Momentum is conserved in a system of objects when the forces external to the system are zero and the internal forces sum to zero, according to Newton's Third Law.
This conservation law is fundamental to the study of physics. Momentum conservation arises from Newton's Third Law, which states that for every action, there is an equal and opposite reaction. When the sum of the external forces on a system is zero, there is no net external impulse, and hence, the total momentum of the system remains constant. The internal forces, due to Newton's Third Law, will always be in pairs of equal magnitude and opposite directions, thereby canceling out when summed. This leaves the total momentum of the system unchanged. The other options, including those involving conservative forces, and the sum of momentum vectors equaling zero, do not necessarily lead to momentum conservation.
Learn more about the conservation of momentum here:
https://brainly.com/question/32097662
#SPJ11
What is the reasons that called the capacitor is an ideal parallel plate capacitor?
The reasons for calling a capacitor an ideal parallel plate capacitor are: (1) It assumes infinite plate area, resulting in uniform electric field between the plates; (2) It assumes no dielectric or conducting material between the plates, minimizing losses and fringing effects.
An ideal parallel plate capacitor is a theoretical concept used to simplify the analysis of real-world capacitors. It is called "ideal" because it assumes certain conditions that may not be fully achievable in practice. The key reasons for labeling it as an ideal parallel plate capacitor are as follows.
Firstly, it assumes infinite plate area. This assumption implies that the plates are infinitely large, ensuring a uniform electric field between them. In reality, the plates of a capacitor have finite dimensions, leading to non-uniform electric fields near the edges, known as fringing effects. However, by assuming infinite plate area, these edge effects are disregarded, simplifying the analysis.
Secondly, the ideal parallel plate capacitor assumes no dielectric or conducting material between the plates. This assumption eliminates losses due to dielectric absorption or leakage currents, which can occur in real capacitors. In practice, capacitors employ dielectric materials between the plates to enhance capacitance, but these materials may introduce non-ideal characteristics.
While an ideal parallel plate capacitor serves as a useful theoretical model, real-world capacitors deviate from these assumptions. Factors like finite plate area, dielectric properties, and parasitic effects influence the behavior of practical capacitors. Nonetheless, the ideal parallel plate capacitor provides a valuable starting point for understanding the fundamental principles of capacitance and energy storage.
To know more about Capacitors click here:
https://brainly.com/question/31627158
#SPJ11
Read the following statements regarding electromagnetic waves traveling in a vacuum. For each statement, write T if it's true and F if it's false. [conceptual (a) Tor F All waves have the same wavelength (b) T or F All waves have the same frequency (C) T or F All waves travel at 3.00 x 108 m/s (d) T or F The electric and magnetic fields of the waves are perpendicular to each other and to the direction of motion of the wave (e) T or F The speed of the waves depends on their frequency
Statement a is FALSE , Statement B is FALSE , Statement c is TRUE , Statement D is TRUE , Statement e is FALSE
(a) The statement "All waves have the same wavelength" is false. Different waves can have different wavelengths. Wavelength refers to the distance between two consecutive points of a wave that are in phase with each other.
(b) The statement "All waves have the same frequency" is false. Waves can have different frequencies. Frequency refers to the number of complete cycles of a wave that occur in one second.
(c) The statement "All waves travel at 3.00 x 10^8 m/s" is true. In a vacuum, electromagnetic waves, including light, travel at the speed of light, which is approximately 3.00 x 10^8 m/s.
(d) The statement "The electric and magnetic fields of the waves are perpendicular to each other and to the direction of motion of the wave" is true. Electromagnetic waves consist of electric and magnetic fields oscillating perpendicular to each other and to the direction of wave propagation.
(e) The statement "The speed of the waves depends on their frequency" is false. The speed of electromagnetic waves, such as light, is constant in a vacuum and does not depend on their frequency. All electromagnetic waves in a vacuum travel at the same speed, regardless of their frequency or wavelength.
Learn more about waves here :
https://brainly.com/question/16263433
#SPJ11
Three resistors are connected in parallel. If their respective resistances are R1 = 23.0 Ω, R2 = 8.5 Ω and R3 = 31.0 Ω, then their equivalent resistance will be: a. 5.17 Ω
b. 62.5 Ω
c. 0.193 Ω
d. 96.97 Ω
The equivalent resistance of the three resistors connected in parallel is 5.17 Ω.
The equivalent resistance of the three resistors that are connected in parallel is calculated as follows:
The formula for calculating the equivalent resistance for resistors in parallel is given as:
1/Rp = 1/R1 + 1/R2 + 1/R3 +...+ 1/Rn
where Rp is the equivalent resistance, and R1, R2, R3 and so on are the resistances in ohms.
The values of resistances are given as:
R1 = 23.0 Ω
R2 = 8.5 Ω
R3 = 31.0 Ω
Substitute the given values of resistances into the equation:
1/Rp = 1/23.0 + 1/8.5 + 1/31.0
1/Rp = 0.043 + 0.118 + 0.032
1/Rp = 0.193
To find the equivalent resistance, we take the reciprocal of both sides of the equation:
Rp = 1/0.193
Rp = 5.18 Ω
Learn more about resistances: https://brainly.com/question/24119414
#SPJ11
Analyze the operating principles and applications for any ONE (1) of the turbines listed below with appropriate sketches or diagrams: [Analisakan prinsip dan aplikasi operasi untuk mana-mana SATU (1) daripada turbin yang disenaraikan dihawah dengan lakaran atau gambar rajah yang sesuai:] (i) Kaplan turbine. [Turbin Kaplan.] (ii) Francis turbine. [Turbin Francis.] (iii) Pelton turbine. [Turbin Pelton.] (4 Marks/ Markah)
Operating Principles: The Francis turbine is a type of reaction turbine used for converting the energy of flowing water into mechanical energy. It is specifically designed to operate with medium to high head and medium flow rates.
The key operating principles of the Francis turbine include:
1. Water Inlet: The water enters the turbine through a spiral-shaped casing known as the scroll case or volute. The scroll case gradually distributes the water uniformly around the circumference of the runner.
2. Runner: The runner consists of a set of curved blades or vanes that are fixed to a central hub. These blades are designed to efficiently harness the kinetic energy of the water and convert it into rotational mechanical energy.
3. Guide Vanes: The guide vanes are adjustable blades located in the casing just before the water enters the runner. They control the flow of water and direct it onto the runner blades at the desired angle, optimizing the turbine's performance.
4. Water Flow and Pressure: As the water passes through the runner blades, it undergoes a change in direction, creating a pressure difference across the blades. The pressure difference generates a force on the blades, causing them to rotate.
5. Shaft and Generator: The rotational motion of the runner is transmitted to a shaft connected to a generator. The generator converts the mechanical energy into electrical energy, which can be used for various applications.
Applications:
1.The Francis turbine is widely used in hydroelectric power plants due to its versatility and efficiency. It is suitable for both high head and medium head applications. Here are some of its applications:
2. Hydroelectric Power Generation: Francis turbines are commonly used in hydroelectric power plants to generate electricity. They are ideal for sites where the head of water is between 10 and 600 meters, and the flow rate is moderate.
3. Irrigation Systems: The Francis turbine can be employed in irrigation systems to drive pumps or lift water from a lower level to a higher level. It can efficiently harness the energy from water sources such as rivers, canals, or reservoirs.
4 .Pumped Storage Systems: In pumped storage power plants, excess electricity is used to pump water from a lower reservoir to an upper reservoir during periods of low demand. The Francis turbine is then used in reverse as a pump to release the stored water, generating electricity during peak demand periods.
5. Industrial Applications: Francis turbines can also be used in various industrial applications that require mechanical energy, such as powering large fans, compressors, or mills.
Overall, the Francis turbine is a versatile and efficient device used for converting the energy of flowing water into mechanical energy. Its adaptability to different head and flow conditions makes it a preferred choice for hydroelectric power generation and other water-driven applications.
To know more about Turbines visit:
https://brainly.com/question/11966219
#SPJ11
Trie or Fafse: When an object is moving slower than 1% of the speed of light, Elnstein's Theory of Relativity would be the best tool to use to analyze the motion of the object. True False
The given statement is false and special relativity is not the best tool to use to analyze the motion of the object if the object is moving slower than 1% of the speed of light. Hence, this statement is False.
Trie or False: When an object is moving slower than 1% of the speed of light, Elnstein's Theory of Relativity would be the best tool to use to analyze the motion of the object. The given statement is FALSE. This statement contradicts Einstein's theory of relativity.The theory of relativity is divided into two parts, special relativity and general relativity.
Both theories work best in different situations. Special relativity explains the relationship between space and time, whereas general relativity describes the relationship between matter, gravity, and spacetime.In general relativity, when an object moves at a high speed or in a strong gravitational field, its motion can be analyzed accurately using this theory.
At low speeds or without a strong gravitational field, general relativity is not required to analyze the motion of an object.Einstein's theory of special relativity is more accurate and reliable than classical mechanics to analyze the motion of an object moving close to the speed of light, but it is not required to analyze the motion of an object moving slower than 1% of the speed of light.
Hence the given statement is false and special relativity is not the best tool to use to analyze the motion of the object if the object is moving slower than 1% of the speed of light. Hence, this statement is False.
Learn more about gravitational field here,
https://brainly.com/question/28437652
#SPJ11
R= 8.31 J/mol K kb = 1.38 x 10-23 J/K 0°C = 273.15 K NA = 6.02 x 1023 atoms/mol Density of Water, p=1000 kg/m? Atmospheric Pressure, P. = 101300 Pa g= 9.8 m/s2 1. 100 g of Argon gas at 20°C is confined within a constant volume at atmospheric pressure Po. The molar mass of Argon is 39.9 g/mol. A) (10 points) What is the volume of the gas? B) (10 points) What is the pressure of the gas if it is cooled to -50°C? 2. A small building has a rectangular brick wall that is 5.0 m x 5.0 m in area and is 6.0 cm thick. The temperature inside the building is 20 °C and the outside temperature is 5 °C. The thermal conductivity for brick = 0.84 W/(m. C). A) (10 points) At what rate is heat lost through the brick wall? B) (10 points) A 4.0 cm thick layer of Styrofoam, with thermal conductivity = 0.010 W/(m. C°), is added to the entire area of the wall on the inside of the building. If the inside and outside temperatures are the same as in Part A, what is the temperature at the boundary between the Styrofoam and the brick?
1. Given
R= 8.31 J/mol K
kb = 1.38 x 10-23 J/K0°C = 273.15 KNA = 6.02 x 1023 atoms/mol
Density of Water, p=1000 kg/m³
Atmospheric Pressure, P = 101300 Pa
g= 9.8 m/s²
We know that PV = nRTOr
V = (nRT)/PN = given mass/molar mass
= 100/39.9
= 2.5063 moles
V = (2.5063 mol x 8.31 J/mol K x (20 + 273.15) K)/101300
Pa= 0.50 m³At -50°C or 223.15 K,
V = nRT/PV = 2.5063 mol x 8.31 J/mol K x 223.15 K/0.50 m³ x 1.38 x 10-23 J/K= 8.83 x 105 Pa
Therefore, the volume of gas at 20°C is 0.50 m³, and the pressure of gas at -50°C is 8.83 × 10⁵ Pa.2.
Given Area of the wall,
A = 5.0 m x 5.0 m = 25.0 m²
Thickness of the wall, L = 6.0 cm = 0.06 m
Temperature inside the building, Ti = 20°C = 293.15 K
Temperature outside the building, To = 5°C = 278.15 K
Thermal conductivity of brick, k = 0.84 W/(m·K)
Thermal conductivity of Styrofoam, k` = 0.010 W/(m·K)
A) Heat lost through the brick wall
Rate of heat transfer through the brick wall is given byQ = k A (Ti - To) / L= 0.84 W/(m·K) x 25.0 m² x (20 - 5) K / 0.06 m= 7.00 x 10⁴ W or 70 kW.
B) Temperature at the boundary between the Styrofoam and the brick wallLet
T be the temperature at the boundary between the Styrofoam and the brick wall.
Q = k A (Ti - T) / L1 + Q = k` A (T - To) / L2So (k A / L1) Ti - (k A / L1 + k` A / L2) T + (k` A / L2) To = 0On
solving this equation, we getT = (k` A / L2) To / (k A / L1 + k` A / L2)= (0.010 W/(m·K) x 25.0 m² x 278.15 K) / (0.84 W/(m·K) / 0.06 m + 0.010 W/(m·K) / 0.040 m)= 282.22 K = 9.07 °C
Therefore, the temperature at the boundary between the Styrofoam and the brick wall is 9.07 °C.
Learn more about heat transfer, here
https://brainly.com/question/16055406
#SPJ11
A hunter spots a duck flying a given distance, h, above the ground (in meters) and shoots at it with his shotgun. The buckshot leaves the shotgun at an angle equal to 45.1 degrees from the horizontal with a velocity of 103 m/s. The duck is flying at a speed of 30 m/s in a horizontal direction toward the hunter. If the hunter shot when the duck was 200 meters away from the hunter and hit the duck, how high was the duck flying?
Given data:
Distance between duck and hunter, s = 200 m
Velocity of the bullet, u = 103 m/s
Velocity of the duck, v = 30 m/s
Angle made by the gun from horizontal, θ = 45.1°
We have to find the height at which the duck was flying,
h.
Let's begin with calculating the time taken by the bullet to reach the duck using the horizontal component of the velocity of the bullet. Distance covered by the bullet, S = vt
Where, t is the time taken to reach the duck.
The distance covered by the duck is also s = vt.
It implies that the time taken by the bullet and the duck to reach the point of collision is the same.
Therefore,
t = s/v = 200/30 = 6.67 s
Now, using the vertical component of velocity of the bullet, we can calculate the height at which the duck was flying.
u = v₀ + gtv₀ = usinθ
where g = 9.8 m/s², and v₀ is the initial vertical component of velocity of the bullet.
v₀ = u sin θ = 103 × sin 45.1°
= 73.09 m/s
Now, the height of the duck, h = v₀t + (1/2)gt²h
= (73.09 × 6.67) + (1/2) × 9.8 × (6.67)²
= 487.67 + 223.18
= 710.85 m
Therefore, the duck was flying at a height of 710.85 meters above the ground.
Learn more about The horizontal and vertical components here
https://brainly.com/question/24681896
#SPJ11
Two identical balls of putty moving perpendicular to each other, both moving at 6.45 m/s, experience a perfectly inelastic collision. What is the speed of the combined ball after the collision? Give your answer to two decimal places
The speed of the combined ball after the collision is 6.45 m/s.
In this case, the two identical balls of putty moving perpendicular to each other, both moving at 6.45 m/s experience a perfectly inelastic collision. The goal is to determine the speed of the combined ball after the collision.
To solve for the speed of the combined ball after the collision, we can use the formula for the conservation of momentum, which is:
m1v1 + m2v2 = (m1 + m2)v
where
m1 and m2 are the masses of the two identical balls of putty,
v1 and v2 are their initial velocities,
v is their final velocity after the collision
Since the two balls have the same mass, we can simplify the equation to:
2m × 6.45 m/s = 2mv
where
v is the final velocity after the collision,
2m is the total mass of the two balls of putty
Simplifying, we get:
12.90 m/s = 2v
Dividing both sides by 2, we get:
v = 6.45 m/s
Therefore, the speed of the combined ball after the collision is 6.45 m/s.
Learn more about speed:
https://brainly.com/question/13943409
#SPJ11
material and energy balance equations for an unsteady
compressible flow in Cartesian coordinates
In an unsteady compressible flow in Cartesian coordinates, material and energy balance equations are used to describe the conservation of mass and energy within the system. These equations are commonly referred to as the continuity equation and the energy equation, respectively.
Continuity Equation:
The continuity equation for an unsteady compressible flow in Cartesian coordinates can be expressed as:
∂ρ/∂t + ∂(ρu)/∂x + ∂(ρv)/∂y + ∂(ρw)/∂z = 0
where:
ρ is the density of the fluid,
t is the time,
u, v, and w are the components of velocity in the x, y, and z directions, respectively, and
x, y, and z are the Cartesian coordinates.
This equation represents the conservation of mass and states that the rate of change of density within a control volume, together with the divergence of the mass flux in each direction, must sum to zero.
Energy Equation:
The energy equation for an unsteady compressible flow in Cartesian coordinates can be expressed as:
∂(ρe)/∂t + ∂(ρeu)/∂x + ∂(ρev)/∂y + ∂(ρew)/∂z = -∇•(pu) + ∂(τu)/∂x + ∂(τv)/∂y + ∂(τw)/∂z + Q
where:
e is the specific internal energy of the fluid,
p is the pressure,
τ is the stress tensor,
Q is the heat transfer per unit volume,
and other terms have the same meaning as in the continuity equation.
This equation represents the conservation of energy and states that the rate of change of energy within a control volume, together with the work done by pressure forces, heat transfer, and viscous effects, must sum to zero.
These material and energy balance equations provide a mathematical framework for analyzing and predicting the behavior of unsteady compressible flows in Cartesian coordinates. They are essential tools in fields such as fluid dynamics, aerodynamics, and thermodynamics for understanding the flow and energy exchange processes within a system.
Learn more about fluid dynamics here:
https://brainly.com/question/30578986
#SPJ11
The magnetic field flux through a circular wire is 60 Wb. The radius of the wire is duplicated over the course of 3 s. Determine the voltage that is generated in that interval.
The voltage that is generated in 3 seconds will be N × πr²/2 × (4πRB - 60 / 3) where r → r' and the given magnetic field flux through a circular wire is 60 Wb.
The magnetic field flux through a circular wire is 60 Wb.
Radius of wire is duplicated over the course of 3 seconds.i.e, Radius initially, r = R
New radius, r' = 2R
Time taken, t = 3 s
We have to find out the voltage generated in this interval.Formula to find out the voltage generatedV = N × A × (dΦ / dt)
Where, N is the number of turns A is the area of the loopd Φ is the change in magnetic flux in timet is the time taken by the change in magnetic flux to occuri.e, V = N × A × (dΦ / dt)
We have a circular wire. So, the area of the loop is,A = πr²
When radius changes, i.e, r → r',dA = πr² - πr²/2= πr²/2
So, the voltage generated will be,V = N × A × (dΦ / dt)= N × πr²/2 × [(Φ' - Φ) / t]
Here, initial flux, Φ = 60 Wb
Final flux, Φ' = Φ at t = 3 s = π(2R)²×B = π(4R²)B
Now, the voltage generated will be V = N × πr²/2 × [(Φ' - Φ) / t]= N × πr²/2 × [(π(4R²)B - 60) / 3]= N × πr²/2 × (4πRB - 60 / 3)
Therefore, the voltage that is generated in 3 seconds will be N × πr²/2 × (4πRB - 60 / 3) where r → r' and the given magnetic field flux through a circular wire is 60 Wb.
Know more about voltage here,
https://brainly.com/question/31347497
#SPJ11
If when an object is placed 20 cm in front of a mirror the image is located 13.6 cm behind the mirror, determine the focal length of the mirror.
The object is placed 20 cm in front of a mirror and the image is located 13.6 cm behind the mirror.
The formula for the focal length of a mirror is given by;
`1/f = 1/di + 1/do` Where, `f` is the focal length of the mirror, `di` is the distance of the image from the mirror, and `do` is the distance of the object from the mirror.
The given values are: `di = -13.6 cm` (negative sign indicates that the image is formed behind the mirror) `do = -20 cm` (negative sign indicates that the object is placed in front of the mirror) `f` is the unknown.
Let's substitute the given values in the formula.
`1/f = 1/di + 1/do`
`1/f = 1/-13.6 + 1/-20`
`1/f = -0.0735 - 0.05`
`1/f = -0.1235`
`f = 1/-0.1235`= -8.097
Therefore, the focal length of the mirror is approximately 8.1 cm.
Learn more about the focal length of lenses: https://brainly.com/question/1031772
#SPJ11
57 .. A small plane departs from point A heading for an air- port 520 km due north at point B. The airspeed of the plane is 240 km/h and there is a steady wind of 50 km/h blowing directly toward the southeast. Determine the proper heading for the plane and the time of flight. SSM 1/- سامد - )
The plane's heading should be approximately 13 degrees east of north, and the time of flight will be 2.28 hours.
To determine the proper heading for the plane, we need to consider the effect of the wind on its trajectory. Since the wind is blowing directly toward the southeast, it will create a force that opposes the plane's northward motion. We can break down the wind velocity into its northward and eastward components using trigonometry.
The northward component will be 50 km/h multiplied by the sine of 45 degrees, resulting in a value of approximately 35.4 km/h. Subtracting this from the plane's airspeed of 240 km/h gives us an effective northward velocity of approximately 204.6 km/h.
Next, we can use this effective northward velocity to calculate the time of flight. Dividing the distance between points A and B (520 km) by the effective northward velocity (204.6 km/h) gives us approximately 2.54 hours. However, we need to account for the wind's eastward force.
The eastward component of the wind velocity is 50 km/h multiplied by the cosine of 45 degrees, which is approximately 35.4 km/h. Multiplying this by the time of flight (2.54 hours) gives us an eastward distance of approximately 90 km. Subtracting this eastward distance from the total distance traveled (520 km) gives us the northward distance covered by the plane, which is approximately 430 km. Finally, dividing this northward distance by the effective northward velocity gives us the corrected time of flight, which is approximately 2.28 hours.
Learn more about wind velocity here:
https://brainly.com/question/8486728
#SPJ11
Milan is wearing a life jacket and is being circled by sharks in the ocean and notices that after a wave crest passes by, ten more crests pass in a time of 120s. What is the period of the wave? T: 2
Milan is wearing a life jacket and is being circled by sharks in the ocean, the period of the wave is 12 seconds.
In this scenario, Milan is observing waves in the ocean while wearing a life jacket. Milan notices that after a wave crest passes by, ten more crests pass in a time of 120 seconds.
To determine the period of the wave, we need to consider the number of wave crests that pass by in a given time interval. In this case, Milan observes that ten wave crests pass by in a time of 120 seconds.
The period of a wave is defined as the time it takes for one complete wave cycle to occur. Since Milan observes that ten wave crests pass by in 120 seconds, we can calculate the period of each wave by dividing the total time by the number of wave crests:
Period of each wave = Total time / Number of wave crests
Period of each wave = 120 seconds / 10 = 12 seconds
Therefore, the period of the wave is 12 seconds.
It's important to note that the term "T: 2" mentioned in the question does not have a clear meaning in the given context. The period of the wave is determined as 12 seconds based on the information provided.
Learn more about wave crests here:
https://brainly.com/question/31823225
#SPJ11
An electromagnetic wave in the visible spectrum has a wavelength of 675 nm and a frequency of 5.0×10 15
Hz
4.4×10 14
Hz
4.4×10 6
Hz
1.2×10 5
Hz
1.2×10 14
Hz
The only valid representation of an electromagnetic wave in the visible spectrum among the given options is a wavelength of 675 nm and a frequency of 4.4×10^14 Hz. So, the correct answer is 4.4×10^14 Hz.
1. A wavelength of 675 nm and a frequency of 5.0×10^15 Hz:
This combination is not valid because the speed of light is approximately 3.0×10^8 m/s, which is a constant in a vacuum. If we calculate the speed of light using the equation v = λf, where v is the speed of light, λ is the wavelength, and f is the frequency, we get a speed of light much higher than the actual value. Therefore, this option is incorrect.
2. A wavelength of 675 nm and a frequency of 4.4×10^14 Hz:
This combination is valid and falls within the visible spectrum. The given wavelength corresponds to a color between red and orange. The frequency represents the number of oscillations per second for the electromagnetic wave. Therefore, this option is a valid representation of an electromagnetic wave in the visible spectrum.
3. A wavelength of 675 nm and a frequency of 4.4×10^6 Hz:
This combination is not valid because the frequency is extremely low for visible light. Visible light waves have frequencies typically ranging from 4.3×10^14 Hz (violet) to 7.5×10^14 Hz (red). Therefore, this option is incorrect.
4. A wavelength of 675 nm and a frequency of 1.2×10^5 Hz:
This combination is not valid because the frequency is extremely low for visible light. As mentioned earlier, visible light waves have frequencies typically ranging from 4.3×10^14 Hz (violet) to 7.5×10^14 Hz (red). Therefore, this option is incorrect.
5. A wavelength of 675 nm and a frequency of 1.2×10^14 Hz:
This combination is not valid because the frequency is still too low for visible light. As mentioned earlier, visible light waves have frequencies typically ranging from 4.3×10^14 Hz (violet) to 7.5×10^14 Hz (red). Therefore, this option is incorrect.
In summary, the only valid representation of an electromagnetic wave in the visible spectrum among the given options is a wavelength of 675 nm and a frequency of 4.4×10^14 Hz.
Learn more about electromagnetic wave
https://brainly.com/question/22058311
#SPJ11
2.Two currents 5 - j2 amperes and 3 - j 2 amperes enter a
junction. What is the outgoing currents given voltage 220 V ac
source at 60 hertz frequency.
please help. thanks
The outgoing current from the junction can be calculated by summing the incoming currents. In this case, the outgoing current would be 8 - j4 amperes.
To calculate the outgoing current from the junction, we need to add the two incoming currents. Given that one current is 5 - j2 amperes and the other is 3 - j2 amperes, we can simply add the real and imaginary components separately.
For the real component, we add 5 and 3, resulting in 8 amperes. For the imaginary component, we add -j2 and -j2, which gives us -j4 amperes.
Thus, the outgoing current from the junction is 8 - j4 amperes. This means that the current leaving the junction has a real component of 8 amperes and an imaginary component of -4 amperes. The direction and phase of the current would depend on the specific circuit configuration and the voltage source.
To know more about outgoing current click here:
https://brainly.com/question/17198579
#SPJ11
Come up with a simple equation describing the total surface energy balance at any one point on the Earth. Set it up like a mass balance equation where on one side you include all energy sources and the other side is all of the places where the energy is dissipated. In my notes, I denote Q* as total energy, QH as sensible heat, QE as latent heat, etc. You can designate advection with an A, if you like..
The surface of the Earth maintains an energy balance equation in which incoming energy from the sun is equal to outgoing energy. This is referred to as the Earth's surface energy balance, representing the long-term balance of energy in and out of the Earth system.
To elaborate, the incoming solar radiation (insolation) serves as the main energy source. A portion of this radiation is absorbed by the Earth's surface, leading to its heating. Another portion is absorbed by atmospheric gases like water vapor, carbon dioxide, and ozone, contributing to increased atmospheric temperatures through the absorption of shortwave solar radiation.
Subsequently, the heated surface emits longwave radiation, known as the surface's thermal infrared radiation, which moves upward from the surface. The atmosphere and clouds absorb a significant amount of this longwave radiation. Some of the energy is re-radiated back to the Earth's surface, while some escapes to space. This results in a balance where outgoing radiation matches incoming radiation at the top of the Earth's atmosphere.
The energy balance equation at any point on the Earth's surface can be expressed as follows:
Q* = QH + QE + QG + QL + QA + QS
Here:
Q* represents the net radiation flux into the Earth-atmosphere system.
QH denotes the flux of sensible heat, which refers to heat transfer between the Earth's surface and the atmosphere due to temperature differences.
QE is the flux of latent heat, which represents the energy absorbed or released during the phase change between liquid water and water vapor (evaporation and condensation).
QG is the flux of ground heat, which indicates the exchange of energy between the soil surface and the underlying ground.
QL represents the flux of longwave radiation, which signifies the exchange of thermal energy between the Earth's surface and the atmosphere.
QA is the flux of advective energy, which refers to the transfer of heat and moisture by winds.
QS is the flux of energy stored in the snow or ice cover.
These components collectively contribute to maintaining the energy balance of the Earth's surface and atmosphere system.
Learn more about surface
https://brainly.com/question/32235761
#SPJ11
A 7.8 cm diameter horizontal pipe gradually narrows to 4.8 cm . When water flows through this pipe at a certain rate, the gauge pressure in these two sections is 35.0 kPa and 21.0 kPa , respectively.
What is the volume rate of flow?
Bernoulli’s equation P₁ + ρgh₁ + 1/2 ρv₁² = P₂ + ρgh₂ + 1/2 ρv₂² Where; P₁ + 1/2 ρv₁² = pressure at point. Therefore, The volume rate of flow is 0.02 m³/s.
Diameter of horizontal pipe = 7.8 cm, Gradual narrowing to 4.8 cm. Gauge pressure in 1st section = 35.0 kPa, Gauge pressure in 2nd section = 21.0 kPa. The volume rate of flow is 0.02 m³/s.
Bernoulli’s equation P₁ + ρgh₁ + 1/2 ρv₁² = P₂ + ρgh₂ + 1/2 ρv₂²
Where;P₁ + 1/2 ρv₁² = pressure at point 1P₂ + 1/2 ρv₂² = pressure at point 2ρ = density of waterh₁ = height of water column at point 1h₂ = height of water column at point 2v₁ = velocity of water at point 1v₂ = velocity of water at point 2We are going to neglect the elevation difference between point 1 and point 2.
Now let's simplify the Bernoulli’s equation.P₁ + 1/2 ρv₁² = P₂ + 1/2 ρv₂²........(1)We know the diameter of the pipe at point 1 and point 2 but we are not given the velocity.
We can use the continuity equation to find velocity; A₁v₁ = A₂v₂A₁ = π(0.078/2)² = 0.0048 m², A₂ = π(0.048/2)² = 0.0018 m², A₁v₁ = A₂v₂v₂ = A₁v₁ / A₂ = 0.0048v₁ / 0.0018 = 13.33v₁
Now, we have found v₂ in terms of v₁. Substitute this value in equation (1) and simplify;P₁ + 1/2 ρv₁² = P₂ + 1/2 ρ (13.33v₁)²P₁ - P₂ = 1/2 ρ [(13.33)² - 1]v₁²ρ = 1000 kg/m³ (density of water at room temperature)P₁ - P₂ = 1/2 × 1000 × [(13.33)² - 1]v₁²P₁ - P₂ = 92,847v₁²........(2)
We have two equations (1) and (2) and two variables v₁ and P₁. Solve them simultaneously.
Let's rearrange equation (2) to find P₁;P₁ = P₂ + 92,847v₁²Plug this value of P₁ in equation (1) and
simplify ;
P₂ + 1/2 ρv₁²
= P₂ + 1/2 ρ (13.33v₁)² - 92,847v₁²1/2 ρ [(13.33)² - 1]v₁² = P₂ - P₂ + 92,847v₁²1/2 × 1000 × [(13.33)² - 1]v₁²
= 92,847v₁²v₁
= √[2(21 - 35) × 1000 / [(13.33)² - 1]]
= 2.68 m/s
Now, we have found the velocity of water. Let's find the volume rate of flow;Q = A₁v₁Q = π(0.078/2)² × 2.68Q = 0.000102 m³/s
The volume rate of flow is 0.02 m³/s.
Learn more about Bernoulli’s equation here:
https://brainly.com/question/30738722
#SPJ11
Section II: Data and Observations
4. Locate the data and observations collected in your lab guide. What are the key results? How
would you best summarize the data to relate your findings?
In order to analyze the experiment, we need to locate the data and observations in the lab guide, identify key results, and summarize the data to effectively convey our findings.
To locate the data and observations collected in your lab guide and summarize the key results, you can follow these steps:
1. Refer to your lab guide: Review the sections or instructions in your lab guide where you recorded the data and observations during the experiment.
2. Identify the key results: Look for the specific data points or measurements that are relevant to your experiment and research question. These could include numerical values, measurements, observations, or any other recorded information.
3. Organize the data: Arrange the data in a logical manner, such as in tables, graphs, or bullet points, depending on the format provided in your lab guide or the most appropriate way to present the information. Ensure that the data is clearly labeled and properly formatted for easy understanding.
4. Summarize the findings: Analyze the data and observations to identify the main patterns, trends, or conclusions that can be drawn from them. Consider any significant relationships, differences, or notable observations that are relevant to your research question or objective.
5. Present a summary: Write a concise summary that captures the key findings and observations from the data. Use clear and precise language to convey the main results and their implications. It is important to relate your findings back to your research question or objective to provide context and significance.
6. Use appropriate visuals: If applicable, include any tables, graphs, or charts that visually represent the data and support your summary. Visual aids can enhance the understanding and clarity of your findings.
know more about experiment here:
https://brainly.com/question/29451443
#SPJ8
A parallel beam of monochromatic light of wavelength passes through a slit of width b. After passing through the slit the light is incident on a distant screen. The angular width of the central maximum is A. 2 radians. B. 승 radians. C. 24 degrees. D. degrees. Hide Markscheme A
The correct answer is A. 2 radians. The standard unit of angular measurement used in many branches of mathematics is the radian, indicated by the symbol rad. It is the unit of angle in the International System of Units.
The angular width of the central maximum in a single-slit diffraction pattern can be calculated using the formula:
θ = λ / b
where θ is the angular width, λ is the wavelength of light, and b is the width of the slit.
In this case, the angular width is given as 2 radians. Since the options are given in different units, we need to convert 2 radians to degrees. Using the conversion factor 180/π, we have:
θ (in degrees) = (2 radians) * (180/π) ≈ 114.6 degrees = 2 radians.
To know more about radians
https://brainly.com/question/27025090
#SPJ11
Mercury is a fluid with a density of 13,600 kg/m3. What pressure in Pacals is exerted on an object under 0.76 meters of mercury? (g = 9.8 m/s2, use correct sig figs)
The pressure exerted on an object under 0.76 meters of mercury is approximately 99996 Pa.
The pressure exerted by a fluid at a certain depth can be calculated using the formula P = ρgh, where P is the pressure, ρ is the density of the fluid, g is the acceleration due to gravity, and h is the depth.
Given that the density of mercury is 13,600 kg/m^3, the depth is 0.76 meters, and the acceleration due to gravity is 9.8 m/s^2, we can calculate the pressure:
P = (13,600[tex]kg/m^3[/tex]) * (9.8 [tex]m/s^2[/tex]) * (0.76 m) ≈ 99996 Pa.
Therefore, the pressure exerted on the object under 0.76 meters of mercury is approximately 99996 Pa, rounded to the correct number of significant figures.
Learn more about pressure here :
https://brainly.com/question/30673967
#SPJ11
a) A 12-kVA, single-phase distribution transformer is connected to the 2300 V supply with resistances and leakage reactance of R1 = 3.96 2 R₂ = 0.0396 2, X₁= 15.8 2 and X₂ = 0.158 2. The iron loss is 420 W. The secondary voltage is 220 V. - (i) Calculate the equivalent impedance as referred to the high voltage side. (ii) Calculate the efficiency and maximum efficiency at 0.8 power factor. (7 marks) (12 marks) (b) A 3-phase, 4-pole, 50-Hz induction motor run at a speed of 1440 rpm. The total stator loss is 1 kW, and the total friction and winding losses is 2 kW. The power input to the induction motor is 40 kW. Calculate the efficiency of the motor.
(i) The equivalent impedance referred to the high voltage side is calculated as Z_eq = (0.0396 + j0.158) + ((220/2300)^2) * (3.96 + j15.8) Ω.(ii) The efficiency of the transformer can be calculated using η = (V₂ * I₂ * cos(θ)) / (V₁ * I₁), and the maximum efficiency at 0.8 power factor can be found by varying the power factor (θ) and calculating the efficiency for different values.
(i) To calculate the equivalent impedance as referred to the high voltage side, we need to account for the voltage ratio between the primary and secondary side of the transformer.
The equivalent impedance as referred to the high voltage side (Z_eq) can be calculated using the formula:
Z_eq = (Z₂ + (V₂/V₁)^2 * Z₁)
where Z₁ and Z₂ are the impedances on the primary and secondary side, respectively, and V₁ and V₂ are the primary and secondary voltages.
Given:
Z₁ = R₁ + jX₁ = 3.96 + j15.8 Ω
Z₂ = R₂ + jX₂ = 0.0396 + j0.158 Ω
V₁ = 2300 V
V₂ = 220 V
Substituting the values into the formula, we get:
Z_eq = (0.0396 + j0.158) + ((220/2300)^2) * (3.96 + j15.8)
(ii) To calculate the efficiency and maximum efficiency at 0.8 power factor, we need to consider the input and output power of the transformer.
The input power (Pin) can be calculated as:
Pin = VI * cos(θ)
The output power (Pout) can be calculated as:
Pout = VI * cos(θ) - iron loss - copper loss
Efficiency (η) can be calculated as:
η = Pout / Pin
To find the maximum efficiency, we need to vary the power factor (θ) and calculate the efficiency for different values.
(b) To calculate the efficiency of the motor, we need to consider the input power and the losses in the motor.
The input power (Pin) is given as 40 kW.
The total losses in the motor (Ploss) can be calculated as the sum of the stator loss and the friction and winding losses:
Ploss = 1 kW + 2 kW
The output power (Pout) is given by:
Pout = Pin - Ploss
Efficiency (η) can be calculated as:
η = Pout / Pin
Substituting the given values, we can calculate the efficiency of the motor.
To know more about voltage click here:
https://brainly.com/question/32002804
#SPJ11
The energy gap for silicon is 1.11eV at room temperature. Calculate the longest wavelength of a photon to excite the electron to the conducting band.
The longest wavelength of a photon to excite the electron to the conducting band is 1240 nm.
The energy gap for silicon is 1.11 eV at room temperature. To determine the longest wavelength of a photon to excite the electron to the conducting band, we can use the formula:E = hc/λwhere E is the energy of the photon, h is the Planck constant (6.626 x 10^-34 J s), c is the speed of light (2.998 x 10^8 m/s), and λ is the wavelength of the photon.
To excite an electron to the conduction band, the photon must have an energy of at least 1.11 eV. Therefore, we can write:E = 1.11 eV = 1.11 x 1.6 x 10^-19 J= 1.776 x 10^-19 J.
Substituting the values of h and c into the equation:E = hc/λλ = hc/ELet us solve for the wavelength:λ = hc/ELongest wavelength will correspond to the smallest energy of a photon, which would give a wavelength corresponding to the energy gap.λ = hc/E = (6.626 x 10^-34 J s)(2.998 x 10^8 m/s)/(1.776 x 10^-19 J) = 1.24 x 10^-6 m or 1240 nm.
Therefore, the longest wavelength of a photon to excite the electron to the conducting band is 1240 nm.
Learn more about wavelength here,
https://brainly.com/question/10750459
#SPJ11
A 5.5 kg block rests on a ramp with a 35° slope. The coefficients of static and kinetic friction are μs = 0.60 and μk = 0.44. If you push on the box with a force parallel to the ramp surface, what is the minimum amount of force needed to get the block moving? Provide labeled Force Diagram, Original formulas (before numbers are put in), formulas with numerical values entered.
The minimum amount of force needed to get the block moving is 19.4 N.
mass of block m= 5.5 kg
The slope of the ramp θ = 35°
The coefficient of static friction μs= 0.60
The coefficient of kinetic friction μk= 0.44
The force required to move the block is called the force of friction. If the force is large enough to move the block, then the force of friction equals the force of the push. If the force of the push is less than the force of friction, then the block will not move.
A force diagram can be drawn to determine the frictional force acting on the block.The gravitational force acting on the block can be broken down into two components, perpendicular and parallel to the ramp.The frictional force is acting up the ramp, opposing the force parallel to the ramp applied to the block.
To find the minimum amount of force needed to get the block moving, we have to consider the maximum frictional force. This maximum force of static friction is defined as
`μs * N`.
Where
`N = m * g` is the normal force acting perpendicular to the plane.
In general, the frictional force acting on an object is given by the following formula:
Frictional force, F = μ * N
Where
μ is the coefficient of friction
N is the normal force acting perpendicular to the plane
We have to consider the maximum static frictional force which is
`μs * N`.
To find the normal force, we need to find the component of gravitational force acting perpendicular to the ramp:
mg = m * g = 5.5 * 9.8 = 53.9 N
component of gravitational force parallel to ramp = m * g * sin θ = 53.9 * sin 35 = 30.97 N
component of gravitational force perpendicular to ramp = m * g * cos θ = 53.9 * cos 35 = 44.1 N
For an object on an incline plane, the normal force is equal to the component of gravitational force perpendicular to the ramp.
Thus, N = 44.1 N
maximum force of static friction = μs * N = 0.6 * 44.1 = 26.5 N
Now that we know the maximum force of static friction, we can determine the minimum force required to move the block.
The minimum force required to move the block is equal to the force of kinetic friction, which is defined as `μk * N`.
minimum force required to move the block = μk * N = 0.44 * 44.1 = 19.4 N
Therefore, the minimum amount of force needed to get the block moving is 19.4 N.
Learn more about coefficient of static and kinetic friction:
https://brainly.com/question/22438157
#SPJ11
Water at a gauge pressure of P = 5.2 atm at street level flows into an office building at a speed of 0.98 m/s through a pipe 4.8 cm in diameter. The pipe tapers down to 2.4 cm in diameter by the top floor, 16 m above (Figure 1). Assume no branch pipes and ignore viscosity.
Calculate the flow velocity in the pipe on the top floor.
Calculate the gauge pressure in the pipe on the top floor.
1. The flow velocity in the pipe on the top floor is approximately 3.909 m/s. 2. The gauge pressure at the top floor is approximately -1270.48 kPa.
To solve this problem, we can apply the principle of conservation of mass and Bernoulli's equation.
Given:
Diameter at the bottom (D1) = 4.8 cm = 0.048 m
Diameter at the top (D2) = 2.4 cm = 0.024 m
Velocity at the bottom (v1) = 0.98 m/s
Pressure at the bottom (P1) = 5.2 atm = 529.6 kPa
Height at the top (h2) = 16 m
1) Calculate the flow velocity at the top floor:
We can use the equation A1v1 = A2v2, where A1 and A2 are the cross-sectional areas of the pipe at the bottom and top floors, and v1 and v2 are the corresponding velocities.
Calculating the cross-sectional areas:
A1 = π(D1/2)^2 = π(0.048/2)^2 = 0.001808 m^2
A2 = π(D2/2)^2 = π(0.024/2)^2 = 0.000452 m^2
Using the equation A1v1 = A2v2, we can solve for v2:
v2 = (A1v1) / A2 = (0.001808 * 0.98) / 0.000452 ≈ 3.909 m/s
So, the flow velocity in the pipe on the top floor is approximately 3.909 m/s.
2) Calculate the at the top floor:
We'll use Bernoulli's equation to calculate the pressure difference between the two points:
P1 + 0.5ρv1^2 + ρgh1 = P2 + 0.5ρv2^2 + ρgh2
Since the pipe is open at the top, we can assume atmospheric pressure (P2) at the top floor.
Using the equation, we can solve for P2:
P2 = P1 + 0.5ρv1^2 + ρgh1 - 0.5ρv2^2 - ρgh2
To proceed, we need the density of water (ρ). The density of water is approximately 1000 kg/m^3.
Plugging in the values and calculating:
P2 = 529.6 kPa + 0.5 * 1000 * 0.98^2 + 1000 * 9.8 * 0 - 0.5 * 1000 * 3.909^2 - 1000 * 9.8 * 16
P2 ≈ 529.6 kPa + 0.4802 kPa - 1979.2 kPa - 301.4 kPa
P2 ≈ -1270.48 kPa
The gauge pressure at the top floor is approximately -1270.48 kPa. Note that the negative sign indicates the pressure is below atmospheric pressure.
Learn more about gauge pressure
https://brainly.com/question/30698101
#SPJ11
5. Two stones are dropped from the top of a bridge with height h. One stone has mass m₁ and the second stone has mass m₂=4*m₁. Let K₁ be the kinetic energy of the first stone and K₂ be the kinetic energy of the second stone when the stones hit the ground. Let v₁ be the velocity of the first stone and v₂ be the velocity of the second stone when the stones hit the ground. Which of the following is true about the kinetic energies and velocities of the two stones as they hit the ground? a. K₂=K₁, and v₂=V₁ b. K₂=4*K₁, and v₂=2*V₁ c. K₂=2*K₁, and v₂=4v₁ d. K₂=4*K₁, and v₂=V₁ 6. Which of the following statements is true for an isolated system in which there are nonconservative forces, such as friction, acting? a. The kinetic energy decreases, so the total energy of the system decreases b. Some energy is lost to the environment in the form of heat and mechanical waves c. Some energy is transferred into the internal energy of the system d. The system heats up, so the total energy of the system increases
When two stones of masses m₁ and m₂ are dropped from the same height, the gravitational potential energy they lose is converted into kinetic energy. The correct statement is: b. Some energy is lost to the environment in the form of heat and mechanical waves.
Since the stones are dropped from the same height, they have the same potential energy, which is converted entirely into kinetic energy when they hit the ground. The kinetic energy (K) of an object is given by the equation K = (1/2)mv², where m is the mass and v is the velocity.
Considering that m₂ = 4m₁, the kinetic energy of the second stone (K₂) will be four times the kinetic energy of the first stone (K₁), as the kinetic energy is directly proportional to the mass.
However, the velocities (v) of the stones will not necessarily be the same. The velocity depends on various factors such as the mass, height, and any other forces acting on the stones.
Therefore, the correct statement is:
b. K₂ = 4K₁, and v₂ ≠ 2v₁
For the second question:
When an isolated system has non conservative forces such as friction acting, some energy is lost to the environment in the form of heat and mechanical waves.
The total energy of an isolated system remains constant, but within the system, the energy may be transferred or transformed. In the presence of non conservative forces, such as friction, some of the mechanical energy is converted into other forms, such as heat or sound.
Therefore, the correct statement is: b. Some energy is lost to the environment in the form of heat and mechanical waves.
Learn more about mechanical waves here:
https://brainly.com/question/31180289
#SPJ11
Air is drawn from the atmosphere into a turbo- machine. At the exit, conditions are 500 kPa (gage) and 130°C. The exit speed is 100 m/s and the mass flow rate is 0.8 kg/s. Flow is steady and there is no heat transfer. Com- pute the shaft work interaction with the surroundings.
The shaft work interaction with the surroundings is 36.29 kJ/s or 36.29 kW (kiloWatt).
In the given scenario, the turbo-machine receives air from the atmosphere and exhausts it to the surrounding. Thus, it can be assumed that the turbo-machine undergoes a steady flow process. Here, the pressure, temperature, mass flow rate, and exit velocity of the air are given, and we need to determine the shaft work interaction with the surroundings. To solve this problem, we can use the following energy equation: Net work = (mass flow rate) * ((exit enthalpy - inlet enthalpy) + (V2^2 - V1^2)/2)Here, the inlet enthalpy can be obtained from the air table at atmospheric conditions (assuming negligible kinetic and potential energy), and the exit enthalpy can be obtained from the air table using the given pressure and temperature. Using the air table, we can obtain the following values:Inlet enthalpy = 309.66 kJ/kgExit enthalpy = 356.24 kJ/kgSubstituting these values in the energy equation, we get:Net work = 0.8 * ((356.24 - 309.66) + (100^2 - 0^2)/2)Net work = 36.29 kJ/s. Therefore, the shaft work interaction with the surroundings is 36.29 kJ/s or 36.29 kW (kiloWatt).
To know more about atmosphere visit:
https://brainly.com/question/13754083
#SPJ11
answer the question please with full steps
3. Determine Vn, Vout, and lout, assuming that the op amp is ideal. 1V 4ΚΩ w O 1.5mA 6k02 ww +5V -5V 3ΚΩ www 6V V₁ 3V 40+1₁ ww/... Vout 1kQ2
The Vn = 1V, Vout = 0.5V and Iout = -2.17mA (upwards towards V₁) .
Assuming the op amp is ideal. The circuit diagram is shown below: [tex]Circuit Diagram[/tex].We know that, the voltage at the inverting terminal of the op-amp (Vn) is equal to the voltage at the non-inverting terminal of the op-amp (Vp). So, Vn = VpLet's find Vp, Vp = Vin = 1V (Since there is no voltage drop across the resistor of 4kΩ)Therefore, Vn = Vp = 1V. Next, let's find the value of Vout. Vout can be obtained using the following formula: Vout = (Vn - Vf) * (R2/R1)Vf = 0, since the feedback resistor is connected directly from the output to the inverting input. Hence, Vf = 0Vout = (Vn - Vf) * (R2/R1) Vout = Vn * (R2/R1)Vout = 1 * (1kΩ/2kΩ) = 0.5V. Finally, let's find the value of Iout. Using KCL at node 2,I₂ = Iout + I₁I₁ = 1.5mAI₂ = (Vn - V₂)/R₂ = (1 - 3)/3kΩ = -0.67mA. Therefore, Iout = I₂ - I₁ ⇒Iout = -0.67mA - 1.5mA = -2.17mAA negative value of Iout indicates that the current is flowing in the opposite direction of the arrow shown in the circuit diagram. Therefore, the direction of the current is upwards towards V₁. The value of Iout is 2.17mA.
Hence, the final answers are, Vn = 1V,Vout = 0.5V and Iout = -2.17mA (upwards towards V₁).
Let's learn more about op amp:
https://brainly.com/question/30890598
#SPJ11
A rectangular loop of an area of 40.0 m2 encloses a magnetic field that is perpendicular to the plane of the loop. The magnitude of the magnetic varies with time as, B(t) = (14 T/s)t. The loop is connected to a 9.6 Ω resistor and a 16.0 pF capacitor in series. When fully charged, how much charge is stored on the capacitor?
The charge stored on the capacitor is 8.96 × 10⁻⁶ C (Coulombs).
Given information:Area of the rectangular loop = 40.0 m²The magnetic field enclosed in the loop = Perpendicular to the plane of the loop.Magnitude of magnetic field = (14 T/s)tResistor = 9.6 ΩCapacitor = 16.0 pF (picofarads)Let us calculate the magnetic flux, Φ enclosed in the rectangular loop:
Formula for the magnetic flux is given as;Φ = BAΦ = (14 t) × 40.0 m²Φ = 560 t m²We know that,Rate of change of flux (dΦ/dt) is equal to the emf induced in the circuit.Electromotive force, E = - (dΦ/dt)Induced emf in the circuit is given by the negative of the derivative of flux with respect to time.E = - dΦ/dtE = - d/dt (560 t m²)E = - 560 V (volts).
Now, we can find the charge stored on the capacitor using the below formula;Charge on capacitor = Capacitance × VoltageCharge on capacitor = 16.0 pF × 560 VCharge on capacitor = 8.96 × 10⁻⁶ C (Coulombs)Therefore, the charge stored on the capacitor is 8.96 × 10⁻⁶ C (Coulombs).
Learn more about Electromotive force here,
https://brainly.com/question/30083242
#SPJ11
This system starts from rest. M1 moves up the incline plane 8 m in 4 seconds. What is m1 's acceleration? m/s ∧
5 4 8 12 1 Question 2 If the mass of m1 is 30 kg, what is the sum of forces parallel to the incline? N 30 40 50 The kinetic coefficient of friction between m1 and the plane is 0.4 and the angle of the incline is 53 degrees, what is the tension in the cable? Assume acceleration due to gravity is 10 m/s ∧
2 41.2 51.2 61.2 71.2 Question 4 1 pts How much work does friction do? 7.2 −7.2 57.6 −57.6 What is the required mass for m2? kg 5.4 5.8 6.8
Question 1: the acceleration of m1 is 2 m/s^2.
Question 2:the sum of forces parallel to the incline is 120 N. Question 3:the tension in the cable is 61.2 N. Question 4: the required mass for m2 is 6.8 kg.
Question 1:Given,m1 = ?v1 = 0s = 4td1 = 8mNow, to find the acceleration of m1Acceleration formula, v = u + atv1 = u1 + a x 4where u1 = 0 as it starts from restv1 = a x 4a = v1/4a = 8/4a = 2m/s^2Therefore, the acceleration of m1 is 2 m/s^2.
Question 2:Given,Mass of m1 = 30 kgTo find the sum of forces parallel to the inclineWe need to calculate the force of friction Frictional force, F = μRwhere μ = 0.4R = mgR = 30 x 10R = 300 NTherefore,F = μR = 0.4 x 300F = 120 NTherefore, the sum of forces parallel to the incline is 120 N.
Question 3:Given,Mass of m1 = 30 kgKinetic coefficient of friction, μk = 0.4Angle of the incline, θ = 53°Tension in the cable = ?Acceleration due to gravity = g = 10 m/s^2We can resolve the forces acting on m1 as shown in the figure below:Here, Fp is the parallel force, Fn is the normal force, and T is the tension in the cable.
The equations of motion in the vertical and horizontal directions can be written as follows:Vertical direction:Fn – mg = 0Fn = mgFn = 30 x 10Fn = 300 NHence, the normal force, Fn = 300 NHorizontal direction:Fp – Ff – T = maFp = m1g sinθFf = μkFnFp = 30 x 10 x sin 53°Fp = 232.7 NAnd,Ff = μkFnFf = 0.4 x 300Ff = 120 NTotal force acting on the object,F = Fp – Ff – TTherefore,30 x 10 x sin 53° – 0.4 x 300 – T = 30 x 2T = 61.2 NTherefore, the tension in the cable is 61.2 N.
Question 4:Given,Work done by friction = ?Distance travelled by m1 = d1 = 8 mCoefficient of kinetic friction, μk = 0.4The work done by friction can be calculated as follows:Work done by friction = force of friction x distance= Ff x d1where,Ff = μkFnFf = 0.4 x 300Ff = 120 NTherefore,Work done by friction = 120 x 8Work done by friction = 960 JTherefore, the work done by friction is 960 J.Required mass for m2 = 6.8 kgHence, the required mass for m2 is 6.8 kg.
Learn more about kinetic friction here,
https://brainly.com/question/14111192
#SPJ11
2. Earth is closest to the Sun about January 4 and farthest from the Sun about July 5. Use Kepler's second law to determine on which of these dates Earth is travelling most rapidly and least rapidly.
Kepler's Second Law states that a line drawn between the Sun and a planet sweeps out equal areas in equal amounts of time. That is to say, a planet moves faster when it is nearer to the Sun and slower when it is farther away from it. On January 4th, the Earth is traveling most rapidly and on July 5th, the Earth is traveling least rapidly.
Let's see how Kepler's second law helps us determine the date on which the Earth is traveling most rapidly and least rapidly. Earth is closest to the Sun about January 4 and farthest from the Sun about July 5. Since the Earth is closer to the Sun during January, it is moving faster than when it is farther away from the Sun in July.
Learn more about Kepler's law:
https://brainly.com/question/16705471
#SPJ11