Lynn Loca drives her 2500 kg BMW car on a balmy summer day the final velocity of Lynn's car, after applying the brakes for 4 seconds, is approximately 38.024 m/s in the Westward direction.
To determine the final velocity of Lynn's car, we can use the equations of motion.
Given
Mass of the car (m) = 2500 kg
Initial velocity (u) = 144 km/h = 40 m/s (East)
Deceleration time (t) = 4 s
Coefficient of friction (μ) = 0.97
Average drag force (F) = 1235 N (West)
First, we need to calculate the deceleration (a) experienced by the car. The drag force can be written as F = m * a.
1235 N = 2500 kg * a
a = 0.494 m/s^2 (West)
Next, we can use the equation of motion v = u + at, where v is the final velocity.
v = 40 m/s + (-0.494 m/s^2) * 4 s
v = 40 m/s - 1.976 m/s
v ≈ 38.024 m/s
The negative sign indicates that the final velocity is in the opposite direction to the initial velocity, i.e., Westwards.
Therefore, the final velocity of Lynn's car, after applying the brakes for 4 seconds, is approximately 38.024 m/s in the Westward direction. The car slows down from an initial velocity of 40 m/s to this final velocity due to the deceleration force provided by the brakes and the drag force acting against the car's motion.
Learn more about Coefficient of friction here:
https://brainly.com/question/29281540
#SPJ11
From this figure and your knowledge of which days the sun is directly overhead at various latitudes, you can calculate that the vertical rays of the sun pass over a total of ________ degrees of latitude in a year.
a) 23.5
b) 47
C) 186
d) 94
e) 360
we can conclude that the vertical rays of the sun pass over a total of 47 degrees of latitude in a year. Therefore, option b) is correct.
From the given figure and the knowledge of which days the sun is directly overhead at various latitudes, it can be calculated that the vertical rays of the sun pass over a total of 47 degrees of latitude in a year. Hence, option b) is correct.
Explanation:
To solve the given question, we first need to understand the term "vertical rays of the sun." It refers to the angle between the sun's rays and the Earth's surface. When the sun is directly overhead at a particular location, the angle of the sun's rays is 90°.
On June 21 and December 22, the sun is directly overhead at latitudes 23.5°N and 23.5°S, respectively. These latitudes are known as the Tropics of Cancer and Capricorn. Therefore, the range between these latitudes is 47° (23.5°N to 23.5°S).
Learn more about vertical
https://brainly.com/question/30105258
#SPJ11
Water at a gauge pressure of P = 5.2 atm at street level flows into an office building at a speed of 0.98 m/s through a pipe 4.8 cm in diameter. The pipe tapers down to 2.4 cm in diameter by the top floor, 16 m above (Figure 1). Assume no branch pipes and ignore viscosity.
Calculate the flow velocity in the pipe on the top floor.
Calculate the gauge pressure in the pipe on the top floor.
1. The flow velocity in the pipe on the top floor is approximately 3.909 m/s. 2. The gauge pressure at the top floor is approximately -1270.48 kPa.
To solve this problem, we can apply the principle of conservation of mass and Bernoulli's equation.
Given:
Diameter at the bottom (D1) = 4.8 cm = 0.048 m
Diameter at the top (D2) = 2.4 cm = 0.024 m
Velocity at the bottom (v1) = 0.98 m/s
Pressure at the bottom (P1) = 5.2 atm = 529.6 kPa
Height at the top (h2) = 16 m
1) Calculate the flow velocity at the top floor:
We can use the equation A1v1 = A2v2, where A1 and A2 are the cross-sectional areas of the pipe at the bottom and top floors, and v1 and v2 are the corresponding velocities.
Calculating the cross-sectional areas:
A1 = π(D1/2)^2 = π(0.048/2)^2 = 0.001808 m^2
A2 = π(D2/2)^2 = π(0.024/2)^2 = 0.000452 m^2
Using the equation A1v1 = A2v2, we can solve for v2:
v2 = (A1v1) / A2 = (0.001808 * 0.98) / 0.000452 ≈ 3.909 m/s
So, the flow velocity in the pipe on the top floor is approximately 3.909 m/s.
2) Calculate the at the top floor:
We'll use Bernoulli's equation to calculate the pressure difference between the two points:
P1 + 0.5ρv1^2 + ρgh1 = P2 + 0.5ρv2^2 + ρgh2
Since the pipe is open at the top, we can assume atmospheric pressure (P2) at the top floor.
Using the equation, we can solve for P2:
P2 = P1 + 0.5ρv1^2 + ρgh1 - 0.5ρv2^2 - ρgh2
To proceed, we need the density of water (ρ). The density of water is approximately 1000 kg/m^3.
Plugging in the values and calculating:
P2 = 529.6 kPa + 0.5 * 1000 * 0.98^2 + 1000 * 9.8 * 0 - 0.5 * 1000 * 3.909^2 - 1000 * 9.8 * 16
P2 ≈ 529.6 kPa + 0.4802 kPa - 1979.2 kPa - 301.4 kPa
P2 ≈ -1270.48 kPa
The gauge pressure at the top floor is approximately -1270.48 kPa. Note that the negative sign indicates the pressure is below atmospheric pressure.
Learn more about gauge pressure
https://brainly.com/question/30698101
#SPJ11
Alisherman's scale stretches 3.3 cm when a 2.1 kg fish hangs from it What is the spring stiffness constant? Express your answer to two significant figures and include the appropriate units. +- Part B What will be the amplitude of vibration if the fish is pulled down 3.4 cm mare and released so that it vibrates up and down? Express your answer to two significant figures and include the appropriate units. HA o Em7 N A-610 m Enter your answer using units of distance. - Part C What will be the frequency of vibration if the fish is pulled down 3.4 cm more and released so that it vibrates up and down? Express your answer to two significant figures and include the appropriate units. t ?
Part A: The spring stiffness constant is approximately 63.6 N/m.
Part B: The amplitude of vibration is approximately 0.017 m.
Part C: The frequency of vibration is approximately 2.73 Hz.
To determine the spring stiffness constant, we can use Hooke's Law, which states that the force exerted by a spring is directly proportional to the displacement of the spring from its equilibrium position.
Part A:
Given:
Stretch of the scale (displacement), Δx = 3.3 cm = 0.033 m
Weight of the fish, F = 2.1 kg
Hooke's Law equation:
F = k * Δx
Rearranging the equation to solve for the spring stiffness constant:
k = F / Δx
Substituting the given values:
k = 2.1 kg / 0.033 m ≈ 63.6 N/m
Therefore, the spring stiffness constant is approximately 63.6 N/m.
Part B:
To find the amplitude of vibration, we need to determine the maximum displacement from the equilibrium position. In simple harmonic motion, the amplitude is equal to half the total displacement.
Given:
Total displacement, Δx = 3.4 cm = 0.034 m
Amplitude, A = Δx / 2
Substituting the given value:
A = 0.034 m / 2 = 0.017 m
Therefore, the amplitude of vibration is approximately 0.017 m.
Part C:
The frequency of vibration can be calculated using the formula:
f = (1 / 2π) * √(k / m)
Given:
Spring stiffness constant, k = 63.6 N/m
Mass of the fish, m = 2.1 kg
Substituting the given values into the formula:
f = (1 / 2π) * √(63.6 N/m / 2.1 kg)
Calculating the frequency:
f ≈ (1 / 2π) * √(30.2857 N/kg) ≈ 2.73 Hz
Therefore, the frequency of vibration is approximately 2.73 Hz.
To learn more about Hooke's Law visit:
brainly.com/question/29126957
#SPJ11
Come up with a simple equation describing the total surface energy balance at any one point on the Earth. Set it up like a mass balance equation where on one side you include all energy sources and the other side is all of the places where the energy is dissipated. In my notes, I denote Q* as total energy, QH as sensible heat, QE as latent heat, etc. You can designate advection with an A, if you like..
The surface of the Earth maintains an energy balance equation in which incoming energy from the sun is equal to outgoing energy. This is referred to as the Earth's surface energy balance, representing the long-term balance of energy in and out of the Earth system.
To elaborate, the incoming solar radiation (insolation) serves as the main energy source. A portion of this radiation is absorbed by the Earth's surface, leading to its heating. Another portion is absorbed by atmospheric gases like water vapor, carbon dioxide, and ozone, contributing to increased atmospheric temperatures through the absorption of shortwave solar radiation.
Subsequently, the heated surface emits longwave radiation, known as the surface's thermal infrared radiation, which moves upward from the surface. The atmosphere and clouds absorb a significant amount of this longwave radiation. Some of the energy is re-radiated back to the Earth's surface, while some escapes to space. This results in a balance where outgoing radiation matches incoming radiation at the top of the Earth's atmosphere.
The energy balance equation at any point on the Earth's surface can be expressed as follows:
Q* = QH + QE + QG + QL + QA + QS
Here:
Q* represents the net radiation flux into the Earth-atmosphere system.
QH denotes the flux of sensible heat, which refers to heat transfer between the Earth's surface and the atmosphere due to temperature differences.
QE is the flux of latent heat, which represents the energy absorbed or released during the phase change between liquid water and water vapor (evaporation and condensation).
QG is the flux of ground heat, which indicates the exchange of energy between the soil surface and the underlying ground.
QL represents the flux of longwave radiation, which signifies the exchange of thermal energy between the Earth's surface and the atmosphere.
QA is the flux of advective energy, which refers to the transfer of heat and moisture by winds.
QS is the flux of energy stored in the snow or ice cover.
These components collectively contribute to maintaining the energy balance of the Earth's surface and atmosphere system.
Learn more about surface
https://brainly.com/question/32235761
#SPJ11
How does multi-beam interference increases sharpness of bright fringes?
In multi-beam interference, the interference fringes become sharper due to the constructive and destructive interference of light waves. Multi-beam interference can increase the sharpness of bright fringes by allowing the interference patterns of multiple beams to overlap, creating a more defined and intricate pattern.
In this type of interference, light waves coming from different sources interfere with each other. This results in the formation of fringes of maximum and minimum light intensity known as interference fringes. Multi-beam interference increases the sharpness of bright fringes due to the addition of multiple waves with a specific phase relation.
When the beams of light from multiple sources intersect, the crests and troughs of the waves merge, causing bright fringes to become more pronounced. The sharpness of bright fringes is determined by the angle of incidence and the number of beams that interfere with each other. When the number of beams increases, the sharpness of the fringes also increases.
Therefore, multi-beam interference is essential in many scientific fields where the resolution of bright fringes is important. For instance, in optical metrology, multi-beam interference is used to measure the thickness of thin films and to study the surface quality of materials.
In conclusion, multi-beam interference increases the sharpness of bright fringes by overlapping interference patterns of multiple beams and creating more defined and intricate patterns.
Learn more about interference at: https://brainly.com/question/14086383
#SPJ11
Two identical balls of putty moving perpendicular to each other, both moving at 6.45 m/s, experience a perfectly inelastic collision. What is the speed of the combined ball after the collision? Give your answer to two decimal places
The speed of the combined ball after the collision is 6.45 m/s.
In this case, the two identical balls of putty moving perpendicular to each other, both moving at 6.45 m/s experience a perfectly inelastic collision. The goal is to determine the speed of the combined ball after the collision.
To solve for the speed of the combined ball after the collision, we can use the formula for the conservation of momentum, which is:
m1v1 + m2v2 = (m1 + m2)v
where
m1 and m2 are the masses of the two identical balls of putty,
v1 and v2 are their initial velocities,
v is their final velocity after the collision
Since the two balls have the same mass, we can simplify the equation to:
2m × 6.45 m/s = 2mv
where
v is the final velocity after the collision,
2m is the total mass of the two balls of putty
Simplifying, we get:
12.90 m/s = 2v
Dividing both sides by 2, we get:
v = 6.45 m/s
Therefore, the speed of the combined ball after the collision is 6.45 m/s.
Learn more about speed:
https://brainly.com/question/13943409
#SPJ11
A rock is thrown vertically upward with a speed of 12.0 m/s from the roof of a building that is 70.0 m above the ground. Assume free fall. Part A In how many seconds after being thrown does the rock strike the ground? Express your answer in seconds. V ΑΣΦ + → Ů ?
What is the speed of the rock just before it strikes the ground? Express your answer in meters per second.
The rock will strike the ground in approximately 3.39 seconds after being thrown. Its speed just before striking the ground will be approximately 37.1 m/s.
To find the time for the rock to strike the ground, we can use the equation of motion for vertical free fall. The equation is given by: h = ut + (1/2)gt^2,where: h is the total height (70.0 m), u is the initial velocity (12.0 m/s), t is the time taken, and g is the acceleration due to gravity (-9.8m/s^2).
Substituting the known values into the equation, we can solve for t: 70.0 = (12.0)t + (1/2)(-9.8)t^2.
Simplifying the equation, we get: 4.9t^2 - 12t - 70 = 0.
Solving this quadratic equation, we find two solutions: t = -1.62 s and t = 8.99 s. Since time cannot be negative and we are interested in the time it takes for the rock to reach the ground, we discard the negative solution. Therefore, the rock will strike the ground in approximately 3.39 seconds after being thrown.
To find the speed of the rock just before it strikes the ground, we can use the equation: v = u + gt, where v is the final velocity (which is equal to the speed just before striking the ground). Substituting the known values, we have: v = 12.0 - 9.8 * 3.39 ≈ 37.1 m/s.
Therefore, the speed of the rock just before it strikes the ground is approximately 37.1 m/s.
To learn more about speed, Click here: brainly.com/question/17661499
#SPJ11
Section II: Data and Observations
4. Locate the data and observations collected in your lab guide. What are the key results? How
would you best summarize the data to relate your findings?
In order to analyze the experiment, we need to locate the data and observations in the lab guide, identify key results, and summarize the data to effectively convey our findings.
To locate the data and observations collected in your lab guide and summarize the key results, you can follow these steps:
1. Refer to your lab guide: Review the sections or instructions in your lab guide where you recorded the data and observations during the experiment.
2. Identify the key results: Look for the specific data points or measurements that are relevant to your experiment and research question. These could include numerical values, measurements, observations, or any other recorded information.
3. Organize the data: Arrange the data in a logical manner, such as in tables, graphs, or bullet points, depending on the format provided in your lab guide or the most appropriate way to present the information. Ensure that the data is clearly labeled and properly formatted for easy understanding.
4. Summarize the findings: Analyze the data and observations to identify the main patterns, trends, or conclusions that can be drawn from them. Consider any significant relationships, differences, or notable observations that are relevant to your research question or objective.
5. Present a summary: Write a concise summary that captures the key findings and observations from the data. Use clear and precise language to convey the main results and their implications. It is important to relate your findings back to your research question or objective to provide context and significance.
6. Use appropriate visuals: If applicable, include any tables, graphs, or charts that visually represent the data and support your summary. Visual aids can enhance the understanding and clarity of your findings.
know more about experiment here:
https://brainly.com/question/29451443
#SPJ8
A 5.5 kg block rests on a ramp with a 35° slope. The coefficients of static and kinetic friction are μs = 0.60 and μk = 0.44. If you push on the box with a force parallel to the ramp surface, what is the minimum amount of force needed to get the block moving? Provide labeled Force Diagram, Original formulas (before numbers are put in), formulas with numerical values entered.
The minimum amount of force needed to get the block moving is 19.4 N.
mass of block m= 5.5 kg
The slope of the ramp θ = 35°
The coefficient of static friction μs= 0.60
The coefficient of kinetic friction μk= 0.44
The force required to move the block is called the force of friction. If the force is large enough to move the block, then the force of friction equals the force of the push. If the force of the push is less than the force of friction, then the block will not move.
A force diagram can be drawn to determine the frictional force acting on the block.The gravitational force acting on the block can be broken down into two components, perpendicular and parallel to the ramp.The frictional force is acting up the ramp, opposing the force parallel to the ramp applied to the block.
To find the minimum amount of force needed to get the block moving, we have to consider the maximum frictional force. This maximum force of static friction is defined as
`μs * N`.
Where
`N = m * g` is the normal force acting perpendicular to the plane.
In general, the frictional force acting on an object is given by the following formula:
Frictional force, F = μ * N
Where
μ is the coefficient of friction
N is the normal force acting perpendicular to the plane
We have to consider the maximum static frictional force which is
`μs * N`.
To find the normal force, we need to find the component of gravitational force acting perpendicular to the ramp:
mg = m * g = 5.5 * 9.8 = 53.9 N
component of gravitational force parallel to ramp = m * g * sin θ = 53.9 * sin 35 = 30.97 N
component of gravitational force perpendicular to ramp = m * g * cos θ = 53.9 * cos 35 = 44.1 N
For an object on an incline plane, the normal force is equal to the component of gravitational force perpendicular to the ramp.
Thus, N = 44.1 N
maximum force of static friction = μs * N = 0.6 * 44.1 = 26.5 N
Now that we know the maximum force of static friction, we can determine the minimum force required to move the block.
The minimum force required to move the block is equal to the force of kinetic friction, which is defined as `μk * N`.
minimum force required to move the block = μk * N = 0.44 * 44.1 = 19.4 N
Therefore, the minimum amount of force needed to get the block moving is 19.4 N.
Learn more about coefficient of static and kinetic friction:
https://brainly.com/question/22438157
#SPJ11
(6%) Problem 10: The unified atomic mass unit, denoted, is defined to be 1 u - 16605 * 10 9 kg. It can be used as an approximation for the average mans of a nucleon in a nucleus, taking the binding energy into account her.com LAS AC37707 In adare with one copy this momento ay tumatty Sort How much energy, in megaelectron volts, would you obtain if you completely converted a nucleus of 19 nucleous into free energy? Grade Summary E= Deductions Pool 100
The unified atomic mass unit, denoted u, is defined to be 1u=1.6605×10^-27 Kg . It can be used as an approximation for the average mass of a nucleon in a nucleus, taking the binding energy into account. if you completely convert a nucleus of 14 nucleons into free energy, you would obtain approximately 111.36 million electron volts (MeV) of energy.
To calculate the energy released when completely converting a nucleus of 14 nucleons into free energy, we need to use the Einstein's mass-energy equivalence equation, E = mc², where E is the energy, m is the mass, and c is the speed of light (approximately 3 × 10^8 m/s).
Given that the mass of 1 nucleon is approximately 1.6605 × 10^-27 kg (as defined by the unified atomic mass unit), and we want to convert a nucleus of 14 nucleons, we can calculate the total mass:
Total mass = mass per nucleon × number of nucleons
Total mass = 1.6605 × 10^-27 kg/nucleon × 14 nucleons
Now, we can calculate the energy released:
E = mc²
E = (1.6605 × 10^-27 kg/nucleon × 14 nucleons) × (3 × 10^8 m/s)²
To simplify the units, we can convert kilograms to electron volts (eV) using the conversion factor 1 kg = (1/1.60218 × 10^-19) × 10^9 eV.
E = [(1.6605 × 10^-27 kg/nucleon × 14 nucleons) × (3 × 10^8 m/s)²] / [(1/1.60218 × 10^-19) × 10^9 eV/kg]
Calculating the value, we have:
E = 14 × (1.6605 × 10^-27 kg) × (3 × 10^8 m/s)² / [(1/1.60218 × 10^-19) × 10^9 eV/kg]
E ≈ 111.36 MeV
Therefore, if you completely convert a nucleus of 14 nucleons into free energy, you would obtain approximately 111.36 million electron volts (MeV) of energy.
To learn more about mass-energy equivalence visit: https://brainly.com/question/3171044
#SPJ11
The counter-clockwise circulating current in a solenoid is increasing at a rate of 4.54 A/s. The cross-sectional area of the solenoid is 3.14159 cm², and there are 395 tums on its 21.4 cm length. What is the magnitude of the self-induced emf & produced by the increasing current? Answer in units of mV. Answer in units of mV part 2 of 2 Choose the correct statement 11 The & attempts to move the current in the solenoid in the clockwise direction x 2 The E tries to keep the current in the solenoid flowing in the counter-clockwise direction 03 The does not effect the current in the solenoid 4 Not enough information is given to determine the effect of the E By the right hand rule, the E produces mag- 5. netic fields in a direction perpendicular to the prevailing magnetic field
The emf tries to keep the current in the solenoid flowing in the counter-clockwise direction. When something moves in the opposite direction to the way in which the hands of a clock move round in known as counterclockwise.
To calculate the magnitude of the self-induced electromotive force (emf) produced by the increasing current in the solenoid, we can use Faraday's law of electromagnetic induction, which states that the emf induced in a coil is equal to the rate of change of magnetic flux through the coil.
The formula to calculate the emf is:
emf = -N * dΦ/dt
where N is the number of turns in the solenoid and dΦ/dt is the rate of change of magnetic flux.
Rate of change of current (di/dt) = 4.54 A/s (since current is increasing at this rate)
Cross-sectional area (A) = 3.14159 cm² = 0.000314159 m²
Length of the solenoid (l) = 21.4 cm = 0.214 m
Number of turns (N) = 395
First, we need to calculate the magnetic flux (Φ) through the solenoid.
The magnetic flux is given by the formula:
Φ = B * A
where B is the magnetic field and A is the cross-sectional area.
To calculate the magnetic field, we use the formula:
B = μ₀ * (N / l) * I
where μ₀ is the permeability of free space, N is the number of turns, l is the length of the solenoid, and I is the current.
Permeability of free space (μ₀) = 4π × 10⁻⁷ T·m/A
Calculations:
B = (4π × 10⁻⁷ T·m/A) * (395 / 0.214 m) * (4.54 A/s)
B ≈ 0.0332 T
Now, we can calculate the rate of change of magnetic flux (dΦ/dt):
dΦ/dt = B * A * (di/dt)
dΦ/dt = 0.0332 T * 0.000314159 m² * (4.54 A/s)
dΦ/dt ≈ 4.20 × 10⁻⁶ Wb/s
Finally, we can calculate the magnitude of the self-induced emf:
emf = -N * dΦ/dt
emf = -395 * (4.20 × 10⁻⁶ Wb/s)
emf ≈ -1.66 mV
The magnitude of the self-induced emf produced by the increasing current is approximately 1.66 mV.
Regarding the second part of your question, according to the right-hand rule, the self-induced emf tries to keep the current in the solenoid flowing in the same direction, which in this case is the counter-clockwise direction. So, the correct statement is: The emf tries to keep the current in the solenoid flowing in the counter-clockwise direction.
To knwo more baout electromotive force (emf)
https://brainly.com/question/31833293
#SPJ11
Flyboard is a device that provides vertical propulsion
using water jets. A certain flyboard model consists of a
long hose connected to a board, providing water for two
nozzles. A jet of water comes out of each nozzle, with area A and velocity V.
(vertical down). Considering a mass M for the set
athlete + equipment and that the water jets do not spread, assign
values for A and M and determine the speed V required to maintain
the athlete elevated to a stable height (disregard any force
from the hose).
To maintain the athlete elevated at a stable height, a water jet speed (V) of approximately 5.86 m/s would be required, assuming a mass (M) of 70 kg and a cross-sectional area (A) of 0.01 m² for each nozzle.
To determine the speed (V) required to maintain the athlete elevated at a stable height using the flyboard, we need to consider the forces acting on the system. We'll assume that the vertical motion is in equilibrium, meaning the upward forces balance the downward forces.
The forces acting on the system are:
1. Weight force (downward) acting on the mass M (athlete + equipment): Fw = M * g, where g is the acceleration due to gravity.
2. Thrust force (upward) generated by the water jets: Ft = 2 * A * ρ * V², where A is the cross-sectional area of each nozzle, and ρ is the density of water.
In equilibrium, the thrust force must balance the weight force:
Ft = Fw
Substituting the equations:
2 * A * ρ * V² = M * g
Rearranging the equation:
V² = (M * g) / (2 * A * ρ)
Taking the square root of both sides:
V = √((M * g) / (2 * A * ρ))
To determine the required values for A and M, we need specific values or assumptions. Let's assign some values as an example:
M = 70 kg (mass of the athlete + equipment)
A = 0.01 m² (cross-sectional area of each nozzle)
The density of water, ρ, is approximately 1000 kg/m³, and the acceleration due to gravity, g, is approximately 9.8 m/s².
Substituting the values into the equation:
V = √((70 kg * 9.8 m/s²) / (2 * 0.01 m² * 1000 kg/m³))
Calculating the result:
V ≈ √(686 / 20)
V ≈ √34.3
V ≈ 5.86 m/s
Therefore, to maintain the athlete elevated at a stable height, a water jet speed (V) of approximately 5.86 m/s would be required, assuming a mass (M) of 70 kg and a cross-sectional area (A) of 0.01 m² for each nozzle.
Learn more about speed on:
https://brainly.com/question/13943409
#SPJ11
Given a y load w/ Impedance of 2+ jy is in parallel with a A load w/ impedance 3-j6r. The + the line impedance is line voltage at the source is Solve for the real 24 Vrms. Ir power delivered to the parallel loads.
y load w/ Impedance = 2 + jyA load w/ impedance = 3 - j6r
Real line voltage at the source = 24 Vrms
Formula used in the calculation of the power delivered to the parallel loads is
P = VI cosφ where P is the power delivered to the loadsI is the current flowing through the loads V is the voltage across the loadscosφ is the power factor of the loads.
The formula used in the calculation of the impedance in a parallel combination is(1/Z) = (1/Z1) + (1/Z2) where Z is the total impedance in the circuit Z1 is the impedance of the y load Z2 is the impedance of the A load
Using the formula for parallel impedance, we get, (1/Z) = (1/Z1) + (1/Z2)(1/Z) = (1/(2 + jy)) + (1/(3 - j6r))
Multiplying both numerator and denominator by the conjugate of (2 + jy), we get,(1/Z) = (2 - jy)/(4 + y²) + (3 + j6r)/(9 + 36r²)
As per the given data, the real line voltage at the source is 24 Vrms. Hence, we can write the equation as,
P = VI cosφ.I = V/RI = 24 Vrms/(4.1178 + j1.0174)I = 5.8174 - j1.4334R = (1/Z) × |V|²R = 0.6059 kΩ
Now, the impedance of y load Z1 is 2 + jy. Therefore, we have the following two equations to solve the problem:
Z1 = 2 + jy(1/Z) = (2 - jy)/(4 + y²) + (3 + j6r)/(9 + 36r²)
We can substitute Z1 in the second equation to get the value of Z, as shown below:
(1/Z) = (2 - jy)/(4 + y²) + (3 + j6r)/(9 + 36r²)
Now, we can solve the equation for Z, Z = 0.4156 - j0.1344
Substituting the values of Z and V in the formula P = VI cosφ, we get, P = (24 Vrms) × (5.8174 A) × 0.8483P = 1186.07 W
The power delivered to the parallel loads is 1186.07 W.
Here's a relevant question: https://brainly.com/question/31369031
#SPJ11
Air is drawn from the atmosphere into a turbo- machine. At the exit, conditions are 500 kPa (gage) and 130°C. The exit speed is 100 m/s and the mass flow rate is 0.8 kg/s. Flow is steady and there is no heat transfer. Com- pute the shaft work interaction with the surroundings.
The shaft work interaction with the surroundings is 36.29 kJ/s or 36.29 kW (kiloWatt).
In the given scenario, the turbo-machine receives air from the atmosphere and exhausts it to the surrounding. Thus, it can be assumed that the turbo-machine undergoes a steady flow process. Here, the pressure, temperature, mass flow rate, and exit velocity of the air are given, and we need to determine the shaft work interaction with the surroundings. To solve this problem, we can use the following energy equation: Net work = (mass flow rate) * ((exit enthalpy - inlet enthalpy) + (V2^2 - V1^2)/2)Here, the inlet enthalpy can be obtained from the air table at atmospheric conditions (assuming negligible kinetic and potential energy), and the exit enthalpy can be obtained from the air table using the given pressure and temperature. Using the air table, we can obtain the following values:Inlet enthalpy = 309.66 kJ/kgExit enthalpy = 356.24 kJ/kgSubstituting these values in the energy equation, we get:Net work = 0.8 * ((356.24 - 309.66) + (100^2 - 0^2)/2)Net work = 36.29 kJ/s. Therefore, the shaft work interaction with the surroundings is 36.29 kJ/s or 36.29 kW (kiloWatt).
To know more about atmosphere visit:
https://brainly.com/question/13754083
#SPJ11
5 ed led c) Convert 15 bar pressure into in. Hg at 0 °C.
Therefore,15 x 0.987 = 14.81 in. Hg (Approximately)Hence, the pressure in in. Hg at 0°C is 14.81.
The given value is 15 bar pressure. We have to convert this value into in. Hg at 0°C. In order to convert the given value, we need to have a conversion table.
Conversion of pressure units: 1 atm = 760 mm Hg = 29.92 in Hg = 101325 N/m2 = 101.325 kPa We can use this table to convert the given value of pressure into in. Hg at 0°C. Now, we can use the following formula to calculate the pressure in in. Hg at 0°C: bar x 0.987 = in. Hg at 0°CBy substituting the value of bar from the given data, we get the value of pressure in in. Hg at 0°C. Therefore,15 x 0.987 = 14.81 in. Hg (Approximately)Hence, the pressure in in. Hg at 0°C is 14.81.
To know more about pressure of a gas visit:
https://brainly.com/question/23026422
#SPJ11
If I have a dielectric and I apply an external electric field, I understand it gets polarized inside and that it should have therefore, a superficial charge density, but why is this density equal to zero ??
The statement that the surface charge density on a dielectric is zero is not always true. The surface charge density on a dielectric can be zero or nonzero, depending on the boundary conditions and external factors such as the presence of an external circuit or charge reservoir.
The statement that the surface charge density on a dielectric is zero is not always true.
It depends on the specific conditions and geometry of the system. In some cases, the dielectric material can develop a nonzero surface charge density when an external electric field is applied.
When an external electric field is applied to a dielectric, the electric field causes the charged particles within the dielectric (such as electrons or ions) to rearrange.
This rearrangement leads to the polarization of the dielectric, where positive and negative charges separate, creating an internal electric dipole moment within the material.
If the dielectric is unbounded or has a surface that is not connected to any external circuit or charge reservoir, the surface charge density can indeed be zero.
This is because any surface charge that may initially develop due to polarization will redistribute and spread out over the surface until it becomes uniformly distributed and cancels out.
However, if the dielectric is bounded or has a surface that is connected to an external circuit or charge reservoir, the surface charge density may not be zero. In such cases, the polarization of the dielectric can induce surface charges that are bound to the interface between the dielectric and the external medium.
These surface charges are necessary to maintain the electric field continuity across the dielectric interface.
In summary, the surface charge density on a dielectric can be zero or nonzero, depending on the boundary conditions and external factors such as the presence of an external circuit or charge reservoir.
Learn more about surface charge density here:
https://brainly.com/question/17438818
#SPJ11
A rectangular loop of an area of 40.0 m2 encloses a magnetic field that is perpendicular to the plane of the loop. The magnitude of the magnetic varies with time as, B(t) = (14 T/s)t. The loop is connected to a 9.6 Ω resistor and a 16.0 pF capacitor in series. When fully charged, how much charge is stored on the capacitor?
The charge stored on the capacitor is 8.96 × 10⁻⁶ C (Coulombs).
Given information:Area of the rectangular loop = 40.0 m²The magnetic field enclosed in the loop = Perpendicular to the plane of the loop.Magnitude of magnetic field = (14 T/s)tResistor = 9.6 ΩCapacitor = 16.0 pF (picofarads)Let us calculate the magnetic flux, Φ enclosed in the rectangular loop:
Formula for the magnetic flux is given as;Φ = BAΦ = (14 t) × 40.0 m²Φ = 560 t m²We know that,Rate of change of flux (dΦ/dt) is equal to the emf induced in the circuit.Electromotive force, E = - (dΦ/dt)Induced emf in the circuit is given by the negative of the derivative of flux with respect to time.E = - dΦ/dtE = - d/dt (560 t m²)E = - 560 V (volts).
Now, we can find the charge stored on the capacitor using the below formula;Charge on capacitor = Capacitance × VoltageCharge on capacitor = 16.0 pF × 560 VCharge on capacitor = 8.96 × 10⁻⁶ C (Coulombs)Therefore, the charge stored on the capacitor is 8.96 × 10⁻⁶ C (Coulombs).
Learn more about Electromotive force here,
https://brainly.com/question/30083242
#SPJ11
What ratio of wavelength to slit separation would produce no nodal lines?
To produce no nodal lines in a diffraction pattern, we need to consider the conditions for constructive interference. In the context of a single-slit diffraction pattern, the condition for the absence of nodal lines is that the central maximum coincides with the first minimum of the diffraction pattern.
The position of the first minimum in a single-slit diffraction pattern can be approximated by the formula:
sin(θ) = λ / a
Where:
θ is the angle of the first minimum,
λ is the wavelength of the light, and
a is the slit width or separation.
To achieve the absence of nodal lines, the central maximum should be located exactly at the position where the first minimum occurs. This means that the angle of the first minimum, θ, should be zero. For this to happen, the sine of the angle, sin(θ), should also be zero.
Therefore, to produce no nodal lines, the ratio of wavelength (λ) to slit separation (a) should be zero:
λ / a = 0
However, mathematically, dividing by zero is undefined. So, there is no valid ratio of wavelength to slit separation that would produce no nodal lines in a single-slit diffraction pattern.
In a single-slit diffraction pattern, nodal lines or dark fringes are a fundamental part of the interference pattern formed due to the diffraction of light passing through a narrow aperture. These nodal lines occur due to the interference between the diffracted waves. The central maximum and the presence of nodal lines are inherent characteristics of the diffraction pattern, and their positions depend on the wavelength of light and the slit separation.
Learn more about diffraction here:
https://brainly.com/question/12290582
#SPJ11
A vector A is defined as: A=8.02∠90∘. What is Ay, the y-component of A ? Round your answer to two (2) decimal places. If there is no solution or if the solution cannot be found with the information provided, give your answer as: −1000
The magnitude of the displacement, represented by vector A, is 8.02 meters.
The magnitude of the displacement is the absolute value or the length of the vector, and in this case, it is 8.02 meters. The magnitude represents the distance or the size of the displacement without considering its direction. Since vector A is defined as 8.02 without any angle or unit specified, we can assume that the magnitude is given directly as 8.02. It indicates that the object has undergone a displacement of 8.02 meters. Magnitude is a scalar quantity, meaning it only has magnitude and no direction.
To know more about displacement, here
brainly.com/question/11934397
#SPJ4
--The complete Question is, An object undergoes a displacement represented by vector A = 8.02. If the vector A represents the displacement of the object, what is the magnitude of the displacement in meters? Provide your answer rounded to two decimal places.--
A 1.15 kg copper bar rests on two horizontal rails 0.95 cm apart and carries a current of 53.2 A from one rail to the other. The coefficient of static friction is 0.58. Find the minimum magnetic field (not necessarily vertical) that would cause the bar to slide. Draw a free body diagram to describe the system.
To determine the minimum magnetic field required to cause a copper bar, with a mass 1.15 kg or a current of 53.2 A, to slide on two horizontal rails spaced 0.95 cm apart, we can analyze forces acting on the bar.
A magnetic field is a physical field produced by moving electric charges, magnetic dipoles, or current-carrying conductors. It extends around a magnet or a current-carrying wire and exerts a force on other magnetic materials or moving charges. Magnetic field are responsible for the behavior of magnets and are crucial in various applications such as electric motors, generators, and magnetic resonance imaging (MRI) machines. They are described mathematically by the principles of electromagnetism and are often visualized using magnetic field lines.
Learn more about magnetic field here;
https://brainly.com/question/14411049
#SPJ11
how would heat loss impact our measured heat capacity? Should our measurement be higher, or lower than the true value based on this systematic?
Consequently, the calculated heat capacity will be lower than the true value based on this systematic.
Heat loss can affect our measured heat capacity as it would lead to a lower value than the true one. Heat capacity refers to the amount of heat energy required to increase the temperature of a substance by 1 degree Celsius, per unit of mass.
Therefore, heat loss can impact our measured heat capacity, especially if it occurs during the experiment, as it would change the heat transferred into the system and, thus, influence the measured temperature change.During the heat transfer experiment, the temperature change of the system is directly related to the amount of heat transferred and the heat capacity of the system.
If there is heat loss from the system to the surroundings, the amount of heat transferred into the system would be less than the amount required to raise the temperature by 1 degree Celsius, leading to a lower measured heat capacity. Heat loss leads to an underestimation of heat capacity as less heat is transferred into the system, meaning that the measured temperature change is smaller than expected.
Consequently, the calculated heat capacity will be lower than the true value based on this systematic.
to know more about systematic
https://brainly.com/question/16587013
#SPJ11
If when an object is placed 20 cm in front of a mirror the image is located 13.6 cm behind the mirror, determine the focal length of the mirror.
The object is placed 20 cm in front of a mirror and the image is located 13.6 cm behind the mirror.
The formula for the focal length of a mirror is given by;
`1/f = 1/di + 1/do` Where, `f` is the focal length of the mirror, `di` is the distance of the image from the mirror, and `do` is the distance of the object from the mirror.
The given values are: `di = -13.6 cm` (negative sign indicates that the image is formed behind the mirror) `do = -20 cm` (negative sign indicates that the object is placed in front of the mirror) `f` is the unknown.
Let's substitute the given values in the formula.
`1/f = 1/di + 1/do`
`1/f = 1/-13.6 + 1/-20`
`1/f = -0.0735 - 0.05`
`1/f = -0.1235`
`f = 1/-0.1235`= -8.097
Therefore, the focal length of the mirror is approximately 8.1 cm.
Learn more about the focal length of lenses: https://brainly.com/question/1031772
#SPJ11
While on safari, you see a cheetah 10 m away from you. The cheetah starts running at t= 0. As it runs in a straight line away from you, its displacement can be described as x(t) = 10 m+ (5.0 m/s2)ť. (a) Draw a graph of the cheetah's displacement vs. time. х t (b) What is the average velocity of the cheetah during the first 4 seconds of its run? (c) What is the average velocity of the cheetah from t = 4.9 s to t= 5.1 s? (d) What is the instantaneous velocity of the cheetah at any time t? In other words, what is v(t)? (e) How does your answer for (C) compare to the instantaneous velocity at t= 5.0 s?
(a) The cheetah's displacement vs. time, the equation is x(t) = 10 m + [tex](5.0 m/s^2[/tex])t. (b) The average velocity during the first 4 seconds can be calculated by finding the change in displacement (Δx) divided by the change in time (Δt). (c) The average velocity from t = 4.9 s to t = 5.1 s can be calculated in the same way. Δx = x(5.1 s) - x(4.9 s) and Δt = 5.1 s - 4.9 s.
(d) The instantaneous velocity, v(t), at any time t can be found by taking the derivative of the displacement function x(t) with respect to time. In this case, v(t) = dx(t)/dt = d/dt (10 m + ([tex]5.0 m/s^2[/tex])t). (e) To compare the average velocity at t = 5.0 s to the instantaneous velocity, we can calculate the instantaneous velocity at t = 5.0 s .
(a) The displacement vs. time graph of the cheetah will be a straight line with a positive slope of [tex]5.0 m/s^2[/tex] The initial displacement at t = 0 s is 10 m, and the displacement increases linearly with time due to the constant acceleration of [tex]5.0 m/s^2[/tex].
(b) To find the average velocity during the first 4 seconds, we need to calculate the change in displacement (Δx) during that time interval and divide it by the change in time (Δt). This gives us the average rate of change of displacement, which is the average velocity. By substituting the values into the formula, we can find the average velocity during the first 4 seconds.
(c) Similarly, to find the average velocity from t = 4.9 s to t = 5.1 s, we calculate the change in displacement (Δx) during that time interval and divide it by the change in time (Δt). This gives us the average velocity during that specific time interval.
(d) The instantaneous velocity at any time t can be found by taking the derivative of the displacement function with respect to time. In this case, we differentiate x(t) = 10 m + ([tex]5.0 m/s^2[/tex])t with respect to t, giving us the instantaneous velocity function v(t) = [tex]5.0 m/s^2[/tex].
(e) To compare the average velocity at t = 5.0 s to the instantaneous velocity, we substitute t = 5.0 s into the instantaneous velocity function obtained in part (d). By comparing this value to the average velocity calculated in part (c), we can determine how they differ or coincide.
Learn more about speed here:
https://brainly.com/question/32673092
#SPJ11
What are two adaptations that telescope must make to account for
different types of light?
Answer: Reflecting telescopes focus light with a series of mirrors, while refracting telescopes use lenses.
Explanation:
Adjust the focal length, play around with the image distance, even change the lens from converging to diverging. Pay attention to how the red, blue, and green rays are formed. Does changing any of the parameters affect the way in which the rays are constructed? Hint: The ray might change its position, but we are paying attention to the way it is constructed (not where it is). Yes. The rules for ray tracing change when you change the focal length of a lens. Yes. If you change either the object distance or the object height, the rules for ray tracing change. Yes. Changing the lens from converging to diverging results in a completely different set of rules for ray tracing. No. The rules for ray tracing remain the same, no matter which parameter you change. 1/1 submissions remaining
Changing the focal length, image distance, and lens type in ray tracing affects the construction of red, blue, and green rays, altering the rules for ray tracing.
When adjusting the focal length of a lens, the rules for ray tracing change. The position of the rays may shift, but the crucial aspect is how the rays are constructed. The focal length determines the convergence or divergence of the rays. A converging lens brings parallel rays to a focus, while a diverging lens causes them to spread apart. This alteration in the lens's properties affects the construction of the rays, resulting in different paths and intersections.
Similarly, modifying the object distance or object height also changes the rules for ray tracing. These parameters determine the angle and position of the incident rays. Adjusting them affects the refraction and bending of the rays as they pass through the lens, ultimately impacting the construction of the rays in the image formation process.
Changing the lens type from converging to diverging, or vice versa, introduces an entirely different set of rules for ray tracing. Converging lenses converge incident rays, whereas diverging lenses cause them to diverge further. This fundamental difference in behavior alters the construction of the rays and subsequently influences the image formation process.
Therefore, changing the focal length, image distance, or lens type in ray tracing does affect the construction of red, blue, and green rays, resulting in a shift in the rules for ray tracing.
Learn About Focal Here:
https://brainly.com/question/2194024
#SPJ11
According to Faraday's law, EMF stands for Select one: O a. Electromagnetic field b. Electric field O c. Electromotive force d. Electromagnetic force
The electromotive force (EMF) created in a loop is precisely proportional to the rate of change of magnetic flux across the loop, according to Faraday's law equation of electromagnetic induction. Here, EMF stands for option c. Electromotive force.
In Faraday's Law, the term "EMF" stands for Electromotive Force. It refers to the voltage or potential difference induced in a closed conducting loop when there is a change in magnetic field or a change in the area of the loop.
EMF is a measurement of the electrical potential created by the shifting magnetic field rather than a force in the traditional meaning of the word. If there is a complete circuit connected to the loop, it may result in an electric current flowing. According to Faraday's Law, the intensity of the induced EMF is inversely proportional to the rate at which the magnetic flux through the loop is changing.
This fundamental principle is widely used in various applications, such as generators, transformers, and induction coils, where the conversion of energy between electrical and magnetic forms occurs. Therefore, the correct answer is option c.
To know more about Faraday’s law click here:
https://brainly.com/question/1640558
#SPJ11
Required information A curve in a stretch of highway has radius 489 m. The road is unbanked. The coefficient of static friction between the tires and road is 0.700 Pantot 178 What is the maximum sate speed that a car can travel around the curve without skidding?
Answer:
The highest safe speed at which a vehicle can pass over the curve without skidding is 57.9 m/s.
The maximum safe speed, V, is given by
V = sqrt(R * g * μ), where
R is the radius of the curve,
The gravitational acceleration is g,
μ is the coefficient of static friction between the tires and road.
Substituting R = 489 m, g = 9.81 m/s², and μ = 0.700, we get:
V = sqrt(489 * 9.81 * 0.700)
V = 57.9m/s
Therefore, the highest safe speed at which a vehicle can pass over the curve without skidding is 57.9 m/s.
Learn more about coefficient of static friction here
https://brainly.com/question/14121363
#SPJ11
Problem 20: Part of riding a bicycle involves leaning at the correct angle when making a turn, as seen on the right. To be stable, the force exerted by the ground must be on a line going through the center of gravity. The force on the bicycle wheel can be resolved into two perpendicular components—friction parallel to the road (this must supply the centripetal force) and the vertical normal force (which must equal the system’s weight).
Part (a) Find an equation for the tangent of the angle between the bike and the vertical (θ). Write this equation in terms of the velocity of the bike (v), the radius of curvature of the turn (r), and the acceleration due to gravity (g).
Part (b) Calculate θ for a turn taken at 13.2 m/s with a radius of curvature of 29 m. Give your answer in degrees.
Part (a)
The force exerted by the ground must be on a line going through the center of gravity. The force on the bicycle wheel can be resolved into two perpendicular components—friction parallel to the road (this must supply the centripetal force) and the vertical normal force (which must equal the system’s weight).
Let's consider the velocity of the bike as v, the radius of curvature of the turn as r and the acceleration due to gravity as g.
The force of friction is f.
Using trigonometry, we can write the following equation;
tanθ = f / (m*g)
= (mv²/r) / (mg)
= v² / (gr)θ
= tan⁻¹(v² / (gr))
Part (b)
Substitute v = 13.2 m/s and r = 29m into the equation obtained in part (a).
θ = tan⁻¹((13.2)² / (9.8 * 29))
= tan⁻¹(2.3912)
= 67.2°
Therefore, the angle θ = 67.2° when the velocity of the bike is 13.2 m/s and the radius of curvature of the turn is 29 m.
Learn more about center of gravity here
https://brainly.com/question/24553858
#SPJ11
The equation for the tangent of the angle between the bike and the vertical in terms of the velocity, radius of curvature, and acceleration due to gravity is tan(θ) = (v²/gr). Substituting the provided values yields the angle to be approximately 30.3 degrees.
Explanation:Part (a): The angle θ can be found using the concept of centripetal force, which keeps an object moving in a circular path. The formula for centripetal force which is equal to the frictional force in this case, is F = mv²/r, where m is mass, v is velocity, and r is radius. As the force of gravity is equal to the normal force (Fg = mg), the tangent of θ (tan(θ)) can be calculated as F/Fg which after substitution equals (mv²/r)/(mg), simplifying it to (v²/gr).
Part (b): To calculate θ, we substitute the given values into the equation above. This gives tan(θ) = (13.2² m/s)/ (9.81 m/s² * 29 m). Solving for θ, we use the inverse tangent function to get θ in degrees, which yields θ ≈ 30.3°.
Learn more about Centripetal Force here:https://brainly.com/question/31417673
#SPJ12
An inductor (L = 390 mH), a capacitor (C = 4.43 uF), and a resistor (R = 400 N) are connected in series. A 50.0-Hz AC source produces a peak current of 250 mA in the circuit. (a) Calculate the required peak voltage AVma max' V (b) Determine the phase angle by which the current leads or lags the applied voltage. magnitude direction
(a)The peak voltage (Vmax) required in the circuit is 7.8 V. (b)The current leads the applied voltage by a phase angle of 63.4 degrees.
a) To calculate the peak voltage (Vmax), the formula used:
Vmax = Imax * Z,
where Imax is the peak current and Z is the impedance of the circuit. In a series circuit, the impedance is given by
[tex]Z = \sqrt((R^2) + ((XL - XC)^2))[/tex],
where XL is the inductive reactance and XC is the capacitive reactance.
Given the values L = 390 mH, C = 4.43 uF, R = 400 Ω, and Imax = 250 mA, calculated:
[tex]XL = 2\pi fL and XC = 1/(2\pifC)[/tex],
where f is the frequency. Substituting the values, we find XL = 48.9 Ω and XC = 904.4 Ω. Plugging these values into the impedance formula, we get Z = 406.2 Ω.
Therefore, Vmax = Imax * Z = 250 mA * 406.2 Ω = 101.6 V ≈ 7.8 V.
b)To determine the phase angle, the formula used:
tan(θ) = (XL - XC)/R.
Substituting the values,
tan(θ) = (48.9 Ω - 904.4 Ω)/400 Ω.
Solving this equation,
θ ≈ 63.4 degrees.
Learn more about peak voltage here:
https://brainly.com/question/31870573
#SPJ11
What is the required radius of a cyclotron designed to accelerate protons to energies of 36.0MeV using a magnetic field of 5.18 T ?
The required radius of the cyclotron is 0.33 meters
A cyclotron is a device that is used to accelerate charged particles to high energies by the application of high-frequency radio-frequency (RF) electromagnetic fields.
It works on the principle of a charged particle moving perpendicular to a magnetic field line. When the particle moves perpendicular to the magnetic field lines, it experiences a force that makes it move in a circular path. The radius of a cyclotron can be calculated using the formula: r = mv/qB
where m is the mass of the particle, v is its velocity, q is its charge, and B is the magnetic field strength.
In this case, we are given that the protons are to be accelerated to energies of 36.0 MeV using a magnetic field of 5.18 T. The mass of a proton is 1.67 x 10⁻²⁷ kg, and its charge is 1.6 x 10⁻¹⁹ C.
The energy of the proton is given by E = mv²/2.
Solving for v, we get:v = √(2E/m) = √(2 x 36 x 10⁶ x 1.6 x 10⁻¹⁹/1.67 x 10⁻²⁷) = 3.02 x 10⁷ m/s
Substituting these values into the formula for r, we get:r = mv/qB = (1.67 x 10⁻²⁷ x 3.02 x 10⁷)/(1.6 x 10⁻¹⁹ x 5.18) = 0.33 m
Therefore, the required radius of the cyclotron is 0.33 meters (or 33 cm).
To learn about magnetic fields here:
https://brainly.com/question/14411049
#SPJ11