The design of a concrete mix requires 1173 kg/m3 of gravel in dry condition, 582 kg/m3 of sand in dry condition, and 157 kg/m3 of free water. The gravel available at the site has a moisture content of 0.9% and absorption of 1.5%, and the available sand has a moisture content of 1.2 and absorption of 1.5%. What are the masses of gravel, sand, and water per cubic meter that should be used at the job site

A stall happens when the smooth airflow over the unmanned airplane`s wing is disrupted, and the lift degenerates rapidly. This is caused when the wing "exceeds its critical angle of attack."

The angle of attack refers to the angle at which the airplane's wing meets the air that is flowing over it. When an airplane actually is taking off, it is lifting the nose up into the air. And, if that nose continues to rise ultimately it reaches a point where the air is not able to smoothly flow over the wing, causing the airplane to drop. And, this is the point when the airplane exceeds its critical angle of attack.

Exceeding the critical angle of attack is known to be a stall. This has no concern with the engine stalling, it just concerns with the wings not producing enough lift to keep the airplane in the air.

You can learn more about critical angle of attack at

https://brainly.com/question/13209325

#SPJ

Answer:

Both pathways require workers to be creative, while the Science and Math pathway requires specialized knowledge in subject areas like physics or chemistry.

Answer:

Right B is right?

Explanation:

Tech B is correct it's a verified fact that some auto parts may contain asbestos.

Do auto parts contain asbestos?

Asbestos has been used in a wide range of automotive products, including brakes, clutches, hood liners, gaskets, heat shields, and many others.

Drum and disc brakes were traditionally made with 35% to 60% asbestos. It is still legal in the United States to sell asbestos-containing auto parts, and many brake and clutch parts contain up to 35% asbestos.

Contaminated parts have been found in vehicles of all types, including cars, trucks, motorcycles, buses, trains, and military vehicles. Elevators and other types of transportation machinery also used asbestos brakes.

To learn more about asbestos, visit: https://brainly.com/question/20715468

#SPJ4

Answer:

In a single-family residence, a line-voltage thermostat is primarily used to control heating and cooling systems.

Freezing prevents bacteria from growing. If food is heated sufficiently, parasites, viruses, and most bacteria are killed.

The curves look like a sine wave, with the number of rabbits and foxes both oscillating around a steady-state equilibrium. The presence of the constants for growth and death of both rabbits and foxes.

What is curves?
Curves is an international fitness franchise targeting women. It offers a 30-minute workout that combines strength training, cardio, and stretching. The circuit-style program is designed to help members reach their fitness goals while providing a supportive, non-threatening environment. The program also includes nutrition counseling, wellness education, and support from certified coaches.

This is because the predator-prey relationships in this system are cyclical, with the fox population increasing as the rabbit population increases, and vice versa.

To learn more about curves
https://brainly.com/question/13445467

#SPJ4

Answer:

Plain carbon steel has no or trace external elements while alloy steel has high amount of other elements.

Explanation:

Plain carbon steel has no or trace amount of other elements while alloy steel has high amount of other elements in their composition.

The presence of other elements in alloy steel improvise several physical properties of the steel while plain carbon steel has the basic properties.

The mass of sugar cane being fed to the process with this flowrate is 0.0014 kg/s.

Flowrate is the rate at which a fluid or gas passes through a given space or container over a period of time. It is usually expressed in terms of volume per unit of time, such as liters per second or gallons per minute. Flowrate is an important factor in many engineering and scientific applications, such as fluid dynamics, hydroelectric power generation, and chemical processing. It is also used to measure the flow of liquids and gases through pipes, valves, and other components of a system.

The mass of sugar cane being fed to the process can be calculated using the following equation:
Mass (kg/s) = Flowrate (m^3/s) * Density of the mixture (kg/m^3)
The flowrate can be calculated using the equation given:
q(m^3/s) = 0.0307 m^3/hr atm^1/2 √ Pmanometer
Therefore, the flowrate is:
q(m^3/s) = 0.0307 m^3/hr * (atm^1/2 * (6.3 in/12 in/ft)^1/2)
q(m^3/s) = 0.0015 m^3/s
The density of the mixture can be calculated using the following equation:
Density of the mixture (kg/m^3) = Mass of sugar (kg) / Volume of the mixture (m^3)
The mass of sugar can be calculated using the following equation:
Mass of sugar (kg) = Mass of the mixture (kg) * (Mass fraction of sugar (kg/kg) / Mass fraction of the mixture (kg/kg))
The mass of the mixture can be calculated using the following equation:
Mass of the mixture (kg) = Volume of the mixture (m^3) * Density of the mixture (kg/m^3)
The volume of the mixture can be calculated using the following equation:
Volume of the mixture (m^3) = Flowrate (m^3/s)
The mass fraction of sugar can be calculated using the following equation:
Mass fraction of sugar (kg/kg) = Mass of Sugar (kg) / Mass of the mixture (kg)
The mass fraction of the mixture can be calculated using the following equation:
Mass fraction of the mixture (kg/kg) = Mass of the mixture (kg) / Mass of the mixture (kg)
Substituting the values into the equation, we get:
Mass (kg/s) = 0.0015 m^3/s * (0.91 kg/m^3)
Mass (kg/s) = 0.0014 kg/s
Therefore, the mass of sugar cane being fed to the process with this flowrate is 0.0014 kg/s.

To learn more about flowrate
https://brainly.com/question/14291335
#SPJ4

Answer: None of the above

Explanation:

Business process modeling refers to the graphical representation of the business processes of a company, which is vital in the identification of potential improvements.

Business pticess modelling can be done through graphing methods, like data-flow diagram, flowchart etc. It is vital as business managers can effectively and quickly communicate their ideas.

It also enhances the customization of business processes, enhances the competitive advantage and enhances the process communication as well.

Therefore, the answer to the question will be "None of the above".

It is important to know the number of teeth on the two gears when calculating a bevel gear because the number of teeth determines the gear ratio, which in turn determines the torque and speed at which the gears will operate.

The gear ratio is calculated by dividing the number of teeth on the driving gear by the number of teeth on the driven gear.

If the number of teeth is not known, it would be impossible to accurately calculate the gear ratio and determine the performance of the gear set.

Additionally, the number of teeth also affects the meshing pattern and the contact ratio between gear teeth, which is also important to the gear's performance.

Read more about gear teeth here:

https://brainly.com/question/12761665

#SPJ1

Answer:

a) L = 50.01 nm

b) 99.98%

Explanation:

Determine the necessary precipitate spacing  and estimate the required percentage of precipitate phase

Given that the shear strength = G/100 by precipitation hardening

G = shear modulus

Radius of particles = 40 nm

attached below is the detailed solution

a) precipitate spacing ( L ) = √( 2π / f )  * R₁

                                       = √ ( 2π / 0.00719956 ) * 1.693 nm

hence L = 50.01 nm

b) Determine The percentage of precipitate phase that is required

( precipitation strength  /  peak strength ) * 100

= ( 18.4583 / 18.4604 ) * 100

= 99.98%

The choices that best describe the process of digitization are: Option A: binary-stored video. Option C converts analog video to digital video.

Information transformation into a digital format is referred to as digitization. Be aware that in this format, data is organized into discrete units of data called bits. As a result, the following options best represent the digitization process: Option A: binary-stored video. Option C converts analog video to digital video.  This is due to the fact that digital video is a key technology for both video conferencing and video messaging in addition to being a key technology for digital television. This was demonstrated by its use in messaging apps for confidential conversations and for hosting virtual conferences for business meetings amongst personnel.

Learn more about Digitization here:

https://brainly.com/question/28368732

#SPJ4

A geotechnical investigation is primarily concerned with testing the physical properties of the soil, to provide recommendations for foundation requirements, excavation stability, drainage and buried concrete design.

Answer:

Geotechnical investigation is: A surface exploration and subsurface exploration of a site.

Explanation:

What does Geotechnical investigation mean?

It's a primarily concerned with testing the physical properties of the soil, to provide recommendations for foundation requirements, excavation stability, drainage and buried concrete design.

Why Geotechnical is important?

It allow's Engineers to evaluate the stability and strength of the ground, including slopes and soil deposits, assess risks such as soil aggressivity to buried concrete, and help to determine what type of foundations and earthworks would be required within a (project) for example.

Answer:

s = 6.6

-25 + 5 × 6.6 = 8

Just let me know if you need any more help.

The energy of the magnetic and electric fields that have been stored can differ. A completely charged capacitor is linked in series with an inductor.

A passive-terminal electric device called an inductor, often referred to as a coil, choke, or reactor, stores electricity in a magnetic field when electric current passes through it. An insulated string twisted into a coil is typically included in an inductor. A passive digital component called an inductor can store electrical energy in the form of magnetic electricity. In essence, it uses a conductor that has been twisted into a coil; as electricity enters the coil from left to right, this will produce a magnetic field that rotates counter clockwise. The energy of the magnetic and electric fields that have been stored can differ.

Learn more about Inductor here:

https://brainly.com/question/29417056

#SPJ4

Answer:

The answer is "3,118 N"

Explanation:

Using the hookes laws:

[tex]y=\frac{stress}{strain}=\frac{\frac{F}{A}}{\frac{\Delta L}{L}}[/tex]

So,  

[tex]F=\frac{y \times \Delta L \times A}{L}\\\\[/tex]

    [tex]=\frac{110 \times 10^{3} \times 0.1 \times \frac{\pi}{4} \times 9.5^2 }{250}\\\\=\frac{110 \times 10^{3} \times 0.1 \times \frac{3.14}{4} \times 90.25 }{250}\\\\=3,117.235 \ N\\\\=3,118 \ N\\\\[/tex]

According to the question of disconnecting an air gun before inspection, tech B is correct.

What is gun?
Gun is a type of weapon that is typically used to fire bullets at a target. It is typically composed of a barrel, a chamber, a firing mechanism, and ammunition. Guns have been used for centuries as a tool for hunting, self-defense, and warfare. Guns are typically categorized by the type of ammunition they use, such as pistol, shotgun, or rifle. Guns can be used to shoot at a variety of targets, such as animals, clay pigeons, and even human targets. Guns are also used in competitive shooting sports. Although guns can be used for a variety of purposes, they have the

Although it is not possible to completely remove all hazards from a shop, it is important to take precautions such as disconnecting an air gun before inspecting it to help reduce the risk of injury.

To learn more about gun
https://brainly.com/question/17037232

#SPJ4

Answer:

Explanation:

From the given information:

The BOD of the wastewater can be determined by using the formula:

[tex]BOD _5 = \dfrac{DO_i-DO_f}{\dfrac{V_s}{V_b}}[/tex]

where;

[tex]BOD _5 =[/tex]biochemical oxygen demand = ???

[tex]DO_i=[/tex] initial dissolved oxygen = 9 mg/L

[tex]DO_f=[/tex] final dissolved oxygen = 4 mg/L

[tex]V_b =[/tex] sample of the bottle, which is normally 300 mL

[tex]V_s[/tex] = sample volume = 30 mL

[tex]BOD _5 = \dfrac{9-4}{\dfrac{30}{300}}[/tex]

[tex]BOD _5 = \dfrac{5}{\dfrac{1}{10}}[/tex]

[tex]BOD _5 = 5\times{\dfrac{10}{1}}[/tex]

[tex]\mathbf{BOD _5 = 50 \ mg/L}[/tex]

The ultimate Carbonaceous BOD is estimated from the formula:

[tex]y_t = L_o-L_t \\ \\ y_t = L_o-L_oe^{-kt} \\ \\ y_t = L_o (1-e^{-kt})[/tex]

Making [tex]L_o[/tex] the subject, we have:

[tex]L_o = \dfrac{y_t}{(1-e^{-kt}} \\ \\ L_o = \dfrac{50}{1 - e^{-0.25*5}}[/tex]

[tex]L_o[/tex] = 70 mg/L

c) The BOD left over after five days = [tex]L_oe^{-kt}[/tex]

= [tex]70 \times e^{-0.25 *5}[/tex]

= 20 mg/L

d) The reaction constant rate is estimated as follows:

Recall that:

[tex]\mathbf{BOD _5 = 50 \ mg/L}[/tex]

Since DO measure 2 mg/L;

After 30 days, [tex]BOD_{30} = (9-2) \times 10 = 70 \ mg/L[/tex]

Therefore, the reaction rate constant is:

[tex]\dfrac{50 \ mg/L}{70 \ mg/L} =\dfrac{1-e^{-k*5}}{1-e^{-k*30}} \\ \\ 50 (1-e^{-k*30}) = 70 (1-e^{-k*5}) \\ \\ K = 0.25 /day[/tex]

The resulting stress at the top and bottom surfaces is 837.5 N/m^2 and -837.5 N/m^2, respectively. The top surface is in compression and the bottom surface is in tension.

What is stress?
Stress in engineering is the amount of force per unit area placed on a material or structure. It can be physical, or it can be psychological. Stress can be positive or negative. Positive stress can cause a material to become stronger, while negative stress can cause it to become weaker or even fail. Stress can also refer to the amount of strain a material must endure before it yields or breaks. Stress is measured in terms of pounds per square inch (psi) or newtons per square meter (N/m2). Stress analysis is important in engineering as it helps to identify potential failure points in a design, or to determine how much a material can handle before it breaks. Stress analysis is used to ensure the safety and integrity of products, structures, and machines.

To learn more about stress
https://brainly.com/question/13260444

#SPJ4

The first equation is linear, the second equation is nonlinear, the third equation is nonlinear, the fourth equation is nonlinear, the fifth equation is nonlinear, and the sixth equation is nonlinear.

What is equation?
An equation is an expression that contains an equal sign and relates two or more mathematical quantities. It typically consists of constants, variables, and symbols, and can be written in different forms such as standard form, slope-intercept form, and factored form. Equations are used to describe relationships between variables, and they can be used to solve a wide range of problems, from basic arithmetic to advanced calculus and physics. Equations are also used to model real-world phenomena, such as electricity, kinematics, and quantum mechanics. By studying equations and their solutions, we can gain a deeper understanding of the physical world around us.

To learn more about equation
https://brainly.com/question/24179864

#SPJ4

The energy stored in the two rubber bands of the catapult just before release can be calculated as follows: Area of Rubber Bands = (4 mm) x (300 mm) = 1200 mm2, Modulus of Rubber = 10-3 GPa = 10,000 N/mm2 Strain = (3 x Original Length) / (Original Length) =  Energy = (1200 mm2) x (10,000 N/mm2) x (3) = 36,000,000 Nmm or 36,000 J

Energy is the capacity of a physical system to do work or produce heat. It is the fundamental source of virtually all movement and change on Earth. In physics, energy is a property of objects which can be transferred to other objects or converted into different forms. Examples of energy include light, electricity, heat, sound, and kinetic energy. Energy can be generated from a variety of sources including fossil fuels, nuclear power, and renewable sources such as wind, solar, and hydropower. Energy plays a crucial role in the economic and social development of societies, enabling the production of goods and services and the delivery of basic services such as heating, cooling, and lighting. The efficient and responsible use of energy is essential to sustainable development.

To know more about energy here:

brainly.com/question/1932868

#SPJ4

Answer:

Diameter of pipe is 0.535 ft

Explanation:

see attachment, its works out 1st half

The following is true about vehicles displaying a diamond-shaped sign that indicates a hazardous load:

They must stop before a cross railroad track.

A hazardous load is any load determined by the Minister to be capable of posing a risk to health, safety, or property when transported on a public road. A hazardous load is defined as any load that has been prescribed by the Council in the Gazette as being capable of posing a risk to health, safety, and property when transported along the Regional Trunk Road Network.

A hazardous substance is any substance that is I listed, classified, or regulated in accordance with any environmental law; (ii) any petroleum product or by-product, asbestos-containing material, lead-based paint or plumbing, polychlorinated biphenyls, radioactive materials, or radon; or (iii) any other substance that is the subject of regulatory action by any governmental entity in accordance with any environmental law.

Learn more about hazardous load

https://brainly.com/question/28197708

#SPJ4

gove it to me. I'll do my best

In the given question, Moist unit weight = 115lbs/ft³, Dry unit weight = 103.6 lbs/ft³, Void ratio = 0.626,  Porosity = 0.385 and Degree of saturation =  47.4%

Porosity, also known as void fraction, is a measure of the void (i.e., "empty") spaces in a material. It ranges from 0 to 1, or as a percentage, between 0% and 100%, and represents the volume of voids over the total volume. Some tests, strictly speaking, measure the "accessible void," or the total volume of void space that is reachable from the surface (cf. closed-cell foam).

Porosity in a substance or part can be tested in a variety of ways, including through industrial CT scanning. The word "porosity" is used in a variety of disciplines, including pharmaceutics, ceramics, metallurgy, materials, manufacturing, petrophysics, hydrology, earth sciences, soil mechanics, and engineering.

a. Moist unit weight

W/V = 23/0.2 = 115lbs/ft³.

b.  Dry unit weight

89℅ of 115 = 103.6 lbs/ft³

c. Void ratio = volume of void/ volume of total sample

                     = (2.7 × 62.4)/103.6

                     = 0.626

d. Porosity = 0.626/1+0.626

                  = 0.385

e. Degree of saturation =  47.4%

Learn more about Porosity

https://brainly.com/question/2593663

#SPJ4

According to the question of vehicle which is only going to run for a few minutes, tech A is correct.

What is vehicle?
Vehicles are any mode of transportation that can be used on land, sea, or air. They are an important part of modern transportation and include cars, trucks, buses, motorcycles, boats, trains, and airplanes. They provide an efficient way to travel, while also allowing people to transport goods and materials. Vehicles are powered by a variety of sources, including gas and electricity. Advanced technology has allowed for the development of self-driving vehicles, which are becoming increasingly popular.

Caution and danger signs indicate a potentially hazardous situation, and an exhaust extraction hose should be used whenever a vehicle is running, regardless of how long it is running for.

To learn more about vehicle
https://brainly.com/question/28539698

#SPJ4

The controller PB is 0.22, the range of the controller pressure is between 3 to 13 psig, the controller setpoint is at 72°F, and the output pressure at that temperature is 3 psig while the controller output pressure at 76°F is 6 psig

A controller system is a type of feedback system used to regulate the performance of an output device by comparing the output to a desired set point. It uses the difference between the two values (error) to continuously adjust a control input to reduce the error. In simple terms, the controller system monitors, adjusts, and regulates the operations of the output device to achieve a desired result. Common examples of controllers include thermostats, cruise control systems, and PID controllers.

(a) Controller PB setting when remote sensors with spans of 50°F, 150°F, and 200°F are used:

This can be calculated as;

PB = (72°F - 50°F) / (200°F - 50°F) = 0.22

(b) Controller pressure range:

The range of the controller pressure is  3 - 13 psig

(c) Controller setpoint:

The controller set point is 72°F

(d)

The controller output pressure when T = 72°F while using the same sensors as in (a) is 3 psig

(e)

The controller output pressure at T = 76°F is  6.6 psig

(f) To predict the output pressure of the controller when T = 80°F with three remote sensors having spans of 50°F, 150°F, and 200°F are used will be 11.2 psig

Learn more on controller system here;

https://brainly.com/question/25480553

#SPJ1

The angle grinder disc is turned at speeds that range from 5000 to 12,000 rpm.

An angle grinder is a tool for rough grinding and cutting. An angle grinder tool with the correct disc can replace a variety of instruments, making even the most time-consuming and labor-intensive tasks faster and easier.

The term rpm refers to the number of times per minute that something will go around in a circle. The term rpm stands for revolutions per minute.' Both engines were set at 2,500 rpm.

Therefore, the angle grinder disc is spun at speeds ranging from 5000 to 12,000 revolutions per minute.

To learn more about angle grinder, refer to the link:

https://brainly.com/question/29563148

#SPJ1

The elevation of lowest point of the curve is 445.077 ft.

Height above or below the mean sea level is referred to as elevation. A map's elevation can be depicted either by labelling the precise elevations of specific points or by using contour lines, which link points of the same elevation. Topographic maps are depicted as having elevations.

Calculate rate of change of the curve as below:

[tex]$$\begin{aligned}r & =\frac{g_2-g_1}{L} \\& =\frac{2.5-(-4.0)}{\left(\frac{400}{100}\right)} \\& =1.625 \%\end{aligned}$$[/tex]

Calculate distance from PC to the lowest point as below:

[tex]$$\begin{aligned}X & =\frac{-g_1}{r} \\& =\frac{-(-4.0 \%)}{1.625 \%} \\& =2.462 \mathrm{ft}\end{aligned}$$[/tex]

Calculate the elevation of the lowest point of the curve as below:

[tex]$$\begin{aligned}Y & =Y_{P C}+g_1 X+\frac{r}{2} X^2 \\& =450\mathrm{ft}+(-4.0 \times 2.462)+\frac{1.625}{2}(2.462)^2 \\& =450\mathrm{ft}-9.848 \mathrm{ft}+4.925 \mathrm{ft} \\& =\mathbf{445.077} \mathrm{ft}\end{aligned}$$[/tex]

Thus, the elevation of lowest point of the curve is 445.077ft.

Learn more about elevation

https://brainly.com/question/29477960

#SPJ4