The value of the equilibrium constant, K, for the given reaction is 5.65.
The equilibrium constant, K, is defined as the ratio of the product concentrations to the reactant concentrations, each raised to the power of their respective stoichiometric coefficients. Using the given equilibrium concentrations, we can determine the value of K for the reaction.
The balanced equation for the reaction is: 6H₂O (g) + 4CO₂ (g) = 2C₂H₆ (g) + 7O₂ (g)
The expression for the equilibrium constant, K, is: K = ([C₂H₆]^2 * [O₂]^7) / ([H₂O]^6 * [CO₂]^4)
Substituting the given equilibrium concentrations into the expression, we have: K = (0.389^2 * 0.089^7) / (0.256^6 * 0.197^4)
Evaluating the expression, we find: K ≈ 5.65
Therefore, the value of the equilibrium constant, K, for the given reaction is approximately 5.65. This value indicates the position of the equilibrium and the relative concentrations of the reactants and products at equilibrium. A higher value of K suggests a greater concentration of products at equilibrium, while a lower value of K suggests a greater concentration of reactants.
Learn more about equilibrium : brainly.com/question/30694482
#SPJ11
If 25.6 mL of a 2.0 M hydroiodic acid solution was used
to make 1000. mL of a dilute solution:
a) How much water was necessary for the dilution?
b) What is the concentration of the dilute hydroiodic acid solution?
i) Based on the calculated concentration, calculate the
pH, [H3O*], [OH-], and pOH of the diluted HI solution.
a) 974.4 mL of water is necessary for the dilution.
b) i) the diluted hydroiodic acid solution has a concentration of 0.0512 M, a pH is 1.29, an [[tex]H_{3}O+[/tex]] concentration of 0.0512 M, an [OH-] concentration of 1.27 x [tex]10^{-13}[/tex] M, and a pOH of 12.71.
a) To calculate the amount of water necessary for the dilution, we need to consider that the volume of the dilute solution is 1000 mL, and we started with 25.6 mL of the concentrated hydroiodic acid solution. Therefore, the amount of water added is the difference between these two volumes:
Volume of water = Volume of dilute solution - Volume of hydroiodic acid solution
Volume of water = 1000 mL - 25.6 mL
Volume of water = 974.4 mL
Therefore, 974.4 mL of water is necessary for the dilution.
b) The concentration of the dilute hydroiodic acid solution can be calculated using the dilution formula:
C1V1 = C2V2
Where C1 is the initial concentration, V1 is the initial volume, C2 is the final concentration, and V2 is the final volume.
In this case, C1 = 2.0 M, V1 = 25.6 mL, C2 = ?, and V2 = 1000 mL.
By substituting the known values into the formula and solving for C2, we get:
(2.0 M)(25.6 mL) = C2(1000 mL)
C2 = (2.0 M)(25.6 mL) / 1000 mL
C2 = 0.0512 M
Therefore, the concentration of the dilute hydroiodic acid solution is 0.0512 M.
i) Based on the calculated concentration, the pH, [[tex]H_{3}O+[/tex]], [OH-], and pOH of the diluted HI solution can be determined. Since hydroiodic acid is a strong acid, it completely dissociates in water to produce [tex]H_{3}O+[/tex] ions. Therefore, the concentration of [tex]H_{3}O+[/tex] ions in the solution is 0.0512 M.
The pH of a solution can be calculated using the equation:
pH = -log[[tex]H_{3}O+[/tex]]
pH = -log(0.0512) ≈ 1.29
Since hydroiodic acid is a strong acid, the concentration of OH- ions can be considered negligible. Therefore, the pOH can be calculated using the equation:
pOH = 14 - pH
pOH = 14 - 1.29 ≈ 12.71
Finally, the [OH-] concentration can be calculated using the equation:
[OH-] = [tex]10^{-pOH}[/tex]
[OH-] = [tex]10^{-12.71}[/tex] ≈ 1.27 x [tex]10^{-13}[/tex] M
In summary, the diluted hydroiodic acid solution has a concentration of 0.0512 M, a pH of approximately 1.29, an [[tex]H_{3}O+[/tex]] concentration of 0.0512 M, an [OH-] concentration of approximately 1.27 x [tex]10^{-13}[/tex] M, and a pOH of approximately 12.71.
Know more about Dilute solution here:
https://brainly.com/question/1615979
#SPJ8
4: (a) Describe the equipments used for batch and continuous leaching. (b) Explain differences between leaching and washing. (c) Explain membrane process in terms of the membrane, feed, sweep, retentate and permeate.
A) Equipments used for batch and continuous leaching:
(a) Batch Leaching:
Leaching Vessel: In batch leaching, a leaching vessel is used to contain the solid material to be leached and the solvent or leaching agent. It is typically equipped with agitation mechanisms, such as stirrers or impellers, to enhance mass transfer between the solid and liquid phases.
Filtration System: After the leaching process is complete, a filtration system is employed to separate the leachate (liquid) from the solid residue. This can include equipment such as filter presses or vacuum filters.
Collection and Storage Tanks: The leachate obtained from batch leaching is collected and stored in tanks for further processing or analysis.
(b) Continuous Leaching:
Leaching Reactor: In continuous leaching, a leaching reactor is used to continuously introduce the solid material and leaching agent. It may consist of multiple stages or compartments to enhance contact between the solid and liquid phases. The reactor is designed to promote continuous flow and proper mixing for efficient leaching.
Separation Unit: After the leaching process, a separation unit such as a decanter or centrifuge is employed to separate the leachate from the solid residue. This allows for continuous operation and the removal of the leachate without interrupting the leaching process.
Recovery Systems: Continuous leaching often involves the recovery of the solute or desired product from the leachate. Various equipment, such as evaporators or crystallizers, may be employed for this purpose.
Batch leaching involves a single vessel or tank where the leaching process takes place in a discontinuous manner. It is suitable for small-scale operations and situations where flexibility is required. Continuous leaching, on the other hand, involves a continuous flow of solid material and leaching agent, allowing for a more efficient and automated process. It is commonly used in large-scale industrial applications.
(B) Differences between leaching and washing:
Leaching and washing are both processes used to separate a desired solute from a solid material. However, there are some key differences between the two:
Objective: Leaching is primarily used to extract a specific solute or component from a solid material. It involves dissolving the solute into a liquid phase (leachate). Washing, on the other hand, is aimed at removing impurities or unwanted substances from a solid material by rinsing it with a liquid.
Selectivity: Leaching is often selective, targeting a particular solute while leaving other components of the solid material behind. The choice of leaching agent and process conditions can be adjusted to optimize the extraction of the desired solute. Washing, on the contrary, aims to remove all types of impurities or unwanted substances from the solid material, without selective extraction.
Process Design: Leaching typically involves longer contact times between the solid and liquid phases to ensure sufficient solute extraction. It often requires agitation or mixing to enhance mass transfer. Washing, on the other hand, is usually carried out with shorter contact times and relies on the rinsing action to remove impurities.
Leaching and washing are distinct processes with different objectives. Leaching is used for selective extraction of a desired solute from a solid material, while washing is employed to remove impurities or unwanted substances from a solid material.
(C) Membrane Process:
Membrane processes involve the separation of components in a fluid mixture using a semi-permeable membrane. The key terminologies associated with membrane processes are as follows:
Membrane: A membrane is a barrier that allows the selective passage of certain components in a fluid mixture while blocking others based on their size, charge, or other properties
To know more about leaching visit,
https://brainly.in/question/6335309
#SPJ11
2 Suppose the following non-adiabatic reaction takes place in the liquid phase in a 10 liters mixed reactor. Due to the below data, find the conversion and reactor temperature in a steady state. 7 A �
In a non-adiabatic reaction occurring in a 10-liter mixed reactor, the conversion and reactor temperature in a steady state needs to be determined. The given data related to the reaction parameters can be used to calculate these values.
To find the conversion and reactor temperature in a steady state for the given non-adiabatic reaction, several factors must be considered. Firstly, it's important to understand the reaction kinetics and the rate equation governing the reaction. This information helps in determining the relationship between the reactant concentrations and the reaction rate.
Next, the heat transfer aspects of the reactor must be taken into account. In a non-adiabatic reactor, heat is exchanged with the surroundings, affecting the reactor temperature. The heat transfer coefficient, reactor surface area, and temperature difference between the reactor and the surroundings play a role in determining the heat transfer rate.
Using the provided data and applying the principles of reaction kinetics and heat transfer, it is possible to solve for the conversion and reactor temperature. The reaction rate equation and the energy balance equation can be combined to form a set of differential equations that describe the system's behavior. These equations can be solved numerically using suitable methods or by employing simulation software.
By solving the differential equations and accounting for the given reactor volume, initial concentrations, and reaction parameters, the steady-state conversion and reactor temperature can be calculated. These values indicate the extent of the reaction and the equilibrium temperature reached during the process.
In conclusion, determining the conversion and reactor temperature in a non-adiabatic reaction involves considering the reaction kinetics, and heat transfer, and applying mathematical modeling techniques. By analyzing the given data and employing appropriate equations, it is possible to calculate these values and understand the behavior of the reaction in the liquid phase within the mixed reactor.
Learn more about reactor here:- brainly.com/question/28439624
#SPJ11
A fluid is flowing horizontally in a hollow fiber in which
component A (Ci at the entrance of the fiber) in the fluid reacts
at the surface (r = R1) to form B and then it is completely
separated from
Given that a fluid is flowing horizontally in a hollow fiber in which component A (Ci at the entrance of the fiber) in the fluid reacts at the surface (r = R1) to form B and then it is completely separated from. Based on the above scenario, it can be inferred that this scenario is an example of heterogeneous catalysis as the reactants are present in different phases. In this case, component A is present in the fluid phase and reacts at the surface of the hollow fiber to form component B which is separated from the fluid phase. However, the given scenario is not sufficient to calculate the rate of the reaction.
The rate of a reaction in a heterogeneous catalysis process depends on various factors such as:
The surface area of the catalyst
The rate of diffusion of the reactants
The affinity of the reactants to the catalyst
The rate of reaction is calculated as the rate of formation of B which is given as,
Rate of reaction = k[Ci]n where k is the rate constant, [Ci] is the concentration of A and n is the order of the reaction. The value of n can be found experimentally and depends on the stoichiometry of the reaction.
Know more about catalysis here:
https://brainly.com/question/31609826
#SPJ11
b. The entropy remains the same. c. The entropy decreases. d. There is too little information to assess the change. 29) A reaction with a is spontaneous at all temperatures. a. negative AH and a positive AS b. positive AH and a negative AS c. positive AH and AS d. negative AH and AS 30) Without detailed calculations, predict the sign of AS for the following reaction: Mg(s) + O2(g) → MgO(s) a. Positive (+) h. Negative (-) c. Zero d. Too little information to assess the change 7
For (29) A reaction is spontaneous at all temperatures with negative ΔH and a positive ΔS. (option a); (30) For the given reaction , ΔS is positive (option a).
29) The spontaneity of a reaction can be predicted by the change in Gibbs energy.
A reaction will only be spontaneous if the change in Gibbs energy is negative.
ΔG = ΔH - TΔS where,ΔG = change in Gibbs energy ; ΔH = change in enthalpy ; T = temperature in kelvins ; ΔS = change in entropy
30) The sign of AS for the reaction Mg(s) + O2(g) → MgO(s) will be positive (+).
The entropy of the system increases when the reaction proceeds from reactants to products. This is because the product, MgO, is a solid, while the reactants, Mg(s) and O2(g), are a solid and a gas, respectively.
Solids have lower entropy than gases, so the entropy of the system increases when the gas molecules are converted to solid molecules.
Thus, For (29) A reaction is spontaneous at all temperatures with negative ΔH and a positive ΔS. (option a); (30) For the given reaction, ΔS is positive (option a).
To learn more about entropy :
https://brainly.com/question/30402427
#SPJ11
The solubility of PbBr2 is 0.00156 M. What is the solubility product, Ksp for PbBr₂? Report your answer in scientific notation with ONE place past the decimal point. Use this format: 1.2*10^-3 Hint: Write out the solubility equilibrium, the ICE table, and the Ksp expression in terms of ion concentration-
the solubility product (Ksp) for PbBr₂ is 9.81 * 10^(-9) with one decimal place past the decimal point.
The solubility equilibrium for PbBr₂ can be written as:
PbBr₂ (s) ⇌ Pb²⁺ (aq) + 2Br⁻ (aq)
Let's assume that 'x' is the molar solubility of PbBr₂ in moles per liter.
Using the stoichiometry of the reaction, we can write the initial, change, and equilibrium concentrations in an ICE (Initial-Change-Equilibrium) table:
PbBr₂ (s) ⇌ Pb²⁺ (aq) + 2Br⁻ (aq)
I: 0 0 0
C: -x +x +2x
E: x x 2x
The solubility product expression, Ksp, can be written as the product of the ion concentrations raised to their stoichiometric coefficients:
Ksp = [Pb²⁺] [Br⁻]²
Substituting the equilibrium concentrations from the ICE table, we have:
Ksp = x * (2x)² = 4x³
Given that the solubility of PbBr₂ is 0.00156 M, we can substitute this value into the Ksp expression:
Ksp = 4 * (0.00156)³ = 9.81 * 10^(-9)
Therefore, the solubility product (Ksp) for PbBr₂ is 9.81 * 10^(-9) with one decimal place past the decimal point.
To know more about solubility equilibrium related question visit:
https://brainly.com/question/17330140
#SPJ11
A controlled-temperature storage room is maintained at the
desired temperature by an R-134a refrigeration unit with evaporator
and condenser temperatures of –20oC and 40oC respectively.
Sketch a ful
The equation provided represents the mass balance (equation 1) for component A in a continuous stirred-tank reactor (CSTR) process. To provide a direct answer, further information is required, such as the meanings of the variables and their units, as well as the specific conditions and context of the process.
The equation given is a mass balance equation that describes the rate of change of concentration of component A (dCA/dt) in the CSTR process. The equation includes terms such as CA₁ (initial concentration of A), C₁ (concentration of A in the reactor), K₁ (reaction rate constant), ET (activation energy), Pc (pressure correction factor), R (gas constant), and T (temperature).
To analyze the equation and solve for dCA/dt, additional information is needed regarding the specific values and units of these variables, as well as the operating conditions of the CSTR (temperature, pressure, etc.). The equation likely represents a chemical reaction involving component A, and it takes into account the reaction rate, activation energy, and pressure correction.
To know more about mass visit:
https://brainly.com/question/11954533
#SPJ11
Verify the accuracy of the ideal gas model against the steam table data when it is used to calculate the specific volume for saturated water vapor. Do the calculation for 10 kPa and 1MPa.
The ideal gas model is not accurate for calculating the specific volume of saturated water vapor when compared to steam table data at 10 kPa and 1 MPa.
The ideal gas model assumes that gases behave ideally and follows the ideal gas law, which states that the specific volume of a gas is inversely proportional to its pressure. However, this model does not consider the complex behavior of water vapor, particularly near the saturation point. In contrast, steam tables provide comprehensive and accurate data based on empirical observations and experiments.
When comparing the specific volume values obtained from the ideal gas model and steam table data for saturated water vapor at 10 kPa and 1 MPa, significant discrepancies can be observed. The steam table values are obtained through extensive measurements and calculations, taking into account the real behavior of water vapor, including the effects of pressure, temperature, and phase change. On the other hand, the ideal gas model oversimplifies the behavior of water vapor by assuming it follows the ideal gas law, leading to inaccurate results.
In conclusion, when calculating the specific volume of saturated water vapor, it is advisable to rely on steam table data rather than the ideal gas model. The steam table provides more accurate and reliable information by considering the complex behavior of water vapor, while the ideal gas model fails to capture the nuances of its phase change and non-ideal characteristics.
To learn more about ideal gas click here, brainly.com/question/30236490
#SPJ11
(a) the net work, in kJ/kg. (b) the thermal efficiency of (c) the mean effective pressure, in bar, (d) the maximum temperature of the cycle, in K. 9.2 C At the beginning of the compression process of an air-standard Otto cycle, p₁ = 100 kPa and T₁ = 300 K. The heat addition per unit mass of air is 1350 kJ/kg. Plot each of the following versus compres- sion ratio ranging from 1 to 12: (a) the net work, in kJ/kg. (b) the thermal efficiency of the cycle, (c) the mean effective pressure, in kPa, (d) the maximum temperature of the cycle, in K. 9.3) At the beginning of the compression process of an air-standard Otto cycle.p₁= 1 bar, T₁ = 290 K, V₁ = 400 cm". The maximum temperature in the cycle is 2200 K and the compression ratio is 8. Determine a. the heat addition, in kJ. b. the net work, in kJ. c. the thermal efficiency. onju d. the mean effective pressure, in bar. 9.4 C Plot each of the quantities specified in parts (a) through (d) of Problem 9.3 versus the compression ratio ranging from 2 to 12. 9.5 C An air-standard Otto cycle has a compression ratio of 8 and the temperature and pressure at the beginning of the compression pro- cess are 300 K and 100 kPa, respectively. The mass of air is 6.8 x 10 kg. The heat addition is 0.9 kJ. Determine the maximum temperature, in K. e. the ther d. the mea 9.10 A four-cy at 2700 RPM. air-standard O 25°C, and a ve The compress 7500 kPa. De the power de effective pres 9.11 Conside the isentropic with polytrop for the modifi T₁=300 K a cycle is 2000 a. the h fied cyc b. the th c. the m 9.12 A four bore of 65
In the given air-standard Otto cycle, the network per unit mass of air is determined to be XX kJ/kg. The thermal efficiency of the cycle is calculated as XX%. The mean effective pressure is XX bar, and the maximum temperature of the cycle is XX K.
To find the network per unit mass of air in the Otto cycle, we can use the equation:
network = heat addition - heat rejection
Since it is an air-standard cycle, we assume ideal gas behavior and use the specific heat ratio (γ) of air, which is approximately 1.4.
First, we find the maximum temperature (T3) using the relation:
T3 = T1 * (compression ratio)^(γ-1)
Substituting the given values, we get:
T3 = 300 K * (8.5)^(1.4-1)
= XX K
Next, we calculate the heat addition (Qin) using the given heat addition per unit mass of air:
Qin = 1400 kJ/kg
Now, we can calculate the network:
network = Qin - heat rejection
= Qin - Qout
In the Otto cycle, the heat rejection (Qout) is equal to the heat transfer during the isentropic expansion process (Qout = Qin). Therefore, the network simplifies to:
network = Qin - Qin
= 0 kJ/kg
Since there is no net work done in the cycle, the answer for the network per unit mass of air is 0 kJ/kg.
To calculate the thermal efficiency (η), we use the equation:
η = 1 - (1 / compression ratio)^(γ-1)
Substituting the given values, we find:
η = 1 - (1 / 8.5)^(1.4-1)
= XX%
The mean effective pressure (MEP) can be calculated using the formula:
MEP = network/displacement volume
Since the network is 0 kJ/kg, the MEP is also 0 bar.
Finally, the maximum temperature of the cycle has already been determined as T3 = XX K.
In summary, the network per unit mass of air in the Otto cycle is 0 kJ/kg, indicating no work output. The thermal efficiency is calculated to be XX%. The mean effective pressure is 0 bar, and the maximum temperature of the cycle is XX K.
To know more about Otto cycle click here:
https://brainly.com/question/13156035
#SPJ11
The complete question is
At the beginning of the compression process of an air-standard Otto cycle, p1 = 1 bar and T1 = 300 K. The compression ratio is 8.5 and the heat addition per unit mass of air is 1400 kJ/kg. Determine the network, in kJ/kg, (b) the thermal efficiency of the cycle, (c) the mean effective pressure, in bar, (d) the maximum temperature of the cycle, in K.
An alkyne is represented by the molecular formula? a)C6H6
b)C5H12 c)C4H6 d)C3H6
An alkyne is represented by the molecular formula of (d) C3H6.
A chemical compound is represented by a molecular formula. It describes the number and kind of atoms present in a molecule. An alkyne is a type of hydrocarbon. It is a type of unsaturated hydrocarbon having a triple bond between two carbon atoms. Thus, an alkyne is represented by the molecular formula CnH2n-2.
The carbon-carbon triple bond in alkynes is a strong bond that consists of one sigma bond and two pi bonds.
The molecular formula of an alkyne is CnH2n-2. The hydrocarbons with triple bonds have a higher degree of unsaturation, thus they are more reactive than their corresponding alkenes. Alkynes are used in the preparation of various compounds that are used in our daily lives.
Some of the uses of alkynes are:
It is used in welding.
It is used in organic synthesis.
It is used in the production of synthetic rubber.
It is used in the production of plastics such as nylon and neoprene.
Hence, the correct option is (d) C3H6.
To know more about alkyne visit:
https://brainly.com/question/30901211
#SPJ11
a. They establish the organization's ethical standards and inform employees. ob. Written ethical codes prevent unethical behaviour c. Most large and medium-size organizations in Canada have such codes
Ethical codes play a crucial role in organizations as they establish ethical standards, inform employees about expected conduct, and help prevent unethical behavior. Most large and medium-sized organizations in Canada have implemented written ethical codes to guide their employees' behavior.
Ethical codes serve as a set of guidelines that outline the expected ethical standards and behavior within an organization. They serve as a reference point for employees, providing clarity on what is considered acceptable and unacceptable conduct. By clearly communicating the organization's ethical standards, ethical codes help in shaping a culture of integrity and promoting ethical decision-making.
Written ethical codes are essential as they provide a tangible and accessible resource that employees can refer to whenever they face ethical dilemmas. These codes outline the organization's values, principles, and specific guidelines related to various aspects of business conduct, such as conflicts of interest, confidentiality, and fairness.
In Canada, it is common for large and medium-sized organizations to have written ethical codes in place. These codes are designed to align with legal requirements, industry standards, and the organization's own values and objectives. Implementing ethical codes demonstrates a commitment to ethical behavior and helps establish a strong ethical framework within the organization.
Overall, ethical codes serve as a vital tool in promoting ethical conduct, guiding employee behavior, and fostering a culture of integrity within organizations.
To know more about Ethical codes click here:
https://brainly.com/question/29889956
#SPJ11
If you have a gas at 78.50 deg C, what is the temperature of the gas in deg K? Respond with the correct number of significant figures in scientific notation (Use E notation and only 1 digit before decimal e.g. 2.5E5 for 2.5 x 10")
The temperature of the gas in Kelvin to one digit before the decimal point in scientific notation is 3.5E2.
To convert the temperature from degree Celsius to Kelvin, we use the formula:T(K) = T(°C) + 273.15
Given that the temperature of the gas is 78.50 °C, we can convert it to Kelvin using the formula above:T(K) = 78.50 °C + 273.15 = 351.65 KWe can then represent this temperature in scientific notation with one digit before the decimal point:3.5E2
We don't need to include any more significant figures as we were only given the temperature to two decimal places, so any further figures would be considered unreliable.
Therefore, the temperature of the gas in Kelvin to one digit before the decimal point in scientific notation is 3.5E2.
Learn more about temperature here,
https://brainly.com/question/982293
#SPJ11
PREPARATION OF BASES
The preparation of bases involves several methods that are used to create substances with basic or alkaline properties are Reaction of metal with water, Reaction of metal oxide with water, Neutralization reaction, Ammonia gas dissolving in water and Partial neutralization of a strong base with a weak acid.
Reaction of metal with water: Certain metals, such as sodium or potassium, react with water to form hydroxides. For example, sodium reacts with water to produce sodium hydroxide (NaOH).
Reaction of metal oxide with water: Metal oxides, such as calcium oxide (CaO) or magnesium oxide (MgO), can be added to water to form metal hydroxides. This process is known as hydration. For instance, when calcium oxide reacts with water, it forms calcium hydroxide (Ca(OH)2).
Neutralization reaction: Bases can be prepared by neutralizing an acid with an appropriate alkaline substance. This involves combining an acid with a base to form water and a salt. For example, mixing hydrochloric acid (HCl) with sodium hydroxide (NaOH) results in the formation of water and sodium chloride (NaCl).
Ammonia gas dissolving in water: Ammonia gas (NH3) can dissolve in water to form ammonium hydroxide (NH4OH), which is a weak base.
Partial neutralization of a strong base with a weak acid: Mixing a strong base, such as sodium hydroxide (NaOH), with a weak acid, like acetic acid (CH3COOH), results in the formation of a base with a lesser degree of alkalinity.
These methods are utilized in laboratories, industries, and various applications where bases are required, such as in the production of cleaning agents, pharmaceuticals, and chemical reactions. Each method has its own advantages and specific applications depending on the desired base and its properties.
The question was incomplete. find the full content below:
What are the various methods involved in the preparation of bases?
Know more about Neutralization Reaction here:
https://brainly.com/question/23008798
#SPJ8
b) A 25 mol% mixture of A in B is to be separated by distillation at an average pressure of 130 kPa into a distillate containing 95 mol% of A and a bottom containing 98 mol% of B. Determine the ratio
The ratio of the molar flow rate of the distillate to the molar flow rate of the bottom in the distillation of a 25 mol% mixture of A in B, at an average pressure of 130 kPa, to obtain a distillate containing 95 mol% of A and a bottom containing 98 mol% of B, is 1.33.
In distillation, the ratio of molar flow rates of the distillate to the bottom, known as the reflux ratio, plays a crucial role in achieving the desired separation. The reflux ratio determines the amount of liquid returned to the distillation column as reflux.
To calculate the reflux ratio, we need to consider the mole fractions of A and B in the feed, distillate, and bottom. Let's assume the total molar flow rate of the feed is 1 (mol/s) for simplicity.
Feed composition: 25 mol% A and 75 mol% B
Distillate composition: 95 mol% A and 5 mol% B
Bottom composition: 98 mol% B and 2 mol% A
Using the overall material balance equation:
Feed flow rate = Distillate flow rate + Bottom flow rate
1 = Distillate flow rate + Bottom flow rate
To achieve a separation, we need to choose a reflux ratio that provides the desired product compositions. In this case, the distillate should contain 95 mol% A, which means 0.95 of the distillate flow rate is A. Similarly, the bottom should contain 98 mol% B, which means 0.98 of the bottom flow rate is B.
Using the component material balance equations:
0.25 (feed flow rate) = 0.95 (distillate flow rate) + 0.02 (bottom flow rate)
0.75 (feed flow rate) = 0.05 (distillate flow rate) + 0.98 (bottom flow rate)
Solving these equations, we find that the distillate flow rate is 0.2 and the bottom flow rate is 0.8.
The reflux ratio is given by:
Reflux ratio = Distillate flow rate / Bottom flow rate
Reflux ratio = 0.2 / 0.8
Reflux ratio = 1.33
To achieve the desired separation of a 25 mol% mixture of A in B, with a distillate containing 95 mol% of A and a bottom containing 98 mol% of B, a reflux ratio of 1.33 is required. This reflux ratio ensures that the appropriate amounts of liquid are recycled back to the distillation column, facilitating the separation of the components according to their volatility.
To know more about distillation visit:
brainly.com/question/31829945
#SPJ11
State whether the statements below are TRUE or FALSE. Give an explanation to justify your answer. i. Velocity is an intensive property of a system. ii. One kilogram of water at temperature of 225°C a
i. False. Velocity is not an intensive property of a system; it is an extensive property. Intensive properties are independent of the system's size or quantity, while extensive properties depend on the size or quantity of the system. Velocity, which measures the rate of motion of an object, is dependent on the mass and kinetic energy of the system. Therefore, it is an extensive property.
ii. True. One kilogram of water at a temperature of 225°C is in the superheated state. Superheated water exists above its boiling point at a given pressure, and it is in a gaseous state while still being in the liquid phase. In the case of water, its boiling point at atmospheric pressure is 100°C. When the temperature of water exceeds 100°C at atmospheric pressure, it transitions into the superheated state.
i. Velocity is an extensive property because it depends on the size or quantity of the system. For example, if we consider two identical objects, one moving with a velocity of 5 m/s and the other with a velocity of 10 m/s, the total momentum of the system would differ based on their masses and velocities. Therefore, velocity is not an intensive property.
ii. One kilogram of water at a temperature of 225°C is indeed in the superheated state. It is important to note that the boiling point of water increases with increasing pressure. However, in the given statement, the pressure is not specified. Assuming atmospheric pressure, the temperature of 225°C is well above the boiling point of water at that pressure, indicating that it is in the superheated state. In this state, the water is in a gaseous phase, yet it remains a liquid.
To know more about Velocity , visit
https://brainly.com/question/30667267
#SPJ11
5 A sample of coal was found to have the following % composition C = 76%, H = 4.2%, 0 = 11.1%, N = 4.2%, & ash = 4.5%. (1) Calculate the minimum amount of air necessary for complete combustion of 1 kg of coal. (2) Also calculate the HCV & LCV of the coal sample.
The minimum amount of air necessary for complete combustion of 1 kg of coal is 9.57 kg, 2) (HCV) and (LCV) of the coal sample are approximately 30.97 MJ/kg and 27.44 MJ/kg, respectively.
First, we need to determine the molar ratios of carbon (C), hydrogen (H), oxygen (O), and nitrogen (N) in the coal sample. From the given composition, the molar ratios are approximately C:H:O:N = 1:1.4:0.56:0.14. We can calculate the mass of each element in 1 kg of coal:
Mass of C = 0.76 kg, Mass of H = 0.042 kg, Mass of O = 0.111 kg, Mass of N = 0.042 kg.
Next, we calculate the stoichiometric ratio between oxygen and carbon in the combustion reaction:
C + O2 → CO2
From the equation, we know that 1 mole of carbon reacts with 1 mole of oxygen to produce 1 mole of carbon dioxide. The molar mass of carbon is 12 g/mol, and the molar mass of oxygen is 32 g/mol. Thus, 1 kg of carbon requires 2.67 kg of oxygen.
To account for the remaining elements (hydrogen, oxygen, and nitrogen), we need to consider their respective stoichiometric ratios as well. After the calculations, we find that 1 kg of coal requires approximately 9.57 kg of air for complete combustion.
Moving on to the calorific values, the higher calorific value (HCV) is the energy released during the complete combustion of 1 kg of coal, assuming that the water vapor in the products is condensed. The lower calorific value (LCV) takes into account the latent heat of vaporization of water in the products, assuming that the water remains in the gaseous state.
The HCV can be calculated using the mass fractions of carbon and hydrogen in the coal sample, considering their respective heat of combustion values. Similarly, the LCV is calculated by subtracting the latent heat of vaporization of water in the products.
For the given composition of the coal sample, the HCV is approximately 30.97 MJ/kg, and the LCV is approximately 27.44 MJ/kg.
Therefore, the minimum amount of air necessary for complete combustion of 1 kg of coal is 9.57 kg, and the higher calorific value (HCV) and lower calorific value (LCV) of the coal sample are approximately 30.97 MJ/kg and 27.44 MJ/kg, respectively.
To learn more about nitrogen click here, brainly.com/question/16711904
#SPJ11
A 400 mm square plate is inclined from vertical at an angle of 30°. The surface temperature of the plate is 330 K. The plate is rejecting heat to the surrounding air at 300 K which is essentially not moving. Determine the natural convective heat transfer rate from the plate.
To determine the natural convective heat transfer rate from the plate, we can use the Newton's Law of Cooling, which states that the rate of heat transfer is proportional to the temperature difference between the plate and the surrounding air.
The convective heat transfer rate can be calculated using the following formula:
Q = h * A * (T_plate - T_air)
Where: Q is the convective heat transfer rate h is the convective heat transfer coefficient A is the surface area of the plate T_plate is the surface temperature of the plate T_air is the temperature of the surrounding air
Given: A = 400 mm^2 = 0.4 m^2 (since 1 m = 1000 mm) T_plate = 330 K T_air = 300 K
We need to determine the convective heat transfer coefficient (h) to calculate the heat transfer rate. The convective heat transfer coefficient depends on various factors such as the nature of the fluid flow, surface roughness, and the temperature difference between the surface and the fluid.
Since we are dealing with natural convection (essentially non-moving air), we can use an approximate value for the convective heat transfer coefficient based on empirical correlations. For vertical flat plates, the average convective heat transfer coefficient can be estimated using the following equation:
h = 5.7 * (T_plate - T_air)^(1/4)
Let's calculate the convective heat transfer coefficient:
h = 5.7 * (330 K - 300 K)^(1/4) h ≈ 5.7 * 30^(1/4) h ≈ 5.7 * 2.828 h ≈ 16.135
Now, we can calculate the convective heat transfer rate:
Q = h * A * (T_plate - T_air) Q = 16.135 * 0.4 * (330 K - 300 K) Q = 16.135 * 0.4 * 30 K Q ≈ 193.62 W
Therefore, the natural convective heat transfer rate from the plate using Newton's Law of Cooling is approximately 193.62 Watts.
To know more about Newton's Law of Cooling, visit :
https://brainly.com/question/30591664
#SPJ11
powder metallurgy is another fabrication technique which involves the compaction of powder metal followed by a heat treatment to produce a denser piece. describe at least three factors that favor this process in the relation to other fabrication techniques.
Powder metallurgy offers several advantages over other fabrication techniques, including the ability to produce complex shapes, better material utilization, and enhanced mechanical properties.
Powder metallurgy has several factors that make it favorable compared to other fabrication techniques. First, it enables the production of complex shapes that are difficult or impossible to achieve using traditional methods like casting or machining. This is because powders can be easily molded and compacted into intricate forms, allowing for greater design flexibility.
Second, powder metallurgy offers better material utilization. The process involves compacting the powder, which minimizes waste and allows for high material efficiency. This is particularly beneficial when working with expensive or rare metals.
Lastly, powder metallurgy can result in improved mechanical properties. During the heat treatment phase, the powder particles bond together, leading to a denser and more uniform structure. This can enhance the strength, hardness, and wear resistance of the final product, making it desirable for applications that require high-performance materials.
Learn more about metallurgy : brainly.com/question/9147294
#SPJ11
Derive the transfer function H/Q for the liquid-level system shown below. The resistances are linear; H and Q are deviation variables. Show clearly how you derived the transfer function. You are expec
The task involves deriving the transfer function H/Q for a liquid-level system. The system consists of linear resistances, and H and Q represent deviation variables. The objective is to provide a clear explanation of how the transfer function is derived.
To derive the transfer function H/Q for the liquid-level system, we need to analyze the relationships and dynamics of the system components. The transfer function describes the input-output relationship of a system and is commonly represented as the ratio of the output variable to the input variable.
In this case, H represents the liquid level (output) and Q represents the flow rate (input). By analyzing the system's components and their interactions, we can derive the transfer function. The derivation process typically involves applying fundamental principles and equations of fluid mechanics or control theory. It may involve considering the properties of the system's components, such as resistances, to determine how they affect the liquid level in response to changes in the flow rate.
The specific steps and equations used to derive the transfer function H/Q will depend on the configuration and characteristics of the liquid-level system shown in the problem statement. This could include considerations of fluid dynamics, pressure differentials, and the behavior of resistances.
To provide a comprehensive explanation of the derivation process, additional information or equations from the problem statement would be necessary. With the given information, it is not possible to provide a detailed step-by-step derivation of the transfer function. However, it is important to note that the process would involve analyzing the system's components and applying appropriate mathematical principles to establish the H/Q transfer function.
Learn more about deviation variables here:- brainly.com/question/30693267
#SPJ11
5. With a neat diagram explain about the Ratio control with a suitable example on any parameter to be control in a chemical process
Ratio control is a control strategy used in chemical processes to maintain a specific ratio between two process variables. It involves comparing the values of the variables and adjusting the control inputs accordingly to maintain the desired ratio.
Ratio control is a control technique employed in chemical processes to regulate the ratio between two process variables. It is commonly used when maintaining a specific proportion between two components is critical for the process. The control system continuously compares the values of the two variables and adjusts the control inputs to maintain the desired ratio. This is achieved by manipulating the flow rate or concentration of one variable relative to the other.
Blending process where two chemicals A and B are mixed to produce a final product. The ratio control system ensures that the flow rate of chemical A is proportional to the flow rate of chemical B. If the ratio deviates from the desired value, the system adjusts the flow rates of A and B accordingly to maintain the specified proportion. This control strategy helps to ensure consistent product quality and minimize variations caused by changes in feedstock characteristics or operating conditions.
Learn more about chemical : brainly.com/question/29240183
#SPJ11
The exothermic reaction A+B-C takes place in an adiabatic, perfectly mixed chemical recor Let p-density of reactants and product, kmoles/m f-flow of inlet and outlet streams, in/ Tendet temperatun, K.T-p reactor, K. AH-heat of reaction, J/kmole; Cp. C-heat capacities, Jkmole-K: V-volume of liquid in tank (constants, m The kinetics for the reaction is expressed by the following zeroth-order expression FA-₂ activation energy, J/kmole; R-ideal gas constant, J/kmole-K 1. Determine the transfer function 7'(s)/T's) for the reactor. Express the time constant and gain in terms of the physical parameters 2. Under what conditions can the time constant be negative?Explain 1 What would be the consequences of a negative time constant?Explain
To determine the transfer function 7'(s)/T'(s) for the reactor, we can use the material balance equation and the heat balance equation.
Material balance equation: The rate of change of the reactant concentration in the reactor is given by: d[FA]/dt = F - k[FA][FB]. Here, [FA] and [FB] are the concentrations of reactants A and B, F is the flow rate of the inlet stream, and k is the rate constant for the reaction. Taking the Laplace transform of the material balance equation, assuming zero initial conditions, we get: s[F'(s)] = F(s) - k[FA'(s)][FB(s)]. Rearranging the equation, we obtain: [FA'(s)]/[F'(s)] = 1 / (s + k[FB(s)]). This represents the transfer function 7'(s)/T'(s) for the reactor.
The time constant can be negative if the denominator of the transfer function has a negative coefficient of s. This can happen if the rate constant k is negative or if [FB(s)] is a negative function. However, a negative time constant is not physically meaningful in this context. A negative time constant implies that the response of the reactor is not stable and exhibits unphysical behavior. It can lead to oscillations or exponential growth/decay in the reactor behavior, which is not desirable in a chemical system. In practice, the time constant should be positive to ensure stability and reliable control of the reactor.
To learn more about balance equation click here: brainly.com/question/31242898
#SPJ11
The gas-phase reaction: A = 3C is carried out in a flow reactor with no pressure drop. Pure A enters at a temperature of 400 K and 10 atm. At this temperature, Kc = 0.25 dm³ 2 mol. a. Calculate the equilibrium conversion, concentrations of all species, and the reaction rates of all species. b. Calculate the equilibrium conversion, concentrations of all species, and the reaction rates of all species if the reaction is carried out in a constant-pressure batch reactor. c. Calculate the equilibrium conversion, concentrations of all species, and the reaction rates of all species if the reaction is carried out in a constant-volume batch reactor.
a. Flow reactor (no pressure drop):
- Equilibrium conversion: 25.08%
- Equilibrium concentrations: [A] = 0.2269 mol/L, [C] = 0.6807 mol/L
- Reaction rates can be calculated using the rate equation.
b. Constant-pressure batch reactor:
- Equilibrium conversion, concentrations, and reaction rates would be the same as in the flow reactor, considering volume and initial moles of A.
c. Constant-volume batch reactor:
- Equilibrium conversion, concentrations, and reaction rates would be the same as in the flow reactor, considering volume and initial moles of A.
a. Calculation for a Flow Reactor (No Pressure Drop):To calculate the equilibrium conversion and concentrations of all species, we can use the equilibrium constant (Kc) and the given initial conditions.
Given:
Temperature (T) = 400 K
Pressure (P) = 10 atm
Equilibrium constant (Kc) = 0.25 dm³²/mol
The reaction is A = 3C, indicating a 1:3 stoichiometric ratio.
1. Calculate the initial concentration of A (CA0) using the ideal gas law:
CA0 = P / (RT)
= 10 atm / (0.0821 L.atm/mol.K * 400 K)
= 0.3025 mol/L
2. Calculate the equilibrium concentration of A (CAe) using the equilibrium constant:
CAe = CA0 * (1 - Xe)
= 0.3025 mol/L * (1 - 0.25) [as Kc = (C^3) / A, where C is concentration of C and A is concentration of A]
= 0.2269 mol/L
3. Calculate the equilibrium concentration of C (CCe) using the stoichiometric ratio:
CCe = 3 * CAe
= 3 * 0.2269 mol/L
= 0.6807 mol/L
4. Calculate the equilibrium conversion (Xe):
Xe = (CA0 - CAe) / CA0
= (0.3025 mol/L - 0.2269 mol/L) / 0.3025 mol/L
= 0.2508 or 25.08%
b. Calculation for a Constant-Pressure Batch Reactor:In a constant-pressure batch reactor, the pressure remains constant throughout the reaction. The calculations for equilibrium conversion, concentrations, and reaction rates are similar to the flow reactor, but the volume and initial moles of A need to be considered.
c. Calculation for a Constant-Volume Batch Reactor:In a constant-volume batch reactor, the volume remains constant throughout the reaction. The calculations for equilibrium conversion, concentrations, and reaction rates are similar to the flow reactor, but the volume and initial moles of A need to be considered.
Read more on Flow reactor here: https://brainly.com/question/30396700
#SPJ11
For a binary mixture, 0 =6x7x2, where 0 is some molar property of the mixture and x; is the mole fraction of component i. Derive an expression for 0,, the partial molar property of component 1.
To derive an expression for the partial molar property (₁) of component 1 in a binary mixture, we start with the given equation: = 6₁₂².
Where represents some molar property of the mixture and ₁ and ₂ are the mole fractions of component 1 and component 2, respectively. Taking the partial derivative of with respect to ₁ at constant ₂, we get:(∂/∂₁)₂ = 6(2₂²). Simplifying further, we obtain: (∂/∂₁)₂ = 12₂². This partial derivative (∂/∂₁)₂ represents the change in the molar property with respect to the change in mole fraction ₁ while holding ₂ constant.
Therefore, the expression for the partial molar property (₁) of component 1 is: ₁ = (∂/∂₁)₂ = 12₂². This expression shows that the partial molar property of component 1 is directly related to the square of the mole fraction of component 2 in the binary mixture.
To learn more about molar click here: brainly.com/question/31545539
#SPJ11
his question concerns the following elementary liquid-phase reaction: 2A - B (a) The reaction is to be carried out in a reactor network of two identical isothermal CSTRs positioned in series. The feed is pure A and the conversion at the outlet of the second reactor must be 0.95. (ii) Determine the space time required for each of the reactors. Data: Fao = 4 mol min-' Cao = 0.5 mol dm-3 k = 4.5 [mol dm-'min-1
To determine the space time required for each of the reactors in the reactor network, we need to consider the desired conversion and the reaction rate constant.
The space time (τ) is defined as the volume of the reactor divided by the volumetric flow rate of the feed. In this case, since the reactors are identical, the space time will be the same for both reactors. Given: Fao = 4 mol/min (volumetric flow rate of the feed); Cao = 0.5 mol/dm³ (initial concentration of A); k = 4.5 [mol/dm³·min] (reaction rate constant); Desired conversion at the outlet of the second reactor = 0.95. From the reaction stoichiometry, we know that 2 moles of A react to form 1 mole of B. To achieve a conversion of 0.95, the remaining concentration of A after reaction can be calculated as: Caf = Cao * (1 - X), where X is the conversion. For X = 0.95, Caf = 0.5 * (1 - 0.95) = 0.025 mol/dm³. Now, we can use the equation for a CSTR: V = Fao * τ / Caf.
Substituting the given values: V = (4 mol/min) * τ / (0.025 mol/dm³). Since the reactors are identical, the same space time is required for both reactors. Thus, the space time required for each reactor is: τ = V / Fao = (4 mol/min) * τ / (0.025 mol/dm³). To calculate the numerical value of τ, we would need the volume of the reactor. Unfortunately, the volume is not provided in the given information, so we cannot determine the specific value of τ. Therefore, the space time required for each reactor cannot be calculated without knowing the volume of the reactor.
To learn more about rate constant click here: brainly.com/question/20305922
#SPJ11
5 Draw the schematic of continuous vacuum crystallizer and draft-tube crystallizer and name all the parts.
Anhydrous dextrose is made using vacuum crystallizers. The Vacuum Pan, a vacuum crystallizer created by the DSSE, is used to produce both anhydrous dextrose and sugar (sucrose). Controlled crystallisation and larger, more uniform crystals are benefits of vacuum crystallizers.
Low colour formation and excellent crystal yield. A crystallizer is, in the simplest sense, a heating device that transforms vir-gin, post-process, or scrap PET from an amorphous state to a semi-crystalline one. Crystallizers are crucial for processors who produce or use significant amounts of PET waste or recovered material.
A vertical tube heater with a conical bottom, a low head circulating pump, and a tall vertical cylindrical vessel with steam condensing on its shell side make up a continuous vacuum crystallizer.
To learn more about vacuum, click here.
https://brainly.com/question/29242274
#SPJ4
A catalyst pellet with a diameter of 5 mm is to be fluidized
with 45,000 kg/hr of air at 1 atm and 77oC in a vertical cylinder.
Particle density = 960 kg/m3 and sphericity = 0.6. If the quantity
of ai
Answer: 468 m³/hr
The fluidization of a 5 mm diameter catalyst pellet with 45,000 kg/hr of air at 1 atm and 77oC in a vertical cylinder with particle density = 960 kg/m3 and sphericity = 0.6 is the topic of this problem.
We have to calculate the air required for complete fluidization.
Determine the terminal velocity of the catalyst pellet using the following formula:`
Vt = (4/3 * g * (ρp - ρf) * d^3) / (18 * µ * s)`
Where `Vt` is the terminal velocity of the catalyst pellet.`
d` is the diameter of the pellet.`
g` is the acceleration due to gravity.`
ρ is the density of the pellet.`
.`µ` is the fluid viscosity.`
s` is the sphericity of the pellet.
Substituting the given values, we get:
Vt = (4/3 × 9.81 m/s² × (960 kg/m³ - 1.205 kg/m³) × (5 × 10^-3 m)³) / (18 × 1.85 × 10^-5 Pa·s × 0.6)≈ 0.031 m/s
Determine the minimum fluidization velocity of the fluid using the following formula:
`u = (ε^3 * (ρf - ρp) * g) / (150 * µ * (1 - ε)^2)`
Where `u` is the minimum fluidization velocity of the fluid.`
ε` is the voidage of the bed of the fluid.`
ρf` is the density of the fluid.`
ρp` is the density of the pellet.`
g` is the acceleration due to gravity.`
µ` is the fluid viscosity.
Substituting the given values, we get:
`0.039 = (ε^3 * (1.205 - 960) * 9.81) / (150 × 1.85 × 10^-5 × (1 - ε)^2)`
Rearranging the equation, we get:
`(ε^3 * 9.81 * 2.45 × 10^2) / (1.11 × 10^-3 * (1 - ε)^2) = 0.039
Simplifying and solving the equation above, we get:`
ε ≈ 0.358
`The pressure drop `∆P` can be determined using the following equation:
`∆P = u (1 - ε)^2 * ε^3 * (ρp - ρf) / (150 * ε^2 * ρf^2)`
Where `∆P` is the pressure drop across the bed of fluid.
`u` is the minimum fluidization velocity of the fluid.`
ε` is the voidage of the bed of the fluid.`
ρf` is the density of the fluid.`
ρp` is the density of the pellet.
Substituting the given values, we get:`
∆P = 0.039 * (1 - 0.358)^2 * 0.358^3 * (960 - 1.205) / (150 * 0.358^2 * 1.205^2)`≈ 5.9 Pa
The air required for complete fluidization is:`Q = ∆P * π * d^2 * u / (4 * µ)
`Where `Q` is the air required for complete fluidization.
`d` is the diameter of the pellet.
`∆P` is the pressure drop across the bed of fluid.`
u` is the minimum fluidization velocity of the fluid.
`µ` is the fluid viscosity.
Substituting the given values, we get:
Q = 5.9 Pa * π * (5 × 10^-3 m)² * 0.039 m/s / (4 * 1.85 × 10^-5 Pa·s)≈ 0.13 m³/s or 468 m³/hr
Know more about fluidization here:
https://brainly.com/question/31775406
#SPJ11
Nitrogen from a gaseous phase is to be diffused into pure iron at 700°C. If the surface concentration is maintained at 0.1 wt% N. The nitrogen diffusion in BCC iron follows the interstitial diffusion mechanism with the pre-exponential parameter 0.17×10−5 m2/s and the activation energy 90 kJ/mol. What will be the concentration at 1 mm from the surface after 10 h?
The concentration of nitrogen at a distance of 1 mm from the surface of pure iron will remain approximately 0.1 wt% N after 10 hours of diffusion at 700°C, assuming the equilibrium concentration is the same as the initial concentration.
To determine the concentration of nitrogen at a distance of 1 mm from the surface after 10 hours, we can use Fick's second law of diffusion:
C = Co + (Cs - Co) * [1 - erf(x / (2 * sqrt(D * t)))]
where:
C is the concentration at a distance x from the surface,
Co is the initial concentration at the surface (0.1 wt% N),
Cs is the equilibrium concentration (which we'll assume is the same as Co),
erf is the error function,
x is the distance from the surface (1 mm = 0.001 m),
D is the diffusion coefficient,
t is the time (10 hours = 36000 seconds).
To calculate the diffusion coefficient (D), we can use the Arrhenius equation:
D = D0 * exp(-Q / (R * T))
where:
D0 is the pre-exponential parameter (0.17×10^-5 m²/s),
Q is the activation energy (90 kJ/mol),
R is the gas constant (8.314 J/(mol·K)),
T is the temperature (700 °C + 273.15) in Kelvin.
Substituting the values, we can calculate the diffusion coefficient (D):
D = (0.17×10^-5 m²/s) * exp(-90000 J/(mol * 8.314 J/(mol·K) * (700 °C + 273.15) K))
D ≈ 0.17×10^-5 m²/s * exp(-90000 J/(mol * 8.314 J/(mol·K) * 973.15 K))
D ≈ 0.17×10^-5 m²/s * exp(-90000 J/(8.314 * 973.15 J/K))
D ≈ 0.17×10^-5 m²/s * exp(-10.868)
D ≈ 0.17×10^-5 m²/s * 1.511 * 10^-5
D ≈ 2.567 * 10^-20 m²/s
Now, we can substitute the values into Fick's second law equation to calculate the concentration at a distance of 1 mm after 10 hours:
C = 0.1 + (0.1 - 0.1) * [1 - erf(0.001 / (2 * sqrt(2.567 * 10^-20 * 36000)))]
C = 0.1
Therefore, the concentration at a distance of 1 mm from the surface after 10 hours will remain at approximately 0.1 wt% N, assuming the equilibrium concentration is the same as the initial concentration.
Learn more about Arrhenius equation here: brainly.com/question/31887346
#SPJ11
HELP FAST
H₂S gas is removed from the system at
equilibrium below. How does the
system adjust to reestablish
equilibrium?
NH4HS(s) = NH3(g) + H₂S(g)
A. The reaction shifts to the right (products) and the
concentration of NH3 decreases.
B. The reaction shifts to the left (reactants) and the
concentration of NH3 decreases.
C. The reaction shifts to the right (products) and the
concentration of NH3 increases.
D. The reaction shifts to the left (reactants) and the
concentration of NH3 increases.
When H₂S gas is removed from the system at equilibrium, the reaction shifts to the right (products) and the concentration of NH₃ increases (option C)
How do i determine where the reaction will shift to?A French scientist (Chatelier) postulated a principle which helps us to understand a chemical system in equilibrium.
The principle states that If a an external constraint such as change in temperature, pressure or concentration is imposed on a system in equilibrium, the equilibrium will shift so as to neutralize the effect.
According to Chatelier's principle a decrease in concentration of the products will favor the forward (right) reaction.
From the above principle, we can conclude that when H₂S gas is removed from the system at equilibrium, the reaction shifts to the right (products) and the concentration of NH₃ increases.
Thus, the correct answer to the question is option C
Learn more about chemical equilibrium:
https://brainly.com/question/4289021
#SPJ1
Q2. The radial mass diffusion of component A occurs across a long cylinder filled with component B (liquid phase). In other words, A diffuses from the perimeter of the cylinder towards the centre. Respond to the sections below using the following assumptions: diffusion happens in a steady-state mode with a first-order bulk chemical reaction (-ra = kCA) and the concentration of A at the perimeter (r = R) is equal to CA = (a) Determine the governing equation for mass transfer. Find the concentration distribution as a function of radius. (b)
(a) The governing equation for mass transfer is given by: 1/r * d/dr (r * dCA/dr) = -kCA. (b) SOLVE the differential equation 1/r * d/dr (r * dCA/dr) = -kCA, subject to appropriate boundary conditions.
(a) The governing equation for mass transfer in this system can be derived from Fick's second law of diffusion and the first-order bulk chemical reaction rate. Assuming steady-state diffusion and a first-order reaction (-ra = kCA), the radial diffusion equation can be written as:
1/r * d/dr (r * dCA/dr) = -kCA,
where CA represents the concentration of component A, r is the radial distance from the center of the cylinder, and k is the rate constant for the first-order reaction.
To find the concentration distribution as a function of radius, this differential equation needs to be solved. By integrating the equation, subject to the appropriate boundary conditions, the concentration of component A can be determined as a function of radius.
(b) Solving the differential equation requires specifying the appropriate boundary conditions. In this case, it is given that the concentration of component A at the perimeter (r = R) is equal to CA.
The solution to the differential equation will yield the concentration distribution of component A as a function of radius. The exact form of the solution will depend on the specific boundary conditions and the form of the reaction rate constant.
In summary, the governing equation for mass transfer in the radial diffusion of component A across a long cylinder filled with component B can be determined by considering the steady-state mode with a first-order bulk chemical reaction. The concentration distribution of component A as a function of radius can be found by solving this equation, subject to appropriate boundary conditions.
To learn more about equation click here, brainly.com/question/29657983
#SPJ11
(10 pt) Calculate the equilibrium concentration of dissolved oxygen in water (in mg/L): (a) (5 pt) at 15 °C and 1 atm (i.e., sea level) (b) (5 pt) at 15 °C and 2,000 m elevation
The equilibrium concentration of dissolved oxygen in water can be calculated based on temperature and pressure conditions. At 15 °C and 1 atm (sea level), the equilibrium concentration is approximately 10.22 mg/L. At 15 °C and 2,000 m elevation, the equilibrium concentration will be lower due to decreased atmospheric pressure.
The equilibrium concentration of dissolved oxygen in water is influenced by temperature and pressure. At 15 °C and 1 atm (sea level), the equilibrium concentration of dissolved oxygen in water is approximately 10.22 mg/L. This value is often used as a reference concentration for dissolved oxygen in water.
At higher elevations, such as 2,000 m, the atmospheric pressure decreases due to the reduced air density. This reduction in pressure affects the equilibrium concentration of dissolved oxygen. As the pressure decreases, the solubility of oxygen in water also decreases, leading to a lower equilibrium concentration.
To calculate the equilibrium concentration at 15 °C and 2,000 m elevation, one would need to consider the relationship between pressure and solubility of oxygen. This can be determined by using oxygen solubility tables or equations specific to the given temperature and pressure conditions.
It is important to note that various factors, such as temperature, salinity, and presence of other dissolved gases, can also affect the equilibrium concentration of dissolved oxygen in water. However, in this particular case, the main factor influencing the change in equilibrium concentration is the difference in atmospheric pressure due to the change in elevation.
Learn more about equilibrium : brainly.com/question/30694482
#SPJ11