Answer:
medium sized ears
Explanation:
What size resistor would produce a current flow of 5 Amps with a battery voltage of 12.6 volts
Answer:
resistance = 2.52 ohms
Explanation:
from the formula
V =IR
Voltage = (current)(resistance)
Resistance =
R=
R= 2.52 ohms
Your vehicle is/ are not part of regulated safety system 
Answer:
Amends the FMVSS on air brake systems to improve the stopping distance performance of truck tractors. The rule requires the vast majority of new heavy truck tractors to achieve a 30 percent reduction in stopping distance compared to currently required levels. For these heavy truck tractors (approximately 99 percent of the fleet), the amended standard requires those vehicles to stop in not more than 250 feet when loaded to their gross vehicle weight rating (GVWR) and tested at a speed of 60 miles per hour (mph). For a small number of very heavy severe service tractors, the stopping distance requirement will be 310 feet under these same conditions. In addition, this final rule requires that all heavy truck tractors must stop within 235 feet when loaded to their “lightly loaded vehicle weight” (LLVW).
Amends the FMVSS on air brake systems to improve the stopping distance performance of truck tractors. The rule requires the vast majority of new heavy truck tractors to achieve a 30 percent reduction in stopping distance compared to currently required levels. For these heavy truck tractors (approximately 99 percent of the fleet), the amended standard requires those vehicles to stop in not more than 250 feet when loaded to their gross vehicle weight rating (GVWR) and tested at a speed of 60 miles per hour (mph). For a small number of very heavy severe service tractors, the stopping distance requirement will be 310 feet under these same conditions. In addition, this final rule requires that all heavy truck tractors must stop within 235 feet when loaded to their “lightly loaded vehicle weight” (LLVW).
Answer:
power window controls
Explanation:
Why is not adjust the depth of cut in the center of work piece in facing turning?
Answer:
I am not sure it's confusing
A tank is filled with oil whose density is 850kg/m3. If the volume of the tank is 2.0m3, determine the amount of mass m in the tank
Answer:
1700 kg
Explanation:
Determine the total mass of the oil, m, by multiplying the density,
p= 850 kg/m3
to the volume, V = 2m3 or m=p x v.
m=pxv.
m= p x v = 850 kg / m3 x 2
m3 = 1700 kg
1. A drawing of a cabinet shows that its dimensions are 9cm. by 4cm. The drawing indicates 1:50 scaling. What are the actual dimensions of the cabinet?
2. Bongbong is tasked to draw a floor plan with a scale of 1:100. If the total length of the actual house is 8 meters, what will be its corresponding measurement in centimeters in floor plan?
3.The length of a bedroom measures 2.5 m., what will be the measurement in centimeters to be used in the drawing if it is in 1:50 scale?
Explanation:
This means that for every 1 cm on the drawing, there is 80 cm in reality. To put it another way, take this
1:80 means that the building is 80 times the size of the drawing
80:1 means that the drawing is 80 times the size of the building
If it were 80:1, the drawing itself would be over 100m long.
The disk spins about the fixed axis BB, which is inclined at the angle α to the vertical z-axis. A small block A is placed on the disk in its lowest position P at a distance r from the axis when the disk is at rest. The angular velocity ω = theta dot. is then increased very slowly, starting from zero. At what value of ω will the block slip, and at what value of θ will the slip first occur? Use the values α = 25°, r = 0.55 m, and μs = 0.67. What is the critical value of ω if α = 0?
Answer: A small block A is placed on the disk in its lowest position P at a distance r from the axis when the disk is at rest. The angular velocity
Explanation:
2. A silo (base not included) is to be constructed in the form of a cylinder surmounted by a hemisphere. The cost of construction per square unit
of surface area is twice as great for the for the hemisphere as it is for the cylindrical side wall. Determine the dimensions to be used if the volume is fixed and the cost of construction is to be kept to a minimum. Neglect the thickness of the silo and waste in construction.
An extremum is a point where the function has its highest or lowest value, and at which the slope is zero.
The dimensions to be used if the volume is fixed and the cost of construction is to be kept to a minimum is as follows;
Height of cylinder = 2 × Radius of cylinderReason:
The given parameters are;
Form of silo = Cylinder surmounted by a hemisphere
Cost of construction of hemisphere per square unit = 2 × The cost of of construction of the cylindrical side wall
Required:
The dimensions to be used if the volume is fixed and the cost of construction is to be kept to a minimum
Solution:
The fixed volume of the silo, V, can be expressed as follows;
[tex]V = \pi \cdot r^2 \cdot h + \dfrac{2}{3} \cdot \pi \cdot r^3[/tex]
[tex]h = \dfrac{V - \dfrac{2}{3} \cdot \pi \cdot r^3 }{\pi \cdot r^2 }[/tex]Where;
h = The height of the cylinder
r = The radius of the cylinder
The surface area is, Surface Area = 2·π·r·h + 2·π·r²
The cost, C = 2·π·r·h + 2×2·π·r² = 2·π·r·h + 4·π·r²
Therefore;
[tex]C = 2 \times \pi \times r\times \dfrac{V - \dfrac{2}{3} \cdot \pi \cdot r^3 }{\pi \cdot r^2 } + 4 \cdot \pi \cdot r^2 = \dfrac{8 \cdot r^3 \cdot \pi + 6 \cdot V}{3 \cdot r}[/tex]
[tex]C = \dfrac{8 \cdot r^3 \cdot \pi + 6 \cdot V}{3 \cdot r}[/tex]At the minimum value, we have;
[tex]\dfrac{dC}{dr} =0 = \dfrac{d}{dr} \left(\dfrac{8 \cdot r^3 \cdot \pi + 6 \cdot V}{3 \cdot r} \right) = \dfrac{16 \cdot r^3 \cdot \pi - 6 \cdot V}{3 \cdot r^2}[/tex]Which gives;
16·π·r³ = 6·V
[tex]V = \dfrac{16 \cdot \pi \cdot r^3}{6} = \dfrac{8 \cdot \pi \cdot r^3}{3}[/tex]Which gives;
[tex]h = \dfrac{\dfrac{8 \cdot \pi \cdot r^3}{3} - \dfrac{2}{3} \cdot \pi \cdot r^3 }{\pi \cdot r^2 } = 2 \cdot r[/tex]
h = 2·r
The height of the silo, h = 2 × The radius, 2
Therefore, the dimensions to be used if the volume is fixed and the cost is to be kept to a minimum is, height, h = 2 times the radius
Learn more about extremum point here:
https://brainly.com/question/2869450
A house that was heated by electric resistance heaters consumed 1500 kWh of electric
energy in a winter month. If this house were heated instead by a heat pump that has an
average COP of 2.5, determine how much money the homeowner would have saved
that month. Assume a price of Tk 6/kWh for electricity.
Answer:
2.5=1500/Whp=> Whp=600 kWh
delWgain=1500-600=900 kWh
Money saved= 900* 6tk*=5400 tk
A gas turbine power plant is being designed using an air-standard Brayton cycle. Air enters the compressor with a volumetric flow rate of 7 m3 /s at 100 kPa, 300 K. The turbine inlet temperature is expected to be 1400 K. The compressor pressure ratio is 10. The turbine exhaust goes back to the atmosphere at 100 kPa. (a) Draw the schematic and T-s diagrams. (b) Determine the thermal efficiency. (c) Determine the back work ratio of this power plant.
check all the photos
Which of the following workers are not likely to be paid during an election?
campaign press secretary
volunteer coordinator
poll worker
director of communications
Answer:
volunteer coordinator
Explanation:
because they are volunteering for that and in most of the cases they do not expect to be paid
Why did you choose agricultural and biosystem as a course? Help me guys
Answer:
To be able to develop as a human and give back to the community. To ensure that people have safe food and water to drink, clean fuel and energy sources, and in general a safe enviornment to live in.
Explanation:
The reasons why someone might choose to study agricultural and biosystems engineering are highly individual and can depend on a variety of factors, such as personal interests, career goals, and educational background.
What is agricultural and biosystem engineering?Many students who decide to study agricultural and biosystems engineering are interested in farming, making food, and sustainable agriculture. They might want to find new ways to make more food or improve how farmers work.
Agricultural and biosystems engineering is a field that focuses on creating systems and processes that are good for the environment.
Students who care about the environment may decide to learn about this subject because it focuses on reducing waste, saving resources, and causing less harm to the environment.
Agricultural and biosystems engineering is a field that combines different areas of knowledge such as biology, chemistry, physics, and computer science. Students who like to work in different subjects might find this field perfect for their interests and abilities.
Learn more on biosystem on https://brainly.in/question/53109597
#SPJ2
Where you attend college could costmore to borrow and refinance loans
After turning off the television, you approach it. As you get close, but not touching it, the hairs on your arm start to stand up. This is an excellent example of static charge built up by_______
If a construction company is considering a new type of material to use in their construction, which factors would they
focus on? (Select all that apply.)
that the new material does the same thing as an existing material but better
that the new material does the same thing as an existing material but cheaper
that the science behind the material be familiar to and understood by its employees
that the properties of the new material meet their construction needs
I would honestly select every one of the given options. Gor a company evaluating this new material it would be very valuable to hit each of these factors.
__________ is an example of an electrical device.
Plug
Cord
Cable
All of the above
Explanation:
is an example of an electrical device.
Cable
It is given thatopen parenthesis, x minus 2y, close parenthesis, times open parenthesis, x + 2y, close parenthesis, = 4Quantity A: x squared, minus, 4 times the quantity y squared Quantity B: 8 A. Quantity A is greater. B. Quantity B is greater. C. The two quantities are equal. D. The relationship cannot be determined from the information given.
Answer:
Quantity B is greater.
Explanation:
Given:
(x -2y)(x +2y) = 4
A = x² -4y²
B = 8
Find:
the relationship between A and B
Solution:
The given expression can be expanded to give ...
x(x +2y) -2y(x +2y) = x² +2xy -2xy -4y² = x² -4y²
This is precisely the expression designated as A. Its value is 4.
4 < 8
A < B
Quantity B is greater.
Which of these include some basic characteristics of taxi services? (Select all that apply.)Transactions are often negotiated at the time of use.Many taxi services are one-person and mom-and-pop businesses.Few taxi services are as extensive in range as either urban mass transit orcommercial airlines options.They do not usually involve long-term planning, beyond a single use.
The basic characteristic of the taxi service is that some taxi services are as extensive in range as either urban mass transit or commercial airlines.
Waht is a taxi service?A taxi is a cab that one hired b a single person or a group and they have a nonshared ride. The taxi service is found in various international destinations all over the world and especially at the airports, restaurants and hotels. Some place's taxi services are extensive and include the urban transits.
Find out more informaion about the taxi services.
brainly.com/question/25672789
i need your help to answer in the picture plss help me!
this looks like its the different phases of a single cylinder 4 stroke engine what are you doing in the picture or assignment though matching the numbers to the descriptions on the side?
How to make coconut harder
Now hear me out: Steel-Coated Coconuts
If you want to make a coconut harder you can take that shell up to heights its natural husk never even knew it could reach! Combining the raw, brown scraglley-ness with the tough, durable properties of steel would most definitely make a coconut harder.
Valid answer? Probably not.
Thank you for coming to TedTalk :))
Which of the following procedures best applies to assessing the embodied energy of a building?
analyzing the building’s materials
analyzing the building’s function
analyzing the building’s age
analyzing the building’s blueprints
100 POINTS
analyzing building materials???????????? but i can try i think it is analyzing the materials of the building
why a hard disk called a random access stroage device
RAM is called “random access” because any storage location on the computer can be accessed directly (as opposed to randomly).
For the siphon shown in Figure, determine the flowrate out of the siphon and the absolute
pressure at the crest of the siphon assuming that there is no losses through the pipe.
2.00 m
Del
50-mm-diameter
Oil (s.g. =0.82)
5.00 m
The radiation meter is showing radiation 2x as much as background. Is this a hot zone? If so why or why not?
Answer:
This is not a clear indication of the hot zone as the information of the radioactivity of the background is not provided clearly.
Explanation:
According to IAEA as well as NRCP, the hot area is defined on the basis of the radioactivity reading it shows instead of contrast or comparative reading from the background. The value of radiation activity which will be required to declare an area as hot zone is if it is greater than 0.1 mSv/h or [tex]1.5091\times 10^{29} kg^{-1} s^{-1}[/tex].
a hallow steel tube 3.5m long has external diameter of 120mm. in order to determine the internal diameter the tube was subjected to a tensile load of 400KN and extension was measured to be 2 mm. if the modulus of elasticity for the tube material is 200 GPa. determine the internal diameter of the tube.
Answer:
Please check the photo (solve)
The device in Figure P6.27 is a sloshing bath used to wash vegetable produce. For the configuration shown, use the relative velocity method to graphically determine the angular velocity of the water bath as the crank is driven clockwise at 75 rpm.
check photo (answer)
The angular velocity of the water bath as the crank is driven clockwise is 6.66rpm/ms.
How to calculate the angular velocity?From the complete information, we are to use the relative velocity method to determine the angular velocity of the water bath.
This will be:
60/V = 1085.4/120.58
Cross multiply.
(1085.4 × V) = (120.58 × 60)
V = (120.58 × 60/1085.4)
V = 6.66rpm/ms
Learn more about angular velocity on:
https://brainly.com/question/626479
#SPJ2
Which tool or device is an example of a pneumatic power system that uses compressed air to tighten or loosen an object? a jackhammer a lifting system a turbine an impact driver
Answer:
A jackhammer.
Explanation:
A jackhammer is a pneumatic device that was invented by William Mcreavy. Later, Mcreavy sold the patent of jackhammer to Charles Brady King. The tool is a combination of chisel and hammer. The tool is powered by compressed air to tighten or loosen an object. By using pressurized air, jackhammers help workers to drill and lossen an object.
Therefore, option A is correct.
Answer:
Impact Driver
Explanation:
Why do some ladders have a white tip or reflective tape attached to the tip?
Determine the gage pressure at the center of pipe A in pounds per square inch and
in kilopascals.
Answer: the stress is 384 pounds per square inch.
Step-by-step explanation:
Let S represent the stress in the material of the pipe.
Let P represent internal pressure of the pipe.
Let D represent internal diameter of the pipe.
Let T represent the thickness of the pipe.
The stress in the material of a pipe subject to internal pressure varies jointly with the internal pressure and the internal diameter of the pipe and inversely with the thickness of the pipe. Introducing a constant of proportionality, k, the expression becomes
S = kPD/T
The stress is 100 pounds per square inch when the diameter is 5 inches, the thickness is 0.75 inch, and the internal pressure is 25 pounds per square inch. It means that
100 = (k × 25 × 5)/0.75
125k = 100 × 0.75 = 75
k = 75/125 = 0.6
The equation representing the relationship becomes
S = 0.6PD/T
If the internal pressure is 40 pounds per square inch, the diameter is 8 inches and the thickness is 0.50 inch, then the stress would be
S = (0.6 × 40 × 8)/0.5
S = 384
Alvaro designs machinery and equipment for ships. His job title is best described as . Jeanette draws maps and plans for freeway projects. Her job title is best described as . Joseph designs a new airport. His job title is best described as . Geraldine designs imaging systems that use light. Her job title is best described as .
Answer:
Alvaro designs machinery and equipment for ships. His job title is best described as Marine Engineer.
Jeanette draws maps and plans for freeway projects. Her job title is best described as Civil Drafter.
Joseph designs a new airport. His job title is best described as Transportation Engineer.
Geraldine designs imaging systems that use light. Her job title is best described as Photonics Engineer.
Hope this helps sorry I am late to respond, but anyone else who needs the answer it is here.
Based on the above, Alvaro is a Marine Engineer;
Jeanette is a Civil Drafter.Joseph is a Transportation Engineer.Geraldine is a Photonics Engineer.What is machinery and equipment?Machinery and Equipment are known to be a type of industrial tools, devices, and items that aids facilities.
Conclusively, They are said to be tangible personal property that are used as a tool for repair parts, etc. Professions in ship jobs includes, Marine Engineer, Photonics Engineer, etc.
Learn more about machinery and equipment from
https://brainly.com/question/1203520
Steam enters the first-stage turbine shown in the figure at 40 bar and 400oC with a mass flow rate of 60,000 kg/hr. Steam exits the first-stage turbine at 20 bar and 400oC. The steam is then reheated at constant pressure to 500oC before entering the second-stage turbine. Steam leaves the second stage as saturated vapor at 0.6 bar. Assume steady state operation and ignore stray heat transfer and kinetic and potential energy effects. Determine the volumetric flow rate of the steam at the inlet to the first-stage turbine, in m3/min, the rate of heat transfer to the steam flowing through the reheater, in kW, and the total power produced by the two stages of the turbine, in kW.
Answer:
a) 62460 kg/hr
(b) 17,572.95 kW
(c) 3,814.57 kW
Explanation: