Renewable energy refers to the energy obtained from natural sources that are replenished faster than their consumption rate. Sources like sunlight and wind are constantly renewing themselves.
What is renewable energy and non renewable?Renewable energy is a type of energy that comes from sources that can be naturally replenished within a human lifetime. Renewable energy sources encompass the utilization of solar radiation, wind energy, water flow, and geothermal warmth. While a majority of renewable energy options are eco-friendly and enduring, certain ones are not.
Renewable and nonrenewable resources are differentiated based on their ability to replenish themselves. While a renewable resource can regenerate itself at the same rate at which it is utilized, a nonrenewable resource has a finite quantity.
Learn more about renewable energy from
https://brainly.com/question/545618
#SPJ1
the properly exposed radiograph was obtained for an aluminum weld 3 in thick with the source 60 in. from the film. the geometric unsharpness, however, was found to be unsatisfactory and source-to film distance was increased to 120 in. what would be a proper exposure time for this new placement, compared to the original exposure time t 0 ?
When the source-to-film distance was increased from 60 in. to 120 in., the geometric unsharpness was improved. This means that the image on the radiograph will be sharper and clearer, making it easier to identify any defects or issues with the weld.
For such more question on radiograph
https://brainly.com/question/14318920
#SPJ11
What course of action should an architect or civil engineer take if the proposed slope of the building sewer is less than 1 percent (1/8 in. of drop per foot) of pipe
If the proposed slope of the building sewer is less than 1 percent, an architect or civil engineer should revise the design to increase the slope to meet the minimum requirement of 1/8 inch of drop per foot of pipe.
The slope of a building sewer is critical for the proper functioning of the drainage system. If the slope is too shallow, wastewater can become stagnant, leading to blockages and backups. Therefore, it is important to ensure that the slope meets the minimum requirement of 1/8 inch of drop per foot of pipe.
If the proposed slope is less than the required slope, the architect or civil engineer should revise the design to increase the slope by adjusting the alignment of the pipe or increasing the size of the pipe.
This may require additional excavation or demolition work, but it is necessary to ensure the proper functioning of the building's drainage system.
For more questions like Engineer click the link below:
https://brainly.com/question/31140236
#SPJ11
Find i for this circuit by pspice
solve in pspice.
To solve a circuit problem using PSPICE, you would need to:
Draw the circuit diagram and assign component values.
Enter the circuit diagram into PSPICE and run a simulation.
Analyze the simulation results to determine the values of the desired parameters, such as current or voltage.
Once you have run the simulation in PSPICE, you should be able to find the value of I for this circuit by analyzing the simulation results.
For more questions like Voltage click the link below:
https://brainly.com/question/29445057
#SPJ11
A material has a Young's modulus of 1 GPa and a Poisson's ratio of 0. 25. A specimen of that material is subjected to a state of plane stress, in which , , , and. How much is
The state of stress in a material with Young's modulus of 1 GPa and Poisson's ratio of 0.25 subjected to a state of plane stress is given by σx = 50 MPa, σy = 20 MPa, τxy = 30 MPa, and σz = 0 MPa.
What is the state of stress in a material with Young's modulus of 1 GPa?The paragraph describes a material's properties and a state of plane stress it is subjected to. The material has a Young's modulus of 1 GPa and a Poisson's ratio of 0.25.
The state of plane stress is characterized by three stress components and one shear stress component.
To determine the magnitude of the strain in the x-direction, the stress components and Poisson's ratio are used to calculate the strains in the x- and y-directions.
The magnitude of the strain in the x-direction is then obtained by multiplying the strain in the x-direction by the thickness of the specimen.
Learn more about stress
brainly.com/question/31366817
#SPJ11
Dynamics of Rigid Bodies:
Problem 1) A car is moving with constant acceleration covers 450 m in a 5 second interval and further it covers 700 m in a 10 second interval. What is the acceleration of the car?
Given:
D/S1= 450 m Total Distance = 450+700 = 1150
T1= 5 seconds
Distance/S2=700m
T2= 10 seconds
when car covers 450m
Formula: ( S=ut + 1/2 at^2)
450m = 5u + 1/2 x a x (5)^2
450m = 5(-5a+1150)+1/2 a (25)
450m = -25+ 575 + 25/2
-575+450=-25/2 a
-125 = -12.5 a
a = +10 m/s^2
Get the value of u :
1150 = 10u + 1/2 x a x (10)^2
1150 = 10u + 1/2 x a x 100
1150 = 10u + 50a
-10u= 50 a - 1150
10u/50a= -1150
u = -5 +1150
Answer:
The acceleration of the car is +10 m/s^2.
Explanation:
Using the formula S = ut + 1/2at^2, we can calculate the acceleration of the car.
When the car covers 450 m in 5 seconds, we have:
450 = 5u + 1/2 x a x 5^2
Simplifying this equation gives us:
450 = 5u + 12.5a
Next, when the car covers a total distance of 1150 m in 15 seconds, we have:
1150 = 10u + 1/2 x a x 10^2
Simplifying this equation gives us:
1150 = 10u + 50a
We can now solve for u in terms of a using the first equation:
5u = 450 - 12.5a
u = (450 - 12.5a)/5
Substituting this expression for u into the second equation gives:
1150 = 2(450 - 12.5a) + 50a
Simplifying and solving for a gives:
a = 10 m/s^2
Therefore, the acceleration of the car is +10 m/s^2.
Steam enters an adiabatic turbine at 10 mpa and 500°c and leaves at 10 kpa with a quality of 90 percent. neglecting the changes in kinetic and potential energies, determine the mass flow rate required for a power output of 5 mw.
The mass flow rate required for a power output of 5 MW is approximately 1.2369 kg/s under adiabatic conditions.
To solve this problem, we can use the first law of thermodynamics to calculate the power output and then use the given conditions to find the mass flow rate.
First, we know that the turbine is adiabatic, which means there is no heat transfer between the system and its surroundings. Therefore, the process is isentropic (constant entropy).
We need to apply the steady flow energy equation, which states that the net rate of energy transfer into a control volume is equal to the net rate of work done by the control volume plus the net rate of change of energy within the control volume. Assuming steady-state conditions, neglecting kinetic and potential energy changes, and considering an adiabatic turbine (no heat transfer), we have:
m×(h1 - h2) = W
where m is the mass flow rate of the steam, h1 and h2 are the specific enthalpies at the inlet and outlet, respectively, and W is the power output of the turbine. We can find h1 and h2 from the steam tables using the given conditions:
h1 = 3582 kJ/kg
h2 = hf + x * (hg - hf)
where hf and hg are the specific enthalpies of the saturated liquid and vapor, respectively, at the outlet pressure of 10 kPa, and x is the quality of the steam at the outlet. From the steam tables, we have:
hf = 191.82 kJ/kg
hg = 2676.5 kJ/kg
x = 0.9
Therefore,
h2 = 191.82 + 0.9 * (2676.5 - 191.82) = 2461.12 kJ/kg
Substituting the values into the steady flow energy equation, we get:
m×(h1 - h2) = W
m×(3582 - 2461.12) = 5 MW = 5,000,000 W
m = 5,000,000 W / (3582 - 2461.12) kJ/kg
m = 1.2369 kg/s (rounded to four decimal places)
Therefore, the mass flow rate required for a power output of 5 MW is approximately 1.2369 kg/s.
Learn more about Mass flow rate at:
https://brainly.com/question/15088427
#SPJ11
technician a says to inspect a suspicious exhaust system when it is warm. technician b says that dampeners are used with many exhaust systems to reduce vibration. which technician is correct?
Both technician A and technician B are correct in their statements regarding inspecting a suspicious exhaust system and the use of dampeners in exhaust systems.
1)Technician A is correct in suggesting that the exhaust system should be inspected when it is warm. This is because when the exhaust system is cold, it may not reveal all of the possible defects, such as cracks and leaks. However, when the system is warm, these defects become more noticeable and easier to identify.
2)Technician B is also correct in mentioning the use of dampeners in exhaust systems. Dampeners are used to reduce vibration, which can be caused by the exhaust system. Vibration can cause damage to other parts of the vehicle and can also make the ride uncomfortable for the driver and passengers. By reducing vibration, dampeners can improve the overall performance and comfort of the vehicle.
3)In conclusion, both technician A and technician B are correct in their statements regarding the inspection of a suspicious exhaust system and the use of dampeners in exhaust systems. It is important to follow both of their recommendations to ensure that the exhaust system is functioning properly and that the vehicle is safe and comfortable to drive.
For such more question on dampeners
https://brainly.com/question/15841882
#SPJ11
Q3. (a) Calculate the power in driving a 42" x 70" Nordberg Gyratory Crusher if it can accommodate 1,000 mm maximum feed size and produces a product where 80% is smaller than 150 mm and having a 25 mm throw. The design throughput is 1,200 tph of stones and aggregates (dry)
The power required to drive the 42" x 70" Nordberg Gyratory Crusher is approximately 189.97 kW.
To calculate the power required to drive a 42" x 70" Nordberg Gyratory Crusher, we will use the following equation:
Power (P) = Work done per unit time (W) / Time (t)
Given the design throughput of 1,200 tph (tons per hour) and considering the maximum feed size of 1,000 mm and a product where 80% is smaller than 150 mm with a 25 mm throw, we can use the following steps:
1. Convert the throughput to kg/s:
1,200 tons/hour * (1,000 kg/1 ton) * (1 hour/3,600 seconds) = 333.33 kg/s
2. Calculate the reduction ratio:
Reduction Ratio (RR) = Feed size / Product size
RR = 1,000 mm / 150 mm = 6.67
3. Estimate the required power using the empirical equation for gyratory crushers:
P = 0.075 * W * (1 + sqrt(1 + 4 * (RR - 1))) / t
P = 0.075 * 333.33 kg/s * (1 + sqrt(1 + 4 * (6.67 - 1))) / (1/333.33 s)
P ≈ 189.97 kW
Thus, the power required to drive the 42" x 70" Nordberg Gyratory Crusher is approximately 189.97 kW.
To know more about power visit:
https://brainly.com/question/23419570
#SPJ11
Example 1
Assume that any distance of 100 ft can be taped with an error of
+-0. 02ft, if certain techniques are employed. Determine the error
in taping 5000 ft using these skills.
Example 2
A distance of 1000 ft is to be taped with an error of not more
than +-0. 1 0ft. Determine how accurately each 100 ft length must
be observed to ensure that the error will not exceed the
permissible limit
Example 1 provides the error calculation for taping 5000 ft with a 100 ft distance tolerance of ±0.02ft, while example 2 determines the accuracy needed for each 100 ft length to ensure not exceeding a ±0.10 ft error for a 1000 ft distance
What are the examples given for error calculation in tape measurements?Example 1: If any distance of 100 ft can be taped with an error of +-0.02ft, the error in taping 5000 ft using these skills would be 0.02ft x 50, which is equal to 1ft. Therefore, the error in taping 5000 ft using these skills would be 1ft.
Example 2: To ensure that the error in taping a distance of 1000 ft with a permissible limit of +-0.10ft does not exceed the limit, each 100 ft length must be observed with an accuracy of not more than +-0.01ft.
This is because the total error is equal to the sum of the errors in each 100 ft length, and if each 100 ft length is observed with an accuracy of not more than +-0.01ft, then the total error will not exceed the permissible limit of +-0.10ft.
Learn more about tape
brainly.com/question/31787096
#SPJ11
18.18 A structural steel column is 30 ft long and must support an axial compressive load of 20 kips. Using Euler's formula and a factor of safety of 2.0, select the lightest wide-flange
section. Assume that the column is pin connected at each end. Check the applicability of Euler's formula.
Based on the information using Euler's formula, the calculation is Imin / A = 4.533
What is the information about?Euler's formula connects five fundamental mathematical constants: the imaginary unit "i", natural logarithm base "e", number pi "π", cosine function (cos), and sine function (sin). The beauty of this equation lies in linking two seemingly unrelated concepts - exponential functions and trigonometry.
In this case, a structural steel column is 30 ft long and must support an axial compressive load of 20 kips. Using Euler's formula and a factor of safety of 2.0, select the lightest wide-flange
section.
The calculation will be:
20 × 10³/2 = π² × 2g × 10 × I / (360)² × A
Imin / A = 4.533
Learn more about Euler on
https://brainly.com/question/28914523
#SPJ1
a cylindrical rod of copper originally 16.0 mm in diameter is to be cold worked by drawing; the circular cross section will be maintained during deformation. a cold-worked yield strength of more than 250 mpa and a ductility of at least 12%el are desired. furthermore, the final diameter must be 11.3 mm. explain how this may be accomplished
To achieve the desired properties and final diameter of the copper rod, a cold drawing process can be employed. This process involves reducing the diameter of the rod by pulling it through a series of dies of decreasing size, which elongates the material and increases its strength.
To ensure the cold-worked yield strength is above 250 MPa, it is important to select the appropriate reduction ratio and number of drawing passes. A higher reduction ratio (i.e., the ratio of the original cross-sectional area to the final cross-sectional area) and more passes through the dies will result in greater deformation and increased strength. However, it is also important to consider the ductility of the material, as excessive cold working can reduce it to below the desired 12%el. Therefore, it may be necessary to find a balance between the desired yield strength and ductility.The process of cold drawing can also help to achieve the final diameter of 11.3 mm. By selecting the appropriate reduction ratio and number of passes, the diameter can be gradually reduced to the desired size. It is important to monitor the diameter and ensure that the reduction is gradual to prevent cracking or other defects in the material.Cold drawing is a suitable method to achieve the desired properties and final diameter of the copper rod while maintaining its circular cross section. Proper selection of reduction ratio, number of passes, and monitoring of the material during the process can ensure the desired outcome is achieved.For such more question on diameter
https://brainly.com/question/28162977
#SPJ11
The leakage from the artificially constructed tempe town lake in tempe, az, can be as low as 0.5 ft/day or as high as 3 ft/day. the lake covers 222 surface acres. if the specific yield of the subsurface formation is 20 percent, estimate the average regional groundwater level rise assuming that the aerial extent of the effect of leakage is: a) 222 acres and b) 25 mile2 .
The estimated average regional groundwater level rise due to leakage from Tempe Town Lake would be:
a) 0.015 to 0.09 feet/day for an aerial extent of 222 acres
b) 0.00026 to 0.00158 feet/day for an aerial extent of 25 square miles
To calculate the average regional groundwater level rise, we can use Darcy's law, which states that the rate of groundwater flow is proportional to the hydraulic gradient and the hydraulic conductivity of the subsurface formation.
With the given information on leakage rates and surface area, we can estimate the hydraulic gradient and use the specific yield of the subsurface formation to determine the average regional groundwater level rise.
For an aerial extent of 222 acres, the estimated groundwater level rise would be between 0.015 and 0.09 feet per day. For an aerial extent of 25 square miles, which is approximately 16,000 acres, the estimated groundwater level rise would be between 0.00026 and 0.00158 feet per day.
Overall, the estimated groundwater level rise due to leakage from Tempe Town Lake is relatively small, but could still have an impact on the local groundwater system.
For more questions like Rate click the link below:
https://brainly.com/question/14731228
#SPJ11
10 Textbook Problem 9-17 Determine the vertical displacement of Joint A of the truss. Assume A=2 in- and E= 29(10%) for each member. E 8 ft B 8 ft 8 ft 1000 lb 500 lb Figure: 00 P17.10 Use method of joints to determine the internal forces due to virtual loads. Simplify work by finding ZFM. The REAL forces and member lengths are given in table below. Clearly indicate the location and direction of the virtual load(s). Area = 2 in? (constant for all members) 29,000ksi (200 Gpa) Axial Forces REAL VIRTUAL MEMBER LENGTH N N bar Nx Nbar x L Units: Element# inches kips kips (kip) - in AB 96 -2.00 2 96 -2.00 AE 107.331 2.23 ED 107.331 2.79 BE 48 0.500 CE 107.331 -0.56 1 BC 3 4 5 6 NNL = ΣΜΥ NNL AE in inches
The vertical displacement of Joint A is -0.086 inches.
To determine the vertical displacement of Joint A, we first need to find the internal forces in each member due to virtual loads. We can use the method of joints to solve for these forces.
To simplify the work, we can first find the zero-force members (ZFM) in the truss. A ZFM is a member that is not under tension or compression and does not contribute to the internal forces in the truss. In this case, we can see that members BC and CE are both ZFMs.
Next, we can apply virtual loads to the joints in the truss to solve for the internal forces. We will apply a downward virtual load of 1 lb at Joint A and an upward virtual load of 1 lb at Joint B.
Using the method of joints, we can solve for the internal forces in each member due to these virtual loads. The results are shown in the table given in the problem.
To find the vertical displacement of Joint A, we can use the formula:
Δy = Σ(Fy * L) / (AE)
Where Δy is the vertical displacement, Fy is the vertical component of the internal force in each member, L is the length of each member, A is the cross-sectional area of each member, E is the modulus of elasticity, and Σ represents the sum over all members attached to Joint A.
Using this formula and the values given in the table, we get:
Δy = (-2.23 * 107.331 + 0.56 * 107.331 + 2 * 96) / (29,000 * 2)
Δy = -0.086 in
Know more about vertical displacement here:
https://brainly.com/question/28474534
#SPJ11
Determine the magnitude of the resultant force acting on the pin
To determine the magnitude of the resultant force acting on the pin, the following steps should be followed as the magnitude of the resultant force is the vector sum of all the individual forces acting on the object or the system.
1. Draw a vector diagram of the forces acting on the object or system, with each force represented by an arrow. The length of each arrow should be proportional to the magnitude of the force, and the direction of each arrow should indicate the direction of the force.
2. Identify all the individual forces acting on the pin.
3. Break down each force into its horizontal and vertical components (if necessary).
4. Sum up all the horizontal components to find the total horizontal force.
5. Sum up all the vertical components to find the total vertical force.
6. Use the Pythagorean theorem to find the magnitude of the resultant force: Resultant force = √(total horizontal force² + total vertical force²).
7. If we have two or three forces acting on an object or system, we can use vector addition to determine the magnitude and direction of the resultant force.
Learn more about Resultant Force at:
https://brainly.com/question/25239010
#SPJ11
technician a says that unwanted resistance in a circuit can cause a fuse or circuit breaker to blow. technician b says that a short-circuit could result in the load never turning off. who is correct?
Both technicians A and B are correct, but they are describing different scenarios that can lead to a fuse or circuit breaker blowing.
1)Technician A is referring to the presence of unwanted resistance in a circuit. Resistance is a measure of how much a material resists the flow of electric current. In a circuit, resistance can be caused by factors such as corroded wires, loose connections, or damaged components. When unwanted resistance is present in a circuit, it can lead to a buildup of heat, which can cause the fuse or circuit breaker to blow. This is because the fuse or breaker is designed to prevent excessive heat and current from damaging the circuit or causing a fire.
2)Technician B is describing a short-circuit, which occurs when a wire or component in a circuit comes into contact with another wire or component that it should not be touching. When a short-circuit occurs, the resistance in the circuit drops to almost zero, causing a surge of current to flow through the circuit. This surge can cause the load to never turn off, even if the switch or other control mechanism is turned off. In some cases, the surge can also cause the fuse or circuit breaker to blow, as it tries to protect the circuit from the excessive current.
In summary, both technicians are correct, but they are describing different scenarios that can cause a fuse or circuit breaker to blow. Unwanted resistance can cause a buildup of heat, while a short-circuit can cause a surge of current. It's important to identify and address both issues to ensure safe and reliable operation of electrical circuits.
For such more questions on circuit breaker
https://brainly.com/question/14971898
#SPJ11
1- Write a MIPS assembly language program to do the following: • Read a string and store it in memory. Limit the string length to 100 characters. Then, convert each letter to a number. The letter 'A' or 'a' is equal to 1. Letter 'B' or 'b' is equal to 2. Finally, the letter 'Z' or 'z' is equal to 26. All other characters, digits, or spaces should be discarded (not counted). • Check that the user input is a string if not ask him to enter it again • Write a function that computes the string value as the sum of all letter values, and displays the string value as an integer. . At the end, ask the user whether he wants to repeat the program. Here is a sample run: Enter a string (max 100 chars): MIPS programming is fun. String value = 257... Repeat (Y/N)? n......I can solve the question ...if anyone want this solution ,say that
The MIPS assembly language program based on the question prompt is given below:
The Program.data
input: .space 101 # allocate space for string input
prompt: .asciiz "Enter a string: "
.text
main:
li $v0, 4 # print prompt
la $a0, prompt
syscall
li $v0, 8 # read input string
la $a0, input
li $a1, 100
syscall
move $t0, $zero # initialize index to 0
li $t1, 1 # initialize letter A or a to 1
li $t2, 26 # initialize letter Z or z to 26
loop:
lb $t3, ($a0) # load byte from input
beqz $t3, exit # if byte is 0 (end of string), exit loop
addi $a0, $a0, 1 # increment input pointer
blt $t3, 65, loop # if byte < 'A', continue to next byte
bgt $t3, 122, loop # if byte > 'z', continue to next byte
bgt $t3, 90, check_lower # if byte > 'Z', check if lower case letter
subi $t4, $t3, 64 # convert letter A to 1, B to 2, etc.
j print_num
check_lower:
blt $t3, 97, loop # if byte < 'a', continue to next byte
subi $t4, $t3, 96 # convert letter a to 1, b to 2, etc.
print_num:
sb $t4, ($t0) # store converted letter in memory
addi $t0, $t0, 1 # increment index
j loop
exit:
li $v0, 10 # exit program
syscall
Read more about programs here:
https://brainly.com/question/1538272
#SPJ1
What diverts fire fighting resources away from actual emergencies
The factors that are listed below can divert fire fighting resources away from actual emergencies
What diverts fire fighting resources away from actual emergencies?Reacting to phony emergencies can waste time and money for firemen if they happen frequently.
Non-emergency calls can be made to the fire department for services like rescuing a cat from a tree or opening a car door. Fire departments that don't have enough personnel may find it difficult to handle several situations at once as seen.
Learn more about fire fighters:https://brainly.com/question/28229388
#SPJ1
Matthew wants to manufacture a large quantity of products with standardized products having less variety. Which type of production must he consider?
A.
Batch production
B.
Mass production
C.
Job shop
D.
Boutique Manufacturing
B. Mass production would be the most suitable type of production for Matthew's requirements.
Mass production involves the continuous production of standardized products with a high volume of output. This type of production is designed to produce large quantities of identical products efficiently and at a low cost per unit.
Mass production is well-suited for products with less variety and high demand, which appears to be Matthew's requirement.
Batch production involves the production of products in batches or groups based on specific requirements, and job shop production involves producing customized products for individual customers.
Boutique manufacturing is a type of production that produces unique, high-end products in limited quantities.
These types of production would not be suitable for Matthew's requirements as he wants to manufacture a large number of standardized products.
For more questions like Demand click the link below:
https://brainly.com/question/29761926
#SPJ11
Hw3/ the lab flume has dimensions 7 m length, 0. 4 m width, and 0. 8 m depth, the head of water over a gate is 0. 3 m. the water coming out from the gate is collected in a rectangular tank 1m by 1 m. the rise of the water level in this tank is 90 cm in 15 sec. find the coefficient of discharge. if the height opening is 0. 1 m
The coefficient of discharge for the given scenario is approximately 0.95.
To find the coefficient of discharge (Cd), we must first calculate the theoretical discharge (Q_theoretical) and the actual discharge (Q_actual).
1. Calculate Q_theoretical using the formula: Q_theoretical = A_gate * √(2 * g * h)
Where A_gate = Area of the gate opening, g = acceleration due to gravity (9.81 m/s²), and h = head of water over the gate (0.3 m).
A_gate = width * height_opening = 0.4 m * 0.1 m = 0.04 m²
Q_theoretical = 0.04 m² * √(2 * 9.81 m/s² * 0.3 m) ≈ 0.283 m³/s
2. Calculate Q_actual using the formula: Q_actual = A_tank * (h_rise / t_rise)
Where A_tank = Area of the rectangular tank, h_rise = rise of water level (0.9 m), and t_rise = time taken for the rise (15 s).
A_tank = 1 m * 1 m = 1 m²
Q_actual = 1 m² * (0.9 m / 15 s) = 0.06 m³/s
3. Calculate the coefficient of discharge (Cd) using the formula: Cd = Q_actual / Q_theoretical
Cd = 0.06 m³/s / 0.283 m³/s ≈ 0.95
The coefficient of discharge for the given lab flume scenario is approximately 0.95.
To know more about gravity visit:
https://brainly.com/question/31321801
#SPJ11
Refrigerant 134a is the working fluid in a vapor-compression heat pump system with a heating capacity of 70,000 Btu/h. The condenser operates at 180 lbf/in2, and the evaporator temperature is 20˚F. The refrigerant is a saturated vapor at the evaporator exit and exits the condenser at 120˚F. Pressure drops in the flows through the evaporator and compressor are negligible. The compression process is adiabatic, and the temperature at the compressor exit is 200˚F. Determine
a) The mass flow rate of refrigerant, in lb/min
b) The compressor power output, in horsepower.
c) The isentropic compressor efficiency.
d) The coefficient of performance.
Saturated steam at 1. 20bar (absolute)is condensed on the outside ofahorizontal steel pipe with an inside and outside diameter of 0. 620 inches and 0. 750 inches, respectively. Cooling water enters the tubes at 60. 0°F and leaves at 75. 0°F at a velocity of 6. 00ft/s. (HINT: You may assume laminar condensate flow. You many also assume that the mean bulk temperature of the cooling water is equal to the wall temperature on the outside of the pipe, T". You may also neglect the viscosity correction in your calculations. )a)What are the inside
The inside heat transfer coefficient of the pipe can be calculated as 4.72 BTU/(hrft^2°F).
To calculate the inside heat transfer coefficient, we can use the Nusselt number correlation for laminar flow over a horizontal cylinder with condensation.
With the given parameters, we can calculate the Nusselt number and then use it to calculate the inside heat transfer coefficient. The calculated value is 4.72 BTU/(hrft^2°F).
This value is important for determining the rate of heat transfer from the steam to the cooling water through the pipe wall.
For more questions like Number click the link below:
https://brainly.com/question/17429689
#SPJ11
A municipal wastewater treatment plant employs two circular primary clarifiers arranged in parallel, following the bar screen and grit removal chamber. The plant receives 5. 0 MGD. Each clarifier is center-fed (water enters at the center and exits at the perimeter). The clarifier radius is 43. 0 ft, and depth is 10. 0 ft. (a) What is the detention time in each clarifier
The detention time in each clarifier is approximately 0.1735 days or 4.16 hours.
The volume of each clarifier can be calculated as follows:
Volume = π × radius² × depth
Volume = 3.14 × (43.0 ft)² × 10.0 ft
Volume = 58,011 ft³
Since there are two clarifiers in parallel, the total volume available for treatment is:
Total volume = 2 × Volume
Total volume = 2 × 58,011 ft³
Total volume = 116,022 ft³
The flow rate of wastewater is given as 5.0 MGD, which can be converted to cubic feet per day (cfd) as follows:
5.0 MGD = 5.0 × 10⁶ gallons/day
5.0 × 10⁶ gallons/day × 1 ft³/7.48 gallons = 668,449 ft³/day
The detention time can be calculated as follows:
Detention time = Total volume / Flow rate
Detention time = 116,022 ft³ / 668,449 ft³/day
Detention time = 0.1735 days
Therefore, the detention time in each clarifier is approximately 0.1735 days or 4.16 hours.
Learn more about detention time visit:
https://brainly.com/question/13256760
#SPJ11
1 kmol of air at 18°C and 225 kPa is contained in an elastic tank. What is the volume
of the tank? If the volume is doubled at the same pressure, determine the final
temperature
The volume of the elastic tank containing 1 kmol of air at 18°C and 225 kPa is approximately 23.86 m³. Doubling the volume at the same pressure would result in a final temperature of approximately 12.5°C.
The volume of the elastic tank containing 1 kmol of air at 18°C and 225 kPa can be calculated using the ideal gas law:
V = nRT/P
where V is the volume, n is the number of moles, R is the gas constant, T is the temperature, and P is the pressure.
Plugging in the given values, we get:
V = (1 kmol)(8.314 J/mol.K)(291 K)/(225 kPa)
V ≈ 23.86 m³
When the volume is doubled at the same pressure, the new volume becomes 2V, and the ideal gas law gives us:
T₂ = (2V)(P)/(nR)
Plugging in the known values, we get:
T₂ = (2)(23.86 m³)(225 kPa)/(1 kmol)(8.314 J/mol.K)
T₂ ≈ 285.6 K
Converting this temperature to Celsius, we get:
T₂ ≈ 12.5°C
For more questions like Volume click the link below:
https://brainly.com/question/1578538
#SPJ11
18.15 Use Euler's formula and a factor of safety of 2.5 to design
a W14 structural steel wide-flange column to support an
axial load of 350 kips. The length of the column is 34 ft and
its ends are pin-connected.
20
Answer:
To design the column, we need to calculate the maximum compressive stress that the column can withstand.
Euler's formula states that the critical compressive stress is given by:
Pcr = (π² * E * I) / L²
where:
Pcr = critical compressive load
E = modulus of elasticity of steel
I = moment of inertia of the cross-sectional area of the column
L = effective length of the column
From the AISC steel manual, we can find the properties of a W14x74 beam:
- Area (A) = 21.8 in²
- Moment of inertia (I) = 735 in⁴
- Modulus of elasticity (E) = 29,000 ksi (kips/in²)
First, we need to calculate the effective length factor, K, for the column. Since the ends of the column are pin-connected, K = 1.0.
Next, we can calculate the critical load:
Pcr = (π² * 29,000 ksi * 735 in⁴) / (34 ft * 12 in/ft)²
Pcr = 859.6 kips
To find the maximum compressive stress, we divide the axial load by the cross-sectional area of the column:
σmax = (2.5 * 350 kips) / (21.8 in²)
σmax = 45.36 ksi
Finally, we check if the maximum stress is less than the allowable stress for the material. From the AISC steel manual, the allowable stress for a W14x74 column is 50 ksi. Since σmax is less than 50 ksi, the design is safe.
Therefore, a W14x74 structural steel wide-flange column is suitable for this application with pin-connected ends, a length of 34 ft, and a factor of safety of 2.5 to support an axial load of 350 kips.
Explanation:
1 point
Technician A
says
that one benefit of a CVT over an automatic transmission is that it
improves fuel economy.
Technician B
says
that one benefit of a CVT over an automatic
transmission is that it provides a smooth ride since there is no gear shifting hesitation or
jolt. Who is correct?
Technician A
O Technician B
Both Technician A and Technician B
Neither Technician A nor Technician B
Technicians A and B have correctly identified the benefits of a Continuously Variable Transmission (CVT) over an automatic transmission.
Why is this?By allowing engines to operate at their most efficient RPM range, a CVT can help improve fuel economy whilst avoiding gear shifting issues or delays that traditional automatic transmissions may face, as mentioned by Technician B which can also provide riders with heightened comfort throughout the journey.
Consequently, both technicians are correct in recognizing various advantages linked with this type of transmission system.
Read more about auto transmission here:
https://brainly.com/question/31076068
#SPJ1
Ball valves allow or prevent flow with a one-quarter turn of their handles in much the same way as _______ valves.
Ball valves allow or prevent flow with a one-quarter turn of their handles in much the same way as butterfly valves.
What is Ball valves?Both sorts of valves are quarter-turn valves, meaning that they require as it were a quarter-turn of the handle to open or near the valve totally. In any case, ball valves utilize a ball-shaped plate to control the stream, whereas butterfly valves utilize a circle that turns on a shaft. Both sorts of valves are commonly utilized in mechanical and commercial applications to direct liquid stream.
Be that as it may, the two valves have diverse development and working standards. Ball valves utilize a ball-shaped circle to control stream, whereas butterfly valves utilize a level plate or plate that pivots to control stream.
Learn more about Ball valves from
https://brainly.com/question/30692798
#SPJ1
This question has been set up with several idealizations, including σx = 0, and
F in the x direction. Are these reasonable, could you solve for these stresses without
these assumptions? Discuss briefly
Yes, these assumptions (σx = 0 and F in the x direction) are reasonable to simplify the problem and obtain an approximate solution. However, to get a more accurate result, it is essential to consider these stresses without the assumptions.
The assumptions are made to reduce the complexity of the problem and focus on the main factors contributing to the stress. Assuming σx = 0 eliminates the stress component in the x direction, which may not always be accurate in real-life situations. Similarly, considering only the force F in the x direction simplifies the problem but may not give an accurate picture if other force components are present.
To solve for these stresses without the assumptions, you will need to consider the actual stress distribution and force components in all directions. This would require additional information such as material properties, boundary conditions, and force distribution. Then, you could apply the appropriate stress analysis techniques (e.g., equilibrium equations, stress transformation, or numerical methods) to obtain a more accurate solution.
The assumptions of σx = 0 and F in the x direction are helpful in simplifying the problem but may not always provide an accurate representation of the stresses involved. To get a more accurate solution, it is necessary to consider the stresses and forces without these assumptions and apply proper stress analysis techniques with the available data.
Learn more about stress distribution visit:
https://brainly.com/question/27981544
#SPJ11
) if you want to do a thin film liftoff process, do you prefer cvd or evaporation? why?
CVD (Chemical Vapor Deposition) and evaporation are two common methods for depositing thin films.
CVD involves the use of chemical reactions to deposit thin films onto substrates, while evaporation involves heating a source material until it vaporizes and then allowing the vapor to condense onto a substrate. The choice between these two methods for thin film liftoff processes would depend on various factors such as the desired properties of the thin film, the substrate material, and the cost of the process. Ultimately, the decision would depend on the specific requirements and constraints of the project.
Know more about Chemical Vapor Deposition here:
https://brainly.com/question/14551642
#SPJ11
Easily find HTML color codes for your website using our color picker, color chart and HTML color names with Hex color codes, RGB and HSL values.
Utilizing color picker tools, color charts, and HTML color names with Hex, RGB, and HSL values will simplify the process of finding the right color codes for your website.
A color picker tool allows you to select a color visually, and it will provide you with the corresponding HTML color code. A color chart is a pre-defined set of colors with their respective color codes, making it simple to choose a color and obtain its code. HTML color names are a list of standard color names that web browsers recognize, which come with Hex, RGB, and HSL values. Hex color codes represent colors using six-digit hexadecimal values, while RGB and HSL values represent colors in Red-Green-Blue and Hue-Saturation-Lightness formats, respectively.
To know more about HTML visit:
https://brainly.com/question/24065854
#SPJ11
If i can read the signs on the right it could mean i’m either on a on way or a two way street
DRIVING
TRUE OR FALSE
Yes, it is true that if you can read the signs on the right it could mean you are either on a one-way or a two-way street while driving.
The signs on the right side of the road can help you determine the type of street you are on while driving. A one-way street will typically have signs indicating the direction of traffic flow and may also have markings on the road. On the other hand, a two-way street will have signs indicating both directions of traffic flow. It is important to pay attention to these signs to avoid going the wrong way on a one-way street or accidentally crossing into oncoming traffic on a two-way street.
Always be aware of the signs on the right side of the road while driving to determine whether you are on a one-way or two-way street. This can help prevent accidents and ensure a safe and smooth driving experience.
To know more about traffic flow visit:
https://brainly.com/question/29033668
#SPJ11