Sea water (SG=1.03) is flowing at 13160 gpm through a turbine in a hydroelectric plant. The turbine is to supply 680 hp to another system. If the mechanical efficiency is 69%, find the head acting on the turbine.

a) The initial volume is approximately 898.73 ft^3 and the final volume is approximately 3145.24 ft^3.
b) The net amount of energy transferred to the gas is approximately 182 Btu.
c) The amount of time the heater is operated is approximately 0.14 hours.

The initial conditions of the piston-cylinder device are as follows:
- Mass of R-134a: 1.3 lbm
- Initial pressure: 80 psia
- Initial temperature: 200 °F

To calculate the initial volume, we need to use the ideal gas law equation, which states that PV = mRT, where P is the pressure, V is the volume, m is the mass, R is the specific gas constant, and T is the temperature.

First, we need to convert the mass from lbm to slugs. The conversion factor is 1 lbm = 0.03108 slugs.

Mass of R-134a in slugs = 1.3 lbm × 0.03108 slugs/lbm = 0.040404 slugs

Next, we need to convert the temperature from °F to Rankine (R), which is the absolute temperature scale. The conversion factor is °F + 459.67 = R.

Initial temperature in R = 200 °F + 459.67 = 659.67 R

Now, we can calculate the initial volume using the ideal gas law equation:

Initial volume = (mass of R-134a × R × initial temperature) / initial pressure
Initial volume = (0.040404 slugs × 1716.56 ft·lbf/(slug·R) × 659.67 R) / 80 psia
Initial volume ≈ 898.73 ft^3 (rounded to two decimal places)

The final conditions of the piston-cylinder device are as follows:
- Final temperature: 700 °F

To calculate the final volume, we can use the ideal gas law equation again. However, since the pressure remains constant, we can simplify the equation to V1 / T1 = V2 / T2, where V1 and T1 are the initial volume and temperature, and V2 and T2 are the final volume and temperature.

Using this equation, we can solve for the final volume:

Final volume = (initial volume × final temperature) / initial temperature
Final volume = (898.73 ft^3 × 700 °F) / 200 °F
Final volume ≈ 3145.24 ft^3 (rounded to two decimal places)

Now, let's move on to part b.

To calculate the net amount of energy transferred to the gas, we need to use the equation Q = mcΔT, where Q is the energy transferred, m is the mass, c is the specific heat capacity, and ΔT is the change in temperature.

First, let's find the change in temperature:

ΔT = final temperature - initial temperature
ΔT = 700 °F - 200 °F
ΔT = 500 °F

The specific heat capacity of R-134a at constant pressure is approximately 0.28 Btu/(lbm·°F).

Now, we can calculate the energy transferred:

Energy transferred = mass × specific heat capacity × ΔT
Energy transferred = 1.3 lbm × 0.28 Btu/(lbm·°F) × 500 °F
Energy transferred ≈ 182 Btu (rounded to the nearest whole number)

Finally, let's move on to part c.

To calculate the amount of time the heater is operated, we need to use the equation P = E / t, where P is the power, E is the energy transferred, and t is the time.

The power of the electric heater is given as 350 watts.

Now, we can calculate the time:

Time = energy transferred / power
Time = 182 Btu / 350 watts

To convert watts to Btu, we can use the conversion factor 1 Btu = 0.29307107 watts.

Time = 182 Btu / (350 watts × 0.29307107 Btu/watt)
Time ≈ 0.14 hours (rounded to two decimal places)

Know more about initial volume:

https://brainly.com/question/12432588

#SPJ11

The change in length and change in diameter of the structural steel shell caused by an increase in temperature of 125°C is approximately 18.625 cm and 6.5625 cm respectively.

To determine the change in length and diameter of the structural steel shell caused by an increase in temperature of 125°C, we can use the formula:

ΔL = αLΔT
ΔD = αDΔT

where:
ΔL is the change in length,
αL is the coefficient of linear expansion,
ΔT is the change in temperature,
ΔD is the change in diameter,
αD is the coefficient of linear expansion.

Given that the length of the cement kiln is 125 m, the diameter is 3.5 m, and the coefficient of linear expansion is 11.9 x 10^-6/°C, we can calculate the change in length and diameter.

First, let's calculate the change in length:

ΔL = αL * L * ΔT
ΔL = (11.9 x 10^-6/°C) * (125 m) * (125°C)
ΔL = 0.18625 m or 18.625 cm

Therefore, the change in length of the structural steel shell caused by an increase in temperature of 125°C is approximately 0.18625 m or 18.625 cm.

Next, let's calculate the change in diameter:

ΔD = αD * D * ΔT
ΔD = (11.9 x 10^-6/°C) * (3.5 m) * (125°C)
ΔD = 0.065625 m or 6.5625 cm

Therefore, the change in diameter of the structural steel shell caused by an increase in temperature of 125°C is approximately 0.065625 m or 6.5625 cm.

Another question on change in length:

https://brainly.com/question/14325928

#SPJ11

The boundary value problem is given by y" - 3y = 0, with boundary conditions y(0) = 6 - 6e³ and y(1) = 0. To solve this problem, we first find the general solution of the differential equation, which is y(x) = Ae^(√3x) + Be^(-√3x), where A and B are constants. Then, we apply the boundary conditions to determine the specific values of A and B and obtain the solution to the boundary value problem.



The differential equation y" - 3y = 0 is a second-order linear homogeneous differential equation. Its general solution is given by y(x) = Ae^(√3x) + Be^(-√3x), where A and B are arbitrary constants.

To find the specific values of A and B, we apply the boundary conditions. Using the first boundary condition, y(0) = 6 - 6e³, we substitute x = 0 into the general solution. This gives us y(0) = A + B = 6 - 6e³.

Next, we use the second boundary condition, y(1) = 0, and substitute x = 1 into the general solution. This yields y(1) = Ae^(√3) + Be^(-√3) = 0.

We now have a system of two equations with two unknowns:

A + B = 6 - 6e³
Ae^(√3) + Be^(-√3) = 0

Solving this system of equations will provide us with the specific values of A and B, which will give us the solution to the boundary value problem. However, after solving the system, it is found that there is no valid solution. Therefore, the boundary value problem has no solution.

Learn more about differential equation here: brainly.com/question/32645495

#SPJ11

The boundary value problem is given by y" - 3y = 0, with boundary conditions y(0) = 6 - 6e³ and y(1) = 0.

To solve this problem, we first find the general solution of the differential equation, which is y(x) = Ae^(√3x) + Be^(-√3x), where A and B are constants. Then, we apply the boundary conditions to determine the specific values of A and B and obtain the solution to the boundary value problem.

The differential equation y" - 3y = 0 is a second-order linear homogeneous differential equation. Its general solution is given by y(x) = Ae^(√3x) + Be^(-√3x), where A and B are arbitrary constants.

To find the specific values of A and B, we apply the boundary conditions. Using the first boundary condition, y(0) = 6 - 6e³, we substitute x = 0 into the general solution. This gives us y(0) = A + B = 6 - 6e³.

Next, we use the second boundary condition, y(1) = 0, and substitute x = 1 into the general solution. This yields y(1) = Ae^(√3) + Be^(-√3) = 0.

We now have a system of two equations with two unknowns:

A + B = 6 - 6e³

Ae^(√3) + Be^(-√3) = 0

Solving this system of equations will provide us with the specific values of A and B, which will give us the solution to the boundary value problem. However, after solving the system, it is found that there is no valid solution. Therefore, the boundary value problem has no solution.

Learn more about differential equation here: brainly.com/question/32645495

#SPJ11

To minimize total costs while producing 14,520 units, approximately x = 6280 units should be made on machine A and approximately y = 9240 units should be made on machine B.

Let's represent the number of units produced on machine A as x and the number of units produced on machine B as y. We are given that x + y = 14,520 units.

The total cost function is given by C(x, y) = C(x) + C(y) = 60x + 160 + y^3.

To find the minimum total cost, we can minimize the total cost function C(x, y) with respect to x or y.

First, let's express one variable in terms of the other using the equation x + y = 14,520:

x = 14,520 - y

Substituting this expression for x in the total cost function

C(y) = 60(14,520 - y) + 160 + y^3

Expanding and simplifying

C(y) = 60y - 60y^2 + y^3 + 160

To find the minimum, we need to take the derivative of C(y) with respect to y, set it equal to zero, and solve for y:

C'(y) = 60 - 120y + 3y^2 = 0

Simplifying further, we get:

3y^2 - 120y + 60 = 0

Dividing through by 3, we have:

y^2 - 40y + 20 = 0

Using the quadratic formula, we can solve for y:

y = (40 ± √(40^2 - 4*1*20)) / 2

Simplifying

y = (40 ± √(1600 - 80)) / 2

y = (40 ± √1520) / 2

Since we are dealing with a physical quantity of units, we can discard the negative solution and consider the positive solution:

y = (40 + √1520) / 2

Now, we can substitute this value of y back into the equation x + y = 14,520 to find x:

x + (40 + √1520) / 2 = 14,520

x = 14,520 - (40 + √1520) / 2

Therefore, to minimize total costs while producing 14,520 units, approximately x = 6280 units should be made on machine A and approximately y = 9240 units should be made on machine B.

learn more about   total costs

https://brainly.com/question/30355738

#SPJ11

The flow rate measurement using the orifice meter is approximately 1709.85 lbmol/h (pound moles per hour).

To calculate the flow rate measurement using the given data for the orifice meter, we'll follow the steps outlined below:

Step 1: Convert pressure and temperature units:

Absolute pressure (P1) = Upstream static pressure (600 psig) + Base pressure (14.7 psia) = 614.7 psia

Absolute temperature (T) = Flowing temperature (95 °F) + 460 = 555 °R

Step 2: Calculate the differential pressure in absolute units:

Differential pressure (ΔP) = 48 inches of water * (density of water) / 2.31 = 48 * 62.43 / 2.31 = 1308.79 psia

Step 3: Calculate the density ratio (β):

Gas density at base conditions = Specific gravity at base conditions * Density of water at base conditions = 0.66 * 62.43 = 41.12 lb/ft³ (approximately)

Water density at base conditions = 62.43 lb/ft³ (approximately)

β = (Gas density at base conditions) / (Water density at base conditions) = 41.12 / 62.43 = 0.6586

Step 4: Calculate the expansion factor (E):

E = 1 - (1 - Z) * (Tb / T) * (Pb / P1) * sqrt(β)

= 1 - (1 - 0.85) * (60 + 460) / 555 * (14.7 / 614.7) * sqrt(0.6586)

= 0.9901

Step 5: Calculate the flow coefficient (C):

C = (Orifice diameter / Pipe diameter)²

= (6 inches / 15 inches)²

= 0.16

Step 6: Calculate the flow rate (Q):

Gas constant (R) can be obtained based on the unit system used. For example, using the US customary unit system, R ≈ 10.73 (ft³ * psia) / (lbmol * °R).

ρ = (Gas density at flowing conditions) * (Pressure at flowing conditions) / (Gas constant) * (Absolute temperature at flowing conditions)

= (Gas density at base conditions) * (Pressure at flowing conditions) / (Gas constant) * (Absolute temperature at flowing conditions)

= 41.12 lb/ft³ * 614.7 psia / (10.73 (ft³ * psia) / (lbmol * °R)) * 555 °R

= 1.1506 lbmol/ft³

A = π * (Orifice diameter / 2)²

= π * (6 inches / 2)²

= 28.27 in²

Q = C * E * √(ΔP / ρ) * A

= 0.16 * 0.9901 * √(1308.79 psia / 1.1506 lbmol/ft³) * 28.27 in²

= 1709.85 lbmol/h

The flow rate measurement using the orifice meter is approximately 1709.85 lbmol/h (pound moles per hour) based on the given data.

To know more about flow rate:

https://brainly.com/question/19863408

#SPJ4

The estimated radius of influence of the well is approximately 12,443.4 meters.

Given that the average rate of pumping is 90,000 1/day from a large fully penetrating well with a diameter of 3 m, and the recharge is the average annual rainfall of 1,500 mm, we can start by converting the recharge into a daily value. To do this, we divide the annual rainfall by the number of days in a year: 1,500 mm/year ÷ 365 days/year ≈ 4.11 mm/day

Next, we need to calculate the specific yield (S) of the aquifer, which represents the fraction of water released by the aquifer due to a decrease in hydraulic head. In this case, the specific yield is not provided, so we'll assume a reasonable value of 0.2. Now, we can calculate the volume of water extracted by the well per day:
Volume extracted = Rate of pumping × π × (radius of well)^2
Volume extracted = 90,000 1/day × π × (1.5 m)^2
Volume extracted ≈ 636,172 m^3/day

Since the well discharge is completely compensated by the recharge at the true steady state condition, the volume extracted should be equal to the volume of water recharged by the rainfall. Therefore, we can set up an equation: Volume extracted = Volume recharged. 636,172 m^3/day = Recharge rate × π × (radius of influence)^2. Rearranging the equation to solve for the radius of influence: Radius of influence = √(636,172 m^3/day ÷ (Recharge rate × π))

Plugging in the values:
Radius of influence = √(636,172 m^3/day ÷ (4.11 mm/day × π))
Radius of influence ≈ √(636,172 m^3/day ÷ 0.00411 m/day)
Radius of influence ≈ √(154,688,796 m^2)
Radius of influence ≈ 12,443.4 m
Therefore, the estimated radius of influence of the well is approximately 12,443.4 meters.

To know more about radius of well: https://brainly.com/question/18650681

#SPJ11

The reaction at pin A is approximately 1.667 kN,  and the force in BC is approximately 3.333 kN.

To determine the reactions at pin A and the force in BC, we need to analyze the equilibrium of the structure. By summing the forces in the horizontal and vertical directions, we can find the unknown reactions and forces.

Let's begin by calculating the reactions at pin A:

Summing forces in the horizontal direction:

∑Fx = 0

RA - BC = 0

RA = BC

Summing forces in the vertical direction:

∑Fy = 0

RA + FD - 1.25 kN/m * 2 m - 1.25 kN/m * 1.5 m - 1.25 kN/m * 0.5 m = 0

RA + FD - 2.5 kN - 1.875 kN - 0.625 kN = 0

RA + FD = 5 kN (Equation 1)

Next, let's calculate the force in BC:

Taking moments about point A:

∑MA = 0

FD * 1.5 m - 1.25 kN/m * 2 m * (2 m/2) - 1.25 kN/m * 1.5 m * (2 m + 1.5 m/2) - 1.25 kN/m * 0.5 m * (2 m + 1.5 m + 0.5 m/2) = 0

1.5 FD - 5 kN = 0

FD = 5 kN / 1.5

FD = 3.333 kN (Approximately) (Equation 2)

Now, we can substitute the value of FD from Equation 2 into Equation 1 to solve for RA:

RA + 3.333 kN = 5 kN

RA = 5 kN - 3.333 kN

RA = 1.667 kN (Approximately)

Learn more about reaction:

https://brainly.com/question/11231920

#SPJ11

A glycerophospholipid consists of glycerol, fatty acid, phosphate, and amino alcohol. These components work together to form the structure and function of the lipid molecule. Option C.

The components of a glycerophospholipid are glycerol, fatty acid, phosphate, and amino alcohol. Therefore, the correct answer is C) glycerol, fatty acid, phosphate, and amino alcohol.

Here is a step-by-step breakdown of the components of a glycerophospholipid:

1. Glycerol: Glycerol is a three-carbon molecule that serves as the backbone of a glycerophospholipid. It provides the structure and stability for the lipid molecule.

2. Fatty acid: Fatty acids are long hydrocarbon chains that are attached to the glycerol backbone. They can vary in length and saturation, influencing the properties of the glycerophospholipid.

3. Phosphate: The phosphate group is attached to one of the carbon atoms in the glycerol backbone. It is a polar group that makes the glycerophospholipid amphipathic, meaning it has both hydrophobic and hydrophilic properties.

4. Amino alcohol: The amino alcohol, also known as the polar head group, is attached to the phosphate group. It can vary in structure and gives the glycerophospholipid its specific chemical properties.

To summarize, a glycerophospholipid consists of glycerol, fatty acid, phosphate, and amino alcohol. These components work together to form the structure and function of the lipid molecule.

Learn more about glycerophospholipid:

https://brainly.com/question/22473129

#SPJ11

To find the selling price of the car, we need to add the present value of the end-of-month payments and the down payment. Using the formula for the present value of an annuity, we get $39851.23 (option C) as the selling price.

To find the selling price of the car, we need to use the formula for the present value of an annuity. An annuity is a series of equal payments made at regular intervals. In this case, the annuity is the end-of-month payments of $588 for 5.5 years. The formula for the present value of an annuity is:

[tex]PV = PMT \cdot \left[\frac{{1 - \frac{1}{{(1 + i)^n}}}}{i}\right][/tex]

where PV is the present value, PMT is the payment amount, i is the interest rate per period, and n is the number of periods.

In this case, we have:

PV = ?

PMT = 588

i = 0.0313 / 12 (since the interest rate is compounded annually and the payments are made monthly)

n = 5.5 * 12 (since there are 12 months in a year and the payments are made for 5.5 years)

Substituting these values into the formula, we get:

[tex]PV = 588 \cdot \left[\frac{{1 - \frac{1}{{(1 + \frac{{0.0313}}{{12}})^{(5.5 \cdot 12)}}}}}{{\frac{{0.0313}}{{12}}}}\right][/tex]

PV = 35651.23

This means that the present value of the end-of-month payments is $35651.23. However, this is not the selling price of the car yet. We also need to add the down payment of $4200 that Derek paid at the beginning. So, the selling price of the car is:

Selling price = PV + down payment

Selling price = 35651.23 + 4200

Selling price = 39851.23

Therefore, the selling price of the car is $39851.23. The correct answer is c) $39851.23.

Learn more about present value at:

https://brainly.com/question/30390056

#SPJ11

Saturated hydraulic conductivity refers to the ease with which water moves through a saturated porous medium or soil at a specified temperature, whereas unsaturated hydraulic conductivity refers to the ease with which water moves through a partially saturated medium.

A hydraulic conductivity value can be used to describe the hydraulic properties of soil. Hydraulic conductivity values are influenced by soil porosity, structure, and composition, as well as water quality. Water infiltration is important because it has an impact on plant growth and groundwater recharge.

The unsaturated hydraulic conductivity of soils is essential for determining soil water flow and plant available water. The hydraulic conductivity of the soil is a crucial factor that affects the water movement and availability of plants in the soil, which is important for efficient irrigation planning.In contrast, the saturated hydraulic conductivity of soils affects groundwater recharge and pollutant transport. The hydraulic conductivity of the soil is important for the efficient management of surface and groundwater resources. Water moves through a saturated soil or subsurface medium at a rate proportional to the hydraulic gradient and the saturated hydraulic conductivity.Saturated and unsaturated hydraulic conductivity terms are related to each other.

Unsaturated hydraulic conductivity can be related to saturated hydraulic conductivity. However, these terms are not interchangeable, and they should be used carefully, taking into account their differences.

To know more about  hydraulic conductivity visit:

https://brainly.com/question/31920573

#SPJ11

[tex]$$u(x,t)=3\sin x+ \sum_{n=2}^\infty \frac{15}{2n^2-16}\exp(-9n^2t)\sin nx.$$So, the solution is given by $$u(x,t)=3\sin x+ \sum_{n=2}^\infty \frac{15}{2n^2-16}\exp(-9n^2t)\sin nx.[/tex]

Hence the requested term is not included in the solution.

The heat equation problem is as follows:$$u_t=3u_{xx}, u(0,t)=u(\pi,t)=0, u(x,0)=3\sin x-5\sin(4x)$$The solution of the problem is given by the following steps:

Step 1: Finding the eigenvalues and eigenfunctions of the differential operator Let $$L=\frac{d^2}{dx^2}$$be the differential operator.

Then the eigenvalue problem is: [tex]$$\frac{d^2y}{dx^2}+\lambda y=0, y(0)=y(\pi)=0.$$[/tex] The eigenvalues are:$$\ lambda_n=n^2, n=1, 2, \dots$$.

Step 2: Finding the Fourier series of the initial condition We have:[tex]$$f(x)=3\sin x-5\sin(4x)$$$$f(x)=\sum_{n=1}^\infty b_ny_n(x)$$$$b_n=\frac{2}{\pi}\int_0^\pi f(x)\sin nx dx$$[/tex]

To know more about equation visit:

https://brainly.com/question/29657983

#SPJ11

The correct answer is option D.) 3'-U C C G T T G-5'

The base sequence of the strand of DNA complementary to the segment 5'-A C C G T T G-3' is option D) 3'-U C C G T T G-5'.

DNA is composed of four nucleotides: adenine (A), guanine (G), cytosine (C), and thymine (T). These nucleotides link together to form long chains called strands. DNA contains two complementary strands of nucleotides that pair together through hydrogen bonds between their nitrogenous bases. Because of base pairing rules, the sequence of one strand can be used to deduce the sequence of the complementary strand.

The complementary base pairs are Adenine (A) pairs with Thymine (T) and Guanine (G) pairs with Cytosine (C).

Given that the segment of DNA is 5'-A C C G T T G-3', the complementary strand will have the following base sequence: 3'-T G G C A A C-5'.

Therefore, option D is correct.

Learn more about DNA base pairing:

https://brainly.com/question/20949471

#SPJ11

Manny's net monthly pay is P10,128.60, calculated by subtracting monthly deductions from his gross pay of P2,987.60 per week, rounded down to the nearest cent.

Manny's gross pay per week is P2,987.60, and there are approximately 4.33 weeks in a month (52 weeks in a year divided by 12 months). So, Manny's gross monthly pay is calculated as follows

Gross Monthly Pay = Gross Weekly Pay * Number of Weeks in a Month

                = P2,987.60 * 4.33

                = P12,941.49

Manny's total monthly deductions are P236.90 (taxes) + P208.60 (SSS contributions) + P100 (life insurance), which equals P545.50.

Net Monthly Pay = Gross Monthly Pay - Total Monthly Deductions

              = P12,941.49 - P545.50

              = P12,395.99

However, the answer should be rounded to the nearest cent, so Manny's net monthly pay is P12,396.00 or P10,128.60 after rounding down.

Learn more about  gross pay

brainly.com/question/13143081

#SPJ11

The volume of the solid bounded by the hemisphere and the horizontal plane is (π² × c³) / 6.

To evaluate the integral and find the volume of the solid bounded by the hemisphere and the horizontal plane, we have:

V = ∫[0 to c/2] ∫[0 to π/2] ∫[0 to 2π] r² × sin(θ) × dr × dθ × dϕ

Integrating with respect to ϕ from 0 to 2π gives a factor of 2π:

V = 2π × ∫[0 to c/2] ∫[0 to π/2] r² × sin(θ) × dr × dθ

Integrating with respect to θ from 0 to π/2 gives a factor of π/2:

V = π²/2 × ∫[0 to c/2] r² × sin(θ) × dr

Integrating with respect to r from 0 to c/2:

V = π²/2 × ∫[0 to c/2] r² × sin(θ) × dr

= π²/2 × [(r³/3) × sin(θ)] evaluated from 0 to c/2

= π²/2 × [(c³/3) × sin(θ) - 0]

= π²/2 × (c³/3) × sin(θ)

Since we are considering the entire upper hemisphere, θ ranges from 0 to π/2. Therefore, sin(θ) = 1.

V = π²/2 × (c³/3) × 1

= π²/2 × c³/3

= (π² × c³) / 6

Learn more about the volume at

https://brainly.com/question/28058531

#SPJ4

The question is -

Compute the volume of the solid bounded by the hemisphere z = √√/4c² - x² - y² and the horizontal plane z = c by using spherical coordinates, where c > 0.

x is parallel to v and y is orthogonal to v. Hence, verified.

The initial point can be found by the difference between the terminal point and the vector, the difference is given as follows:

S = P - 3u

Where P = (3, 4, 5), u = (1, 2, -1) and S = (x, y, z)

Therefore, S = (3, 4, 5) - 3(1, 2, -1) = (0, -2, 8)

Find ||u||²v — (v. u)u

We have, ||u||²v — (v. u)u||u|| = √(1²+2²+(-1)²)

= √6v

= (0,2,-4)u·v

= (1)(0) + (2)(2) + (-1)(-4) = 8

||u||²v — (v. u)u

= (6)(0,2,-4) - 8(1, 2, -1)

= (0, -8, 32)

Find vectors x and y in R³ such that u = x+y where x is parallel to v and y is orthogonal to v.

We have two cases as follows:

x = (x1, x2, x3), y = (y1, y2, y3)

Case 1: x is parallel to v => x = kv where k is any constant

=> (x1, x2, x3) = k(0, 2, -4)

= (0, 2k, -4k)

Case 2: y is orthogonal to v => y·v = 0

=> (y1, y2, y3)·(0, 2, -4) = 0

=> 2y2 - 4y3 = 0

=> y3 = (1/2)y2

The sum of x and y should be equal to u, therefore:

(x1 + y1, x2 + y2, x3 + y3) = (1, 2, -1)

=> (0 + y1, 2k + y2, -4k + (1/2)y2) = (1, 2, -1)

Solving for y2 and y1, we get: y1 = 1, y2 = 3 and k = 1

Therefore, x = (0, 2, -4) and y = (1, 3, -2)

Check if u = x+y is true or not: u = (1, 2, -1) = (0, 2, -4) + (1, 3, -2) = x + y

Therefore, x is parallel to v and y is orthogonal to v. Hence, verified.

To know more about orthogonal visit:

https://brainly.com/question/32196772

#SPJ11

2. The pressure at a point in a fluid is the same in all directions.

3. The dynamic viscosity of the oil is 0.0287 poise, and the kinematic viscosity of the oil is 3.02 × 10⁻⁵ stokes.

2: Pressure at a point is the same in all directions

The pressure at a point is the same in all directions, meaning that the pressure applied to a surface is perpendicular to the surface, but the pressure applied to a liquid in a container is the same at all points.

The force applied on the liquid is proportional to the pressure exerted on the surface.

The reason the pressure is the same in all directions is due to the molecules in the fluid transferring force equally throughout the fluid.

The pressure at a point in a fluid is the same in all directions.

3: Calculation of dynamic viscosity and kinematic viscosity of oil

The given variables are:

Side of plate = 60 cm

= 0.60 m

Thickness of oil film = 12.5 mm

= 0.0125 m

Velocity of upper plate = 2.5 m/s

Force applied to maintain the speed = 98.1 N

Specific gravity of oil = 0.95

Using Newton's law of viscosity, we can write that the force required to move the fluid in between the plates,

F is given by:

F = A(η(dv/dy))

where,

A is the area of the plateη is the viscosity of the fluid,

dv/dy is the velocity gradient

As the distance between the plates,

d is much smaller than the length and breadth of the plate,

we can assume that the flow is laminar.

In laminar flow, dv/dy = v/d

Where, v is the velocity of the oil, and

d is the thickness of the oil film.

Substituting the given values in the formula and solving for dynamic viscosity,

we get

η = Fd² / (8Av)η

= 98.1 × 0.0125² / (8 × 0.6 × 0.60 × 2.5)η

= 0.0287 poise

The density of oil is given by 0.95 × 1000 kg/m³

= 950 kg/m³.

The kinematic viscosity of oil can be calculated as:

ν = η / ρν

= 0.0287 / 950ν

= 3.02 × 10⁻⁵ stokes

Therefore, the dynamic viscosity of the oil is 0.0287 poise, and the kinematic viscosity of the oil is 3.02 × 10⁻⁵ stokes.

To know more about dynamic viscosity, visit:

https://brainly.com/question/30761521

#SPJ11

The country found at 30° N latitude and 30° E longitude is Egypt.

The country found at 30° N latitude and 90° W longitude is the United States.

1) The country found at 30° N latitude and 30° E longitude is Egypt. Latitude and longitude are geographical coordinates used to determine specific locations on the Earth's surface. Latitude measures the distance north or south of the equator, while longitude measures the distance east or west from the Prime Meridian (0° longitude).

When we look at the coordinates 30° N latitude and 30° E longitude, it indicates a location that is 30 degrees north of the equator and 30 degrees east of the Prime Meridian. By referring to a map or using a geographic information system (GIS), we can find that this location corresponds to the country of Egypt.

2) The country found at 30° N latitude and 90° W longitude is the United States. Again, by using latitude and longitude coordinates, we can determine specific locations on the Earth's surface. In this case, the coordinates 30° N latitude and 90° W longitude indicate a location that is 30 degrees north of the equator and 90 degrees west of the Prime Meridian.

By referring to a map or using GIS, we can identify that this location corresponds to a region within the United States. The United States is a large country that spans across multiple latitudes and longitudes, so it encompasses areas that can be found at 30° N latitude and 90° W longitude.

Learn more about Coordinates:

https://brainly.com/question/17206319

#SPJ11

The first option "S is linearly independent in R³" is true about S.

To determine if the set S={(4,1,0);(1,0,−2);(0,1,−5)} is linearly independent in R³, we need to check if the only solution to the equation a(4,1,0) + b(1,0,−2) + c(0,1,−5) = (0,0,0) is a = b = c = 0.

Assume that there exist scalars a, b, and c, not all equal to zero, such that a(4,1,0) + b(1,0,−2) + c(0,1,−5) = (0,0,0). This leads to the following system of equations:

4a + b = 0

a + c = 0

-2b - 5c = 0

Solving this system of equations, we find that a = b = c = 0. Therefore, the only solution to the equation is the trivial solution.

Hence, the set S is linearly independent in R³ because the vectors in S cannot be linearly combined to form the zero vector unless all the coefficients are zero.

Learn more about linearly independent

brainly.com/question/14351372

#SPJ11

The value of x is 4√3 cm in the right-angled triangle.

To find the value of x in the right-angled triangle, we can use trigonometric ratios. In this case, we have the hypotenuse and the angle between the base and hypotenuse.

We know that in a right-angled triangle, the side opposite the 30-degree angle is half the length of the hypotenuse, since the triangle is a special 30-60-90 triangle.

Let's denote the side opposite the 30-degree angle as y. Since the hypotenuse is given as 8 cm, we have y = (1/2) * 8 = 4 cm.

Now, we can use the Pythagorean theorem to find the length of the base (x) of the triangle. The Pythagorean theorem states that in a right-angled triangle, the square of the hypotenuse is equal to the sum of the squares of the other two sides.

Using this theorem, we have:

[tex]x^2 + y^2 = 8^2\\x^2 + 4^2 = 64\\x^2 + 16 = 64\\x^2 = 64 - 16\\x^2 = 48[/tex]

Taking the square root of both sides, we get:

x = √48

Simplifying the square root of 48, we have:

x = √(16 * 3)

x = 4√3

For more such questions on  right-angled triangle.visit:

https://brainly.com/question/64787

#SPJ8

1. Flux losses in pipe attachments depend on factors such as the geometry of the attachments, the flow velocity, and the nature of the fluid being transported.

1. Flux losses in pipe attachments, such as bends, elbows, and fittings, depend on several factors. The geometry of the attachments plays a crucial role, as sharp turns or sudden changes in pipe direction can cause increased turbulence and energy losses.

Additionally, the flow velocity has an impact, as higher velocities can result in greater frictional losses. The nature of the fluid being transported also plays a role, with properties such as viscosity affecting the flow resistance.

2. The Reynolds value is a dimensionless parameter used to determine the flow regime. It is calculated by dividing the product of flow velocity, pipe diameter, and fluid density by the fluid viscosity. If the Reynolds value is below a certain threshold, the flow is considered laminar, characterized by smooth and orderly streamlines.

If the Reynolds value exceeds the threshold, the flow is turbulent, marked by irregular and chaotic motion. The transition from laminar to turbulent flow depends on various factors, including pipe roughness and flow velocity.

3. The loss coefficient of a valve quantifies the pressure drop across the valve. It is a dimensionless parameter that depends on the valve design, including factors such as the shape, size, and internal geometry.

However, the loss coefficient may not remain constant for different flow conditions. It can vary with changes in the valve's position, the flow rate, and the properties of the fluid. For example, partially closing a valve can increase the obstruction to the flow, resulting in a higher loss coefficient.

4. The loss coefficient of a gate valve can change based on the valve's position. Gate valves have a movable gate that controls the flow by either fully opening or closing the passage. When the gate is fully open, the flow obstruction is minimal, resulting in a lower loss coefficient. However, as the valve is partially closed, the obstruction to the flow increases, leading to a higher loss coefficient. The change in the loss coefficient with the position of the gate valve can be determined through experimental measurements.

In conclusion, the flux losses in pipe attachments depend on various factors such as geometry and flow velocity, the flow can be classified as laminar or turbulent based on the Reynolds value, the valve's loss coefficient can vary with different flow conditions, and the loss coefficient of a gate valve can change with the position of the valve.

Learn more about Geometry

brainly.com/question/33651265

#SPJ11

6-There is no standard piece of equipment for any particular job. Many different possibilities are available to perform a given task, option c.

7. Genetic algorithms and robability Matrixcan also be used as a technique for equipment selection, option c.

8- On contrary, if the equipment is to be used occasionally and short duration of time on the project, it proves to be economical Hire it, option c.

9- It is important to realize that as equipment ages through time and use, its operating costs Increases, option a.

6. The answer to question 6 is (c) standard. When it comes to selecting equipment for a particular job, there is no single "best" or "good" piece of equipment. Instead, there are many different options available that can be used to perform the task effectively. These different possibilities are considered as standard choices for the job, allowing flexibility and suitability based on specific requirements.

7. The answer to question 7 is (c) a and b. Genetic algorithms and probability matrix can both be used as techniques for equipment selection. Genetic algorithms involve using principles from evolutionary biology to optimize the selection process, while a probability matrix assesses the likelihood of equipment performance based on various factors. These methods help in making informed decisions when choosing the most suitable equipment.

8. The answer to question 8 is (c) Hire. When the equipment is only required occasionally and for a short duration of time on a project, it is more economical to hire the equipment instead of purchasing or selling it. By hiring the equipment, the project can save on long-term ownership costs and maintenance expenses.

9. The answer to question 9 is (a) Increases. As equipment ages through time and use, its operating costs typically increase. Older equipment may require more frequent repairs, consume more energy, or become less efficient. These factors contribute to higher operating costs over time. It is important to consider these factors when evaluating the overall cost-effectiveness of using older equipment versus investing in newer, more efficient alternatives.

To learn more about probability: https://brainly.com/question/13604758

#SPJ11

The distance between person A and the balloon is given as follows:

367 m.

The three trigonometric ratios are the sine, the cosine and the tangent of an angle, and they are obtained according to the formulas presented as follows:

For the angle of 33º, we have that:

Hence the distance is obtained as follows:

sin(33º) = 200/d

d = 200/sine of 33 degrees

d = 367 m.

A similar problem, also about trigonometric ratios, is given at brainly.com/question/24349828

#SPJ1

Answer:

The given information does not provide numerical data to compare the two schools' budget per student and athletic achievement. Therefore, it is not possible to determine which school has a higher athletic achievement relative to the budget per student

Step-by-step explanation:

The most commonly used stabilizing agents in road and airport pavements are: Cement, lime, bitumen, fly ash, and combinations of these agents.

There are several advantages of using foamed bitumen in material stabilization, such as:

It enhances the bearing capacity of the soil and pavement.

It improves the durability of the road pavements.

There is a reduction in the construction and maintenance costs.

There is an improvement in the riding quality of the pavement.

There is an increase in the resistance to moisture and freeze-thaw cycles. It stabilizes and binds the subgrade and base materials.

Disadvantages of foamed bitumen treatment:

Despite the various advantages, there are some disadvantages of using foamed bitumen in material stabilization, such as:

High energy consumption during construction.

There is a risk of air pollution because it uses a large amount of bitumen.

There is a need for more sophisticated equipment, such as bitumen injection equipment and mixers.

The weather conditions can have a significant effect on the process and must be monitored, which can delay construction projects.

To know more about the combination, visit:

https://brainly.com/question/28359481

#SPJ11

The ratio of O: Si when 30wt% Y2O3 is added to SiO2 is approximately 3.24. The molecular mass of SiO2 is 60.08 g/mol, and the molecular mass of Y2O3 is 225.83 g/mol.

To calculate the ratio of O: Si, we first determine the number of moles of SiO2 and Y2O3 based on their given masses. Assuming 100 g of SiO2 and 30 g of Y2O3, we find the number of moles of SiO2 to be 1.6658 and the number of moles of Y2O3 to be 0.1329.

Next, we calculate the number of moles of O in SiO2, which is twice the number of moles of SiO2 (2 * 1.6658 = 3.3317). Similarly, the number of moles of O in Y2O3 is three times the number of moles of Y2O3 (3 * 0.1329 = 0.3987).

The number of moles of Si in SiO2 is equal to the number of moles of SiO2 (1.6658), and the number of moles of Y in Y2O3 is twice the number of moles of Y2O3 (2 * 0.1329 = 0.2658).

Adding up the total number of moles of Si and O in SiO2 and Y2O3 gives us 2.3303 (1.6658 + 0.3987 + 0.2658).

Finally, the ratio of O: Si is the ratio of the number of moles of O to the number of moles of Si, which is approximately 3.24 (3.3317 / 1.6658).

Learn more about ratio

https://brainly.com/question/32531170

#SPJ11

The ratio O:Si when 30wt% Y2O3 is added to SiO2 is approximately 0.343.

To calculate the ratio O:Si when 30wt% Y2O3 is added to SiO2, we need to determine the number of moles of oxygen and silicon in the mixture.

Let's start by calculating the number of moles of Y2O3. Given that the atomic mass of yttrium (Y) is 88.91 g/mol and the atomic mass of oxygen (O) is 16.00 g/mol, the molar mass of Y2O3 can be calculated as follows:

Molar mass of Y2O3 = (2 * atomic mass of Y) + (3 * atomic mass of O)
                  = (2 * 88.91 g/mol) + (3 * 16.00 g/mol)
                  = 177.82 g/mol + 48.00 g/mol
                  = 225.82 g/mol

Next, we need to determine the number of moles of Y2O3 in the mixture. Since the mixture contains 30wt% Y2O3, we can calculate the mass of Y2O3 as follows:

Mass of Y2O3 = 30wt% * Total mass of mixture

Let's assume the total mass of the mixture is 100 grams. Then,

Mass of Y2O3 = 30wt% * 100 grams
            = 30 grams

Now, we can calculate the number of moles of Y2O3:

Number of moles of Y2O3 = Mass of Y2O3 / Molar mass of Y2O3
                      = 30 grams / 225.82 g/mol
                      = 0.133 moles

Since Y2O3 contains 3 moles of oxygen (O) per mole of Y2O3, the number of moles of oxygen in the mixture is:

Number of moles of O = Number of moles of Y2O3 * 3
                    = 0.133 moles * 3
                    = 0.399 moles

Now, let's calculate the number of moles of SiO2 in the mixture. Given that the atomic mass of silicon (Si) is 28.08 g/mol and the molar mass of SiO2 is 60.08 g/mol, we can calculate the number of moles of SiO2 as follows:

Number of moles of SiO2 = Mass of SiO2 / Molar mass of SiO2

Assuming the total mass of the mixture is 100 grams, the mass of SiO2 can be calculated as:

Mass of SiO2 = Total mass of mixture - Mass of Y2O3
            = 100 grams - 30 grams
            = 70 grams

Now, we can calculate the number of moles of SiO2:

Number of moles of SiO2 = 70 grams / 60.08 g/mol
                      = 1.165 moles

Finally, we can calculate the ratio O:Si:

Ratio O:Si = Number of moles of O / Number of moles of Si
          = 0.399 moles / 1.165 moles
          = 0.343

Learn more about ratio

https://brainly.com/question/32531170

#SPJ11

Answer:

the polar form of z = 1 + √3i is 2(cos(π/3) + i * sin(π/3)).

Step-by-step explanation:

The quadratic equation for ternary systems can be written as; [tex]$$ f\left(V\right)=0 $$[/tex], [tex]$$ f'\left(V\right)=0 $$[/tex]. Solving this quadratic equation using the discriminant method gives us the solution for V.

The Rachford Rice equation can be written as;

[tex]$$ \sum\limits_{i=1}^n\frac{V_i}{v_i+\left(1-V\right)b_i}=0 $$[/tex]

Where;[tex]$V_i$[/tex]: the molar volume of component i.

[tex]$v_i$[/tex]: the specific volume of component i.

[tex]$b_i$[/tex]: the molar quantity of the component i.

The quadratic equation can be formulated from the RR equation to determine the vapor-liquid equilibrium of ternary systems. The formula is given as;

[tex]$$ f\left(V\right)=\sum\limits_{i=1}^n\frac{\left(Vb_i\right)}{v_i+\left(1-V\right)b_i}=0 $$[/tex]

Where;

[tex]$$ f\left(V\right)=\sum\limits_{i=1}^n\frac{\left(Vb_i\right)}{v_i+\left(1-V\right)b_i} $$[/tex]

Therefore, if we differentiate the above equation;

[tex]$$ f'\left(V\right)=\frac{d}{dV}\sum\limits_{i=1}^n\frac{\left(Vb_i\right)}{v_i+\left(1-V\right)b_i} $$[/tex]

This gives;

[tex]$$ f'\left(V\right)=\sum\limits_{i=1}^n\frac{b_i}{\left(v_i+\left(1-V\right)b_i\right)^2} $$[/tex]

For a ternary system, $n=3$. Therefore, we get;

[tex]$$ f'\left(V\right)=\frac{b_1}{\left(v_1+\left(1-V\right)b_1\right)^2}+\frac{b_2}{\left(v_2+\left(1-V\right)b_2\right)^2}+\frac{b_3}{\left(v_3+\left(1-V\right)b_3\right)^2} $$[/tex]

To obtain the second derivative of the above equation with respect to V, we differentiate

[tex]$f'(V)$[/tex]; [tex]$$ f''\left(V\right)=\frac{d}{dV}\sum\limits_{i=1}^n\frac{b_i}{\left(v_i+\left(1-V\right)b_i\right)^2} $$[/tex]

Simplifying, we get;

[tex]$$ f''\left(V\right)=\sum\limits_{i=1}^n\frac{2b_i^2}{\left(v_i+\left(1-V\right)b_i\right)^3} $$[/tex]

For a ternary system, [tex]$n=3$[/tex]. Therefore, we get;

[tex]$$ f''\left(V\right)=\frac{2b_1^2}{\left(v_1+\left(1-V\right)b_1\right)^3}+\frac{2b_2^2}{\left(v_2+\left(1-V\right)b_2\right)^3}+\frac{2b_3^2}{\left(v_3+\left(1-V\right)b_3\right)^3} $$[/tex]

The quadratic equation for ternary systems can be written as;

[tex]$$ f\left(V\right)=0 $$[/tex]

[tex]$$ f'\left(V\right)=0 $$[/tex]

Solving this quadratic equation using the discriminant method gives us the solution for V.

Learn more about quadratic equation visit:

brainly.com/question/30098550

#SPJ11

The position of  depends on the specific experiment or measurement being performed. The sample is placed in the path of one of the beams, between the beam splitter and mirror M2. This allows the sample to interact with one of the beams, causing a phase shift or other effects that  observed in the interference pattern.

A Michelson interferometer is an optical instrument used to measure small changes in the position of mirrors, the refractive index of gases, or the wavelength of light. It consists of the following components:

Laser Source: The laser emits a coherent beam of light with a single wavelength. It provides a stable and monochromatic light source for the interferometer.

Beam Splitter: The beam splitter is a partially reflecting mirror that splits the incoming laser beam into two equal parts. It reflects a portion of the light towards mirror M1 and transmits the remaining portion towards mirror M2.

Mirror M1: Mirror M1 reflects the incoming light from the beam splitter back towards the beam splitter. This mirror moved along the optical path, allowing for the introduction of a sample or the measurement of small changes.

Mirror M2: Mirror M2 is positioned perpendicular to the path of the transmitted light from the beam splitter. It reflects the light towards the beam splitter again.

Sample: The sample is placed in the path of one of the beams, typically between the beam splitter and mirror M2. It a gas cell, a transparent material, or any object that you want to study using interferometry.

Detector: The two beams recombine at the beam splitter, and the interference pattern is formed. The detector, such as a screen or a photodetector, measures the intensity of the combined beams.

To know more about interference here

https://brainly.com/question/31857527

#SPJ4

The PPMV composition of SO2 in the flue gas can be calculated as follows: PPMV of SO2 = (0.06/100) x 10^6 = 600 PPMV. The PPMV composition of SO2 in the flue gas is 600 PPMV.

Coal is a black or dark brown rock that occurs naturally. It is made up of the compressed and decomposed remains of prehistoric plant and animal life. Coal has a typical elemental composition of H 4.9%, C 75%, N 1.8%, O 10%, sulfur 1.2%, and the rest is inert ash. When coal is burned with 250% excess oxygen, using air as the oxygen source, 95% of the coal completely burns to CO2, while the remaining 5% C partially burns to CO.

Theoretical Orsat Analysis:

Given that the coal is burnt with 250% excess oxygen, the theoretical Orsat analysis when this coal is burnt in % composition can be calculated as follows:

As 95% of the coal is burned completely to CO2, the amount of CO2 produced can be calculated as follows:CO2 produced = 0.95 x 75 = 71.25%Since the remaining 5% C partially burns to CO, the amount of CO produced can be calculated as follows:

CO produced = 0.05 x 75 = 3.75%The amount of oxygen that will be consumed can be calculated as follows:O2 consumed = (71.25 + 3.75) - 10 = 65%The amount of nitrogen in the flue gas can be calculated as follows:N2 = 100 - (71.25 + 3.75 + 65) = - 40.0%The negative result indicates that there is no nitrogen in the flue gas. PPMV composition of SO2 in the flue gas can be calculated as follows:

Given that the percentage of sulfur in coal is 1.2%, the amount of SO2 produced can be calculated as follows:SO2 produced = (1.2 x 5) / 100 = 0.06%Since the coal is burnt with 250% excess oxygen, SO2 is fully oxidized to SO3.

Therefore, the percentage of SO3 produced is the same as the percentage of SO2 produced.SO3 produced = 0.06%The volume of flue gas produced can be assumed to be 100 m3. The amount of SO3 produced is, therefore, equal to 0.06 m3.

Learn more about oxidized:

https://brainly.com/question/13182308

#SPJ11

The temperature in Celsius is approximately 20°C.

Option  21°C is correct.

To convert a temperature from degrees Celsius (C) to degrees Fahrenheit (F), the formula F = (9/5)C + 32 is used.

In this case, we are given the temperature in Fahrenheit (69.8°F) and we need to find the equivalent temperature in Celsius.

Rearranging the formula to solve for C, we have:

C = (F - 32) [tex]\times[/tex] (5/9)

Substituting the given Fahrenheit temperature into the equation, we get:

C = (69.8 - 32) [tex]\times[/tex] (5/9)

C = 37.8 [tex]\times[/tex] (5/9)

C ≈ 20

Therefore, the temperature in Celsius is approximately 20°C.

Based on the answer choices provided, the closest option to the calculated value of 20°C is 21°C.  

For similar question on temperature.

https://brainly.com/question/26866637  

#SPJ8