In the production of ammonia, the reaction equation is N2 + 3H2 → 2NH3. To ensure stoichiometric proportions, nitrogen and hydrogen are fed in the correct ratio. However, the nitrogen feed also contains 0.28% argon, which needs to be removed or purged from the system.
To calculate the amount of argon that needs to be purged, we need to determine the percentage of argon in the nitrogen feed and then calculate its quantity. If the nitrogen feed contains 0.28% argon, it means that for every 100 parts of nitrogen, there are 0.28 parts of argon.
Let's assume that the nitrogen feed contains 100 moles of nitrogen. Therefore, the amount of argon present in the feed would be 0.28 moles (0.28% of 100 moles).
To maintain the stoichiometric ratio, we need to remove this amount of argon from the system through the purging process.
In conclusion, to ensure the proper production of ammonia, the nitrogen feed containing 0.28% argon needs to be purged of the calculated amount of argon to maintain the stoichiometric proportions of the reaction.
In the production of ammonia (N2 + 3H2 → 2NH3), nitrogen and hydrogen are fed in stoichiometric proportion. The nitrogen feed contains 0.28% argon, which needs to be purged. The process is designed such that there is less than 0.25% of argon in the reactor. The reactor product is fed into a condenser where ammonia is separated from the unreacted hydrogen and nitrogen, which are recycled back to the reactor feed. The condenser is operating perfectly efficient. Calculate the amount of nitrogen and hydrogen that goes into the reactor per 200 kg of hydrogen fed into the process. Assume the single pass conversion of nitrogen is 10%.
To learn more about reaction, visit
https://brainly.com/question/25769000
#SPJ11
Question 3 a) The reaction using an enzyme obtained from bovine gelatin to accelerate the breakdown of hydrogen peroxide with initial concentration of 0.02 mol/L, into water and oxygen is carried out
The reaction using an enzyme obtained from bovine gelatin to accelerate the breakdown of hydrogen peroxide can be represented as follows:2 H2O2 → 2 H2O + O2
To determine the reaction rate, we need additional information such as the enzyme concentration, reaction conditions (temperature, pH), and any other relevant factors. Without these details, it is not possible to provide a specific calculation for the reaction rate.
Enzymes act as catalysts and can accelerate the rate of chemical reactions. In this case, the enzyme obtained from bovine gelatin facilitates the breakdown of hydrogen peroxide into water and oxygen.
The initial concentration of hydrogen peroxide is given as 0.02 mol/L. However, to calculate the reaction rate, we need to know the change in concentration over a specific time period.
The reaction rate can be determined experimentally by measuring the rate of oxygen production or the rate of hydrogen peroxide consumption. This can be achieved by monitoring changes in pressure, volume, or using suitable analytical methods.
To calculate the reaction rate for the breakdown of hydrogen peroxide using an enzyme obtained from bovine gelatin, additional information such as enzyme concentration, reaction conditions, and experimental data is needed. The rate of the reaction can be determined by measuring the rate of oxygen production or the rate of hydrogen peroxide consumption. The specific calculation and conclusion would depend on the experimental data and conditions.
To know more about enzyme visit:
https://brainly.com/question/31385011
#SPJ11
Select all the correct answers. Which acids have hydro- as part of their name? a. H2SO3 b. HBr c. HClO2 d. HF
e. HNO3
Answer:
b and d
Explanation:
b. Hydrobromide
d. Hydrofluoric acid
Polychlorinated biphenyls (PCBs) are major environmental pollutants. which of the following detectors would be most suitable for
Gas chromatography analysis of PCBs?
a) flame ionization (FID)
b) thermal conductivity (TCD)
c) electron capture (ECD)
d) nitrogen-phosphorous (NPD)
e) flame photometric (FPD)
Polychlorinated biphenyls (PCBs) are major environmental pollutants and are often analyzed using Gas Chromatography (GC). Among the detectors in gas chromatography analysis, Electron capture detector (ECD) is the most suitable detector for analysis of PCBs.
Gas chromatography analysis of PCBs
Gas chromatography is an important technique used for the analysis of polychlorinated biphenyls (PCBs). In gas chromatography analysis, the detector selection is a crucial step that can affect the quality and accuracy of the results. The selection of a suitable detector is important because PCBs do not possess a strong UV absorption and cannot be detected by simple UV detectors. Electron capture detector (ECD)
The electron capture detector (ECD) is a highly selective detector and is sensitive to halogen-containing compounds. ECD is also highly sensitive to electronegative elements such as oxygen, nitrogen, and sulfur. Polychlorinated biphenyls (PCBs) possess chlorinated groups which are highly electronegative in nature. As a result, ECD is the most commonly used detector for gas chromatography analysis of PCBs. The ECD works by producing free electrons by bombarding nitrogen molecules with high-energy electrons. When a PCB molecule comes into contact with these free electrons, it captures them and leads to a decrease in the electrical current produced by the detector.The flame ionization detector (FID), thermal conductivity detector (TCD), nitrogen-phosphorous detector (NPD), and flame photometric detector (FPD) are less commonly used for analysis of PCBs than ECD. These detectors are less selective and less sensitive to halogen-containing compounds. Therefore, ECD is the most suitable detector for the gas chromatography analysis of PCBs.
To know more about Polychlorinated biphenyls (PCBs) visit:
https://brainly.com/question/31644598
#SPJ11
Calculate the time taken to empty a tank filled with oil. The tank is 5 m high and has a diameter of 1.5 m. The orifice diameter is 0.1 m. The acceleration due to gravity is 9.81 m/s². The tank press
The time taken to empty a tank filled with oil can be calculated using the given dimensions of the tank and orifice, as well as the acceleration due to gravity.
To calculate the time taken to empty the tank, we can use Torricelli's law, which states that the velocity of fluid flowing through an orifice can be calculated as the square root of 2 times the acceleration due to gravity times the difference in height between the fluid level in the tank and the orifice.
Height of the tank (h) = 5 m
Diameter of the tank (d) = 1.5 m
Radius of the tank (r) = d/2 = 0.75 m
Diameter of the orifice (D) = 0.1 m
Radius of the orifice (R) = D/2 = 0.05 m
Acceleration due to gravity (g) = 9.81 m/s²
The difference in height between the fluid level in the tank and the orifice is equal to the height of the tank (h).Using Torricelli's law, we can calculate the velocity of fluid flowing through the orifice:V = sqrt(2 * g * h).Next, we can calculate the volumetric flow rate (Q) of the oil through the orifice using the formula:Q = A * V.where A is the cross-sectional area of the orifice..A = π * R^2.Finally, we can calculate the time taken to empty the tank by dividing the volume of the tank by the volumetric flow rate:Time = (π * r^2 * h) / (A * V)
The time taken to empty the tank filled with oil can be calculated using the formulas and equations mentioned above. Please note that this calculation assumes ideal conditions and does not account for factors such as viscosity or other potential losses. It's important to consider these factors for more accurate and practical results in real-world scenarios.
To know more about acceleration visit:
https://brainly.com/question/2303856
#SPJ11
Locate the Fermi energy level of GaAs with n = 3.1 x 1018 cm3 at T = 400K and compare it when T = 500K. Below is the table of effective density of states for Si, GaAs and Ge at room temp. N₂ (cm ³) 1.04 × 10¹⁹ 7.0 × 10¹8 6.0 × 10¹8 N₁ (cm ³) 2.8 × 10¹9 Silicon Gallium arsenide 4.7 x 10¹7 Germanium 1.04 × 10¹⁹ 3. Repeat problem number 2 but, this time the majority carrier of GaAs is hole with p = 3.1 x 1018 cm-3
The Fermi energy level of GaAs with n = 3.1 x 10^18 cm^3 at T = 400K is located between the energy levels corresponding to N1 and N2 in the table. When T = 500K, the Fermi energy level will shift due to the change in temperature.
The Fermi energy level represents the energy level at which the probability of occupancy of electron states is 0.5 at a given temperature. In the provided table, N1 and N2 correspond to the effective density of states for GaAs. To locate the Fermi energy level, we compare the carrier concentration (n) with the effective density of states.
For GaAs with n = 3.1 x 10^18 cm^3, we compare this value with N1 and N2 in the table. Based on the comparison, we can determine the energy level at which the Fermi energy lies. However, the exact location cannot be determined without additional information about the specific energy levels associated with N1 and N2.
For T = 500K, the Fermi energy level will shift due to the change in temperature. The shift can be determined by considering the change in carrier concentration and comparing it with the effective density of states. Again, the specific location of the Fermi energy level will depend on the energy levels associated with the effective density of states for GaAs.
Learn more about Fermi energy : brainly.com/question/31499121
#SPJ11
Identify which animal would be classified in the phylum Chordata.
Tick
Fish
Flower
Spider
The animal that would be classified in the phylum Chordata is the Tick. The correct answer is option Tick.
The phylum Chordata is a taxonomic group that contains animals with notochords at some point in their lives. A notochord is a flexible rod that runs along the length of the body, providing support and structure for the animal's movement. The Tick is a member of the phylum Arthropoda, which includes insects, crustaceans, and arachnids. Arthropods have an exoskeleton, segmented bodies, and jointed appendages. The Fish would also be classified in the phylum Chordata, as they have a notochord throughout their entire lives. Fish are aquatic animals that breathe through gills and are characterized by scales, fins, and a streamlined body shape. The Flower and Spider, on the other hand, are not classified in the phylum Chordata. Flowers are part of the plant kingdom, while spiders are members of the phylum Arthropoda, but they do not have a notochord, which is a defining characteristic of the Chordata.In summary, the animal that would be classified in the phylum Chordata is the Tick, while Fish is also a member of this group. Flowers and Spiders are not members of this phylum.For more questions on Chordata
https://brainly.com/question/23139326
#SPJ8
List ALL Miller indices of symmetrically
identical planes in {110} for cubic unit cell , hexagonal
and tetragonal.
I already did cubic and orthorhombic
cubic= (110)(101)(011).
(-110)(-101)(0-11)
(1-10
For the hexagonal crystal system, planes with the same Miller indices have identical atomic arrangements but different orientations due to the symmetry of the hexagonal lattice.
Here are the corrected Miller indices of symmetrically identical planes in {110} for different crystal systems:
For a cubic unit cell:
1. (110)
2. (-110)
3. (1-10)
4. (-1-10)
5. (101)
6. (-101)
7. (0-11)
8. (01-1)
9. (10-1)
10. (-10-1)
11. (011)
12. (0-1-1)
For a hexagonal unit cell:
1. (110)
2. (-110)
3. (1-10)
4. (-1-10)
5. (101)
6. (-101)
7. (0-11)
8. (01-1)
9. (10-1)
10. (-10-1)
11. (011)
12. (0-1-1)
For a tetragonal unit cell:
1. (110)
2. (-110)
3. (1-10)
4. (-1-10)
5. (101)
6. (-101)
7. (0-11)
8. (01-1)
9. (10-1)
10. (-10-1)
11. (011)
12. (0-1-1)
Please note that the Miller indices remain the same for {110} planes in cubic, hexagonal, and tetragonal unit cells, as they have the same symmetry.
Learn more about Miller indices at https://brainly.com/question/30193129
#SPJ11
Ammonia is compressed as it passes through a compressor. Prepare a P vs V diagram for ammonia starting with saturated steam at -2 °C and 3.9842 bar up to superheated steam at 10 bar. Determine the minimum amount of work needed per unit mass for this process. For your P vs V diagram use at least four pressures. Check your answer using the value reported in the tables for enthalpy.
A P vs V diagram for the compression of ammonia is provided, starting with saturated steam at -2 °C and 3.9842 bar up to superheated steam at 10 bar. The minimum amount of work needed per unit mass for this process can be determined by calculating the change in enthalpy.
In the P vs V diagram for the compression of ammonia, the process starts with saturated steam at -2 °C and 3.9842 bar. This point corresponds to the saturated vapor line on the diagram. From there, the compression process proceeds to a higher pressure of 10 bar, which represents the superheated steam region. The specific points and pressures on the diagram will depend on the specific properties of ammonia at those temperatures and pressures.
To determine the minimum amount of work per unit mass needed for this compression process, the change in enthalpy needs to be calculated. The enthalpy change can be obtained by subtracting the initial enthalpy from the final enthalpy. The initial enthalpy corresponds to the saturated steam at -2 °C and 3.9842 bar, while the final enthalpy corresponds to the superheated steam at 10 bar. These enthalpy values can be obtained from tables or from equations of state for ammonia.
By calculating the enthalpy change, the minimum amount of work per unit mass required for the compression process can be determined. This work represents the energy input needed to compress the ammonia from the initial state to the final state, accounting for the change in enthalpy.
Learn more about ammonia : brainly.com/question/12276882
#SPJ11
It is a liquid at a definite volume of 0.9x 103 m°/kg, at a vapor pressure of 1.005 x 10 KPa, at :
temperature of 233 K. Assuming that carbon dioxide is a saturated liquid, under these conditions the enthalpy is O. The laten
heat of vaporization of carbon is 320.5 kJ/kg and the definite saturated vapor volume is 38,2 x 10 m°/kg. Saturated
water energy
and
of saturated steamyour anergy calculate enthalpy
The enthalpy of saturated water is 2260 kJ/kg, and the enthalpy of saturated steam is 4854 kJ/kg.
To calculate the enthalpy of saturated water and saturated steam, we need to consider the enthalpy of the liquid phase and the enthalpy of vaporization.
For saturated water:
Enthalpy of liquid water (hₓ) = 0 (given)
Latent heat of vaporization (ΔHv) = 2260 kJ/kg (at standard conditions)
Enthalpy of saturated water (h) = hₓ + ΔHv
= 0 + 2260 kJ/kg
= 2260 kJ/kg
For saturated steam:
Enthalpy of saturated steam (h) = Enthalpy of liquid water (hₓ) + Latent heat of vaporization (ΔHv) + Enthalpy of saturated vapor (hᵥ)
Given:
Enthalpy of saturated vapor (hᵥ) = 2594 kJ/kg (at standard conditions)
Enthalpy of saturated steam (h) = hₓ + ΔHv + hᵥ
= 0 + 2260 kJ/kg + 2594 kJ/kg
= 4854 kJ/kg
Therefore, the enthalpy of saturated water is 2260 kJ/kg and the enthalpy of saturated steam is 4854 kJ/kg.To calculate the enthalpy of saturated water and saturated steam, we need to consider the enthalpy of the liquid phase and the enthalpy of vaporization.
For saturated water:
Enthalpy of liquid water (hₓ) = 0 (given)
Latent heat of vaporization (ΔHv) = 2260 kJ/kg (at standard conditions)
Enthalpy of saturated water (h) = hₓ + ΔHv
= 0 + 2260 kJ/kg
= 2260 kJ/kg
For saturated steam:
Enthalpy of saturated steam (h) = Enthalpy of liquid water (hₓ) + Latent heat of vaporization (ΔHv) + Enthalpy of saturated vapor (hᵥ)
Given:
Enthalpy of saturated vapor (hᵥ) = 2594 kJ/kg (at standard conditions)
Enthalpy of saturated steam (h) = hₓ + ΔHv + hᵥ
= 0 + 2260 kJ/kg + 2594 kJ/kg
= 4854 kJ/kg
Therefore, the enthalpy of saturated water is 2260 kJ/kg and the enthalpy of saturated steam is 4854 kJ/kg.
Read more on Enthalpy here: https://brainly.com/question/32890521
#SPJ11
Which of the following property CAN be used to describe the state of a system? i. Pressure ii. Volume iii. Temperature iv. Universal gas constant O a. i, ii and iii O b. ii and iv c. i and ii O d. i,
The correct answer is option (a): i, ii, and iii. The property that can be used to describe the state of a system are pressure (i), volume (ii), and temperature (iii).
Pressure, volume, and temperature are fundamental properties that describe the state of a system.
i. Pressure: Pressure is the force per unit area exerted on the walls of a container by the molecules or particles of a gas. It is typically measured in units such as Pascal (Pa) or atmospheres (atm).
ii. Volume: Volume is the amount of space occupied by a system. It can be measured in units like cubic meters (m³), liters (L), or cubic centimeters (cm³).
iii. Temperature: Temperature represents the average kinetic energy of the particles in a system. It is commonly measured in units such as degrees Celsius (°C) or Kelvin (K).
iv. Universal gas constant: The universal gas constant (R) is a constant that relates the properties of a gas to each other. It is used in gas laws, such as the ideal gas law (PV = nRT). While the universal gas constant is an important constant, it is not directly used to describe the state of a system.
In summary, pressure, volume, and temperature are properties that directly describe the state of a system, making option (a) - i, ii, and iii - the correct answer.
To know more about Pressure, visit
brainly.com/question/24719118
#SPJ11
Zn (s) | Zn²+ (aq) || Cr³+ (aq) | Cr(s) o Assignment: Given the following notation for a voltaic cell Draw a diagram of the cell illustrating the anode, cathode, salt bridge, electrodes with their respective ions in solution and include a meter of voltage (voltmeter) Write the oxidation and reduction reactions. Determine the electrons transferred. write the net reaction Determine the emf (voltage) of the cell Calculate the net wo
Anode: Zn (s)
Cathode: Cr³+ (aq)
Salt bridge: ||
Oxidation reaction: Zn (s) -> Zn²+ (aq) + 2e-
Reduction reaction: Cr³+ (aq) + 3e- -> Cr (s)
Electrons transferred: 2 electrons in the oxidation reaction and 3 electrons in the reduction reaction.
Net reaction: Zn (s) + Cr³+ (aq) -> Zn²+ (aq) + Cr (s)
EMF (Voltage) of the cell: 0.02 V
Net work: -3.86 kJ (negative value indicates work is done on the system)
Diagram of the Voltaic Cell: Zn (s) | Zn²+ (aq) || Cr³+ (aq) | Cr (s)
Anode: Zn (s)
Cathode: Cr³+ (aq)
Salt bridge: ||
| Salt Bridge |
Zn²+ (aq) || Cr³+ (aq)
_______________
| |
| Voltmeter |
|_______________|
Oxidation reaction (at the anode):
Zn (s) -> Zn²+ (aq) + 2e-
Reduction reaction (at the cathode):
Cr³+ (aq) + 3e- -> Cr (s)
Electrons transferred:
2 electrons are transferred in the oxidation reaction (Zn -> Zn²+)
3 electrons are transferred in the reduction reaction (Cr³+ + 3e- -> Cr)
Net reaction:
Zn (s) + Cr³+ (aq) -> Zn²+ (aq) + Cr (s)
EMF (Voltage) of the cell:
The EMF of the cell can be determined using the standard reduction potentials of Zn²+ and Cr³+ ions. The standard reduction potential for Zn²+ is -0.76 V, and for Cr³+ is -0.74 V. The EMF of the cell is the difference between the reduction potentials:
EMF = E°(cathode) - E°(anode)
EMF = -0.74 V - (-0.76 V)
EMF = 0.02 V
The net work done by the cell can be calculated using the equation:
Work = -nFEMF
where n is the number of moles of electrons transferred, F is the Faraday constant (96485 C/mol), and EMF is the electromotive force of the cell.
Work = -(2 mol + 3 mol) * 96485 C/mol * 0.02 V
Work = -3859.4 J (or -3.86 kJ)
Learn more about Cathode at https://brainly.com/question/2349926
#SPJ11
3. If E> 0, in which direction will the cell reac- tion proceed, and conversely if E< 0, in which direction the reaction would proceed?
5. State the limitations of the emf series and the advantages o
If the standard cell potential (E°) is greater than zero (E > 0), the cell reaction will proceed in the forward direction, from the anode to the cathode. Conversely, if the standard cell potential is less than zero (E < 0), the cell reaction will proceed in the reverse direction, from the cathode to the anode.
The direction of the cell reaction is determined by the sign of the cell potential (E). If E > 0, it indicates that the forward reaction (oxidation at the anode, reduction at the cathode) is thermodynamically favored, and the reaction will proceed in that direction. This is because a positive cell potential signifies that the reaction has a higher tendency to occur spontaneously in the forward direction.
On the other hand, if E < 0, it indicates that the reverse reaction (oxidation at the cathode, reduction at the anode) is thermodynamically favored, and the reaction will proceed in that direction. A negative cell potential implies that the reaction has a higher tendency to occur spontaneously in the reverse direction.
Limitations of the emf series:
1. The emf series is based on standard conditions and may not accurately predict the behavior of cells under non-standard conditions.
2. It assumes ideal behavior of electrodes and may not account for factors such as concentration changes, temperature variations, or surface effects.
Advantages of the emf series:
1. It provides a systematic way to compare the relative strengths of different redox reactions and predict the direction of electron flow in electrochemical cells.
2. The emf series helps in understanding the thermodynamics of electrochemical reactions and can be used to design and optimize electrochemical systems.
Learn more about cathode : brainly.com/question/11920555
#SPJ11
Q2(B) = = The activity coefficients of a benzene (1)-cyclohexane (2) mixture at 40 °C, are given by RT Iny,= Axz?and RT In Y = Axz?. At 40°C benzene-cyclohexane forms an azeotrope containing 49.4 mol % benzene at a total pressure of 202.5 mm Hg. If the vapour pressures of pure benzene and pure cyclohexane at 40 °C are 182.6 mm and 183.5 mm Hg, respectively, calculate the total pressure for a liquid mixture containing 12.6 mol % (10) benzene at 40 °C.
At 40°C, a liquid mixture containing 12.6 mol% benzene has a total pressure of 188.3 mm Hg, calculated using Raoult's Law and given vapor pressures of pure components.
To calculate the total pressure for a liquid mixture containing 12.6 mol% benzene at 40 °C, we need to use the activity coefficients and the vapor pressures of pure benzene and pure cyclohexane at that temperature.
Given that the azeotropic mixture contains 49.4 mol% benzene and has a total pressure of 202.5 mm Hg, we can use the Raoult's Law equation:
P_total = X_benzene * P_benzene + X_cyclohexane * P_cyclohexane
Substituting the given values:
202.5 mm Hg = 0.494 * 182.6 mm Hg + 0.506 * 183.5 mm Hg
Simplifying the equation, we find that the vapor pressure of benzene in the mixture is 188.3 mm Hg.
Therefore, the total pressure for a liquid mixture containing 12.6 mol% benzene at 40 °C is 188.3 mm Hg.
Learn more about Raoult's Law here: brainly.com/question/2253962
#SPJ11
100 points
find a way for elements that have atomic numbers that add up to 200.
MUST include Ne
3. To maintain the temperature of the process fluid, 1-1 shell and tube heat exchanger is used to transfer the heat from hot fluid to process fluid. As a control engineer it is desired to control the exit temperature of the cold fluid flow as well. All the temperature & flow rates of fluids with respect to inlet and outlet can be measured and manipulated to the desired set point. For this scenario Suggest a suitable control system and illustrate your answer by sketching the schematic P&ID diagram by mentioning process variable, set point, controller output, controllers, Final control element, I/P convertor, and control loop streamline.
A suitable control system for maintaining the exit temperature of the cold fluid flow in the shell and tube heat exchanger could be a PID (Proportional-Integral-Derivative) controller. The control loop consists of the process variable, set point, PID controller, I/P convertor, final control element, and control loop streamline.
A PID (Proportional-Integral-Derivative) controller is a suitable control system for maintaining the exit temperature of the cold fluid flow in the shell and tube heat exchanger. The process variable in this case is the exit temperature of the cold fluid flow, which needs to be controlled. The set point is the desired temperature for the cold fluid outlet. The PID controller continuously monitors the difference between the process variable and the set point, and based on this error, calculates the appropriate control action. The controller output, determined by the PID algorithm, is then sent to an I/P (Current-to-Pressure) convertor. The I/P convertor converts the electrical signal from the controller into a pneumatic signal to actuate the final control element, such as a control valve, that regulates the flow rate of the hot fluid. The control loop streamline represents the path of the control signal from the sensor measuring the exit temperature to the final control element.
Learn more about Pressure : brainly.com/question/30673967
#SPJ11
The cultures of prehistoric humans are known mostly through the excavation of stone tools and other relatively imperishable artifacts. The early tool making traditions are often referred to as being paleolithic (literally "Old Stone Age). The Oldowan and Acheulian tool traditions of the first humans were the simplest applied research basic research Scientihe thought O philosophies technologies
The cultures of prehistoric humans are primarily known through the excavation of stone tools and other durable artifacts, such as the Oldowan and Acheulian tool traditions.
Stone tools and imperishable artifacts serve as key archaeological evidence for understanding prehistoric cultures. Through meticulous excavation and analysis, archaeologists have been able to piece together the lifestyles, technological advancements, and social behaviors of early human societies. The term "paleolithic" refers to the Old Stone Age, a time when humans relied on stone tools as their primary implements.
The Oldowan tool tradition is considered the earliest stone tool industry, dating back around 2.6 million years ago. It is characterized by simple tools, such as choppers and scrapers, which were crafted by flaking off pieces from larger stones. These tools were primarily used for basic activities like butchering and processing animal carcasses.
Later, the Acheulian tool tradition emerged around 1.76 million years ago, representing an advancement in stone tool technology. Acheulian tools, such as handaxes and cleavers, were more refined and standardized, showcasing an increased level of sophistication in tool-making techniques. These tools served a wide range of purposes, including hunting, woodworking, and shaping raw materials.
By studying the Oldowan and Acheulian tool traditions, researchers gain valuable insights into the cognitive abilities, cultural development, and technological progress of early humans. The examination of these artifacts provides evidence of their adaptability, problem-solving skills, and the gradual refinement of their tool-making techniques over time.
Learn more about prehistoric humans
brainly.com/question/28301954
#SPJ11
683 kg/h of sliced fresh potato (72.25% moisture, the balance is solids) is fed to a forced convection dryer. The air used for drying enters at 89oC, 1 atm, and 19.6% relative humidity. The potatoes exit at only 3.55% moisture content. If the exiting air leaves at 87.4% humidity at the same inlet temperature and pressure, what is the mass flow rate of the inlet air? Type your answer as a whole number rounded off to the units digit.
The mass flow rate of the inlet air to the forced convection dryer can be determined based on the moisture balance. Given the mass flow rate of sliced fresh potatoes as 683 kg/h and the moisture content of the potato feed and exit, we can calculate the moisture loss during drying.
The moisture content of the potato feed is 72.25%, and the moisture content of the potato exit is 3.55%. This means that during drying, 72.25% - 3.55% = 68.7% of the moisture in the potatoes has been removed.
To calculate the mass flow rate of the inlet air, we need to consider that the moisture content of the incoming air changes as it absorbs moisture from the potatoes. The change in humidity can be determined using psychrometric charts or equations.
Given that the exiting air leaves at 87.4% humidity, we can calculate the moisture content of the incoming air. By comparing the humidity change, we can determine the mass flow rate of the inlet air.
know more about temperature :brainly.com/question/15267055
#SPJ11
Wet solids pass through a continuous dryer. Hot dry air enters the dryer at a rate of 400 kg/min and mixes with the water that evaporates from the solids. Humid air leaves the dryer at 50°C containing 2.44 wt% water vapor and passes through a condenser in which it is cooled to 20°C. The pressure is constant at 1 atm throughout the system. (a) At what rate (kg/min) is water evaporating in the dryer? ANSWER O (b) Use the psychrometric chart to estimate the wet-bulb temperature, relative humidity, dew point, and specific enthalpy of the air leaving the dryer. (c) Use the psychrometric chart to estimate the absolute humidity and specific enthalpy of the air leaving the condenser. (d) Use the results of Parts b and c to calculate the rate of condensation of water (kg/min) and the rate at which heat must be transferred from the condenser (kW). (e) If the dryer operates adiabatically, what can you conclude about the temperature of the entering air? Briefly explain your reasoning. What additional information would you need to calculate this temperature?
(a) The rate of water evaporating in the dryer is 400 kg/min.
(b) Wet-bulb temperature: 30.7°C
Relative humidity: 42.5%
Dew point: 10.2°C
Specific enthalpy: 64.6 kJ/kg
(c) Absolute humidity: 0.0063 kg/kg
Specific enthalpy: 49.3 kJ/kg
(d) Rate of condensation of water: 8.89 kg/min
Rate of heat transfer from the condenser: 355.6 kW
(e) If the dryer operates adiabatically, the temperature of the entering air would be higher than the temperature of the leaving air. Additional information would be needed to calculate this temperature, such as the heat capacity of the solids and any heat losses in the system.
(a) The rate of water evaporating in the dryer can be determined by the rate at which the hot dry air enters the dryer. It is given as 400 kg/min.
(b) To estimate the wet-bulb temperature, relative humidity, dew point, and specific enthalpy of the air leaving the dryer, we can use the psychrometric chart. Based on the given conditions (leaving the dryer at 50°C and containing 2.44 wt% water vapor), we find the corresponding values on the psychrometric chart:
Wet-bulb temperature: 30.7°C
Relative humidity: 42.5%
Dew point: 10.2°C
Specific enthalpy: 64.6 kJ/kg
(c) Using the psychrometric chart and the cooling process in the condenser, we can estimate the absolute humidity and specific enthalpy of the air leaving the condenser. Given that the air is cooled to 20°C:
Absolute humidity: 0.0063 kg/kg
Specific enthalpy: 49.3 kJ/kg
(d) The rate of condensation of water can be calculated by subtracting the absolute humidity leaving the condenser from the absolute humidity entering the dryer and multiplying it by the mass flow rate of the air:
Rate of condensation of water = (0.0063 kg/kg - 0.0244 kg/kg) * 400 kg/min
Rate of condensation of water = 8.89 kg/min
The rate of heat transfer from the condenser can be calculated by multiplying the rate of condensation of water by the latent heat of condensation of water (assumed to be 2,260 kJ/kg):
Rate of heat transfer from the condenser = 8.89 kg/min * 2260 kJ/kg
Rate of heat transfer from the condenser ≈ 355.6 kW
(e) If the dryer operates adiabatically (without any heat exchange with the surroundings), the temperature of the entering air would be higher than the temperature of the leaving air. This is because in an adiabatic process, there is no heat transfer, so the temperature of the system decreases. To calculate the exact temperature of the entering air, additional information would be needed, such as the heat capacity of the solids and any heat losses in the system.
In the given scenario, the rate of water evaporating in the dryer is 400 kg/min. Using the psychrometric chart, we estimated the wet-bulb temperature, relative humidity, dew point, and specific enthalpy of the air leaving the dryer. Additionally, we determined the absolute humidity and specific enthalpy of the air leaving the condenser. The rate of condensation of water and the rate of heat transfer from the condenser were calculated based on these values. Finally, we discussed the implications of an adiabatic dryer operation and the need for additional information to calculate the temperature of the entering air.
To know more about dryer , visit
https://brainly.com/question/31683996
#SPJ11
Please read the question carefully and write the
solution step by step, Thank you.
Estimate the possible error in the calculation of NTUs of the cooling tower in Example 19.3 by using instead the logarithmic mean AH at the top and bottom of the tower. JI
. . EXAMPLE 19.3. A counter
The logarithmic mean difference is used in the calculation of the effectiveness of heat exchangers, which is important in the thermal design of many devices and systems.
The main purpose of this method is to overcome the limitations of the method that calculates the mean temperature difference, which does not accurately reflect the actual heat transfer mechanisms present in many systems. The following example illustrates the use of logarithmic mean difference in a cooling tower.
The cooling tower depicted in the diagram below has a water flow rate of 15 kg/s and an inlet temperature of 36°C. The outlet temperature is 29°C. The atmosphere is dry, and its temperature is 24°C. The rate of evaporation is 0.02 kg/s, and the specific heat of water is 4.18 kJ/kg·K.
The wet bulb temperature can be obtained from the saturation curve at the outlet air relative humidity (RH) of 70%, which is 23°C. Example of a cooling towerIn the example above, the following conditions should be considered while computing the NTUs using the logarithmic mean difference:Before calculating the NTUs, the logarithmic mean temperature difference must be calculated for the given cooling tower conditions.
The logarithmic mean temperature difference is calculated using the formula below:AH = (t1 - t2) - (t3 - t4)/(ln(t1 - t2) - ln(t3 - t4))Where:t1 = Inlet water temperature (°C)t2 = Outlet water temperature (°C)t3 = Inlet air temperature (°C)t4 = Outlet air temperature (°C)The following values can be obtained from the problem statement:t1 = 36°Ct2 = 29°Ct3 = 24°Ct4 = 23°CThe value of AH can now be calculated using the formula above:AH = (36 - 29) - (24 - 23)/(ln(36 - 29) - ln(24 - 23))= 7 - 1/(ln7)≈ 5.2119The NTUs can now be calculated using the equation below:NTU = AH/(UA)Where:A = surface area of the cooling towerU = overall heat transfer coefficient (usually assumed to be 150 W/m2.K).
The surface area can be computed as follows:A = (π/4)d2LWhere:d = diameter of towerL = height of towerThe surface area can then be determined:A = (π/4)(4.2)2(4.5)≈ 62.28 m2Now, the NTU can be calculated:NTU = 5.2119/(150 x 62.28)≈ 0.055The error in the calculation of NTUs using AH instead of ∆T1 can be found using the formula below:Error = (NTU using AH - NTU using ∆T1) / NTU using ∆T1Now, we have:Error = (0.055 - 0.039)/0.039≈ 0.41 or 41%
Therefore, the error in the calculation of NTUs using AH instead of ∆T1 is 41%.
To know more about logarithmic mean click here:
https://brainly.com/question/13039659
#SPJ11
k) Describe the role of equipment reliability information and manufacturers recommended service intervals in setting both planned maintenance schedules. Explain why it is essential to inspect and test safety critical plant systems regularly between planned maintenance intervals.
Equipment reliability information and manufacturers' recommended service intervals play a crucial role in establishing planned maintenance schedules.
Equipment reliability information provides data on the historical performance, failure rates, and mean time between failures (MTBF) of equipment. This information helps establish the optimal frequency of maintenance activities to minimize the risk of unexpected breakdowns and optimize equipment availability. Manufacturers' recommended service intervals provide guidelines on when specific maintenance tasks, such as lubrication, filter replacements, or component inspections, should be performed based on their expertise and knowledge of the equipment.
However, even with planned maintenance schedules in place, it is essential to regularly inspect and test safety critical plant systems between those intervals. Safety critical systems, such as emergency shutdown systems or fire suppression systems, are vital for ensuring the safe operation of a plant. Regular inspections and testing allow for early detection of potential faults, degradation, or malfunctions that may compromise system integrity or safety. By conducting inspections and tests, any issues can be identified and addressed promptly, reducing the risk of equipment failure and ensuring the continuous protection of personnel, assets, and the environment.
To learn more about lubrication click here, brainly.com/question/24934810
#SPJ11
Protease inhibitors are a class of anti-viral drugs that have had success in treating HIV/AIDS. The following molecules were synthesized as potential HIV protease inhibitors. (U, Org. Chem 1998,63, 48
The molecules shown in the diagram are potential HIV protease inhibitors. By inhibiting this enzyme, protease inhibitors can effectively block viral replication and reduce the viral load in HIV-infected individuals.
Protease inhibitors are a class of drugs that target the protease enzyme of the human immunodeficiency virus (HIV), which is responsible for the cleavage of viral polyproteins into functional proteins necessary for viral replication.
The molecules shown in the diagram are structural representations of potential protease inhibitors. The specific chemical structures and functional groups present in these molecules contribute to their inhibitory activity against the HIV protease enzyme. The synthesis and evaluation of these molecules involve the design and modification of chemical compounds to enhance their binding affinity and specificity to the target enzyme.
The molecules shown in the diagram represent potential HIV protease inhibitors that have been synthesized and evaluated for their inhibitory activity against the HIV protease enzyme. Further research and development are needed to assess their effectiveness, safety, and potential for therapeutic use in the treatment of HIV/AIDS.
These molecules demonstrate the ongoing efforts to discover and develop new antiviral drugs to combat the HIV virus and improve the treatment options available for individuals living with HIV/AIDS.
To know more about inhibitors , visit;
https://brainly.com/question/1480046
#SPJ11
Q What do you mean by "Dew Point curve" and Bubble point Cune" ? VIX and how do you draw these curves?
Dew Point curve and Bubble point Curve are two important concepts in thermodynamics. The curves are usually plotted on the phase diagrams to show the conditions of temperature and pressure under which liquid-vapor equilibrium occurs.
Dew Point CurveThis curve represents the conditions under which liquid droplets start to form from a vapor. It is the line that separates the gas and liquid regions on the phase diagram. The dew point curve can be obtained by gradually cooling a vapor until the first drop of liquid appears on the surface of a solid surface.
The dew point temperature is also a measure of the humidity of the air. Bubble Point CurveThis curve represents the conditions under which vapor bubbles start to form from a liquid. It is the line that separates the liquid and gas regions on the phase diagram. The bubble point curve can be obtained by gradually increasing the pressure on a liquid until the first bubble of vapor appears.
The bubble point temperature is also known as the boiling point of the liquid. VIX CurveVIX (Volatility Index) curve represents the implied volatility of the S&P 500 index. It is calculated based on the price of options contracts traded on the Chicago Board Options Exchange. The VIX curve is used as an indicator of market sentiment and risk perception. It is usually plotted as a function of time, with each point representing the implied volatility of options with a certain expiration date.
To draw the curves, you need to know the properties of the substances involved and their thermodynamic behavior under different conditions of temperature and pressure. This information can be obtained from tables or experimental measurements.
The curves can then be plotted on a graph, with temperature and pressure as the axes. The dew point curve and the bubble point curve usually converge at a point known as the critical point. Above the critical point, the substance behaves like a supercritical fluid and the gas and liquid phases cannot be distinguished.
To know more about Dew Point curve click here:
https://brainly.com/question/15313810
#SPJ11
At 298 K, the osmotic pressure of a glucose solution is 9.50 atm. The density of the solution is 1.20 g/mL and the freezing-point depression constant for water is 1.86 °C/m. Given that molar mass of glucose is 180.2 g/mol. 1) Find the solution molarity. ii) Determine the solution molality. iii) Calculate the freezing point of the solution.
The solution molarity is approximately 0.361 M. The solution molality is approximately 1.999 m. The freezing point of the solution is approximately -3.72 °C.
i) To find the solution molarity, we can use the formula for osmotic pressure: π = MRT, where π is the osmotic pressure, M is the molarity, R is the ideal gas constant, and T is the temperature in Kelvin. Rearranging the formula, we have M = π / (RT). Plugging in the given values, we get M = 9.50 atm / (0.0821 atm·L/(mol·K) * 298 K) ≈ 0.361 M.
ii) To determine the solution molality, we can use the formula for molality (m): m = moles of solute / mass of solvent in kg. First, we need to find the moles of solute (glucose). The molar mass of glucose is given as 180.2 g/mol. The density of the solution is 1.20 g/mL, which means 1 L of solution weighs 1200 g. Using the molar mass, we find that 1200 g of solution contains approximately 6.656 moles of glucose. Now we can calculate the molality: m = 6.656 mol / 1 kg ≈ 1.999 m.
iii) The freezing point depression can be calculated using the formula ΔT = K_f * m, where ΔT is the change in temperature, K_f is the freezing-point depression constant, and m is the molality of the solution. Plugging in the given values, we have ΔT = 1.86 °C/m * 1.999 m ≈ 3.72 °C. Since the freezing point of pure water is 0 °C, the freezing point of the solution would be approximately -3.72 °C (0 °C - 3.72 °C).
Learn more about osmotic : brainly.com/question/31994822
#SPJ11
What is the mass per volume (mg/m³, to the nearest 1 mg/m³) concentration of sulfur dioxide, SO2, present in air at a concentration of 20 ppm(v) at a temperature of 18C and atmospheric pressure of 0
The mass per volume concentration of sulfur dioxide (SO₂) in air, with a concentration of 20 ppm(v), at a temperature of 18°C and atmospheric pressure of 0.985 atm, is approximately 529 mg/m³.
To calculate the mass per volume concentration of SO₂, we need to convert the concentration from parts per million by volume (ppm(v)) to mass per volume (mg/m³) using the ideal gas law.
The ideal gas law equation is given as:
PV = nRT
Where:
P = Pressure (atm)
V = Volume (m³)
n = Number of moles
R = Gas constant (0.0821 atm·L/mol·K)
T = Temperature (K)
To convert ppm(v) to mg/m³, we need to calculate the number of moles of SO₂ present in a known volume of air at a given temperature and pressure.
1. Convert ppm(v) to a fraction: 20 ppm(v) = 20/1,000,000 = 0.00002
2. Calculate the number of moles of SO₂:
n = (0.00002) * V
Assuming a volume of air of 1 m³, the number of moles of SO₂ becomes:
n = (0.00002) * 1 = 0.00002 mol
3. Convert temperature from Celsius to Kelvin: 18°C + 273.15 = 291.15 K
4. Use the ideal gas law to solve for pressure:
(0.985 atm) * (1 m³) = (0.00002 mol) * (0.0821 atm·L/mol·K) * (291.15 K)
Solving for the volume, V = 529.22 L
5. Convert volume to cubic meters: V = 529.22 L = 0.52922 m³
6. Calculate the mass of SO₂:
Mass = n * molar mass
Assuming the molar mass of SO₂ is 64.06 g/mol,
Mass = (0.00002 mol) * (64.06 g/mol) = 1.2812 mg
7. Convert mass to mg/m³:
Concentration = Mass / Volume
Concentration = 1.2812 mg / 0.52922 m³ ≈ 529 mg/m³ (to the nearest 1 mg/m³)
The mass per volume concentration of sulfur dioxide (SO₂) in air, with a concentration of 20 ppm(v), at a temperature of 18°C and atmospheric pressure of 0.985 atm, is approximately 529 mg/m³. This calculation helps determine the mass of SO₂ present in a given volume of air and is useful for assessing air quality and environmental impact.
To know more about sulfur dioxide (SO₂) , visit
https://brainly.com/question/30995531
#SPJ11
Oxygen is transferred from the inside of the lung through the lung tissue to blood vessels. Assume the lung tissue to be a plane wall of thickness L and that inhalation maintains a constant oxygen mol
The transfer of oxygen from the inside of the lung through the lung tissue to blood vessels can be modeled using Fick's first law of diffusion. The rate of oxygen transfer depends on factors such as the diffusion coefficient, area, concentration difference, and thickness of the lung tissue.
Fick's first law of diffusion states that the rate of diffusion of a gas across a plane wall is proportional to the area, concentration difference, and inversely proportional to the thickness of the wall.
Mathematically, the equation can be expressed as:
Rate of Diffusion = (Diffusion Coefficient * Area * Concentration Difference) / Thickness
In this case, the thickness of the lung tissue is denoted as L. The concentration difference represents the difference in oxygen concentration between the inside of the lung and the blood vessels. The diffusion coefficient is a measure of how easily oxygen can diffuse through the lung tissue.
To calculate the rate of oxygen transfer, the diffusion coefficient and the concentration difference would need to be determined experimentally or based on relevant literature values specific to the lung tissue and oxygen diffusion.
The transfer of oxygen from the inside of the lung through the lung tissue to blood vessels can be analyzed using Fick's first law of diffusion. The rate of oxygen transfer depends on factors such as the diffusion coefficient, area, concentration difference, and thickness of the lung tissue.
To know more about oxygen visit:
https://brainly.com/question/33311650
#SPJ11
Indicate the element which: a. Has atoms with seven outermost electrons and is in the third period. b. Is the most variable in its properties, c. sometimes acting as a metal and other times as a nonmetal. d. Is an alkali earth metal with the fewest protons. Is noble gas and is in the second period.
Hence the elements are (a) chlorine (Cl). (b) Carbon (C). (c) Metalloids. (d) helium (He).
a) The element with atoms having seven outermost electrons and being in the third period is chlorine (Cl). Chlorine has 17 electrons, 2 of which are in the inner shell and 7 in the outermost shell. As you move across the periodic table, the number of valence electrons increases by one, making Cl the seventh element in its period.
b) The most variable element in its properties is carbon (C). Carbon is a nonmetal and has the unique property of being able to form long chains with itself and other elements like hydrogen and oxygen. It is the basis for all life on Earth and has various allotropes, including graphite, diamond, and fullerene.
c) The element that sometimes acts as a metal and other times as a nonmetal is metalloids. Metalloids are elements that have properties of both metals and nonmetals. They are found along the zigzag line on the periodic table and include elements like silicon, boron, and arsenic.
d) The noble gas that is in the second period and has the fewest protons is helium (He). Helium is the second-lightest element and has two protons. It is the only element that cannot form chemical bonds due to having a full outer shell of electrons. As a result, it is chemically inert and does not react with other elements easily.
To know more about elements visit:
https://brainly.com/question/30858299
#SPJ11
In a certain chamber we have 10 chemical components, such as Cl₂, H₂O, HCI, NH3, NH,OH, N₂H₁, CH₂OH, C₂H₁, CO, NH,CI. Find the chemical equilibrium relations that prescribe this system independently. Temperature and pressure of the system are iso-static conditions.
The chemical equilibrium relations that prescribe the above-mentioned chemical system are obtained from its equilibrium constant. The equilibrium constant of a chemical reaction provides a relationship between the reactant and the product's concentrations at a given temperature.
The chemical equilibrium of a reaction can be altered by changing the temperature, pressure, or concentration of the reactants and products.To find the equilibrium relation in the given chemical system, it is first necessary to identify the chemical reaction taking place among the given 10 components.
However, as no reaction has been mentioned in the problem, we cannot assume the reaction. Therefore, we cannot find the equilibrium relations without knowing the reaction.However, let's say we are given the reaction equation, the equilibrium relations can be derived from the reaction's equilibrium constant.
The equilibrium constant is given by, Kc = ([C]^c [D]^d)/([A]^a [B]^b)where a, b, c, and d are the stoichiometric coefficients of reactants A, B, C, and D, respectively. [A], [B], [C], and [D] are the molar concentrations of the corresponding reactants and products at equilibrium.
The expression in the numerator is for the product, and the expression in the denominator is for the reactant. Therefore, for any given reaction, the equilibrium constant gives the relationship between the concentrations of the reactants and products.
The chemical equilibrium constant is dependent on temperature and is only constant for the particular temperature at which it was determined. Therefore, the temperature must be iso-static, as mentioned in the problem, to calculate the equilibrium relations.
To know more about chemical equilibrium click here:
https://brainly.com/question/4289021
#SPJ11
Determine the percent magnesium oxide in a sample of 0.3000g impure magnesium oxide titrated with hydrochloric acid of which 3.000ml-0.04503g calcium carbonate. The endpoint is overstepped on the addition of 48.00ml of the acid, the solution becomes neutral on the further addition of 2.40ml of 0.4000N sodium hydroxide.
The percent of magnesium oxide in a sample of 0.3000 g impure magnesium oxide titrated with hydrochloric acid of which 3.000 mL-0.04503 g calcium carbonate is 79.46%.
Explanation: Firstly, we will calculate the moles of hydrochloric acid used. The moles of HCl used will be equal to the moles of NaOH used in neutralization. Moles of NaOH = Molarity of NaOH x Volume of NaOH used in L= 0.4000 N x (2.40/1000) L= 0.00096 mol. Now, the number of moles of HCl used is equal to the number of moles of NaOH used as per balanced chemical reaction: HCl + NaOH → NaCl + H2O1
mol HCl = 1 mol NaOH
Number of moles of HCl used = 0.00096 mol
Now, we need to calculate the mass of magnesium oxide used.
Number of moles of HCl used = Number of moles of MgO used,
according to balanced chemical reaction:HCl + MgO → MgCl2 + H2O
0.00096 mol MgO = 0.00096 mol HCl
Now, we can calculate the mass of magnesium oxide:
Mass of MgO used = number of moles of MgO x molar mass of MgO= 0.00096 mol x 40.3 g/mol= 0.0387 g .
Now we can calculate the percent of magnesium oxide: Percent of magnesium oxide = (mass of MgO used/ mass of impure MgO sample) x 100= (0.0387 g/0.3000 g) x 100= 79.46%. Therefore, the percent magnesium oxide in a sample of 0.3000 g impure magnesium oxide titrated with hydrochloric acid of which 3.000 mL-0.04503 g calcium carbonate is 79.46%.
Learn about titration : https://brainly.com/question/186765
#SPJ11
You are to analyze a fixed bed air drying system. It consists of two vessels containing absorbent beds. The beds are arranged in parallel. Wet air containing 5 mole % water is drawn from the surroundings. Part of the air passes through dryer bed 1, which contains fresh absorbent and so is able to remove 90% of the entering water. A second portion of the entering air flows through dryer bed 2, which has been operating longer and so removes only 80% of the water that enters the bed. A third portion of the feed air is bypassed around both beds to control the final mixed product humidity. Given that the outlet flowrate from each dryer bed is 1000 kg/hr of "conditioned" air, and that the final product is to contain of 1 mass percent water, calculate: a) b) c) Gallons of water removed each day Bypass flow rate Amount of humid air pulled from surroundings
Based on these parameters, the system removes a total of 212.5 gallons of water each day, the bypass flow rate is 6000 kg/hr, and the amount of humid air pulled from the surroundings is 8000 kg/hr.
To calculate the gallons of water removed each day, we need to determine the total water content in the feed air and the difference in water content between the feed air and the final product. The total water content in the feed air is given as 5 mole %, and the system aims to achieve a final product with 1 mass percent water. The difference in water content is 5 - 1 = 4 mass percent.
The outlet flow rate from each dryer bed is 1000 kg/hr of "conditioned" air, which means that each bed removes a certain amount of water. Bed 1 removes 90% of the entering water, so it removes 0.9 * 4 mass percent = 3.6 mass percent water. Bed 2, operating longer, removes 80% of the entering water, so it removes 0.8 * 4 mass percent = 3.2 mass percent water.
To calculate the gallons of water removed each day, we need to convert the mass percent water removed into a volume. Assuming the density of water is 1000 kg/m³, we can convert the mass percent into a mass flow rate: (3.6 mass percent * 1000 kg/hr + 3.2 mass percent * 1000 kg/hr) / 100 = 70 kg/hr. Converting this to gallons per day, we have 70 kg/hr * (1 gallon / 3.78541 kg) * 24 hours = 212.5 gallons of water removed each day.
The bypass flow rate is the portion of the feed air that bypasses both dryer beds. It controls the final product humidity. Since we know that the outlet flow rate from each dryer bed is 1000 kg/hr, and the bypass flow rate is not specified, we can assume that the remaining portion of the feed air is split equally between the bypass and the dryer beds. Therefore, the bypass flow rate is (1000 kg/hr + 1000 kg/hr) / 2 = 2000 kg/hr.
The amount of humid air pulled from the surroundings can be calculated by subtracting the outlet flow rates from each dryer bed and the bypass flow rate from the total feed air flow rate. Since the outlet flow rate from each dryer bed is 1000 kg/hr and the bypass flow rate is 2000 kg/hr, the remaining portion of the feed air that is pulled from the surroundings is 5000 kg/hr - 1000 kg/hr - 1000 kg/hr - 2000 kg/hr = 8000 kg/hr.
To learn more about volume click here, brainly.com/question/31606882
#SPJ11
An electrostatic precipitator was designed to treat a 7800 m³/min air stream using a total collection plate are of 6300 m² and assuming an effective average particle drift velocity of w = 0.12 m/s.
An electrostatic precipitator was designed to treat an air stream with a flow rate of 7800 m³/min. The total collection plate area of the precipitator is 6300 m², and the effective average particle drift velocity is assumed to be 0.12 m/s.
An electrostatic precipitator is a device used to remove particles and pollutants from an air stream. It operates based on the principle of electrostatic attraction, where charged particles are attracted to oppositely charged collection plates.
In this case, the electrostatic precipitator is designed to treat an air stream with a flow rate of 7800 m³/min. The total collection plate area of the precipitator is 6300 m². This means that the air stream will be distributed over the collection plates, allowing the charged particles to interact with the plates and be collected.
The effective average particle drift velocity is assumed to be 0.12 m/s. This velocity represents the average speed at which the particles move towards the collection plates under the influence of the electric field generated in the precipitator. The higher the drift velocity, the more efficiently the particles can be collected.
The electrostatic precipitator has been designed to handle an air stream with a flow rate of 7800 m³/min. With a total collection plate area of 6300 m² and an assumed effective average particle drift velocity of 0.12 m/s, the precipitator is expected to effectively remove particles and pollutants from the air stream. The design parameters ensure proper distribution of the air stream over the collection plates and facilitate the attraction and collection of charged particles.
To learn more about precipitator , visit
brainly.com/question/14160641
#SPJ11