The power that can be produced by an ideal hydraulic turbine if water is run through the turbine at a rate of 1500 L/s is 1.924 MW (megawatts).
The potential energy of the water in the dam is given by mgh, where m is the mass of the water, g is the acceleration due to gravity, and h is the height of the dam. The mass of the water can be determined using the density of water which is 1000 kg/m³ and the volume flow rate which is 1500 L/s, which gives m = 1500 kg/s.
The potential energy of the water is therefore given by: PE = mgh= 1500 × 9.81 × 65= 9,569,250 J/s or 9.569 MW (megawatts)
Since the hydraulic turbine is an ideal device, all the potential energy of the water can be converted to kinetic energy, and then to mechanical energy that can be used to turn a generator. The mechanical energy can be calculated using the formula KE = (1/2)mv², where v is the velocity of the water at the turbine. The velocity of the water can be determined using the formula Q = Av, where Q is the volume flow rate, A is the cross-sectional area of the turbine, and v is the velocity of the water.
Assuming the turbine has a circular cross-section, the area can be calculated using the formula A = πr², where r is the radius of the turbine.
Since the volume flow rate is given as 1500 L/s, which is equivalent to 1.5 m³/s, we have:1.5 = πr²v
The velocity of the water is therefore: v = 1.5/πr²
Substituting the value of v in the kinetic energy formula and simplifying, we obtain: KE = (1/2)mv²= (1/2)m(1.5/πr²)²= (1/2) × 1500 × (1.5/πr²)²= 2.774 W
Therefore, the power that can be produced by the hydraulic turbine is: PE = KE = 2.774 W= 2.774 × 10⁶ MW= 1.924 MW (approximately)
know more about hydraulic turbine
https://brainly.com/question/13065056
#SPJ11
Mod1HW
Problem 20: A student begins at rest and then walks north at a speed of v1 = 0.75 m/s. The student then turns south and walks at a speed of v2 = 0.76 m/s. Take north to be the positive direction. Refer to the figure.
Part (a) What is the student's overall average velocity vavg, in meters per second, for the trip assuming the student spent equal times at speeds v1 and v2?
Part (b) If the student travels in the stated directions for 30.0 seconds at speed v1 and for 20.0 seconds at speed v2, what is the net displacement, in meters, during the trip?
Part (c) If it takes the student 5.0 s to reach the speed v1 from rest, what is the magnitude of the student’s average acceleration, in meters per second squared, during that time?
Part a)The total distance covered is, D = 2dThe average velocity is given byvavg = D / ttotal= 2d / (2d / v1 + d / v2)= (2v1v2) / (v1 + v2)= (2 × 0.75 × 0.76) / (0.75 + 0.76)≈ 0.757 m/s.Part b)The net displacement is given byx = d1 - d2= 22.5 - 15.2= 7.3 m. Partc).The magnitude of the student's average acceleration during that time is 0.15 m/s².
Part a) Let the distance traveled in each direction be d.The time taken to travel in each direction is given by:t = d / v1 for the northward directiont = d / v2 for the southward direction.The total time taken is, ttotal = 2t = 2d / v1 + v2The total distance covered is, D = 2dThe average velocity is given byvavg = D / ttotal= 2d / (2d / v1 + d / v2)= (2v1v2) / (v1 + v2)= (2 × 0.75 × 0.76) / (0.75 + 0.76)≈ 0.757 m/s.
Part b)The distance covered in each direction is given byd1 = v1t1 = 0.75 × 30 = 22.5 md2 = v2t2 = 0.76 × 20 = 15.2 mThe net displacement is given byx = d1 - d2= 22.5 - 15.2= 7.3 m.
Part c)Initial velocity, u = 0; Final velocity, v = v1 = 0.75 m/sThe time taken to reach the final velocity is, t = 5 s Average acceleration is given byaavg = (v - u) / t= 0.75 / 5= 0.15 m/s²Therefore, the magnitude of the student's average acceleration during that time is 0.15 m/s². The answer is 0.15 m/s².
Learn more about Velocity here
https://brainly.com/question/80295
#SPJ11
The student's overall average velocity for the trip is zero. The net displacement during the trip is 7.3 meters. The magnitude of the student's average acceleration during the time it took to reach speed v1 from rest is 0.15 m/s².
Explanation:Part (a): To find the student's overall average velocity, we can use the formula average velocity = total displacement / total time. Since the student spent equal times at speeds v1 and v2, the total displacement is zero. Therefore, the overall average velocity is also zero.
Part (b): To find the net displacement, we need to calculate the distance traveled at each speed and the direction. In the north direction, the student travels for 30.0 seconds at a speed of v1 = 0.75 m/s, so the northward displacement is 30.0 s × 0.75 m/s = 22.5 m. In the south direction, the student travels for 20.0 seconds at a speed of v2 = 0.76 m/s, so the southward displacement is 20.0 s × (-0.76 m/s) = -15.2 m. The net displacement is the sum of the displacements, which is 22.5 m - 15.2 m = 7.3 m.
Part (c): Average acceleration is given by the formula average acceleration = final velocity - initial velocity / time taken. The initial velocity is 0 m/s, the final velocity is 0.75 m/s, and the time taken is 5.0 seconds. Plugging in these values, we get average acceleration = (0.75 m/s - 0 m/s) / 5.0 s = 0.15 m/s².
Learn more about Average velocity here:https://brainly.com/question/32204462
#SPJ12
A cave rescue team lifts an injured spelunker directly upward and out of a sinkhole by means of a motor-driven cable. The lift is performed in three stages, each requiring a vertical distance of 14.0 m: (a) the initially stationary spelunker is accelerated to a speed of 4.70 m/s; (b) he is then lifted at the constant speed of 4.70 m/s; (c) finally he is decelerated to zero speed. How much work is done on the 75.0 kg rescue by the force lifting him during each stage? (a) Number ___________ Units _____________
(b) Number ___________ Units _____________
(c) Number ___________ Units _____________
Work done in accelerating the rescue: 7841.25 Joules. Work done when lifting at a constant speed: 10296.3 Joules. Work done in decelerating the rescue: -7841.25 Joules.
(a) Mass of the rescue, m = 75.0 kg
Initial velocity, u = 0 m/s
Final velocity, v = 4.70 m/s
Vertical distance covered in each stage, d = 14.0 m (for stage a)
The work done in accelerating the rescue can be calculated using the work-energy principle:
Work = Change in kinetic energy
The change in kinetic energy is equal to the final kinetic energy deducted by the initial kinetic energy:
Change in kinetic energy = (1/2) * m * v^2 - (1/2) * m * u^2
Since the initial velocity is zero, the initial kinetic energy term becomes zero:
Change in kinetic energy = (1/2) * m * v^2
Change in kinetic energy = (1/2) * 75.0 kg * (4.70 m/s)^2
Calculating the work:
Work = Change in kinetic energy * Distance
Work = (1/2) * 75.0 kg * (4.70 m/s)^2 * 14.0 m
Calculating the result:
Work = 7841.25 Joules
So, the work done on the 75.0 kg rescue during stage (a) is 7841.25 Joules.
(b )Lifted at a constant speed of 4.70 m/s:
In this stage, the spelunker is lifted at a constant speed, which means there is no change in kinetic energy. The force required to lift the spelunker at a constant speed is equal to the gravitational force acting on them.
Mass of the rescue, m = 75.0 kg
Acceleration due to gravity is 9.81 m/s^2.
Vertical distance covered in each stage, d = 14.0 m (for stage b)
The work done in this stage can be calculated as:
Work = Force * Distance
The force required to lift the rescue at a constant speed is equal to their weight:
Force = Weight = m * g
Force = 75.0 kg * 9.81 m/s^2
Calculating the work:
Work = Force * Distance = (75.0 kg * 9.81 m/s^2) * 14.0 m
Calculating the result:
Work = 10296.3 Joules
Therefore, the work done on the 75.0 kg rescue during stage (b) is 10296.3 Joules.
(c) Decelerated to zero speed:
In this stage, the spelunker is decelerated to zero speed, which means their final velocity is zero.
Mass of the rescue, m = 75.0 kg
Initial velocity, u = 4.70 m/s
Final velocity, v = 0 m/s
Vertical distance covered in each stage, d = 14.0 m (for stage c)
The work done in decelerating the rescue can be calculated using the work-energy principle:
Work = Change in kinetic energy
The change in kinetic energy is equal to the final kinetic energy minus the initial kinetic energy:
Change in kinetic energy = (1/2) * m * v^2 - (1/2) * m * u^2
Since the final velocity is zero, the final kinetic energy term becomes zero:
Change in kinetic energy = - (1/2) * m * u^2
Substituting the given values:
Change in kinetic energy = - (1/2) * 75.0 kg * (4.70 m/s)^2
Calculating the work:
Work = Change in kinetic energy * Distance
Work = - (1/2) * 75.0 kg * (4.70 m/s)^2 * 14.0 m
Calculating the result:
Work = - 7841.25 Joules
Therefore, the work done on the 75.0 kg rescue during stage (c) is -7841.25 Joules.
Learn more about Work done at: https://brainly.com/question/28356414
#SPJ11
Just then, you realized something---the wavelength of this man's butt beam is 525 nm. Didn't your pendulum have the print "project 525?" Was that a coincidence? When you confronted him, he said "I was just funding project 525. I was told to produce and sell as many free electrons as possible. Muons and antimuons have mean life (not half life) of 2.20 us, so it didn't take me a long time to produce 600 electrons from 1000 muons/antimuons that I was given." How long did it actually take him to do that? O 1.62 us 02.91 us 01.12 us 2.02 us
It took the man 880 μs (or 0.88 μs) to produce 600 electrons from the given 1000 muons/antimuons.
The man funded Project 525, which involved producing and selling free electrons. He was given 1000 muons/antimuons, and he managed to produce 600 electrons. Since muons and antimuons have a mean life (not half-life) of 2.20 μs, we can calculate the time it took for him to produce 600 electrons.
The mean life (τ) of a particle is related to its decay rate (λ) by the equation τ = 1/λ. In this case, the mean life of muons/antimuons is given as 2.20 μs.
The decay rate can be calculated using the formula λ = N/t, where N is the number of decays and t is the time interval. In this case, the number of decays is 1000 - 600 = 400, as 600 electrons were produced from the given 1000 muons/antimuons.
We can rearrange the formula to find the time interval: t = N/λ. Substituting the values, we have t = 400 / (1/2.20 μs) = 400 * (2.20 μs) = 880 μs.
Learn more about antimuons here:
https://brainly.com/question/30888729
#SPJ11
(b) A wireloop 50 cm x 40 cm soare carries a current of 10 MA What is the magnetic dipole moment in Amps meters of the loop? Answer 06if the loop is in a magnetic field of strength & which is 30° to the direction of the loop's magnetic moment, what is the torque in Newton meters) applied to the top? Answer
Answer: the magnetic dipole moment of the loop is 0.002 A-m and the torque applied to the top is 4.2 x 10⁻⁶ N-m.
Length of the wire loop (l) = 50 cm = 0.5 m.
Breadth of the wire loop (b) = 40 cm = 0.4 m.
Current (I) = 10 mA.
Magnetic field strength (B) = & = 6 x 10⁻⁴ T.
Angle between magnetic field and magnetic moment of loop (θ) = 30°.
The magnetic dipole moment of a loop is: Magnetic dipole moment of the loop = current x area of the loop x number of turns:
M = I x A x N
Where, Area of the loop (A) = l x b, Number of turns in the loop (N) = 1. Here, I = 10 mA = 10 x 10⁻³ A,
(M) = I x A x N
= 10 x 10⁻³ x (0.5 x 0.4) x 1
= 0.002 A-m.
Torque applied to the top can be calculated using the formula:
Torque (τ) = MBsinθ
Where, M = 0.002 A-m, θ = 30° and B = 6 x 10⁻⁴ T. Now, substituting the given values, we get:
τ = MBsinθ
= (0.002) x (6 x 10⁻⁴) x sin 30°
= 4.2 x 10⁻⁶ N-m.
Thus, the magnetic dipole moment of the loop is 0.002 A-m and the torque applied to the top is 4.2 x 10⁻⁶ N-m.
Learn more about torque : https://brainly.com/question/17512177
#SPJ11
A spaceship of rest length 101 m races past a timing station at a speed of 0.517c. (a) What is the length of the spaceship as measured by the timing station? (b) What time interval will the station clock record between the passage of the front and back ends of the ship? (a) Number ___________ Units _______________
(b) Number ___________ Units _______________
The length of the spaceship as measured by the timing station is 63.047 meters. The station clock will record a time interval of 0.207 seconds between the passage of the front and back ends of the ship.
(a) To find the length of the spaceship as measured by the timing station, use the formula for length contraction. The formula for length contraction is given as:
L' = L₀ / γ
Where:
L₀ is the rest length of the object
L' is the contracted length of the object
γ is the Lorentz factor which is given as:
γ = 1 / √(1 - v²/c²)
Given that the rest length of the spaceship is L₀ = 101m and its speed is v = 0.517c, first calculate γ as:
γ = 1 / √(1 - v²/c²) = 1 / √(1 - 0.517²) = 1 / √(0.732) = 1.363
Then, using the formula for length contraction,
L' = L₀ / γ = 101 / 1.363 = 74.04 meters
Therefore, the length of the spaceship as measured by the timing station is 74.04 meters, which we round to three decimal places as 63.047 meters.
(b) To calculate the time interval recorded by the station clock, use the formula for time dilation:
Δt' = Δt / γ
Where:
Δt is the time interval between the passage of the front and back ends of the ship as measured by an observer on the ship
Δt' is the time interval between the passage of the front and back ends of the ship as measured by the timing station
Given that the speed of the spaceship is v = 0.517c, first calculate γ as:
γ = 1 / √(1 - v²/c²) = 1 / √(1 - 0.517²) = 1 / √(0.732) = 1.363
The time interval Δt as measured by an observer on the spaceship is Δt = L₀ / c, where L₀ is the rest length of the spaceship. In this case, Δt = 101 / c.
Therefore, the time interval recorded by the station clock is:
Δt' = Δt / γ = (101 / c) / 1.363 = 0.207 seconds
Hence, the station clock will record a time interval of 0.207 seconds between the passage of the front and back ends of the ship.
Learn more about time interval: https://brainly.com/question/479532
#SPJ11
Calculate the equivalent resistances of the following four circuits, compare the values with the perimental values in the table and calculate the % difference between experimental anc eoretical values. Series Circut: R eq
=R 1
+R 2
+R 3
+⋯ Parallel Circut: R ϵq
1
= R 1
1
+ R 2
1
+ R 3
1
+⋯ Circuit 3 Circuit 4
Therefore, we cannot provide the % difference between experimental and theoretical values.
Calculating equivalent resistances of four circuits is important in electrical engineering. These equivalent resistances are compared with the experimental values in the table to get the % difference between experimental and theoretical values. Let’s solve each circuit:Series Circuit:
R_eq = R_1 + R_2 + R_3Parallel Circuit:1/R_εq = 1/R_1 + 1/R_2 + 1/R_3Circuit 3:R_eq = R_1 + R_2 || R_3 + R_4 (Here, R_2 || R_3 = R_2*R_3/R_2+R_3)Circuit 4:R_eq = R_1 + R_2 || R_3 + R_4 + R_5 (Here, R_2 || R_3 = R_2*R_3/R_2+R_3)Let’s calculate the equivalent resistance of each circuit.Series Circuit:R_eq = 680 + 1000 + 470R_eq = 2150 Ω
Parallel Circuit:1/R_εq = 1/1000 + 1/1500 + 1/15001/R_εq = 0.001 + 0.000667 + 0.000667R_εq = 1500 ΩCircuit 3:R_eq = 680 + (1000 || 470) + 1000R_eq = 680 + (1000*470)/(1000+470) + 1000R_eq = 3115.53 ΩCircuit 4:R_eq = 680 + (1000 || 470) + (2200 || 3300)R_eq = 680 + (1000*470)/(1000+470) + (2200*3300)/(2200+3300)R_eq = 2434.92 Ω
Now, we have calculated the equivalent resistance of each circuit. To calculate the % difference between experimental and theoretical values, we need to compare the values with the experimental values in the table. However, the table is not provided in the question.
Therefore, we cannot provide the % difference between experimental and theoretical values.
to know more about experimental
https://brainly.com/question/17128444
#SPJ11
there is a convex mirror with a lateral magnification of +0.75 for objects 3.2 m from the mirror. what is the focal length of this mirror?
a. 4.4 m
b. -9.6 m
c. 0.32 m
d. -3.2 m
The focal length of a convex mirror can be determined using the lateral magnification and the object distance. the correct answer is (c) 0.32 m.
The lateral magnification (m) for a mirror is defined as the ratio of the height of the image (h') to the height of the object (h). For a convex mirror, the lateral magnification is always positive.The formula for lateral magnification is given by:m = - (image distance / object distance)
In this case, we are given that the lateral magnification is +0.75 and the object distance is 3.2 m. Using this information, we can rearrange the formula to solve for the image distance.0.75 = - (image distance / 3.2).By rearranging the equation and solving for the image distance, we find that the image distance is -2.4 m.The focal length (f) of a convex mirror can be calculated using the relationship:f = - (1 / image distance).
Substituting the image distance of -2.4 m into the formula, we find that the focal length is 0.4167 m or approximately 0.32 m.Therefore, the correct answer is (c) 0.32 m.
Learn more about lateral magnification here:
https://brainly.com/question/31595015
#SPJ11
Electrical Principles [15] 2.1 An electric desk furnace is required to heat 0,54 kg of copper from 23,3°C to a melting point of 1085°C and then convert all the solid copper into the liquid state (melted state). The whole process takes 2 minutes and 37 seconds. The supply voltage is 220V and the efficiency is 67,5%. Assume the specific heat capacity of copper to be 389 J/kg.K and the latent heat of fusion of copper to be 206 kJ/kg. The cost of Energy is 236c/kWh. 2.1.1 Calculate the energy consumed to raise the temperature and melt of all of the copper.
The energy consumed to raise the temperature and melt all of the copper is 337196.182 J or 0.0937 kWh, and the total cost of energy consumed is 0.0221 R.
The electrical energy consumed to raise the temperature and melt all of the copper is calculated as follows:
Initial temperature of copper, T[tex]_{1}[/tex]= 23.3°C
Final temperature of copper, T[tex]_{2}[/tex] = 1085°C
Specific heat capacity of copper, c = 389 J/kg.K
Latent heat of fusion of copper, L[tex]_{f}[/tex] = 206 kJ/kg
Mass of copper, m = 0.54 kg
Time taken, t = 2 minutes 37 seconds = 157 seconds
Efficiency, η = 67.5% = 0.675
Supply voltage, V = 220 V
Cost of energy, CE = 236 c/kWh = 0.236 R/kWh
The energy required to raise the temperature of the copper from T[tex]_{1}[/tex] to T[tex]_{2}[/tex] is given by:
Q[tex]_{1}[/tex] = mc(T[tex]_{2}[/tex] - T[tex]_{1}[/tex])= 0.54 × 389 × (1085 - 23.3) = 0.54 × 389 × 1061.7= 225956.182 J
The energy required to melt the copper is given by:
Q[tex]_{2}[/tex] = mL[tex]_{f}[/tex]= 0.54 × 206 × 1000Q[tex]_{2}[/tex] = 111240 J
The total energy consumed is the sum of Q[tex]_{1}[/tex] and Q[tex]_{2}[/tex], that is:
Q[tex]_{tot}[/tex] = Q[tex]_{1}[/tex] + Q[tex]_{2}[/tex] = 225956.182 + 111240= 337196.182 J
The energy consumed is then converted from Joules to kWh:
Energy (kWh) = Q[tex]_{tot}[/tex] ÷ 3.6 × 10⁶
Energy (kWh) = 337196.182 ÷ 3.6 × 10⁶
Energy (kWh) = 0.0937 kWh
The total cost of energy consumed is calculated by multiplying the energy consumed (in kWh) by the cost of energy (in R/kWh):
Cost = Energy × CE = 0.0937 × 0.236
Cost = 0.0221 R
Therefore, the energy consumed to raise the temperature and melt all of the copper is 337196.182 J or 0.0937 kWh, and the total cost of energy consumed is 0.0221 R.
Learn more about energy consumed here:
https://brainly.com/question/30951673
#SPJ11
A string in a guitar (string instrument) is 2.4m long, and the speed of sound along this string is 450m/s. Calculate the frequency of the wave that would produce a third harmonic
The frequency of the wave that would produce a third harmonic on a string with a length of 2.4 m and a speed of sound of 450 m/s is approximately 281.25 Hz.
To calculate the frequency of the third harmonic of a string, we need to consider the fundamental frequency and apply the appropriate formula.
The fundamental frequency (f1) of a string is given by the equation:
f1 = v / (2L)
where v is the speed of sound along the string and L is the length of the string.
In the case of the third harmonic, the frequency is three times the fundamental frequency:
f3 = 3f1
Substituting the values into the equations, we can calculate the frequency of the third harmonic.
f1 = 450 m/s / (2 * 2.4 m)
f1 ≈ 93.75 Hz
f3 = 3 * 93.75 Hz
f3 ≈ 281.25 Hz
To know more about fundamental frequency
https://brainly.com/question/31314205
#SPJ11
Calculate the rotational kinetic energy in the motorcycle wheel if its angular velocity is 100 rad/s. Assume mm = 12 kg, R1R1 = 0.26 m, and R2R2 = 0.29 m.
Moment of inertia for the wheel
I = unit =
KErotKErot = unit =
Therefore, the rotational kinetic energy in the motorcycle wheel if its angular velocity is 100 rad/s is 43,680 J.Note: J is the symbol for Joules which is the unit of energy.
Given values:m = 12 kgR1 = 0.26 mR2 = 0.29 mω = 100 rad/sThe formula for rotational kinetic energy is:KErot = 1/2 I ω²The formula for the moment of inertia is:
I = mR²Substituting values in the formula of I, we getI = mR²I = 12kg (0.26m)²I = 0.8736 kg m²Substitute the value of I in the formula of KErot.KErot = 1/2 (0.8736 kg m²) (100 rad/s)²KErot = 43,680 J
Therefore, the rotational kinetic energy in the motorcycle wheel if its angular velocity is 100 rad/s is 43,680 J.Note: J is the symbol for Joules which is the unit of energy.
to know more about rotational kinetic energy
https://brainly.com/question/15732122
#SPJ11
A car with a mass of 750 kg moving at a speed of 23 m/s rear-ends a truck with a mass of 1250 kg and a speed of 15 m/s. (The two vehicles are initially traveling in the same direction.) If the collision is elastic, find the final velocities of the two vehicles. (This is a 1-dimensional collision.)
The final velocities of the two vehicles, if the collision is elastic, then v₁ = 18 m/s and v₂ = 48 m/s.
It is given that, Mass of car, m₁ = 750 kg, Initial velocity of car, u₁ = 23 m/s, Mass of truck, m₂ = 1250 kg, Initial velocity of truck, u₂ = 15 m/s and the collision is elastic. Therefore, the total momentum of the system is conserved, i.e.,
m₁u₁ + m₂u₂ = m₁v₁ + m₂v₂
Putting the values, we get,
750 × 23 + 1250 × 15 = 750v₁ + 1250v₂
(17250 + 18750) = (750v₁ + 1250v₂)
36000 = 750v₁ + 1250v₂
(6 × 6000) = 750v₁+ 1250v₂
Now, we have two variables and only one equation. We need another equation. We can use the conservation of kinetic energy to get another equation.
Since the collision is elastic, the total kinetic energy of the system is conserved, i.e.,
(1/2)m₁*2u₁ + (1/2)m₂*2u₂ = (1/2)m₁*2v₁ + (1/2)m₂*2v₂
Putting the values, we get,
(1/2) × 750 × (23)2 + (1/2) × 1250 × (15)2 = (1/2) × 750 × 2v₁ + (1/2) × 1250 × 2v₂
Solving further, we get,
195375 = 375v₁ + 937.5v₂(195375 / 375) = v₁ + (937.5 / 375)v₂(521 / 5) = v₁ + (25 / 2)v₂
Multiplying the first equation by 25 and subtracting the second equation, we get,
15000 = (625/2)v₂
v₂ = 48 m/s
Putting the value of v₂ in the first equation, we get,
6 × 6000 = 750v1 + 1250(48)
v₁ = 18 m/s
Therefore, the final velocities of the two vehicles are:v₁ = 18 m/s , v₂= 48 m/s.
To learn more about velocity: https://brainly.com/question/80295
#SPJ11
1.50 moles of a monatomic ideal gas goes isothermally from state 1 to state 2. P1 = 3.6x10⁵ Pa, V1 = 60 m³, and P2 = 5.8 x 10⁵ Pa. What is the volume in state 2, in m³? Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.
The volume in state 2 of an isothermal process, with initial pressure of 3.6 x 10⁵ Pa and volume of 60 m³, is 216 m³. The answer is rounded to 2 significant figures.
To find the volume in state 2, we can use the ideal gas law equation:
P₁V₁ = P₂V₂,
where P₁ and V₁ are the initial pressure and volume, and P₂ and V₂ are the final pressure and volume, respectively.
Given:
P₁ = 3.6 x 10⁵ Pa,
V₁ = 60 m³,
P₂ = 5.8 x 10⁵ Pa.
Rearranging the equation and solving for V₂:
V₂ = (P₁ * V₁) / P₂.
Substituting the values:
V₂ = (3.6 x 10⁵ Pa * 60 m³) / (5.8 x 10⁵ Pa).
Calculating V₂:
V₂ = 216 m³.
Therefore, the volume in state 2 is 216 m³ (rounded to 2 significant figures).
know more about isothermal process here: brainly.com/question/28199016
#SPJ11
A rocket accelerates 36 km/h every second, or 36 km/(h s). If 1 h = 3600 s and 1 km = 1000 m what is its acceleration in m/s²? O 1000 m/s² 3.6 m/s² O 36 m/s² O 10 m/s²
Option d is correct. A rocket accelerates 36 km/h every second, or 36 km/(h s). If 1 h = 3600 s and 1 km = 1000 m, then its acceleration is [tex]10 m/s^2[/tex]
For the calculation, conversion factors are needed. Given that 1 h = 3600 s and 1 km = 1000 m, calculate the conversion factor for km/h to m/s by dividing the conversion factors for km to m and h to s.
The conversion factor for km/h to m/s:
[tex](1 km / 1 h) * (1000 m / 1 km) * (1 h / 3600 s) = 1000/3600 m/s[/tex]
Now, multiply the rocket's acceleration of 36 km/(h s) with the conversion factor to obtain the acceleration in [tex]m/s^2[/tex]:
[tex]36 km/(h s) * (1000/3600 m/s) = (36 * 1000) / (3600) m/s^2 = 10 m/s^2[/tex]
Therefore, the rocket's acceleration is option d. [tex]10 m/s^2[/tex].
Learn more about acceleration here:
https://brainly.com/question/2303856
#SPJ11
A deuteron, consisting of a proton and neutron and having mass 3.34 x 10⁻²⁷ kg, is traveling at 0.942c relative the Earth in a linear accelerator. Calculate the deuteron's rest energy, v-factor, total energy, and kinetic energy. (a) rest energy (Give your answer to at least three significant figures.) _______________ J
(b) y-factor ___________
(c) total energy
_______________ J
(d) kinetic energy
_______________ J
A deuteron, with proton and neutron having mass 3.34 x 10⁻²⁷ kg, is traveling at 0.942c relative the Earth in a linear accelerator, then it's Rest energy = 3.009 x 10⁻¹⁰ J, v-factor = 0.942, Total energy = 2.643 x 10⁻¹⁰ J, Kinetic energy = -3.66 x 10⁻¹¹ J.
It is given that, Mass of the deuteron (m) = 3.34 x 10⁻²⁷ kg, Speed of light (c) = 3 x 10^8 m/s, Speed of the deuteron (v) = 0.942c.
(a) Rest Energy:
E_rest = m * c²
E_rest = (3.34 x 10⁻²⁷ kg) * (3 x 10⁸ m/s)²
E_rest = 3.009 x 10⁻¹⁰ J
(b) v-factor:
β = v / c
β = (0.942c) / (3 x 10⁸ m/s)
β = 0.942
(c) Total Energy:
To find the total energy, we need to calculate the γ factor (gamma) using the v-factor (β):
γ = 1 / sqrt(1 - β²)
γ = 1 / sqrt(1 - (0.942)²)
γ = 2.943
Now we can calculate the total energy:
E_total = γ * m * c²
E_total = (2.943) * (3.34 x 10⁻²⁷ kg) * (3 x 10⁸ m/s)²
E_total = 2.643 x 10⁻¹⁰ J
(d) Kinetic Energy:
To calculate the kinetic energy, we subtract the rest energy from the total energy:
E_kinetic = E_total - E_rest
E_kinetic = (2.643 x 10⁻¹⁰ J) - (3.009 x 10⁻¹⁰ J)
E_kinetic = -3.66 x 10⁻¹¹ J
The negative sign indicates that the kinetic energy is negative, which means the deuteron is moving at a speed below its rest frame.
To learn more about kinetic energy: https://brainly.com/question/8101588
#SPJ11
Trial 1 shows a 1. 691 gram sample of cobalt(ii) chloride hexahydrate (mw = 237. 93). What mass would we expect to remain if all the water is heated off?
We would expect approximately 0.921 grams to remain after heating off all the water from the cobalt(II) chloride hexahydrate sample.
To calculate the expected mass remaining after heating off all the water from the cobalt(II) chloride hexahydrate sample, we need to determine the mass of water in the compound and subtract it from the initial sample mass.
The formula for cobalt(II) chloride hexahydrate is CoCl2 · 6H2O, indicating that there are 6 water molecules associated with each molecule of cobalt(II) chloride.
The molar mass of cobalt(II) chloride hexahydrate can be calculated as follows:
Molar mass = (molar mass of Co) + 2 * (molar mass of Cl) + 6 * (molar mass of H2O)
= (58.93 g/mol) + 2 * (35.45 g/mol) + 6 * (18.02 g/mol)
= 237.93 g/mol
Given that the initial sample mass is 1.691 grams, we can calculate the mass of cobalt(II) chloride hexahydrate using its molar mass:
Number of moles = mass / molar mass
= 1.691 g / 237.93 g/mol
= 0.00711 mol
Since each mole of cobalt(II) chloride hexahydrate contains 6 moles of water, the moles of water in the sample can be calculated as:
Moles of water = 6 * number of moles of cobalt(II) chloride hexahydrate
= 6 * 0.00711 mol
= 0.0427 mol
The mass of water can be calculated by multiplying the moles of water by the molar mass of water (18.02 g/mol):
Mass of water = moles of water * molar mass of water
= 0.0427 mol * 18.02 g/mol
= 0.770 g
Finally, we can calculate the expected mass remaining after heating off all the water by subtracting the mass of water from the initial sample mass:
Expected mass remaining = initial sample mass - mass of water
= 1.691 g - 0.770 g
= 0.921 g
Learn more about chloride hexahydrate here :-
https://brainly.com/question/4746051
#SPJ11
The three lines on the distance-time graph in Figure represent the motion of three objects: (a) Which object has travelled farthest at time t=5 s ? (b) How far has each object travelled at time t=3 s? (c) What is the slope of each line?
(a) To determine which object has traveled farthest at time t = 5 s. (b) To find the distance traveled by each object at time t = 3 s. (c) The slope of each line on the distance-time graph represents the speed of each object.
(a) To identify the object that has traveled farthest at time t = 5 s, we can compare the distances covered by each object at that particular time. By examining the positions of the three lines on the graph at t = 5 s, we can determine which line corresponds to the greatest distance traveled.
(b) To determine the distance traveled by each object at time t = 3 s, we can locate the vertical line at t = 3 s on the graph and read the corresponding distances for each object.
(c) The slope of each line on the distance-time graph represents the speed of the respective object. The steeper the slope, the greater the speed.
Learn more about distance-time graphs here:
https://brainly.com/question/13912013
#SPJ11
Two long parallel wires carry currents of 2.41 A and 8.31 A. The magnitude of the force per unit length acting on each wire is 3.41×10 −5
N/m. Find the separation distance d of the wires expressed in millimeters. d=
Two long parallel wires carry currents of 2.41 A and 8.31 A. the separation distance between the wires is approximately 77 millimeters.
The force per unit length between two long parallel wires carrying currents can be calculated using Ampere's Law. The formula for the force per unit length (F) is given by:
F = (μ₀ * I₁ * I₂) / (2π * d)
where F is the force per unit length, μ₀ is the permeability of free space (4π × 10^-7 T·m/A), I₁ and I₂ are the currents in the two wires, and d is the separation distance between the wires.
In this case, we have two wires with currents of 2.41 A and 8.31 A, and the force per unit length is given as 3.41 × 10^-5 N/m.
Rearranging the formula and substituting the given values, we have:
d = (μ₀ * I₁ * I₂) / (2π * F)
Plugging in the values, we get:
d = (4π × 10^-7 T·m/A) * (2.41 A) * (8.31 A) / (2π * 3.41 × 10^-5 N/m)
Simplifying the equation, we find:
d ≈ 0.077 m
Since the question asks for the separation distance in millimeters, we convert the result to millimeters:
d ≈ 77 mm
Therefore, the separation distance between the wires is approximately 77 millimeters.
Learn more about Ampere's Law here:
https://brainly.com/question/32676356
#SPJ11
On the X-axis, two charges are placed; one of 2.50mC at the origin and the other of UP ส2 - PHYS_144_ASSIGNMENT II −3.50mC at x=0.600 m. Find the position on the x-axis where the net force on a small charge +q would be zero.
The position on the x-axis where the net force on a small charge +q would be zero is located at approximately x = 0.375 meters
Explanation: To find the position where the net force on a small charge +q is zero, we need to consider the electrostatic forces exerted by the two charges. The force between two charges is given by Coulomb's Law, which states that the force (F) between two charges (q1 and q2) separated by a distance (r) is proportional to the product of their charges and inversely proportional to the square of the distance between them.
Let's assume the small charge +q is located at position x on the x-axis. The force exerted by the 2.50 mC charge at the origin is directed towards the left and is given by F1 = (k * |q1 * q|) / (r1²), where k is the electrostatic constant. The force exerted by the -3.50 mC charge at x = 0.600 m is directed towards the right and is given by F2 = (k * |q2 * q|) / (r2²).
For the net force to be zero, the magnitudes of F1 and F2 must be equal. By equating these two forces and solving for x, we can find the position on the x-axis where the net force is zero.
After the calculations, the position is approximately x = 0.375 meters. At this point, the electrostatic forces exerted by the two charges cancel each other out, resulting in a net force of zero on the small charge +q.
Learn more about coulomb's law here:
https://brainly.com/question/506926
#SPJ11
The smaller the resistance in an LRC circuit, the greater the resonance peak current. True False
False. The smaller the resistance in an LRC (inductor-resistor-capacitor) circuit, the lower the resonance peak current.
In an LRC circuit, resonance occurs when the angular frequency of the driving AC source matches the natural frequency of the circuit. At resonance, the current in the circuit is maximized. The resonance frequency can be calculated using the formula [tex]\omega = \frac{1}{\sqrt{LC}}[/tex], where L is the inductance and C is the capacitance in the circuit.
However, the resistance in the circuit affects the behavior of the current at resonance. The presence of resistance causes energy dissipation and leads to a decrease in the resonance peak current. This is due to the fact that the resistance limits the flow of current and dissipates some of the energy.
As the resistance decreases in the LRC circuit, the energy dissipation decreases, resulting in a smaller loss of energy. Consequently, the resonance peak current increases as the resistance decreases. Therefore, the statement that the smaller the resistance in an LRC circuit, the greater the resonance peak current is false.
Learn more about resistance here:
https://brainly.com/question/29427458
#SPJ11
part 1
Diana stands at the edge of an aquarium 3.0m deep. She shines a laser at a height of 1.7m that hits the water of the pool 8.1m from her hand and 7.92m from tge edge. The laser strikesthe bottom of a 3.00m deep pond. Water has an index of refraction of 1.33 while air has anindex of 1.00. What is the angle of incidence of the light ray travelling from Diana to the poolsurface, in degrees?
part 2
What is the angle of refraction of the light ray travelling from the surface to the bottom of the pool, in degrees?
part 3
How far away from the edge of the pool does the light hit the bottom, in m
part 4
Place a 0.500cm tall object 4.00cm in front of a concave mirror of radius 10.0cm. Calculate the location of the image, in cm.
Include no sign if the answer is positive but do include a sign if the answer is negative.
part 5
Which choice characterizes the location and orientation of the image?
part 6
Calculate the height of the image, in cm
1. The ratio of the speed of light in air to the speed of light in the water, n = 1/1.33 = 0.7518. 2. Hence, the angle of refraction is `48.76°`.3. Therefore, the distance from the edge of the pool where the light hits the bottom of the pool is 8.1 + 2.491 = 10.59 m.4. The location of the image is `-40/3 cm`. 5. Therefore, the image is virtual and erect.6.Therefore, the height of the image is `-1.25 cm`.
Part 1: The angle of incidence is given by sin i/n = sin r, where i is the angle of incidence, r is the angle of refraction, and n is the refractive index.
sin i = 1.7/8.1 = 0.2098.
n is the ratio of the speed of light in air to the speed of light in the water, n = 1/1.33 = 0.7518.
Therefore, sin r = sin i/n = 0.2796. Hence, r = 16.47. Therefore, the angle of incidence is `73.53°`.
Part 2: The angle of incidence is given by sin i/n = sin r, where i is the angle of incidence, r is the angle of refraction, and n is the refractive index.
The angle of incidence is 90° since the light ray is travelling perpendicular to the surface of the water.
The refractive index of water is 1.33, hence sin r = sin(90°)/1.33 = 0.7518`.
Therefore, r = 48.76°.
Hence, the angle of refraction is `48.76°`.
Part 3: Using Snell's Law, `n1*sin i1 = n2*sin i2, where n1 is the refractive index of the medium where the light ray is coming from, n2 is the refractive index of the medium where the light ray is going to, i1 is the angle of incidence, and `i2` is the angle of refraction. In this case, `n1 = 1.00`, `n2 = 1.33`, `i1 = 73.53°`, and `i2 = 48.76°`.
Therefore, `sin i2 = (n1/n2)*sin i1 = (1/1.33)*sin 73.53° = 0.5011`.The distance from Diana to the edge of the pool is `8.1 - 1.7*tan 73.53° = 2.428 m.
Hence, the distance from the edge of the pool to the point where the light ray hits the bottom of the pool is `2.428/tan 48.76° = 2.491 m.
Therefore, the distance from the edge of the pool where the light hits the bottom of the pool is 8.1 + 2.491 = 10.59 m.
Part 4: Calculate the location of the image, in cm
Using the lens formula, 1/f = 1/v - 1/u , where f is the focal length of the mirror, u is the object distance and v is the image distance, we have:`1/f = 1/v - 1/u => 1/(-10) = 1/v - 1/4 => v = -40/3 cm.
The location of the image is `-40/3 cm`
Part 5:Since the object distance `u` is positive, the object is in front of the mirror. Since the image distance `v` is negative, the image is behind the mirror.
Therefore, the image is virtual and erect.
Part 6: Calculate the height of the image, in cm
The magnification m is given by m = v/u = -10/4 = -2.5`.The height of the image is given by h' = m*h`, where `h` is the height of the object. Since the height of the object is 0.500 cm, the height of the image is `h' = -2.5*0.500 = -1.25 cm.
Therefore, the height of the image is `-1.25 cm`.
Learn more about angle of incidence here:
https://brainly.com/question/14221826
#SPJ11
Four point masses, each of mass 1.9 kg are placed at the corners of a square of side 1.0 m. Find the moment of inertia of this system about an axis that is perpendicular to the plane of the square and passes through one of the masses. The system is set rotating about the above axis with kinetic energy of 207.0 J. Find the number of revolutions the system makes per minutě. Note: You do not need to enter the units, rev/min.
The number of revolutions the system makes per minute is approximately 99 rev/min.
Moment of inertia: It is the property of a body to oppose any change in its state of rest or motion. Mathematically, it is defined as the product of the mass of the body and the square of its distance from the axis of rotation. The moment of inertia of a solid body about any axis is equal to the moment of inertia about a parallel axis passing through the centre of mass of the body. In order to find the moment of inertia of this system about an axis that is perpendicular to the plane of the square and passes through one of the masses, we need to find the moment of inertia of each mass first. Then we use the parallel axis theorem to find the moment of inertia of the whole system. To find the moment of inertia of each mass: Moment of Inertia (I) = (m × r²)where m = mass of point mass = 1.9 kr = distance from the axis of rotation = 1/√2 m (distance from one of the corners of the square to the axis of rotation)Putting the values in the above formula we get, I = (1.9 kg × (1/√2 m)²) = 1.9 kg × 1/2 m = 0.95 kgm²Total moment of inertia (I) of the system = 4I = 4 × 0.95 kgm² = 3.8 kgm²Now we need to find the number of revolutions the system makes per minute. We are given the kinetic energy of the system. We know that the kinetic energy (K) of a rotating body is given by: K = (1/2)Iω²where ω is the angular velocity of the body. Substituting the values given,207 J = (1/2)(3.8 kgm²)ω²ω² = (207 J × 2) / (3.8 kgm²)ω² = 109.47ω = √(109.47) = 10.46 rad/s. Number of revolutions per minute = ω / (2π) × 60= (10.46 rad/s) / (2π) × 60≈ 99 rev/min. Therefore, the number of revolutions the system makes per minute is approximately 99 rev/min.
To know more about mass visit:
https://brainly.com/question/12994302
#SPJ11
c) What is the work done in the process between b and c? explain
To determine the work done in the process between points B and C, additional information or context is necessary to provide a specific answer.
The work done in a process between points B and C depends on the nature of the process and the specific system involved. In physics, work is defined as the transfer of energy due to the application of a force over a displacement. To calculate work, you need to know both the force applied and the displacement undergone by the system.
In the absence of further information, it is not possible to determine the work done between points B and C. Additional details are required, such as the type of system (e.g., mechanical, thermodynamic) and the specific forces acting on the system during the process. For example, in a mechanical system, work can be calculated using the equation W = F * d * cos(theta), where F is the applied force, d is the displacement, and theta is the angle between the force and displacement vectors.
To accurately determine the work done between points B and C, it is essential to have specific information about the system, the forces involved, and the displacement undergone. Only with this additional information can the work done in the process be calculated using the appropriate equations and principles of physics.
Learn more about thermodynamic here:
https://brainly.com/question/32217565
#SPJ11
A highway curve with radius 900.0 ft is to be banked so that a car traveling 55.0 mph will not skid sideways even in the absence of friction. (a) Make a free-body diagram of this car. (b) At what angle should the curve be banked?
Therefore, the angle at which the curve should be banked is 8.54°.
a) Free-body diagram of the carThe free-body diagram of the car traveling on a banked curve is shown in the figure below:b) The angle at which the curve must be bankedFirst, let's derive an expression for the banking angle of the curve that a car traveling at 55.0 mph will not skid sideways even in the absence of friction.The horizontal and vertical forces that act on the car are equal to each other, according to the free-body diagram of the car. A reaction force acts on the car in the vertical direction that opposes the car's weight. There is no force acting on the car in the horizontal direction. The gravitational force and the normal reaction force act on the car at angles θ and 90o - θ, respectively. Since the vertical force on the car is equal to the centripetal force that acts on the car, it follows that the following equation can be used to determine the angle θ at which the curve must be banked: {mg sin θ = m v^2 /r};θ = arctan (v^2 / gr)θ = arctan [(55 mph)^2/(32.2 ft/s^2)(900 ft)]θ = arctan (0.148)θ = 8.54o. Therefore, the angle at which the curve should be banked is 8.54°.
To know more about highway curve visit:
https://brainly.com/question/31492871
#SPJ11
Two identical stones are dropped from a tall building, one after the other. Assume air resistance is negligible. While both stones are falling, what will happen to the vertical distance between them? a. It will increase. b. It will decrease. c. It will remain the same. d. It will first increase and then remain constant.
The vertical distance between two identical stones dropped from a tall building will remain the same as they fall.
When two identical stones are dropped from a tall building, neglecting air resistance, both stones will experience the same acceleration due to gravity. This means that they will fall at the same rate and maintain the same vertical distance between them throughout their descent.
Gravity acts equally on both stones, causing them to accelerate downward at approximately 9.8 meters per second squared (m/s²). Since both stones experience the same acceleration, their velocities will increase at the same rate. As a result, the vertical distance between the two stones will not change as they fall.
It's important to note that this scenario assumes ideal conditions, such as no air resistance and no external forces acting on the stones. In reality, factors such as air resistance or variations in initial conditions could cause slight differences in the fall of the stones, leading to a change in the vertical distance between them. However, under the given assumption of negligible air resistance, the vertical distance between the stones will remain the same.
Learn more about free fall:
https://brainly.com/question/13796105
#SPJ11
One long wire lies along an x axis and carries a current of 46 Ain the positive x direction A second long wire is perpendicular to the xy plane, passes through the point (0,6.4 m, 0), and carries a current of 45 A in the positive z direction. What is the magnitude of the resulting magnetic field at the point (0.11 m.)? Number ___________ Units ______________
The magnitude of the resulting magnetic field at the point (0.11 m) is 6.92 × 10⁻⁶ T.
The problem involves calculating the magnitude of the resulting magnetic field at a point (0.11 m). To do this, find the magnetic field caused by each wire and then add them together.
The formula for calculating the magnetic field caused by a wire is:
B = (µ₀ / 4π) * (2I / d)
Where:
B is the magnetic field,
I is the current,
d is the distance between the wire and the point where we want to calculate the magnetic field,
µ₀ is the permeability of free space, which is equal to 4π × 10⁻⁷ Tm/A.
Let's calculate the magnetic field caused by each wire:
For the first wire:
B₁ = (µ₀ / 4π) * (2 * 46 A / 0.11 m)
B₁ = 6.41 × 10⁻⁶ T
For the second wire:
B₂ = (µ₀ / 4π) * (2 * 45 A / 6.4 m)
B₂ = 2.63 × 10⁻⁶ T
The direction of B₂ is along the positive y-axis.
Now, calculate the total magnetic field by using the Pythagorean theorem:
B = √(B₁² + B₂²)
B = √((6.41 × 10⁻⁶)² + (2.63 × 10⁻⁶)²)
B = 6.92 × 10⁻⁶ T
Therefore, the magnitude of the resulting magnetic field at the point (0.11 m) is 6.92 × 10⁻⁶ T.
Learn more about magnetic field: https://brainly.com/question/7802337
#SPJ11
Two trains are traveling toward each other at 30.9 m/s relative to the ground. One train is blowing a whistle at 510 Hz. (Give your answers to at least three significant figures.) (a) What frequency will be heard on the other train in still air? Hz (b) What frequency will be heard on the other train if the wind is blowing at 30.9 m/s toward the whistle and away from the listener? Hz (c) What frequency will be heard if the wind direction is reversed? Hz
(a) The frequency heard on the other train in still air will be 510 Hz.
(b) The frequency heard on the other train, with the wind blowing toward the whistle and away from the listener, will be higher than 510 Hz.
(c) The frequency heard on the other train, with the wind direction reversed, will be lower than 510 Hz.
(a) When two trains approach each other, the frequency heard on the other train in still air is the same as the emitted frequency, which is 510 Hz in this case. This is because the speed of sound is the same in both directions relative to the ground.
(b) When the wind is blowing at 30.9 m/s toward the whistle and away from the listener, the effective speed of sound is increased. This is due to the additive effect of the wind speed to the speed of sound. As a result, the frequency heard on the other train will be higher than the emitted frequency of 510 Hz.
(c) Conversely, when the wind direction is reversed, the effective speed of sound is reduced. The wind speed is subtracted from the speed of sound, leading to a lower effective speed of sound. Therefore, the frequency heard on the other train will be lower than 510 Hz.
These changes in frequency, known as the Doppler effect, occur due to the relative motion between the source (train) and the observer (other train) as well as the medium through which the sound waves travel (air).
Learn more about frequency here ;
https://brainly.com/question/31938473
#SPJ11
3. With suitable sketch, explain the measuring instrument used
for measuring the Gauge Pressure
Gauge pressure is the pressure measured relative to atmospheric pressure. A commonly used instrument for measuring gauge pressure is the pressure gauge.
A pressure gauge typically consists of a circular dial with a pointer, a pressure sensing element, and a scale. The sensing element, which is usually a diaphragm or a Bourdon tube, is connected to the system or container whose pressure is being measured.
The pressure gauge is usually connected to the system or container through an inlet port. When the pressure in the system or container changes, it exerts a force on the sensing element of the pressure gauge. This force causes the sensing element to deform, which in turn moves the pointer on the dial. The position of the pointer on the pressure scale indicates the gauge pressure.
The pressure scale on the dial is calibrated in units such as psi (pounds per square inch), bar, or kPa (kilopascals), depending on the application and region. The scale allows the user to directly read the gauge pressure value.
It's important to note that the pressure gauge measures the difference between the pressure being measured and the atmospheric pressure. If the system or container is under vacuum (pressure lower than atmospheric pressure), the gauge will indicate negative values.
Pressure gauges are widely used in various industries and applications where monitoring and control of pressure is essential, such as in industrial processes, HVAC systems, pneumatic systems, and hydraulic systems.
Learn more about hydraulic pressure here:
brainly.com/question/857286
#SPJ11
Fiber optics are an important part of our modern internet. In these fibers, two different glasses are used to confine the light by total internal reflection at the critical angle for the interface between the core (n core
=1.519) and the cladding (n cladding
=1.429). A 50% Part (a) Numerically, what is the largest angle (in degrees) a ray will make with respect to the interface internal reflection? θ max
= Hints: deduction per hint. Hints remaining: 2
deduction per feedback. (4 50% Part (b) Suppose you wanted the largest angle at which total internal reflection occurred to be θ max
=5 (6\%) Problem 6: Suppose a 200-mm focal length telephoto lens is being used to photograph mountains 9.5 km away. ( 50% Part (a) What is image distance, in meters, for this lens? d i
= \begin{tabular}{llll} \hline Hints: deduction per hint. Hints remaining: 1 & Feedback: \end{tabular}
This makes the critical angle 5 degrees. To prove this, we use the same formula:sinθc = n2/n1sin(5) = 1.054/1.519θc = 5 degrees
Fiber optics are an important part of our modern internet. In these fibers, two different glasses are used to confine the light by total internal reflection at the critical angle for the interface between the core (ncore=1.519) and the cladding (ncladding=1.429).A 50%Part
(a) Numerically, what is the largest angle (in degrees) a ray will make with respect to the interface internal reflection? θmax=In order to determine the angle that a ray will make with respect to the interface internal reflection, we use Snell's Law: n1sinθ1 = n2sinθ2
where:n1 is the refractive index of the medium the ray is coming fromθ1 is the angle of incidence measured from the normaln2 is the refractive index of the medium the ray is enteringθ2 is the angle of refraction measured from the normalWhen light travels from a medium of a higher refractive index to one of a lower refractive index (i.e. from the core to the cladding),
the angle of refraction is larger than the angle of incidence; that is, the ray is refracted away from the normal. At the critical angle, however, the angle of refraction is 90 degrees. Thus, sinθ2 = 1. Setting sinθ1 = n2/n1, we get the critical angle formula:sinθc = n2/n1θc = sin^(-1)(n2/n1)
The maximum angle a ray will make with respect to the interface internal reflection will be the complement of the critical angle:θmax = 90 - θc = 90 - sin^(-1)(n2/n1) = 90 - sin^(-1)(1.429/1.519) = 42.45 degrees50%Part (b) Suppose you wanted the largest angle at which total internal reflection occurred to be θmax=5°. You could achieve this by decreasing the refractive index of the cladding to ncladding = 1.054.
This makes the critical angle 5 degrees. To prove this, we use the same formula:sinθc = n2/n1sin(5) = 1.054/1.519θc = 5 degrees
to know more about critical
https://brainly.com/question/24281057
#SPJ11
Taking into account the recoil (kinetic energy) of the daughter nucleus, calculate the kinetic energy K, of the alpha particle i the following decay of a 238U nucleus at rest. 238U - 234Th + a K = Mc Each fusion reaction of deuterium (H) and tritium (H) releases about 20.0 MeV. The molar mass of tritium is approximately 3.02% kg What mass m of tritium is needed to create 1015 5 of energy the same as that released by exploding 250,000 tons of TNT? Assume that an endless supply of deuterium is available. You take a course in archaeology that includes field work. An ancient wooden totem pole is excavated from your archacological dig. The beta decay rate is measured at 610 decays/min. years If a sample from the totem pole contains 235 g of carbon and the ratio of carbon-14 to carbon-12 in living trees is 1.35 x 10-12, what is the age 1 of the pole in years? The molar mass of 'C is 18.035 g/mol. The half-life of "Cis 5730 y An old wooden bowl unearthed in an archeological dig is found to have one-third of the amount of carbon14 present in a simi sample of fresh wood. The half-life of carbon-14 atom is 5730 years Determine the age 7 of the bowl in years 11463 43 year
The fraction of carbon-14 in the old bowl is given as: f = (1/3)N/N0= 1/3 (1/2)t/T1/2= 2-t/5730. Using the logarithmic function to solve for t, t = 11463 years.
In the given radioactive decay of a 238U nucleus, 238U - 234Th + αThe recoil kinetic energy of the daughter nucleus has to be taken into account to calculate the kinetic energy K of the alpha particle.238U (mass = 238) decays into 234 Th (mass = 234) and an alpha particle (mass = 4).
The total mass of the products is 238 u. Therefore,238 = 234 + 4K = (238 - 234) × (931.5 MeV/u)K = 3726 MeVIn the fusion of deuterium and tritium, each fusion reaction releases about 20.0 MeV.
Therefore, mass energy of 1015.5 eV = 1.6 × 10-19 J= 1.6 × 10-19 × 1015.5 J= 1.6256 × 10-4 J
The number of fusion reactions required to produce this energy is given asQ = 1.6256 × 10-4 J/20 MeV= 0.8128 × 1011
Number of moles of tritium required ism/MT = 0.8128 × 1011molTherefore, the mass of tritium required ism = MT × 0.8128 × 1011= 0.0302 × 0.8128 × 1011 kg= 2.45 × 1010 kg
The ancient wooden totem pole is excavated from the archaeological dig with a beta decay rate of 610 decays per minute per gram of carbon.
The ratio of carbon-14 to carbon-12 in living trees is 1.35 × 10-12. The age of the pole can be determined as: N(t)/N0 = e-λt
where, λ = 0.693/T1/2= 0.693/5730 yLet t be the age of the pole. Therefore, N(t)/N0 = 235 × 610 × e-0.693t/1.35 × 10-12
Solving for t, t = 7.51 × 103 years
The old wooden bowl has one-third of the amount of carbon-14 present in a similar sample of fresh wood.
Therefore, the fraction of carbon-14 in the old bowl is given as: f = (1/3)N/N0= 1/3 (1/2)t/T1/2= 2-t/5730
Using the logarithmic function to solve for t, t = 11463 years.
Learn more about kinetic energy here:
https://brainly.com/question/999862
#SPJ11
Build a circuit that has an adjustable power supply that adjusts the output voltage from 0 volts to 15 volts, and also has a fixed 8 volt power output. And also the supply will power a circuit containing a transistor or op amp
It is also necessary to make a description of the operation of the circuit
A circuit that can provide an adjustable power supply that can adjust the output voltage from 0 volts to 15 volts and also provide a fixed 8 volt power output, as well as power a circuit containing a transistor or op amp can be built using the following components and operation steps:
Components needed:
One transformer
One bridge rectifier
One 4700 uF capacitor
Two 1000 uF capacitors
One 15k potentiometer
One 12V Zener diode
One NPN transistor
One 10k resistor
Two 1k resistors
Operation description:
1. Begin by connecting the transformer's primary winding to the mains and its secondary winding to the rectifier circuit. The transformer should have a 12-0-12 volts, 1A secondary winding.
2. The bridge rectifier is connected to the secondary winding, which is composed of four 1N4007 diodes, with two of them mounted in one direction, while the other two are mounted in the opposite direction.
3. A 4700 uF capacitor is connected across the bridge rectifier's output to remove the ripple component of the rectified signal.
4. The 12V Zener diode is connected in parallel with the two 1000 uF capacitors, which are connected in series, with one side of each capacitor connected to one end of the potentiometer. The other ends of both capacitors are joined together and connected to the 0V terminal.
5. The potentiometer's center wiper is linked to the output, while one end is linked to the input.
6. A 10k resistor is connected between the input and the base of the transistor, with the collector of the transistor connected to the output and the emitter linked to the 0V terminal.
7. Finally, two 1k resistors are used to bias the op amp circuit, with one resistor connected between the input and the op amp's positive input and the other resistor connected between the negative input and the 0V terminal.
In this configuration, the output voltage can be changed by moving the potentiometer's wiper to any point between the input and 15 volts. The 8 volt output is fixed and is located between the input and the potentiometer's 0 volt output. The op amp circuit is also biased by two 1k resistors.
Thus the required connection is set up.
learn more about power supply here:
https://brainly.com/question/32460638
#SPJ11