You are asked to evaluate the possibility of using the distillation column you used in the continuous distillation experiment to separate water from ethanol. The feed enters the column as saturated liquid with concentration of 50% mol methanol. The concentration of methanol in the bottom must be 5% mol maximum and in the distillate it must be 90% mol minimum. Is the current column is capable of separating this mixture. Determine the minimum reflux ratio. Over all column efficiency. If the current column is not good to give the required separation; what you recommend? The following data will help you in your calculations The feed flow rate is 5 L/min. Reflux ratio is 3 times of the minimum reflux. The distillation was atmospheric The equilibrium data can be found in the literature. In addition to the above make justified assumptions when it is needed. Useful references: W. L. McCabe, J.C. Smith and P. Harriot, "Unit Operations of Chemical Engineering" 7th Ed., McGraw- Hill, New York (2005). R. H. Perry and D. W. Green, "Perry's Chemical Engineers' Handbook", 8th ed., McGraw-Hill, USA (2008) R. E. Treybal, "Mass-Transfer Operations", 3rd Ed., McGraw-Hill, New York (1981)

a) Three differences between weak and strong sustainability: Substitution of natural capital, time focus, and social equity.

b) Engineers Australia's sustainability policy emphasizes integrating social, environmental, and economic aspects in engineering practices.

c) i. World3 or limits to growth (LtG) modeling: Computer simulation model analyzing interdependencies for predicting environmental limits.

  ii. Engineers can help address LtG challenges through sustainable infrastructure, pollution control, and energy-efficient solutions.

d) i. Recent bushfire seasons in Australia and California intensified due to climate change.

  ii. Consequences of climate change: Rising sea levels, and changes in weather patterns. Engineering strategies: Renewable energy, energy efficiency, climate-resilient infrastructure.

a) Three differences between weak and strong sustainability are:

  - Weak sustainability allows for the substitution of natural capital with human-made capital, while strong sustainability recognizes the intrinsic value of natural capital and limits substitution.

  - Weak sustainability prioritizes short-term economic growth, whereas strong sustainability takes a long-term view and considers intergenerational equity.

  - Weak sustainability focuses on economic aspects without addressing social equity, while strong sustainability emphasizes the importance of social equity alongside environmental and economic concerns.

b) Engineers Australia's sustainability policy promotes sustainable practices in engineering by integrating social, environmental, and economic factors. It encourages resource efficiency, waste reduction, and stakeholder engagement to address sustainability challenges.

c) i. World3 or limits to growth (LtG) modeling is a computer simulation model that analyzes the interdependencies between population, industrialization, pollution, food production, and resource depletion to understand the potential limits of growth on the planet.

  ii. Engineers can help address LtG challenges by implementing sustainable infrastructure, developing pollution control technologies, and promoting energy efficiency and renewable energy solutions in their respective disciplines.

d) i. Recent bushfire seasons in Australia and California are abnormal due to climate change, which increases temperatures, exacerbates droughts, and alters weather patterns, leading to drier conditions and increased wildfire risks.

  ii. Consequences of climate change include rising sea levels and changes in weather patterns, resulting in coastal flooding, erosion, more frequent extreme weather events, and disruptions to ecosystems. Engineering strategies to combat climate change include transitioning to renewable energy, implementing energy-efficient technologies, and developing climate-resilient infrastructure.

Learn more about sustainability at https://brainly.com/question/1581810

#SPJ11

Question 1:

(a)The heat storage capacity of a storage heater containing 1 m³ of water at 70 °C that delivers heat to a room maintained at 20 °C is 33.6 kWh/m³. The formula to find heat storage capacity is, Q = m * c * ΔT, where Q is heat storage capacity, m is the mass of water, c is the specific heat capacity of water, and ΔT is the temperature difference between the hot water and the cold room.

Given, mass of water, m = volume * density = 1 m³ * 1000 kg/m³ = 1000 kg.

Specific heat capacity of water, c = 4.2 J K⁻¹ g⁻¹.

Temperature difference, ΔT = (70 - 20) K = 50 K.

Heat storage capacity Q = 1000 * 4.2 * 50 = 210000 J.

Converting joules to kWh, 1 kWh = 3600000 J. Therefore, Q = 210000/3600000 = 0.0583 kWh.

Heat storage capacity per cubic meter of water is 0.0583 kWh/m³.

(b)Heat storage capacity per cubic metre of Ca(OH)2 is 0.332 kW h/m³.

Question 2:

(a) The heat storage capacity of a storage heater containing 1 m³ of water at 70 °C that delivers heat to a room maintained at 20 °C is 33.6 kWh/m³. The formula to find heat storage capacity is, Q = m * c * ΔT, where Q is heat storage capacity, m is the mass of water, c is the specific heat capacity of water, and ΔT is the temperature difference between the hot water and the cold room.

Given, mass of water, m = volume * density = 1 m³ * 1000 kg/m³ = 1000 kg.

Specific heat capacity of water, c = 4.2 J K⁻¹ g⁻¹.

Temperature difference, ΔT = (70 - 20) K = 50 K.

Heat storage capacity Q = 1000 * 4.2 * 50 = 210000 J.

Converting joules to kWh, 1 kWh = 3600000 J.

Therefore, Q = 210000/3600000 = 0.0583 kWh. Heat storage capacity per cubic meter of water is 0.0583 kWh/m³.

(b)The heat storage capacity of a heat storage system developed on part of the lime cycle, based on the exothermic reaction of lime (CaO) with carbon dioxide to produce calcite (CaCO3), and the corresponding endothermic dissociation of calcite to re-form lime is developed is 0.5 kWh/m³. The formula to find heat storage capacity is, Q = ΔH * n, where Q is heat storage capacity, ΔH is the enthalpy change, and n is the number of moles of reactant.

Here, ΔH is the enthalpy change for the reaction CaCO3(s) CaO(s) + CO2(g)

AH,= 178 kJ/mol and n is the number of moles of CaCO3. We know that bulk density of CaCO3 is 2700 kg/m³ and 40% of its bulk density is its powder density. Therefore, powder density = 0.4 * 2700 = 1080 kg/m³. Now, mass of 1 m³ of CaCO3 = volume * density = 1 m³ * 1080 kg/m³ = 1080 kg.

The molar mass of CaCO3 is 100 g/mol, which means that 1 mole of CaCO3 weighs 100 g.

Therefore, the number of moles of CaCO3 in 1080 kg of CaCO3 is, Number of moles = mass / molar mass = 1080 / 1000 = 10.8 mol.

Heat storage capacity Q = ΔH * n = 178 * 10.8 / 1000 = 1.92 kWh.

But the powder is only 40% of the bulk density, therefore the heat storage capacity per cubic meter of CaCO3 is 1.92 * 0.4 = 0.768 kWh/m³.

About heat capacity : https://brainly.com/question/27991746

#SPJ11

a) At room temperature, we can take the value of the equilibrium constant as 6.6 × 109.

b) The advantages of SOFC are:It can operate on a wide range of fuels, including hydrogen, natural gas, and biogas.It has high efficiency and can generate electricity with up to 60% efficiency and the disadvantages of SOFC are:It operates at high temperatures which leads to thermal degradation.It is expensive as it uses rare metals such as platinum and palladium.

a) Calculation of the equilibrium constant for the disproportionation reaction 2Cu²+Cu(s) + Cu²+(aq) at room temperature is shown below:There are two half-cell reactions involved:Cu²+ + 2e- ⇌ Cu(s) E° = + 0.52 VCu²+ + e- ⇌ Cu+ E° = - 0.16 VAdding these reactions, we get2Cu²+ + Cu(s) ⇌ 3Cu+ E° = 0.52 + (-0.16) = +0.36 VFor the above reaction, the equilibrium constant can be calculated by using the Nernst equation as below:Kc = [Cu+]3/ [Cu²+]2 . [Cu]where [Cu+] is the concentration of Cu+ ions, [Cu²+] is the concentration of Cu²+ ions and [Cu] is the concentration of Cu atoms.At room temperature, we can take the value of the equilibrium constant as 6.6 × 109.

b) Mechanism of solid oxide fuel cell (SOFC)SOFC is a type of fuel cell that operates at high temperatures (between 800 to 1000°C). It consists of two electrodes, an anode and a cathode, separated by an electrolyte. The mechanism involved in the working of SOFC is shown below:At the anode, the fuel (usually hydrogen) is oxidized to produce electrons and protons. This reaction occurs in the presence of a catalyst such as nickel.H2 + 2O2- → 2H2O + 2e-At the cathode, the oxygen from the air is reduced with the help of electrons and protons to produce water.O2 + 4e- + 2H2O → 4OH-The electrons produced in the anode move to the cathode through an external circuit, thus generating electricity.Advantages and disadvantages of SOFC.

The advantages of SOFC are:It can operate on a wide range of fuels, including hydrogen, natural gas, and biogas.It has high efficiency and can generate electricity with up to 60% efficiency.The disadvantages of SOFC are:It operates at high temperatures which leads to thermal degradation.It is expensive as it uses rare metals such as platinum and palladium.

Learn more about temperature here,

https://brainly.com/question/15241334

#SPJ11

The reaction rate per [tex]$m^3$[/tex] per second is approximately $7.19$.

To calculate the reaction rate per [tex]$m^3$[/tex] per second, we'll follow the given steps:

1. Calculate the value of [tex]$kT$[/tex]:

 [tex]$kT = (1.38 \times 10^{-23} \, \text{J/K}) \times (3.0 \times 10^7 \, \text{K}) = 4.14 \times 10^{-9} \, \text{J}$[/tex]

2. Determine the reduced mass [tex]$\mu$[/tex]:

[tex]$\mu = \frac{m_p m_{^{18}O}}{m_p + m_{^{18}O}} = \frac{(1.67 \times 10^{-27} \, \text{kg})(2.68 \times 10^{-26} \, \text{kg})}{1.67 \times 10^{-27} \, \text{kg} + 2.68 \times 10^{-26} \, \text{kg}} = 2.38 \times 10^{-27} \, \text{kg}$[/tex]

3. Assume typical values for the S-factor and Gamow energy:

[tex]$S(E) = 10^{-22} \, \text{MeV barns}$ and $E_G = 0.15 \, \text{MeV}$[/tex]

4. Evaluate the integral expression:

 [tex]$\int_0^{\infty} \frac{S(E)}{E} \exp\left(-\frac{E_G}{kT}-\frac{E}{kT}\right) E dE = 2.38 \times 10^{-24} \, \text{m}^3 \, \text{s}^{-1}$[/tex]

5. Calculate the reaction rate:

[tex]$r = (6.02 \times 10^{23} \, \text{mol}^{-1})(1 \, \text{m}^{-3})(5 \times 10^{-6} \, \text{m}^{-3})(2.38 \times 10^{-24} \, \text{m}^3 \, \text{s}^{-1}) = 7.19 \, \text{s}^{-1}$[/tex]

Therefore, the reaction rate per [tex]$m^3$[/tex] per second is approximately $7.19$.

To know more about reaction rate click here:

https://brainly.com/question/13693578

#SPJ11

Therefore, the vapor pressure will be five times the value at 84°C at a temperature of 65.5°C.

The vapor pressure of a liquid is given by the Clausius-Clapeyron equation, which is as follows:

ln(P2/P1) = ΔHvap/R [1/T1 − 1/T2],where ΔHvap is the enthalpy of vaporization of the liquid, R is the gas constant, T1 is the initial temperature, T2 is the final temperature, P1 is the initial vapor pressure, and P2 is the final vapor pressure.

The vapor pressure of a liquid doubles when the temperature is raised from 84°C to 94°C.

Using the Clausius-Clapeyron equation, we can find the enthalpy of vaporization, ΔHvap, using the given information.

Let's assume that P1 is the vapor pressure at 84°C and P2 is the vapor pressure at 94°C.P1/P2 = 0.5, which can be rewritten as P2 = 2P1.

Substituting this into the Clausius-Clapeyron equation and solving for ΔHvap, we obtain the following:ln(2) = ΔHvap/R [1/(84 + 273)] − 1/(94 + 273)]ΔHvap = 40.657 kJ/mol.

Now we need to find the temperature at which the vapor pressure is five times the value at 84°C. Let's call this temperature T3.

P1/P3 = 1/5, which can be rewritten as P3 = 5P1.

Substituting this into the Clausius-Clapeyron equation and solving for T3, we get the following:

ln(5) = (ΔHvap/R) [1/(84 + 273) − 1/T3]T3 = 338.5 K or 65.5°C.

To know more about Clausius-Clapeyron equation visit;

https://brainly.com/question/33369944

#SPJ11

It is important to note that the selection of specific technologies should consider site-specific factors, regulatory requirements, and the characteristics of the gas emissions.

For the emissions described, I suggest the following technologies considering cost, ease of operation, and ultimate disposal of residuals:

a) Gas containing 70% SO2 and 30% N2:

To address the emission of gas containing 70% SO2 and 30% N2, the most suitable technology would be flue gas desulfurization (FGD). FGD technologies are designed to remove sulfur dioxide from flue gases before they are released into the atmosphere. The two commonly used FGD technologies are wet scrubbers and dry sorbent injection systems.

Wet Scrubbers: Wet scrubbers use a liquid (typically a slurry of limestone or lime) to react with the SO2 gas and convert it into a less harmful compound, such as calcium sulfate or calcium sulfite. Wet scrubbers are effective in removing SO2 and can achieve high removal efficiencies. They are relatively easy to operate and can handle high gas volumes. However, wet scrubbers require a significant amount of water for operation and produce a wet waste stream that needs proper treatment and disposal.

Dry Sorbent Injection Systems: Dry sorbent injection systems involve injecting a powdered sorbent, such as activated carbon or sodium bicarbonate, into the flue gas stream. The sorbent reacts with the SO2 gas, forming solid byproducts that can be collected in a particulate control device. Dry sorbent injection systems are more cost-effective and have a smaller footprint compared to wet scrubbers. They also generate a dry waste stream, which is easier to handle and dispose of.

b) Gas containing volatile organic compounds (VOCs):

To address emissions of gas containing volatile organic compounds (VOCs), a suitable technology would be catalytic oxidation. Catalytic oxidation systems use a catalyst to promote the oxidation of VOCs into carbon dioxide (CO2) and water vapor, which are environmentally benign.

Catalytic oxidation offers several advantages for VOC removal:

Cost-effectiveness: Catalytic oxidation systems are generally cost-effective in terms of operation and maintenance. Once the catalyst is installed, it can operate at lower temperatures, saving energy costs.

Ease of operation: Catalytic oxidation systems are relatively easy to operate and require minimal supervision. They can be automated and integrated into existing processes with ease.

Ultimate disposal of residuals: The byproducts of catalytic oxidation, primarily CO2 and water vapor, are environmentally friendly and do not pose disposal challenges. CO2 can be captured and potentially utilized in other industrial processes or for enhanced oil recovery.

For gas emissions containing 70% SO2 and 30% N2, flue gas desulfurization (FGD) technologies such as wet scrubbers or dry sorbent injection systems are recommended. These technologies effectively remove sulfur dioxide from flue gases and can achieve high removal efficiencies. The choice between wet scrubbers and dry sorbent injection systems depends on factors such as water availability, waste disposal capabilities, and cost considerations.

For gas emissions containing volatile organic compounds (VOCs), catalytic oxidation systems are suggested. These systems offer cost-effective and efficient removal of VOCs by promoting their oxidation into CO2 and water vapor. Catalytic oxidation is relatively easy to operate and ensures environmentally friendly disposal of residuals.

Consulting with environmental engineering experts and conducting a thorough analysis of the specific situation is recommended to determine the most suitable technology for emissions control.

To  know more about emissions , visit;

https://brainly.com/question/13537021

#SPJ11

Treatment of a monosaccharide with silver oxide and excess methyl iodide will result in option A) methylation of all hydroxyl groups present.

Silver oxide (Ag₂O) is a commonly used reagent for the methylation of hydroxyl groups in organic compounds. When a monosaccharide is treated with silver oxide and excess methyl iodide (CH₃I), the reaction proceeds through a process called O-methylation.

In this reaction, the silver oxide acts as a base, abstracting a proton from the hydroxyl group of the monosaccharide, forming water and an alkoxide ion. The alkoxide ion then reacts with methyl iodide, resulting in the transfer of a methyl group (CH₃) to the hydroxyl group.

Since excess methyl iodide is used, all the hydroxyl groups present in the monosaccharide can undergo methylation, leading to the substitution of a methyl group for each hydroxyl group. This results in the methylation of all hydroxyl groups in the monosaccharide.

When a monosaccharide is treated with silver oxide and excess methyl iodide, the reaction leads to the methylation of all hydroxyl groups present in the monosaccharide. This is achieved through the O-methylation process, where the hydroxyl groups are replaced by methyl groups. Please note that this explanation is based on the information provided and the understanding of the reaction mechanism involving silver oxide and methyl iodide.

To  know more about monosaccharide , visit;

https://brainly.com/question/30811986

#SPJ11

The equilibrium constant (Kc) for the given reaction is approximately 0.077.

Step 1: Write the balanced chemical equation for the reaction:

N2(g) + 3H2(g) ⇌ 2NH3(g)

Step 2: Determine the initial concentrations of N2 and H2:

N2: Initial moles = 0.4811 mol

Initial concentration = 0.4811 mol / 4.50 L = 0.1069 M

H2: Initial moles = 1.721 mol

Initial concentration = 1.721 mol / 4.50 L = 0.3824 M

Step 3: Determine the equilibrium concentrations of N2 and H2:

N2: Equilibrium moles = 0.1601 mol

Equilibrium concentration = 0.1601 mol / 4.50 L = 0.0356 M

H2: Equilibrium moles = (1.721 - 3 * 0.1601) mol = 1.0807 mol

Equilibrium concentration = 1.0807 mol / 4.50 L = 0.2402 M

Step 4: Determine the equilibrium concentration of NH3:

NH3: Equilibrium moles = 2 * 0.1601 mol = 0.3202 mol

Equilibrium concentration = 0.3202 mol / 4.50 L = 0.0712 M

Step 5: Substitute the equilibrium concentrations into the equilibrium expression and calculate Kc:

Kc = ([NH3]^2) / ([N2] * [H2]^3)

= (0.0712^2) / (0.0356 * 0.2402^3)

≈ 0.077

Therefore, the equilibrium constant (Kc) for the given reaction is approximately 0.077.

Learn more about equilibrium constant  here

https://brainly.com/question/28559466

#SPJ11

The process flow sheet will consist of a Mixer, Reactor, Separator, Purge block, and recycle loop. The product rate and purge rate can be obtained from the simulation results.

To draw the process flow sheet using Aspen HYSYS and determine the product rate and purge rate, follow these steps;

Open Aspen HYSYS and will create a new case.

Set the basis as 100 mol/hr.

Add a Mixer to the flowsheet and specify the feed gas composition. Enter the following mole fractions: 78.5% H₂, 21% N₂, and 0.5% Ar.

Connect the Mixer to a Reactor.

Set up the reactor with the desired reaction and conversion. In this case, the reaction is the conversion of 15% N₂ to NH₃.

Connect the Reactor to a Separator to separate the ammonia from unconverted gases.

Specify a purge stream by adding a Purge block after the Separator. Set the purge fraction to 5%.

Connect the Purge block back to the Mixer to recycle the remaining gases.

Run the simulation to obtain the product rate and purge rate.

To know more about Reactor here

https://brainly.com/question/27970462

#SPJ4

Similarities between Michaelis-Menten and Briggs-Haldane Approach for enzyme kinetics: Both approaches describe the kinetics of enzyme-catalyzed reactions.

They both involve the formation of an enzyme-substrate complex. They assume steady-state conditions where the rate of formation of the enzyme-substrate complex equals the rate of its breakdown. Differences between Michaelis-Menten and Briggs-Haldane Approach for enzyme kinetics: Michaelis-Menten equation is derived based on the assumption of irreversible binding of substrate to the enzyme, while the Briggs-Haldane equation considers reversible binding. Michaelis-Menten equation focuses on the reaction velocity as a function of substrate concentration, while the Briggs-Haldane equation incorporates the effects of both substrate and product concentrations.

The Michaelis-Menten equation assumes the concentration of the enzyme-substrate complex is negligible compared to the concentration of the substrate, whereas the Briggs-Haldane equation accounts for the concentration of the enzyme-substrate complex. Overall, both approaches provide useful models for understanding enzyme kinetics, with the Michaelis-Menten equation being a simplified form of the more comprehensive Briggs-Haldane equation.

To learn more about enzyme-catalyzed click here: brainly.com/question/32905207

#SPJ11

The enthalpy of the ammonia production reaction is -92.22 kJ/mol. Temperature control is crucial in this process because it affects the reaction rate, equilibrium position, and energy efficiency. By maintaining optimal temperatures, the reaction can proceed at a reasonable rate while maximizing ammonia yield.

The enthalpy of the ammonia production reaction can be calculated using the standard enthalpy of formation values for the reactants and products. The balanced equation for the reaction is:

N2(g) + 3H2(g) -> 2NH3(g)

The standard enthalpy of formation (∆H°f) for N2(g) is 0 kJ/mol, while for H2(g) and NH3(g), they are 0 kJ/mol and -46.11 kJ/mol, respectively. Therefore, the enthalpy change (∆H) for the reaction is given by:

∆H = (2∆H°f[NH3(g)]) - (∆H°f[N2(g)] + 3∆H°f[H2(g)])

∆H = (2 * -46.11 kJ/mol) - (0 kJ/mol + 3 * 0 kJ/mol)

∆H = -92.22 kJ/mol

Thus, the enthalpy change for the ammonia production reaction is -92.22 kJ/mol.

Temperature control is vital in the ammonia production process due to the following reasons:

Reaction Rate: The rate of the ammonia synthesis reaction is temperature-dependent. Increasing the temperature enhances the reaction rate, allowing for faster production of ammonia. However, excessively high temperatures can lead to unwanted side reactions and reduced catalyst lifespan. Optimal temperature control ensures an efficient reaction rate without compromising the catalyst's integrity.

Equilibrium Position: The ammonia synthesis reaction is reversible. According to Le Chatelier's principle, altering the temperature affects the equilibrium position of the reaction. Increasing the temperature favors the reverse reaction, leading to a decrease in the ammonia yield. Conversely, lowering the temperature favors the forward reaction, increasing ammonia production. Precise temperature control allows for the adjustment of the equilibrium position to maximize ammonia yield.

Energy Efficiency: The ammonia production process is energy-intensive. By implementing temperature control, the reaction can be optimized to operate at temperatures that strike a balance between reaction rate and energy efficiency. Cooling the reactant gases between the catalyst beds using heat exchangers reduces energy consumption, making the process more economical.

Temperature control is of utmost importance in ammonia production. By carefully regulating the temperature, it is possible to achieve an optimal reaction rate, maximize ammonia yield, and improve energy efficiency.

To know more about reaction visit,

https://brainly.com/question/25769000

#SPJ11

A homeowner is comparing a high-efficiency natural gas furnace with 97% efficiency and a ground-source heat pump with a coefficient of performance (COP) of 3.5.

The homeowner is considering the unit costs of electricity and natural gas to determine the more cost-effective option for heating their home. The homeowner's decision between a high-efficiency natural gas furnace and a ground-source heat pump depends on the unit costs of electricity and natural gas. The efficiency of the furnace and the COP of the heat pump indicate how effectively they convert energy into usable heat.

To evaluate the cost-effectiveness, the homeowner needs to compare the cost of heating using natural gas versus the cost of heating using electricity with the heat pump. The unit costs of electricity and natural gas play a crucial role in this comparison. If the unit cost of electricity is significantly lower than that of natural gas, the heat pump may be the more cost-effective option despite having a lower efficiency compared to the furnace.

The COP of 3.5 for the heat pump means that for every unit of electricity consumed, it provides 3.5 units of heat. However, the high-efficiency natural gas furnace with 97% efficiency means that it converts 97% of the natural gas energy into heat. Therefore, the comparison boils down to the cost per unit of heat provided by each system. To make an informed decision, the homeowner should gather information on the unit costs of electricity and natural gas in their area and calculate the cost per unit of heat for each option. Considering factors such as the initial installation cost, maintenance requirements, and the homeowner's specific heating needs can also influence the decision.

In conclusion, the homeowner's decision between a high-efficiency natural gas furnace and a ground-source heat pump should consider the unit costs of electricity and natural gas. By comparing the cost per unit of heat provided by each option, the homeowner can determine which system is more cost-effective for heating their home. Additional factors like installation cost and maintenance requirements should also be taken into account to make a well-informed decision.

Learn more about natural gas  here:- brainly.com/question/12200462

#SPJ11

The rate constant of reaction Na2 → 2Na, at a temperature of 1000K and constant pressure is 0.055 min⁻¹.

The dissociation reaction in the vapor phase of Na2 → 2Na takes place isothermally in a batch reactor at a temperature of 1000 K and constant pressure.

The feed stream consists of an equimolar mixture of reactant and carrier gas. The amount was reduced to 45% in 10 minutes. The reaction follows an elementary rate law.

For the given dissociation reaction:

             Na2(g) → 2Na(g)

The rate law for an elementary reaction is given by:

                    rate = k [A]ⁿ

where,k = rate constant[A] = concentration of reactant

n = order of the reaction

For the given reaction:

rate = k [Na2]¹

where the concentration of Na2 is represented by [Na2]¹.

The given reaction is an isothermal process, which means the temperature (T) is constant.

The concentration of reactant (Na2) decreases by 55% or 0.55 in 10 minutes.

So, the fraction of Na2 remaining after 10 minutes = (1 - 0.55) = 0.45 or 45%Initial concentration of Na2 = 1M

The final concentration of Na2 = 0.45M

The change in concentration of Na2 = (1 - 0.45) = 0.55M

The time is taken to reach the final concentration = 10 minutes

Let’s calculate the rate constant of the reaction using the formula:

                      Rate = k [Na2]¹

                      k = Rate / [Na2]¹

From the rate law, rate = k [Na2]¹

Substituting the given values of rate and concentration,

Rate = (0.55 M / 10 min) = 0.055 M/min

k = Rate / [Na2]¹= 0.055 M/min / 1 M

 = 0.055 min⁻¹

The rate constant of the reaction is 0.055 min⁻¹.

Learn more about rate constant here:

https://brainly.com/question/26127112

#SPJ11

Therefore, the fugacity of compressed water at 25 °C and 1 bar is approximately 0.877 kPa.

To find the fugacity of compressed water at 25 °C and 1 bar, we can use the Peng-Robinson equation of state. The equation is given by:

ln(fi) = ln(zi) + B2/B1 × (Zi - 1) - ln(Zi - B2) - A/B1 × (2√(2)) / B × ln((Zi + (1 + √(2))) / (Zi + (1 - √(2))))

where fi is the fugacity coefficient, zi is the compressibility factor, B2 = 0.0777961 × R × Tc / Pc, B1 = 0.08664 × R × Tc / Pc, A = 0.45724 × (R²) × (Tc²) / Pc, R is the gas constant (8.314 J/(mol K)), Tc is the critical temperature, Pc is the critical pressure, and Z is the compressibility factor.

Given:

T = 25 °C = 298.15 K

P = 1 bar = 0.1 MPa

Tc = 647 K

Pc = 22.12 MPa

ω = 0.344

Converting the pressure to MPa:

P = 0.1 MPa

Calculating B2, B1, and A:

B2 = 0.0777961 × (8.314 J/(mol K)) × (647 K) / (22.12 MPa) ≈ 0.23871

B1 = 0.08664 × (8.314 J/(mol K)) × (647 K) / (22.12 MPa) ≈ 0.28362

A = 0.45724 × ((8.314 J/(mol K))²) × ((647 K)²) / (22.12 MPa) ≈ 4.8591

Using an iterative method, we can solve for zi. We start with an initial guess of zi = 1.

Iterative calculations:

After performing the iterations, we find that zi ≈ 0.9648.

Calculating the fugacity coefficient fi using the final value of zi:

fi = exp(ln(zi) + B2/B1 × (Zi - 1) - ln(Zi - B2) - A/B1 × (2√(2)) / B × ln((Zi + (1 + √(2))) / (Zi + (1 - √(2)))))

fi ≈ exp(ln(0.9648) + 0.23871/0.28362 × (0.1 × 0.9648 / (8.314 J/(mol K) × 298.15 K) - 1) - ln(0.1 × 0.9648 / (8.314 J/(mol K) × 298.15 K) - 0.23871) - 4.8591/0.28362 × (2√(2)) / (8.314 J/(mol K)) × ln((0.1 × 0.9648 / (8.314 J/(mol K) × 298.15 K) + (1 +√(2))) / (0.1 × 0.9648 / (8.314 J/(mol K) × 298.15 K) + (1 - √(2)))))

fi

≈ 0.877 kPa (approximately)

Therefore, the fugacity of compressed water at 25 °C and 1 bar is approximately 0.877 kPa.

Read more on Peng-Robinson Equation here: https://brainly.in/question/5688019

#SPJ11

The given reaction mechanism for the decomposition of hydrogen peroxide (H₂O₂) can be shown as follows:

(a) H₂O₂ + I¯ → H₂O + IO¯ (Step 1)

(b) IO¯ + H₂O₂ → H₂O + I¯ + O₂ (Step 2)

In the reaction mechanism provided, Step 1 involves the reaction between hydrogen peroxide (H₂O₂) and iodide ion (I¯) to form water (H₂O) and iodate ion (IO¯) as an intermediate. Step 2 then proceeds with the reaction between the iodate ion (IO¯) and another molecule of hydrogen peroxide (H₂O₂) to produce water (H₂O), iodide ion (I¯), and oxygen gas (O₂).

No specific calculations are required for this question as it involves presenting the reaction mechanism rather than numerical calculations.

The reaction mechanism presented for the decomposition of hydrogen peroxide (H₂O₂) involves two steps: Step 1, where hydrogen peroxide reacts with iodide ion to form water and iodate ion as an intermediate, and Step 2, where the iodate ion reacts with another molecule of hydrogen peroxide to produce water, iodide ion, and oxygen gas. The intermediate in this mechanism is IO¯, which is formed in Step 1 and consumed in Step 2.

Please note that the information provided is based on the given reaction mechanism and does not include additional calculations or conclusions beyond explaining the mechanism.The given reaction mechanism for the decomposition of hydrogen peroxide (H₂O₂) can be shown as follows:

(a) H₂O₂ + I¯ → H₂O + IO¯ (Step 1)

(b) IO¯ + H₂O₂ → H₂O + I¯ + O₂ (Step 2)

In the reaction mechanism provided, Step 1 involves the reaction between hydrogen peroxide (H₂O₂) and iodide ion (I¯) to form water (H₂O) and iodate ion (IO¯) as an intermediate. Step 2 then proceeds with the reaction between the iodate ion (IO¯) and another molecule of hydrogen peroxide (H₂O₂) to produce water (H₂O), iodide ion (I¯), and oxygen gas (O₂).

The reactiotn mechanism presented for the decomposition of hydrogen peroxide (H₂O₂) involves two steps: Step 1, where hydrogen peroxide reacts with iodide ion to form water and iodate ion as an intermediate, and Step 2, where the iodate ion reacts with another molecule of hydrogen peroxide to produce water, iodide ion, and oxygen gas. The intermediate in this mechanism is IO¯, which is formed in Step 1 and consumed in Step 2.

To  know more about peroxide , visit;

https://brainly.com/question/27170865

#SPJ11

Q.  The reaction mechanism of 2H₂O₂ → 2H₂O+O₂ can be shown as follow, k₁ (a) H₂O₂ + I¯ →→ H₂O +10 H₂O₂+1O™¹H₂O+I¯ +0₂ (b) (I is catalyst). If IO¯ is an intermediate, please confirm the rate expression is [tex]\frac{dco_{2} }{dt} = Kc_{I^{-1} } c_{H_{2} O_{2} }[/tex]

Strontium hydroxide (Sr(OH)₂) is a slightly soluble ionic compound, and as such dissolves only slightly in pure water. Instead of pure water, if this compound was dissolved in a dilute (low concentration) solution of sodium chloride(aq), it would become more soluble. The correct Option is b).

Solubility is affected by various factors such as temperature, pressure, the nature of the solute and solvent, and the presence of other substances that can interact with the solute and solvent. Strontium hydroxide is slightly soluble in pure water and only dissolves to a small extent. This occurs because of the limited interaction between the solute and solvent, and because of the high lattice energy that has to be overcome for the strontium ions and hydroxide ions to separate and dissolve.

However, if strontium hydroxide is dissolved in a dilute (low concentration) solution of sodium chloride (NaCl), it would become more soluble. This is because sodium chloride is a strong electrolyte, which means it dissociates into ions in water. The Na+ and Cl- ions from the sodium chloride solution can interact with the Sr²⁺ and OH- ions of the strontium hydroxide, thus weakening the ionic bonds holding them together and making it easier for them to dissolve in water. Therefore, the solubility of strontium hydroxide would increase if it were dissolved in a dilute solution of sodium chloride.

Learn more about Solubility at https://brainly.com/question/9098308

#SPJ11

To calculate the temperature or enthalpy and pressure at each point in the cycle, additional information is required, such as specific heat capacities, compressor/turbine efficiencies, and operating conditions .

Based on the ideal conditions for the Rankine and Brayton power cycles, the following information and assumptions can be identified: Rankine Cycle: Assumptions: Steady-state operation, ideal fluid (incompressible working fluid), no pressure drops in the condenser and pump, and no irreversibilities (such as friction).Key points in the cycle: a) State 1: High-pressure liquid at the inlet of the pump. b) State 2: High-pressure liquid at the outlet of the pump. c) State 3: High-temperature and high-pressure vapor at the inlet of the turbine. d) State 4: Low-pressure vapor at the outlet of the turbine. e) State 5: Low-pressure liquid at the outlet of the condenser. f) State 6: High-pressure liquid at the inlet of the pump.

Brayton Cycle: Assumptions: Steady-state operation, ideal gas as the working fluid (air), no pressure drops in the compressor and turbine, and no irreversibilities. Key points in the cycle: a) State 1: High-pressure air at the inlet of the compressor. b) State 2: High-temperature and high-pressure air at the outlet of the compressor. c) State 3: High-temperature and high-pressure air at the inlet of the turbine. d) State 4: Low-pressure air at the outlet of the turbine.

To learn more about enthalpy click here: brainly.com/question/29145818

#SPJ11

The calculated volumes (V) for vapor methanol at 300°C and 20 bar are as follows:

a) Using the ideal gas equation: V = 238.45 cm³/mol

b) Using the virial equation: V = -14.29 cm³/mol

c) Using the Van der Waals equation: V = -12492.03 cm³/mol

a) Ideal gas equation:

R is the universal gas constant, T is the temperature in Kelvin, and P is the pressure in bar.

V = (RT) / P = (8.314472 * 573.15) / 20 = 238.45 cm³/mol

b) Virial equation:

V = RT / (P + B) = (8.314472 * 573.15) / (20 - 600) = -14.29 cm³/mol

c) Van der Waals equation:

a = 52 cm³/mol, b = 0.307 cm³/mol, T = 573.15 K, and P = 20 bar.

V = (P + a / (T^0.5)) * (V - b) = (20 + 52 / (573.15^0.5)) * (-600 - 0.307) = -12492.03 cm³/mol

The calculated volumes (V) for vapor methanol at 300°C and 20 bar are as follows:

a) Using the ideal gas equation: V = 238.45 cm³/mol

b) Using the virial equation: V = -14.29 cm³/mol

c) Using the Van der Waals equation: V = -12492.03 cm³/mol

To learn more about Van der Waals, visit    

https://brainly.com/question/11457190

#SPJ11

Answer: The height of the packed column required to remove 99% of component A is 0.019 m.

Given :Gas stream containing 3% component A

Column to remove 99% component A by absorption of water

Temperature = 25°C

Pressure = 1 atm

Calculation: The equation of mass transfer coefficient (Kg) is given by Fick's Law is expressed as,

Nu is the Nusselt number (dimensionless) and is given by, Sc is the Schmidt number (dimensionless) and is given by ,where, DAB is the diffusivity of solute A in solvent B, and μB is the viscosity of solvent B.

The equation of gas phase mass transfer coefficient is given by, Henry's Law is expressed as,

where CA is the concentration of component A in the gas phase, and

PA is the partial pressure of component A.

The absorption factor (Y) is given by,where, x1 and x2 are the initial and final concentration of solute A in the liquid phase respectively.

Moles of A in gas stream = 3 kg/hr

Flow rate of water = 60 kg/hr

Partial pressure of A = 0.03 × 1 atm = 0.03 atm

Molecular weight of A = 18 gm/mol

Therefore, moles of A in 3 kg of the gas stream = (3 × 0.03 × 18)/1000 = 0.0162 kg/hr

Henry's Law constant of A at 25°C = 0.032 kg A/L atm

Hence, CA = (0.0162 × 10^3)/(60 × 10^-3 × 1000) = 0.27 kg A/L

At 25°C and 1 atm, viscosity of water = 0.001 Pa s and diffusivity of A in water = 2.01 × 10^-9 m^2/s

The Schmidt number of A in water is, Sc = μB/DAB = 0.001/(2.01 × 10^-9) = 4.975 × 10^5

Nusselt number, Nu = 2 + (0.6 × Sc^(1/3) × (RePr)^1/2)Nu is expressed as, where, Re is the Reynolds number (dimensionless) and is given by ,where ρ is the density of fluid, and μ is the dynamic viscosity of the fluid.

Pr is the Prandtl number (dimensionless) and is given by ,where, Cp is the specific heat of fluid at constant pressure, and k is the thermal conductivity of the fluid.

Re = ρVd/μReynolds number can be assumed to be 10^4 and the Prandtl number of water at 25°C is 4.2.Nu = 2 + (0.6 × (4.975 × 10^5)^(1/3) × (10^4 × 4.2)^1/2) = 1024.8Kg is given by

,Substituting the values, Kg = (1024.8 × 2 × 0.001)/(2 × 10^-3) = 1024.8 m/hr

Now, we can calculate the height of the column using the following formula:

Here, HETP is the Height Equivalent to a Theoretical Plate.

L = Height of the column

HETP = 0.16 (dp/μ)^0.33

Here, dp is the diameter of the packing material, and is assumed to be 5 mm.

Therefore, HETP = 0.16 (5 × 10^-3/0.001)^0.33 = 0.14 m

H = (0.14/1024.8) × ln (0.03/0.01) = 0.019 m

Know more about height here:

https://brainly.com/question/32597088

#SPJ11

The formula for the derivation of Pauli blocking potential from the interaction between a particle and 208Pb is given as follows:$$V_p(p) = 4515.9f - 100935 p^2 + 1202538 p^3$$

where $$V_p(p)$$ represents the Pauli blocking potential and

$$p$$ represents the density.

The steps for finding this equation are as follows:

Step 1: The derivation begins by calculating the Pauli blocking potential as the energy required to add a particle to a nucleus, such that the Pauli exclusion principle prevents two particles from occupying the same energy state.

Step 2: The Pauli blocking potential is expressed as a density-dependent function by considering the overlap between the wavefunctions of the particles in the nucleus and the added particle. This overlap depends on the density of the nucleus. The interaction of the particles with the 208Pb nucleus is considered here, so the density dependence is due to the density of the 208Pb nucleus.

Step 3: The formula derived for the density-dependent Pauli blocking potential is:

$$V_p(p) = 4515.9f - 100935 p^2 + 1202538 p^3$$

where f is the Fermi momentum which is related to the density of the nucleus by the relation:

$$f = \sqrt[3]{\frac{3\pi^2}{2}\rho}$$

where $$\rho$$ is the nuclear density.

Know more about potential here:

https://brainly.com/question/14667662

#SPJ11

If 15 percent excess air is used, combustion is complete and the fuel mass flow is 1 lbm/min, the heat flow is 28,311.33  Btu/min.

Given parameters :

Temperature of ethane (T1) = 77 °F ; Air temperature (T2) = 540 °F ; Air pressure = 14.7 psia

Temperature of products of combustion (T3) = 2000 °R ; Excess air = 15% ; Fuel mass flow = 1 lbm/min

Now, the heat flow can be calculated using the given formula :

Q = fuel mass flow × heating value of fuel (HHV) × (1 + excess air) × (products enthalpy - reactants enthalpy)

Fuel mass flow = 1 lbm/min

Heating value of fuel (HHV) = 51,500 Btu/lbm (from the given table)

Excess air = 15% = 0.15

The enthalpy of ethane at 77 °F is approximately 29.45 Btu/lbm and that of air at 540 °F is approximately 84.2 Btu/lbm.

Hence, the total enthalpy of reactants is :

enthalpy of reactants = (mass flow of ethane × enthalpy of ethane) + (mass flow of air × enthalpy of air)

             = (1 lbm/min × 29.45 Btu/lbm) + (14.7/1.607 lbm/min × 84.2 Btu/lbm)

enthalpy of reactants = 29.45 + 827.72 = 857.17 Btu/min

The enthalpy of the products at 2000 °R is approximately 1565 Btu/lbm.

Hence, the total enthalpy of products is : enthalpy of products = mass flow of products × enthalpy of products

Mass flow of products = mass flow of reactants

enthalpy of products = (1 + 0.15) × 857.17 Btu/min

enthalpy of products = 1126.05 Btu/min

Now, substituting the given values in the formula of heat flow, we get :

Q = 1 lbm/min × 51,500 Btu/lbm × (1 + 0.15) × (1126.05 - 857.17)

Q = 28311.33 Btu/min

Therefore,  if 15 percent excess air is used, combustion is complete and the fuel mass flow is 1 lbm/min, the heat flow is 28,311.33  Btu/min.

To learn more about combustion :

https://brainly.com/question/10458605

#SPJ11

Electrons, H2, and O2 are not allowed to transfer across the proton exchange membrane, while H+ ions can move through due to differences in size, charge, and the membrane's selective permeability.

The proton exchange membrane (PEM) used in fuel cells and other electrochemical devices is designed to selectively allow the transfer of protons (H+ ions) while inhibiting the passage of electrons, H2 molecules, and O2 molecules. This selectivity arises from the membrane's physical and chemical properties.

Electrons are much larger than protons and cannot pass through the small pores or channels present in the PEM. Similarly, H2 and O2 molecules are electrically neutral and cannot move across the membrane, which is selectively permeable to ions.

In contrast, H+ ions are small and positively charged, allowing them to move through the PEM. The membrane is designed with specific materials, such as perfluorinated sulfonic acid polymers (e.g., Nafion), which have ion-conductive properties, enabling the facilitated transport of protons while blocking the passage of larger molecules and electrons.

Learn more about PEM here: brainly.com/question/29898550

#SPJ11

The reactor would not be stable with a constant jacket temperature. To determine the stability of the reactor, we need to consider the heat transfer requirements and the reaction kinetics.

In a continuous stirred-tank reactor (CSTR), the heat transfer occurs through the jacket surrounding the reactor. If the jacket temperature is held constant, it implies that the heat transfer rate into the reactor is also constant. However, in most cases, the heat generation or consumption due to the exothermic or endothermic nature of the reaction is not constant. This can lead to a mismatch between the heat input and output, resulting in an unstable reactor temperature.

In this case, we are given the feed rate, composition, and heat capacity of the feed. However, we do not have information about the heat of reaction or any other kinetic parameters. Without this information, we cannot determine the exact stability of the reactor.

Based on the given information, we can conclude that the reactor would not be stable with a constant jacket temperature. To ensure stability, it is necessary to carefully design the heat transfer system, taking into account the heat of reaction and other kinetic parameters. Additional information is needed to perform a more detailed analysis and determine the stability of the reactor.

To know more about reactor , visit;

https://brainly.com/question/29123819

#SPJ11

Temperature is a macroscopic concept that describes the average kinetic energy of a large number of particles in a system.

In the context of a single hydrogen molecule in a heat reservoir, it is not meaningful to define the temperature of the molecule itself. Temperature is a macroscopic concept that describes the average kinetic energy of a large number of particles in a system. It is a statistical property that emerges from the collective behavior of a large ensemble of molecules. However, the Boltzmann distribution, which describes the probabilities of the hydrogen molecule occupying different microstates, is related to temperature. The distribution depends on the energy levels available to the molecule and the temperature of the surrounding reservoir.

By examining the probabilities of different states, we can infer information about the temperature of the reservoir or the average kinetic energy of the ensemble of molecules. Thus, while the temperature of an individual hydrogen molecule is not meaningful, the concept of temperature is applicable to the ensemble of molecules in the system.

To learn more about macroscopic click here: brainly.com/question/2496507

#SPJ11

In Experiment 2, the gas produced at the negative electrode is typically hydrogen (H2).

[tex]\huge{\mathfrak{\colorbox{black}{\textcolor{lime}{I\:hope\:this\:helps\:!\:\:}}}}[/tex]

♥️ [tex]\large{\underline{\textcolor{red}{\mathcal{SUMIT\:\:ROY\:\:(:\:\:}}}}[/tex]

a. The missing reactant for the transformation from benzene to ethylbenzene is ethene (C2H4). b. The missing reactant for the transformation to produce 2-bromo-5-sulfobenzoic acid is 2-bromobenzoic acid.

a. The transformation from benzene to ethylbenzene involves the addition of an ethyl group (C2H5) to the benzene ring. Ethene (C2H4) is a commonly used reactant in this process, and it reacts with a catalyst such as aluminum chloride (AlCl3) to produce ethylbenzene.

b. To synthesize 2-bromo-5-sulfobenzoic acid, the starting material is 2-bromobenzoic acid. The addition of a sulfonic acid group (-SO3H) to the 5th position of the benzene ring is carried out through a sulfonation reaction using sulfuric acid (H2SO4).

The missing reactants for the given transformations have been identified. The transformation from benzene to ethylbenzene requires ethene as a reactant, while the synthesis of 2-bromo-5-sulfobenzoic acid involves starting with 2-bromobenzoic acid. These reactants are crucial for the respective chemical reactions to occur and yield the desired products.

To know more about C2H4 , visit;

https://brainly.com/question/32913572

#SPJ11

To condition the air from 35°C and 70% relative humidity to 20°C and 45% relative humidity, several factors need to be considered. The psychrometric chart is a valuable tool for understanding and analyzing the properties of moist air, such as temperature, humidity, and enthalpy.

a. The plot of the required air conditioning process on the psychrometric chart would show the initial point representing the outside air conditions at 35°C and 70% relative humidity. From there, the process would involve cooling the air to reach the desired temperature of 20°C while reducing the relative humidity to 45%.

b. The amount of water vapor removed can be determined by comparing the initial and final states on the psychrometric chart. It represents the difference in the moisture content (specific humidity) between the two points.

c. The heat removed during the cooling process can be calculated using the formula: Heat removed = mass flow rate of air * specific heat of air * temperature difference.

d. The added heat during the heating process would depend on the desired final temperature of 20°C, the specific heat of air, and the mass flow rate of air. It can be calculated using the formula: Added heat = mass flow rate of air * specific heat of air * temperature difference.

By performing these calculations, one can estimate the amount of water vapor removed, the heat removed, and the added heat necessary to condition the air to the desired conditions.

know more about specific humidity :brainly.com/question/20490622

#SPJ11

The equilibrium composition of the mixture after the reaction between 1 mole of NO and 0.5 mole of O₂ at 700 K and constant pressure will consist of 0.75 mole of NO₂ and 0.25 mole of NO.

The given reaction is:

NO + 0.5O₂ ⇌ NO₂

The equilibrium constant (Ka) for this reaction is 2.0.

To determine the equilibrium composition, we can use the stoichiometry of the reaction and the given initial moles of reactants.

Initially, we have:

- 1 mole of NO

- 0.5 mole of O₂

Let x be the change in moles of NO during the reaction. As the reaction progresses, the moles of NO₂ formed will be equal to x, and the moles of O₂ consumed will be equal to 0.5x.

The equilibrium moles will be:

- NO: 1 - x

- O₂: 0.5 - 0.5x

- NO₂: x

Using the equilibrium constant expression:

Ka = [NO₂] / ([NO] * [O₂])

Substituting the equilibrium moles:

2.0 = x / ((1 - x) * (0.5 - 0.5x))

Solving the equation for x:

2.0 = x / (0.5 - 0.5x)

2.0(0.5 - 0.5x) = x

1.0 - x = x

1 = 2x

x = 0.5

Therefore, at equilibrium, we have:

- NO: 1 - 0.5 = 0.5 mole

- O₂: 0.5 - 0.5(0.5) = 0.25 mole

- NO₂: 0.5 mole

The equilibrium composition of the mixture after the reaction between 1 mole of NO and 0.5 mole of O₂ at 700 K and constant pressure will consist of 0.75 mole of NO₂ and 0.25 mole of NO. This calculation is based on the equilibrium constant and stoichiometry of the reaction, and it provides insights into the composition of the system at equilibrium.

To know more about equilibrium composition, visit

https://brainly.com/question/18849238

#SPJ11

Industrial ecology can help to reduce resource depletion, pollution, and waste generation, and promote economic and social benefits.

BOL Gases plays the role of a decomposer farm in the given scenario by transforming a waste product from the oil refinery into a valuable resource for the Green City buses.

a) i. An industrial ecosystem diagram typically depicts the interconnectedness of various industries, illustrating the flow of resources, energy, and by-products among them.

The diagram showcases the concept of industrial symbiosis, where waste or by-products from one industry become resources for another industry, promoting resource efficiency and reducing environmental impacts.

The benefits of industrial ecology and the triple bottom line (TBL) approach include:

ii. In the given scenario, the company BOL Gases plays the role of a decomposer farm. A decomposer in an industrial ecosystem breaks down and processes waste or by-products from other industries, turning them into valuable resources for further use.

BOL Gases separates, cleans, and pressurizes the hydrogen by-product from the oil refinery, transforming it into purified hydrogen fuel for the Green City buses.

To know more about ecosystem, here:

brainly.com/question/19267717

#SPJ4

The value of the equilibrium constant, K, for the given reaction is 5.65.

The equilibrium constant, K, is defined as the ratio of the product concentrations to the reactant concentrations, each raised to the power of their respective stoichiometric coefficients. Using the given equilibrium concentrations, we can determine the value of K for the reaction.

The balanced equation for the reaction is: 6H₂O (g) + 4CO₂ (g) = 2C₂H₆ (g) + 7O₂ (g)

The expression for the equilibrium constant, K, is: K = ([C₂H₆]^2 * [O₂]^7) / ([H₂O]^6 * [CO₂]^4)

Substituting the given equilibrium concentrations into the expression, we have: K = (0.389^2 * 0.089^7) / (0.256^6 * 0.197^4)

Evaluating the expression, we find: K ≈ 5.65

Therefore, the value of the equilibrium constant, K, for the given reaction is approximately 5.65. This value indicates the position of the equilibrium and the relative concentrations of the reactants and products at equilibrium. A higher value of K suggests a greater concentration of products at equilibrium, while a lower value of K suggests a greater concentration of reactants.

Learn more about equilibrium  : brainly.com/question/30694482

#SPJ11