Assume that you have a wireless application you would like to design,build and sell as a commercial product.You have selected a target frequency in the UHF range.How would you decide what frequency to use and how would you get permission to use it ?

Answers

Answer 1

The frequency to use depends on the range and distance of signal transmission. There is government communication agency in charge of issuing license in order to get carrier frequency in which the application can work with.

UHF means Ultra - high frequencies which is mostly used in television broadcasting and mobile phone. Frequency range of the UHF is between 300MHz to 3GHz.

Assuming that you have a wireless application you would like to design, build and sell as a commercial product. And you have selected a target frequency in the UHF range.

Most wireless applications make use of radio wave and microwave depending on the range of distance in which the signal will travel.

The first thing to do is to determine the distance. Whether is short or long distance.Then get a license from the right  government communication agency so that a carrier wave frequency will be allocated for you.  Determine the side bands frequencies and Calculate the bandwidth

Bandwidth = 2[tex]F_{s}[/tex]

Where [tex]F_{s}[/tex] = sidebands frequency

Purchase all the necessary devices and gadgets like transmitter, oscillator, antenna e.t.c

The bullet points above highlighted how  you can decide what frequency to use and how would you get permission to use it

Learn more here:  https://brainly.com/question/24793150


Related Questions

Identify and explain the importance of Security Information and Event
Management (SIEM) .You are hire as a Information Security officer in Evincible
Securities .And you are going to move organization towards (SIEM) .

Answers

Security Information and events management describes an integration of Information and event management in the aspect of organizational security.

With Security Information and Event Management, organizations can effectively manage security logs of events and information using collected and filtered data in other to identify potential risk to networks and systems in real time.

Gathered information could be used to create threat alerts and assign different level of priority based on specified rules and conditions.

Hence, SIEM could leverage the capability of machine learning models and generated data in other build a robust security system.

Learn more : https://brainly.com/question/25675806

binary classification algorithm

Answers

Answer:

What is this exactly?

Explanation:

If your asking for the definition, binary classification is the task of classifying the elements of a set into two groups on the basis of a classification rule.

As the amplitude decreases in a wave the energy increasesTrue or false

Answers

Answer:

True

Explanation:

To summarise, waves carry energy. The amount of energy they carry is related to their frequency and their amplitude. The higher the frequency, the more energy, and the higher the amplitude, the more energy.

Twisting force is known as: A. thrust.
B. horsepower.
C. torque.
D. energy

Answers

C. Torque. Hope this helps!!!!!!!!

Twisting force is known as:
Select one:
A. thrust.
B. horsepower.
C. torque.
D. energy.

Answers

The correct answer is C. Torque

what is Agriculture and Environmental Engineering ​

Answers

Answer:

Agricultural engineers attempt to solve agricultural problems concerning power supplies, the efficiency of machinery, the use of structures and facilities, pollution and environmental issues, and the storage and processing of agricultural products.

Differentiate between strain hardening exponent and strain rate sensitivity ​

Answers

Whaaaaaaaaaaaaaaaaaaaaaaaaaaatttttttttttttttttttttt

A live load on a house includes the
A.Weight of snow or rain
B.Furnishings
C.Pressure of the earth against the foundation
D.Built-in cabinets

Answers

Answer:

D

Explanation:

For the three-point bending test set up in this lab, what would be the shear force and moment distributions along the beam axis

Answers

Answer:  So to calculate the flexural strength (σ), multiply the force by the length of the sample, and then multiply this by three. Then multiply the depth of the sample by itself (i.e., square it), multiply the result by the width of the sample and then multiply this by two

Explanation:

Anything that is made to meet a need or desire is?
a) Design
b) Technology
c) Process
d) Tool

Answers

Answer:

Technology

Explanation:

It’s made to meet desire

It should be noted that Anything that is made to meet a need or desire is Technology.

What is Technology?

Technology can be regarded as the practical application of science.

Technology can be seen in areas such as

CommunicationTransportationAgriculture

However, Technology came up because of the necessity for it, people desire it.

Learn more Technology at;

https://brainly.com/question/25110079

Read an integer from the user repeatedly, until the user enters a negative number. use for loop (C programming)​

Answers

Answer:

go on then

Explanation:

The following problem refers to triangle ABC, find all missing parts. Round degrees to 1 decimal places and
sides to the nearest whole number.
A = 36.5°C = 67.5°, c = 224 inches
A=
В.
C
O
O
490 do
a =
inches
inches
inches
C-

Answers

Answer:

A =41 .....

......

......

....C=21

Engineer It A water heater is a tank in which cold water is heated. Cold water flows into the tank to keep it full. A heating element warms the water inside the tank. The heated water can then be sent to hot water faucets in a building. Assume that a water heater design requires the hottest water possible to be sent to hot water faucets in a building. Where would be the best place for the hot water outlet pipe to be attached to the tank: the top, the middle, or the bottom of the tank? Explain your answer.

Answers

Answer:

i think it would be the top, the hotter the water the more pressure and sense pressure builds at the top of water heater tanks you would want the outlet pipe at the top

Explanation:

I think it would be the top, the hotter the water the more pressure and sense pressure builds at the top of water heater tanks you would want the outlet pipe at the top.

What is Heater?

The process of transforming electrical current into heat energy is known as electric heating. An electrical resistor serves as the heating element in an electric heater, and heat is generated there when an electric current flows through it.

This procedure is frequently utilized in a wide range of domestic applications. from using an electric burner to prepare food, a kettle to boil water, and of course, house heating.

With one significant exception—they don't rely on a boiler and a system of pipes to produce the heat—electric heaters and radiators function exactly like your central heating radiators that are plumbed in.

Therefore, I think it would be the top, the hotter the water the more pressure and sense pressure builds at the top of water heater tanks you would want the outlet pipe at the top.

To learn more about Heating, refer to the link:

https://brainly.com/question/1429452

#SPJ2

qué es una nube informática

Answers

Es un paradigma que permite ofrecer servicios de computación a través de una red, que usualmente es internet.

10. "PPE is the control of last resort." What does this mean?

Answers

Answer:

protect the employee once the hazard into contact with them.


Write an
algorithm and draw a flowchart to convert the length in feet to
centimeter

Answers

Answer:

blah blah blah sh ut up read learn

As
is the rate (in time and distance) at which that force
is a twisting or turning force,
is produced
(
Select one:
O A. Torque; horsepower; torque
OB. Torque; horsepower; horsepower
O C. Horsepower; torque; horsepower
O D. Horsepower; torque; torque
Clear my choice

Answers

Answer:

C

Explanation:

As horsepower is the rate  at which that force torque  is a twisting or turning force, horsepower is produced. Hence option  C is correct.

What is horsepower?

Horsepower is defined as a unit used to describe the pace at which labor is done or to quantify power, frequently in relation to the output of engines or motors. Standardization and types of horsepower vary widely. A car's engine power is measured in horsepower (hp); the greater the number, the more power is transferred to the wheels and, in theory, the faster it will travel.

To put it simply, horsepower is your overall speed and power, whereas torque allows you to feel the sensation of acceleration when you put your foot down. When you realize that horsepower is derived from torque, this makes sense. Torque is a unit of rotational or twisting force. The power an engine produces is referred to as horsepower.

Thus, as horsepower is the rate  at which that force torque  is a twisting or turning force, horsepower is produced. Hence option  C is correct.  

To learn more about horsepower, refer to the link below:

https://brainly.com/question/12260337

#SPJ2

A nut driver is a variation of a socket wrench, true?

Answers

Answer:

TRUE

Explanation:

Answer: True

Explanation: Nut drivers are sockets that can be snapped on or permanently fixed to a screwdriver-type handle.

Discuss on forced convection heat transfer with real examples.

Answers

Answer:

forced convection

Explanation:

When a fan, pump or suction device is used to facilitate convection, the result is forced convection. Everyday examples of this can be seen with air conditioning, central heating, a car radiator using fluid, or a convection oven.

explain the sphere gap method of measuring dc ac and impulse voltages

Answers

Answer:

The voltage to be measured is applied between the two spheres and the distance or spacing S between them gives a measure of the sparkover voltage. ... In the case of a.c. peak value and d.c. voltage measurements, the applied voltage is uniformly increased until sparkover occurs in the gap.

Using what you know about the NAND gate, draw how you could implement a three-input NAND gate using NMOS and PMOS transistors. This circuit should output logic low (0V) only when all three inputs (A, B, and C) are logic high (5V)

Answers

Answer:

use this, it should help you understand

Explanation:

https://www.electronics-tutorials.ws/logic/logic_5.html

pretty ako hjshjs ok.

Answers

Answer:

wala naman pong pic po wala kahit walang pic magan da parin

Concrete is forced into all parts of its form through a process called?

Answers

Concrete is forced into all parts of its form through a process called hydration.

What is hydration of concrete?

The concrete is known to be one that solidifies and also hardens via a chemical method known to be hydration.

This is when water reacts with the cement, and it is one that bonds the other components together and so Concrete is forced into all parts of its form through a process called hydration.

Learn more about hydration from

https://brainly.com/question/5060579

#SPJ1

In the figure, particle 1 of mass m1 = 3.1 kg slides rightward along an x axis on a frictionless floor with a speed of 5.0 m/s. When it reaches x = 0, it undergoes a one-dimensional elastic collision with stationary particle 2 of mass m2 = 4.6 kg. When particle 2 then reaches a wall at xw = 79 cm, it bounces from the wall with no loss of speed. At what position on the x-axis does particle 2 then collide with particle 1?

Answers

Answer:

We use Eq 9−67 and 9−68 to find the velocities of the particles after their first collision (at x=0 and t=0 )

ν

1f

m

1

+m

2

m

1

+m

2

ν

1i

=

0.30kg+0.40kg

0.30kg−0.40kg

(2.0m/s)=−0.29m/s

ν

2f

=

m

1

+m

2

2m

1

ν

1i

=

0.30kg+0.40kg

2(0.30kg)

(2.0m/s)=1.7m/s .

At a rate of motion of 1.7m/s,2x

w

=140cm (the distance to the wall and back to x=0 ) will be traversed by particle 2 in 0.82s . At t=0.82s , particle 1 is located at

x=(−2/7)(0.82)=−23cm ,

and particle 2 is " gaining " at a rate of (10/7)m/s leftward ; this is their relative velocity at that time . Thus , this "gap" of 23cm between them will be closed after an additional time of (0.23m)/(10/7m/s)=0.16s has passed . At this time (t=0.82+0.16=0.98s) the two particles are at x=(−2/7)(0.98)=−28cm

Explanation:

The process of refining specification involves
O defining the initial design.
O presenting the finished product to a client.
deciding whether or not to continue with a project.
O adjusting outcomes and making pragmatic changes.

Answers

Answer:

I'm not sure but I'm pretty sure it the second one (btw I'm sorry if this didn't help) :/

Warning danger ahead sign

Answers

Answer: okiiiii

Explanation:

Answer

Ok

Explanation

variable head permeability ?

Answers

Answer:

The variable head permeability test is one of various methods for determining soil permeability. It is used to determine the permeability of relatively new soil. Permeability refers to a soil's ability to enable water to pass through its pores or spaces.

Explanation:

List the crops that can be used dibbler .

Answers

Answer:

A dibber or dibble or dibbler

Explanation:

A dibber or dibble or dibbler is a pointed wooden stick for making holes in the ground so that seeds, seedlings or small bulbs can be planted. Dibbers come in a variety of designs including the straight dibber, T-handled dibber, trowel dibber, and L-shaped dibber

Technician A states that about 33% of the heat energy created is wasted by being dumped straight out
of the exhaust to the atmosphere. Technician B states that 33% is wasted by internal friction and from
radiating off hot engine components straight to the atmosphere. Who is correct?
Select one:
A. Technician A
B. Technician B
C. Both A and B
D. Neither Anor B

Answers

Heat energy is the known to be a product of the movement of tiny particles called atoms, molecules or ions. The true statement is by Technician A.

Internal combustion engine is dependent on the heat of combustion so as to make torque to move the vehicle and power the system.

A lot of heat made during combustion is not often used productively and therefore need to be removed to avoid overheating of the engine.

The heat energy that is not used for is wasted in three ways: They are:

About 33% is wasted by being dumped straight out of the exhaust to the atmosphere. About 33% is wasted by the cooling system, which prevents overheating of the engine components. About 5% is wasted by internal friction and from radiating off of hot engine components straight to the atmosphere.

Learn more from

https://brainly.com/question/14566159

What is the purpose of the red-core yarns in the synthetic sling?

Answers

An immediate strength loss. This is why Sling Webbing has red core yarns to visually reveal damage and act as a basis for sling rejection.

▞▞<☵>▆▇█▓▒­░─╤╦╱彡( ⱫɆ₳Ⱡ )彡╲╦╤─░▒▓▇▆▅<☵>▞▞

The  purpose of the red-core yarns in the synthetic sling is to detect the strength loss and also to reveal the damage in the red corn yarns.

What is synthetic sling?

Lifting slings constructed of synthetic materials like nylon or polyester are known as synthetic slings. These kinds of slings, which can also be called synthetic lifting straps or synthetic rigging slings, are thin, flexible, and protected by a jacket.

Sling Webbing features red core yarns to visibly indicate damage and serve as a reason for sling rejection because of this.  Synthetic sling are flexible.

Therefore, it can be concluded that The red-core yarns in the synthetic sling are used to both reveal and detect strength loss in the red maize yarns. It also acts as the basis for sling rejection.

Learn more about Synthetic sling here:

https://brainly.com/question/27088476

#SPJ2

Other Questions
Solve for y.6y - 2x = 20Simplify fractions completely.[?]y == 4x + 1+Enter What factors make capital appreciation bonds (CABs) a controversial method for local governments to finance projects Reinhart discusses making an epoxy of sorts in terms of bread. The first part of the epoxy is whole grain bread. What is the second part he talks about?please help me out !! How much Ba(OH)2, in grams, is needed to make a 1.00m aqueous solution? Could someone explain how to convert from slope intercept form: y=mx+b to standard form: ax+by=c because I dont understand Dont copy from the internet pls who believed that our personality traits are influenced write a paragraph about the game you like the most How is a scale model different from other types of models?It is made with clay.It includes many engineers' ideas.It maintains correct spatial relations.It is the last type of godel created in the design process im kind of lazy how many days till november 21st? 25 point bible questionThe beast and the false prophet were thrown into a lake of fire during the seven _____.trumpetsjudgementssealswonders A freight train 22.5 miles per 60 miles to its destination how far from the destination will the train be in 2.5 hour How would you best describe the angle pair In agranulocytes, what happens to the cytoplasm as the cell ages? I need some help with this one I'm lost! The students became interested in investigating the properties of carbon dioxide gas at extreme pressures and temperatures. However, they noticed that the state diagram provided to them did not extend to such extreme conditions. Based on the provided state diagram, which of the following extreme pressures and temperatures is carbon dioxide gas most likely to exist as?A. 500 kPa and 1000B. 500 kPa and -1000C. 50,000 kPa and -1000D. Carbon dioxide cannot exist at extreme conditions. Choisissez from VHL Central After the Election of 1860, why did members of the U.S. Senate quickly form a compromise committee? The temprature at which a solid melts is the same as the temprature at which its luqid form solidifies.TRUE OR FALSE.PLS GUYS HELP ME! Plzzzz help meeee plzzzz Read the following passage from Mark Twain's "The War Prayer":[F]or our sakes who adore Thee, Lord, blast their hopes,blight their lives, protract their bitter pilgrimage, makeheavy their steps, water their way with their tears, stain thewhite snow with the blood of their wounded feet!Which rhetorical device is demonstrated in this passage?A) PolysyndetonB) Anaphora C) PolyptotonD) Asyndeton