To calculate the size of the particle that is removed with 100% efficiency from a settling chamber, we can use the following assumptions:
1. Determine the settling velocity of the particle: The settling velocity of a particle is the speed at which it falls through a fluid under the influence of gravity. We can use Stoke's Law to calculate the settling velocity: Settling velocity = (2/9) * ((density of particle - density of air) / viscosity of air) * (particle radius)^2 * (gravity).
2. Calculate the maximum particle size for 100% efficiency: In a settling chamber, particles will settle if their settling velocity is greater than the horizontal velocity of the air. Assuming 100% efficiency, the settling velocity should be equal to the horizontal velocity. Therefore, the maximum particle size can be calculated by rearranging Stoke's Law equation as follows: Particle radius = ((9 * horizontal velocity * viscosity of air) / (2 * (density of particle - density of air) * gravity))^(1/2).
3. Substitute the given values into the equation: Horizontal velocity = 0.5 m/s, Temperature = 70 °C (Note: It is important to convert the temperature to absolute temperature, which is in Kelvin. 70 °C + 273.15 = 343.15 K), Specific gravity of the particle = 3.0, Chamber length = 8 m, and Height = 2 m. By substituting these values into the equation, we can calculate the maximum particle size that can be removed with 100% efficiency from the settling chamber.
horizontal velocity : https://brainly.com/question/12870645
#SPJ11
The sales of a plastic widget were estimated to be:
P(t)= 5000 te^-0.91
where t is in weeks, and P(t) is in units per week.
How many widgets were sold in the first 6 weeks?
The given equation for estimating the sales of plastic widgets is P(t) = 5000te^(-0.91), where t represents the number of weeks and P(t) represents the number of units sold per week. To find the number of widgets sold in the first 6 weeks, we need to substitute t = 6 into the equation and calculate the value of P(t). So, let's plug in t = 6 into the equation: P(6) = 5000 * e^(-0.91 * 6). To simplify this calculation, we first evaluate the exponent -0.91 * 6:
-0.91 * 6 = -5.46. Next, we substitute this value back into the equation: P(6) = 5000 * e^(-5.46).
Now, we can use a scientific calculator or computer software to evaluate e^(-5.46), which equals approximately 0.0048.
Finally, we calculate P(6): P(6) = 5000 * 0.0048. Multiplying these values gives us the number of widgets sold in the first 6 weeks.
Therefore, the number of widgets sold in the first 6 weeks is approximately 24. To summarize, the equation P(t) = 5000te^(-0.91) allows us to estimate the number of widgets sold per week. By substituting t = 6 into the equation and performing the necessary calculations, we find that approximately 24 widgets were sold in the first 6 weeks.
To know more about P(t) = 5000te^(-0.91) : https://brainly.com/question/28994705
#SPJ11
vertical shear 250lb at point A
A beam cross section is shown below. The beam is under vertical sh 4.5 in. 6 in. 11 in. 6 in. A F 11 4.5 in. w = 7 in.
At point A on the beam, there is a vertical shear of 250 lb. To understand this, we need to consider the beam's cross section and its dimensions. The beam is 4.5 inches tall and consists of four sections: 6 inches, 11 inches, 6 inches, and 4.5 inches.
Let's analyze it step-by-step:
1. Determine the area of each section:
- Area 1: 6 in x 4.5 in = 27 in^2
- Area 2: 11 in x 4.5 in = 49.5 in^2
- Area 3: 6 in x 4.5 in = 27 in^2
- Area 4: 4.5 in x 4.5 in = 20.25 in^2
2. Calculate the total area of the beam cross section:
Total area = Area 1 + Area 2 + Area 3 + Area 4 = 27 in^2 + 49.5 in^2 + 27 in^2 + 20.25 in^2 = 123.75 in^2
3. Find the shear stress at point A:
Shear stress = Vertical shear force / Area
Shear stress = 250 lb / 123.75 in^2 = 2.02 psi (approximately)
In conclusion, at point A, the vertical shear is 250 lb and the shear stress is approximately 2.02 psi.
Learn more about Shear stress from the given link!
https://brainly.com/question/28194032
#SPJ11
Solve for the support reactions of the beam shown below using 3ME and SDM. Assume beam is prismatic and homogeneous. Draw the shear and moment diagram w=8kN/mP=14kN
we can proceed to draw the shear force and bending moment diagrams;
Bending moment,[tex]M = 0 kN.m2) At x = 2;[/tex]
Bending moment, [tex]M = RA(2) = 32(2) = 64 kN.m3) At x = 4;[/tex]
Bending moment, [tex]M = RA(4) - w(2)(2) = 32(4) - 8(2)(2) = 96 kN.m4)[/tex]
At x = 6;Bending moment, [tex]M = RA(6) - w(4)(2) - P(2) = 32(6) - 8(4)(2) - 14(2) = 60 kN.m5) At x = 8;[/tex]
Bending moment, [tex]M = RA(8) - w(4)(4) - P(4) + w(8)(2) = 32(8) - 8(4)(4) - 14(4) + 8(8)(2) = 0 kN.m[/tex]
The given beam is shown below; It is to determine the support reactions of the beam using 3ME and SDM and also to draw the shear and moment diagram; The load w= 8 kN/m, and P = 14 kN (point load)The first step in solving this problem is to find the reactions by using the equation of equilibrium;
[tex]∑Fy = 0;RA + RB = 8(4) + 14RA + RB = 46 Eq. (1)∑M(A) = 0;RA(4) - 14(2) - 8(2)(2) - RB(4) = 0RA - 2RB = 12 Eq. (2)From Eq. (1);RA = 46 - RB[/tex]
Substituting the value of RA into Eq. (2);(46 - RB) - 2
RB = 124
RB = 14 kN
RB = 14 kN and RA = 46 - RB = 46 - 14 = 32 kNNow that we have found the support reactions,
To know more about moment visit:
https://brainly.com/question/28687664
#SPJ11
A company estimates that its sales will grow continuously at a rate given by the function s(t) = 11. Where S' (t) is the rate at which sales are increasing, in dollars per day, on dayt a) Find the accumulated sales for the first 6 days, b) Find the sales from the 2nd day through the 5th day. (This is the integral from 1 to 5. ) a) The accumulated sales for the first 6 days is $ (Round to the nearest cent as needed. ) b) The sales from the 2nd day through the 5th day is $ (Round to the nearest cent as needed. )
Find the common difference of the arithmetic sequence -11,-17,-23....
Answer:
d = - 6
Step-by-step explanation:
the common difference d is the difference between consecutive terms in the sequence.
- 17 - (- 11) = - 17 + 11 = - 6
- 23 - (- 17) = - 23 + 17 =- 6
the common difference d = - 6
A local university received a $150,000.00 gift to establish an endowment fund for a student scholarship. The endowment fund earns interest at a rate of 3.00% compounded semi-annually. The university will award the scholarship at the end of every quarter, with the first scholarship being awarded four years from now. Calculate the size of the scholarship that the university can award. Scholarship =
A local university has been gifted $150,000 to establish an endowment fund for a student scholarship. The endowment fund earns interest at a rate of 3.00% compounded semi-annually. The university will award the scholarship at the end of every quarter, with the first scholarship being awarded four years from now. the scholarship that the university can award is $3,345.06.
The formula for compound interest is given by:
[tex]A=P(1+r/n)^nt,[/tex]
where P is the principal amount, r is the interest rate, n is the number of times interest is compounded per year, t is the time in years, and A is the amount of money accumulated after t years.
Given, Principal amount = P = $150,000, Interest rate = r = 3% compounded semi-annually, Time = t = 4 years, and Scholarship is awarded at the end of every quarter, which implies n = 4 x 2 = 8 times compounded per year.
The formula for the future value of an annuity is given by:
[tex]FV = (PMT [(1+r/n)^(n*t) - 1]/r) × (r/n),[/tex]
where PMT is the payment, r is the interest rate, n is the number of times interest is compounded per year, t is the time in years, and FV is the future value of the annuity.
We need to find the payment that can be made from the endowment fund every quarter that grows to $150,000 in four years.
Therefore, FV = $150,000, PMT = Scholarship payment, r = 3% compounded semi-annually, n = 4 x 2 = 8 times compounded per year, and t = 4 years. Substituting the values, we get:
[tex]$150,000 = (PMT [(1+0.03/8)^(8*4) - 1]/0.03) × (0.03/8).[/tex]
Solving for PMT, we get PMT = $3,345.06.
Hence, the scholarship that the university can award is $3,345.06.
To know more about compound interest visit:
https://brainly.com/question/14295570
#SPJ11
Consider a three-year bond with face value and coupon rate paid quarterly. Suppose the bond price is traded at a price of . Answer the following questions:
a. (1 mark) What is the current yield on this bond?
b. (1 mark) What is the capital gain on this bond if held till maturity?
c. (1 mark) What is the rate of return on this bond?
d. (2 mark) Define what it means by yield to maturity and explain why it is better than the conventional rate of return.
e. (2 marks) Compute both the per-period and annual yield to maturity on this bond.
f. (2 marks) Assume you bought this bond from this investor at the end of year 2, how much would you pay for that bond if the market interest rate is 5%?
a. Current yield: Coupon payment / Bond price * 100%
b. Capital gain on a bond: Face value - Purchase price
c. Rate of return on a bond: Total return / Initial investment * 100%
d. Yield to maturity (YTM): Total anticipated return on a bond if held until maturity
e. Per-period yield to maturity: Coupon payments over a specific period / Bond price
f. Bond price at the end of year 2 with 5% market interest rate can be calculated using the bond pricing formula.
a. The current yield on a bond is calculated by dividing the annual coupon payment by the bond price.
Since the coupon rate is paid quarterly, we need to multiply the coupon rate by 4 to get the annual coupon payment.
Therefore, the current yield can be calculated as follows: current yield = (Annual coupon payment / Bond price) * 100%.
b. The capital gain on a bond if held till maturity is the difference between the bond's face value and its purchase price.
It represents the profit or loss made by the bondholder upon maturity.
c. The rate of return on a bond takes into account both the coupon payments and any capital gains or losses.
It is calculated by dividing the total return (coupon payments plus capital gain/loss) by the initial investment and expressing it as a percentage.
d. Yield to maturity (YTM) is the total return anticipated on a bond if held until it matures.
It considers the bond's coupon payments, the purchase price, and the final face value.
YTM takes into account the time value of money, as it considers the present value of all future cash flows.
It is considered better than the conventional rate of return because it provides a more accurate representation of the bond's performance and allows for better comparisons between different bonds.
e. To compute the per-period yield to maturity on this bond, we divide the total coupon payments over the three-year period by the bond price.
The annual yield to maturity is then calculated by compounding the per-period yield to maturity.
The exact calculations cannot be performed without the specific values of the bond's face value, coupon rate, and bond price.
f. Without the specific values for the bond's face value, coupon rate, and bond price, it is not possible to calculate the exact amount to be paid for the bond at the end of year 2 when the market interest rate is 5%.
However, it can be determined using the bond pricing formula, which discounts the future cash flows (coupon payments and face value) by the prevailing market interest rate to calculate the present value of the bond.
Learn more about interest rate:
https://brainly.com/question/14556630
#SPJ11
a. Current yield: Coupon payment / Bond price * 100%
b. Capital gain on a bond: Face value - Purchase price
c. Rate of return on a bond: Total return / Initial investment * 100%
d. Yield to maturity (YTM): Total anticipated return on a bond if held until maturity
e. Per-period yield to maturity: Coupon payments over a specific period / Bond price
f. Bond price at the end of year 2 with 5% market interest rate can be calculated using the bond pricing formula.
a. The current yield on a bond is calculated by dividing the annual coupon payment by the bond price.Since the coupon rate is paid quarterly, we need to multiply the coupon rate by 4 to get the annual coupon payment.Therefore, the current yield can be calculated as follows: current yield = (Annual coupon payment / Bond price) * 100%.
b. The capital gain on a bond if held till maturity is the difference between the bond's face value and its purchase price.It represents the profit or loss made by the bondholder upon maturity.
c. The rate of return on a bond takes into account both the coupon payments and any capital gains or losses.It is calculated by dividing the total return (coupon payments plus capital gain/loss) by the initial investment and expressing it as a percentage.
d. Yield to maturity (YTM) is the total return anticipated on a bond if held until it matures.It considers the bond's coupon payments, the purchase price, and the final face value.YTM takes into account the time value of money, as it considers the present value of all future cash flows.It is considered better than the conventional rate of return because it provides a more accurate representation of the bond's performance and allows for better comparisons between different bonds.
e. To compute the per-period yield to maturity on this bond, we divide the total coupon payments over the three-year period by the bond price.The annual yield to maturity is then calculated by compounding the per-period yield to maturity.The exact calculations cannot be performed without the specific values of the bond's face value, coupon rate, and bond price.
f. Without the specific values for the bond's face value, coupon rate, and bond price, it is not possible to calculate the exact amount to be paid for the bond at the end of year 2 when the market interest rate is 5%.However, it can be determined using the bond pricing formula, which discounts the future cash flows (coupon payments and face value) by the prevailing market interest rate to calculate the present value of the bond.
Learn more about interest rate:
brainly.com/question/14556630
#SPJ11
A truck container having dimensions of 12x4.4x2.0m began accelerating at a rate of 0.7m/s^2.if the truck is full of water, how much water is spilled in m^3 provide your answer in three decimal places
A truck container having dimensions of 12x4.4x2.0m The amount of water spilled is approximately 12 cubic meters.
The amount of water spilled, we need to calculate the displacement of the water along the direction of acceleration. Since the truck is accelerating in the x-direction, we will calculate the displacement in the x-direction.
The formula for displacement (s) can be calculated using the equation of motion:
s = ut + (1/2)at²
where u is the initial velocity (which is assumed to be zero in this case), a is the acceleration, and t is the time.
In this case, the acceleration is 0.7 m/s² and we need to find the displacement in the x-direction. Since the truck is moving in a straight line, the displacement in the x-direction is equal to the length of the truck container, which is 12 meters.
Using the formula for displacement, we can calculate the time it takes for the truck to reach the displacement of 12 meters:
12 = (1/2)(0.7)t²
Simplifying the equation:
0.35t² = 12
t² = 12 / 0.35
t² = 34.2857
Taking the square root of both sides:
t = √34.2857
t ≈ 5.857 seconds (rounded to three decimal places)
Now, we can calculate the amount of water spilled by substituting the time into the displacement equation:
s = ut + (1/2)at²
s = 0 + (1/2)(0.7)(5.857)²
s ≈ 0 + 0.5(0.7)(34.2857)
s ≈ 0 + 11.99999
s ≈ 12 meters
Therefore, the amount of water spilled is approximately 12 cubic meters.
To know more about dimensions click here :
https://brainly.com/question/13040261
#SPJ4
One thousand ft3/h of light naphtha of API equaling 80 is fed into an isomerization unit. Make a material balance (1b/h) around this unit.
The material balance around the isomerization unit shows that 150,000 lb/h of light naphtha with an API gravity of 80 is fed into the unit, and the same amount of light naphtha is produced as the output stream.
Make material balance around the isomerization unit, we need to consider the input and output streams of light naphtha. 1000 ft3/h of light naphtha with an API gravity of 80 is being fed into the unit, we can calculate the mass flow rate using the specific gravity formula. The specific gravity of a liquid is equal to its API gravity divided by 141.5.
First, let's calculate the specific gravity of the light naphtha:
API gravity = 80
Specific gravity = API gravity / 141.5 = 80 / 141.5 = 0.565
the mass flow rate, we need to know the density of the light naphtha. Let's assume a density of 150 lb/ft3 for light naphtha.
Mass flow rate = Volume flow rate * Density
Mass flow rate = 1000 ft3/h * 150 lb/ft3 = 150,000 lb/h
Now, let's consider the output stream of the isomerization unit. Since the question asks for a material balance in lb/h, we need to convert the volume flow rate to mass flow rate using the density of the output stream.
Assuming a density of 150 lb/ft3 for the output stream, the mass flow rate of the output stream would also be 150,000 lb/h, as the question does not provide any information about changes in mass during the isomerization process.
The material balance around the isomerization unit shows that 150,000 lb/h of light naphtha with an API gravity of 80 is fed into the unit, and the same amount of light naphtha is produced as the output stream.
Learn more about isomerization with the given link,
https://brainly.com/question/9116728
#SPJ11
The heading of the grids of an AB alignment is 100º 22', while
the magnetic declination is 8º30' E. What is the true, magnetic and
grid azimuth of this alignment?
The resulting values will give us the true azimuth and magnetic azimuth of the alignment.
To calculate the true, magnetic, and grid azimuth of an alignment, we need to consider the following information:
1. True Azimuth:
The true azimuth represents the direction of the alignment with respect to True North.
2. Magnetic Declination:
Magnetic declination is the angle between True North and Magnetic North at a specific location. It indicates the angular difference between the True North and the direction indicated by a magnetic compass.
3. Magnetic Azimuth:
The magnetic azimuth is the direction of the alignment with respect to Magnetic North. It is obtained by applying the magnetic declination to the true azimuth.
4. Grid Azimuth:
The grid azimuth is the direction of the alignment with respect to the grid north, which is aligned with the grid lines on a map or survey.
Given:
Heading of grids (Grid Azimuth) = 100º 22'
Magnetic declination = 8º 30' E
To calculate the true azimuth, we subtract the magnetic declination from the grid azimuth:
True Azimuth = Grid Azimuth - Magnetic Declination
Calculating the true azimuth:
True Azimuth = 100º 22' - 8º 30'
To calculate the magnetic azimuth, we add the magnetic declination to the grid azimuth:
Magnetic Azimuth = Grid Azimuth + Magnetic Declination
Calculating the magnetic azimuth:
Magnetic Azimuth = 100º 22' + 8º 30'
To know more about lines visit:
brainly.com/question/2696693
#SPJ11
From among the following alternatives to buffer
within a range acceptable pH values, where a
system of NaClO/HCIO,
which of these combinations causes a lower
change in pH, after
pour in each of them the same amount of acid
or strong base? a) 1.0L de NaClO0.100M,HClO0.100M b) 2.0 L de NaClO0.0100M,HClO0.0100M C) 1.0 L de NaClO0.0250M,HClO0.0250M d) 100.0 mL de NaClO 0.500M,HClO0.500M e) 1.0 L de NaClO0.0725M, HClO 0.0725M
The combination which causes the least change in pH after pouring in the same amount of acid or strong base from the following alternatives to buffer within an acceptable pH range is,Option C.
Buffer solutions are those solutions that resist change in pH upon the addition of small amounts of acid or base. The resistance of a buffer solution to a change in pH on addition of acid or base depends on the concentration of the weak acid and its conjugate base. A buffer solution typically consists of a weak acid and its conjugate base. The Henderson-Hasselbalch equation describes the relationship between the pH of a buffer solution and the pKa of the weak acid or weak base in the buffer solution.
The combination which causes the least change in pH after pouring in the same amount of acid or strong base from the given options is Option C (1.0 L of NaClO 0.0250 M, HClO 0.0250 M) because it has the buffer capacity and this capacity depends on the concentration of the weak acid or base and its conjugate salt, which is a measure of the resistance to pH change.
To know more about strong base visit:-
https://brainly.com/question/9939772
#SPJ11
Answer:
All the given combinations (a, b, c, d, and e) cause an equal change in pH when the same amount of acid or strong base is added.
Step-by-step explanation:
To determine the change in pH after adding the same amount of acid or strong base, we need to consider the acid-base equilibrium and the dissociation of HClO.
HClO (aq) ⇌ H+ (aq) + ClO- (aq)
The equilibrium expression is given by:
K_a = [H+][ClO-] / [HClO]
As the concentrations of HClO and ClO- are equal in each case, the equilibrium expression simplifies to:
K_a = [H+] / [HClO]
The pH is given by the equation:
pH = -log[H+]
We can observe that the change in pH depends on the ratio of [H+] to [HClO]. A lower change in pH will occur when the ratio of [H+] to [HClO] is smaller.
Comparing the options:
a) [H+] / [HClO] = 0.100M / 0.100M = 1
b) [H+] / [HClO] = 0.0100M / 0.0100M = 1
c) [H+] / [HClO] = 0.0250M / 0.0250M = 1
d) [H+] / [HClO] = 0.500M / 0.500M = 1
e) [H+] / [HClO] = 0.0725M / 0.0725M = 1
Based on these calculations, all the options result in the same ratio of [H+] to [HClO], which means they will cause the same change in pH when the same amount of acid or strong base is added.
Therefore, all the options (a, b, c, d, and e) cause an equal change in pH.
Learn more about PH from here:
https://brainly.com/question/12609985
#SPJ11
In Malaysia, landslides are among the deadly hazards which occur quite frequently during the rainy seasons. Undeniable, in some cases, landslides occur as a consequence of flawed design, improper cons
In Malaysia, landslides are a common and dangerous occurrence, especially during the rainy seasons. There are various factors that can contribute to landslides, including flawed design and improper construction practices.
Here is a step-by-step explanation of the causes and consequences of landslides in Malaysia:
1. Heavy rainfall: Malaysia experiences intense rainfall during the rainy seasons, which saturates the soil and weakens its stability.
2. Deforestation: The extensive clearing of forests for agriculture, urbanization, and logging reduces the natural protection provided by trees and their roots, making slopes more susceptible to erosion and landslides.
3. Improper land use planning: Inadequate consideration of geological conditions and slope stability during land development can lead to unstable slopes and increased landslide risk.
4. Poor construction practices: Faulty design, improper drainage systems, and inadequate slope stabilization measures during construction can contribute to landslides.
5. Consequences: Landslides can result in loss of lives, damage to infrastructure, displacement of communities, and environmental degradation.
To mitigate the risk of landslides, Malaysia has implemented measures such as slope stabilization techniques, reforestation efforts, and stricter regulations for land development. These initiatives aim to minimize the occurrence and impact of landslides, ensuring the safety and well-being of the population.
learn more about factors from given link
https://brainly.com/question/11930302
#SPJ11
016= Which of the following is the base case of induction statement 2n+1≤2n,4n≥3 a) 3≤4 b) 6≤8 c) 7≤8 d) 9≤16 e) 8≤16 Management of the college wants 10 organlie the end of the year party. The mustic Management of 195 people at the college ls as followis: 99 like lulu music. 96 like Nrabesase music, 99 IVe Blues music, 94 like Arabesque and Blues. 96 like lulu and blues, 93 , like all the three. If people at the college like at least one of these three music, how many people ln the college like /uju and Arabesque? a) 1 b) 2 c) 3 d) 4 e) 5
The correct answer is option d) 9 ≤ 16.The base case of an induction statement is the initial condition that is used to prove the statement for all subsequent cases.
In the given question, the induction statement is 2n+1 ≤ 2n, 4n ≥ 3. To find the base case, we need to substitute the value of n that satisfies this inequality.
Let's try substituting n=1:
2(1) + 1 ≤ 2(1)
3 ≤ 2
This inequality is not true, so n=1 is not the base case.
Let's try substituting n=2:
2(2) + 1 ≤ 2(2)
5 ≤ 4
Again, this inequality is not true.
We need to keep trying different values of n until we find the one that satisfies the inequality.
Substituting n=3:
2(3) + 1 ≤ 2(3)
7 ≤ 6
This inequality is also not true.
Substituting n=4:
2(4) + 1 ≤ 2(4)
9 ≤ 8
This inequality is not true either.
Finally, substituting n=5:
2(5) + 1 ≤ 2(5)
11 ≤ 10
This inequality is true. So, n=5 is the base case for the induction statement 2n+1 ≤ 2n, 4n ≥ 3.
The question requires us to find the number of people at the college who like both lulu and Arabesque music. If we subtract that from the number of people who like lulu and blues, we will find out the number of people who like lulu and blues but not Arabesque. This is 96 - 93 = 3. Similarly, if we subtract 94 (people who like Arabesque and blues but not lulu) from 99 (people who like blues), we get 5. Adding the two values together, we get the number of people who like lulu and Arabesque as 3 + 5 = 8. Therefore, the correct answer is option (e) 8 people.
To know more about hypothesis visit:
https://brainly.com/question/32562440
#SPJ11
Why are maps in the PLSS measured in chains and links? 2. What is the distance from an IP (initial point) to the NE corner of Sec. 18, T3S, RIW? Draw picture to show the location of this point in re
The reasons why maps in the PLSS (Public Land Survey System) are measured in chains and links are as follows:In the PLSS, land areas are divided into 6-mile by 6-mile squares called townships.
Each township is further divided into 36 1-mile by 1-mile squares known as sections. Each section is then divided into quarters, or 160-acre plots.
1 chain = 66 feet
= 20.12 meters
1 link = 7.92 inches
= 0.201 meters
Using chains and links, which are units of measurement that were commonly used at the time the PLSS was established, allowed for easy subdivision of townships and sections into smaller plots.
The location of an Initial Point (IP) and the Northeast corner of Section 18, Township 3 South, Range I West is given below:In the PLSS system, an IP or Initial Point is the point of reference for the survey. It is the starting point for all surveys in a particular area, and all measurements are taken relative to the IP.
The IP for the Principal Meridian and Base Line used in Michigan is located near the intersection of Woodward Avenue and 8 Mile Road in Detroit, Michigan.
Know more about the (Public Land Survey System)
https://brainly.com/question/30580520
#SPJ11
Air at 500 kPa and 400 k enters an adiabatic nozzle which has inlet to exit area ratio of 3:2, velocity of the air at the entry is 100 m/s and the exit is 360 m/s. Determine the exit pressure and temperature.
The air at 500 kPa and 400 k enters an adiabatic nozzle with an inlet to exit area ratio of 3:2. The velocity of the air at the entry is 100 m/s, and at the exit, it is 360 m/s. We need to determine the exit pressure and temperature.
To solve this problem, we can use the principle of conservation of mass and the adiabatic flow equation. The conservation of mass states that the mass flow rate at the inlet is equal to the mass flow rate at the exit.
1. Conservation of mass:
Since the mass flow rate remains constant, we can equate the mass flow rate at the inlet and the mass flow rate at the exit.
m_dot_inlet = m_dot_exit
The mass flow rate can be expressed as the product of density (ρ), velocity (V), and area (A). So, we can rewrite the equation as:
ρ_inlet * A_inlet * V_inlet = ρ_exit * A_exit * V_exit
2. Adiabatic flow equation:
The adiabatic flow equation relates pressure, temperature, and density of a fluid flowing through a nozzle. It can be expressed as:
P_inlet * (ρ_inlet/ρ)^γ = P * (ρ/ρ_exit)^γ
where P is the pressure at any point along the nozzle, γ is the specific heat ratio, and ρ is the density at that point.
3. Area ratio:
We are given that the area ratio of the nozzle is 3:2, which means A_exit = (2/3) * A_inlet.
Now, let's solve for the exit pressure and temperature using these equations:
First, let's calculate the density at the inlet and the exit using the ideal gas law:
ρ_inlet = P_inlet / (R * T_inlet)
ρ_exit = P_exit / (R * T_exit)
where R is the specific gas constant.
We can rearrange the adiabatic flow equation to solve for the exit pressure:
P_exit = P_inlet * (ρ_inlet/ρ_exit)^γ * (ρ_exit/ρ_inlet)^γ
Since the density terms cancel out, we have:
P_exit = P_inlet * (ρ_inlet/ρ_exit)^(2*γ)
Next, let's calculate the area values:
A_exit = (2/3) * A_inlet
Now, let's substitute the area values and solve for the exit pressure:
P_inlet * (ρ_inlet/ρ_exit)^(2*γ) = P_exit
P_inlet * (ρ_inlet/ρ_exit)^(2*γ) = P_inlet * (2/3)^(2*γ) * ρ_exit^(2*γ)
Now, let's solve for the exit temperature using the ideal gas law:
T_exit = (P_exit * ρ_exit) / (R * ρ_exit)
Finally, we can substitute the values we know into the equations to find the exit pressure and temperature.
Please provide the values of γ, R, T_inlet, and P_inlet so that we can calculate the exit pressure and temperature accurately.
air at 500 kPa and 400 k and area ratio of 3:2 : https://brainly.com/question/15186490
#SPJ11
3.7) For a long time period, if a watershed receives 300 mm of
precipitation and has a 200 mm evapotranspiration annually,
determine annual average runofff.
The annual average runoff for the watershed is 100 mm.
To determine the annual average runoff, we need to calculate the difference between the precipitation and evapotranspiration.
Given:
Precipitation = 300 mm
Evapotranspiration = 200 mm
To find the annual average runoff, we subtract the evapotranspiration from the precipitation:
Annual Average Runoff = Precipitation - Evapotranspiration
Annual Average Runoff = 300 mm - 200 mm
Annual Average Runoff = 100 mm
Therefore, The watershed's average annual runoff is 100 mm.
learn more about average from given link
https://brainly.com/question/130657
#SPJ11
Some pH meters are designed for a three-point calibration at pH 4, 7, and 10. Ours are only calibrated with a two-point procedure at 4 and 7 or 7 and 10. Which range would you expect we are calibrating them at for this experiment? Why?
The range that we would expect the pH meters are calibrated at for this experiment is between pH 4 and pH 7. This is because,the pH meters are calibrated with a two-point procedure at pH 4 and 7 or 7 and 10.
Therefore, we can conclude that the pH meters are calibrated with a two-point procedure within the range of pH 4 and 7 or pH 7 and 10. Since we do not have information on which two points the pH meters are calibrated, we can assume that the calibration is performed at pH 4 and pH 7 which is a standard method of calibration of pH meters.
Hence,the pH meters are calibrated at the range of pH 4 and pH 7.
The pH meters are calibrated at the range of pH 4 and pH 7. This is because the calibration is performed with a two-point procedure, and the standard procedure involves calibrating pH meters at pH 4 and pH 7.
To know more about pH meters visit :
brainly.com/question/29442555
#SPJ11
Consider the points below. P(1, 0, 1), Q(-2, 1, 4), R(6, 2, 7) (a) Find a nonzero vector orthogonal to the plane through the points P, Q, and R. Need Help? (b) Find the area of the triangle PQR. SCALC9 12.4.029.
Answer:
(a) (0, 3, -1)
(b) (11/2)√10 ≈ 17.3925
Step-by-step explanation:
Given the points P(1, 0, 1), Q(-2, 1, 4), R(6, 2, 7), you want a normal vector to the plane containing them, and the area of the triangle they form.
Cross productThe cross product of two vectors is orthogonal to both. Its magnitude is ...
|PQ × PR| = |PQ|·|PR|·sin(θ) . . . . where θ is the angle between PQ and PR
The area of triangle PQR can be found from the side lengths PQ and PR as ...
A = 1/2·PQ·PR·sin(θ)
where θ is the angle between the sides.
This means the area of the triangle is half the magnitude of the cross product of two vectors that are its sides.
(a) Orthogonal vectorThe attachment shows the cross product of vectors PQ and PR is (0, 33, -11). The components of this vector have a common factor of 11, so we can reduce it to (0, 3, -1).
A normal vector plane PQR is (0, 3, -1).
(b) AreaThe area of the triangle is ...
A = 1/2√(0² +33² +(-11)²) = 1/2(11√10)
The area of triangle PQR is (11/2)√10 ≈ 17.3925 square units.
__
Additional comment
The area figure can be confirmed by finding the triangle side lengths using the distance formula, then Heron's formula for area from side lengths. The arithmetic is messy, but the result is the same.
<95141404393>
Predict the molecular geometry about S in the molecule SO_2. a) linear b) trigonal planar c) bent d) trigonal pyramidal
The molecular geometry about sulfur (S) in the molecule SO2 is: c) bent because SO2 has a bent molecular geometry due to its structure. It consists of a sulfur atom bonded to two oxygen atoms.
The sulfur atom has two lone pairs of electrons, and the oxygen atoms are bonded to the sulfur atom through double bonds.
The arrangement of the electron pairs around the sulfur atom is trigonal planar, but the presence of the lone pairs causes a deviation from the ideal bond angle.
As a result, the molecule takes on a bent or V-shaped geometry.
Learn more about sulfur from the given link!
https://brainly.com/question/2116588
#SPJ11
There are two cold streams and two hot stream with following information. C1(FCp=4893 Btu/hr oF Tin=770F: Tout-133 oF); C2 (FCp=5x105 Btu/hr OF: Tin=156 OF: Tout=1960F): H1 (1.23 x 104 Btu/hr oF: Tin=244 oF Tout=770F) C2(FCp=1946 Btu/hroF: Tin=2440F: Tout =1290F). Calculate the total avaialbale with hot stream (10-5)
The total available heat with hot stream (10-5) is given as: Q = QH + QCQ = 15,096,053 - 10,559,172 = 4,536,881 Btu/hr.
In order to determine the total available heat with hot streams, we need to calculate the total available heat with the hot streams and cold streams respectively and then add both of them.
Total available heat with hot streams is given by:
QH = mH x Cp x (THout - THin)
Where mH is the mass flow rate of the hot stream, Cp is the specific heat of the hot stream,
THin is the inlet temperature of hot stream and THout is the outlet temperature of hot stream.
C1: FCp=4893 Btu/hr oF; Tin=770F; Tout=133oFQ1 = 4893 × (770 - 133) = 2,876,901 Btu/hr
C2: FCp=5x105 Btu/hr OF; Tin=156 OF; Tout=1960FQ2 = 5 × 10⁵ × (1960 - 156) = 9,702 × 10⁶ Btu/hrH1: Q = 1.23 × 10⁴ (770 - 244) = 7,636,000 Btu/hr
C3: FCp=1946 Btu/hroF; Tin=244 OF; Tout =1290FQ3 = 1946 × (1290 - 244) = 2,518,152 Btu/hr
Total available heat with hot streams:
QH = Q1 + Q2 + Q3
QH = 2,876,901 + 9,702,000 + 2,518,152
= 15,096,053 Btu/hr
Total available heat with cold streams is given by:
QC = mC x Cp x (TCin - TCout)
Where mC is mass flow rate of the cold stream, Cp is the specific heat of cold stream, TCin is the inlet temperature of cold stream and TCout is the outlet temperature of cold stream.
C1: FCp=4893 Btu/hr oF; Tin=770F; Tout=133oFQC1 = 4893 × (133 - 77) = 275,172 Btu/hr
C2: FCp=5x105 Btu/hr OF; Tin=156 OF; Tout=1960FQC2 = 5 × 10⁵ × (156 - 1960) = -9,202 × 10⁶ Btu/hr
C3: FCp=1946 Btu/hr; Tin=244 OF; Tout =1290FQ
C3 = 1946 × (244 - 1290) = -1,632,344 Btu/hr
Total available heat with cold streams:
QC = QC1 + QC2 + QC3
QC = 275,172 - 9,202 × 10⁶ - 1,632,344 = -10,559,172 Btu/hr
Therefore, the total available heat with hot stream (10-5) is given as:Q = QH + QCQ = 15,096,053 - 10,559,172 = 4,536,881 Btu/hr.
Know more about hot stream here:
https://brainly.com/question/13686045
#SPJ11
1. (5 pts) The (per hour) production function for bottles of coca-cola is q=1000K L
, where K is the number of machines and L is the number of machine supervisors. a. (2 pts) What is the RTS of the isoquant for production level q? [Use the following convention: K is expressed as a function of L b. (1 pt) Imagine the cost of operating capital is $40 per machine per hour, and labor wages are $20/ hour. What is the ratio of labor to capital cost? c. (2 pts) How much K and L should the company use to produce q units per hour at minimal cost (i.e. what is the expansion path of the firm)? What is the corresponding total cost function?
The RTS of the isoquant is 1000K, indicating the rate at which labor can be substituted for capital while maintaining constant production. The labor to capital cost ratio is 0.5. To minimize the cost of producing q units per hour, the specific value of q is needed to find the optimal combination of K and L along the expansion path, represented by the cost function C(K, L) = 40K + 20L.
The RTS (Rate of Technical Substitution) measures the rate at which one input can be substituted for another while keeping the production level constant. To determine the RTS, we need to calculate the derivative of the production function with respect to L, holding q constant.
Given the production function q = 1000KL, we can differentiate it with respect to L:
d(q)/d(L) = 1000K
Therefore, the RTS of the isoquant for production level q is 1000K.
The ratio of labor to capital cost can be calculated by dividing the labor cost by the capital cost.
Labor cost = $20/hour
Capital cost = $40/machine/hour
Ratio of labor to capital cost = Labor cost / Capital cost
= $20/hour / $40/machine/hour
= 0.5
The ratio of labor to capital cost is 0.5.
To find the combination of K and L that minimizes the cost of producing q units per hour, we need to set up the cost function and take its derivative with respect to both K and L.
Let C(K, L) be the total cost function.
The cost of capital is $40 per machine per hour, and the cost of labor is $20 per hour. Therefore, the total cost function can be expressed as:
C(K, L) = 40K + 20L
To produce q units per hour at minimal cost, we need to find the values of K and L that minimize the total cost function while satisfying the production constraint q = 1000KL.
The expansion path of the firm represents the combinations of K and L that minimize the cost at different production levels q.
Learn more about production
brainly.com/question/31859289
#SPJ11
b/4 ≥ 1 or 5b < 10
Please help with this
The solution of the inequality b/4 ≥ 1 or 5b < 10 is {b : b ≥ 4 or b < 2}.
The inequality provided is:
b/4 ≥ 1
To solve this inequality, we can multiply both sides of the inequality by 4 to isolate the variable b:
4 * (b/4) ≥ 4 * 1
b ≥ 4
Therefore, the solution to the inequality is b ≥ 4.
However, there seems to be a discrepancy between the inequality provided (b/4 ≥ 1) and the second statement (5b < 10). If we consider the second statement, we have:
5b < 10
To solve this inequality, we can divide both sides by 5 to isolate the variable b:
(5b)/5 < 10/5
b < 2
Therefore, the solution to the second inequality is b < 2.
It's important to note that there is no common solution between b ≥ 4 (from the first inequality) and b < 2 (from the second inequality). The two inequalities are inconsistent and cannot both be true simultaneously.
Know more about inequality here:
https://brainly.com/question/30238989
#SPJ8
A river that feeds into a lake has elevated nitrate from agricultural runoff (0.8 mg-N/L). The river has a flow of 240 ft³/s. Additionally, a wastewater treatment plant discharges 12 MGD of effluent with 5 mg-N/L of nitrate into the river. Nitrate is taken up in the lake by bacteria at a rate of 1.92 d¹¹. The lake as a volume of 3,000,000 ft and can be considered to be completely mixed. A drinking water treatment plant downstream of the lake requires that river water at the intake has a maximum of 1 mg-N/L of nitrate. Another wastewater treatment plant will be added upstream of the lake and will discharge 8 MGD of flow. What should be the permit limit for nitrate in mg-N/L for that new plant, so that the drinking water quality is not compromised? 1ft-7.48 gal MGD = 106 gal/d
The permit limit for nitrate in mg-N/L for the new plant should be 4.18 mg-N/L.
Given, River flow rate = 240 ft³/s
Nitrate level due to agricultural runoff = 0.8 mg-N/L
Discharge from wastewater treatment plant = 12 MGD
Nitrate level in the discharge from wastewater treatment plant = 5 mg-N/L
Nitrate uptake rate by bacteria = 1.92 d¹¹
Lake volume = 3,000,000 ft³
Permissible nitrate level at drinking water treatment plant = 1 mg-N/L
Additional discharge from new wastewater treatment plant = 8 MGD
To calculate the maximum permissible nitrate limit for the new wastewater treatment plant so that drinking water quality is not compromised,
we need to first calculate the nitrate level at the intake of the drinking water treatment plant.
It can be calculated as follows:
Let the nitrate level in the river after mixing be N.
Then, Total nitrate inflow rate = Nitrate outflow rate
240 x N + 12 x 106 x 5 = 3,000,000 x 1.92 d¹¹
Now,240 N + 12 x 106 x 5 = 3,000,000 x 1.92 d¹¹
240 N = 3,000,000 x 1.92 d¹¹ - 12 x 106 x 5N = (3,000,000 x 1.92 d¹¹ - 12 x 106 x 5) / 240N = 32.64 d⁻¹
The nitrate inflow rate from the new wastewater treatment plant will add an additional nitrogen inflow rate of 8 x 106 x Permit limit of nitrate from new treatment plant.
Then, Total nitrate inflow rate = Nitrate outflow rate
240 x N + 12 x 106 x 5 + 8 x 106 x Permit limit of nitrate from new treatment plant
= 3,000,000 x 1.92 d¹¹
Now,
240 N + 12 x 106 x 5 + 8 x 106 x Permit limit of nitrate from new treatment plant
= 3,000,000 x 1.92 d¹¹
240 N = 3,000,000 x 1.92 d¹¹ - 12 x 106 x 5 - 8 x 106 x Permit limit of nitrate from new treatment plant
N = (3,000,000 x 1.92 d¹¹ - 12 x 106 x 5 - 8 x 106 x Permit limit of nitrate from new treatment plant) / 240N
= 32.64 d⁻¹ - 8 x 106 x Permit limit of nitrate from new treatment plant / 240
Now, Nitrate level at the intake of drinking water treatment plant = 1 mg-N/L
Therefore,32.64 d⁻¹ - 8 x 106 x Permit limit of nitrate from new treatment plant / 240 = 1 mg-N/L
Permit limit of nitrate from new treatment plant = (32.64 d⁻¹ - 240) / 8 x 106
Permit limit of nitrate from new treatment plant = 4.18 mg-N/L
Hence, the permit limit for nitrate in mg-N/L for the new plant should be 4.18 mg-N/L.
To know more about Nitrate level visit:
https://brainly.com/question/32373608
#SPJ11
(1 point) Evaluate the integral 3x² - - 6x 1 - x³ 3x²x+3 dx = 3x² - 6x 1 - x³ 3x²-x+3 da using AC A 1 B x+1 + I C - 3
The integral can be evaluated using the partial fraction decomposition. The integrand can be written as the sum of three fractions, each with a denominator of (3x^2 - x + 3). The numerators of these fractions can be found using the method of residues. The answer is x^4/12 + C = x^4/12
The first step is to factor the denominator of the integrand. This gives us (3x^2 - x + 3) = (3(x-1)(x-3)). We can then write the integrand as the sum of three fractions, each with a denominator of (3x^2 - x + 3). The numerators of these fractions can be found using the method of residues.
The method of residues involves finding the roots of the denominator and then evaluating the integrand at these roots. The roots of (3x^2 - x + 3) are x = 1 and x = 3. The residues at these roots are 1 and -1, respectively. This gives us the following three fractions:
(1/3) * (1/(3x^2 - x + 3)) + (-1/3) * (1/(3x^2 - x + 3))
We can now evaluate the integral using the reverse power rule. The reverse power rule states that the integral of x^n dx = (x^(n+1))/n+1 + C. This gives us the following:
(1/3) * (x^(3+1))/3+1 + (-1/3) * (x^(3+1))/3+1 + C
This simplifies to x^4/12 - x^4/12 + C = 0 + C. The constant of integration C can be found by evaluating the integral at a known point. For example, if we evaluate the integral at x = 0, we get C = 0. This gives us the final answer:
x^4/12 + C = x^4/12
Learn more about numerators here: brainly.com/question/30438048
#SPJ11
One hundred twenty students attended the dedication ceremony of a new building on a college campus. The president of the traditionally female college announced a new expansion program which included plans to make the college coeducational. The number of students who learned of the new program thr later is given by the function below. 3000 1 (0) - 1+ Be If 240 students on campus had heard about the new program 2 hr after the ceremony, how many students had heard about the policy after 6 hr? X students How fast was the news spreading after 6 hr? students/hr
The number of students who learned about the new program at a traditionally female college can be modeled by the function N(t) = 3000 / (1 + e^(-t+1)) - 1, where t represents the time in hours since the dedication ceremony. Given that 240 students had heard about the program 2 hours after the ceremony, we can use this information to determine how many students had heard about it after 6 hours. Additionally, we can find the rate at which the news was spreading after 6 hours.
To find the number of students who had heard about the program after 6 hours, we substitute t = 6 into the function N(t). Thus, N(6) = 3000 / (1 + e^(-6+1)) - 1. Evaluating this expression gives us the number of students who had heard about the program after 6 hours.
To determine the rate at which the news was spreading after 6 hours, we need to find the derivative of N(t) with respect to t and evaluate it at t = 6. Taking the derivative, we have dN/dt = (3000e^(-t+1)) / (1 + e^(-t+1))^2. Evaluating this derivative at t = 6, we get dN/dt | t=6 = (3000e^(-6+1)) / (1 + e^(-6+1))^2. This gives us the rate at which the news was spreading after 6 hours, measured in students per hour.
Therefore, by substituting t = 6 into the function N(t), we can determine the number of students who had heard about the program after 6 hours, and by evaluating the derivative of N(t) at t = 6, we can find the rate at which the news was spreading at that time.
Learn more about function here: brainly.com/question/31062578
#SPJ11
If 40.5 mol of an ideal gas occupies 72.5 L at 43.00∘C, what is the pressure of the gas? P= atm
Therefore, the pressure of the gas is approximately 144.79 atm.
To find the pressure of the gas, we can use the ideal gas law, which states:
PV = nRT
where P is the pressure, V is the volume, n is the number of moles, R is the ideal gas constant, and T is the temperature in Kelvin.
First, we need to convert the temperature from Celsius to Kelvin by adding 273.15:
T = 43.00 + 273.15 = 316.15 K
Now we can rearrange the ideal gas law equation to solve for pressure:
P = (nRT) / V
P = (40.5 mol * 0.0821 atm·L/mol·K * 316.15 K) / 72.5 L
P ≈ 144.79 atm
To know more about pressure,
https://brainly.com/question/13199450
#SPJ11
In 2018, there were z zebra mussels in a section of a river. In 2019, there were
z³ zebra mussels in that same section. There were 729 zebra mussels in 2019.
How many zebra mussels were there in 2018? Show your work.
There were 9 zebra mussels in 2018.
We are given that in 2018, there were z zebra mussels in a section of the river.
In 2019, there were [tex]z^3[/tex] zebra mussels in the same section.
And it is mentioned that there were 729 zebra mussels in 2019.
To find the value of z, we can set up an equation using the given information.
We know that [tex]z^3[/tex] represents the number of zebra mussels in 2019.
And we are given that [tex]z^3[/tex] = 729
To find the value of z, we need to find the cube root of 729.
∛(729) = 9
So, z = 9.
Therefore, in 2018, there were 9 zebra mussels in the section of the river.
You can verify this by substituting z = 9 into the equation:
[tex]z^3 = 9^3 = 729.[/tex]
Hence, there were 9 zebra mussels in 2018.
for such more question on zebra mussels
https://brainly.com/question/31192031
#SPJ8
consumption is 200 lpcd. (CLO1/PLO1) Q4: Explain the different physical tests performed for the drinking water. Also write their WHO guideline values. (CLO2/PL07)
Physical, Color, Turbidity, PH, Hardness and other tests are conducted to determine whether the water is suitable for drinking. WHO has also provided guideline values for each test.
Different physical tests performed for drinking water and their WHO guideline values are mentioned below:
Physical tests performed for drinking water
Color test: This test is performed to detect the presence of organic and inorganic matter in the water. WHO guideline value for color is <15 TCU.
Turbidity test: Turbidity test is performed to detect suspended particles in the water. WHO guideline value for turbidity is <5 NTU.
PH test: PH test is performed to determine the acidity or alkalinity of the water. WHO guideline value for PH is 6.5-8.5.
Hardness test: Hardness test is performed to detect the amount of minerals like calcium and magnesium present in the water. WHO guideline value for hardness is 500 mg/l.
Nitrates test: This test is performed to detect the presence of nitrate in the water. WHO guideline value for nitrate is 50 mg/l.
Chloride test: Chloride test is performed to detect the amount of salt present in the water. WHO guideline value for chloride is 250 mg/l.
Fluoride test: Fluoride test is performed to detect the amount of fluoride present in the water. WHO guideline value for fluoride is 1.5 mg/l.
Therefore, all the above-mentioned tests are conducted to determine whether the water is suitable for drinking. WHO has also provided guideline values for each test.
To know more about magnesium, visit
https://brainly.com/question/15168276
#SPJ11
Use Parme's method to design a rectangular column to resist D.L = 500 kN, L.L = 200 kN, MDX = 50 kN.m, MLx = 60 kN.m, MDy = 30 kN.m, MLx = 30 kN.m. Material mechanical properties are: fc- = 25 MPa anf fy = 400 MPa. Assume d = 0.85 h (d- = 63 mm).
To design a rectangular column using Parme's method, you need to consider the design loads and material properties. Based on the given information, the column needs to resist a dead load (D.L) of 500 kN, live load (L.L) of 200 kN, and moments (MDX = 50 kN.m, MLx = 60 kN.m, MDy = 30 kN.m, and MLx = 30 kN.m). The material properties are fc- = 25 MPa and fy = 400 MPa. Assuming d = 0.85h (d- = 63 mm), you can proceed with the design calculations.
1. Calculate the factored axial load (Pu) using the load combinations given in the code. For the given loads, the factored axial load can be calculated as follows:
Pu = 1.4D.L + 1.6L.L = 1.4(500 kN) + 1.6(200 kN) = 1200 kN
2. Calculate the factored moment (Mu) about the x-axis using the load combinations given in the code. For the given moments, the factored moment can be calculated as follows:
Mu = 1.2MDX + 1.6MLx = 1.2(50 kN.m) + 1.6(60 kN.m) = 168 kN.m
3. Calculate the factored moment (Mu) about the y-axis using the load combinations given in the code. For the given moments, the factored moment can be calculated as follows:
Mu = 1.2MDy + 1.6MLy = 1.2(30 kN.m) + 1.6(30 kN.m) = 84 kN.m
4. Determine the required area of the column (A) using the formula:
A = (Pu - 0.8Mu) / (0.4fc- + 0.67fy)
5. Substitute the values in the formula and solve for A:
A = (1200 kN - 0.8(168 kN.m)) / (0.4(25 MPa) + 0.67(400 MPa))
A = 1030 mm²
6. Calculate the dimensions of the rectangular column. Since d = 0.85h, we can solve for h and then calculate d:
A = bh
1030 mm² = bd
h = 1030 mm² / b
d = 0.85h
7. Substitute the value of h into the equation d = 0.85h and solve for d:
d = 0.85(1030 mm² / b)
By following these steps, you can design a rectangular column using Parme's method to resist the given loads and material properties.
Know more about axial load here:
https://brainly.com/question/33595099
#SPJ11
Question 6 What is the non-carbonate hardness of the water (in mg/L as CaCO3) with the following characteristics: Ca²130 mg/L as CaCO₂ Mg2-65 mg/L as CaCO3 CO₂-22 mg/L as CaCO3 HCO,134 mg/L as CaCO3 pH = 7.5 4 pts
The non-carbonate hardness of the water is 61 mg/L as CaCO₃.
To determine the non-carbonate hardness of the water, we need to subtract the carbonate hardness from the total hardness. The carbonate hardness can be calculated using the bicarbonate alkalinity, which is equivalent to the bicarbonate concentration (HCO₃⁻) in terms of calcium carbonate (CaCO₃).
Given:
Ca²⁺ concentration = 130 mg/L as CaCO₃
Mg²⁺ concentration = 65 mg/L as CaCO₃
CO₂ concentration = 22 mg/L as CaCO₃
HCO₃⁻ concentration = 134 mg/L as CaCO₃
The total hardness is the sum of the calcium and magnesium concentrations:
Total Hardness = Ca²⁺ concentration + Mg²⁺ concentration
Total Hardness = 130 mg/L + 65 mg/L
Total Hardness = 195 mg/L as CaCO₃
To calculate the carbonate hardness, we need to convert the bicarbonate concentration (HCO₃⁻) to calcium carbonate equivalents:
Bicarbonate Hardness = HCO₃⁻ concentration
Bicarbonate Hardness = 134 mg/L as CaCO₃
Now, we can calculate the non-carbonate hardness by subtracting the carbonate hardness from the total hardness:
Non-Carbonate Hardness = Total Hardness - Bicarbonate Hardness
Non-Carbonate Hardness = 195 mg/L - 134 mg/L
Non-Carbonate Hardness = 61 mg/L as CaCO₃
Therefore, the water's CaCO₃ non-carbonate hardness is 61 mg/L.
Learn more about alkalinity on:
https://brainly.com/question/30620768
#SPJ11