))
γ₁ = exp(0.801)
γ₁ ≈ 2.226
Therefore, the value of the liquid-phase activity coefficient (γ₁) of species 1 in the binary mixture is approximately 2.226.
Learn more about Gibbs free energy here: brainly.com/question/13795204
#SPJ11
carbon occurs naturally as____ and____
Answer:
gas, vapour
Explanation:
hope you like it
______________________________________
Urgent!!!! Please solve will all steps. There are already 2 answers
of this q im not sure which is right!!!
A reaction proceeds as follows: A + B => C + D Assume that the reaction is irreversible and its rate is r = 0.263 CACB (mol/L/min). Determine the concentration of the product ether as a function of ti
The resulting equation will relate the concentration of ether to time and may involve the integration of the concentrations of reactants A and B.
The given rate equation is r = 0.263 CACB (mol/L/min), where CACB represents the concentration of reactant A (A) multiplied by the concentration of reactant B (B). Assuming the reaction is irreversible, the rate equation represents the rate of formation of the product ether (C) over time.
To determine the concentration of ether (C) as a function of time, we need to integrate the rate equation with respect to time. The integration will yield an equation that relates the concentration of ether to time.
∫d[C]/dt = ∫0.263 CACB dt
Integrating both sides of the equation gives:
[C] = 0.263 ∫CACB dt
The integration of the concentration of A (CA) and B (CB) will depend on their initial concentrations and any additional information provided about their changes over time.
To determine the concentration of the product ether (C) as a function of time, the given rate equation needs to be integrated with respect to time. The resulting equation will relate the concentration of ether to time and may involve the integration of the concentrations of reactants A and B. Further information about the initial concentrations and changes in reactant concentrations over time is necessary to obtain a specific function relating the concentration of ether to time.
To know more about concentration, visit:
https://brainly.com/question/28564792
#SPJ11
2. (10 points) A compound sphere is given as below: T₂-30 °C B r3 A T₁=₁ 100°C Calculate Tw in °C at steady-state condition. r₁=50 mm r₂=100 mm r3= 120 mm KA=0.780 W/m°C KB=0.038 W/m°C
In this problem, a compound sphere with different materials and temperatures is given. The task is to calculate the temperature Tw at steady-state conditions.
The dimensions and thermal conductivities of the materials (KA and KB) are provided. Using the heat transfer equation and appropriate boundary conditions, the value of Tw can be determined. To calculate the temperature Tw at steady-state conditions in the compound sphere, we can use the heat transfer equation and apply appropriate boundary conditions. The compound sphere consists of two materials with different thermal conductivities, KA and KB, and three radii: r₁, r₂, and r₃.
The heat transfer equation for steady-state conditions can be expressed as:
(Q/A) = [(T₂ - T₁) / (ln(r₂/r₁) / KA)] + [(T₂ - Tw) / (ln(r₃/r₂) / KB)]
Where Q is the heat transfer rate, A is the surface area, T₁ is the initial temperature at the inner surface (r₁), T₂ is the initial temperature at the outer surface (r₃), and Tw is the temperature at the interface between the two materials. Since the problem states that the system is at steady-state conditions, the heat transfer rate (Q) is zero. By setting Q/A to zero in the equation, we can solve for Tw.
To do this, we rearrange the equation and solve for Tw:
Tw = T₂ - [(T₂ - T₁) / (ln(r₃/r₂) / KB)] * (ln(r₂/r₁) / KA)
By substituting the given values for T₁, T₂, r₁, r₂, r₃, KA, and KB into the equation, we can calculate the value of Tw.
It's important to note that the units of the given thermal conductivities (KA and KB) and dimensions (radii) should be consistent to ensure accurate calculations. Additionally, the temperatures T₁ and T₂ should be in the same temperature scale (e.g., Celsius or Kelvin) to maintain consistency throughout the calculation.
By following these steps and substituting the given values into the equation, the value of Tw can be determined, providing the temperature at the interface between the two materials in the compound sphere.
Learn more about heat transfer here:- brainly.com/question/30526730
#SPJ11
High strength low alloy steels are the new carbon steel in the
industry. They are
defined by multiple strengthening mechanism. Like
precipitation strengthening and grain size reduction. Explain their
High-strength low-alloy steels are defined by multiple strengthening mechanisms such as precipitation strengthening and grain size reduction.
High-strength low-alloy steels are defined by multiple strengthening mechanisms, including precipitation strengthening and grain size reduction. These steels have replaced carbon steel in the industry. They are alloyed with small amounts of elements such as manganese, nickel, chromium, and copper to increase their strength, toughness, and durability.
Precipitation hardening occurs when small particles are added to a material, and their presence increases the strength of the material. High-strength low-alloy steels, which contain small amounts of alloying elements such as vanadium, titanium, or niobium, utilize precipitation hardening to increase strength.
When the steel is heated to high temperatures, the small particles dissolve and the steel becomes soft. The steel is then cooled, and the particles are forced to precipitate out of the solution and form small, evenly distributed particles in the steel's microstructure.
Grain size reduction is another mechanism that contributes to the strength of high-strength low-alloy steels. The microstructure of a metal is made up of grains, and a material with smaller grains has a higher strength because the boundaries between the grains provide more resistance to deformation. Grain size reduction is achieved through thermomechanical processing, where the steel is heated to a high temperature and then rapidly cooled. This process increases the number of nucleation sites in the steel and results in a greater number of small grains.
Know more about steels here:
https://brainly.com/question/31055468
#SPJ11
The microbial fermentation of A produces R as follows 10A Cell catego ISR + 2 Cells and experiments in a mixed flow reactor with CA = 250 mol'm' show that C₂ = 24 mol/m' when r= 1.5 hr C₂ = 30 mol/m when 7= 3.0 hr In addition, there seems to be a limiting upper value for C, at 36 mol/ m³ for any r. C₁, or C. Cont From this information determine how to maximize the fractional yield of R. or (R/A), from a feed stream of 10 m³/hr of CA 350 mol/m². Cell or product separation and recycle are not practical in this system, so only consider a once-through system. Present your answer as a sketch showing reactor type, reactor volume, Cg in the exit stream, and the moles of R produced/hr. H
To maximize the fractional yield of R (R/A) in a once-through system with the given information, a plug-flow reactor (PFR) should be used. The reactor volume should be determined based on the desired fractional yield and the limiting upper value for C. In this case, a reactor volume of 36 m³ is recommended. The exit stream concentration (Cg) will be 36 mol/m³, and the moles of R produced per hour can be calculated based on the feed stream flow rate and the fractional yield.
Given data:
- Feed stream flow rate (CA) = 10 m³/hr
- Feed stream concentration (CA) = 350 mol/m³
- C₂ concentration at r = 1.5 hr = 24 mol/m³
- C₂ concentration at r = 3.0 hr = 30 mol/m³
- Limiting upper value for C = 36 mol/m³
To maximize the fractional yield of R (R/A), we need to operate the reactor at the conditions where the concentration of C₂ is closest to the limiting upper value of 36 mol/m³.
Based on the given data, the closest concentration of C₂ to 36 mol/m³ is achieved at r = 3.0 hr with a concentration of 30 mol/m³. Therefore, we will choose an intermediate residence time of 3.0 hr for the PFR.
To calculate the reactor volume, we can use the equation:
V = Q / (CA - Cg)
Where:
V = Reactor volume
Q = Feed stream flow rate
CA = Feed stream concentration
Cg = Exit stream concentration
Substituting the given values:
V = 10 m³/hr / (350 mol/m³ - 30 mol/m³)
V ≈ 0.0323 m³ ≈ 32.3 L
Therefore, the recommended reactor volume is approximately 32.3 L.
The exit stream concentration (Cg) will be 36 mol/m³, which is the limiting upper value for C.
To calculate the moles of R produced per hour, we can use the equation:
Moles of R produced/hr = Q * (Cg - CA) * (R/A)
Where:
Q = Feed stream flow rate
Cg = Exit stream concentration
CA = Feed stream concentration
(R/A) = Fractional yield of R
Substituting the given values:
Moles of R produced/hr = 10 m³/hr * (36 mol/m³ - 350 mol/m³) * (R/A)
Since the fractional yield of R (R/A) is not provided in the given information, it cannot be calculated without additional data.
To maximize the fractional yield of R (R/A) in a once-through system, a plug-flow reactor (PFR) with a volume of approximately 32.3 L is recommended. The exit stream concentration (Cg) will be 36 mol/m³. The moles of R produced per hour can be calculated once the fractional yield (R/A) is known.
To know more about fractional yield, visit
https://brainly.com/question/25996347
#SPJ11
EXP # {A} (M) {B} (M) 1 0.100 0.100 2 0.300 0.100 3 0.300 0.200 4 0.150 0.600 RATE (M/s) 0.250 0.250 1.00 9.00 Given the above table of data, what is the rate when (A) = 0.364 M and {B} = 0.443 M?
The rate when (A) = 0.364 M and {B} = 0.443 M is approximately 0.525 M/s.
The rate when (A) = 0.364 M and {B} = 0.443 M, we need to interpolate between the data points provided in the table. First, we identify the two closest data points: (A) = 0.300 M and (B) = 0.100 M, and (A) = 0.300 M and (B) = 0.200 M.
Next, we calculate the rate at these two points using the formula: Rate = (M2 - M1) / ({B}2 - {B}1), where M1 and M2 are the corresponding values of (A) at the data points, and {B}1 and {B}2 are the corresponding values of {B} at the data points.
Using the formula, we find the rates to be 0.250 M/s and 1.00 M/s, respectively.
Finally, we interpolate between these two rates based on the difference between the desired (A) and the nearest (A) value in the table (0.364 M - 0.300 M). The interpolated rate is calculated as: Interpolated rate = Rate1 + ((Rate2 - Rate1) * ((A) - (A)1) / ((A)2 - (A)1)), where Rate1 and Rate2 are the rates calculated at the closest data points, and (A)1 and (A)2 are the corresponding values of (A) at the data points.
Plugging in the values, we obtain the interpolated rate as approximately 0.525 M/s when (A) = 0.364 M and {B} = 0.443 M.
Learn more about interpolate : brainly.com/question/30766144
#SPJ11
Different between lamellar and spherullites
Lamellae are individual flat layers that form during crystallization, while spherulites are larger structures made up of multiple radiating lamellae. Lamellae provide materials with enhanced mechanical properties, while spherulites can have both structural and optical effects.
Lamellae and spherulites are two distinct microstructures that can form in certain materials, particularly polymers. Here's the difference between them:
Lamellae:
- Lamellae are thin, flat layers or sheets that are parallel to each other within a material.
- They form when the material undergoes a process called crystallization, where the polymer chains arrange themselves in an ordered and repetitive manner.
- Lamellae have a lamellar morphology, meaning they appear as stacked layers or plate-like structures.
- They typically have a high degree of structural regularity and alignment, which gives the material enhanced mechanical properties such as strength and stiffness.
Spherulites:
- Spherulites are spherical or roughly spherical structures that consist of multiple lamellae radiating out from a central nucleation point.
- They form during the crystallization process as well, but with a different growth pattern compared to lamellae.
- Spherulites are characterized by a radial arrangement of lamellae, resembling a flower-like or radial pattern when observed under a microscope.
- They often have a more complex structure compared to lamellae and can exhibit variations in lamellar thickness, orientation, and branching.
- Spherulitic structures can affect the material's optical properties, such as transparency or opacity, as well as its mechanical properties.
Learn more about polymer at https://brainly.com/question/24632066
#SPJ11
Propylene is converted to butyraldehyde and n-butanol in the following reaction sequence in a catalytic reactor: C3H6+ CO + H₂CH₂CHO (butyraldehyde) C3H/CHO + H₂ C4H,OH (n-butanol) - Products ar
In the given reaction sequence, propylene (C3H6) is converted to butyraldehyde (C4H8O) and n-butanol (C4H10O) in a catalytic reactor.
The reaction sequence involves two steps. Let's break down each step and calculate the products formed:
Step 1: C3H6 + CO + H2 → C4H8O (butyraldehyde)
In this step, propylene (C3H6) reacts with carbon monoxide (CO) and hydrogen (H2) to produce butyraldehyde (C4H8O).
Step 2: C4H8O + H2 → C4H10O (n-butanol)
In this step, butyraldehyde (C4H8O) reacts with hydrogen (H2) to produce n-butanol (C4H10O).
Propylene is converted to butyraldehyde and n-butanol through a two-step reaction sequence in a catalytic reactor.
The first step involves the reaction of propylene, carbon monoxide, and hydrogen to form butyraldehyde. The second step involves the reaction of butyraldehyde with hydrogen to produce n-butanol.
Propylene is converted to butyraldehyde and n-butanol in the following reaction sequence in a catalytic reactor: C3H6+CO+ H₂CH/CHO (butyraldehyde) C₁H-CHO+ H₂CH₂OH (n-butanol) Products are fed to a catalytic reactor. The reactor effluent goes to a flash tank and catalyst recycled to the reactor. The reaction products are separated, the product stream is subjected to additional hydrogenation (use only reaction 2) with excess hydrogen, converting all of the butyraldehyde to butanol. The conversion of 1" reaction is given as 40% by mole C)Hs. The 2nd reaction conversion is given as 45% by mole C,H-CHO. Calculate the unkown flow rates in the given process for the given constraints. nis must be equal to 12 mol C,He and n17 and nis must be 4 mol CO and 3 mol H₂, respectively. 40 NCH CH CHƠI n 12.0 mol CH M Mei act₂ Aut mol C.H. mol CO Reactor Flash IN: My nu Separation 4.0 mol CO 1.0 mol H₂ (2 Reaction) Tank nu! mol H₂ P mol C₂H,CHO P₂² ny Pa mal C,H,OH P: nyt mol C,H,CHO mol CHLOH n₂ mol H₂ Hydrogenerator (One Reaction) mol CO mol H₂ mol C The mol CO mol H₂ mol CH CHO mol C,H,OH mol cat mol cat n mol H₂ mal CCOH
To learn more about reactor, visit
brainly.com/question/10475418
#SPJ11
You have been given a task to investigate how colour/paint can influence energy consumption in our laboratories and auditoriums. Although you did not get an opportunity to perform an experiment, but based on your knowledge, answer the following question. a. Do you think colour/paint of the laboratories and auditoriums can have significant energy saving effect? (1) b. If you are given the colours: red, black, and white, which colour do you think can have a significant energy? (2) c. Discuss and explain how the colour you have chosen can really save energy, in terms of temperature? (6) d. Give five benefits of changing colour/paint of the laboratories and auditoriums? (5) e. Explain in detail the types of energy/energies (specifically temperature) influenced by colour/paint and how this energy can be lost and the costs involved?
The color or paint of laboratories and auditoriums can indeed have a significant energy-saving effect. Different colors absorb and reflect light differently, which can impact the temperature and energy consumption within the space. While an experiment was not conducted, based on knowledge and understanding, color choice can play a role in energy efficiency.
1. The color red is known to absorb more light and heat, which can increase the temperature in a space. Therefore, it may not have a significant energy-saving effect compared to other colors.
2. Black color also absorbs more light and heat, leading to higher temperatures. It is likely to contribute to increased energy consumption rather than energy savings.
3. On the other hand, the white color reflects more light and heat, keeping the space cooler. By reflecting sunlight and reducing heat absorption, it can contribute to energy savings.
4. The reflection of light and heat by white color helps in reducing the need for cooling systems and air conditioning, thus reducing energy consumption and associated costs.
5. Benefits of changing color/paint in laboratories and auditoriums include improved energy efficiency, reduced cooling and heating costs, enhanced comfort for occupants, a more visually appealing environment, and a positive impact on the overall sustainability and environmental footprint.
6. The type of energy influenced by color/paint is primarily thermal energy, which is related to temperature. Different colors absorb or reflect light, which affects the amount of heat transferred to or from the surroundings. By reducing heat absorption, the cooling load on HVAC systems is reduced, resulting in energy savings and lower costs. Additionally, the choice of color can impact visual perception, psychological factors, and the overall ambiance of the space.
To know more about auditorium click here:
https://brainly.com/question/15387100
#SPJ11
4.8 The vapour pressure, P. (measured in mm Hg) of 11quid arsenic, is given by Tog P2.40 + 6.69, and that of solid arsenic by Tog P = -6,947 +10.8. Calculate the temperature at which the two forms of
The temperature at which the two forms of arsenic are in equilibrium is 827.97 K.
We have the following formula for the vapour pressure of liquid and solid arsenic.
Tog P2.40 + 6.69 for the liquid form and
Tog P = -6,947 +10.8 for the solid form.
The temperature at which the two forms of arsenic are in equilibrium can be calculated using the formula:
Tog P2.40 + 6.69 = Tog P = -6,947 +10.8
We can write the above equation as:
2.40T + 6.69 = -6,947 + 10.8T where T is the temperature at which the two forms of arsenic are in equilibrium.
Now, we will solve the above equation for T:2.40T - 10.8T = -6,947 - 6.69-8.4T = -6953.69T = 827.97 K
Know more about equilibrium here:
https://brainly.com/question/31730245
#SPJ11
Inside a certain isothermal gas-phase reactor, the following reaction achieves equilibrium: 1 A+ 4B2C Ka = 5.0 2 Assume the contents are an ideal-gas mixture, and the Ka reported above is at the react
In the isothermal gas-phase reactor, the equilibrium constant (Ka) for the reaction 1 A + 4 B ⇌ 2 C is 5.0. The value of Ka provided is at the reaction temperature.
The equilibrium constant, Ka, is given as 5.0 for the reaction 1 A + 4 B ⇌ 2 C. The equilibrium constant is a measure of the ratio of the concentrations of the products to the concentrations of the reactants at equilibrium.
In this case, the equilibrium constant expression can be written as follows:
Ka = [C]^2 / ([A] * [B]^4)
The numerical value of Ka indicates the relative concentrations of the products and reactants at equilibrium. A higher value of Ka suggests a higher concentration of products compared to reactants, indicating that the reaction favors the formation of products at equilibrium.
It's important to note that the provided value of Ka is specific to the given reaction at the particular temperature at which the equilibrium is achieved. The temperature plays a crucial role in determining the equilibrium constant.
In the isothermal gas-phase reactor, the equilibrium constant (Ka) for the reaction 1 A + 4 B ⇌ 2 C is 5.0. The value of Ka indicates that the reaction favors the formation of products at equilibrium. The equilibrium constant is specific to the given reaction at the temperature at which equilibrium is achieved.
To know more about isothermal gas-phase reactor , visit
https://brainly.com/question/14789055
#SPJ11
mass transfer
Problem #5 Determine the diffusivity of Ethanol in Toluene at 30°C using the equation of Wilke and Chang and the equation of Sitaraman et al. Convert the diffusivity to 15°C and compare with experim
The diffusivity of ethanol in toluene at 30°C using the Wilke and Chang equation is approximately 7.46 × 10^(-10) m²/s
To determine the diffusivity of ethanol in toluene at 30°C, we can use two equations: the Wilke and Chang equation and the equation of Sitaraman et al. Let's calculate the diffusivity using both equations and then convert the result to 15°C for comparison with experimental data.
Wilke and Chang Equation: The Wilke and Chang equation for binary diffusion coefficient (D_AB) is given by:
D_AB = (1.858 × 10^(-4) * T^1.75) / (M_A^0.5 + M_B^0.5)
where: T is the temperature in Kelvin (30°C = 303 K) M_A and M_B are the molecular weights of the components (ethanol and toluene)
The molecular weights of ethanol (C2H5OH) and toluene (C7H8) are approximately: M_ethanol = 46 g/mol M_toluene = 92 g/mol
Substituting the values into the equation: D_AB = (1.858 × 10^(-4) * 303^1.75) / (46^0.5 + 92^0.5) D_AB ≈ 7.46 × 10^(-10) m²/s
Equation of Sitaraman et al.: The equation of Sitaraman et al. for diffusivity (D_AB) is given by:
D_AB = 2.63 × 10^(-7) * (T/273)^1.75
Substituting the temperature of 30°C: D_AB = 2.63 × 10^(-7) * (303/273)^1.75 D_AB ≈ 1.43 × 10^(-8) m²/s
To convert the diffusivity to 15°C, we can use the following equation:
D_15 = D_30 * (T_15/T_30)^(3/2)
where: D_15 is the diffusivity at 15°C D_30 is the diffusivity at 30°C T_15 is the temperature in Kelvin (15°C = 288 K) T_30 is the temperature in Kelvin (30°C = 303 K)
Using this equation, we can calculate D_15 for both methods.
For the Wilke and Chang equation: D_15_WC = D_AB * (288/303)^(3/2) D_15_WC ≈ 7.01 × 10^(-10) m²/s
For the equation of Sitaraman et al.: D_15_Sitaraman = D_AB * (288/303)^(3/2) D_15_Sitaraman ≈ 3.86 × 10^(-9) m²/s
In conclusion, the diffusivity of ethanol in toluene at 30°C using the Wilke and Chang equation is approximately 7.46 × 10^(-10) m²/s, and using the equation of Sitaraman et al. is approximately 1.43 × 10^(-8) m²/s. After converting to 15°C, the diffusivity according to the Wilke and Chang equation is approximately 7.01 × 10^(-10) m²/s, and according to the equation of Sitaraman et al. is approximately 3.86 × 10^(-9) m²/s. These values can be compared with experimental data to assess the accuracy of the models.
To know more about diffusivity , visit :
https://brainly.com/question/14852229
#SPJ11
Propylene is converted to butyraldehyde and n-butanol in the following reaction sequence in a catalytic reactor: C3H6+CO+ H₂CH/CHO (butyraldehyde) C₁H-CHO+ H₂CH₂OH (n-butanol) Products are fed
In the given reaction sequence, propylene (C3H6) is converted to butyraldehyde (C4H8O) and n-butanol (C4H10O) in a catalytic reactor.
The reaction sequence involves two steps. Let's break down each step and calculate the products formed:
Step 1: C3H6 + CO + H2 → C4H8O (butyraldehyde)
In this step, propylene (C3H6) reacts with carbon monoxide (CO) and hydrogen (H2) to produce butyraldehyde (C4H8O).
Step 2: C4H8O + H2 → C4H10O (n-butanol)
In this step, butyraldehyde (C4H8O) reacts with hydrogen (H2) to produce n-butanol (C4H10O).
Propylene is converted to butyraldehyde and n-butanol through a two-step reaction sequence in a catalytic reactor.
The first step involves the reaction of propylene, carbon monoxide, and hydrogen to form butyraldehyde. The second step involves the reaction of butyraldehyde with hydrogen to produce n-butanol.
Propylene is converted to butyraldehyde and n-butanol in the following reaction sequence in a catalytic reactor: C3H6+CO+ H₂CH/CHO (butyraldehyde) C₁H-CHO+ H₂CH₂OH (n-butanol) Products are fed to a catalytic reactor. The reactor effluent goes to a flash tank and catalyst recycled to the reactor. The reaction products are separated, the product stream is subjected to additional hydrogenation (use only reaction 2) with excess hydrogen, converting all of the butyraldehyde to butanol. The conversion of 1" reaction is given as 40% by mole C)Hs. The 2nd reaction conversion is given as 45% by mole C,H-CHO. Calculate the unkown flow rates in the given process for the given constraints. nis must be equal to 12 mol C,He and n17 and nis must be 4 mol CO and 3 mol H₂, respectively. 40 NCH CH CHƠI n 12.0 mol CH M Mei act₂ Aut mol C.H. mol CO Reactor Flash IN: My nu Separation 4.0 mol CO 1.0 mol H₂ (2 Reaction) Tank nu! mol H₂ P mol C₂H,CHO P₂² ny Pa mal C,H,OH P: nyt mol C,H,CHO mol CHLOH n₂ mol H₂ Hydrogenerator (One Reaction) mol CO mol H₂ mol C The mol CO mol H₂ mol CH CHO mol C,H,OH mol cat mol cat n mol H₂ mal CCOH
To learn more about reactor, visit
https://brainly.com/question/10475418
#SPJ11
with step-by-step solution
45. A 0.010F weak acid is 4.17% ionized. What is the ionization constant? a. 1.8 x 10-5 b. 3.6 x 10-5 c. 1.2 x 10-4 d. 1.2 x 10-5
The ionization constant (Ka) of the weak acid with 4.17% ionization and a concentration of 0.010F is approximately 1.2 x 10^-5 (option d).
The percent ionization of a weak acid is the ratio of the concentration of ionized acid ([A-]) to the initial concentration of the acid ([HA]), multiplied by 100%.
Given that the percent ionization is 4.17%, we can write it as:
4.17% = ([A-]/[HA]) * 100
Since the concentration of the acid ([HA]) is 0.010F, we can rewrite the equation as:
4.17% = ([A-]/0.010F) * 100
Dividing both sides of the equation by 100, we get:
0.0417 = [A-]/0.010F
Rearranging the equation, we have:
[A-] = 0.0417 * 0.010F
= 0.000417F
The concentration of the ionized acid ([A-]) can be used to determine the concentration of the non-ionized acid ([HA]) using the initial concentration:
[HA] = [HA]initial - [A-]
= 0.010F - 0.000417F
= 0.009583F
The ionization constant (Ka) is given by the ratio of the concentration of the ionized acid ([A-]) to the concentration of the non-ionized acid ([HA]):
Ka = [A-]/[HA]
= (0.000417F) / (0.009583F)
≈ 4.35 x 10^-5
Therefore, the ionization constant (Ka) of the weak acid with 4.17% ionization and a concentration of 0.010F is approximately 1.2 x 10^-5 (option d).
The ionization constant (Ka) of the weak acid with 4.17% ionization and a concentration of 0.010F is approximately 1.2 x 10^-5 (option d).
To know more about Ka , visit;
https://brainly.com/question/32606490
#SPJ11
How
to make Ephedrine in lab/home?
chemicals required, quantity? Procedure?
Ephedra plants are extracted to create natural ephedrine. The plant Ephedra sinica and other members of the genus Ephedra are the sources of ephedrine, which takes its name from these plants. China produces a significant amount of the raw materials used to make ephedrine and traditional Chinese medicines.
A drug called ephedrine is employed to control and treat clinically significant hypotension. It belongs to the group of medications called sympathomimetics. The primary FDA-approved use of ephedrine is to treat clinically severe hypotension during surgery. Only ephedrine and pseudoephedrine were able to create the usual, stable violet colour that was needed for the testing process and the colour reference in the UN test kit.
To learn more about ephedrine, click here.
https://brainly.com/question/28260101
#SPJ4
A soil contains 2000 mg N/ kg of soil in organic forms. The rate of mineralization is 3% per year. A) How many mg of N/ kg of soil is mineralized every year? B) the mass of the soil is 2 000 000 kg/ha, calculate the kg of N mineralized/ ha of soil. Show your work.
Answer:
a) how many mg of n/ kg of soil is mineralized every year? Nitrogen mineralized every year = 60 mg N/kg of soil
b)the mass of the soil is 2,000,000 kg/ha, calculate the kg of n mineralized/ ha of soil.
120 kg/ha of nitrogen is mineralized every year.
Explanation:
To calculate the amount of nitrogen mineralized every year, we can use the formula:
Nitrogen mineralized every year = Nitrogen in organic forms x Mineralization rate
From the problem statement, we know that the soil contains 2000 mg N/kg of soil in organic forms and the rate of mineralization is 3% per year.
Substituting these values into the formula above, we get:
Nitrogen mineralized every year = 2000 mg N/kg of soil x 3%
Nitrogen mineralized every year = 60 mg N/kg of soil
To calculate the kg of N mineralized/ha of soil, we can use the formula:
kg of N mineralized/ha of soil = (Nitrogen mineralized every year x Mass of soil)/1000
From the problem statement, we know that the mass of the soil is 2 000 000 kg/ha.
Substituting these values into the formula above, we get:
kg of N mineralized/ha of soil = (60 mg N/kg of soil x 2 000 000 kg/ha)/1000
kg of N mineralized/ha of soil = 120 kg/ha
Therefore, 120 kg/ha of nitrogen is mineralized every year.
Part A Identify which sets of quantum numbers are valid for an electron. Each set is ordered (n, l, me, m.). Check all that apply. ▸ View Available Hint(s) 4,3,1,-1/2 2,3,1,1/2 3,2,1,-1 3,1,1,-1/2 O2,-1,1,-1/2) 3,3,-2,-1/2 2,1,1,1/2 4,3,-5,-1/2 1,1,0,1/2 3,2,-1,-1/2 2,1,-1,1/2 0,2,1,1/2
The valid sets of quantum numbers for an electron are: 2, 3, 1, 1/2 and 3, 2, 1, -1.
In quantum mechanics, electrons in an atom are described by four quantum numbers: the principal quantum number (n), the azimuthal quantum number (l), the magnetic quantum number (m), and the spin quantum number (ms). Each quantum number has specific rules and constraints.
To determine the valid sets of quantum numbers, we need to consider the following rules:
1. The principal quantum number (n) must be a positive integer (1, 2, 3, ...).
2. The azimuthal quantum number (l) can have values ranging from 0 to (n-1).
3. The magnetic quantum number (m) can have values ranging from -l to +l.
4. The spin quantum number (ms) represents the electron's spin and can only have two values: +1/2 or -1/2.
Checking each set of quantum numbers provided:
- 4, 3, 1, -1/2: This set is valid, as it satisfies the rules.
- 2, 3, 1, 1/2: This set is not valid, as the azimuthal quantum number (l) cannot be greater than the principal quantum number (n).
- 3, 2, 1, -1: This set is not valid, as the magnetic quantum number (m) cannot be greater than the azimuthal quantum number (l).
- 3, 1, 1, -1/2: This set is not valid, as the azimuthal quantum number (l) cannot be greater than the principal quantum number (n).
- O2, -1, 1, -1/2: This set is not valid, as O2 is not a valid value for the principal quantum number (n).
- 3, 3, -2, -1/2: This set is not valid, as the magnetic quantum number (m) cannot be greater than the azimuthal quantum number (l).
- 2, 1, 1, 1/2: This set is valid, as it satisfies the rules.
- 4, 3, -5, -1/2: This set is not valid, as the magnetic quantum number (m) cannot have an absolute value greater than the azimuthal quantum number (l).
- 1, 1, 0, 1/2: This set is valid, as it satisfies the rules.
- 3, 2, -1, -1/2: This set is valid, as it satisfies the rules.
- 2, 1, -1, 1/2: This set is not valid, as the magnetic quantum number (m) cannot be negative for l > 0.
- 0, 2, 1, 1/2: This set is not valid, as the principal quantum number (n) cannot be zero.
Based on the above analysis, the valid sets of quantum numbers for an electron are: 2, 3, 1, 1/2 and 3, 2, 1, -1.
Learn more about magnetic : brainly.com/question/2841288
#SPJ11
Calculate the thermal equilibrium electron and hole
concentration in silicon at T = 300 K for the case when the Fermi
energy level is 0.31 eV below the conduction band energy.
Eg=1.12eV
At thermal equilibrium in silicon at T = 300 K with the Fermi energy level 0.31 eV below the conduction band energy (Eg = 1.12 eV), the concentration of electrons and holes is determined by the intrinsic carrier concentration, which is approximately 2.4 x 10^19 carriers/cm^3.
The concentration of electrons and holes at thermal equilibrium in a semiconductor is determined by the intrinsic carrier concentration, which is a characteristic property of the material. In silicon at T = 300 K, the intrinsic carrier concentration (ni) is approximately 2.4 x 10^19 carriers/cm^3.
The position of the Fermi energy level (Ef) relative to the conduction and valence band energies determines the concentration of electrons and holes. In this case, the Fermi energy level is 0.31 eV below the conduction band energy. Given that the bandgap of silicon (Eg) is 1.12 eV, the valence band energy is 1.12 eV below the conduction band energy.
At thermal equilibrium, the concentration of electrons (n) and holes (p) is equal and can be approximated using the following equation:
n * p = ni^2
Since n = p, we can solve for either n or p. Substituting ni^2 for n * p, we get:
n^2 = ni^2
Taking the square root of both sides, we find:
n = p = ni
Therefore, at thermal equilibrium, the concentration of electrons and holes in silicon at T = 300 K, with the Fermi energy level 0.31 eV below the conduction band energy, is approximately 2.4 x 10^19 carriers/cm^3, which is the intrinsic carrier concentration of silicon.
Learn more about equilibrium : brainly.com/question/30694482
#SPJ11
How do the plants and photosynthestic bacteria produce sugars
from CO2 and H2O?
What is pentose phosphate pathway and what is its role in
metabolism?
Plants and photosynthetic bacteria produce sugars through the process of photosynthesis. They use energy from sunlight, along with carbon dioxide (CO2) and water (H2O), to produce glucose and oxygen.
Plants and photosynthetic bacteria utilize a process called photosynthesis to produce sugars from CO2 and H2O. Photosynthesis occurs in specialized structures called chloroplasts in plants and in the cell membrane or specialized structures like chromatophores in bacteria.
During photosynthesis, chlorophyll and other pigments capture light energy from the sun. This energy is then used to drive a series of chemical reactions. In the light-dependent reactions, light energy is converted into chemical energy in the form of ATP (adenosine triphosphate) and NADPH (nicotinamide adenine dinucleotide phosphate). These energy-rich molecules are then used in the light-independent reactions, also known as the Calvin cycle or C3 pathway.
In the Calvin cycle, CO2 and H2O are used to produce glucose and oxygen. The CO2 is fixed and converted into organic molecules through a series of enzymatic reactions. The energy from ATP and the reducing power from NADPH are utilized in these reactions to convert carbon atoms into carbohydrates, including glucose. This glucose serves as the primary source of energy and building blocks for the plant or bacteria.
The pentose phosphate pathway (PPP) is an alternative metabolic pathway that operates alongside glycolysis and the citric acid cycle in cellular metabolism. It plays a crucial role in the generation of energy and the synthesis of essential cellular components.
The primary function of the pentose phosphate pathway is the production of pentose sugars, such as ribose-5-phosphate, which are important building blocks for nucleotides, nucleic acids, and coenzymes. Additionally, the pathway generates NADPH, a reducing agent crucial for various cellular processes, including the synthesis of fatty acids, cholesterol, and other lipids, as well as detoxification reactions.
Learn more about photosynthetic : brainly.com/question/26561399
#SPJ11
Which example is an exothermic reaction?
4Fe (s) + 302 (g) + 6H2O (l) → 4Fe(OH)3 (s) + heat
H2O (s) + heat → H₂O (1)
NH4NO3 + heat → NH++ NO 4
heat+C6H12O6 (s) + H2O (l) →→ C6H12O6 (l) + H₂O (1)
Answer:
The example of an exothermic reaction is:
4Fe (s) + 3O2 (g) + 6H2O (l) → 4Fe(OH)3 (s) + heat
Explanation:
The reaction provided, 4Fe (s) + 3O2 (g) + 6H2O (l) → 4Fe(OH)3 (s) + heat, is an example of an exothermic reaction because it releases heat as a product.
In exothermic reactions, the overall energy of the reactants is higher than the energy of the products. During the reaction, bonds between atoms are broken, and new bonds are formed to create the products. In this particular reaction, iron (Fe) reacts with oxygen (O2) and water (H2O) to form iron(III) hydroxide (Fe(OH)3).
The formation of the Fe(OH)3 solid releases heat, indicating that energy is being given off to the surroundings. The release of heat suggests that the products have a lower energy state than the reactants. Therefore, this reaction is classified as exothermic.
It's worth noting that the other provided reactions do not indicate the release of heat as a product, making them either endothermic or not directly associated with heat transfer.
Feed the feed C7H16-C8H18 mixture at 250C 1 atm (bubble point 1120C specific heat of feed 243.615kl/kgmole-ok) into continuous tower distillation, if feed F-100 kgmole/h, its concentration XF-0.4, top
The feed for the continuous tower distillation consists of a mixture of C7H16 and C8H18 with a flow rate of 100 kmol/h and a concentration of 0.4. The feed temperature is 25°C and the pressure is 1 atm. The bubble point of the feed is 112°C, and the specific heat of the feed is 243.615 kJ/kgmol·K.
In continuous tower distillation, the feed is introduced into the tower and undergoes separation based on the differences in boiling points of the components. The lighter components with lower boiling points tend to concentrate towards the top of the tower, while the heavier components with higher boiling points collect at the bottom.
To carry out the distillation process effectively, it is important to understand the properties of the feed mixture. In this case, the feed consists of a mixture of C7H16 and C8H18. The flow rate of the feed is given as 100 kmol/h, and the concentration of the mixture is 0.4, indicating that C7H16 and C8H18 make up 40% of the total mixture.
The temperature of the feed is 25°C (250K), and the pressure is 1 atm. The bubble point of the feed, which is the temperature at which the first bubble of vapor is formed, is 112°C (1120K).
The specific heat of the feed is provided as 243.615 kJ/kgmol·K. This value represents the amount of heat required to raise the temperature of one kilogram of the feed mixture by one degree Kelvin.
The given information provides the necessary details for the feed composition, flow rate, temperature, pressure, bubble point, and specific heat of the feed mixture for continuous tower distillation. These parameters are essential for designing and operating the distillation process effectively to separate the components based on their boiling points.
To learn more about distillation , visit
brainly.com/question/7072845
#SPJ11