It is required that the resultant force acting on the eyebolt in Fig (a) be directed along the positive x axis and that F2 have a minimum magnitude. Determine this magnitude, the angle θ, and the corresponding resultant force

Answer:

The GMAW process commonly uses a constant voltage power source (GMAW-CV) that allows for a relatively constant welding voltage output over a range of welding currents. For GMAW-CV the welder selects the wire feed speed (WFS) on the wire feeder unit and an appropriate voltage on the welding power supply.

Answer: i believe it’s acoustics

Explanation:

Answer: hello the diagram related to your question is missing please the third image is the missing part of the question

Fx = 977.76 Ib/ft

Explanation:

Estimate the force that water exerts on the pier

V = 12 ft/s

D( diameter ) = 6 ft

first express the force  on the first half of the cylinder  as

Fx1 =  - [tex]-2\int\limits^\pi _\frac{\pi }{2} {Ps*cos\beta *a} \, d\beta[/tex]   ---------------- ( 1 )

where ; Fy = 0

Ps = Po + 1/2 Pv^2 ( 1 - 4 sin^2β )  ------------- ( 2 )

Input equation (2)  into equation ( 1 )         (note :  assuming Po = 0 )

attached below is the remaining part of the solution

Answer:

A

Explanation:

Answer: https://www.careerbuilder.com/advice/what-are-problemsolving-skills-and-why-are-they-important

Explanation:

please if this helps give me brainlest it is about career builder

Answer:

ok

Explanation:

Answer:

yeah you will have it sir

Answer:

Explanation:

Brake systems are most likely to fail at the ends.  One of the most common problems is a trailer lighting splitter is left on. With time and usage, the fuse can blow interrupting the signal path from the switch to the bulb.

Answered by the ONE & ONLY #QUEEN aka #DRIPPQUEENMO

HOPE THIS HELPED!!!

Answer:

with turbo or nos

Explanation:

Answer:                      

Explanation:

Answer: C. Voltage

Explanation:

Here are some other words as well.

potential, voltage, potential drop, potential difference.

Answered by the ONE & ONLY #QUEEN aka #DRIPPQUEENMO!!!

HOPE THIS HELPED!!!

Answer:

2nd one

Explanation:

on edge 21

The option that identifies the engineer should choose the reverse engineering process in the following scenario is there will be changes to the existing product. The correct option is b.

The distinction between the reverse engineering process and the engineering design process is quite slight. The engineering design process is a method that requires months of planning and design in order to provide a blueprint for a specific project.

The fundamental skill of learning to make something by working backward from an existing inspiration for your project is called reverse engineering.

Three contrasts are that the engineering design process is based more on mental and written learning than it is on physical learning (unlike the reverse engineering process).

Therefore, the correct option is b, There will be changes to the existing product.

To learn more about reverse engineering, refer to the link:

https://brainly.com/question/10175918

#SPJ2

Answer:

Look at the load capacity chart in the cab

Explanation:

A crane can be defined as a large, tall metallic machine or equipment that is designed with a long horizontal arm (jib) used for the lifting and movement of very heavy objects through the air. They're usually designed to be operated by a human operator, who typically uses a remote controller and a beam to control the direction of movement of the crane.

Due to the fact that cranes are used for lifting and moving very heavy objects, they are powered by an internal combustion engine and electric motors.

Furthermore, all cranes have the maximum capacity of load they're able to lift at a particular point in time. In order to determine the rated or gross capacity of a crane and maintain safe operation, it is important to check its load capacity chart. The actual load a crane can lift is its net capacity and it must not be exceeded at any time, so as to avoid structural failure or overturning of the crane.

Hence, the best way to find the load capacity of a crane is to look at the load capacity chart in the cab.

The load can include rigging components, hooks, blocks, and other lifting equipment that is considered part of the load. The maximum load capacity of the crane is about 18 metric tons.

Hence the option C look at the chart is correct.

Learn more about the way to find the load capacity of a crane.

brainly.com/question/25884809.

Answer:

Resistance = 3 Ω

Explanation:

As we know that, By Ohm's Law

V = IR

where

V is the voltage in volt

I is the current in amps

R is the resistance in ohm

Now,

Given that,

V = 15 volts

I = 5 amps

So,

R = V/I

  = 15/5

 = 3 Ω

⇒R = 3 Ω

Answer:

Engine bearings are lubricated by motor oils constantly supplied in sufficient amounts to the bearings surfaces. Lubricated friction is characterized by the presence of a thin film of the pressurized lubricant

Explanation:

Answer:

\❤)engineering design process(❤/

Explanation:

(♨️)BRAINLEIST PLEASE(♨️)

Answer:

ABCDEFGHIJKLMNOPQRSTUVWXYZ

Incomplete question. The options read;

A. Tech A

B. Tech B

C. Both A and B

D. Neither A nor B.

Answer:

C. Both A and B

Explanation:

Technician B is correct because the technician highlighted valid reasons why draining the compressed air systems is important.

For example, since this system helps to absorb moisture or oil from storage areas they thus need to be drained periodically in other to allow for more absorption space.

Also, the reasons mentioned by Technician A are of course correct because it is generally believed that the application of lubricants such as oil helps to reduce wear and tear.