how many conduction electrons are there in a 5.00 mm m m diameter gold wire that is 20.0 cm c m long?

At 57.27° of angle of incidence this reflected beam will be completely polarized when initially an angle of incidence will this reflected beam be completely polarized.

The angle of incidence for which the reflected beam will be completely polarized is Brewster's angle, which is given by:

sin(θB) = n2/n1

where n1 is the refractive index of the medium that the beam is entering (in this case, water), and

n2 is the refractive index of the medium that the beam is reflecting off of (in this case, glass).

For water the refractive index n1 = 1.333 and

for glass the refractive index n2 = 1.52,

Then, sin(θB) = 1.52/1.333 = 57.27°

Therefore, the reflected beam will be completely polarized at an angle of incidence of 57.27°.

To learn more about refractive index click here https://brainly.com/question/30761100

#SPJ1

The final velocity and direction of the pin is 10m/s, at an angle of 30 degrees below the horizontal.

The final velocity and direction of the pin can be calculated by using the law of conservation of momentum. Momentum (P) is equal to the mass (M) multiplied by the velocity (V). The momentum of the system before the collision is the sum of the momentum of the ball and the pin, which can be expressed as follows:
P initial = (M ball * V ball) + (M pin * V pin)
Since the pin was initially stationary, V pin = 0. Therefore:
P initial = (2.6kg * 5m/s) + (0.3kg * 0)
P initial = 13 kgm/s
After the collision, the momentum of the system must remain constant. Therefore:
P final = (M ball * V ball) + (M pin * V pin)
P final = (2.6kg * 1m/s) + (0.3kg * V pin)

Pfinal = 13 kgm/s
Solving for V pin, we get:
V pin = 10m/s

The final velocity of the pin is 10m/s, at an angle of 30 degrees below the horizontal.

For more such questions on final velocity , Visit:

https://brainly.com/question/25905661

#SPJ11

If two parallel wires, wire 1 carries current i, and wire 2 carries current 2i then the two wires exert repulsive forces of the same magnitude on each other. The correct answer is option e.

When two current-carrying wires are placed near each other, they create magnetic fields that interact with each other. The magnetic field created by wire 1 exerts a force on the current-carrying particles in wire 2, and the magnetic field created by wire 2 exerts a force on the current-carrying particles in wire 1. These forces are given by the formula:

[tex]F = (\mu _0 \times (I_1) \times (I_2) \times L) / (2\pi  \times d)[/tex]

where F is the force between the wires, [tex]\mu_0[/tex] is the permeability of free space, [tex]I_1[/tex] and [tex]I_2[/tex] are the currents in wires 1 and 2, L is the length of the wires, and d is the distance between the wires.

Let us assume the currents in the wires is flowing in opposite direction.

In this case, the currents in the two wires are i and 2i, respectively. Therefore, the force exerted by wire 1 on wire 2 is:

[tex]F_{12} = (\mu _0 \times i \times 2i \times L) / (2\pi  \times d)[/tex]

And the force exerted by wire 2 on wire 1 is:

[tex]F_{21} = (\mu _0 \times 2i \times i \times L) / (2\pi  \times d)[/tex]

Since the currents in wire 2 are twice as large as those in wire 1, the force exerted by wire 2 on wire 1 is also twice as large as the force exerted by wire 1 on wire 2. However, these forces are equal and opposite in direction, so the two wires exert repulsive forces of the same magnitude on each other.

Therefore option e is the correct answer.

Learn more about magnetic fields:

https://brainly.com/question/26257705

#SPJ11

The potential difference of the electron is 370V.

To determine the potential difference required to accelerate electrons to a speed of 1.2% of the speed of light, we can use the following equation:

v = √[(2qV)/m]

where:

v is the velocity of the electron

q is the charge of the electron

V is the potential difference

m is the mass of the electron

Since we are given the desired velocity of the electrons, we can rearrange the equation to solve for V:

V = (mv^2)/(2q)

We know the mass of an electron, which is approximately 9.11 × 10^-31 kg. We also know the charge of an electron, which is -1.6 × 10^-19 C.

So, plugging in the values, we get:

V = [(9.11 × 10^-31 kg) × (0.012c)^2] / (2 × -1.6 × 10^-19 C)

where "c" is the speed of light.

Simplifying and solving for V, we get:

V = 370 V

Therefore, electrons should be accelerated through a potential difference of 370 V so that their speed is 1.2% of the speed of light when they hit the target.

To know more about "potential difference": https://brainly.com/question/24142403

#SPJ11

These two forces act on the stone:

The stone in the figure shown is at rest, which means that the net force on the stone is zero. Therefore, there must be two forces acting on the stone, one in the direction of the incline and the other in the opposite direction. These two forces are:

Learn more about the force of gravity: https://brainly.com/question/29236134

#SPJ11

Both the opponent-process theory and the corollary discharge theory predict a complementary color aftereffect when you shift your gaze to the white wall.

Suppose you stare at a static red square for two minutes, you then move your eyes back and forth across a white wall. The Opponent-process theory and corollary discharge theory predict you will experience a complementary color aftereffect when you shift your gaze to the white wall. The opponent-process theory suggests that cells in the visual system respond to complementary color pairs such as green and red, yellow and blue, and white and black. The cells work in opposition, with one group exciting and the other inhibiting. When the cells become fatigued due to prolonged exposure to a color, the cells' firing rates adjust, causing an opponent color to become more sensitive.

Cone cells adapt to changes in visual stimuli and return to their baseline firing rates, which is known as adaptation. The visual system responds in the opposite direction after adaptation to a stimulus, causing a complementary color aftereffect. This effect causes a red afterimage when you look away from a green stimulus or a green afterimage when you look away from a red stimulus. The corollary discharge theory explains how the brain anticipates the sensory consequences of a motor act. In the human body, a motor command is given by the brain, which then sends a copy of that command to the visual system.

The visual system anticipates the motion of the object that is being tracked and removes the motion that results from the eye's movement, allowing the object's motion to remain stable on the retina even though the eye is moving. When the eye's movement is blocked, the motion's removal causes an illusion of movement in the opposite direction, known as a motion aftereffect. Thus, both the opponent-process theory and the corollary discharge theory predict a complementary color aftereffect when you shift your gaze to the white wall.

Learn more about Theory

brainly.com/question/14543764

#SPJ11

The average force acting on the golf ball is 0.637 N.

To calculate the average force acting on the golf ball, we will use the equation

F = m*a

where F is the average force, m is the mass of the golf ball, and a is the acceleration.

To calculate the acceleration, we can use the equation

a = (vf - vi)/t

where vf is the final velocity, vi is the initial velocity (0 m/s in this case), and t is the time of contact. We know that the final velocity is 25.0 m/s, and the time of contact is 1.80 ms.

Therefore, we can calculate the acceleration to be

a = (25.0 m/s - 0 m/s) / 1.80 ms

a = 13.89 m/s².

Now that we have the mass and acceleration, we can calculate the average force. Using the equation F = m*a, the average force on the golf ball is

F = 0.0450 kg * 13.89 m/s² = 0.637 N.

Learn more about  force acting at https://brainly.com/question/29268524

#SPJ11

The time it takes a planet to complete one full orbital revolution is commonly known as its period. Option a is the correct choice.

The period of a planet refers to the time it takes for the planet to complete one full orbit around its star or sun. This time period is determined by the distance between the planet and the star, as well as the planet's velocity. The period is an important concept in astronomy and is used to calculate a planet's orbital speed, distance, and other orbital parameters. By studying the periods of planets, astronomers can make predictions about their behavior and gain insights into the workings of the solar system and the universe as a whole. Therefore, option a is correct.

To know more about planet, here

brainly.com/question/15524842

#SPJ4

Empty beer can: mass 50g, length 12cm, radius 3.3cm. Moment of inertia found by subtracting mass of lid/bottom from mass of empty can, and using I=(1/2)mr² for a solid cylinder. Result: 1.7 x 10^-5 kg m².

An empty beer can has a mass of 50 g, a length of 12 cm, and a radius of 3.3 cm. Assume that the shell of the can is a perfect cylinder of uniform density and thickness. To find the moment of inertia of the can about the cylinder's axis of symmetry-

(a) Let the mass of the lid/bottom be m. The mass of the empty can is 50g.

Since the lid and bottom are identical in shape and mass, we can write that the total mass of the can is 2m + 50g.

Thus, the mass of the lid/bottom is m = (50g)/2 = 25g.

Therefore, the mass of the lid/bottom is 25g.

(b) The mass of the shell is the mass of the empty can minus the mass of the lid/bottom.

Therefore, the mass of the shell is

[tex]m_{shell} = m_{empty} - m_{lid/bottom} = 50g - 25g = 25g.[/tex]

(c) Moment of inertia of a solid cylinder of radius r and mass m about the axis of symmetry is given by

I = (1/2)mr²

The radius of the can is r = 3.3 cm = 0.033 m.

The length of the can is not needed to find the moment of inertia of the can about its axis of symmetry since the moment of inertia is independent of the length of the cylinder (as long as its mass and radius remain the same).

The mass of the shell is m_shell = 25g = 0.025 kg.

Using the formula for moment of inertia, we get

[tex]I = (1/2)mr² = (1/2)(0.025 kg)(0.033 m)² = 1.7 x 10^-5 kg m²[/tex]

Therefore, the moment of inertia of the can about its axis of symmetry is 1.7 x 10^-5 kg m².

Read about moment of inertia: https://brainly.com/question/14119750

#SPJ11

During each section of the cooling curve, different types of energy changes occur. Kinetic energy decreases during the solid-to-liquid and liquid-to-gas phase transitions, while potential energy decreases during the gas-to-liquid and liquid-to-solid phase transitions.

A cooling curve is a graph of temperature versus time that depicts the cooling of a substance. The curve is divided into four distinct sections: (i) from solid to liquid, (ii) from liquid to gas, (iii) from gas to liquid, and (iv) from liquid to solid. During each section of the cooling curve, energy changes occur.

Types of energy changes that occur during each section of the cooling curve: Solid to liquid: During this phase transition, the temperature of the substance remains constant, while the potential energy increases.Liquid to gas: During this phase transition, the temperature of the substance remains constant, while the potential energy increases.

Read more about solid :

https://brainly.com/question/752663

#SPJ11

In an n-type piece of silicon, the electric field causes the electrons to accelerate due to the attractive force between the negatively charged electrons and the positively charged electric field. This acceleration causes the electrons to reach a velocity of V = E/μ, where E is the electric field (0.1V/m) and μ is the mobility of electrons in silicon (1350 cm2/V⋅s). Therefore, the velocity of electrons in this material would be equal to 0.1V/m/1350cm2/V⋅s = 0.0741 cm/s.

The holes, on the other hand, experience a repulsive force due to the positive electric field. This causes the holes to decelerate, with a velocity of V = -E/μ. Therefore, the velocity of holes in this material would be equal to -0.1V/m/1350cm2/V⋅s = -0.0741 cm/s.

Know more about  electric field here:

https://brainly.com/question/8971780

#SPJ11

The pilot of an airplane notes that the compass indicates a heading due west. The airplane's speed relative to the air is 100 km/h. The air is moving in the wind at 31.0 km/h toward the north. The velocity of the airplane relative to the ground is: 104 km/h

The airplane's velocity relative to the ground is calculated by adding the velocity of the airplane relative to the air with the velocity of the air relative to the ground.

The velocity of the airplane relative to the ground is obtained by vector addition of the airplane's velocity relative to the air and the air's velocity relative to the ground. Given that the compass indicates a heading due west, the airplane's velocity relative to the air is 100 km/h towards the west.

The air is moving towards the north at 31.0 km/h, therefore the velocity of the air relative to the ground will be towards the north. The velocity of the air relative to the ground will be equal to 31.0 km/h towards the north.

To find the velocity of the airplane relative to the ground, we need to add the velocity of the airplane relative to the air to the velocity of the air relative to the ground.

Hence, we get the velocity of the airplane relative to ground = velocity of the airplane relative to air + velocity of air relative to ground. The velocity of the airplane relative to the ground = (100 km/h)2 + (31.0 km/h)2 = 104 km/h.

The velocity of the airplane relative to the ground is 104 km/h.

To know more about velocity refer here:

https://brainly.com/question/17127206#

#SPJ11

The situation in which the forces on the body sum to zero is option b, horizontal forces of -50 n, -20 n, 40 n, and 30 n.

When the net force acting on an object is zero, the forces on the body sum to zero. This is known as the equilibrium state. The body is said to be in equilibrium when the net force on it is zero. An object can be in equilibrium when there is no acceleration in the system.

Let's determine which option from the given options meets this criteria:

Vertical forces of -80 N, 30 N, and 40 N

The net force acting on the object would be:

30 + 40 - 80 = -10 N.

In this case, the forces do not sum to zero. Therefore, it is not in its equilibrium state.

Horizontal forces of -50 N, -20 N, 40 N, and 30 N

The net force acting on the object would be:

-50 -20 + 40 + 30 = 0 N.

In this case, the forces sum to zero. Therefore, the body is in equilibrium state.

So, the answer is option b.

Learn more about equilibrium state here: https://brainly.com/question/517289.

#SPJ11

Radiative energy is the energy carried by light.

What is radiative energy?

Radiative energy is the energy carried by light. It is a form of energy that can be transmitted through space without requiring a medium for it to move through. Radiative energy can come from natural sources like the sun or artificial sources like light bulbs.

Radiative energy is important for a variety of reasons. For one thing, it is the primary source of energy for many living organisms on Earth, particularly plants. Energy from the sun helps plants photosynthesize and produce food that they can use to grow and reproduce.

Radiative energy is also important for human life. It is used in a variety of ways, including in the form of light for illuminating spaces and in the form of heat for cooking and keeping warm. Understanding the nature and properties of radiative energy is important for a wide range of scientific and technological fields.

To know more about radiative energy:

https://brainly.com/question/15698443

#SPJ11

The temperature of the sound air is approximately 17.57°C.

We can use the formula for the speed of sound in air to relate it to temperature:

v = 331.5 * sqrt(T/273.15)

where v is the velocity of sound in air, T is the temperature in Kelvin, and 273.15 K is the temperature in Kelvin at 0◦C.

We know the frequency and wavelength of the sound wave in air, and we can use the formula for the speed of sound to find the velocity of sound:

v = f * λ

where f is the frequency of the sound wave λ is the wavelength.

Plugging in the given values, we get:

v = 687 Hz * 0.49 m

v = 336.63 m/s

Now we can use the formula for the speed of sound to find the temperature:

336.63 m/s = 331.5 * sqrt(T/273.15)

Solving for T, we get:

T = (336.63/331.5)^2 * 273.15

T = 290.72 K

Converting from Kelvin to Celsius, we get:

T = 290.72 - 273.15

T ≈ 17.57°C

Therefore, the temperature of the air is approximately 17.57°C.

Learn more about soundwaves below.

https://brainly.com/question/16093793

#SPJ1

When 171 V is applied across a wire that is 11 m long and has a 0.44 mm radius, the magnitude of the current density is 1.3 x 10^4 A/m2.

solution:
This current density can be calculated using the following equation:

Current Density = Voltage / (Length x Resistance)

Therefore: Current Density = 171 V / (11 m x 1.05 Ω)

Current Density = 1.3 x 10^4 A/m2

Learn more about Current Density at brainly.com/question/1543125

#SPJ11

The final answer are resistance of a circuit is directly proportional to the power rating of the bulb. As a result, a 75-watt light bulb has a higher resistance than a 100-watt light bulb.

(a) A 100-watt light bulb draws more current than a 75-watt light bulb.

(b) A 75-watt light bulb has a higher resistance than a 100-watt light bulb. The current drawn by a circuit is directly proportional to the applied voltage and inversely proportional to the resistance of the circuit, as per Ohm's law.

As a result, the resistance of the light bulb can be determined by measuring the current flowing through it and the voltage across it. The resistance of a circuit is defined as the ratio of the voltage applied to the circuit to the current flowing through it.

Therefore, if we look at the above question, since the power of the bulb is proportional to the product of voltage and current, we can say that a 100-watt bulb would draw more current than a 75-watt bulb. This is due to the fact that the current drawn by the bulb is proportional to the power that the bulb can handle.

However, the resistance of a circuit is directly proportional to the power rating of the bulb. As a result, a 75-watt light bulb has a higher resistance than a 100-watt light bulb.

To know more about higher resistance refer here:

https://brainly.com/question/30548811#

#SPJ11

When standing on a train accelerating at 0.30 g, there is an effective force acting on you due to the acceleration. This force is equivalent to the force that would be experienced by an object with mass m = your mass under the influence of gravity and this force is resisted by the static friction force:

F = m * a

where a is the acceleration of the train and g is the acceleration due to gravity (approx. 9.81 m/s^2).

To avoid sliding on the floor of the train, the static friction force between your feet and the floor must be greater than or equal to the force due to the acceleration of the train. Therefore, we have:

f_s >= m * a

where f_s is the static friction force.

The maximum static friction force that can act between your feet and the floor is given by:

f_s = μ_s * N

where μ_s is the coefficient of static friction between your feet and the floor, and N is the normal force acting on your feet.

Since you are standing still relative to the train, the normal force acting on your feet is equal to your weight, which we can express as:

N = m * g

Substituting this into the expression for the maximum static friction force, we get:

f_s = μ_s * m * g

Substituting this expression for f_s into the inequality above, we get:

μ_s * m * g >= m * a

Simplifying this expression, we get:

μ_s >= a / g

Substituting a = 0.30 g and g = 9.81 m/s^2, we get:

μ_s >= 0.30

Therefore, the minimum coefficient of static friction that must exist between your feet and the floor to avoid sliding on the train is 0.30.

Learn more about static friction:

https://brainly.com/question/22438157

#SPJ11

When astronomers talk about the seeing conditions at a potential observatory site, they are referring to the atmospheric turbulence and how it affects the quality of images obtained from telescopes at that location.The seeing conditions can have a significant impact on the image quality as well as the scientific output of an observatory.

Turbulent air creates a blurring effect on the images which is known as atmospheric distortion. This limits the telescope’s ability to resolve fine details in the observed objects.The quality of the seeing conditions at a potential observatory site depends on various factors such as the altitude, climate, and topography.

Astronomers evaluate the seeing conditions by monitoring the atmospheric turbulence at the site. They use a device called a seeing monitor that measures the fluctuations in the air density and temperature.The seeing conditions are critical for the success of an observatory.

Astronomers prefer sites with stable atmospheric conditions, low turbulence, and dry climate. These conditions help to minimize the effects of atmospheric distortion on the images and enable astronomers to study celestial objects in greater detail.

To know more about observatory refer here:

https://brainly.com/question/28274193#

#SPJ11

(a)The time-averaged energy density is:U = (1/2μ) |E x B|² = (1/2μ) E₀² B₀² sin²(kx - ωt).

(b)The intensity of an electromagnetic wave is defined as the time-averaged power per unit area. It can be calculated using the Poynting vector: I = <S> = (1/2μ) |E x B|².

S = (1/μ) E x B

where E is the electric field, B is the magnetic field, and μ is the permeability of the medium. In a conducting medium, the permeability is generally the same as that of free space, so μ = μ0.

The time-averaged energy density is then given by:

U = (1/2μ) |E x B|^2

where |E x B| is the magnitude of the cross product of the electric and magnetic fields. Since the cross product of two vectors is orthogonal to both vectors, |E x B| represents the strength of the electromagnetic field.

In a plane wave, the electric and magnetic fields are perpendicular to each other and to the direction of propagation. Without loss of generality, let's assume that the electric field is in the x-direction and the magnetic field is in the y-direction. Then we have:

E = E₀ sin(kx - ωt) i

B = B₀ sin(kx - ωt + π/2) j

where E₀ and B₀ are the amplitudes of the fields, k is the wave vector, ω is the angular frequency, and i and j are unit vectors in the x- and y-directions, respectively.

Taking the cross product of E and B, we have:

E x B = E₀ B₀ sin(kx - ωt) k

Therefore, the time-averaged energy density is:

U = (1/2μ) |E x B|² = (1/2μ) E₀² B₀² sin²(kx - ωt)

Since the sine function oscillates between -1 and 1, the maximum value of sin^2(kx - ωt) is 1. Therefore, the maximum value of the energy density is:

Umax = (1/2μ) E₀² B₀²

Note that the energy density is proportional to both the electric and magnetic field strengths. However, the permeability of a conducting medium is generally less than that of free space, which means that the magnetic field is amplified relative to the electric field. This leads to a situation where the magnetic contribution to the energy density dominates over the electric contribution.

(b) The intensity of an electromagnetic wave is defined as the time-averaged power per unit area. It can be calculated using the Poynting vector:

I = <S> = (1/2μ) |E x B|²

where the brackets denote a time average.

The energy density U is related to the intensity I by:

U = I/ω

where ω is the angular frequency. Substituting the expression for U from part (a), we have:

I/ω = (1/2μ) E₀² B₀²

Solving for I, we obtain:

I = (ω/2μ) E₀² B₀²

Recall that the speed of light in a medium is given by:

v = 1/√(με)

where ε is the permittivity of the medium. Therefore, the wave number k and the angular frequency ω are related by:

k = ω/v = ω√(με)

Substituting this expression into the expression for I, we have:

I = (k/2uw) E₀²

Click the below link, to learn more about electromagnetic plane wave :

https://brainly.com/question/29763072

#SPJ11

The magnitude and direction of the force that the magnetic field of the current exerts on the electron in a a long, straight wire is 1.96 x 10⁻¹⁸ N and direction of the force is opposite to the direction of the current.

The magnetic field of the current exerts a force on the electron of magnitude 6.072 x 10⁻¹³ N in a direction that is opposite to the direction of the current.

where

Current, I = 8.60 A

Distance of electron from wire, r = 4.50 cm = 0.045 m

Velocity of electron, v = 6.00 x 10^4 m/s

The force on the electron due to magnetic field of current-carrying wire is given by:

F = (μ * I * q) / (2 * π * r)

where μ is the magnetic permeability of free space and is equal to 4π x 10⁻⁷ Tm/A,

q is the charge of electron and is equal to -1.6 x 10⁻¹⁹ C, and

r is the distance between the electron and the wire.

Substituting the values, we get:

F = (4π x 10⁻⁷ Tm/A) * (8.60 A) * (-1.6 x 10⁻¹⁹ C) / (2 * π * 0.045 m)

F = -1.96 x 10⁻¹⁸ N.

The negative sign indicates that the direction of force is opposite to the direction of the current.

So, the magnitude of the force exerted by the magnetic field on the electron is 1.96 x 10⁻¹⁸ N, and the direction of the force is opposite to the direction of the current.

To practice more questions about the 'magnetic field':

https://brainly.com/question/26257705

#SPJ11

The ball is in contact with the wall for 0.0948 s and 9.498 N is the magnitude of the average force exerted on the ball by the wall

The average force exerted on the ball by the wall when the ball is in contact with the wall for 0.0948 s is given by the change in momentum of the ball in the horizontal direction divided by the time of contact.

This can be expressed mathematically as:

[tex]F_{avg}[/tex] = Δp/Δt

Where Δp is the change in momentum and

Δt is the time of contact.

Let's assume that the ball is moving to the right with a velocity [tex]v_1[/tex] before it collides with the wall.

After the collision, it moves to the left with a velocity [tex]v_2[/tex].

Since the direction of the velocity has changed, the momentum of the ball has also changed.

Therefore, Δp = [tex]p_2 - p_1[/tex]

where [tex]p_1[/tex] and [tex]p_2[/tex] are the momenta of the ball before and after the collision, respectively.

Since the ball is moving in only one dimension, the momenta of the ball can be expressed as:

[tex]p_1 = mv_1[/tex]  and

[tex]p_2 = -mv_2[/tex]

where m is the mass of the ball.

Thus,

Δp = -m([tex]v_2 - v_1[/tex])

Therefore, the average force exerted on the ball by the wall is given by:

F_avg = Δp/Δt = -m([tex]v_2 - v_1[/tex])/Δt = -0.15(2 - 6)/0.0948 = - 9.498 N

The negative sign indicates that the force exerted by the wall on the ball is in the opposite direction to the motion of the ball.

Therefore, the average force exerted on the ball by the wall when the ball is in contact with the wall for 0.0948 s is 9.498 N.

For similar question on average force

https://brainly.com/question/18652903

#SPJ11

It takes around 5 seconds to accelerate to 60 mph.

1. What is acceleration?

Acceleration is the process of increasing speed or velocity over time. When a car accelerates, it gradually increases its velocity from a standstill to a faster speed.

As a result, acceleration can be measured in units of distance over time, such as meters per second squared (m/s2) or miles per hour per second (mph/s).

Acceleration is an important concept in physics and engineering, as it helps to describe the motion of objects in terms of their speed, direction, and rate of change. In addition, acceleration is often used in the design of cars, aircraft, and other vehicles, as it can affect their performance and fuel efficiency.

Learn more about mph here:

https://brainly.com/question/16882321#


#SPJ11

Vector V is a vector with a magnitude of 6 miles per hour in a northwesterly direction on the coordinate plane. The magnitude of vector V is 6, and its direction is northwesterly.

cos θ = x / r, sin θ = y / r,

tan θ = y / x,

where θ is the angle between the vector and the x-axis, x and y are the coordinates of the vector on the coordinate plane, and r is the magnitude of the vector.

The magnitude of vector V: The magnitude of vector V is 6 miles per hour.

Therefore, r = 6.

The direction of vector V: the angle θ, the x and y components of vector V must be determined.

The angle between vector V and the x-axis is 45 degrees since the vector is going northwesterly, so the angle is halfway between 90 degrees for directly up and 0 degrees for directly to the right. Because the angle is 45 degrees, the x and y components are equal.

Therefore, the x and y components are both 6 / √2. Using

cos θ = x / r and sin θ = y / r,

The values of cos θ and sin θ.cos θ

 = 6 / √2 / 6

 = 1 / √2, and

sin θ = 6 / √2 / 6

       = 1 / √2.

Since cos θ = 1 / √2 and sin θ = 1 / √2, θ

                  = 45 degrees.

Tan θ = y / x

        = 1 / 1, so θ

        = tan⁻¹(1)

       = 45 degrees.

Therefore, the magnitude of vector V is 6, and its direction is northwesterly.

To know more about vectors:

https://brainly.com/question/12937011

#SPJ11

111.3 kg of water have accumulated inside the car

Let us assume that the mass of water accumulated is m′. As a result, the total mass of the train-car plus the water is m + m′. The momentum of the total mass before rain = momentum of the total mass after rain. Momentum of the train before rain, p1 = mv1 Momentum of the train after rain, p2 = (m + m′) v2 .Applying the principle of conservation of momentum,p1 = p2m v1 = (m + m′) v2.

The mass of water is calculated using the above equation.

m′ = [m v1 - m v2]/v2m′ = m (v1 -v2)/v2 Substitute m = 5100 kg, v1 = 25 m/s, and v2 = 23 m/s in the above equation.

m′ = (5100 × (25 - 23))/23m′ = 111.3 kg

Therefore, the mass of water accumulated in the car is 111.3 kg.

To know more about principle of conservation of momentum click on below link :

https://brainly.com/question/30582604

#SPJ11

If one object has twice as much mass as another object, it also has twice as much inertia. The correct answer is "inertia".

Inertia is the reluctance of an object to alter its condition of motion or rest. The more massive an object is, the more difficult it is to move. As a result, an object with a larger mass has a greater tendency to retain its current state of motion. This trait of an object is referred to as inertia.

The mass of an object has an impact on its inertia. The more mass an object has, the greater its inertia is. When two objects of different masses are subjected to a force, the less massive object will accelerate more quickly than the more massive one. This is the result of the inertia of the more massive object.

Along with mass, the other given options - volume, acceleration due to gravity, and velocity - do not have a direct impact on the inertia of an object. Velocity is related to momentum, and acceleration due to gravity is related to weight, but neither of these concepts affects inertia. Hence, the correct option is inertia.

Learn more about inertia at https://brainly.com/question/1140505

#SPJ11

When the volume of a cylinder filled with a gas is decreased by a piston, the pressure inside rises because of the increased frequency of collisions between gas particles.

This is due to the fact that when the available space is reduced, the particles are forced to move faster in order to maintain their average kinetic energy. Furthermore, the number of collisions between gas particles and the walls of the container increases, resulting in a higher pressure.

Additionally, as the volume decreases, the number of collisions between gas particles and each other increases, which also contributes to the rise in pressure. Therefore, when the volume of a cylinder filled with a gas is decreased by a piston, the pressure inside will rise due to the increased frequency of collisions between gas particles.

Know more about kinetic energy here

https://brainly.com/question/15764612#

#SPJ11

Pluto most closely resembles a terrestrial planet, like the other planets in our solar system. Terrestrial planets are composed mostly of rock and metal, and have solid surfaces. Pluto is believed to have a rocky core surrounded by a mantle of ice, which makes it a terrestrial planet.

Pluto most resembles a terrestrial planet. What are terrestrial planets? Terrestrial planets are planets composed primarily of silicate rocks or metals, which are relatively near to the Sun. They are named after the Earth, as they share many common features. Venus, Earth, and Mars are the three most well-known planets in this group. Pluto is similar to a terrestrial planet since it is composed of rocky material like the Earth. Despite being a dwarf planet, it shares many characteristics with the terrestrial planets. Pluto is a small, icy world that orbits the Sun, is believed to be covered in water ice and various kinds of frozen gases, and has an atmosphere that is primarily composed of nitrogen. Pluto was originally identified as the ninth planet in our solar system but was later reclassified as a dwarf planet because it failed to meet the International Astronomical Union's criteria for being considered a planet. Although Pluto is no longer classified as a planet, it remains one of the most interesting objects in the outer solar system, and the study of Pluto is essential to our understanding of the development of our solar system.

For more details on terrestrial planet, click on the below link:

https://brainly.com/question/7952964

#SPJ11

The sound level for this noise is approximately 50 decibels.

Sound level is a logarithmic measure of the ratio between the sound pressure level of a particular sound wave and a reference level. The reference level is typically set at the threshold of human hearing, which corresponds to an intensity of 10^-12 W/m^2. The sound level (measured in decibels, dB) of a sound wave is given by,

L = 10 log10(I/I0)

where I is the intensity of the sound wave and I0 is the reference intensity, which is typically set at 10^-12 W/m^2.

So, for an intensity of 10^-7 W/m^2 in a typical classroom, we can calculate the sound level as,

L = 10 log10(I/I0) = 10 log10(10^-7/10^-12) = 10 log10(10^5) = 50 dB

To know more about sound, here

brainly.com/question/30546291

#SPJ4

The disk in the lower spine that supports half the weight of a 72 kg person compresses by 0.18 mm.

To calculate the compression of the disk, we can use the formula for the compression of a cylinder under axial load:

ΔL/L = F/(A*E)

Where ΔL is the change in length of the cylinder, L is the original length, F is the force applied, A is the cross-sectional area, and E is Young's modulus.

In this case, the force on the disk is half the weight of the person, which is (1/2)72 kg9.81 m/s² = 353.16 N. The cross-sectional area of the disk is (π/4)*(0.04 m)² = 0.00126 m².

Plugging in these values and the given Young's modulus, we get:

ΔL/L = (353.16 N)/(0.00126 m² * 1.0 × 10⁶ N/m²) = 0.28 × 10⁻³

Multiplying by the original thickness of the disk (5.0 mm), we get the compression of the disk:

ΔL = 0.28 × 10⁻³* 5.0 × 10⁻² m = 0.14 × 10⁻⁴ m = 0.18 mm.

Therefore, the cartilage disk located in the lower spine that sustains 50% of the weight of a person weighing 72 kg will experience a compression of 0.18 mm.

The complete question is: There is a disk of cartilage between each pair of vertebrae in your spine. Young's modulus for cartilage is 1.0 × 106N/m². Suppose a relaxed disk is 4.0 cm in diameter and 5.0 mm thick. If a disk in the lower spine supports half the weight of a 72 kg person, by how many mm does the disk compress?

To know more about compresses, refer here:

https://brainly.com/question/31084499#

#SPJ11