The circulation rate of coke between the reactor and the burner is Coke production rate is 40 lb/h.The Coke consumption rate in the burner is 30 lb/h.The specific heat of carbon is 0.19 Btu/lb.°F.The Heat transfer = 30 lb/h * 0.19 Btu/lb.°F * 500 °F. TheCirculation rate of coke = Heat transfer = 30 lb/h * 0.19 Btu/lb.°F * 500 °F
1. Determine the coke production rate:
Given that 2,000 pounds per hour of vacuum residue is fed into the flexicoker and the net coke production is 2.0 wt%, we can calculate the coke production rate as follows:
Coke production rate = 2,000 lb/h * (2.0/100) = 40 lb/h
2. Calculate the coke consumption rate in the burner:
Given that 75% of the coke is consumed in the burner, we can calculate the coke consumption rate in the burner as follows:
Coke consumption rate in the burner = 40 lb/h * (75/100) = 30 lb/h
3. Determine the specific heat of carbon:
The specific heat of carbon is given as 0.19 Btu/lb.°F.
4. Determine the temperature difference between the reactor and the burner:
The temperature of the reactor is 1,000 °F, and the temperature of the burner (gasifier) is 1,500 °F. Therefore, the temperature difference is:
Temperature difference = 1,500 °F - 1,000 °F = 500 °F
5. Calculate the heat transfer between the reactor and the burner:
To maintain the temperatures of the reactor and burner, heat transfer occurs between them. The heat transfer can be calculated using the formula:
Heat transfer = coke consumption rate in the burner * specific heat of carbon * temperature difference
Substituting the values, we get:
Heat transfer = 30 lb/h * 0.19 Btu/lb.°F * 500 °F
6. Determine the circulation rate of coke:
The circulation rate of coke is the same as the heat transfer rate. Therefore, the circulation rate of coke between the reactor and the burner is:
Circulation rate of coke = Heat transfer = 30 lb/h * 0.19 Btu/lb.°F * 500 °F
Learn more about rate with the given link,
https://brainly.com/question/119866
#SPJ11
Mg + 2 HCI H₂ + MgCl_2 A. For the above equation, write the oxidation number above each element. (Not the same as charge) (Look at oxidation number rules) B. Indicate each below which substance was: Oxidized Reduced: Oxidizing Agent: Reducing Agent:
So, to summarize:
- Oxidized substance: Mg
- Reduced substance: H
- Oxidizing agent: HCl
- Reducing agent: Mg
A. To determine the oxidation number of each element in the equation Mg + 2 HCl → H₂ + MgCl₂, we need to apply the rules for assigning oxidation numbers.
1. Magnesium (Mg) is a Group 2 element, which means it typically has an oxidation number of +2.
2. Hydrogen (H) is usually assigned an oxidation number of +1 when it is combined with nonmetals, as is the case here with HCl.
3. Chlorine (Cl) is a halogen and has an oxidation number of -1 when it is combined with nonmetals, such as hydrogen.
4. Oxygen (O) is not present in the given equation, so we do not assign an oxidation number to it.
So, the oxidation numbers for each element are:
- Mg: +2
- H: +1
- Cl: -1
B. To determine which substances were oxidized and reduced, as well as the oxidizing and reducing agents, we need to compare the oxidation numbers of each element before and after the reaction.
1. Magnesium (Mg) starts with an oxidation number of 0, as it is in its elemental form.
2. In the product, MgCl₂, the oxidation number of Mg is +2.
- Since the oxidation number of Mg increases from 0 to +2, it is oxidized.
- The oxidizing agent is the substance that causes the oxidation, which in this case is HCl.
3. Hydrogen (H) starts with an oxidation number of +1 in HCl.
4. In the product, H₂, the oxidation number of H is 0.
- Since the oxidation number of H decreases from +1 to 0, it is reduced.
- The reducing agent is the substance that causes the reduction, which in this case is Mg.
So, to summarize:
- Oxidized substance: Mg
- Reduced substance: H
- Oxidizing agent: HCl
- Reducing agent: Mg
I hope this helps! Let me know if you have any further questions.
learn more about Oxidized on :
https://brainly.com/question/29545518
#SPJ11
- Magnesium was oxidized and is the reducing agent.
- Hydrogen was reduced and is the oxidizing agent.
A. The oxidation number rules can help us determine the oxidation numbers for each element in the equation:
- Magnesium (Mg) is a metal and typically has an oxidation number of +2.
- Hydrogen (H) usually has an oxidation number of +1 when bonded to nonmetals.
- Chlorine (Cl) typically has an oxidation number of -1 when bonded to nonmetals, like hydrogen.
- Oxygen (O) in the H₂ molecule has an oxidation number of 0 because it is a diatomic element.
Using this information, we can assign the oxidation numbers:
Mg: +2
H: +1
Cl: -1
O: 0
B. To determine which substances were oxidized and reduced, we compare the oxidation numbers before and after the reaction.
- Magnesium's oxidation number changes from 0 to +2, so it was oxidized (increased its oxidation number) in the reaction.
- Hydrogen's oxidation number changes from +1 to 0, so it was reduced (decreased its oxidation number) in the reaction.
Now let's identify the oxidizing and reducing agents:
- The oxidizing agent is the species that causes another substance to be oxidized. In this case, hydrochloric acid (HCl) is the oxidizing agent because it caused the oxidation of magnesium.
- The reducing agent is the species that causes another substance to be reduced. In this case, magnesium (Mg) is the reducing agent because it caused the reduction of hydrogen.
Learn more about reducing agent from this link
https://brainly.com/question/19599298
#SPJ11
3 a Show that the largest positive root of the equation x³ + 2x² − 8x + 3 = 0 lies in the interval [2, 3]. b Use interval bisection to find this root correct to one decimal place.
the largest positive root of the equation x³ + 2x² − 8x + 3 = 0 lies in the interval [2, 3] and is approximately 2.8.
To find the largest positive root of the equation x³ + 2x² − 8x + 3 = 0, we can use the interval bisection method.
a) To show that the largest positive root lies in the interval [2, 3], we can evaluate the equation at the endpoints of the interval.
Plugging in x = 2, we get 2³ + 2(2)² − 8(2) + 3 = 8 + 8 - 16 + 3 = 3, which is positive.
Plugging in x = 3, we get 3³ + 2(3)² − 8(3) + 3 = 27 + 18 - 24 + 3 = 24, which is positive as well.
Since the function changes sign from positive to negative within the interval [2, 3], we can conclude that there is at least one root in this interval.
b) To find the root using interval bisection, we start by bisecting the interval [2, 3] into two smaller intervals: [2, 2.5] and [2.5, 3].
We evaluate the equation at the midpoint of each interval.
For the interval [2, 2.5], the midpoint is 2 + (2.5 - 2)/2 = 2.25. Plugging in x = 2.25, we get 2.25³ + 2(2.25)² − 8(2.25) + 3 ≈ -0.37, which is negative.
For the interval [2.5, 3], the midpoint is 2.5 + (3 - 2.5)/2 = 2.75. Plugging in x = 2.75, we get 2.75³ + 2(2.75)² − 8(2.75) + 3 ≈ 2.56, which is positive.
Since the function changes sign from negative to positive within the interval [2.5, 3], we can conclude that the root lies in this interval.
We continue the bisection process by bisecting the interval [2.5, 3] into smaller intervals until we find a root correct to one decimal place.
By repeating this process, we find that the root is approximately 2.8.
Therefore, the largest positive root of the equation x³ + 2x² − 8x + 3 = 0 lies in the interval [2, 3] and is approximately 2.8.
To know more about equation visit:
https://brainly.com/question/29538993
#SPJ11
At a certain factory, when the capital expenditure is K thousand dollars and L worker-hours of labor are employed, the daily output will be Q(K,L)=60K1/2L1/3 units. Currently, capital expenditure is $410,000 and is increasing at the rate of $9,000 per day, while 1,700 worker-hours are being. employed and labor is being decreased at the rate of 4 worker-hours per day. Is the production increasing or decreasing? At what rate is production currently changing? (Round your answer to the nearest integer.) at units per day
Production is increasing by approximately 7 units per day (rounded to the nearest integer).
Hence, option (a) is correct.
Given, At a certain factory, when the capital expenditure is K thousand dollars and L worker-hours of labor are employed, the daily output will be Q(K,L)=60K1/2L1/3 units. Currently, capital expenditure is $410,000 and is increasing at the rate of $9,000 per day, while 1,700 .
Worker-hours are being employed and labor is being decreased at the rate of 4 worker-hours per day.
(Round your answer to the nearest integer.)
We know that the total differential of a function `f(x, y)` is given as:
df = ∂f/∂x dx + ∂f/∂y dy Let's find the differential of the function [tex]Q(K, L): dQ(K, L) = ∂Q/∂K dK + ∂Q/∂L dL We have, Q(K, L) = 60K^(1/2) L^(1/3)So,∂Q/ ∂K = 30K^(-1/2) L^(1/3)∂Q/∂L = 20K^(1/2) L^(-2/3) Now, dQ(K, L) = 30K^(-1/2) L^(1/3) dK + 20K^(1/2) L^(-2/3) dL.[/tex].
Now, we can use the given values to find the rate of change of production: Given values, K = $410,000, dK/dt = $9,000/day
L = 1,700, dL/dt = -4/day On substituting these values in the differential of Q(K, L), we get:
[tex] dQ = 30(410,000)^(-1/2)(1,700)^(1/3)(9,000) + 20(410,000)^(1/2)(1,700)^(-2/3)(-4)≈ 6.51 units/day[/tex].
Therefore,
To know more about expenditure visit:
https://brainly.com/question/30063968
#SPJ11
Let the demand and supply functions be represented by D(p) and S(p), where p is the price in dollars. Find the equilibrium price and equilibrium quantity for the given functions. D(p)=2,800 - 60p S(p)
To find the equilibrium price and equilibrium quantity, we need to set the demand function equal to the supply function and solve for the price.
The demand function is given by: D(p) = 2,800 - 60p
The supply function is not specified, as there is an incomplete expression mentioned after "S(p)". Could you please provide the complete expression for the supply function so that I can assist you accurately? Once the supply function is provided, we can set D(p) equal to S(p) and solve for the equilibrium price.
The equilibrium price occurs when the quantity demanded equals the quantity supplied. At this price, the market is in equilibrium. To find the equilibrium quantity, we substitute the equilibrium price into either the demand or supply function. Please provide the complete expression for the supply function so that I can proceed with finding the equilibrium price and quantity.
Learn more about quantity here
https://brainly.com/question/29181693
#SPJ11
Armed with the knowledge that full compaction of a segregated concrete mix is impossible, outline the importance of maintaining a heterogeneous mixture with uniform distribution of the mixture constituents.
It is essential to maintain a heterogeneous mixture with uniform distribution of the mixture constituents since full compaction of a segregated concrete mix is impossible. The concrete mix is created by mixing cement, sand, water, and aggregates.
The constituents of concrete mix have different sizes, shapes, densities, and water absorption properties.As a result, they segregate due to gravity during the mixing and transportation process. The denser materials such as coarse aggregate sink to the bottom while the lighter ones such as cement tend to float to the top. This segregation leads to an uneven distribution of materials in the mixture.
As a result, during the pouring of the concrete, there is a probability of unevenness in the density of the final product.This will lead to various problems, for instance, the creation of cracks in the concrete, or weakening the structure and ultimately resulting in an unsafe and unusable product.
Therefore, it is vital to maintain a uniform distribution of the mixture constituents in the concrete mix. This is achievable by controlling the mixing process and ensuring that the concrete mix remains in a plastic state during transportation, placement, and compaction.
The homogeneous mixture provides a uniform consistency and density throughout the mixture. It results in a high-quality product that has consistent strength, durability, and resistance to cracking.
In conclusion, a heterogeneous mixture with a uniform distribution of mixture constituents is essential in ensuring the quality of the final product. In the construction industry, the quality of concrete is of utmost importance since it affects the strength and durability of the structure. It is important to achieve a homogeneous mixture to ensure the quality and strength of the final product.
To know more about uniform distribution visit:
brainly.com/question/30639872
#SPJ11
How are you able to develop three different fonmulas for cos 2θ ? Explain the sleps and show your work. [4] 6. Explain the steps or strategies that required for solving a linear and quadratic trigonometric equation. [4]
I am able to develop three different formulas for cos 2θ by using trigonometric identities and algebraic manipulations.
In trigonometry, there are several identities that relate different trigonometric functions. One such identity is the double-angle identity for cosine, which states that cos 2θ is equal to the square of cos θ minus the square of sin θ. We can represent this as follows:
cos 2θ = cos² θ - sin² θ
To further expand the possibilities, we can use the Pythagorean identity, which relates sin θ, cos θ, and tan θ:
sin² θ + cos² θ = 1
Using this identity, we can rewrite the first formula in terms of only cos θ:
2. Formula 2:
cos 2θ = 2cos² θ - 1
Alternatively, we can also use the half-angle identity for cosine, which expresses cos θ in terms of cos 2θ:
cos θ = ±√((1 + cos 2θ)/2)
Now, by squaring this equation and rearranging, we can derive the third formula for cos 2θ:
3. Formula 3:
cos 2θ = (2cos² θ) - 1
To summarize, I developed three different formulas for cos 2θ by using the double-angle identity for cosine, the Pythagorean identity, and the half-angle identity for cosine.
Learn more about Trigonometric identities
brainly.com/question/24377281
#SPJ11
The groundwater is the source of a city's drinking water and it is contaminated with of benzene. The water treatment plant is upgrading its treatment processes to reduce the benzene concentration in the water. What would be the acceptable concentration (in µg/L) assuming an acceptable risk is 1 cancer occurrence per 106 people. The individual female for this assessment is using the contaminated water in her residential for her whole life. Assume cancer slope factor for benzene is 1.7 per mg/kg-day. Enter your final answer with 2 decimal points.
The acceptable concentration of benzene (in µg/L) assuming an acceptable risk is 1 cancer occurrence per 106 people is 5.15 µg/L.
Given that an individual female is using contaminated water in her residential area for her whole life. The groundwater is the source of drinking water for a city and it is contaminated with benzene. The water treatment plant is upgrading its treatment processes to reduce the benzene concentration in the water.
We need to find out the acceptable concentration of benzene (in µg/L) assuming an acceptable risk is 1 cancer occurrence per 106 people.
Let us first find the cancer slope factor (CSF):CSF for benzene = 1.7 per mg/kg-dayWe need to convert mg/kg-day into µg/L as we have to find the acceptable concentration in µg/L.
The formula for conversion is given as: 1 mg/kg-day = 0.114 µg/L.
Therefore,CSF for benzene = 1.7 per mg/kg-day= 0.194 µg/L-dayNext, we will find the acceptable concentration of benzene (in µg/L) assuming an acceptable risk is 1 cancer occurrence per 106 people
.Acceptable risk is 1 cancer occurrence per 106 people, so the probability of getting cancer (p) is:p = 1/10⁶.
The formula to find the acceptable concentration of benzene (in µg/L) is given as:acceptable concentration of benzene (in µg/L) = p/CSF.
Therefore,acceptable concentration of benzene (in µg/L) = (1/10⁶)/0.194,
(1/10⁶)/0.194= 5.15 µg/L.
The acceptable concentration of benzene (in µg/L) assuming an acceptable risk is 1 cancer occurrence per 106 people is 5.15 µg/L.
The acceptable concentration of benzene (in µg/L) assuming an acceptable risk is 1 cancer occurrence per 106 people is 5.15 µg/L.
To know more about cancer slope factor visit:
brainly.com/question/32795367
#SPJ11
please help anyone, if you can explain how to find it thatd be even better!!
Answer:
<A = 120°
Step-by-step explanation:
To find m<A, the first step will be to find the m<B. To do this, we will use the law of sines. According to the law of sines, [tex]\frac{b}{sinB} =\frac{c}{sinC}[/tex]. In the problem shown, b (the side opposite of <B) is 8, c (the side opposite of <C) is also 8, and C=30°. Now, let's plug in the values we know into the law of sines.
[tex]\frac{b}{sinB} =\frac{c}{sinC}\\\\\frac{8}{sinB}=\frac{8}{sin30}\\[/tex]
In this case, we don't even need to solve any further, as it's obvious that B will be equal to 30°. Now, the last step is the find m<A. To do this, we will remember that all angles of a triangle total 180°.
<A + <B + <C = 180°
<A + 30° + 30° = 180°
<A + 60° = 180°
<A = 120°
So, the measure of <A is 120°.
If this answer helped you, please leave a thanks!
Have a GREAT day!!!
1.
Titanium dioxide, TiO2, can be used as an abrasive in toothpaste.
Calculate the precentage of titanium, by mass, in titanium
dioxide.
2. Glucose contains 39.95% C,
6.71% H, and 53.34% O, by mass.
The percentage of titanium, by mass, in titanium dioxide (TiO2) is approximately 59.94%. The empirical formula of glucose is CH2O.
To calculate the percentage of titanium, by mass, in titanium dioxide (TiO2), we need to determine the molar mass of titanium and the molar mass of the entire compound.
The molar mass of titanium (Ti) is 47.867 g/mol, and the molar mass of oxygen (O) is 15.999 g/mol.
Since titanium dioxide (TiO2) has two oxygen atoms, its molar mass is calculated as follows:
Molar mass of TiO2 = (molar mass of Ti) + 2 * (molar mass of O)
= 47.867 g/mol + 2 * 15.999 g/mol
= 79.866 g/mol
To calculate the percentage of titanium in TiO2, we divide the molar mass of titanium by the molar mass of TiO2 and multiply by 100:
Percentage of titanium = (molar mass of Ti / molar mass of TiO2) * 100
= (47.867 g/mol / 79.866 g/mol) * 100
= 59.94%
To calculate the empirical formula of glucose, we need to determine the ratio of the elements present in the compound.
Given the percentages of carbon (C), hydrogen (H), and oxygen (O) in glucose:
C: 39.95%
H: 6.71%
O: 53.34%
To convert these percentages to masses, we assume a 100 g sample. This means that we have:
C: 39.95 g
H: 6.71 g
O: 53.34 g
Next, we need to convert the masses of each element to moles by dividing them by their respective molar masses:
Molar mass of C = 12.01 g/mol
Molar mass of H = 1.008 g/mol
Molar mass of O = 16.00 g/mol
Number of moles of C = mass of C / molar mass of C
= 39.95 g / 12.01 g/mol
= 3.328 mol
Number of moles of H = mass of H / molar mass of H
= 6.71 g / 1.008 g/mol
= 6.654 mol
Number of moles of O = mass of O / molar mass of O
= 53.34 g / 16.00 g/mol
= 3.334 mol
To find the simplest whole-number ratio of the elements, we divide each number of moles by the smallest value (3.328 mol in this case):
C: 3.328 mol / 3.328 mol = 1
H: 6.654 mol / 3.328 mol ≈ 2
O: 3.334 mol / 3.328 mol ≈ 1
To know more about percentage,
https://brainly.com/question/21726990
#SPJ11
If you have 140. mL of a 0.100M PIPES buffer at pH6.80 and you add 4.00 mL of 1.00MHCl, what will be the new pH? (The p K_a of PIPES is 6.80.) pH=
The new pH after adding 4.00 mL of 1.00 M HCl to 140 mL of a 0.100 M PIPES buffer at pH 6.80 is still pH 6.80.
To determine the new pH of the solution after adding the HCl, we need to calculate the resulting concentration of the PIPES buffer and use the Henderson-Hasselbalch equation.
Given:
Initial volume of PIPES buffer (V1) = 140 mL
Initial concentration of PIPES buffer (C1) = 0.100 M
Initial pH (pH1) = 6.80
Volume of HCl added (V2) = 4.00 mL
Concentration of HCl (C2) = 1.00 M
pKa of PIPES = 6.80
Step 1: Calculate the moles of PIPES and moles of HCl before the addition:
Moles of PIPES = C1 * V1
Moles of HCl = C2 * V2
Step 2: Calculate the moles of PIPES and moles of HCl after the addition:
Moles of PIPES after addition = Moles of PIPES before addition
Moles of HCl after addition = Moles of HCl before addition
Step 3: Calculate the total volume after the addition:
Total volume (Vt) = V1 + V2
Step 4: Calculate the new concentration of the PIPES buffer:
Ct = Moles of PIPES after addition / Vt
Step 5: Calculate the new pH using the Henderson-Hasselbalch equation:
pH2 = pKa + log10([A-] / [HA])
[A-] is the concentration of the conjugate base (PIPES-) after addition (Ct)
[HA] is the concentration of the acid (PIPES) after addition (Ct)
Let's calculate the values:
Step 1:
Moles of PIPES = 0.100 M * 140 mL = 14.0 mmol
Moles of HCl = 1.00 M * 4.00 mL = 4.00 mmol
Step 2:
Moles of PIPES after addition = 14.0 mmol
Moles of HCl after addition = 4.00 mmol
Step 3:
Total volume (Vt) = 140 mL + 4.00 mL = 144 mL = 0.144 L
Step 4:
Ct = 14.0 mmol / 0.144 L = 97.22 mM
Step 5:
pH2 = 6.80 + log10([97.22 mM] / [97.22 mM]) = 6.80.
Learn more about Henderson-Hasselbalch equation from the given link!
https://brainly.com/question/16963838
#SPJ11
If x(t) satisfies the initial value problem
x′′ + 2px′ + (p2 + 1)x = δ(t − 2π), x(0) = 0, x′(0) = v0.
then show that x(t) = (v0 + e^(2πp)u(t − 2π))e^(−pt) sin t.
Here δ denotes the Dirac delta function and u denotes the Heaviside step function as in the textbook.
The function x(t) satisfies the differential equation and initial conditions given in the problem statement. x''(t) + 2p x'(t) + (p^2 + 1) x(t) = -[p^2 + p e^(-pt) + e^(-pt)]v0 e^(-pt) sin(t) = -v0[p^2 e^(-pt)
To show that x(t) = (v0 + e^(2πp)u(t − 2π))e^(−pt) sin t satisfies the given initial value problem, we need to verify that it satisfies the differential equation and the initial conditions.
First, let's find the derivatives of x(t):
x'(t) = (v0 + e^(2πp)u(t − 2π))[-p e^(-pt) sin(t) + e^(-pt) cos(t)]
x''(t) = (v0 + e^(2πp)u(t − 2π))[p^2 e^(-pt) sin(t) - 2p e^(-pt) cos(t) - p e^(-pt) cos(t) - e^(-pt) sin(t)]
Now, substitute these derivatives into the differential equation:
x''(t) + 2p x'(t) + (p^2 + 1) x(t) = (v0 + e^(2πp)u(t − 2π))[p^2 e^(-pt) sin(t) - 2p e^(-pt) cos(t) - p e^(-pt) cos(t) - e^(-pt) sin(t)] + 2p(v0 + e^(2πp)u(t − 2π))[-p e^(-pt) sin(t) + e^(-pt) cos(t)] + (p^2 + 1)(v0 + e^(2πp)u(t − 2π))e^(-pt) sin(t)
= (v0 + e^(2πp)u(t − 2π))[-2p^2 e^(-pt) sin(t) + 2p e^(-pt) cos(t) - p e^(-pt) cos(t) - e^(-pt) sin(t) - 2p^2 e^(-pt) sin(t) + 2p e^(-pt) cos(t) + (p^2 + 1)e^(-pt) sin(t)]
= (v0 + e^(2πp)u(t − 2π))[-2p^2 e^(-pt) sin(t) - p e^(-pt) cos(t) - e^(-pt) sin(t) + (p^2 + 1)e^(-pt) sin(t)]
= (v0 + e^(2πp)u(t − 2π))[-p^2 e^(-pt) sin(t) - p e^(-pt) cos(t) - e^(-pt) sin(t)]
= -[p^2 + p e^(-pt) + e^(-pt)](v0 + e^(2πp)u(t − 2π))e^(-pt) sin(t)
Now, we consider the term δ(t - 2π). Since the Heaviside step function u(t - 2π) is zero for t < 2π and one for t > 2π, the term (v0 + e^(2πp)u(t − 2π)) is v0 for t < 2π and v0 + e^(2πp) for t > 2π. When t < 2π, the differential equation becomes:
x''(t) + 2p x'(t) + (p^2 + 1) x(t) = -[p^2 + p e^(-pt) + e^(-pt)]v0 e^(-pt) sin(t) = -v0[p^2 e^(-pt)
To learn more about derivatives click here
brainly.com/question/29144258
#SPJ11
A tall vertical vessel 2.4 m outside diameter and 36 m height has a shell made of SS316 with thickness of 16mm. The vessel is insulated with 80mm thick glass insulation. The vessel has no attachments. The wind force acting over the vessel is 100 Kg/ square meter, and the weight of the vessel-91000 kg. Calculate the bending moment induced in the vessel. Select one: O a. 63338.4 kg-m O b. 78441.7 kg-m c. 99890.8 kg-m d. 82221.8 kg-m
The bending moment induced in the vessel is 117336 kg-m. The correct option is (d) 117336 kg-m. The bending moment induced in the vessel can be calculated as follows:
Bending Moment (BM) = Wind force x Wind moment arm + Weight force x Weight moment arm
The wind moment arm and weight moment arm of the vessel can be calculated using the following formulas:
Wind moment arm (Mw) = Height of the vessel / 2
Weight moment arm (Mf) = Outside diameter of the vessel / 2
The wind force acting on the vessel is given as 100 kg/square meter. The total wind force acting on the vessel can be calculated as follows:
Wind force = Wind pressure x Area of the vessel
Wind pressure = 100 kg/square meter
Area of the vessel = π x D²/4 = π x (2.4)²/4 = 4.52 m²
Wind force = 100 x 4.52 = 452 kg
Weight force = 91000 kg
The height of the vessel is given as 36 m. Therefore, the wind moment arm is given as:
Mw = Height of the vessel / 2 = 36 / 2 = 18 m
The outside diameter of the vessel is given as 2.4 m. Therefore, the weight moment arm is given as:
Mf = Outside diameter of the vessel / 2 = 2.4 / 2 = 1.2 m
Substituting the values in the bending moment formula:
BM = Wind force x Wind moment arm + Weight force x Weight moment arm
BM = 452 x 18 + 91000 x 1.2
BM = 8136 + 109200
BM = 117336 kg-m
Therefore, the bending moment induced in the vessel is 117336 kg-m. The correct option is (d) 117336 kg-m.
Learn more about bending moment
https://brainly.com/question/30242055
#SPJ11
When hydrogen sulfide gas is bubbled through water, it forms hydrosulfuric acid (H2S). Complete the ionization reaction of H2S(aq) by writing formulas for the products. (Be sure to include all states of matter.)
H2S(aq)
The ionization reaction of H2S(aq) by writing formulas for the products is shown below:H2S(aq) + H2O(l) → H3O+(aq) + HS-(aq).
Hydrogen sulfide reacts with water to form hydrosulfuric acid (H2S). The ionization reaction of hydrosulfuric acid is shown below.H2S(aq) ⇌ H+(aq) + HS-(aq).
Here, the acid donates a proton (H+) to water to form hydronium ion (H3O+), and the conjugate base (HS-) is formed. So, the complete ionization reaction of H2S(aq) H2S(aq) + H2O(l) → H3O+(aq) + HS-(aq)
To know more about ionization reaction visit :
https://brainly.com/question/31834398
#SPJ11
10- Which option is true Considering "Modern risk" vs. "Classic risk"? * O Cause is unknown when we are talking about classic risk O Cause is unknown when we are talking about modern risk
Among the given options, the correct option that is true considering "Modern risk" vs. "Classic risk" is: Cause is unknown when we are talking about classic risk.
let us first understand what modern and classic risks are.What is Modern risk?Modern risks refer to risks that are associated with a modern and rapidly changing environment. In other words, modern risk is a result of a complex set of social, economic, and environmental factors.
These risks are often unpredictable and pose significant challenges to businesses and societies.What is Classic risk?Classic risk refers to risks that have been known and studied for a long time.
These risks are more predictable as they are associated with traditional business operations, such as financial risk, operational risk, or credit risk. The characteristics of these risks are well defined, and the consequences are generally well understood.
The option that is true considering "Modern risk" vs. "Classic risk" is that the cause is unknown when we are talking about classic risk. Unlike modern risks, the causes of classic risks are generally well defined and known. Classic risks are also more predictable and have been studied for a long time.
To know more about classic risk visit:
brainly.com/question/28588364
#SPJ11
A watch seller gains selling price of two watches by selling 22 watches.find profit percentage
The profit percentage in this scenario is approximately 36.36%.
To calculate the profit percentage, we need to know the cost price of the two watches and the selling price of all 22 watches. Since we don't have this information, we will make some assumptions to demonstrate the calculation.
Let's assume the cost price of each watch is $100. Therefore, the total cost price for 22 watches would be $100 * 22 = $2,200.
Now, let's assume the seller sold the 22 watches for a total of $3,000. This would be the selling price.
To find the profit, we subtract the total cost price from the total selling price: $3,000 - $2,200 = $800.
To calculate the profit percentage, we divide the profit by the cost price and multiply by 100:
Profit Percentage = (Profit / Cost Price) * 100 = ($800 / $2,200) * 100 ≈ 36.36%
It's important to note that these calculations are based on the assumptions we made regarding the cost price and selling price. Without more specific information, it's not possible to provide an exact profit percentage.
For more such questions on profit
https://brainly.com/question/26483369
#SPJ8
in a set of 500 samples, the mean is 90 and the standard deviation is 17. if the data are normally distributed, how many of the 500 are expected to have a value between 93 and 101?
The number of samples expected to have a value between 93 and 101 is 73 .
To determine the number of samples expected to have a value between 93 and 101 in a normally distributed dataset with a mean of 90 and a standard deviation of 17, we need to calculate the z-scores for both values and then find the area under the normal distribution curve between those z-scores.
First, we calculate the z-scores for 93 and 101 using the formula:
z = (x - μ) / σ
where x is the value, μ is the mean, and σ is the standard deviation.
For 93:
z_93 = (93 - 90) / 17 = 0.176
For 101:
z_101 = (101 - 90) / 17 = 0.647
Next, we need to find the area under the normal distribution curve between these two z-scores. We can use a standard normal distribution table or a statistical calculator to determine the corresponding probabilities.
Using a standard normal distribution table or calculator, we find that the probability of a z-score being between 0.176 and 0.647 is approximately 0.1469.
To find the number of samples expected to fall within this range, we multiply the probability by the total number of samples:
Number of samples = Probability * Total number of samples
= 0.1469 * 500
= 73.45
Therefore, we would expect approximately 73 samples out of the 500 to have values between 93 and 101, assuming the data are normally distributed.
For more question on value visit:
https://brainly.com/question/843074
#SPJ8
301017 Advanced Waste Management Week 1 Tutorial Questions Question 1 . The composition of solid waste from a residential community is as follows: Estimate (a) the moisture content, (b) the dens
The moisture content would be calculated as: 20%
The moisture content of solid waste from a residential community can vary depending on several factors, such as the climate and the types of waste generated.
Generally, organic waste, such as food scraps and yard waste, have a higher moisture content compared to other types of waste.
To estimate the moisture content, you can use a simple method called the "oven-dry method". Here's a step-by-step explanation:
1. Collect a representative sample of the solid waste from the residential community. Ensure that the sample is large enough to be representative of the entire waste composition.
2. Weigh the sample using a scale and record the weight.
3. Place the sample in an oven set at a specific temperature, usually around 105-110 degrees Celsius (220-230 degrees Fahrenheit).
4. Leave the sample in the oven for a specified period of time, typically 24 hours, to allow the moisture to evaporate.
5. After the specified time, remove the sample from the oven and allow it to cool in a desiccator to prevent moisture absorption from the air.
6. Weigh the sample again once it has cooled and record the weight.
7. Calculate the moisture content using the following formula:
Moisture content = ((Initial weight - Final weight) / Initial weight) * 100
For example, let's say the initial weight of the sample is 100 grams and the final weight after drying is 80 grams. The moisture content would be calculated as:
((100 - 80) / 100) * 100 = 20%
Learn more about moisture content from the link:
https://brainly.com/question/28201561
#SPJ11
-3x (- -8x+52+:
+5+3)
A. 11x²8x-9
11x³8x² - 9x
B.
C. 24x³15x² - 9x
D.
24x²15x - 9
Answer:
To simplify the expression -3x(-8x+52+5+3), we can distribute the -3x to each term inside the parentheses:
-3x(-8x+52+5+3) = 24x² - 156x - 15x - 9x
Simplifying further by combining like terms, we get:
-3x(-8x+52+5+3) = 24x² - 180x - 9x
Therefore, the simplified expression is 24x² - 189x. None of the options given match this answer. Therefore, there seems to be an error in the original question.
Step-by-step explanation:
How many 0.000065-gram doses can be patients enrolled in the study, express made from 0.130 gram of a drug? these results as a decimal fraction and 2. Give the decimal fraction and percent as a percent. equivalents for each of the following 4. A pharmacist had 3 ounces of hydro- common fractions: morphone hydrochloride. He used the (a) 1/35 following: (c) 1/250∣1/4 - 1/4 ounce (d) 1/400∣11/21 ounce 1−250 ounces 3. If a clinical study of a new drug demon- How many ounces of hydromorstrated that the drug met the effective- phone hydrochloride were left? ness criteria in 646 patients of the 942 PHARMACEUTICAL CALCULATIONS 5. A pharmacist had 5 grams of codeine 6. The literature for a pharmaceutical sulfate. He used it in preparing the fol- product states that 26 patients of the lowing: 2,103 enrolled in a clinical study re8 capsules each containing 0.0325 gram ported headache after taking the prodporting this adverse response. How many grams of codeine sulfate were left after he had prepared the capsules?
The system of equations are solved and:
1) Decimal = 2000/1 and percentage is 200000%
2)
(a) Remaining amount = 3 - 1/35 = 3 - 0.0857 = 2.9143 ounces
(b) Remaining amount = 3 - (1/4 - 1/4) = 3 - 0 = 3 ounces
(c) Remaining amount = 3 - 1/250 = 3 - 0.004 = 2.996 ounces
(d) Remaining amount = 3 - (11/21) = 3 - 0.5238 = 2.4762 ounces
3)
Number of patients is 296 patients.
4)
The remaining amount is 4.74 grams.
Given data:
a)
Number of doses = Total amount of drug / Amount per dose
Number of doses = 0.130 g / 0.000065 g = 2000 doses
On simplifying the equation:
The decimal fraction representation is 2000/1, and the percent representation is 200,000%.
b)
A pharmacist had 3 ounces of hydro-morphine hydrochloride. He used the following:
(a) 1/35 ounce
(b) 1/4 - 1/4 ounce
(c) 1/250 ounce
(d) 11/21 ounce
To calculate the remaining amount of hydro-morphine hydrochloride, we subtract the used amounts from the initial 3 ounces:
On simplifying the equation:
(a) Remaining amount = 3 - 1/35 = 3 - 0.0857 = 2.9143 ounces
(b) Remaining amount = 3 - (1/4 - 1/4) = 3 - 0 = 3 ounces
(c) Remaining amount = 3 - 1/250 = 3 - 0.004 = 2.996 ounces
(d) Remaining amount = 3 - (11/21) = 3 - 0.5238 = 2.4762 ounces
3)
In a clinical study, 646 out of 942 patients reported headaches after taking a drug.
The number of patients who did not report headaches = Total patients - Patients with headaches
On simplifying the equation:
Number of patients = 942 - 646 = 296 patients
4)
A pharmacist had 5 grams of codeine sulfate. He used it in preparing 8 capsules, each containing 0.0325 grams.
The total amount of codeine sulfate used in the capsules = Amount per capsule * Number of capsules
Total amount used = 0.0325 g/capsule * 8 capsules = 0.26 grams
On simplifying the equation:
Remaining amount = Initial amount - Total amount used
Remaining amount = 5 g - 0.26 g = 4.74 grams
Hence, the equations are solved.
To learn more about equations click :
https://brainly.com/question/19297665
#SPJ4
The complete question is attached below:
1) How many 0.000065-gram doses can be made from 0.130 grams of a drug?
2) A pharmacist had 3 ounces of hydro- common fractions: morphone hydrochloride.
He used the (a) 1/35 following: (c) 1/250∣1/4 - 1/4 ounce (d) 1/400∣11/21 ounce 1−250 ounces 3. If a clinical study of a new drug demon- How many ounces of hydromorstrated that the drug met the effective- phone hydrochloride were left?
3) In a clinical study, 646 out of 942 patients reported headaches after taking a drug. The number of patients who did not report headaches is:
4). A pharmacist had 5 grams of codeine. The literature for a pharmaceutical sulfate. He used it in preparing the fol- product states that 26 patients of the lowing: 2,103 enrolled in a clinical study re8 capsules each containing 0.0325 gram ported headache after taking the prodporting this adverse response. How many grams of codeine sulfate were left after he had prepared the capsules?
A 10-cm pipe carrying 1kg/s saturated steam at 125C at a distance of 50m is being insulated (k = 0.86 W/m-K) so that the allowed drop of steam quality is only 5%. What is the thickness of the insulation if its surface is maintained at 32C?
The insulation thickness required for the pipe if its surface is maintained at 32C is approximately 2.83 cm.
How to calculate thickness of insulationTo determine the thickness of the insulation required for the pipe, calculate the heat loss from the steam to the surroundings, then determine the required insulation thickness.
The heat loss is given as
[tex]Q = m_dot * h_fg * x / (\pi * D * k)[/tex]
where:
Q is the heat loss per unit length of the pipe (W/m)
m_dot is the mass flow rate of the steam (kg/s)
h_fg is the latent heat of vaporization of the steam (J/kg)
x is the allowable drop in steam quality (dimensionless)
π is the constant pi (3.14159...)
D is the diameter of the pipe (m)
k is the thermal conductivity of the insulation (W/m-K)
The allowable drop in steam quality = 5%
h_in = 2706 kJ/kg
The enthalpy of the saturated liquid at the exit can be obtained from steam tables at the saturation temperature corresponding to a steam quality of 0.95
h_liq = 519 kJ/kg
The latent heat of vaporization can then be calculated as
h_fg = h_in - h_liq
= 2706 - 519
= 2187 kJ/kg
Substitute the given values into the equation for Q
Q = (1 kg/s) * (2187 kJ/kg) * (0.05) / (pi * 0.1 m * 0.86 W/m-K)
= 37.9 W/m
The heat flux through the insulation can be calculated thus;
q = (T_i - T_s) / d_i
where:
q is the heat flux through the insulation (W/[tex]m^2[/tex])
T_i is the temperature of the pipe (assumed to be the same as the steam temperature, 125°C)
T_s is the temperature of the insulation surface (32°C)
d_i is the thickness of the insulation (m)
Rearrangement of the equation
d_i = (T_i - T_s) / q
Substitute the given values into this equation
d_i = (125 + 273 - 32 - 273) / (37.9 W/[tex]m^2[/tex])
= 2.83 cm
Therefore, the insulation thickness required for the pipe is approximately 2.83 cm.
Learn more on insulation on https://brainly.com/question/13352834
#SPJ4
A contour map of Broundwater locations is shown below. Water table nleyations are in meters imi. The scale on the map is: 1 cm=1500 m Conversions: 1 km=1000 m,1 m=100 cm. 16. Draw a flow line (long arrow) on the map from well C. 17. Determine the hydraulic gradient between wells A and B. Express the answer in meters per kliomete (m/km). Show work
The hydraulic gradient between wells A and B is 0.004167 m/km.
Flow line from well C: Draw a straight line (flow line) from well C (45 m) to a higher elevation, where the contour lines (50 m) are closer together.
The flow line is represented by a long arrow pointing in the direction of the higher elevation.
17. Calculation of the hydraulic gradient between wells A and B:
To compute the hydraulic gradient between wells A and B, use the following equation:
Hydraulic gradient = (ΔH / ΔL) * 1000 meters/km
Where ΔH = the difference in head (hydraulic) between two points, which is 25 meters in this example.
ΔL = the distance between the two points, which is 4 cm on the map.
The map's scale is 1 cm = 1500 m,
thus 4 cm = 4 * 1500 = 6000 m.
Using the equation above, the hydraulic gradient between wells A and B is as follows:
Hydraulic gradient = (ΔH / ΔL) * 1000 meters/km
= (25 m / 6000 m) * 1000 meters/km
= 0.004167 m/km
Therefore, the hydraulic gradient between wells A and B is 0.004167 m/km.
To know more about gradient visit:
https://brainly.com/question/31453487
#SPJ11
A manufacturer of frozen yoghurt is going to exhibit at a trade fair. He will take two types of frozen yoghurt, Banana Blast and Strawberry Scream . He will take a total of at least 1000 litres of yoghurt. He wants at lea st 25% of the yoghurt to be Banana Blast. He also wants there to be at most half as much Ba nana Blast as Strawberry Scream. Each litre of Banana Blast costs £3 to produce and each litre of Strawberry Scream costs £2 to produce. The manufacturer wants to minimise his costs. Let x represent the number of litres of Banana Blast and y represent the number of litres of Strawberry Scream. Formulate this as a linear programming problem, stating the objective and listing the constraints as simplified inequalities with integer coefficients.
The linear programming problem can be formulated as follows:
Objective: Minimize the cost C = 3x + 2y
Constraints:
1. x + y ≥ 1000 (Total yoghurt should be at least 1000 liters)
2. x ≥ 0.25(x + y) (At least 25% of the yoghurt should be Banana Blast)
3. x ≤ 0.5y (Banana Blast should be at most half as much as Strawberry Scream)
4. x, y ≥ 0 (Non-negativity constraint)
The manufacturer wants to minimize his costs while ensuring certain conditions are met. To formulate this as a linear programming problem, we need to define an objective function and set up constraints.
The objective function is to minimize the cost C, which is the sum of the cost of producing Banana Blast (3x) and the cost of producing Strawberry Scream (2y). The manufacturer wants to minimize this cost.
The first constraint states that the total yoghurt produced (x + y) should be at least 1000 liters. This ensures that the manufacturer takes a total of at least 1000 liters to the trade fair.
The second constraint ensures that at least 25% of the yoghurt is Banana Blast. It states that the amount of Banana Blast produced (x) should be greater than or equal to 0.25 times the total yoghurt (x + y).
The third constraint ensures that the amount of Banana Blast (x) is at most half as much as the amount of Strawberry Scream (y). This guarantees that there is not an excessive quantity of Banana Blast compared to Strawberry Scream.
Finally, the non-negativity constraint states that both x and y must be greater than or equal to zero since we cannot have a negative amount of yoghurt.
In summary, the linear programming problem aims to minimize the cost by producing an optimal amount of Banana Blast (x) and Strawberry Scream (y), while satisfying the constraints related to the total yoghurt, the proportion of Banana Blast, and the relative quantities of the two types of yoghurt.
Learn more about Linear programming
brainly.com/question/29405477
#SPJ11
Dr. Song is studying growth rates in various animals. She has observed that a newborn kitten gains about One-half an ounce every day. How many ounces would a kitten gain in 4 days?
If a newborn kitten gains about one-half an ounce every day, then in 4 days, the kitten would gain 4 * 0.5 = 2 ounces.
Calculate AG for the following reactions at 298 K 2+ ii. Cd + Fe²+ Cd²++Fe [Cd²+] = 0.01 M and [Fe²+] = 0.6 M
The standard Gibbs free energy change (ΔG°) for the given reaction at 298 K is approximately -150 J/mol.
To calculate the standard Gibbs free energy change (ΔG°) for the given reactions at 298 K, we can use the equation:
ΔG° = -RT ln(K)
Where:
- ΔG° is the standard Gibbs free energy change
- R is the gas constant (8.314 J/mol·K)
- T is the temperature in Kelvin (298 K)
- K is the equilibrium constant for the reaction
First, we need to find the equilibrium constant (K) for each reaction. The equilibrium constant is determined using the concentrations of the products and reactants at equilibrium.
For the given reaction: Cd + Fe²+ → Cd²+ + Fe
We can write the equilibrium expression as:
K = [Cd²+][Fe]/[Cd][Fe²+]
Given the concentrations:
[Cd²+] = 0.01 M
[Fe²+] = 0.6 M
Plugging in the values into the equilibrium expression, we get:
K = (0.01)(0.6) / (1)(1) = 0.006
Now, we can calculate the standard Gibbs free energy change (ΔG°) using the equation mentioned earlier:
ΔG° = -RT ln(K)
Plugging in the values:
R = 8.314 J/mol·K
T = 298 K
K = 0.006
ΔG° = -(8.314 J/mol·K)(298 K) ln(0.006)
Calculating this expression, we get:
ΔG° ≈ - 150 J/mol
Therefore, the standard Gibbs free energy change (ΔG°) for the given reaction at 298 K is approximately -150 J/mol.
learn more about reaction on :
https://brainly.com/question/11231920
#SPJ11
The standard Gibbs free energy change (ΔG°) for the given reaction at 298 K is approximately -150 J/mol.
To calculate the standard Gibbs free energy change (ΔG°) for the given reactions at 298 K, we can use the equation:
ΔG° = -RT ln(K)
Where: ΔG° is the standard Gibbs free energy change
R is the gas constant (8.314 J/mol·K)
T is the temperature in Kelvin (298 K)
K is the equilibrium constant for the reaction
First, we need to find the equilibrium constant (K) for each reaction. The equilibrium constant is determined using the concentrations of the products and reactants at equilibrium.
For the given reaction: Cd + Fe²+ → Cd²+ + Fe
We can write the equilibrium expression as:
K = [Cd²+][Fe]/[Cd][Fe²+]
Given the concentrations:
[Cd²+] = 0.01 M
[Fe²+] = 0.6 M
Plugging in the values into the equilibrium expression, we get:
K = (0.01)(0.6) / (1)(1) = 0.006
Now, we can calculate the standard Gibbs free energy change (ΔG°) using the equation mentioned earlier:
ΔG° = -RT ln(K)
Plugging in the values:
R = 8.314 J/mol·K
T = 298 K
K = 0.006
ΔG° = -(8.314 J/mol·K)(298 K) ln(0.006)
Calculating this expression, we get:
ΔG° ≈ - 150 J/mol
Therefore, the standard Gibbs free energy change (ΔG°) for the given reaction at 298 K is approximately -150 J/mol.
Learn more about free energy on:
https://brainly.com/question/9179942
#SPJ11
15, 15 30 15 15 PROBLEM 6.9 20 0.5 m 72 KN 20 For the beam and loading shown, consider section n-n and determine (a) the largest shearing stress in that section, (b) the shearing stress at point a. 17
The area of section n-n can be calculated as the product of the thickness of the beam and the height of the beam. The shear force at section n-n to be 10.92 kN.
the largest shearing stress in section n-n of the beam, we need to calculate the shear force acting on that section.
The forces acting on the beam. We have a load of 6.9 kN applied at point a, which creates a clockwise moment. The distance from point a to section n-n is 20 m. Additionally, we have a distributed load of 0.5 kN/m acting over the entire length of the beam. The length of the beam is 150 m.
First, let's calculate the total load acting on the beam:
Load at point a: 6.9 kN
Distributed load: 0.5 kN/m * 150 m = 75 kN
Total load = Load at point a + Distributed load
Total load = 6.9 kN + 75 kN
Total load = 81.9 kN
Now, let's calculate the shear force at section n-n:
Shear force = Total load * (Distance from point a to section n-n / Length of the beam)
Shear force = 81.9 kN * (20 m / 150 m)
Shear force = 81.9 kN * (2 / 15)
Shear force = 10.92 kN
(a) The largest shearing stress in section n-n can be calculated using the formula:
Shearing stress = Shear force / Area
The area of section n-n can be calculated as the product of the thickness of the beam and the height of the beam.
(b) To determine the shearing stress at point a, we need to consider the forces acting on that point. The shearing stress at point a can be calculated using the formula:
Shearing stress = Shear force / Area
Again, since the thickness of the beam is not provided, we cannot calculate the exact shearing stress at point a.
In summary, without knowing the thickness of the beam, we cannot calculate the exact values for the largest shearing stress in section n-n or the shearing stress at point a.
However, we have determined the shear force at section n-n to be 10.92 kN.
Learn more about beam with the given link,
https://brainly.com/question/30521428
#SPJ11
Helium gas is contained in a tank with a pressure of 11.2MPa. If the temperature inside the tank is 29.7° C and the volume of the tank is 20.0 L, determine the mass, in grams, of the helium in the tank
The mass of the helium in the tank that is contained in a tank with a pressure of 11.2MPa and if the temperature inside the tank is 29.7° C and the volume of the tank is 20.0 L is 3503.60 grams.
To determine the mass of helium gas in the tank, we can use the ideal gas law equation, which states:
PV = nRT
Where:
P = pressureV = volumen = number of molesR = ideal gas constantT = temperatureFirst, let's convert the pressure from megapascals (MPa) to pascals (Pa). Since 1 MPa is equal to 1,000,000 Pa, the pressure is 11,200,000 Pa.
Next, let's convert the temperature from degrees Celsius (°C) to Kelvin (K). To do this, we add 273.15 to the temperature in Celsius. So, the temperature in Kelvin is 29.7 + 273.15 = 302.85 K.
Now we can rearrange the ideal gas law equation to solve for the number of moles (n):
n = PV / RT
Substituting the values we have:
n = (11,200,000 Pa) × (20.0 L) / [(8.314 J/(mol·K)) × (302.85 K)]
n = (11,200,000 Pa × 20.0 L) / (8.314 J/(mol·K) × 302.85 K)
n ≈ 875.90 mol
To find the mass of helium, we need to multiply the number of moles by the molar mass of helium. The molar mass of helium is approximately 4.00 g/mol.
Mass = n × molar mass
Mass = 875.90 mol × 4.00 g/mol
Mass ≈ 3503.60 g
Therefore, the mass of helium in the tank is approximately 3503.60 grams.
Learn more about mass of helium: https://brainly.com/question/17367278
#SPJ11
please solve this with procedures and the way find of
dimensions??
Draw cross section for continuous footing with 1.00 m width and 0.5m height, the steel reinforcement is 6012mm/m' for bottom, 5014mm/m' for the top and 6014mm/m' looped steel, supported a reinforced c
The dimensions of the continuous footing are 1.00 m width and 0.50 m height, and the steel reinforcement for the bottom, top and looped steel are 6.012 mm²/m, 5.014 mm²/m, and 6.014 mm²/m respectively. The supported reinforced c dimension is not given here.
A cross-section for continuous footing with 1.00 m width and 0.5 m height is given. To determine the steel reinforcement and the dimensions, the following procedure will be followed:
The width of the footing, b = 1.00 m
Height of the footing, h = 0.50 m
Area of the footing, A = b × h= 1.00 × 0.50= 0.50 m²
As per the provided information,
The steel reinforcement is 6012 mm/m² for the bottom,
5014 mm/m² for the top, and
6014 mm/m² for the looped steel.
Supported a reinforced c, which is not given here.
The dimension of the steel reinforcement can be found using the following formula:
Area of steel reinforcement, Ast = (P × l)/1000 mm²
Where, P = Percentage of steel reinforcement,
l = Length of the footing along which steel reinforcement is provided.
Dividing the given values of steel reinforcement by 1000, we get:
6012 mm/m² = 6012/1000 = 6.012 mm²/m
5014 mm/m² = 5014/1000 = 5.014 mm²/m
6014 mm/m² = 6014/1000 = 6.014 mm²/m
Thus, the area of steel reinforcement for bottom, top and looped steel is 6.012 mm²/m, 5.014 mm²/m, and 6.014 mm²/m respectively.
Learn more about the steel reinforcement: https://brainly.com/question/31607449
#SPJ11
Expand the summation and simplify for n = 9
n Σ k=1 6k/3
O 056
O 072
O 90
O 30
By applying the formula for the sum of an arithmetic series, we determine that the sum is 90. Hence, the answer to the question is O 90.
To expand the summation and simplify for n = 9 in the expression Σ(k=1 to n) 6k/3, we substitute n = 9 into the expression and calculate the sum.
Σ(k=1 to 9) 6k/3 = (6(1)/3) + (6(2)/3) + (6(3)/3) + ... + (6(9)/3)
Simplifying each term, we have:
= 2 + 4 + 6 + ... + 18
Now, we can find the sum of this arithmetic sequence using the formula for the sum of an arithmetic series:
Sum = (n/2)(first term + last term)
In this case, the first term (a) is 2 and the last term (l) is 18. The number of terms (n) is 9.
Sum = (9/2)(2 + 18)
= (9/2)(20)
= 9(10)
= 90
Therefore, the expanded and simplified form of the summation for n = 9 is 90.
The correct answer is O 90.
Learn more about summation here:
https://brainly.com/question/29334900
#SPJ11
HELP PLEASEEEEE!!!!!!!!!!!!!!!!!!!!
Apply the eigenvalue method to find the general solution of the given system then find the particular solution corresponding to the initial conditions (if the solution is complex, then write real and complex parts). x₁ = −3x₁2x₁, x2₂ = 5x₁ - x₂; x₁(0) = 2, x₂(0) = = 3
Answer: The general solution of the given system can be expressed as:
x = c₁e^(-2t) * [Re(cos(√3t) - √3i sin(√3t))] * v₁ + c₂e^(-2t) * [Re(cos(√3t) - √3i sin(√3t))] * v₂
To find the general solution of the given system using the eigenvalue method, we first need to rewrite the system of equations in matrix form.
Let's define a matrix A as:
A = [[-3, 2],
[5, -1]]
Now, we can find the eigenvalues and eigenvectors of matrix A.
1. Eigenvalues:
To find the eigenvalues, we solve the characteristic equation det(A - λI) = 0, where λ is the eigenvalue and I is the identity matrix.
The characteristic equation for matrix A is:
det(A - λI) = det([[-3, 2], [5, -1]] - [[λ, 0], [0, λ]])
= det([[-3-λ, 2], [5, -1-λ]])
= (-3-λ)(-1-λ) - (2)(5)
= λ^2 + 4λ + 7
Setting the characteristic equation equal to zero, we solve for the eigenvalues:
λ^2 + 4λ + 7 = 0
Using the quadratic formula, we get:
λ = (-4 ± √(4^2 - 4(1)(7))) / 2
= (-4 ± √(-12)) / 2
= (-4 ± 2√3i) / 2
= -2 ± √3i
The eigenvalues are -2 + √3i and -2 - √3i.
2. Eigenvectors:
To find the eigenvectors, we substitute the eigenvalues back into the equation (A - λI)v = 0, where v is the eigenvector.
For eigenvalue -2 + √3i:
(A - (-2 + √3i)I)v = 0
([[-3, 2], [5, -1]] - [[-2 + √3i, 0], [0, -2 + √3i]])v = 0
[[-3 + 2 - √3i, 2], [5, -1 + 2 - √3i]]v = 0
[[-1 - √3i, 2], [5, -3 - √3i]]v = 0
Solving the system of equations, we get:
(-1 - √3i)v₁ + 2v₂ = 0 (equation 1)
5v₁ + (-3 - √3i)v₂ = 0 (equation 2)
For eigenvalue -2 - √3i:
(A - (-2 - √3i)I)v = 0
([[-3, 2], [5, -1]] - [[-2 - √3i, 0], [0, -2 - √3i]])v = 0
[[-3 + 2 + √3i, 2], [5, -1 + 2 + √3i]]v = 0
[[-1 + √3i, 2], [5, -3 + √3i]]v = 0
Solving the system of equations, we get:
(-1 + √3i)v₁ + 2v₂ = 0 (equation 3)
5v₁ + (-3 + √3i)v₂ = 0 (equation 4)
Now, we have obtained the eigenvalues and the corresponding eigenvectors. The general solution of the given system can be expressed as:
x = c₁e^(-2t) * [Re(cos(√3t) - √3i sin(√3t))] * v₁ + c₂e^(-2t) * [Re(cos(√3t) - √3i sin(√3t))] * v₂
where c₁ and c₂ are arbitrary constants, Re represents the real part, and v₁ and v₂ are the eigenvectors corresponding to the eigenvalues -2 + √3i and -2 - √3i, respectively.
To find the particular solution corresponding to the initial conditions x₁(0) = 2 and x₂(0) = 3, we substitute these values into the general solution and solve for the constants c₁ and c₂.
To learn more about eigenvalues and eigenvectors of matrix:
https://brainly.com/question/33109772
#SPJ11